MCZ33199EF

Freescale Semiconductor Technical Data Document Number: MC33199 Rev. 4.0, 10/2006 33199 The MC33199 is a serial interface circuit used in diagnostic applications. It is the interface between the microcontroller and the special K and L lines of the ISO diagnostic port. The MC33199 has been designed to meet the «Diagnosis System ISO9141» specification. The device has a bi-directional bus K line driver, fully protected against short circuits and over temperature. It also includes the L line receiver, used during the wake up sequence in the ISO transmission. The MC33199 has a unique feature which allow transmission Baud rate up to 200kBaud. LIN, ISO-9141 J-1850 PHYSICAL INTERFACES D SUFFIX EF SUFFIX (PB-FREE) PLASTIC PACKAGE 98ASB42565B 14 PIN SOIC Features • Electrically Compatible with Specification “Diagnosis System ISO9141” • Transmission speed up to 200kBaud • Internal Voltage Reference Generator for Line Comparator Thresholds • TXD, RXD and LO pins are 5V CMOS Compatible • High Current Capability of DIA pin (K line) • Short Circuit Protection for the K Line Input • Over Temperature Shutdown with Hysteresis • Large Operating Range of Driver Supply Voltage • Large Operating Temperature Range • ESD Protected pins • Pb-Free Packaging Designated by Suffix Code EF ORDERING INFORMATION Device MC33199D MCZ33199EF/R2 Temperature Range (TA) Package -40°C to 125°C 14 SOIC VBAT VDD 33199 VDD VS LO L SCIRXD RXD I1 SCITXD TXD DIA MCU I/O VCC GND Figure 1. Simplified Application Diagram Freescale Semiconductor, Inc. reserves the right to change the detail specifications, as may be required, to permit improvements in the design of its products. © Freescale Semiconductor, Inc., 2007. All rights reserved. ISO L-LINE (BUS) ISO K-LINE ARCHIVE INFORMATION ARCHIVE INFORMATION Automotive ISO 9141 Serial Link Driver INTERNAL BLOCK DIAGRAM INTERNAL BLOCK DIAGRAM VCC 33199 VS Reference Generator REF-OUT LO Protection L + – C2 I1 Source REF-IN-L ARCHIVE INFORMATION RXD I1 VCC – + C1 DIA Thermal Shutdown TXD Driver GND Current Limit Figure 2. 33199 Simplified Internal Block Diagram 33199 2 Analog Integrated Circuit Device Data Freescale Semiconductor ARCHIVE INFORMATION REF-IN-K PIN CONNECTIONS PIN CONNECTIONS 1 14 REF-OUT REF-IN-L 2 13 VS REF-IN-K 3 12 L LO 4 11 I1 RXD 5 10 GND TXD 6 9 DIA NC 7 8 NC ARCHIVE INFORMATION ARCHIVE INFORMATION 33199 VCC Figure 3. 33199 Pin Connections Table 1. Pin Definitions A functional description of each pin can be found in the Functional Pin Description section, beginning on page 12. Pin Number Pin Name Definition 1 VCC 2 REF-IN-L Input reference for C2 comparator. 3 REF-IN-K Input reference for C1 comparator. 4 LO 5 RXD Open drain output of the data on BUS. A recessive bus = a logic [1], a dominant bus = logic [0]. An external pullup is required. 6 TXD Data input here will appear on the BUS pin. A logic [0] will assert the bus, a logic [1] will make the bus go to the recessive state. 7, 8 NC No internal connection to these pins. 9 DIA Provides a battery-level logic signal. 10 GND Electrical Common Ground and Heat removal. A good thermal path will also reduce the die temperature. 11 I1 Power input. An external diode is needed for reverse battery protection. 12 L The external bus load resistor connects here to prevent bus pullup in the event of loss of module ground. 13 VS 14 REF-OUT 5V typical power supply pin. typical supply current is less than 1.5mA This pin control Sleep Mode, Transmit Level, and Speed. It has a weak pulldown. This pin connects to the bus through external components. Internal reference voltage generator output pin. 33199 Analog Integrated Circuit Device Data Freescale Semiconductor 3 ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS Table 2. Maximum Ratings All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Ratings Symbol Value Unit DC Voltage Range VS 0.5 to + 40 Transient Pulse (2) VPULSE 2 to + 40 VCC 0.3 to + 6.0 V - 0.5 TO + 38 V ELECTRICAL RATINGS (1) V VCC Supply DC Voltage Range DIA and L Pins (2) DC Voltage Range Transient Pulse (clamped by internal diode) DC Source Current DIA Low Level Sink Current TXD DC Voltage Range -2 V - 50 mA INT. LIMIT mA -0.3 TO VCC +0.3 V REF-IN DC Voltage Range V VS < VCC -0.3 TO VCC VS > VCC -0.3 TO VS ESD Voltage Capability VESD +/-2000 V TSTG 55 to + 150 °C TJ 40 to + 150 °C RTJA 180 C/W PD 250 mW TPPRT Note 4. °C THERMAL RATINGS Storage Temperature Operating Junction Temperature Thermal Resistance, Junction to air Max Power Dissipation (@ TA=105 °C) Peak Package Reflow Temperature During Reflow (3), (4) Notes 1. The device is compatible with Specification: “Diagnosis System ISO9141” 2. See the test Circuit (Figure 26). Transient test pulse according to ISO76371 and DIN 40839, highest test levels 3. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may cause malfunction or permanent damage to the device. 4. Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow Temperature and Moisture Sensitivity Levels (MSL), Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e. MC33xxxD enter 33xxx), and review parametrics. 33199 4 Analog Integrated Circuit Device Data Freescale Semiconductor ARCHIVE INFORMATION ARCHIVE INFORMATION VS Supply Pin ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 3. Static Electrical Characteristics Characteristics noted under conditions VCC from 4.5V to 5.5V, VS from 4.5V to 20V unless otherwise note. Typical values reflect approximate mean at 25°C, nominal VCC and VS, at time of device characterization. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Characteristic Symbol Min VCC 4.5 ICC 0.5 Typ Max Unit 5.5 V 1.5 V VCC PIN 1 VCC Supply Voltage Range VCC Supply Current (6) 1.0 REF-IN-L & REF-IN-K Input Voltage Range: VINREF V for 0