NXP Semiconductors
Data Sheet: Technical Data
MC56F826xx
Document Number MC56F826XXDS
Rev. 0, 08/2018
MC56F826XXDS
Supports MC56F82646VLF,
MC56F82643VLC, MC56F82623VLC
Features
• This family of digital signal controllers (DSCs) is
based on the 32-bit 56800EX core. On a single chip,
each device combines the processing power of a DSP
and the functionality of an MCU, with a flexible set of
peripherals to support many target applications:
– Industrial control
– Home appliances
– Motor control (ACIM, BLDC, PMSM, SR, stepper)
• DSC based on 32-bit 56800EX core
– Up to 100 MIPS at 100 MHz core frequency in fast
mode
– DSP and MCU functionality in a unified, C-efficient
architecture
• On-chip memory
– Up to 64 KB flash memory
– 8 KB data/program RAM
– On-chip flash memory and RAM can be mapped
into both program and data memory spaces
• Analog
– Two high-speed, 5-channel, 12-bit ADCs with
dynamic x1, x2, and x4 programmable amplifier
– Four analog comparators with integrated 6-bit DAC
references
• One FlexPWM module with up to 6 PWM outputs
• Communication interfaces
– Up to two high-speed queued SCI (QSCI) modules
with LIN slave functionality
• Timers
– One 16-bit quad timer (1 x 4 16-bit timer)
– Two Periodic Interval Timers (PITs)
• Security and integrity
– Cyclic Redundancy Check (CRC) generator
– Windowed Computer operating properly (COP)
watchdog
– External Watchdog Monitor (EWM)
• Clocks
– Two on-chip relaxation oscillators: 8 MHz (400 kHz
at standby mode) and 200 kHz
– Crystal / resonator oscillator
• System
– DMA controller
– Integrated power-on reset (POR) and low-voltage
interrupt (LVI) and brown-out reset module
– Inter-module crossbar connection
– JTAG/enhanced on-chip emulation (EOnCE) for
unobtrusive, real-time debugging
• Operating characteristics
– Single supply: 3.0 V to 3.6 V
– 5 V–tolerant I/O (except for RESETB pin which is a
3.3 V pin only)
– Operation ambient temperature: V temperature
option: -40°C to 105°C
• 48-pin LQFP, and 32-pin LQFP packages
NXP reserves the right to change the production detail specifications as may be
required to permit improvements in the design of its products.
Table of Contents
1
2
3
Overview............................................................................................ 3
6.1
Thermal handling ratings........................................................ 25
1.1
MC56F826xx Product Family.................................................3
6.2
Moisture handling ratings........................................................25
1.2
56800EX 32-bit Digital Signal Controller (DSC) core...........3
6.3
ESD handling ratings.............................................................. 25
1.3
Operation Parameters.............................................................. 4
6.4
Voltage and current operating ratings..................................... 26
1.4
On-Chip Memory and Memory Protection............................. 5
1.5
Interrupt Controller................................................................. 5
7.1
General characteristics............................................................ 27
1.6
Peripheral highlights............................................................... 6
7.2
AC electrical characteristics....................................................28
1.7
Block diagrams........................................................................10
7.3
Nonswitching electrical specifications....................................29
MC56F826xx signal and pin descriptions..........................................13
7.4
Switching specifications..........................................................35
2.1
7.5
Thermal specifications............................................................ 36
4
5
6
Signal groups...........................................................................18
Ordering parts.....................................................................................19
3.1
7
8
General............................................................................................... 27
Peripheral operating requirements and behaviors.............................. 37
Determining valid orderable parts...........................................19
8.1
Core modules...........................................................................37
Part identification............................................................................... 19
8.2
System modules.......................................................................38
4.1
Description.............................................................................. 19
8.3
Clock modules.........................................................................39
4.2
Format..................................................................................... 19
8.4
Memories and memory interfaces........................................... 41
4.3
Fields....................................................................................... 19
8.5
Analog..................................................................................... 43
4.4
Example...................................................................................20
8.6
Timer....................................................................................... 48
Terminology and guidelines...............................................................20
8.7
Communication interfaces.......................................................49
5.1
Definition: Operating requirement.......................................... 20
9
Design Considerations....................................................................... 50
5.2
Definition: Operating behavior............................................... 21
9.1
Thermal design considerations................................................50
5.3
Definition: Attribute................................................................21
9.2
Electrical design considerations.............................................. 51
5.4
Definition: Rating....................................................................21
9.3
Power-on Reset design considerations....................................53
5.5
Result of exceeding a rating.................................................... 22
10 Obtaining package dimensions.......................................................... 55
5.6
Relationship between ratings and operating requirements......22
11 Pinout................................................................................................. 55
5.7
Guidelines for ratings and operating requirements................. 23
11.1 Signal Multiplexing and Pin Assignments.............................. 55
5.8
Definition: Typical value........................................................ 23
11.2 Pinout diagrams.......................................................................57
5.9
Typical value conditions......................................................... 24
12 Product documentation.......................................................................59
Ratings................................................................................................25
MC56F826xx, Rev. 0, 08/2018
2
NXP Semiconductors
Overview
1 Overview
1.1 MC56F826xx Product Family
The following table is the comparsion of features among members of the family.
Table 1. MC56F826xx Family
Feature
MC56F82
Part Number
646VLF
643VLC
623VLC
Core frequency (MHz)
100/50
100/50
100/50
Flash memory (KB)
64
64
32
RAM (KB)
8
8
8
Interrupt Controller
Yes
Yes
Yes
Windowed Computer Operating Properly (WCOP)
1
1
1
External Watchdog Monitor (EWM)
1
1
1
Periodic Interrupt Timer (PIT)
2
2
2
Cyclic Redundancy Check (CRC)
1
1
1
Quad Timer (TMR)
1x4
1x4
1x4
12-bit Cyclic ADC channels
2x5
2x3
2x3
Input capture channels1
6
6
6
Standard channels
6
6
6
PWM Module:
DMA
Yes
Yes
Yes
Analog Comparators (CMP)
4
3
3
QSCI
2
1
1
GPIO
39
26
26
Package pin count
48 LQFP
32 LQFP
32 LQFP
1. Input capture shares the pin with cooresponding PWM channels.
1.2 56800EX 32-bit Digital Signal Controller (DSC) core
• Efficient 32-bit 56800EX Digital Signal Processor (DSP) engine with modified dual
Harvard architecture:
• Three internal address buses
• Four internal data buses: two 32-bit primary buses, one 16-bit secondary data
bus, and one 16-bit instruction bus
• 32-bit data accesses
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
3
Overview
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• Supports concurrent instruction fetches in the same cycle, and dual data accesses
in the same cycle
• 20 addressing modes
As many as 100 million instructions per second (MIPS) at 100 MHz core frequency
162 basic instructions
Instruction set supports both fractional arithmetic and integer arithmetic
32-bit internal primary data buses support 8-bit, 16-bit, and 32-bit data movement,
plus addition, subtraction, and logical operations
Single-cycle 16 × 16-bit -> 32-bit and 32 x 32-bit -> 64-bit multiplier-accumulator
(MAC) with dual parallel moves
32-bit arithmetic and logic multi-bit shifter
Four 36-bit accumulators, including extension bits
Parallel instruction set with unique DSP addressing modes
Hardware DO and REP loops
Bit reverse address mode, which effectively supports DSP and Fast Fourier
Transform algorithms
Full shadowing of the register stack for zero-overhead context saves and restores:
nine shadow registers correspond to nine address registers (R0, R1, R2, R3, R4, R5,
N, N3, M01)
Instruction set supports both DSP and controller functions
Controller-style addressing modes and instructions enable compact code
Enhanced bit manipulation instruction set
Efficient C compiler and local variable support
Software subroutine and interrupt stack, with the stack's depth limited only by
memory
Priority level setting for interrupt levels
JTAG/Enhanced On-Chip Emulation (OnCE) for unobtrusive, real-time debugging
that is independent of processor speed
1.3 Operation Parameters
• Up to 50 MHz operation in normal mode and 100 MHz operation in fast mode
• Operation ambient temperature:
-40 oC to 105oC
• Single 3.3 V power supply
• Supply range: VDD - VSS = 2.7 V to 3.6 V, VDDA - VSSA = 2.7 V to 3.6 V
MC56F826xx, Rev. 0, 08/2018
4
NXP Semiconductors
Overview
1.4 On-Chip Memory and Memory Protection
• Dual Harvard architecture permits as many as three simultaneous accesses to
program and data memory
• Internal flash memory with security and protection to prevent unauthorized access
• Memory resource protection (MRP) unit to protect supervisor programs and
resources from user programs
• Programming code can reside in flash memory during flash programming
• The dual-port RAM controller supports concurrent instruction fetches and data
accesses, or dual data accesses by the core.
• Concurrent accesses provide increased performance.
• The data and instruction arrive at the core in the same cycle, reducing latency.
• On-chip memory
• Up to 64 KB program/data flash memory
• 8 KB dual port data/program RAM
1.5 Interrupt Controller
• Five interrupt priority levels
• Three user-programmable priority levels for each interrupt source: level 0, level
1, level 2
• Unmaskable level 3 interrupts include illegal instruction, hardware stack
overflow, misaligned data access, SWI3 instruction
• Interrupt level 3 is highest priority and non-maskable. Its sources include:
• Illegal instructions
• Hardware stack overflow
• SWI instruction
• EOnce interrupts
• Misaligned data accesses
• Lowest-priority software interrupt: level LP
• Support for nested interrupts, so that a higher priority level interrupt request can
interrupt lower priority interrupt subroutine
• Masking of interrupt priority level is managed by the 56800EX core
• Two programmable fast interrupts that can be assigned to any interrupt source
• Notification to System Integration Module (SIM) to restart clock when in wait and
stop states
• Ability to relocate interrupt vector table
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
5
Peripheral highlights
1.6 Peripheral highlights
1.6.1 Flex Pulse Width Modulator (FlexPWM)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Up to 100 MHz operation clock with PWM Resolution as fine as 10 ns
PWM module contains four identical submodules, with two outputs per submodule
16 bits of resolution for center, edge-aligned, and asymmetrical PWMs
PWM outputs can be configured as complementary output pairs or independent
outputs
Dedicated time-base counter with period and frequency control per submodule
Independent top and bottom deadtime insertion for each complementary pair
Independent control of both edges of each PWM output
Enhanced input capture and output compare functionality on each input:
• Channels not used for PWM generation can be used for buffered output compare
functions.
• Channels not used for PWM generation can be used for input capture functions.
• Enhanced dual edge capture functionality
Synchronization of submodule to external hardware (or other PWM) is supported.
Double-buffered PWM registers
• Integral reload rates from 1 to 16
• Half-cycle reload capability
Multiple output trigger events can be generated per PWM cycle via hardware.
Support for double-switching PWM outputs
Up to eight fault inputs can be assigned to control multiple PWM outputs
• Programmable filters for fault inputs
Independently programmable PWM output polarity
Individual software control of each PWM output
All outputs can be programmed to change simultaneously via a FORCE_OUT event.
Option to supply the source for each complementary PWM signal pair from any of
the following:
• Crossbar module outputs
• External ADC input, taking into account values set in ADC high and low limit
registers
1.6.2 12-bit Analog-to-Digital Converter (Cyclic type)
• Two independent 12-bit analog-to-digital converters (ADCs):
• 2 x 5-channel external inputs
• Built-in x1, x2, x4 programmable gain pre-amplifier
MC56F826xx, Rev. 0, 08/2018
6
NXP Semiconductors
Peripheral highlights
•
•
•
•
•
•
•
•
• Maximum ADC clock frequency up to 10 MHz, having period as low as 100-ns
• Single conversion time of 10 ADC clock cycles
• Additional conversion time of 8 ADC clock cycles
Support of analog inputs for single-ended and differential, including unipolar
differential, conversions
Sequential, parallel, and independent scan mode
First 8 samples have offset, limit and zero-crossing calculation supported
ADC conversions can be synchronized by any module connected to the internal
crossbar module, such as PWM, timer, GPIO, and comparator modules.
Support for simultaneous triggering and software-triggering conversions
Support for a multi-triggering mode with a programmable number of conversions on
each trigger
Each ADC has ability to scan and store up to 8 conversion results.
Current injection protection
1.6.3 Periodic Interrupt Timer (PIT) Modules
• 16-bit counter with programmable count modulo
• PIT0 is master and PIT1 is slave (if synchronizing both PITs)
• The output signals of both PIT0 and PIT1 are internally connected to a peripheral
crossbar module
• Can run when the CPU is in Wait/Stop modes. Can also wake up the CPU from
Wait/Stop modes.
• In addition to its existing bus clock (up to 50 MHz), 3 alternate clock sources for the
counter clock are available:
• Crystal oscillator output
• 8 MHz / 400 kHz ROSC (relaxation oscillator output)
• On-chip low-power 200 kHz oscillator
1.6.4 Inter-Module Crossbar and AND-OR-INVERT logic
• Provides generalized connections between and among on-chip peripherals: ADCs,
comparators, quad-timers, FlexPWMs, EWM, and select I/O pins
• User-defined input/output pins for all modules connected to the crossbar
• DMA request and interrupt generation from the crossbar
• Write-once protection for all registers
• AND-OR-INVERT function provides a universal Boolean function generator that
uses a four-term sum-of-products expression, with each product term containing true
or complement values of the four selected inputs (A, B, C, D).
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
7
Peripheral highlights
1.6.5 Comparator
•
•
•
•
•
•
•
Full rail-to-rail comparison range
Support for high and low speed modes
Selectable input source includes external pins and internal DACs
Programmable output polarity
6-bit programmable DAC as a voltage reference per comparator
Three programmable hysteresis levels
Selectable interrupt on rising-edge, falling-edge, or toggle of a comparator output
1.6.6 Quad Timer
• Four 16-bit up/down counters, with a programmable prescaler for each counter
• Operation modes: edge count, gated count, signed count, capture, compare, PWM,
signal shot, single pulse, pulse string, cascaded, quadrature decode
• Programmable input filter
• Counting start can be synchronized across counters
• Up to 100 MHz operation clock
1.6.7 Queued Serial Communications Interface (QSCI) modules
•
•
•
•
•
•
•
•
Operating clock can be up to two times the CPU operating frequency
Four-word-deep FIFOs available on both transmit and receive buffers
Standard mark/space non-return-to-zero (NRZ) format
16-bit integer and 3-bit fractional baud rate selection
Full-duplex or single-wire operation
Programmable 8-bit or 9-bit data format
Error detection capability
Two receiver wakeup methods:
• Idle line
• Address mark
• 1/16 bit-time noise detection
• Up to 6.25 Mbit/s baud rate at 100 MHz operation clock
1.6.8 Windowed Computer Operating Properly (COP) watchdog
• Programmable windowed timeout period
• Support for operation in all power modes: run mode, wait mode, stop mode
MC56F826xx, Rev. 0, 08/2018
8
NXP Semiconductors
Peripheral highlights
• Causes loss of reference reset 128 cycles after loss of reference clock to the PLL is
detected
• Selectable reference clock source in support of EN60730 and IEC61508
• Selectable clock sources:
• External crystal oscillator/external clock source
• On-chip low-power 200 kHz oscillator
• System bus (IPBus up to 50 MHz)
• 8 MHz / 400 kHz ROSC
• Support for interrupt triggered when the counter reaches the timeout value
1.6.9 External Watchdog Monitor (EWM)
•
•
•
•
Monitors external circuit as well as the software flow
Programmable timeout period
Interrupt capability prior to timeout
Independent output (EWM_OUT_b) that places external circuit (but not CPU and
peripheral) in a safe mode when EWM timeout occurs
• Selectable reference clock source in support of EN60730 and IEC61508
• Wait mode and Stop mode operation is not supported.
• Selectable clock sources:
• External crystal oscillator/external clock source
• On-chip low-power 200 kHz oscillator
• System bus (IPBus up to 50 MHz)
• 8 MHz / 400 kHz ROSC
1.6.10 Power supervisor
• Power-on reset (POR) is released after VDD > 2.7 V during supply is ramped up;
CPU, peripherals, and JTAG/EOnCE controllers exit RESET state
• Brownout reset (VDD < 2.0 V)
• Critical warn low-voltage interrupt (LVI 2.2 V)
• Peripheral low-voltage warning interrupt (LVI 2.7 V)
1.6.11 Phase-locked loop
•
•
•
•
Wide programmable output frequency: 200 MHz to 400 MHz
Input reference clock frequency: 8 MHz to 16 MHz
Detection of loss of lock and loss of reference clock
Ability to power down
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
9
Clock sources
1.6.12 Clock sources
1.6.12.1 On-chip oscillators
• Tunable 8 MHz relaxation oscillator with 400 kHz at standby mode (divide-by-two
output)
• 200 kHz low frequency clock as secondary clock source for COP, EWM, PIT
1.6.12.2 Crystal oscillator
• Support for both high ESR crystal oscillator (ESR greater than 100 Ω) and ceramic
resonator
• Operating frequency: 4–16 MHz
1.6.13 Cyclic Redundancy Check (CRC) Generator
•
•
•
•
•
•
Hardware CRC generator circuit with 16-bit shift register
High-speed hardware CRC calculation
Programmable initial seed value
CRC16-CCITT compliancy with x16 + x12 + x5 + 1 polynomial
Error detection for all single, double, odd, and most multibit errors
Option to transpose input data or output data (CRC result) bitwise, which is required
for certain CRC standards
1.6.14 General Purpose I/O (GPIO)
•
•
•
•
•
•
•
5 V tolerance (except RESETB pin)
Individual control of peripheral mode or GPIO mode for each pin
Programmable push-pull or open drain output
Configurable pullup or pulldown on all input pins
All pins (except JTAG and RESETB) default to be GPIO inputs
2 mA / 9 mA source/sink capability
Controllable output slew rate
1.7 Block diagrams
The 56800EX core is based on a modified dual Harvard-style architecture, consisting of
three execution units operating in parallel, and allowing as many as six operations per
instruction cycle. The MCU-style programming model and optimized instruction set
MC56F826xx, Rev. 0, 08/2018
10
NXP Semiconductors
Clock sources
enable straightforward generation of efficient and compact code for the DSP and control
functions. The instruction set is also efficient for C compilers, to enable rapid
development of optimized control applications.
The device's basic architecture appears in Figure 1 and Figure 2. Figure 1 shows how the
56800EX system buses communicate with internal memories, and the IPBus interface
and the internal connections among the units of the 56800EX core. Figure 2 shows the
peripherals and control blocks connected to the IPBus bridge. See the specific device’s
Reference Manual for details.
DSP56800EX Core
Program Control Unit
PC
LA
LA2
HWS0
HWS1
FIRA
OMR
SR
LC
LC2
FISR
Address
Generation
Unit
(AGU)
Instruction
Decoder
Interrupt
Unit
ALU1
ALU2
R0
R1
R2
R2
R3
R3
R4
R4
R5
R5
N
M01
N3
Looping
Unit
Program
Memory
SP
XAB1
XAB2
PAB
PDB
Data/
Program
RAM
CDBW
CDBR
XDB2
A2
B2
C2
D2
BitManipulation
Unit
Enhanced
OnCE™
JTAG TAP
Y
A1
B1
C1
D1
Y1
Y0
X0
MAC and ALU
A0
B0
C0
D0
IPBus
Interface
Data
Arithmetic
Logic Unit
(ALU)
Multi-Bit Shifter
Figure 1. 56800EX basic block diagram
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
11
Clock sources
56800EX CPU
Address
Generation
Unit (AGU)
Bit
Manipulation
Unit
Arithmetic
Logic Unit
(ALU)
Crystal OSC
CRC
PLL
Clock MUX
Internal
8 MHz
Internal
200 kHz
Core Data Bus
Secondary Data Bus
Platform Bus
Crossbar Swirch
Program
Controller
(PC)
Program Bus
Memory Resource
Protection Unit
4
EOnCE
Flash Controller
and Cache
JTAG
Program/Data Flash
Up to 64KB
Data/Program RAM
8KB
DMA Controller
Interrupt Controller
Windowed
Watchdog (WCOP)
Power Management
Controller (PMC)
Periodic Interrupt
Timer (PIT) 0, 1
System Integration
Module (SIM)
Peripheral Bus
QSCI
0,1
Quad Timer
FlexPWM
EWM
Package
Pins
ADC A ADC B
12bit 12bit
Inter Module Crossbar Inputs
GPIO & Peripheral MUX
Inter-Module
Crossbar B
AND-OR-INV
Logic
Peripheral Bus
Inter Module Crossbar Outputs
Inter Module connection
Inter-Module
Crossbar A
Comparators with
6bit DAC A,B,C,D
Peripheral Bus
Figure 2. System diagram
MC56F826xx, Rev. 0, 08/2018
12
NXP Semiconductors
MC56F826xx signal and pin descriptions
2 MC56F826xx signal and pin descriptions
After reset, each pin is configured for its primary function (listed first). Any alternative
functionality, shown in parentheses, must be programmed through the GPIO module
peripheral enable registers (GPIOx_PER) and the SIM module GPIO peripheral select
(GPSx) registers. All GPIO ports can be individually programmed as an input or output
(using bit manipulation).
• PWMA_FAULT0, PWMA_FAULT1, and similar signals are inputs used to disable
selected PWMA outputs, in cases where the fault conditions originate off-chip.
For the MC56F826xx products, which use 48-pin LQFP and 32-pin packages:
Table 2. Signal descriptions
Signal Name
VDD
48 LQFP
32 LQFP
32
—
44
28
22
14
31
—
45
29
VDDA
15
VSSA
VCAP
VSS
Type
State During
Reset
Signal Description
Supply
Supply
I/O Power — Supplies 3.3 V power to the
chip I/O interface.
Supply
Supply
I/O Ground — Provide ground for the device
I/O interface.
9
Supply
Supply
Analog Power — Supplies 3.3 V power to
the analog modules. It must be connected to
a clean analog power supply.
16
10
Supply
Supply
Analog Ground — Supplies an analog
ground to the analog modules. It must be
connected to a clean power supply.
19
—
43
27
On-chip
regulator
output
On-chip
regulator output
Connect a 2.2 µF bypass capacitor between
this pin and VSS to stabilize the core voltage
regulator output required for proper device
operation.
NOTE: The total bypass capacitor value
between all VCAP pin and VSS
should not exceed 4.7 µF.
TDI
48
32
(GPIOD0)
TDO
Input, internal
pullup enabled
Input/Output
46
30
(GPIOD1)
TCK
Input
1
1
Test Data Input — It is sampled on the rising
edge of TCK and has an internal pullup
resistor. After reset, the default state is TDI.
GPIO Port D0
Output
Output
Test Data Output — It is driven in the shift-IR
and shift-DR controller states, and it changes
on the falling edge of TCK. After reset, the
default state is TDO
Input/Output
Output
GPIO Port D1
Input
Input, internal
pulldown
enabled
Test Clock Input — The pin is connected
internally to a pulldown resistor. A Schmitttrigger input is used for noise immunity. After
reset, the default state is TCK
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
13
MC56F826xx signal and pin descriptions
Table 2. Signal descriptions (continued)
Signal Name
48 LQFP
32 LQFP
(GPIOD2)
TMS
Type
State During
Reset
Input/Output
47
31
Input
Signal Description
GPIO Port D2
Input, internal
pullup enabled
Test Mode Select Input — It is sampled on
the rising edge of TCK and has an internal
pullup resistor. After reset, the default state
is TMS.
NOTE: Always tie the TMS pin to VDD
through a 2.2 kΩ resistor if need to
keep on-board debug capability.
Otherwise, directly tie to VDD.
(GPIOD3)
Input/Output
RESET or RESETB 2
2
(GPIOD4)
GPIOA0
Input
GPIO Port D3
Input, internal
pullup enabled
Input/
Opendrain
Output
9
6
Input/Output
Reset — A direct hardware reset on the
processor. When RESET is asserted low,
the device is initialized and placed in the
reset state. A Schmitt-trigger input is used
for noise immunity. The internal reset signal
is deasserted synchronous with the internal
clocks after a fixed number of internal clocks.
After reset, the default state is RESET.
Recommended a capacitor of up to 0.1 µF
for filtering noise.
GPIO Port D4 RESET functionality is
disabled in this mode and the device can be
reset only through POR, COP reset, or
software reset.
Input
GPIO Port A0
(ANA0&CMPA_IN3)
Input
ANA0 is analog input to channel 0 of ADCA;
CMPA_IN3 is positive input 3 of analog
comparator A. After reset, the default state is
GPIOA0.
(CMPC_O)
Output
Analog comparator C output
GPIOA1
10
7
(ANA1&CMPA_IN0)
GPIOA2
Input
Input
11
8
(ANA2&VREFHA&C
MPA_IN1)
GPIOA3
Input/Output
Input/Output
ANA1 is analog input to channel 1 of ADCA;
CMPA_IN0 is negative input 0 of analog
comparator A. When used as an analog
input, the signal goes to ANA1 and
CMPA_IN0. The ADC control register
configures this input as ANA1 or CMPA_IN0.
Input
Input
12
—
Input/Output
GPIO Port A1: After reset, the default state is
GPIOA1.
GPIO Port A2: After reset, the default state is
GPIOA2.
ANA2 is analog input to channel 2 of ADCA;
VREFHA is analog reference high of ADCA;
CMPA_IN1 is negative input 1 of analog
comparator A. When used as an analog
input, the signal goes to both ANA2,
VREFHA, and CMPA_IN1.
Input
GPIO Port A3: After reset, the default state is
GPIOA3.
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
14
NXP Semiconductors
MC56F826xx signal and pin descriptions
Table 2. Signal descriptions (continued)
Signal Name
48 LQFP
32 LQFP
(ANA3&VREFLA&C
MPA_IN2)
GPIOA4
8
—
17
11
18
12
20
13
21
—
(EXTAL)
Input/Output
Input/Output
Input/Output
14
—
Input/Output
Input
—
Input/Output
GPIO Port B1: After reset, the default state is
GPIOB1.
ANB1 is analog input to channel 1 of ADCB;
CMPB_IN0 is negative input 0 of analog
comparator B. When used as an analog
input, the signal goes to ANB1 and
CMPB_IN0. The ADC control register
configures this input as ANB1.
Input
GPIO Port B2: After reset, the default state is
GPIOB2.
ANB2 is analog input to channel 2 of ADCB;
VREFHB is analog reference high of ADCB;
CMPC_IN3 is positive input 3 of analog
comparator C. When used as an analog
input, the signal goes to both ANB2 and
CMPC_IN3.
Input
GPIO Port B3: After reset, the default state is
GPIOB3.
ANB3 is analog input to channel 3 of ADCB;
VREFLB is analog reference low of ADCB;
CMPC_IN0 is negative input 0 of analog
comparator C.
Input
Input
3
GPIO Port B0: After reset, the default state is
GPIOB0.
ANB0 is analog input to channel 0 of ADCB;
CMPB_IN3 is positive input 3 of analog
comparator B. When used as an analog
input, the signal goes to ANB0 and
CMPB_IN3. The ADC control register
configures this input as ANB0.
Input
(ANB4&CMPC_IN1)
GPIOC0
Input
Input
(ANB3&VREFLB&C
MPC_IN0)
GPIOB4
Input/Output
GPIO Port A4: After reset, the default state is
GPIOA4.
ANA4 is Analog input to channel 4 of ADCA;
CMPD_IN0 is input 0 to comparator D.
Input
(ANB2&VERFHB&C
MPC_IN3)
GPIOB3
Input
Input
(ANB1&CMPB_IN0)
GPIOB2
Input/Output
Signal Description
ANA3 is analog input to channel 3 of ADCA;
VREFLA is analog reference low of ADCA;
CMPA_IN2 is negative input 2 of analog
comparator A.
Input
(ANB0&CMPB_IN3)
GPIOB1
State During
Reset
Input
(ANA4&CMPD_IN0)
GPIOB0
Type
GPIO Port B4: After reset, the default state is
GPIOB4.
ANB4 is analog input to channel 4 of ADCB;
CMPC_IN1 is negative input 1 of analog
comparator C.
Input
Analog Input
GPIO Port C0: After reset, the default state
is GPIOC0.
The external crystal oscillator input (EXTAL)
connects the internal crystal oscillator input
to an external crystal or ceramic resonator.
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
15
MC56F826xx signal and pin descriptions
Table 2. Signal descriptions (continued)
Signal Name
48 LQFP
32 LQFP
(CLKIN0)
GPIOC1
State During
Reset
4
—
Input/Output
Input
Input
5
3
Input/Output
Signal Description
External clock input 01
Input
(XTAL)
GPIOC2
Type
GPIO Port C1: After reset, the default state
is GPIOC1.
The external crystal oscillator output (XTAL)
connects the internal crystal oscillator output
to an external crystal or ceramic resonator.
Input
GPIO Port C2: After reset, the default state
is GPIOC2.
(TXD0)
Output
SCI0 transmit data output or transmit/receive
in single wire operation
(XB_OUT11)
Output
Crossbar module output 11
(XB_IN2)
Input
Crossbar module input 2
(CLKO0)
Output
Buffered clock output 0: the clock source is
selected by clockout select (CLKOSEL) bits
in the clock output select register (CLKOUT)
of the SIM.
GPIOC3
6
4
Input/Output
Input
GPIO Port C3: After reset, the default state
is GPIOC3.
(TA0)
Input/Output
Quad timer module A channel 0 input/output
(CMPA_O)
Output
Analog comparator A output
(RXD0)
Input
SCI0 receive data input
(CLKIN1)
Input
External clock input 1
GPIOC4
7
5
Input/Output
Input
GPIO Port C4: After reset, the default state
is GPIOC4.
(TA1)
Input/Output
Quad timer module A channel 1 input/output
(CMPB_O)
Output
Analog comparator B output
(XB_IN6)
Input
Crossbar module input 6
(EWM_OUT_B)
Output
External Watchdog Module output
GPIOC5
13
—
(XB_IN7)
GPIOC6
Input/Output
Input
Input
23
15
Input/Output
GPIO Port C5: After reset, the default state
is GPIOC5.
Crossbar module input 7
Input
GPIO Port C6: After reset, the default state
is GPIOC6.
(TA2)
Input/Output
Quad timer module A channel 2 input/output
(XB_IN3)
Input
Crossbar module input 3
(CMP_REF)
Analog Input
Positive input 3 of analog comparator A and
B and C.
GPIOC7
24
—
Input/Output
Input
GPIO Port C7: After reset, the default state
is GPIOC7.
(TXD0)
Output
SCI0 transmit data output or transmit/receive
in single wire operation
(XB_IN8)
Input
Crossbar module input 8
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
16
NXP Semiconductors
MC56F826xx signal and pin descriptions
Table 2. Signal descriptions (continued)
Signal Name
GPIOC8
48 LQFP
25
32 LQFP
16
Type
Input/Output
State During
Reset
Input
Signal Description
GPIO Port C8: After reset, the default state
is GPIOC8.
(RXD0)
Input
SCI0 receive data input
(XB_IN9)
Input
Crossbar module input 9
(XB_OUT6)
Output
Crossbar module output 6
GPIOC9
26
17
Input/Output
Input
GPIO Port C9: After reset, the default state
is GPIOC9.
(XB_IN4)
Input
Crossbar module input 4
(TXD0)
Output
SCI0 transmit data output or transmit/receive
in single wire operation
(XB_OUT8)
Output
Crossbar module output 8
GPIOC10
27
18
Input/Output
Input
GPIO Port C10: After reset, the default state
is GPIOC10.
(XB_IN5)
Input
Crossbar module input 4
(XB_OUT9)
Output
Crossbar module output 9
GPIOC11
29
—
(TXD1)
GPIOC12
Input
Output
30
—
37
—
(RXD1)
GPIOC13
Input/Output
Input/Output
SCI1 transmit data output or transmit/receive
in single wire operation
Input
Input
Input/Output
GPIO Port C11: After reset, the default state
is GPIOC11.
GPIO Port C12: After reset, the default state
is GPIOC12.
SCI1 receive data input
Input
GPIO Port C13: After reset, the default state
is GPIOC13.
(TA3)
Input/Output
Quad timer module A channel 3 input/output
(XB_IN6)
Input
Crossbar module input 6
(EWM_OUT_B)
Output
External Watchdog Module output
GPIOC14
41
—
Input/Output
Input
GPIO Port C14: After reset, the default state
is GPIOC14.
(XB_OUT4)
Output
Crossbar module output 4
(PWM_FAULT4)
Input
Disable PWMA output 4
GPIOC15
42
—
(XB_OUT5)
21
(PWM_0A)
Input/Output
Disable PWMA output 5
Input
Input/Output
34
22
Input/Output
GPIO Port C15: After reset, the default state
is GPIOC15.
Crossbar module output 5
Input
33
(PWM_0B)
GPIOE1
Input
Output
(PWM_FAULT5)
GPIOE0
Input/Output
GPIO Port E0: After reset, the default state is
GPIOE0.
PWM module A , submodule 0, output B or
input capture B
Input
Input/Output
GPIO Port E1: After reset, the default state is
GPIOE1.
PWM module A , submodule 0, output A or
input capture A
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
17
MC56F826xx signal and pin descriptions
Table 2. Signal descriptions (continued)
Signal Name
GPIOE2
48 LQFP
35
32 LQFP
23
(PWMA_1B)
GPIOE3
Input/Output
State During
Reset
Input
Input/Output
36
24
(PWMA_1A)
GPIOE4
Type
Input/Output
25
Input/Output
GPIO Port E2: After reset, the default state is
GPIOE2.
PWM module A , submodule 1, output B or
input capture B
Input
Input/Output
39
Signal Description
GPIO Port E3: After reset, the default state is
GPIOE3.
PWM module A , submodule 1, output A or
input capture A
Input
GPIO Port E4: After reset, the default state is
GPIOE4.
(PWMA_2B)
Input/Output
PWM module A , submodule 2, output B or
input capture B
(XB_IN2)
Input
Crossbar module input 2
GPIOE5
40
26
Input/Output
Input
GPIO Port E5: After reset, the default state is
GPIOE5.
(PWMA_2A)
Input/Output
PWM module A , submodule 2, output A or
input capture A
(XB_IN3)
Input
Crossbar module input 3
GPIOF0
28
—
38
—
(XB_IN6)
GPIOF1
Input/Output
Input
Input
Input/Output
GPIO Port F0: After reset, the default state is
GPIOF0.
Crossbar module input 6
Input
GPIO Port F1: After reset, the default state is
GPIOF1.
(CLKO1)
Output
Buffered clock output 1: the clock source is
selected by clockout select (CLKOSEL) bits
in the clock output select register (CLKOUT)
of the SIM.
(XB_IN7)
Input
Crossbar module input 7
(CMPD_O)
Output
Analog comparator D output
GPIOF2
—
19
—
20
(XB_OUT6)
GPIOF3
Input/Output
Input
Output
(XB_OUT7)
Input/Output
GPIO Port F2: After reset, the default state is
GPIOF2.
Crossbar module output 6
Input
Output
GPIO Port F3: After reset, the default state is
GPIOF3.
Crossbar module output 7
1. If CLKIN is selected as the device’s external clock input, then both the GPS_C0 bit (in GPS1) and the EXT_SEL bit (in
OCCS oscillator control register (OSCTL)) must be set. Also, the crystal oscillator should be powered down.
2.1 Signal groups
The input and output signals of the MC56F826xx are organized into functional groups, as
detailed in the following table.
MC56F826xx, Rev. 0, 08/2018
18
NXP Semiconductors
Ordering parts
Table 3. Functional Group Pin Allocations
Functional Group
Number of Pins
32LQFP
48LQFP
Power Inputs (VDD, VDDA), Power output( VCAP)
3
5
Ground (VSS, VSSA)
3
4
Reset
1
1
FlexPWM ports not including fault pins
6
6
Queued Serial Communications Interface (QSCI0 and QSCI1) ports
4
7
12-bit Analog-to-Digital Converter inputs
6
10
Analog Comparator inputs/outputs
7/3
11/4
Quad Timer Module (TMRA and TMRB) ports
3
4
Inter-Module Crossbar inputs/outputs
8/4
12/6
Clock inputs/outputs
1/1
2/2
JTAG / Enhanced On-Chip Emulation (EOnCE)
4
4
3 Ordering parts
3.1 Determining valid orderable parts
Valid orderable part numbers are provided on the web. To determine the orderable part
numbers for this device, go to nxp.com and perform a part number search for the
following device numbers: MC56F82
4 Part identification
4.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
4.2 Format
Part numbers for this device have the following format: Q 56F8 2 C F P T PP N
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
19
Terminology and guidelines
4.3 Fields
This table lists the possible values for each field in the part number (not all combinations
are valid):
Field
Description
Values
Q
Qualification status
• MC = Fully qualified, general market flow
• PC = Prequalification
56F8
DSC family with flash memory and DSP56800/
DSP56800E/DSP56800EX core
• 56F8
2
DSC subfamily
• 2
C
Maximum CPU frequency (MHz)
• 6 = 100 MHz
F
Primary program flash memory size
• 2 = 32 KB
• 4 = 64 KB
P
Pin count
• 3 = 32
• 6 = 48
T
Temperature range (°C)
• V = –40 to 105
PP
Package identifier
• LC = 32LQFP
• LF = 48LQFP
N
Packaging type
• R = Tape and reel
• (Blank) = Trays
4.4 Example
This is an example part number: MC56F82646VLF
5 Terminology and guidelines
5.1 Definition: Operating requirement
An operating requirement is a specified value or range of values for a technical
characteristic that you must guarantee during operation to avoid incorrect operation and
possibly decreasing the useful life of the chip.
5.1.1 Example
This is an example of an operating requirement:
MC56F826xx, Rev. 0, 08/2018
20
NXP Semiconductors
Terminology and guidelines
Symbol
VDD
Description
Min.
1.0 V core supply
voltage
0.9
Max.
1.1
Unit
V
5.2 Definition: Operating behavior
Unless otherwise specified, an operating behavior is a specified value or range of values
for a technical characteristic that are guaranteed during operation if you meet the
operating requirements and any other specified conditions.
5.2.1 Example
This is an example of an operating behavior:
Symbol
IWP
Description
Min.
Digital I/O weak pullup/ 10
pulldown current
Max.
130
Unit
µA
5.3 Definition: Attribute
An attribute is a specified value or range of values for a technical characteristic that are
guaranteed, regardless of whether you meet the operating requirements.
5.3.1 Example
This is an example of an attribute:
Symbol
CIN_D
Description
Input capacitance:
digital pins
Min.
—
Max.
7
Unit
pF
5.4 Definition: Rating
A rating is a minimum or maximum value of a technical characteristic that, if exceeded,
may cause permanent chip failure:
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
21
Terminology and guidelines
• Operating ratings apply during operation of the chip.
• Handling ratings apply when the chip is not powered.
5.4.1 Example
This is an example of an operating rating:
Symbol
VDD
Description
1.0 V core supply
voltage
Min.
–0.3
Max.
1.2
Unit
V
5.5 Result of exceeding a rating
Failures in time (ppm)
40
30
The likelihood of permanent chip failure increases rapidly as
soon as a characteristic begins to exceed one of its operating ratings.
20
10
0
Operating rating
Measured characteristic
MC56F826xx, Rev. 0, 08/2018
22
NXP Semiconductors
Terminology and guidelines
5.6 Relationship between ratings and operating requirements
e
Op
ing
rat
r
(
ng
ati
n.
mi
)
ing
rat
e
Op
e
re
ir
qu
)
in.
t (m
n
me
ing
rat
e
Op
e
re
ir
qu
t (m
n
me
ax
.)
ing
rat
e
Op
(m
ng
ati
.)
ax
r
Fatal range
Degraded operating range
Normal operating range
Degraded operating range
Fatal range
Expected permanent failure
- No permanent failure
- Possible decreased life
- Possible incorrect operation
- No permanent failure
- Correct operation
- No permanent failure
- Possible decreased life
- Possible incorrect operation
Expected permanent failure
–∞
∞
Operating (power on)
ng
dli
n
Ha
n.)
mi
g(
in
rat
ma
g(
ng
dli
n
Ha
in
rat
x.)
Fatal range
Handling range
Fatal range
Expected permanent failure
No permanent failure
Expected permanent failure
–∞
Handling (power off)
∞
5.7 Guidelines for ratings and operating requirements
Follow these guidelines for ratings and operating requirements:
• Never exceed any of the chip’s ratings.
• During normal operation, don’t exceed any of the chip’s operating requirements.
• If you must exceed an operating requirement at times other than during normal
operation (for example, during power sequencing), limit the duration as much as
possible.
5.8 Definition: Typical value
A typical value is a specified value for a technical characteristic that:
• Lies within the range of values specified by the operating behavior
• Given the typical manufacturing process, is representative of that characteristic
during operation when you meet the typical-value conditions or other specified
conditions
Typical values are provided as design guidelines and are neither tested nor guaranteed.
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
23
Terminology and guidelines
5.8.1 Example 1
This is an example of an operating behavior that includes a typical value:
Symbol
Description
IWP
Digital I/O weak
pullup/pulldown
current
Min.
10
Typ.
70
Max.
130
Unit
µA
5.8.2 Example 2
This is an example of a chart that shows typical values for various voltage and
temperature conditions:
5000
4500
4000
TJ
IDD_STOP (μA)
3500
150 °C
3000
105 °C
2500
25 °C
2000
–40 °C
1500
1000
500
0
0.90
0.95
1.00
1.05
1.10
VDD (V)
5.9 Typical value conditions
Typical values assume you meet the following conditions (or other conditions as
specified):
Symbol
Description
Value
Unit
TA
Ambient temperature
25
°C
VDD
3.3 V supply voltage
3.3
V
MC56F826xx, Rev. 0, 08/2018
24
NXP Semiconductors
Ratings
6 Ratings
6.1 Thermal handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
TSTG
Storage temperature
–55
150
°C
1
TSDR
Solder temperature, lead-free
—
260
°C
2
1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life.
2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
6.2 Moisture handling ratings
Symbol
MSL
Description
Moisture sensitivity level
Min.
Max.
Unit
Notes
—
3
—
1
1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
6.3 ESD handling ratings
Although damage from electrostatic discharge (ESD) is much less common on these
devices than on early CMOS circuits, use normal handling precautions to avoid exposure
to static discharge. Qualification tests are performed to ensure that these devices can
withstand exposure to reasonable levels of static without suffering any permanent
damage.
All ESD testing is in conformity with AEC-Q100 Stress Test Qualification. During the
device qualification ESD stresses were performed for the human body model (HBM), the
machine model (MM), and the charge device model (CDM).
All latch-up testing is in conformity with AEC-Q100 Stress Test Qualification.
A device is defined as a failure if after exposure to ESD pulses, the device no longer
meets the device specification. Complete DC parametric and functional testing is
performed as per the applicable device specification at room temperature followed by hot
temperature, unless specified otherwise in the device specification.
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
25
Ratings
Table 4. ESD/Latch-up Protection
Characteristic1
Min
Max
Unit
ESD for Human Body Model (HBM)
–2000
+2000
V
ESD for Machine Model (MM)
–200
+200
V
ESD for Charge Device Model (CDM)
–500
+500
V
Latch-up current at TA= 85°C (ILAT)
–100
+100
mA
1. Parameter is achieved by design characterization on a small sample size from typical devices under typical conditions
unless otherwise noted.
6.4 Voltage and current operating ratings
Absolute maximum ratings are stress ratings only, and functional operation at the
maxima is not guaranteed. Stress beyond the limits specified in Table 5 may affect device
reliability or cause permanent damage to the device.
NOTE
If the voltage difference between VDD and VDDA or VSS and
VSSA is too large, then the device can malfunction or be
permanently damaged. The restrictions are:
• At all times, it is recommended that the voltage
difference of VDD - VSS be within +/-200 mV of the
voltage difference of VDDA - VSSA, including power
ramp up and ramp down; see additional requirements in
Table 6. Failure to do this recommendation may result in a
harmful leakage current through the substrate, between the
VDD/VSS and VDDA/VSSA pad cells. This harmful
leakage current could prevent the device from operating
after power up.
• At all times, to avoid permanent damage to the part, the
voltage difference between VDD and VDDA must
absolutely be limited to 0.3 V; see Table 5.
• At all times, to avoid permanent damage to the part, the
voltage difference between VSS and VSSA must
absolutely be limited to 0.3 V; see Table 5.
Table 5. Absolute Maximum Ratings (VSS = 0 V, VSSA = 0 V)
Characteristic
Symbol
Notes1
Min
Max
Unit
Supply Voltage Range
VDD
-0.3
4.0
V
Analog Supply Voltage Range
VDDA
-0.3
4.0
V
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
26
NXP Semiconductors
General
Table 5. Absolute Maximum Ratings (VSS = 0 V, VSSA = 0 V) (continued)
Characteristic
Symbol
Notes1
Min
Max
Unit
VREFHx
-0.3
4.0
V
Voltage difference VDD to VDDA
ΔVDD
-0.3
0.3
V
Voltage difference VSS to VSSA
ΔVSS
-0.3
0.3
V
ADC High Voltage Reference
Digital Input Voltage Range
VIN
Pin Group 1
-0.3
5.5
V
RESET Input Voltage Range
VIN_RESET
Pin Group 2
-0.3
4.0
V
VOSC
Pin Group 4
-0.4
4.0
V
VINA
Pin Group 3
-0.3
4.0
V
—
-5.0
mA
Oscillator Input Voltage Range
Analog Input Voltage Range
Input clamp current, per pin (VIN < VSS - 0.3
V), 2, 3
VIC
pin4
VOC
—
±20.0
mA
Contiguous pin DC injection current—regional limit sum
of 16 contiguous pins
IICont
-25
25
mA
Output Voltage Range (normal push-pull mode)
VOUT
Pin Group 1, 2
-0.3
4.0
V
VOUTOD
Pin Group 1
-0.3
5.5
V
VOUTOD_RE
Pin Group 2
-0.3
4.0
V
Output clamp current, per
Output Voltage Range (open drain mode)
RESET Output Voltage Range
SET
Ambient Temperature
TA
V temperature
-40
105
°C
Junction Temperature
Tj
V temperature
-40
115
°C
-55
150
°C
Storage Temperature Range (Extended Industrial)
TSTG
1. Default Mode
• Pin Group 1: GPIO, TDI, TDO, TMS, TCK
• Pin Group 2: RESET
• Pin Group 3: ADC and Comparator Analog Inputs
• Pin Group 4: XTAL, EXTAL
2. Continuous clamp current
3. All 5 volt tolerant digital I/O pins are internally clamped to VSS through a ESD protection diode. There is no diode
connection to VDD. If VIN greater than VDIO_MIN (= VSS–0.3 V) is observed, then there is no need to provide current
limiting resistors at the pads. If this limit cannot be observed, then a current limiting resistor is required.
4. I/O is configured as push-pull mode.
7 General
7.1 General characteristics
The device is fabricated in high-density, low-power CMOS with 5 V–tolerant TTLcompatible digital inputs, except for the RESET pin which is 3.3V only. The term “5 V–
tolerant” refers to the capability of an I/O pin, built on a 3.3 V–compatible process
technology, to withstand a voltage up to 5.5 V without damaging the device.
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
27
General
5 V–tolerant I/O is desirable because many systems have a mixture of devices designed
for 3.3 V and 5 V power supplies. In such systems, a bus may carry both 3.3 V– and 5 V–
compatible I/O voltage levels (a standard 3.3 V I/O is designed to receive a maximum
voltage of 3.3 V ± 10% during normal operation without causing damage). This 5 V–
tolerant capability therefore offers the power savings of 3.3 V I/O levels combined with
the ability to receive 5 V levels without damage.
Absolute maximum ratings in Table 5 are stress ratings only, and functional operation at
the maximum is not guaranteed. Stress beyond these ratings may affect device reliability
or cause permanent damage to the device.
Unless otherwise stated, all specifications within this chapter apply to the temperature
range specified in Table 5 over the following supply ranges: VSS=VSSA=0V,
VDD=VDDA=3.0V to 3.6V, CL≤50 pF, fOP=50MHz.
CAUTION
This device contains protective circuitry to guard against
damage due to high static voltage or electrical fields. However,
normal precautions are advised to avoid application of any
voltages higher than maximum-rated voltages to this highimpedance circuit. Reliability of operation is enhanced if
unused inputs are tied to an appropriate voltage level.
7.2 AC electrical characteristics
Tests are conducted using the input levels specified in Table 8. Unless otherwise
specified, propagation delays are measured from the 50% to the 50% point, and rise and
fall times are measured between the 10% and 90% points, as shown in Figure 3.
VIH
Input Signal
Low
High
90%
50%
10%
Midpoint1
Fall Time
VIL
Rise Time
The midpoint is VIL + (VIH – VIL)/2.
Figure 3. Input signal measurement references
Figure 4 shows the definitions of the following signal states:
• Active state, when a bus or signal is driven, and enters a low impedance state
• Tri-stated, when a bus or signal is placed in a high impedance state
• Data Valid state, when a signal level has reached VOL or VOH
• Data Invalid state, when a signal level is in transition between VOL and VOH
MC56F826xx, Rev. 0, 08/2018
28
NXP Semiconductors
General
Data1 Valid
Data2 Valid
Data1
Data3 Valid
Data2
Data3
Data
Tri-stated
Data Invalid State
Data Active
Data Active
Figure 4. Signal states
7.3 Nonswitching electrical specifications
7.3.1 Voltage and current operating requirements
This section includes information about recommended operating conditions.
NOTE
Recommended VDD ramp rate is less than 200 ms.
Table 6. Recommended Operating Conditions (VREFLx=0V, VSSA=0V, VSS=0V)
Characteristic
Supply voltage
ADC (Cyclic) Reference Voltage High
Symbol
Notes1
Min
Typ
Max
Unit
VDD, VDDA
2.7
3.3
3.6
V
VREFHA
VDDA-0.6
VDDA
V
VREFHB
Voltage difference VDD to VDDA
ΔVDD
-0.1
0
0.1
Voltage difference VSS to VSSA
ΔVSS
-0.1
0
0.1
V
5.5
V
VDD
V
Input Voltage High (digital inputs)
RESET Voltage High
Input Voltage Low (digital inputs)
Oscillator Input Voltage High
VIH
Pin Group 1
0.7 x VDD
VIH_RESET
Pin Group 2
0.7 x VDD
—
V
VIL
Pin Groups 1, 2
0.35 x VDD
V
VIHOSC
Pin Group 4
2.0
VDD + 0.3
V
VILOSC
Pin Group 4
-0.3
0.8
V
IOH
Pin Group 1
—
-2
mA
Pin Group 1
—
-9
Pin Groups 1, 2
—
2
Pin Groups 1, 2
—
9
XTAL driven by an external clock source
Oscillator Input Voltage Low
Output Source Current High (at VOH min.)
• Programmed for low drive strength
• Programmed for high drive strength
Output Source Current Low (at VOL max.)2, 3
• Programmed for low drive strength
• Programmed for high drive strength
IOL
mA
1. Default Mode
• Pin Group 1: GPIO, TDI, TDO, TMS, TCK
• Pin Group 2: RESET
• Pin Group 3: ADC and Comparator Analog Inputs
• Pin Group 4: XTAL, EXTAL
2. Total IO sink current and total IO source current are limited to 75 mA each
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
29
General
3. Contiguous pin DC injection current of regional limit—including sum of negative injection currents or sum of positive
injection currents of 16 contiguous pins—is 25 mA.
7.3.2 LVD and POR operating requirements
Table 7. PMC Low-Voltage Detection (LVD) and Power-On Reset (POR) Parameters
Characteristic
POR Assert
Symbol
Voltage1
Min
Typ
Max
Unit
POR
2.0
V
POR
2.7
V
LVI_2p7 Threshold Voltage
2.73
V
LVI_2p2 Threshold Voltage
2.23
V
POR Release
Voltage2
1. During 3.3-volt VDD power supply ramp down
2. During 3.3-volt VDD power supply ramp up (gated by LVI_2p7)
7.3.3 Voltage and current operating behaviors
The following table provides information about power supply requirements and I/O pin
characteristics.
Table 8. DC Electrical Characteristics at Recommended Operating Conditions
Symbol
Notes 1
Min
Typ
Max
Unit
Test Conditions
Output Voltage High
VOH
Pin Group 1
VDD - 0.5
—
—
V
IOH = IOHmax
Output Voltage Low
VOL
Pin Groups
1, 2
—
—
0.5
V
IOL = IOLmax
IIH
Pin Group 1
—
0
+/- 2.5
µA
VIN = 2.4 V to 5.5 V
Characteristic
Digital Input Current High
Pin Group 2
pull-up enabled or
disabled
Comparator Input Current
High
Oscillator Input Current
High
Digital Input Current Low
2, 3
VIN = 2.4 V to VDD
IIHC
Pin Group 3
—
0
+/- 2
µA
VIN = VDDA
IIHOSC
Pin Group 3
—
0
+/- 2
µA
VIN = VDDA
IIL
Pin Groups
1, 2
—
0
+/- 0.5
µA
VIN = 0V
RPull-Up
20
—
50
kΩ
—
RPull-Down
20
—
50
kΩ
—
pull-up disabled
Internal Pull-Up
Resistance
Internal Pull-Down
Resistance
Comparator Input Current
Low
Oscillator Input Current
Low
IILC
Pin Group 3
—
0
+/- 2
µA
VIN = 0V
IILOSC
Pin Group 3
—
0
+/- 2
µA
VIN = 0V
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
30
NXP Semiconductors
General
Table 8. DC Electrical Characteristics at Recommended Operating Conditions (continued)
Characteristic
Output Current 2, 3
Symbol
Notes 1
Min
Typ
Max
Unit
Test Conditions
IOZ
Pin Groups
1, 2
—
0
+/- 1
µA
—
VHYS
Pin Groups
1, 2
0.06 × VDD
—
—
V
—
High Impedance State
Schmitt Trigger Input
Hysteresis
1. Default Mode
• Pin Group 1: GPIO, TDI, TDO, TMS, TCK
• Pin Group 2: RESET
• Pin Group 3: ADC and Comparator Analog Inputs
• Pin Group 4: XTAL, EXTAL
2. See the following figure "IIN/IOZ vs. VIN (typical; pull-up disabled)" .
3. To minimize the excessive leakage current from digital pin, input signal should not stay between 1.1 V and 0.7 × VDD for
prolonged time.
Figure 5. IIN/IOZ vs. VIN (typical; pull-up disabled) (design simulation)
7.3.4 Power mode transition operating behaviors
Parameters listed are guaranteed by design.
NOTE
All address and data buses described here are internal.
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
31
General
Table 9. Reset, stop, wait, and interrupt timing
Characteristic
Symbol
Typical Min
Typical
Max
Unit
See
Figure
Minimum RESET Assertion Duration
tRA
161
—
ns
—
RESET deassertion to First Address Fetch
tRDA
865 x TOSC + 8 x T
ns
—
tIF
361.3
ns
—
Delay from Interrupt Assertion to Fetch of first
instruction (exiting Stop)
570.9
1. If the RESET pin filter is enabled by setting the RST_FLT bit in the SIM_CTRL register to 1, the minimum pulse assertion
must be greater than 21 ns. Recommended a capacitor of up to 0.1 µF on RESET.
NOTE
In Table 9, T = system clock cycle and TOSC = oscillator clock
cycle. For an operating frequency of 50MHz, T=20 ns. At 4
MHz (used coming out of reset and stop modes), T=250 ns.
Table 10. Power mode transition behavior
Symbol
TPOR
Notes1
Description
Min
Max
Unit
After a POR event, the amount of delay from when VDD reaches
2.7 V to when the first instruction executes (over the operating
temperature range).
199
225
µs
STOP mode to RUN mode
6.79
7.27.31
µs
2
LPS mode to LPRUN mode
240.9
551
µs
3
VLPS mode to VLPRUN mode
1424
1459
µs
4
WAIT mode to RUN mode
0.570
0.620
µs
5
LPWAIT mode to LPRUN mode
237.2
554
µs
3
VLPWAIT mode to VLPRUN mode
1413
1500
µs
4
1. Wakeup times are measured from GPIO toggle for wakeup till GPIO toggle at the wakeup interrupt subroutine from
respective stop/wait mode.
2. Clock configuration: CPU clock=4 MHz. System clock source is 8 MHz IRC in normal mode.
3. CPU clock = 200 KHz and 8 MHz IRC on standby. Exit by an interrupt on PORTC GPIO.
4. Using 64 KHz external clock; CPU Clock = 32KHz. Exit by an interrupt on PortC GPIO.
5. Clock configuration: CPU and system clocks= 100 MHz. Bus Clock = 50 MHz. .Exit by interrupt on PORTC GPIO
7.3.5 Power consumption operating behaviors
Table 11. Current Consumption (mA)
Mode
RUN1
Maximum
Frequency
100 MHz
Conditions
• 100 MHz Core
• 50 MHz Peripheral clock
• Regulators are in full regulation
Typical at
3.3 V, 25°C
Maximum
at 3.6 V,
105°C
IDD1
IDDA
IDD1
IDDA
38.1
9.9
53.5
13.2
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
32
NXP Semiconductors
General
Table 11. Current Consumption (mA) (continued)
Mode
Maximum
Frequency
Conditions
Typical at
3.3 V, 25°C
Maximum
at 3.6 V,
105°C
IDD1
IDDA
IDD1
IDDA
• Relaxation Oscillator on
• PLL powered on
• Continuous MAC instructions with fetches from Program
Flash
• All peripheral modules enabled. TMRs and SCIs using 1X
peripheral clock
• ADC/all 6-bit DACs) powered on and clocked
• Comparator powered on
RUN2
50 MHz
•
•
•
•
•
50 MHz Core and Peripheral clock
Regulators are in full regulation
Relaxation Oscillator on
PLL powered on
Continuous MAC instructions with fetches from Program
Flash
• All peripheral modules enabled. TMRs and SCIs using 1X
peripheral clock
• ADC/all 6-bit DACs) powered on and clocked
• Comparator powered on
27.6
9.9
43.5
13.2
WAIT
50 MHz
•
•
•
•
•
•
•
•
50 MHz Core and Peripheral clock
Regulators are in full regulation
Relaxation Oscillator on
PLL powered on
Processor Core in WAIT state
All Peripheral modules enabled.
TMRs and SCIs using 1X Clock
ADC/all 6-bit DACs), Comparator powered off
24.0
—
41.3
—
STOP
4 MHz
•
•
•
•
•
•
•
4 MHz Device Clock
Regulators are in full regulation
Relaxation Oscillator on
PLL powered off
Processor Core in STOP state
All peripheral module and core clocks are off
ADC/Comparator powered off
6.3
—
19.4
—
LPRUN
(LsRUN)
2 MHz
• 200 kHz Device Clock from Relaxation Oscillator's (ROSC)
low speed clock
• ROSC in standby mode
• Regulators are in standby
• PLL disabled
• Repeat NOP instructions
• All peripheral modules enabled, except cyclic ADCs. all 6bit DACs enabled.
• Simple loop with running from platform instruction buffer
2.8
3.1
11.1
4.0
LPWAIT
(LsWAIT)
2 MHz
• 200 kHz Device Clock from Relaxation Oscillator's (ROSC)
low speed clock
• ROSC in standby mode
• Regulators are in standby
• PLL disabled
• All peripheral modules enabled, except cyclic ADCs. all 6bit DACs enabled.1
• Processor core in wait mode
2.7
3.1
11.1
4.0
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
33
General
Table 11. Current Consumption (mA) (continued)
Mode
Maximum
Frequency
Conditions
Typical at
3.3 V, 25°C
Maximum
at 3.6 V,
105°C
IDD1
IDDA
IDD1
IDDA
• 200 kHz Device Clock from Relaxation Oscillator's (ROSC)
low speed clock
• ROSC in standby mode
• Regulators are in standby
• PLL disabled
• Only PITs and COP enabled; other peripheral modules
disabled and clocks gated off1
• Processor core in stop mode
1.2
—
9.1
—
LPSTOP
(LsSTOP)
2 MHz
VLPRUN
200 kHz
•
•
•
•
•
•
•
•
•
32 kHz Device Clock
Clocked by a 64 kHz external clock source
Oscillator in power down
All ROSCs disabled
Large regulator is in standby
Small regulator is disabled
PLL disabled
Repeat NOP instructions
All peripheral modules, except COP and EWM, disabled
and clocks gated off
• Simple loop running from platform instruction buffer
0.7
—
7.5
—
VLPWAIT
200 kHz
•
•
•
•
•
•
•
•
32 kHz Device Clock
Clocked by a 64 kHz external clock source
Oscillator in power down
All ROSCs disabled
Large regulator is in standby
Small regulator is disabled
PLL disabled
All peripheral modules, except COP, disabled and clocks
gated off
• Processor core in wait mode
0.7
—
7.5
—
VLPSTOP
200 kHz
•
•
•
•
•
•
•
•
0.7
—
7.5
—
32 kHz Device Clock
Clocked by a 64 kHz external clock source
Oscillator in power down
All ROSCs disabled
Large regulator is in standby.
Small regulator is disabled.
PLL disabled
All peripheral modules, except COP, disabled and clocks
gated off
• Processor core in stop mode
1. No output switching, all ports configured as inputs, all inputs low, no DC loads.
7.3.6 Designing with radiated emissions in mind
To find application notes that provide guidance on designing your system to minimize
interference from radiated emissions:
1. Go to www.nxp.com.
MC56F826xx, Rev. 0, 08/2018
34
NXP Semiconductors
General
2. Perform a keyword search for “EMC design.”
7.3.7 Capacitance attributes
Table 12. Capacitance attributes
Description
Symbol
Min.
Typ.
Max.
Unit
CIN
—
10
—
pF
COUT
—
10
—
pF
Input capacitance
Output capacitance
7.4 Switching specifications
7.4.1 Device clock specifications
Table 13. Device clock specifications
Symbol
Description
Min.
Max.
Unit
0.001
100
MHz
0
100
—
50
Notes
Normal run mode
fSYSCLK
fBUS
Device (system and core) clock frequency
• using relaxation oscillator
• using external clock source
Bus clock
MHz
7.4.2 General switching timing
Table 14. Switching timing
Symbol
Description
Min
GPIO pin interrupt pulse width1
1.5
Max
Unit
Notes
IP Bus
Clock
Cycles
Synchronous path
Port rise and fall time (high drive strength), Slew disabled 2.7
≤ VDD ≤ 3.6V.
5.5
15.1
ns
Port rise and fall time (high drive strength), Slew enabled 2.7
≤ VDD ≤ 3.6V.
1.5
6.8
ns
Port rise and fall time (low drive strength). Slew disabled . 2.7
≤ VDD ≤ 3.6V
8.2
17.8
ns
Port rise and fall time (low drive strength). Slew enabled . 2.7
≤ VDD ≤ 3.6V
3.2
9.2
ns
2
3
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
35
General
1. Applies to a pin only when it is configured as GPIO and configured to cause an interrupt by appropriately programming
GPIOn_IPOLR and GPIOn_IENR.
2. 75 pF load
3. 15 pF load
7.5 Thermal specifications
7.5.1 Thermal operating requirements
Table 15. Thermal operating requirements
Symbol
Description
Min
Max
Unit
TJ
Die junction temperature
V
–40
115
°C
TA
Ambient temperature
V
–40
105
°C
7.5.2 Thermal attributes
This section provides information about operating temperature range, power dissipation,
and package thermal resistance. Power dissipation on I/O pins is usually small compared
to the power dissipation in on-chip logic and voltage regulator circuits, and it is userdetermined rather than being controlled by the MCU design. To account for PI/O in power
calculations, determine the difference between actual pin voltage and VSS or VDD and
multiply by the pin current for each I/O pin. Except in cases of unusually high pin current
(heavy loads), the difference between pin voltage and VSS or VDD is very small.
See Thermal design considerations for more detail on thermal design considerations.
Board type
Symbol
Description
32 LQFP
48 LQFP
Unit
Notes
Single-layer
(1s)
RθJA
Thermal
83
resistance,
junction to
ambient (natural
convection)
70
°C/W
,
Four-layer
(2s2p)
RθJA
Thermal
55
resistance,
junction to
ambient (natural
convection)
46
°C/W
1,
Single-layer
(1s)
RθJMA
Thermal
70
resistance,
junction to
ambient (200 ft./
min. air speed)
57
°C/W
1,2
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
36
NXP Semiconductors
Peripheral operating requirements and behaviors
Board type
Symbol
Description
32 LQFP
48 LQFP
Unit
Four-layer
(2s2p)
RθJMA
Thermal
49
resistance,
junction to
ambient (200 ft./
min. air speed)
39
°C/W
—
RθJB
Thermal
resistance,
junction to
board
31
23
°C/W
—
RθJC
Thermal
resistance,
junction to case
22
17
°C/W
—
ΨJT
Thermal
5
characterization
parameter,
junction to
package top
outside center
(natural
convection)
3
°C/W
Notes
1,2
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site
(board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board
thermal resistance.
2. Determined according to JEDEC Standard JESD51-6, Integrated Circuits Thermal Test Method Environmental Conditions
—Forced Convection (Moving Air) with the board horizontal.
8 Peripheral operating requirements and behaviors
8.1 Core modules
8.1.1 JTAG timing
Table 16. JTAG timing
Characteristic
Symbol
Min
Max
Unit
See
Figure
TCK frequency of operation
fOP
DC
SYS_CLK/ 8
MHz
Figure 6
TCK clock pulse width
tPW
50
—
ns
Figure 6
TMS, TDI data set-up time
tDS
5
—
ns
Figure 7
TMS, TDI data hold time
tDH
5
—
ns
Figure 7
TCK low to TDO data valid
tDV
—
30
ns
Figure 7
TCK low to TDO tri-state
tTS
—
30
ns
Figure 7
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
37
System modules
1/fOP
VIH
TCK
(Input)
tPW
tPW
VM
VM
VIL
VM = VIL + (VIH – VIL)/2
Figure 6. Test clock input timing diagram
TCK
(Input)
tDS
TDI
TMS
(Input)
tDH
Input Data Valid
tDV
TDO
(Output)
Output Data Valid
tTS
TDO
(Output)
Figure 7. Test access port timing diagram
8.2 System modules
8.2.1 Voltage regulator specifications
The voltage regulator supplies approximately 1.2 V to the MC56F82xxx’s core logic. For
proper operations, the voltage regulator requires an external 2.2 µF capacitor on each
VCAP pin. Ceramic and tantalum capacitors tend to provide better performance
tolerances. The output voltage can be measured directly on the VCAP pin. The
specifications for this regulator are shown in Table 17.
Table 17. Regulator 1.2 V parameters
Characteristic
Symbol
Min
Typ
Max
Unit
Output Voltage1
VCAP
—
1.22
—
V
Short Circuit Current2
ISS
—
600
—
mA
Short Circuit Tolerance (VCAP shorted to ground)
TRSC
—
—
30
Minutes
1. Value is after trim
2. Guaranteed by design
MC56F826xx, Rev. 0, 08/2018
38
NXP Semiconductors
System modules
Table 18. Bandgap electrical specifications
Characteristic
Symbol
Min
Typ
Max
Unit
Reference Voltage (after trim)
VREF
—
1.21
—
V
8.3 Clock modules
8.3.1 External clock operation timing
Parameters listed are guaranteed by design.
Table 19. External clock operation timing requirements
Characteristic
Frequency of operation (external clock
driver)1
Symbol
Min
Typ
Max
Unit
—
50
MHz
fosc
—
tPW
8
trise
—
—
1
ns
tfall
—
—
1
ns
Input high voltage overdrive by an external clock
Vih
0.85VDD
—
—
V
Input low voltage overdrive by an external clock
Vil
—
—
0.3VDD
V
Clock pulse width2
External clock input rise time3
External clock input fall
1.
2.
3.
4.
time4
ns
See Figure 1 for detail on using the recommended connection of an external clock driver.
The chip may not function if the high or low pulse width is smaller than 6.25 ns.
External clock input rise time is measured from 10% to 90%.
External clock input fall time is measured from 90% to 10%.
External
Clock
90%
50%
10%
tPW
tfall
tPW
trise
VIH
90%
50%
10%
VIL
Note: The midpoint is VIL + (VIH – VIL)/2.
Figure 8. External clock timing
8.3.2 Phase-Locked Loop timing
Table 20. Phase-Locked Loop timing
Characteristic
PLL input reference
PLL output
frequency1
frequency2
PLL lock
time3
Symbol
Min
Typ
Max
Unit
fref
8
8
16
MHz
fop
200
—
400
MHz
tplls
35.5
73.2
µs
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
39
System modules
Table 20. Phase-Locked Loop timing (continued)
Characteristic
Symbol
Min
Typ
Max
Unit
Allowed Duty Cycle of input reference
tdc
40
50
60
%
1. An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work correctly.
The PLL is optimized for 8 MHz input.
2. The frequency of the core system clock cannot exceed 100 MHz.
3. This is the time required after the PLL is enabled to ensure reliable operation.
8.3.3 External crystal or resonator requirement
Table 21. Crystal or resonator requirement
Characteristic
Symbol
Min
Typ
Max
Unit
Frequency of operation
fXOSC
4
8
16
MHz
8.3.4 Relaxation Oscillator Timing
Table 22. Relaxation Oscillator Electrical Specifications
Characteristic
8 MHz Output
Symbol
Min
Typ
Max
Unit
0°C to 105°C
7.84
8
8.16
MHz
-40°C to 105°C
7.76
8
8.24
MHz
-40°C to 105°C
—
405
—
kHz
0°C to 105°C
+/-1.5
+/-2
%
-40°C to 105°C
+/-1.5
+/-3
%
200
206
%
0°C to 85°C
+/-1.5
+/-2
%
-40°C to 105°C
+/-1.5
+/-3
%
Frequency1
Run Mode
Standby Mode (IRC
trimmed @ 8 MHz)
8 MHz Frequency Variation over 25°C
RUN Mode
200 kHz Output
Frequency1
RUN Mode
-40°C to 105°C
194
200 kHz Output Frequency Variation over 25°C
RUN Mode
Stabilization Time
8 MHz
output2
200 kHz
tstab
output3
Output Duty Cycle
48
0.12
µs
10
µs
50
52
%
1. Frequency after factory trim
2. Standby to run mode transition
3. Power down to run mode transition
MC56F826xx, Rev. 0, 08/2018
40
NXP Semiconductors
System modules
Figure 9. Relaxation Oscillator Temperature Variation (Typical) After Trim (Preliminary)
8.4 Memories and memory interfaces
8.4.1 Flash electrical specifications
This section describes the electrical characteristics of the flash memory module.
8.4.1.1
Flash timing specifications — program and erase
The following specifications represent the amount of time the internal charge pumps are
active and do not include command overhead.
Table 23. NVM program/erase timing specifications
Symbol
Description
thvpgm4
Longword Program high-voltage time
Min.
Typ.
Max.
Unit
Notes
—
7.5
18
μs
—
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
41
System modules
Table 23. NVM program/erase timing specifications (continued)
Symbol
Description
Min.
Typ.
Max.
Unit
Notes
thversscr
Sector Erase high-voltage time
—
13
113
ms
1
thversall
Erase All high-voltage time
—
52
452
ms
1
1. Maximum time based on expectations at cycling end-of-life.
8.4.1.2
Flash timing specifications — commands
Table 24. Flash command timing specifications
Symbol
Description
Min.
Typ.
Max.
Unit
Notes
trd1sec1k
Read 1s Section execution time (flash sector)
—
—
60
μs
1
tpgmchk
Program Check execution time
—
—
45
μs
1
trdrsrc
Read Resource execution time
—
—
30
μs
1
tpgm4
Program Longword execution time
—
65
145
μs
—
tersscr
Erase Flash Sector execution time
—
14
114
ms
2
trd1all
Read 1s All Blocks execution time
—
—
0.9
ms
1
trdonce
Read Once execution time
—
—
25
μs
1
Program Once execution time
—
65
—
μs
—
tersall
Erase All Blocks execution time
—
70
575
ms
2
tvfykey
Verify Backdoor Access Key execution time
—
—
30
μs
1
tpgmonce
1. Assumes 25 MHz flash clock frequency.
2. Maximum times for erase parameters based on expectations at cycling end-of-life.
8.4.1.3
Flash high voltage current behaviors
Table 25. Flash high voltage current behaviors
Symbol
Description
IDD_PGM
IDD_ERS
8.4.1.4
Symbol
Min.
Typ.
Max.
Unit
Average current adder during high voltage
flash programming operation
—
2.5
6.0
mA
Average current adder during high voltage
flash erase operation
—
1.5
4.0
mA
Reliability specifications
Table 26. NVM reliability specifications
Description
Min.
Typ.1
Max.
Unit
Notes
Program Flash
tnvmretp10k Data retention after up to 10 K cycles
5
50
—
years
—
tnvmretp1k
Data retention after up to 1 K cycles
20
100
—
years
—
nnvmcycp
Cycling endurance
10 K
50 K
—
cycles
2
MC56F826xx, Rev. 0, 08/2018
42
NXP Semiconductors
System modules
1. Typical data retention values are based on measured response accelerated at high temperature and derated to a constant
25 °C use profile. Engineering Bulletin EB618 does not apply to this technology. Typical endurance defined in Engineering
Bulletin EB619.
2. Cycling endurance represents number of program/erase cycles at –40 °C ≤ Tj ≤ 125 °C.
8.5 Analog
8.5.1 12-bit Cyclic Analog-to-Digital Converter (ADC) Parameters
Table 27. 12-bit ADC Electrical Specifications
Characteristic
Symbol
Min
Typ
Max
Unit
VDDA
3
3.3
3.6
V
Vrefhx
VDDA-0.6
VDDA
V
fADCCLK
0.1
10
MHz
Recommended Operating Conditions
Supply Voltage1
VREFH (in external reference mode)
ADC Conversion
Conversion
Clock2
Range3
RAD
Fully Differential
– (VREFH – VREFL)
Single Ended/Unipolar
Input Voltage Range (per input)4
VREFH – VREFL
VREFH
VREFL
VADIN
External Reference
V
VREFL
VREFH
0
VDDA
Internal Reference
V
Timing and Power
Conversion Time5
tADC
8
ADC Clock
Cycles
ADC Power-Up Time (from adc_pdn)
tADPU
13
ADC Clock
Cycles
ADC RUN Current (per ADC block)
IADRUN
1.8
mA
ADC Powerdown Current (adc_pdn
enabled)
IADPWRDWN
0.1
µA
IVREFH
190
225
µA
Integral non-Linearity6
INL
+/- 1.5
+/- 2.2
LSB7
Differential non-Linearity6
DNL
+/- 0.5
+/- 0.8
LSB7
VREFH Current (in external mode)
Accuracy (DC or Absolute)
Monotonicity
Offset8
GUARANTEED
VOFFSET
mV
+/- 8
Fully Differential
+/- 12
Single Ended/Unipolar
Gain Error
EGAIN
0.996 to1.004
Signal to Noise Ratio
SNR
66
dB
Total Harmonic Distortion
THD
75
dB
AC
0.990 to 1.010
Specifications9
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
43
System modules
Table 27. 12-bit ADC Electrical Specifications (continued)
Characteristic
Symbol
Min
Typ
Max
Unit
Spurious Free Dynamic Range
SFDR
77
dB
Signal to Noise plus Distortion
SINAD
66
dB
Effective Number of Bits
ENOB
—
bits
Gain = 1x (Fully Differential/Unipolar)
10.6
Gain = 2x (Fully Differential/Unipolar)
—
Gain = 4x (Fully Differential/Unipolar)
10.3
Gain = 1x (Single Ended)
10.6
Gain = 2x (Single Ended)
10.4
Gain = 4x (Single Ended)
10.2
Variation across
channels10
0.1
ADC Inputs
Input Leakage Current
IIN
1
nA
Temperature sensor slope
TSLOPE
1.7
mV/°C
Temperature sensor voltage at 25 °C
VTEMP25
0.82
V
Disturbance
Input Injection Current 11
Channel to Channel
Memory
Crosstalk13
Input Capacitance
Crosstalk12
IINJ
+/-3
mA
ISOXTLK
-82
dB
MEMXTLK
-71
dB
CADI
4.8
pF
Sampling Capacitor
1. The ADC functions up to VDDA = 2.7 V. When VDDA is below 3.0 V, ADC specifications are not guaranteed
2. ADC clock duty cycle is 45% ~ 55%
3. Conversion range is defined for x1 gain setting. For x2 and x4 the range is 1/2 and 1/4, respectively.
4. In unipolar mode, positive input must be ensured to be always greater than negative input.
5. First conversion takes 10 clock cycles.
6. INL/DNL is measured from VIN = VREFL to VIN = VREFH using Histogram method at x1 gain setting
7. Least Significant Bit = 0.806 mV at 3.3 V VDDA, x1 gain Setting
8. Offset measured at 2048 code
9. Measured converting a 1 kHz input full scale sine wave
10. When code runs from internal RAM
11. The current that can be injected into or sourced from an unselected ADC input without affecting the performance of the
ADC
12. Any off-channel with 50 kHz full-scale input to the channel being sampled with DC input (isolation crosstalk)
13. From a previously sampled channel with 50 kHz full-scale input to the channel being sampled with DC input (memory
crosstalk).
8.5.1.1
Equivalent circuit for ADC inputs
The following figure shows the ADC input circuit during sample and hold. S1 and S2 are
always opened/closed at non-overlapping phases, and both S1 and S2 are dependent on
the ADC clock frequency. The following equation gives equivalent input impedance
when the input is selected.
MC56F826xx, Rev. 0, 08/2018
44
NXP Semiconductors
System modules
1
-12
(ADC ClockRate) x
4.8x10
+ 100 ohm + 50 ohm
C1
Analog Input
1
50 ESD
Resistor
Channel Mux
equivalent resistance
100Ohms
S1
C1
S1
S/H
S1
2
C1
S2
S1
S2
(VREFHx - VREFLx ) / 2
C1
1. Parasitic capacitance due to package, pin-to-pin and pin-to-package base coupling =
1.8pF
2. Parasitic capacitance due to the chip bond pad, ESD protection devices and signal
routing = 2.04pF
3. S1 and S2 switch phases are non-overlapping and depend on the ADC clock
frequency
S1
S2
Figure 10. Equivalent circuit for A/D loading
8.5.2 CMP32and 6-bit DAC electrical specifications
Freescale Semicond
Table 28. Comparator and 6-bit DAC electrical specifications
Symbol
Description
Min.
Typ.
Max.
Unit
VDD
Supply voltage
2.7
—
3.6
V
IDDHS
Supply current, High-speed mode (EN=1, PMODE=1)
—
300
—
μA
IDDLS
Supply current, low-speed mode (EN=1, PMODE=0)
—
36
—
μA
VAIN
Analog input voltage
VSS
—
VDD
V
VAIO
Analog input offset voltage
—
—
20
mV
• CR0[HYSTCTR] = 001
—
5
13
mV
• CR0[HYSTCTR] = 01
—
25
48
mV
VH
Analog comparator hysteresis
Table continues on the next page...
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
45
System modules
Table 28. Comparator and 6-bit DAC electrical specifications (continued)
Symbol
Description
Min.
Typ.
Max.
Unit
• CR0[HYSTCTR] =
102
—
55
105
mV
• CR0[HYSTCTR] =
112
—
80
148
mV
VCMPOh
Output high
VDD – 0.5
—
—
V
VCMPOl
Output low
—
—
0.5
V
tDHS
Propagation delay, high-speed mode (EN=1,
PMODE=1)
—
25
50
ns
tDLS
Propagation delay, low-speed mode (EN=1,
PMODE=0)3
—
60
200
ns
Analog comparator initialization delay4
—
40
—
μs
6-bit DAC current adder (enabled)
—
7
—
μA
VDDA
—
VDD
V
IDAC6b
6-bit DAC reference inputs, Vin1 and Vin2
There are two reference input options selectable (via
VRSEL control bit). The reference options must fall
within this range.
INL
6-bit DAC integral non-linearity
–0.5
—
0.5
LSB5
DNL
6-bit DAC differential non-linearity
–0.3
—
0.3
LSB
1.
2.
3.
4.
Measured with input voltage range limited to 0 to VDD
Measured with input voltage range limited to 0.7≤Vin≤VDD-0.8
Input voltage range: 0.1VDD≤Vin≤0.9VDD, step = ±100mV, across all temperature. Does not include PCB and PAD delay.
Comparator initialization delay is defined as the time between software writes to change control inputs (Writes to DACEN,
VRSEL, PSEL, MSEL, VOSEL) and the comparator output settling to a stable level.
5. 1 LSB = Vreference/64
MC56F826xx, Rev. 0, 08/2018
46
NXP Semiconductors
System modules
0.08
0.07
CMP Hystereris (V)
0.06
HYSTCTR
Setting
0.05
00
0.04
01
10
11
0.03
0.02
0.01
0
0.1
0.4
0.7
1
1.3
1.6
1.9
2.2
2.5
2.8
3.1
Vin level (V)
Figure 11. Typical hysteresis vs. Vin level (VDD = 3.3 V, PMODE = 0)
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
47
Timer
0.18
0.16
0.14
CMP Hysteresis (V)
0.12
HYSTCTR
Setting
0.1
00
01
10
11
0.08
0.06
0.04
0.02
0
0.1
0.4
0.7
1.3
1.6
1.9
Vin level (V)
1
2.2
2.5
2.8
3.1
Figure 12. Typical hysteresis vs. Vin level (VDD = 3.3 V, PMODE = 1)
8.6 Timer
8.6.1 Quad Timer timing
Parameters listed are guaranteed by design.
Table 29. Timer timing
Characteristic
Symbol
Min1
Max
Unit
See Figure
Timer input period
PIN
2T + 6
—
ns
Figure 13
Timer input high/low period
PINHL
1T + 3
—
ns
Figure 13
Timer output period
POUT
2T-2
—
ns
Figure 13
Timer output high/low period
POUTHL
1T-2
—
ns
Figure 13
1. T = clock cycle. For 100 MHz operation, T = 10 ns.
MC56F826xx, Rev. 0, 08/2018
48
NXP Semiconductors
Timer
Timer Inputs
PIN
PINHL
PINHL
POUT
POUTHL
POUTHL
Timer Outputs
Figure 13. Timer timing
8.7 Communication interfaces
8.7.1 Queued Serial Communication Interface (SCI) timing
Parameters listed are guaranteed by design.
Table 30. SCI timing
Characteristic
Symbol
Min
Max
Unit
See Figure
BR
—
(fMAX/16)
Mbit/s
—
RXD pulse width
RXDPW
0.965/BR
1.04/BR
μs
Figure 14
TXD pulse width
TXDPW
0.965/BR
1.04/BR
μs
Figure 15
-14
14
%
—
Baud
rate1
LIN Slave Mode
Deviation of slave node clock from nominal FTOL_UNSYNCH
clock rate before synchronization
Deviation of slave node clock relative to
the master node clock after
synchronization
FTOL_SYNCH
-2
2
%
—
Minimum break character length
TBREAK
13
—
Master
node bit
periods
—
11
—
Slave node
bit periods
—
1. fMAX is the frequency of operation of the SCI clock in MHz, which can be selected as the bus clock (max.50 MHz
depending on part number) or 2x bus clock (max. 100 MHz) for the devices.
RXD
SCI receive
data pin
(Input)
RXDPW
Figure 14. RXD pulse width
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
49
Design Considerations
TXD
SCI transmit
data pin
(output)
TXDPW
Figure 15. TXD pulse width
9 Design Considerations
9.1 Thermal design considerations
An estimate of the chip junction temperature (TJ) can be obtained from the equation:
TJ = TA + (RΘJA x PD)
Where,
TA = Ambient temperature for the package (°C)
RΘJA = Junction-to-ambient thermal resistance (°C/W)
PD = Power dissipation in the package (W)
The junction-to-ambient thermal resistance is an industry-standard value that provides a
quick and easy estimation of thermal performance. Unfortunately, there are two values in
common usage: the value determined on a single-layer board and the value obtained on a
board with two planes. For packages such as the PBGA, these values can be different by
a factor of two. Which TJ value is closer to the application depends on the power
dissipated by other components on the board.
• The TJ value obtained on a single layer board is appropriate for a tightly packed
printed circuit board.
• The TJ value obtained on a board with the internal planes is usually appropriate if the
board has low-power dissipation and if the components are well separated.
When a heat sink is used, the thermal resistance is expressed as the sum of a junction-tocase thermal resistance and a case-to-ambient thermal resistance:
RΘJA = RΘJC + RΘCA
Where,
RΘJA = Package junction-to-ambient thermal resistance (°C/W)
RΘJC = Package junction-to-case thermal resistance (°C/W)
RΘCA = Package case-to-ambient thermal resistance (°C/W)
MC56F826xx, Rev. 0, 08/2018
50
NXP Semiconductors
Design Considerations
RΘJC is device related and cannot be adjusted. You control the thermal environment to
change the case to ambient thermal resistance, RΘCA. For instance, you can change the
size of the heat sink, the air flow around the device, the interface material, the mounting
arrangement on printed circuit board, or change the thermal dissipation on the printed
circuit board surrounding the device.
To determine the junction temperature of the device in the application when heat
sinks are not used, the thermal characterization parameter (YJT) can be used to
determine the junction temperature with a measurement of the temperature at the top
center of the package case using the following equation:
TJ = TT + (ΨJT x PD)
Where,
TT = Thermocouple temperature on top of package (°C/W)
ΨJT = hermal characterization parameter (°C/W)
PD = Power dissipation in package (W)
The thermal characterization parameter is measured per JESD51–2 specification using a
40-gauge type T thermocouple epoxied to the top center of the package case. The
thermocouple should be positioned so that the thermocouple junction rests on the
package. A small amount of epoxy is placed over the thermocouple junction and over
about 1 mm of wire extending from the junction. The thermocouple wire is placed flat
against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
To determine the junction temperature of the device in the application when heat
sinks are used, the junction temperature is determined from a thermocouple inserted at
the interface between the case of the package and the interface material. A clearance slot
or hole is normally required in the heat sink. Minimizing the size of the clearance is
important to minimize the change in thermal performance caused by removing part of the
thermal interface to the heat sink. Because of the experimental difficulties with this
technique, many engineers measure the heat sink temperature and then back-calculate the
case temperature using a separate measurement of the thermal resistance of the interface.
From this case temperature, the junction temperature is determined from the junction-tocase thermal resistance.
9.2 Electrical design considerations
CAUTION
This device contains protective circuitry to guard against
damage due to high static voltage or electrical fields. However,
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
51
Design Considerations
take normal precautions to avoid application of any voltages
higher than maximum-rated voltages to this high-impedance
circuit. Reliability of operation is enhanced if unused inputs are
tied to an appropriate voltage level.
Use the following list of considerations to assure correct operation of the device:
• Provide a low-impedance path from the board power supply to each VDD pin on the
device and from the board ground to each VSS (GND) pin.
• The minimum bypass requirement is to place 0.01–0.1 µF capacitors positioned as
near as possible to the package supply pins. The recommended bypass configuration
is to place one bypass capacitor on each of the VDD/VSS pairs, including VDDA/VSSA.
Ceramic and tantalum capacitors tend to provide better tolerances.
• Ensure that capacitor leads and associated printed circuit traces that connect to the
chip VDD and VSS (GND) pins are as short as possible.
• Bypass the VDD and VSS with approximately 100 µF, plus the number of 0.1 µF
ceramic capacitors.
• PCB trace lengths should be minimal for high-frequency signals.
• Consider all device loads as well as parasitic capacitance due to PCB traces when
calculating capacitance. This is especially critical in systems with higher capacitive
loads that could create higher transient currents in the VDD and VSS circuits.
• Take special care to minimize noise levels on the VREF, VDDA, and VSSA pins.
• Using separate power planes for VDD and VDDA and separate ground planes for VSS
and VSSA are recommended. Connect the separate analog and digital power and
ground planes as near as possible to power supply outputs. If an analog circuit and
digital circuit are powered by the same power supply, then connect a small inductor
or ferrite bead in serial with VDDA. Traces of VSS and VSSA should be shorted
together.
• Physically separate analog components from noisy digital components by ground
planes. Do not place an analog trace in parallel with digital traces. Place an analog
ground trace around an analog signal trace to isolate it from digital traces.
• Because the flash memory is programmed through the JTAG/EOnCE port, SCI, or
I2C, the designer should provide an interface to this port if in-circuit flash
programming is desired.
• If desired, connect an external RC circuit to the RESET pin. The resistor value
should be in the range of 4.7 kΩ–10 kΩ; the capacitor value should be in the range of
0.22 µF–4.7 µF.
• Configuring the RESET pin to GPIO output in normal operation in a high-noise
environment may help to improve the performance of noise transient immunity.
• Add a 2.2 kΩ external pullup on the TMS pin of the JTAG port to keep EOnCE in a
restate during normal operation if JTAG converter is not present.
MC56F826xx, Rev. 0, 08/2018
52
NXP Semiconductors
Design Considerations
• During reset and after reset but before I/O initialization, all I/O pins are at tri-state.
• To eliminate PCB trace impedance effect, each ADC input should have a no less than
33 pF 10Ω RC filter.
9.3 Power-on Reset design considerations
9.3.1 Improper power-up sequence between VDD/VSS and VDDA/
VSSA:
It is recommended that VDD be kept within 100 mV of VDDA at all times, including
power ramp-up and ramp-down. Failure to keep VDDA within 100 mV of VDDA may
cause a leakage current through the substrate, between the VDD and VDDA pad cells.
This leakage current could prevent operation of the device after it powers up. The voltage
difference between VDD and VDDA must be limited to below 0.3 V at all times, to avoid
permanent damage to the part (See Table 5). Also see Table 6.
9.3.2 Unnecessary protection circuit:
In many circuit designs, it is a general practice to add external clamping diodes on each
analog input pin; see diode D1 and D2 in Figure 16, to prevent the surge voltage from
damaging the analog input.
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
53
Design Considerations
Reg1
DC
DC
200V ~300V
Reg3
12V
C6
+
DC
C5
Reg2
DC
3.3V
DC
C4
+
3.3V
DC
C2
+
R6
R3
C1
VDDA
R5
R4
C3
VDD
MC56F8xxxx
R2
D1
C8
ADC_IN
R1
D2
RESET
D1 and D2 are unnecessary,
because all analog
inputs already have the
internal current injection
protection circuit.
VSSA
VSS
+
C7
Figure 16. Protection Circuit Example
MC56F8xxxx DSC uses the 5V tolerance I/O. When the pin is configured to digital input,
it can accept 5V input. See Table 5. When the pin is configured to analog input, the
internal integrated current injection protection circuit is enabled. The current injection
protection circuit performs the same functions as external clamp diode D1 and D2 in
Figure 16. As long as the source or sink current for each analog pin is less than 3 mA,
then there is no damage to the device. See Table 27. Therefore, D1 and D2 clamping
diodes are not recommended to be used.
9.3.3 Heavy capacitive load on power supply output:
In some applications, the low cost DC/DC converter may not regulate the output voltage
well before it reaches the regulation point, which is roughly around 2.5V to 2.7V.
However, the MC56F8xxxx DSC will exit power-on reset at around 2.3V. If the
initialization code enables the PLL to run the DSC at full speed right after reset, then the
high current will be pulled by DSC from the supply, which can cause the supply voltage
to drop below the operation voltage; see the captured graph (Figure 17). This can cause
the DSC fail to start up.
MC56F826xx, Rev. 0, 08/2018
54
NXP Semiconductors
Obtaining package dimensions
Figure 17. Supply Voltage Drop
A recommended initialization sequence during power-up is:
1. After POR is released, run a few hundred NOP instructions from the internal
relaxation oscillator; this gives time for the supply voltage to stabilize.
2. Configure the peripherals (except the ADC) to the desired settings; the ADC should
stay in low power mode.
3. Power up the PLL.
4. After the PLL locks, switch the clock from PLL prescale to postscale.
5. Configure the ADC.
10 Obtaining package dimensions
Package dimensions are provided in package drawings.
To find a package drawing, go to nxp.com and perform a keyword search for the
drawing's document number:
Drawing for package
Document number to be used
32LQFP
98ASH70029A
48-pin LQFP
98ASH00962A
11 Pinout
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
55
Pinout
11.1 Signal Multiplexing and Pin Assignments
The following table shows the signals available on each pin and the locations of these
pins on the devices supported by this document. The SIM's GPS registers are responsible
for selecting which ALT functionality is available on most pins.
NOTE
• The RESETB pin is a 3.3 V pin only.
• If the GPIOC1 pin is used as GPIO, the XOSC should be
powered down.
• Not all CMPD pins are available on 48 LQFP, 32 LQFP
packages.
48
32
LQFP LQFP
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
—
19
GPIOF2
GPIOF2
XB_OUT6
—
20
GPIOF3
GPIOF3
XB_OUT7
1
1
TCK
TCK
GPIOD2
2
2
RESETB
RESETB
GPIOD4
3
—
GPIOC0
GPIOC0
EXTAL
4
—
GPIOC1
GPIOC1
XTAL
5
3
GPIOC2
GPIOC2
TXD0
XB_OUT11
XB_IN2
CLKO0
6
4
GPIOC3
GPIOC3
TA0
CMPA_O
RXD0
CLKIN1
7
5
GPIOC4
GPIOC4
TA1
CMPB_O
XB_IN6
EWM_OUT_B
8
—
GPIOA4
GPIOA4
ANA4&CMPD_IN0
9
6
GPIOA0
GPIOA0
ANA0&CMPA_IN3
10
7
GPIOA1
GPIOA1
ANA1&CMPA_IN0
11
8
GPIOA2
GPIOA2
ANA2&VREFHA&CMPA_
IN1
12
—
GPIOA3
GPIOA3
ANA3&VREFLA&CMPA_
IN2
13
—
GPIOC5
GPIOC5
14
—
GPIOB4
GPIOB4
15
9
VDDA
VDDA
16
10
VSSA
VSSA
17
11
GPIOB0
GPIOB0
ANB0&CMPB_IN3
18
12
GPIOB1
GPIOB1
ANB1&CMPB_IN0
19
—
VCAP
VCAP
20
13
GPIOB2
GPIOB2
ANB2&VERFHB&CMPC_
IN3
21
—
GPIOB3
GPIOB3
ANB3&VREFLB&CMPC_
IN0
22
14
VSS
VSS
23
15
GPIOC6
GPIOC6
CLKIN0
CMPC_O
XB_IN7
ANB4&CMPC_IN1
TA2
XB_IN3
CMP_REF
MC56F826xx, Rev. 0, 08/2018
56
NXP Semiconductors
Pinout
48
32
LQFP LQFP
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
24
—
GPIOC7
GPIOC7
TXD0
XB_IN8
25
16
GPIOC8
GPIOC8
RXD0
XB_IN9
XB_OUT6
26
17
GPIOC9
GPIOC9
XB_IN4
TXD0
XB_OUT8
27
18
GPIOC10
GPIOC10
XB_IN5
28
—
GPIOF0
GPIOF0
29
—
GPIOC11
GPIOC11
TXD1
30
—
GPIOC12
GPIOC12
RXD1
31
—
VSS
VSS
32
—
VDD
VDD
33
21
GPIOE0
GPIOE0
PWM_0B
34
22
GPIOE1
GPIOE1
PWM_0A
35
23
GPIOE2
GPIOE2
PWM_1B
36
24
GPIOE3
GPIOE3
PWM_1A
37
—
GPIOC13
GPIOC13
TA3
XB_IN6
EWM_OUT_B
38
—
GPIOF1
GPIOF1
CLKO1
XB_IN7
CMPD_O
39
25
GPIOE4
GPIOE4
PWM_2B
XB_IN2
40
26
GPIOE5
GPIOE5
PWM_2A
XB_IN3
41
—
GPIOC14
GPIOC14
XB_OUT4
PWM_FAULT4
42
—
GPIOC15
GPIOC15
XB_OUT5
PWM_FAULT5
43
27
VCAP
VCAP
44
28
VDD
VDD
45
29
VSS
VSS
46
30
TDO
TDO
GPIOD1
47
31
TMS
TMS
GPIOD3
48
32
TDI
TDI
GPIOD0
XB_OUT9
XB_IN6
11.2 Pinout diagrams
The following diagrams show pinouts for the packages. For each pin, the diagrams show
the default function. However, many signals may be multiplexed onto a single pin.
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
57
TDI
TMS
TDO
VSS
VDD
VCAP
GPIOC15
GPIOC14
GPIOE5
GPIOE4
GPIOF1
GPIOC13
48
47
46
45
44
43
42
41
40
39
38
37
Pinout
GPIOC4
7
30
GPIOC12
GPIOA4
8
29
GPIOC11
GPIOA0
9
28
GPIOF0
GPIOA1
10
27
GPIOC10
GPIOA2
11
26
GPIOC9
GPIOA3
12
25
GPIOC8
24
VSS
GPIOC7
31
23
6
GPIOC6
GPIOC3
22
VDD
VSS
32
21
5
GPIOB3
GPIOC2
20
GPIOE0
GPIOB2
33
19
4
VCAP
GPIOC1
18
GPIOE1
GPIOB1
34
17
3
GPIOB0
GPIOC0
16
GPIOE2
VSSA
35
15
2
VDDA
RESETB
14
GPIOE3
GPIOB4
36
13
1
GPIOC5
TCK
Figure 18. 48-pin LQFP
NOTE
The RESETB pin is a 3.3 V pin only.
MC56F826xx, Rev. 0, 08/2018
58
NXP Semiconductors
TDI
TMS
TDO
VSS
VDD
VCAP
GPIOE5
GPIOE4
32
31
30
29
28
27
26
25
Product documentation
4
21
GPIOE0
GPIOC4
5
20
GPIOF3
GPIOA0
6
19
GPIOF2
GPIOA1
7
18
GPIOC10
GPIOA2
8
17
GPIOC9
VSSA
9
VDDA
16
GPIOC3
GPIOC8
GPIOE1
15
22
GPIOC6
3
14
GPIOC2
VSS
GPIOE2
13
23
GPIOB2
2
12
RESETB
GPIOB1
GPIOE3
11
24
GPIOB0
1
10
TCK
Figure 19. 32-pin LQFP
NOTE
The RESETB pin is a 3.3 V pin only.
12 Product documentation
The documents listed in Table 31 are required for a complete description and to
successfully design using the device. Documentation is available from local NXP
distributors, NXP sales offices, or online at www.nxp.com.
Table 31. Device documentation
Topic
DSP56800E/DSP56800EX
Reference Manual
Description
Detailed description of the 56800EX family architecture, 32-bit
digital signal controller core processor, and the instruction set
Document Number
DSP56800ERM
MC56F826xx Reference Manual
Detailed functional description and programming model
MC56F826XXRM
MC56F826xx Data Sheet
Electrical and timing specifications, pin descriptions, and
package information (this document)
MC56F826XXDS
MC56F82xxx Errata
Details any chip issues that might be present
MC56F82xxx_Errata
MC56F826xx, Rev. 0, 08/2018
NXP Semiconductors
59
How to Reach Us:
Home Page:
nxp.com
Web Support:
nxp.com/support
Information in this document is provided solely to enable system and software implementers to use
NXP products. There are no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits based on the information in this document. NXP reserves the right to
make changes without further notice to any products herein.
NXP makes no warranty, representation, or guarantee regarding the suitability of its products for any
particular purpose, nor does NXP assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without limitation
consequential or incidental damages. "Typical" parameters that may be provided in NXP data sheets
and/or specifications can and do vary in different applications, and actual performance may vary over
time. All operating parameters, including "typicals," must be validated for each customer application
by customer's technical experts. NXP does not convey any license under its patent rights nor the
rights of others. NXP sells products pursuant to standard terms and conditions of sale, which can be
found at the following address: nxp.com/SalesTermsandConditions.
While NXP has implemented advanced security features, all products may be subject to unidentified
vulnerabilities. Customers are responsible for the design and operation of their applications and
products to reduce the effect of these vulnerabilities on customer's applications and products, and
NXP accepts no liability for any vulnerability that is discovered. Customers should implement
appropriate design and operating safeguards to minimize the risks associated with their applications
and products.
NXP, the NXP logo, NXP SECURE CONNECTIONS FOR A SMARTER WORLD, COOLFLUX,
EMBRACE, GREENCHIP, HITAG, I2C BUS, ICODE, JCOP, LIFE VIBES, MIFARE, MIFARE
CLASSIC, MIFARE DESFire, MIFARE PLUS, MIFARE FLEX, MANTIS, MIFARE ULTRALIGHT,
MIFARE4MOBILE, MIGLO, NTAG, ROADLINK, SMARTLX, SMARTMX, STARPLUG, TOPFET,
TRENCHMOS, UCODE, Freescale, the Freescale logo, AltiVec, C‑5, CodeTEST, CodeWarrior,
ColdFire, ColdFire+, C‑Ware, the Energy Efficient Solutions logo, Kinetis, Layerscape, MagniV,
mobileGT, PEG, PowerQUICC, Processor Expert, QorIQ, QorIQ Qonverge, Ready Play, SafeAssure,
the SafeAssure logo, StarCore, Symphony, VortiQa, Vybrid, Airfast, BeeKit, BeeStack, CoreNet,
Flexis, MXC, Platform in a Package, QUICC Engine, SMARTMOS, Tower, TurboLink, and UMEMS
are trademarks of NXP B.V. All other product or service names are the property of their respective
owners. AMBA, Arm, Arm7, Arm7TDMI, Arm9, Arm11, Artisan, big.LITTLE, Cordio, CoreLink,
CoreSight, Cortex, DesignStart, DynamIQ, Jazelle, Keil, Mali, Mbed, Mbed Enabled, NEON, POP,
RealView, SecurCore, Socrates, Thumb, TrustZone, ULINK, ULINK2, ULINK-ME, ULINK-PLUS,
ULINKpro, µVision, Versatile are trademarks or registered trademarks of Arm Limited (or its
subsidiaries) in the US and/or elsewhere. The related technology may be protected by any or all of
patents, copyrights, designs and trade secrets. All rights reserved. Oracle and Java are registered
trademarks of Oracle and/or its affiliates. The Power Architecture and Power.org word marks and the
Power and Power.org logos and related marks are trademarks and service marks licensed by
Power.org.
© 2018 NXP B.V.
Document Number MC56F826XXDS
Revision 0, 08/2018