Freescale Semiconductor
Advance Information
Document Number: MMPF0200Z
Rev. 2.0, 11/2014
12 Channel Configurable Power
Management Integrated Circuit
PF0200Z
The PF0200Z Power Management Integrated Circuit (PMIC) provides
a highly programmable/ configurable architecture, with fully integrated
power devices and minimal external components. With up to four buck
converters, one boost regulator, six linear regulators, RTC supply, and
coin-cell charger, the PF0200Z can provide power for a complete
system, including applications processors, memory, and system
peripherals, in a wide range of applications. With on-chip One Time
Programmable (OTP) memory, the PF0200Z is available in preprogrammed standard versions, or non-programmed to support
custom programming. The PF0200Z is especially suited to the
i.MX 6SoloLite, i.MX 6Solo and i.MX 6DualLite versions of the i.MX 6
family of devices and is supported by full system level reference
designs, and pre-programmed versions of the device. This device is
powered by SMARTMOS technology.
Features:
• Three to four buck converters, depending on configuration
• Boost regulator to 5.0 V output
• Six general purpose linear regulators
• Programmable output voltage, sequence, and timing
• OTP (One Time Programmable) memory for device configuration
• Coin cell charger and RTC supply
• DDR termination reference voltage
• Power control logic with processor interface and event detection
• I2C control
• Individually programmable ON, OFF, and Standby modes
PF0200Z
Power Management
ES SUFFIX (WF-TYPE)
56 QFN 8X8
98ASA00589D
Applications
• GPS
• Auto infotainment
• Heads up display (HUD)
• Rear displays
• Digital instrumentation cluster (DIC)
i.MX6X
VREFDDR
DDR MEMORY
INTERFACE
DDR Memory
SW3A/B
Processor Core
Voltages
SW1A/B
SW2
SWBST
SD-MMC/
NAND Mem.
SATA
HDD
SATA - FLASH
NAND - NOR
Interfaces
Control Signals
Parallel control/GPIOS
I2C Communication
I2C Communication
VGEN1
VGEN2
VGEN3
VGEN4
Camera
External AMP
Microphones
Speakers
Audio
Codec
Sensors
Camera
GPS
MIPI
uPCIe
WAM
GPS
MIPI
HDMI
LDVS Display
VGEN5
LICELL
Charger
COINCELL
USB
Ethernet
CAN
VGEN6
Main Supply
Cluster/HUD
Front USB
POD
Rear Seat
Infotaiment
Figure 1. Simplified Application Diagram
* This document contains certain information on a new product.
Specifications and information herein are subject to change without notice.
© Freescale Semiconductor, Inc., 2014. All rights reserved.
Rear USB
POD
Table of Contents
1
Orderable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
Internal Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3
Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Pinout Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2.1 Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3.1 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3.2 Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.1 Power Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.2 Control Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6
Functional Block Requirements and Behaviors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1.1 Device Start-up Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1.2 One Time Programmability (OTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.1.3 OTP Prototyping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1.4 Reading OTP Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1.5 Programming OTP Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2 16 MHz and 32 kHz Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2.1 Clock adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.3 Bias and References Block Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.3.1 Internal Core Voltage References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.3.2 VREFDDR Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.4 Power Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.4.1 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.4.2 State Machine Flow Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.4.3 Power Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.4.4 Buck Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.4.5 Boost Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.4.6 LDO Regulators Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.4.7 VSNVS LDO/Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
6.5 Control Interface I2C Block Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6.5.1 I2C Device ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6.5.2 I2C Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6.5.3 Interrupt Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.5.4 Interrupt Bit Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.5.5 Specific Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
6.5.6 Register Bitmap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
7
Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
7.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
7.1.1 Application Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
7.1.2 Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
7.2 PF0200Z Layout Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
7.2.1 General Board Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
PF0200Z
2
Analog Integrated Circuit Device Data
Freescale Semiconductor
7.2.2 Component Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
7.2.3 General Routing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
7.2.4 Parallel Routing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
7.2.5 Switching Regulator Layout Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
7.3 Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
7.3.1 Rating Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
7.3.2 Estimation of Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
8
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
9
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
8.1 Packaging Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
3
Orderable Parts
1
Orderable Parts
The PF0200Z is available with both pre-programmed and non-programmed OTP memory configurations. The non-programmed
device uses “NP” as the programming code. Contact your Freescale representative for more details.
Table 1. Orderable Part Variations
Part Number
MMPF0200NPAZES
Temperature (TA)
Package
Programming
Qualification Tier
Notes
-40 to 85 °C
56 QFN 8x8 mm - 0.5 mm pitch
WF-Type QFN (wettable flank)
NP
Automotive
(1) (2)
Notes
1. For Tape and Reel add an R2 suffix to the part number.
2. For programming details see Table 8.
PF0200Z
4
Analog Integrated Circuit Device Data
Freescale Semiconductor
Internal Block Diagram
2
Internal Block Diagram
PF0200Z
VGEN1
100 mA
VIN1
VGEN1
SW1FB
SW1A/B
Single/Dual
2500 mA
Buck
VGEN2
250 mA
VGEN2
VIN2
VGEN3
VGEN3
100 mA
VGEN4
VGEN4
350 mA
SW2
1500 mA
Buck
VGEN5
100 mA
VGEN5
O/P
Drive
SW1AIN
SW1ALX
SW1BLX
SW1BIN
SW1VSSSNS
Core Control logic
VIN3
O/P
Drive
O/P
Drive
SW2LX
SW2IN
SW2IN
SW2FB
GNDREF1
Initialization State Machine
VGEN6
200 mA
VGEN6
Supplies
Control
OTP
SW3AFB
VDDOTP
SW3A/B
Single Phase
2500 mA
Buck
CONTROL
I2C
Interface
VDDIO
SCL
SDA
O/P
Drive
O/P
Drive
DVS CONTROL
I2C Register
map
VCOREREF
VCORE
SW3BIN
SW3VSSSNS
Trim-In-Package
Reference
Generation
SW3BLX
SW3BFB
DVS Control
VCOREDIG
SW3AIN
SW3ALX
SWBST
600 mA
Boost
Clocks and
resets
O/P
Drive
SWBSTLX
SWBSTIN
SWBSTFB
GNDREF
VREFDDR
VINREFDDR
Clocks
32 kHz and 16 MHz
VHALF
VIN
Li Cell
Charger
Best
of
Supply
LICELL
RSVD6
RSVD5
RSVD4
RSVD3
RSVD2
RSVD1
INTB
SDWNB
STANDBY
RESETBMCU
ICTEST
PWRON
VSNVS
VSNVS
Figure 2. Simplified Internal Block Diagram
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
5
Pin Connections
Pinout Diagram
SDA
VCOREREF
VCOREDIG
VIN
VCORE
GNDREF
VDDOTP
SWBSTLX
SWBSTIN
SWBSTFB
VSNVS
Pinout Diagram
SCL
3.1
VDDIO
Pin Connections
PWRON
3
56
55
54
53
52
51
50
49
48
47
46
45
44
43
INTB
1
42
LICELL
SDWNB
2
41
VGEN6
RESETBMCU
3
40
VIN3
STANDBY
4
39
VGEN5
ICTEST
5
38
SW3AFB
SW1FB
6
37
SW3AIN
SW1AIN
7
36
SW3ALX
SW1ALX
8
35
SW3BLX
SW1BLX
9
34
SW3BIN
SW1BIN
10
33
SW3BFB
RSVD1
11
32
SW3VSSSNS
RSVD2
12
31
VREFDDR
RSVD3
13
30
VINREFDDR
SW1VSSSNS
14
29
VHALF
15
16
17
18
19
20
21
22
23
24
25
26
27
28
GNDREF1
VGEN1
VIN1
VGEN2
RSVD4
RSVD5
RSVD6
SW2LX
SW2IN
SW2IN
SW2FB
VGEN3
VIN2
VGEN4
EP
Figure 3. Pinout Diagram
PF0200Z
6
Analog Integrated Circuit Device Data
Freescale Semiconductor
Pin Connections
Pin Definitions
3.2
Pin Definitions
Table 2. PF0200Z Pin Definitions
Pin Number
Pin Name
Pin
Function
Max Rating
Type
1
INTB
O
3.6 V
Digital
Open drain interrupt signal to processor
2
SDWNB
O
3.6 V
Digital
Open drain signal to indicate an imminent system shutdown
3
RESETBMCU
O
3.6 V
Digital
Open drain reset output to processor. Alternatively can be used
as a Power Good output.
4
STANDBY
I
3.6 V
Digital
Standby input signal from processor
5
ICTEST
I
7.5 V
Digital/
Analog
Reserved pin. Connect to GND in application.
6
SW1FB (4)
I
3.6 V
Analog
Output voltage feedback for SW1A/B. Route this trace separately
from the high-current path and terminate at the output
capacitance.
7
SW1AIN (4)
I
4.8 V
Analog
Input to SW1A regulator. Bypass with at least a 4.7 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
8
SW1ALX (4)
O
4.8 V
Analog
Regulator 1A switch node connection
9
SW1BLX (4)
O
4.8 V
Analog
Regulator 1B switch node connection
10
SW1BIN (4)
I
4.8 V
Analog
Input to SW1B regulator. Bypass with at least a 4.7 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
11
RSVD1
-
-
Reserved
Reserved for pin to pin compatibility. Internally connected. Leave
this pin unconnected.
12
RSVD2
-
-
Reserved
Reserved for pin to pin compatibility. Connect this pin to VIN.
13
RSVD3
-
-
Reserved
Reserved for pin to pin compatibility. Internally connected. Leave
this pin unconnected.
14
SW1VSSSNS
GND
-
GND
Ground reference for regulator SW1AB. It is connected externally
to GNDREF through a board ground plane.
15
GNDREF1
GND
-
GND
Ground reference for regulator SW2. It is connected externally to
GNDREF, via board ground plane.
16
VGEN1
O
2.5 V
Analog
VGEN1 regulator output, Bypass with a 2.2 F ceramic output
capacitor.
17
VIN1
I
3.6 V
Analog
VGEN1, 2 input supply. Bypass with a 1.0 F decoupling
capacitor as close to the pin as possible.
18
VGEN2
O
2.5 V
Analog
VGEN2 regulator output, Bypass with a 4.7 F ceramic output
capacitor.
19
RSVD4
-
-
Reserved
Reserved for pin to pin compatibility. Internally connected. Leave
this pin unconnected.
20
RSVD5
-
-
Reserved
Reserved for pin to pin compatibility. Connect this pin to VIN
21
RSVD6
-
-
Reserved
Reserved for pin to pin compatibility. Internally connected. Leave
this pin unconnected.
22
SW2LX (4)
O
4.8 V
Analog
Regulator 2 switch node connection
23
SW2IN
(4)
I
4.8 V
Analog
24
SW2IN (4)
I
4.8 V
Analog
Input to SW2 regulator. Connect pin 23 together with pin 24 and
bypass with at least a 4.7 F ceramic capacitor and a 0.1 F
decoupling capacitor as close to these pins as possible.
Definition
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
7
Pin Connections
Pin Definitions
Table 2. PF0200Z Pin Definitions (continued)
Pin Number
Pin Name
Pin
Function
Max Rating
Type
25
SW2FB (4)
I
3.6 V
Analog
Output voltage feedback for SW2. Route this trace separately
from the high-current path and terminate at the output
capacitance.
26
VGEN3
O
3.6 V
Analog
VGEN3 regulator output. Bypass with a 2.2 F ceramic output
capacitor.
27
VIN2
I
3.6 V
Analog
VGEN3,4 input. Bypass with a 1.0 F decoupling capacitor as
close to the pin as possible.
28
VGEN4
O
3.6 V
Analog
VGEN4 regulator output, Bypass with a 4.7 F ceramic output
capacitor.
29
VHALF
I
3.6 V
Analog
Half supply reference for VREFDDR
30
VINREFDDR
I
3.6 V
Analog
VREFDDR regulator input. Bypass with at least 1.0 F decoupling
capacitor as close to the pin as possible.
31
VREFDDR
O
3.6 V
Analog
VREFDDR regulator output
32
SW3VSSSNS
GND
-
GND
Ground reference for the SW3 regulator. Connect to GNDREF
externally via the board ground plane.
33
SW3BFB (4)
I
3.6 V
Analog
Output voltage feedback for SW3B. Route this trace separately
from the high-current path and terminate at the output
capacitance.
34
SW3BIN (4)
I
4.8 V
Analog
Input to SW3B regulator. Bypass with at least a 4.7 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
35
SW3BLX (4)
O
4.8 V
Analog
Regulator 3B switch node connection
36
SW3ALX
(4)
O
4.8 V
Analog
Regulator 3A switch node connection
37
SW3AIN (4)
I
4.8 V
Analog
Input to SW3A regulator. Bypass with at least a 4.7 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
38
SW3AFB (4)
I
3.6 V
Analog
Output voltage feedback for SW3A. Route this trace separately
from the high-current path and terminate at the output
capacitance.
39
VGEN5
O
3.6 V
Analog
VGEN5 regulator output. Bypass with a 2.2 F ceramic output
capacitor.
40
VIN3
I
4.8 V
Analog
VGEN5, 6 input. Bypass with a 1.0 F decoupling capacitor as
close to the pin as possible.
41
VGEN6
O
3.6 V
Analog
VGEN6 regulator output. By pass with a 2.2 F ceramic output
capacitor.
42
LICELL
I/O
3.6 V
Analog
Coin cell supply input/output
43
VSNVS
O
3.6 V
Analog
LDO or coin cell output to processor
44
SWBSTFB (4)
I
5.5 V
Analog
Boost regulator feedback. Connect this pin to the output rail close
to the load. Keep this trace away from other noisy traces and
planes.
45
SWBSTIN (4)
I
4.8 V
Analog
Input to SWBST regulator. Bypass with at least a 2.2 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
46
SWBSTLX (4)
O
7.5 V
Analog
SWBST switch node connection
47
VDDOTP
I
10 V(3)
Digital &
Analog
Definition
Supply to program OTP fuses
PF0200Z
8
Analog Integrated Circuit Device Data
Freescale Semiconductor
Pin Connections
Pin Definitions
Table 2. PF0200Z Pin Definitions (continued)
Pin Number
Pin Name
Pin
Function
Max Rating
Type
48
GNDREF
GND
-
GND
49
VCORE
O
3.6 V
Analog
Analog Core supply
50
VIN
I
4.8 V
Analog
Main chip supply
51
VCOREDIG
O
1.5 V
Analog
Digital Core supply
52
VCOREREF
O
1.5 V
Analog
Main band gap reference
53
SDA
I/O
3.6 V
Digital
I2C data line (Open drain)
54
SCL
I
3.6 V
Digital
I2C clock
55
VDDIO
I
3.6 V
Analog
Supply for I2C bus. Bypass with 0.1 F decoupling capacitor as
close to the pin as possible.
56
PWRON
I
3.6 V
Digital
Power On/off from processor
-
EP
GND
-
GND
Expose pad. Functions as ground return for buck regulators. Tie
this pad to the inner and external ground planes through vias to
allow effective thermal dissipation.
Definition
Ground reference for the main band gap regulator.
Notes
3. 10 V Maximum voltage rating during OTP fuse programming. 7.5 V Maximum DC voltage rated otherwise.
4. Unused switching regulators should be connected as follow: Pins SWxLX and SWxFB should be unconnected and Pin SWxIN should
be connected to VIN with a 0.1 F bypass capacitor.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
General Product Characteristics
Absolute Maximum Ratings
4
General Product Characteristics
4.1
Absolute Maximum Ratings
Table 3. Absolute Maximum Ratings
All voltages are with respect to ground, unless otherwise noted. Exceeding these ratings may cause malfunction or permanent
damage to the device. The detailed maximum voltage rating per pin can be found in the pin list section.
Symbol
Description
Value
Unit
Main input supply voltage
-0.3 to 4.8
V
VDDOTP
OTP programming input supply voltage
-0.3 to 10
V
VLICELL
Coin cell voltage
-0.3 to 3.6
V
±2000
±500
V
ELECTRICAL RATINGS
VIN
VESD
ESD Ratings
Human Body Model(5)
Charge Device Model(5)
Notes
5. ESD testing is performed in accordance with the Human Body Model (HBM) (CZAP = 100 pF, RZAP = 1500 ), and the Charge Device
Model (CDM), Robotic (CZAP = 4.0 pF).
PF0200Z
10
Analog Integrated Circuit Device Data
Freescale Semiconductor
General Product Characteristics
Thermal Characteristics
4.2
Thermal Characteristics
Table 4. Thermal Ratings
Symbol
Description (Rating)
Min.
Max.
Unit
THERMAL RATINGS
TA
Ambient Operating Temperature Range
PF0200Z
-40
85
TJ
Operating Junction Temperature Range (6)
-40
125
C
Storage Temperature Range
-65
150
C
–
Note 8
C
Junction to Ambient (9)(10)(11)
Natural Convection
Four layer board (2s2p)
Eight layer board (2s6p)
–
–
28
15
Junction to Ambient (@200 ft/min)(9)(11)
Four layer board (2s2p)
–
22
Junction to Board(12)
–
10
°C/W
–
1.2
°C/W
–
2.0
°C/W
TST
TPPRT
Peak Package Reflow Temperature
(7)(8)
C
QFN56 THERMAL RESISTANCE AND PACKAGE DISSIPATION RATINGS
RJA
RJMA
RJB
RJCBOTTOM
JT
Junction to Case
Bottom(13)
Top(14)
Junction to Package
Natural Convection
°C/W
°C/W
Notes
6. Do not operate beyond 125 °C for extended periods of time. Operation above 150 °C may cause permanent damage to the IC. See
Table 5 for thermal protection features.
7. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may
cause a malfunction or permanent damage to the device.
8. Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow
Temperature and Moisture Sensitivity Levels (MSL), Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes
and enter the core ID to view all orderable parts (i.e. MC33xxxD enter 33xxx), and review parametrics.
9. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance.
10. The Board uses the JEDEC specifications for thermal testing (and simulation) JESD51-7 and JESD51-5.
11. Per JEDEC JESD51-6 with the board horizontal.
12. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top
surface of the board near the package.
13. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1).
14. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per
JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
General Product Characteristics
Electrical Characteristics
4.2.1
Power Dissipation
During operation, the temperature of the die should not exceed the operating junction temperature noted in Table 4. To optimize
the thermal management and to avoid overheating, the PF0200Z provides thermal protection. An internal comparator monitors
the die temperature. Interrupts THERM110I, THERM120I, THERM125I, and THERM130I will be generated when the respective
thresholds specified in Table 5 are crossed in either direction. The temperature range can be determined by reading the
THERMxxxS bits in register INTSENSE0.
In the event of excessive power dissipation, thermal protection circuitry will shut down the PF0200Z. This thermal protection will
act above the thermal protection threshold listed in Table 5. To avoid any unwanted power downs resulting from internal noise,
the protection is debounced for 8.0 ms. This protection should be considered as a fail-safe mechanism and therefore the system
should be configured such that this protection is not tripped under normal conditions.
Table 5. Thermal Protection Thresholds
Parameter
Min
Typ
Max
Units
Thermal 110 °C Threshold (THERM110)
100
110
120
°C
Thermal 120 °C Threshold (THERM120)
110
120
130
°C
Thermal 125 °C Threshold (THERM125)
115
125
135
°C
Thermal 130 °C Threshold (THERM130)
120
130
140
°C
Thermal Warning Hysteresis
2.0
–
4.0
°C
Thermal Protection Threshold
130
140
150
°C
4.3
Electrical Characteristics
4.3.1
General Specifications
Table 6. General PMIC Static Characteristics
TA = -40 to 85 °C, VIN = 2.8 to 4.5 V, VDDIO = 1.7 to 3.6 V, typical external component values and full load current range, unless
otherwise noted.
Pin Name
PWRON
RESETBMCU
SCL
SDA
INTB
SDWNB
Parameter
Load Condition
Min
Max
Unit
VIL
–
0.0
0.2 * VSNVS
V
VIH
–
0.8 * VSNVS
3.6
V
VOL
-2.0 mA
0.0
0.4
V
VOH
Open Drain
0.7* VIN
VIN
V
VIL
–
0.0
0.2 * VDDIO
V
VIH
–
0.8 * VDDIO
3.6
V
VIL
–
0.0
0.2 * VDDIO
V
VIH
–
0.8 * VDDIO
3.6
V
VOL
-2.0 mA
0.0
0.4
V
VOH
Open Drain
0.7*VDDIO
VDDIO
V
VOL
-2.0 mA
0.0
0.4
V
VOH
Open Drain
0.7* VIN
VIN
V
VOL
-2.0 mA
0.0
0.4
V
VOH
Open Drain
0.7* VIN
VIN
V
PF0200Z
12
Analog Integrated Circuit Device Data
Freescale Semiconductor
General Product Characteristics
Electrical Characteristics
Table 6. General PMIC Static Characteristics (continued)
TA = -40 to 85 °C, VIN = 2.8 to 4.5 V, VDDIO = 1.7 to 3.6 V, typical external component values and full load current range, unless
otherwise noted.
Pin Name
STANDBY
VDDOTP
Parameter
Load Condition
Min
Max
Unit
VIL
–
0.0
0.2 * VSNVS
V
VIH
–
0.8 * VSNVS
3.6
V
VIL
–
0.0
0.3
V
VIH
–
1.1
1.7
V
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
General Product Characteristics
Electrical Characteristics
4.3.2
Current Consumption
Table 7. Current Consumption Summary
TA = -40 to 85 °C, VIN = 3.6 V, VDDIO = 1.7 to 3.6 V, LICELL = 1.8 to 3.3 V, VSNVS = 3.0 V, typical external component values,
unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VDDIO = 3.3 V, LICELL = 3.0 V, VSNVS = 3.0 V and
25 °C, unless otherwise noted.
Mode
PF0200Z Conditions
System Conditions
Typical
MAX
Unit
(15),(16),(19)
VSNVS from LICELL
All other blocks off
VIN = 0.0 V
VSNVSVOLT[2:0] = 110
No load on VSNVS
4.0
7.0
A
Off (15)(17)
VSNVS from VIN or LICELL
Wake-up from PWRON active
32 k RC on
All other blocks off
VIN UVDET
No load on VSNVS, PMIC able to wake-up
17
25
A
Sleep (18)
VSNVS from VIN
Wake-up from PWRON active
Trimmed reference active
SW3A/B PFM
Trimmed 16 MHz RC off
32 k RC on
VREFDDR disabled
No load on VSNVS. DDR memories in self
refresh
122
220
A
Standby (18)
VSNVS from either VIN or LICELL
SW1A/B combined in PFM
SW2 in PFM
SW3A/B combined in PFM
SWBST off
Trimmed 16 MHz RC enabled
Trimmed reference active
VGEN1-6 enabled
VREFDDR enabled
No load on VSNVS. Processor enabled in
low power mode. All rails powered on
except boost (load = 0 mA)
270
430
A
Coin Cell
Notes
15.
16.
17.
18.
19.
At 25 °C only.
Refer to Figure 4 for Coin Cell mode characteristics over temperature.
When VIN is below the UVDET threshold, in the range of 1.8 V VIN < 2.65 V, the quiescent current increases by 50 A, typically.
For PFM operation, headroom should be 300 mV or greater.
Additional current may be drawn in the coin cell mode when RESETBMCU is pulled up to VSNVS due an internal path from
RESETBMCU to VIN. The additional current is UVDET
• PWRON_CFG = 1, for power button debounce timing
In addition, when the 16 MHz is active in the ON mode, the debounce times in Table 25 are referenced to the 32 kHz derived
from the 16 MHz clock. The exceptions are the LOWVINI and PWRONI interrupts, which are referenced to the 32 kHz untrimmed
clock.
Table 15. 16 MHz Clock Specifications
TA = -40 to 85 °C, VIN = 2.8 to 4.5 V, LICELL = 1.8 to 3.3 V and typical external component values. Typical values are
characterized at VIN = 3.6 V, LICELL = 3.0 V, and 25 °C, unless otherwise noted.
Parameters
Operating Voltage From VIN
16 MHz Clock Frequency
2.0 MHz Clock Frequency
(24)
Symbol
Min
Typ
Max
Units
VIN16MHz
2.8
–
4.5
V
f16MHZ
14.7
16
17.3
MHz
f2MHZ
1.84
–
2.16
MHz
Notes
24. 2.0 MHz clock is derived from the 16 MHz clock.
6.2.1
Clock adjustment
The 16 MHz clock and hence the switching frequency of the regulators, can be adjusted to improve the noise integrity of the
system. By changing the factory trim values of the 16MHz clock, the user may add an offset as small as 3.0% of the nominal
frequency.
PF0200Z
24
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Bias and References Block Description
6.3
Bias and References Block Description
6.3.1
Internal Core Voltage References
All regulators use the main bandgap as the reference. The main bandgap is bypassed with a capacitor at VCOREREF. The
bandgap and the rest of the core circuitry are supplied from VCORE. The performance of the regulators is directly dependent on
the performance of the bandgap. No external DC loading is allowed on VCORE, VCOREDIG, or VCOREREF. VCOREDIG is
kept powered as long as there is a valid supply and/or valid coin cell. Table 16 shows the main characteristics of the core circuitry.
Table 16. Core Voltages Electrical Specifications(26)
TA = -40 to 85 °C,VIN = 2.8 to 4.5 V, LICELL = 1.8 to 3.3 V, and typical external component values. Typical values are
characterized at VIN = 3.6 V, LICELL = 3.0 V, and 25 °C, unless otherwise noted.
Parameters
Symbol
Min
Typ
Max
Units
VCOREDIG
–
–
1.5
1.3
–
–
V
VCORE
–
–
2.775
0.0
–
–
V
Output Voltage(25)
VCOREREF
–
1.2
–
V
Absolute Accuracy
VCOREREFACC
–
0.5
–
%
Temperature Drift
VCOREREFTACC
–
0.25
–
%
VCOREDIG (DIGITAL CORE SUPPLY)
Output Voltage
ON mode (25)
Coin cell mode and OFF
VCORE (ANALOG CORE SUPPLY)
Output Voltage
ON mode and charging(25)
OFF and Coin cell mode
VCOREREF (BANDGAP / REGULATOR REFERENCE)
Notes
25. 3.0 V < VIN < 4.5 V, no external loading on VCOREDIG, VCORE, or VCOREREF. Extended operation down to UVDET, but no system
malfunction.
26. For information only.
6.3.1.1
External Components
Table 17. External Components for Core Voltages
Regulator
Capacitor Value (F)
VCOREDIG
1.0
VCORE
1.0
VCOREREF
0.22
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
Functional Block Requirements and Behaviors
Bias and References Block Description
6.3.2
VREFDDR Voltage Reference
VREFDDR is an internal PMOS half supply voltage follower capable of supplying up to 10 mA. The output voltage is at one half
the input voltage. Its typically used as the reference voltage for DDR memories. A filtered resistor divider is utilized to create a
low-frequency pole. This divider then utilizes a voltage follower to drive the load.
VINREFDDR
VINREFDDR
CHALF1
100 nf
VHALF
_
CHALF2
100 nf
+
Discharge
VREFDDR
VREFDDR
CREFDDR
1.0 uf
Figure 7. VREFDDR Block Diagram
6.3.2.1
VREFDDR Control Register
The VREFDDR voltage reference is controlled by a single bit in VREFDDCRTL register in Table 18.
Table 18. Register VREFDDCRTL - ADDR 0x6A
Name
UNUSED
VREFDDREN
UNUSED
Bit #
R/W
Default
Description
3:0
–
0x00
UNUSED
4
R/W
0x00
Enable or disables VREFDDR output voltage
0 = VREFDDR Disabled
1 = VREFDDR Enabled
7:5
–
0x00
UNUSED
External Components
Table 19. VREFDDR External Components(27)
Capacitor
Capacitance (F)
VINREFDDR(28) to VHALF
0.1
VHALF to GND
0.1
VREFDDR
1.0
Notes
27. Use X5R or X7R capacitors.
28. VINREFDDR to GND, 1.0 F minimum capacitance is provided by buck regulator output.
PF0200Z
26
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Bias and References Block Description
VREFDDR Specifications
Table 20. VREFDDR Electrical Characteristics
TA = -40 to 85 °C, VIN = 3.6 V, IREFDDR = 0.0 mA, VINREFDDR = 1.5 V and typical external component values, unless otherwise
noted. Typical values are characterized at VIN = 3.6 V, IREFDDR = 0.0 mA, VINREFDDR = 1.5 V, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
Operating Input Voltage Range
VINREFDDR
1.2
–
1.8
V
Operating Load Current Range
IREFDDR
0.0
–
10
mA
IREFDDRLIM
10.5
15
25
mA
IREFDDRQ
–
8.0
–
A
Output Voltage
1.2 V < VINREFDDR < 1.8 V
0.0 mA < IREFDDR < 10 mA
VREFDDR
–
VINREFDDR/2
–
V
Output Voltage Tolerance
1.2 V < VINREFDDR < 1.8 V
0.6 mA IREFDDR 10 mA
VREFDDRTOL
–1.0
–
1.0
%
Load Regulation
1.0 mA < IREFDDR < 10 mA
1.2 V < VINREFDDR < 1.8 V
VREFDDRLOR
–
0.40
–
mV/mA
Turn-on Time
Enable to 90% of end value
VINREFDDR = 1.2 V, 1.8 V
IREFDDR = 0.0 mA
tONREFDDR
–
–
100
s
Turn-off Time
Disable to 10% of initial value
VINREFDDR = 1.2 V, 1.8 V
IREFDDR = 0.0 mA
tOFFREFDDR
–
–
10
ms
Start-up Overshoot
VINREFDDR = 1.2 V, 1.8 V
IREFDDR = 0.0 mA
VREFDDROSH
–
1.0
6.0
%
Transient Load Response
VINREFDDR = 1.2 V, 1.8 V
VREFDDRTLR
–
5.0
–
mV
VREFDDR
Current Limit
IREFDDR when VREFDDR is forced to VINREFDDR/4
Quiescent Current(29)
ACTIVE MODE – DC
ACTIVE MODE – AC
Notes
29. When VREFDDR is off there is a quiescent current of 1.5 A typical.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
Functional Block Requirements and Behaviors
Power Generation
6.4
Power Generation
6.4.1
Modes of Operation
The operation of the PF0200Z can be reduced to five states, or modes: ON, OFF, Sleep, Standby, and Coin Cell. Figure 8 shows
the state diagram of the PF0200Z, along with the conditions to enter and exit from each state.
Coin Cell
VIN < UVDET
VIN < UVDET
VIN > UVDET
PWRON = 0 held >= 4.0 sec
Any SWxOMODE bits=1
& PWRONRSTEN = 1
(PWRON_CFG=1)
VIN < UVDET
PWRON = 0
Any SWxOMODE bits=1
(PWRON_CFG=0)
Or
PWRON=0 held >= 4.0 sec
Any SWxOMODE bits=1
& PWRONRSTEN = 1
(PWRON_CFG=1)
Thermal shutdown
OFF
PWRON=1
& VIN > UVDET
VIN < UVDET
(PWRON_CFG = 0)
Sleep
Or
PWRON = 0
PWRON= 0 < 4.0 sec
Any SWxOMODE bits=1
& VIN > UVDET
(PWRON_CFG=0)
(PWRON_CFG=1)
Or
PWRON = 0
PWRON=0 held >= 4.0 sec
All SWxOMODE bits= 0
Any SWxOMODE bits=1
(PWRON_CFG = 0)
& PWRONRSTEN = 1
Or
(PWRON_CFG=1)
PWRON = 0 held >= 4.0 sec
PWRON=1
All SWxOMODE bits= 0
& VIN > UVDET
& PWRONRSTEN = 1
(PWRON_CFG =0)
(PWRON_CFG = 1)
Or
ON
PWRON= 0 < 4.0 sec
& VIN > UVDET
Thermal shudown
(PWRON_CFG=1)
STANDBY asserted
STANDBY de-asserted
Standby
PWRON = 0
All SWxOMODE bits= 0
(PWRON_CFG = 0)
Or
PWRON = 0 held >= 4.0 sec
All SWxOMODE bits= 0
& PWRONRSTEN = 1
(PWRON_CFG = 1)
Thermal shutdown
Figure 8. State Diagram
To complement the state diagram in Figure 8, a description of the states is provided in following sections. Note that VIN must
exceed the rising UVDET threshold to allow a power up. Refer to Table 27 for the UVDET thresholds. Additionally, I2C control is
not possible in the Coin Cell mode and the interrupt signal, INTB, is only active in Sleep, Standby, and ON states.
6.4.1.1
ON Mode
The PF0200Z enters the On mode after a turn-on event. RESETBMCU is de-asserted, high, in this mode of operation.
PF0200Z
28
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
6.4.1.2
OFF Mode
The PF0200Z enters the Off mode after a turn-off event. A thermal shutdown event also forces the PF0200Z into the Off mode.
Only VCOREDIG and VSNVS are powered in the mode of operation. To exit the Off mode, a valid turn-on event is required.
RESETBMCU is asserted, LOW, in this mode.
6.4.1.3
Standby Mode
• Depending on STANDBY pin configuration, Standby is entered when the STANDBY pin is asserted. This is typically used
for low-power mode of operation.
• When STANDBY is de-asserted, Standby mode is exited.
A product may be designed to go into a Low-power mode after periods of inactivity. The STANDBY pin is provided for board level
control of going in and out of such deep sleep modes (DSM).
When a product is in DSM, it may be able to reduce the overall platform current by lowering the regulator output voltage, changing
the operating mode of the regulators or disabling some regulators. The configuration of the regulators in Standby is preprogrammed through the I2C interface.
Note that the STANDBY pin is programmable for Active High or Active Low polarity, and that decoding of a Standby event will
take into account the programmed input polarity as shown in Table 21. When the PF0200Z is powered up first, regulator settings
for the Standby mode are mirrored from the regulator settings for the ON mode. To change the STANDBY pin polarity to Active
Low, set the STANDBYINV bit via software first, and then change the regulator settings for Standby mode as required. For
simplicity, STANDBY will generally be referred to as active high throughout this document.
Table 21. Standby Pin and Polarity Control
STANDBY (Pin)(31)
STANDBYINV (I2C bit)(32)
STANDBY Control (30)
0
0
0
0
1
1
1
0
1
1
1
0
Notes
30. STANDBY = 0: System is not in Standby, STANDBY = 1: System is in Standby
31. The state of the STANDBY pin only has influence in On mode.
32. Bit 6 in Power Control Register (ADDR - 0x1B)
Since STANDBY pin activity is driven asynchronously to the system, a finite time is required for the internal logic to qualify and
respond to the pin level changes. A programmable delay is provided to hold off the system response to a Standby event. This
allows the processor and peripherals some time after a standby instruction has been received to terminate processes to facilitate
seamless entering into Standby mode.
When enabled (STBYDLY = 01, 10, or 11) per Table 22, STBYDLY will delay the Standby initiated response for the entire IC,
until the STBYDLY counter expires.
An allowance should be made for three additional 32 k cycles required to synchronize the Standby event.
Table 22. STANDBY Delay - Initiated Response
STBYDLY[1:0](33)
Function
00
No Delay
01
One 32 k period (default)
10
Two 32 k periods
11
Three 32 k periods
Notes
33. Bits [5:4] in Power Control Register (ADDR - 0x1B)
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
Functional Block Requirements and Behaviors
Power Generation
6.4.1.4
Sleep Mode
• Depending on PWRON pin configuration, Sleep mode is entered when PWRON is de-asserted and SWxOMODE bit is set.
• To exit Sleep mode, assert the PWRON pin.
In the Sleep mode, the regulator will use the set point as programmed by SW1ABOFF[5:0] for SW1A/B and by SWxOFF[6:0] for
SW2 and SW3A/B. The activated regulators will maintain settings for this mode and voltage until the next turn-on event. Table 23
shows the control bits in Sleep mode. During Sleep mode, interrupts are active and the INTB pin will report any unmasked fault
event.
Table 23. Regulator Mode Control
SWxOMODE
Off Operational Mode (Sleep) (34)
0
Off
1
PFM
Notes
34. For sleep mode, an activated switching regulator, should use the off
mode set point as programmed by SW1ABOFF[5:0] for SW1A/B and
SWxOFF[6:0] for SW2 and SW3A/B.
6.4.1.5
Coin Cell Mode
In the Coin Cell state, the coin cell is the only valid power source (VIN = 0.0 V) to the PMIC. No turn-on event is accepted in the
Coin Cell state. Transition to the OFF state requires that VIN surpasses UVDET threshold. RESETBMCU is held low in this mode.
If the coin cell is depleted, a complete system reset will occur. At the next application of power and the detection of a Turn-on
event, the system will be re-initialized with all I2C bits including those that reset on COINPORB, are restored to their default
states.
PF0200Z
30
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
6.4.2
State Machine Flow Summary
Table 24 provides a summary matrix of the PF0200Z flow diagram to show the conditions needed to transition from one state to
another.
Table 24. State Machine Flow Summary
Next State
STATE
OFF
Coin cell
Sleep
Standby
ON
OFF
X
VIN < UVDET
X
X
PWRON_CFG = 0
PWRON = 1 & VIN > UVDET
or
PWRON_CFG = 1
PWRON = 0 < 4.0 s
& VIN > UNDET
Coin cell
VIN > UVDET
X
X
X
X
Thermal Shutdown
Initial State
Sleep
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
Any SWxOMODE = 1 &
PWRONRSTEN = 1
VIN < UVDET
X
X
PWRON_CFG = 0
PWRON = 1 & VIN > UVDET
or
PWRON_CFG = 1
PWRON = 0 < 4.0 s &
VIN > UNDET
VIN < UVDET
PWRON_CFG = 0
PWRON = 0
Any SWxOMODE = 1
or
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
Any SWxOMODE = 1 &
PWRONRSTEN = 1
X
Standby de-asserted
VIN < UVDET
PWRON_CFG = 0
PWRON = 0
Any SWxOMODE = 1
or
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
Any SWxOMODE = 1 &
PWRONRSTEN = 1
Standby
asserted
X
Thermal Shutdown
Standby
PWRON_CFG = 0
PWRON = 0
All SWxOMODE = 0
or
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
All SWxOMODE = 0 &
PWRONRSTEN = 1
Thermal Shutdown
ON
6.4.2.1
PWRON_CFG = 0
PWRON = 0
All SWxOMODE = 0
or
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
All SWxOMODE = 0 &
PWRONRSTEN = 1
Turn On Events
From OFF and Sleep modes, the PMIC is powered on by a turn-on event. The type of Turn-on event depends on the configuration
of PWRON. PWRON may be configured as an active high when PWRON_CFG = 0, or as the input of a mechanical switch when
PWRON_CFG = 1. VIN must be greater than UVDET for the PMIC to turn-on. When PWRON is configured as an active high and
PWRON is high (pulled up to VSNVS) before VIN is valid, a VIN transition from 0.0 V to a voltage greater than UVDET is also a
Turn-on event. See the State diagram, Figure 8, and the Table 24 for more details. Any regulator enabled in the Sleep mode will
remain enabled when transitioning from Sleep to ON, i.e., the regulator will not be turned off and then on again to match the startup sequence. The following is a more detailed description of the PWRON configurations:
• If PWRON_CFG = 0, the PWRON signal is high and VIN > UVDET, the PMIC will turn on; the interrupt and sense bits,
PWRONI and PWRONS respectively, will be set.
• If PWRON_CFG = 1, VIN > UVDET and PWRON transitions from high to low, the PMIC will turn on; the interrupt and sense
bits, PWRONI and PWRONS respectively, will be set.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
Functional Block Requirements and Behaviors
Power Generation
The sense bit will show the real time status of the PWRON pin. In this configuration, the PWRON input can be a mechanical
switch debounced through a programmable debouncer, PWRONDBNC[1:0], to avoid a response to a very short (i.e.,
unintentional) key press. The interrupt is generated for both the falling and the rising edge of the PWRON pin. By default, a 30 ms
interrupt debounce is applied to both falling and rising edges. The falling edge debounce timing can be extended with
PWRONDBNC[1:0] as defined in the table below. The interrupt is cleared by software, or when cycling through the OFF mode.
Table 25. PWRON Hardware Debounce Bit Settings
Bits
PWRONDBNC[1:0]
State
Turn On
Debounce (ms)
Falling Edge INT
Debounce (ms)
Rising Edge INT
Debounce (ms)
00
0.0
31.25
31.25
01
31.25
31.25
31.25
10
125
125
31.25
11
750
750
31.25
Notes
35. The sense bit, PWRONS, is not debounced and follows the state of the PWRON pin.
6.4.2.2
Turn Off Events
PWRON Pin
The PWRON pin is used to power off the PF0200Z. The PWRON pin can be configured with OTP to power off the PMIC under
the following two conditions:
1. PWRON_CFG bit = 0, SWxOMODE bit = 0 and PWRON pin is low.
2. PWRON_CFG bit = 1, SWxOMODE bit = 0, PWRONRSTEN = 1 and PWRON is held low for longer than 4.0
seconds. Alternatively, the system can be configured to restart automatically by setting the RESTARTEN bit.
Thermal Protection
If the die temperature surpasses a given threshold, the thermal protection circuit will power off the PMIC to avoid damage. A turnon event will not power on the PMIC while it is in thermal protection. The part will remain in Off mode until the die temperature
decreases below a given threshold. There are no specific interrupts related to this other than the warning interrupt. See Power
Dissipation section for more detailed information.
Undervoltage Detection
When the voltage at VIN drops below the undervoltage falling threshold, UVDET, the state machine will transition to the Coin Cell
mode.
6.4.3
Power Tree
The PF0200Z PMIC features four buck regulators, one boost regulator, six general purpose LDOs, one switch/LDO combination,
and a DDR voltage reference to supply voltages for the application processor and peripheral devices. The buck regulators as
well as the boost regulator are supplied directly from the main input supply (VIN). The inputs to all of the buck regulators must be
tied to VIN, whether they are powered on or off. The six general use LDO regulators are directly supplied from the main input
supply or from the switching regulators depending on the application requirements. Since VREFDDR is intended to provide DDR
memory reference voltage, it should be supplied by any rail supplying voltage to DDR memories; the typical application
recommends the use of SW3 as the input supply for VREFDDR. VSNVS is supplied by either the main input supply or the coin
cell. Refer to Table 26 for a summary of all power supplies provided by the PF0200Z.
PF0200Z
32
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 26. Power Tree Summary
Supply
Output Voltage (V)
Step Size (mV)
Maximum Load Current (mA)
SW1A/B
0.3 - 1.875
25
2500
SW2
0.4 - 3.3
25/50
1500
SW3A/B
0.4 - 3.3
25/50
1250(36)
SWBST
5.00/5.05/5.10/5.15
50
600
VGEN1
0.80 – 1.55
50
100
VGEN2
0.80 – 1.55
50
250
VGEN3
1.8 – 3.3
100
100
VGEN4
1.8 – 3.3
100
350
VGEN5
1.8 – 3.3
100
100
VGEN6
1.8 – 3.3
100
200
VSNVS
1.0 - 3.0
NA
0.4
VREFDDR
0.5*SW3A_OUT
NA
10
Notes
36. Current rating per independent phase, when SW3A/B is set in single phase, current capability is up to
2500 mA.
Figure 9 shows a simplified power map with various recommended options to supply the different block within the PF0200Z, as
well as the typical application voltage domain on the i.MX 6 application processors. Note that each application power tree is
dependent upon the system’s voltage and current requirements, therefore a proper input voltage should be selected for the
regulators.
The minimum operating voltage for the main VIN supply is 2.8 V, for lower voltages proper operation is not guaranteed. However
at initial power up, the input voltage must surpass the rising UVDET threshold before proper operation is guaranteed. Refer to
the tables and text specifying each supply for information on performance metrics and operating ranges. Table 27 summarizes
the UVDET thresholds.
Table 27. UVDET Threshold
UVDET Threshold
VIN
Rising
3.1 V
Falling
2.65 V
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
33
Functional Block Requirements and Behaviors
Power Generation
SW1A
CORE
(0.3 to 1.875 V), 1.25 A
i.MX6X
MCU
VDDARM_IN
VDDSOC_IN
SW1B
CORE
(0.3 to 1.875 V), 1.25 A
SW2
VDDHIGH
(0.4 to 3.3 V), 1.5 A
VIN
2.8 - 4.5 V
VDDHIGH_IN
SW3A
DDR CORE
(0.4 to 3.3 V), 1.25 A
SW3B
DDR IO
(0.4 to 3.3 V), 1.25 A
SWBST
5.0 V, 0.6 A
VIN
MUX /
COIN
CHRG
Coincell
VINMAX = 3.4 V
VGEN2
(0.80 to 1.55 V),
250 mA
VGEN3
(1.8 to 3.3 V),
100 mA
VIN
VINMAX = 3.6 V
VSNVS_IN
USB_OTG
DDR3
Peripherals
VGEN4
(1.8 to 3.3 V),
350 mA
VGEN5
(1.8 to 3.3 V),
100 mA
VIN
SW2
VSNVS
1.0 to 3.0 V,
400 uA
VGEN1
(0.80 to 1.55 V),
100 mA
VIN
SW2
LDO_3p0
VREFDDR
0.5*VDDR, 10 mA
SW3A/B
SW2
VDD_DDR_IO
VINMAX = 4.5 V
VGEN6
(1.8 to 3.3 V),
200 mA
Figure 9. PF0200Z Typical Power Map
PF0200Z
34
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
6.4.4
Buck Regulators
Each buck regulator is capable of operating in PFM, APS, and PWM switching modes.
6.4.4.1
Current Limit
Each buck regulator has a programmable current limit. In an overcurrent condition, the current is limited cycle-by-cycle. If the
current limit condition persists for more than 8.0 ms, a fault interrupt is generated.
6.4.4.2
General Control
To improve system efficiency the buck regulators can operate in different switching modes. Changing between switching modes
can occur by any of the following means: I2C programming, exiting/entering the Standby mode, exiting/entering Sleep mode, and
load current variation. Available switching modes for buck regulators are presented in Table 28.
Table 28. Switching Mode Description
Mode
Description
OFF
The regulator is switched off and the output voltage is discharged.
PFM
In this mode, the regulator is always in PFM mode, which is useful at light loads for
optimized efficiency.
PWM
In this mode, the regulator is always in PWM mode operation regardless of load conditions.
APS
In this mode, the regulator moves automatically between pulse skipping mode and PWM
mode depending on load conditions.
During soft-start of the buck regulators, the controller transitions through the PFM, APS, and PWM switching modes. 3.0 ms
(typical) after the output voltage reaches regulation, the controller transitions to the selected switching mode. Depending on the
particular switching mode selected, additional ripple may be observed on the output voltage rail as the controller transitions
between switching modes.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
35
Functional Block Requirements and Behaviors
Power Generation
Table 29 summarizes the Buck regulator programmability for Normal and Standby modes.
Table 29. Regulator Mode Control
SWxMODE[3:0]
Normal Mode
Standby Mode
0000
Off
Off
0001
PWM
Off
0010
Reserved
Reserved
0011
PFM
Off
0100
APS
Off
0101
PWM
PWM
0110
PWM
APS
0111
Reserved
Reserved
1000
APS
APS
1001
Reserved
Reserved
1010
Reserved
Reserved
1011
Reserved
Reserved
1100
APS
PFM
1101
PWM
PFM
1110
Reserved
Reserved
1111
Reserved
Reserved
Transitioning between Normal and Standby modes can affect a change in switching modes as well as output voltage. The rate
of the output voltage change is controlled by the Dynamic Voltage Scaling (DVS), explained in Dynamic Voltage Scaling. The
output voltage options are the same for Normal and Standby modes for each regulator.
When in Standby mode, the regulator outputs the voltage programmed in its standby voltage register and will operate in the mode
selected by the SWxMODE[3:0] bits. Upon exiting Standby mode, the regulator will return to its normal switching mode and its
output voltage programmed in its voltage register.
Any regulators whose SWxOMODE bit is set to “1” will enter Sleep mode if a PWRON turn-off event occurs, and any regulator
whose SWxOMODE bit is set to “0” will be turned off. In Sleep mode, the regulator outputs the voltage programmed in its off
(Sleep) voltage register and operates in the PFM mode. The regulator will exit the Sleep mode when a turn-on event occurs. Any
regulator whose SWxOMODE bit is set to “1” will remain on and change to its normal configuration settings when exiting the Sleep
state to the ON state. Any regulator whose SWxOMODE bit is set to “0” will be powered up with the same delay in the start-up
sequence as when powering On from Off. At this point, the regulator returns to its default ON state output voltage and switch
mode settings.
Table 23 shows the control bits in Sleep mode. When Sleep mode is activated by the SWxOMODE bit, the regulator will use the
set point as programmed by SW1ABOFF[5:0] for SW1A/B and by SWxOFF[6:0] for SW2 and SW3A/B.
Dynamic Voltage Scaling
To reduce overall power consumption, processor core voltages can be varied depending on the mode or activity level of the
processor.
1. Normal operation: The output voltage is selected by I2C bits SW1AB[5:0] for SW1A/B and SWx[6:0] for SW2 and SW3A/B.
A voltage transition initiated by I2C is governed by the DVS stepping rates shown in Table 32 and Table 33.
2. Standby Mode: The output voltage can be higher, or lower than in normal operation, but is typically selected to be the
lowest state retention voltage of a given processor; it is selected by I2C bits SW1ABSTBY[5:0] for SW1A/B and by bits
SWxSTBY[6:0] for SW2 and SW3A/B. Voltage transitions initiated by a Standby event are governed by the
SW1ABDVSSPEED[1:0] and SWxDVSSPEED[1:0] I2C bits shown in Table 32 and Table 33, respectively.
PF0200Z
36
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
3. Sleep Mode: The output voltage can be higher or lower than in normal operation, but is typically selected to be the lowest
state retention voltage of a given processor; it is selected by I2C bits SW1ABOFF[5:0] for SW1A/B and by bits
SWxOFF[6:0] for SW2, and SW3A/B. Voltage transitions initiated by a turn-off event are governed by the
SW1ABDVSSPEED[1:0] and SWxDVSSPEED[1:0] I2C bits shown in Table 32 and Table 33, respectively.
Table 30, Table 31, Table 32, and Table 33 summarize the set point control and DVS time stepping applied to all regulators.
Table 30. DVS Control Logic for SW1A/B
STANDBY
Set Point Selected by
0
SW1AB[5:0]
1
SW1ABSTBY[5:0]
Table 31. DVS Control Logic for SW2 and SW3A/B
STANDBY
Set Point Selected by
0
SWx[6:0]
1
SWxSTBY[6:0]
Table 32. DVS Speed Selection for SW1A/B
SW1ABDVSSPEED[1:0]
Function
00
25 mV step each 2.0 s
01 (default)
25 mV step each 4.0 s
10
25 mV step each 8.0 s
11
25 mV step each 16 s
Table 33. DVS Speed Selection for SW2 and SW3A/B
SWxDVSSPEED[1:0]
Function
SWx[6] = 0 or SWxSTBY[6] = 0
Function
SWx[6] = 1 or SWxSTBY[6] = 1
00
25 mV step each 2.0 s
50 mV step each 4.0 s
01 (default)
25 mV step each 4.0 s
50 mV step each 8.0 s
10
25 mV step each 8.0 s
50 mV step each 16 s
11
25 mV step each 16 s
50 mV step each 32 s
The regulators have a strong sourcing capability and sinking capability in PWM mode, therefore the fastest rising and falling
slopes are determined by the regulator in PWM mode. However, if the regulators are programmed in PFM or APS mode during
a DVS transition, the falling slope can be influenced by the load. Additionally, as the current capability in PFM mode is reduced,
controlled DVS transitions in PFM mode could be affected. Critically timed DVS transitions are best assured with PWM mode
operation.
The following diagram shows the general behavior for the regulators when initiated with I2C programming, or standby control.
During the DVS period the overcurrent condition on the regulator should be masked.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
37
Functional Block Requirements and Behaviors
Power Generation
Requested
Set Point
Output Voltage
with light Load
Internally
Controlled Steps
Example
Actual Output
Voltage
Output
Voltage
Initial
Set Point
Actual
Output Voltage
Internally
Possible
Output Voltage
Window
Controlled Steps
Voltage
Change
Request
Request for
Higher Voltage
Request for
Lower Voltage
Initiated by I2C Programming, Standby Control
Figure 10. Voltage Stepping with DVS
Regulator Phase Clock
The SWxPHASE[1:0] bits select the phase of the regulator clock as shown in Table 34. By default, each regulator is initialized at
90 ° out of phase with respect to each other. For example, SW1A/B is set to 0 °, SW2 is set to 90 ° and SW3A/B is set to 180 °
by default at power up.
Table 34. Regulator Phase Clock Selection
SWxPHASE[1:0]
Phase of Clock Sent to Regulator
(degrees)
00
0
01
90
10
180
11
270
The SWxFREQ[1:0] register is used to set the desired switching frequency for each one of the buck regulators. Table 36 shows
the selectable options for SWxFREQ[1:0]. For each frequency, all phases will be available, this allows regulators operating at
different frequencies to have different relative switching phases. However, not all combinations are practical. For example,
2.0 MHz, 90 ° and 4.0 MHz, 180 ° are the same in terms of phasing. Table 35 shows the optimum phasing when using more than
one switching frequency.
Table 35. Optimum Phasing
Frequencies
Optimum Phasing
1.0 MHz
2.0 MHz
0°
180 °
1.0 MHz
4.0 MHz
0°
180 °
2.0 MHz
4.0 MHz
0°
180 °
1.0 MHz
2.0 MHz
4.0 MHz
0°
90 °
90 °
PF0200Z
38
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 36. Regulator Frequency Configuration
SWxFREQ[1:0]
Frequency
00
1.0 MHz
01
2.0 MHz
10
4.0 MHz
11
Reserved
Programmable Maximum Current
The maximum current, ISWxMAX, of each buck regulator is programmable. This allows the use of smaller inductors where lower
currents are required. Programmability is accomplished by choosing the number of paralleled power stages in each regulator.
The SWx_PWRSTG[2:0] bits on the Extended Page 2 of the register map control the number of power stages. See Table 37 for
the programmable options. Bit[0] must always be enabled to ensure the stage with the current sensor is chosen. The default
setting, SWx_PWRSTG[2:0] = 111, represents the highest maximum current. The current limit for each option is also scaled by
the percentage of power stages that are enabled.
Table 37. Programmable Current Configuration
Regulators
% of Power Stages
Enabled
Control Bits
SW1AB_PWRSTG[2:0]
SW1AB
ISW1ABMAX
0
0
1
40%
1.0
0
1
1
80%
2.0
1
0
1
60%
1.5
1
1
1
100%
2.5
SW2_PWRSTG[2:0]
SW2
ISW2MAX
0
0
1
38%
0.55
0
1
1
75%
1.125
1
0
1
63%
0.95
1
1
1
100%
1.5
SW3A_PWRSTG[2:0]
SW3A
ISW3AMAX
0
0
1
40%
0.5
0
1
1
80%
1.0
1
0
1
60%
0.75
1
1
1
100%
1.25
SW3B_PWRSTG[2:0]
SW3B
Rated Current (A)
ISW3BMAX
0
0
1
40%
0.5
0
1
1
80%
1.0
1
0
1
60%
0.75
1
1
1
100%
1.25
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
39
Functional Block Requirements and Behaviors
Power Generation
6.4.4.3
SW1A/B
SW1A/B is a 2.5 A single phase regulator. The SW1ALX and SW1BLX pins should be connected together on the board.
SW1_CONFIG[1:0] = 01 is the only configuration supported.
The single phase configuration is programmed by OTP by using SW1_CONFIG[1:0] bits in the register map Extended Page 1,
as shown in Table 38.
.
Table 38. SW1 Configuration
SW1_CONFIG[1:0]
Description
00
Reserved
01
A/B Single Phase
10
Reserved
11
Reserved
SW1A/B Single Phase
In this configuration, SW1A/B is connected as a single phase with a single inductor. This configuration allows reduced component
count by using only one inductor for SW1A/B. Figure 11 shows the physical connection for SW1A/B in single phase.
VIN
SW1AIN
SW1AMODE
ISENSE
CINSW1A
SW1A/B
SW1ALX
LSW1A
COSW1A
Controller
Driver
SW1AFAULT
Internal
Compensation
SW1FB
I2C
Z2
Z1
EA
VREF
DAC
I2C
Interface
VIN
SW1BIN
SW1BMODE
ISENSE
CINSW1B
SW1BLX
Controller
Driver
SW1BFAULT
EP
Figure 11. SW1A/B Single Phase Block Diagram
Both SW1ALX and SW1BLX nodes operate at the same DVS, frequency, and phase configured by the SW1ABCONF register.
PF0200Z
40
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
SW1A/B Setup and Control Registers
SW1A/B output voltage is programmable from 0.300 to 1.875 V in steps of 25 mV. The output voltage set point is independently
programmed for Normal, Standby, and Sleep mode by setting the SW1AB[5:0], SW1ABSTBY[5:0], and SW1ABOFF[5:0] bits
respectively. Table 39 shows the output voltage coding for SW1A/B. Note: Output voltages of 0.6 V and below are not supported.
Table 39. SW1A/B Output Voltage Configuration
Set Point
SW1AB[5:0]
SW1ABSTBY[5:0]
SW1ABOFF[5:0]
SW1AB Output (V)
Set Point
SW1AB[5:0]
SW1ABSTBY[5:0]
SW1ABOFF[5:0]
SW1AB Output (V)
0
000000
0.3000
32
100000
1.1000
1
000001
0.3250
33
100001
1.1250
2
000010
0.3500
34
100010
1.1500
3
000011
0.3750
35
100011
1.1750
4
000100
0.4000
36
100100
1.2000
5
000101
0.4250
37
100101
1.2250
6
000110
0.4500
38
100110
1.2500
7
000111
0.4750
39
100111
1.2750
8
001000
0.5000
40
101000
1.3000
9
001001
0.5250
41
101001
1.3250
10
001010
0.5500
42
101010
1.3500
11
001011
0.5750
43
101011
1.3750
12
001100
0.6000
44
101100
1.4000
13
001101
0.6250
45
101101
1.4250
14
001110
0.6500
46
101110
1.4500
15
001111
0.6750
47
101111
1.4750
16
010000
0.7000
48
110000
1.5000
17
010001
0.7250
49
110001
1.5250
18
010010
0.7500
50
110010
1.5500
19
010011
0.7750
51
110011
1.5750
20
010100
0.8000
52
110100
1.6000
21
010101
0.8250
53
110101
1.6250
22
010110
0.8500
54
110110
1.6500
23
010111
0.8750
55
110111
1.6750
24
011000
0.9000
56
111000
1.7000
25
011001
0.9250
57
111001
1.7250
26
011010
0.9500
58
111010
1.7500
27
011011
0.9750
59
111011
1.7750
28
011100
1.0000
60
111100
1.8000
29
011101
1.0250
61
111101
1.8250
30
011110
1.0500
62
111110
1.8500
31
011111
1.0750
63
111111
1.8750
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
41
Functional Block Requirements and Behaviors
Power Generation
Table 40 provides a list of registers used to configure and operate SW1A/B and a detailed description on each one of these
register is provided in Table 41 through Table 45.
Table 40. SW1A/B Register Summary
Register
Address
Output
SW1ABVOLT
0x20
SW1AB Output voltage set point in normal operation
SW1ABSTBY
0x21
SW1AB Output voltage set point on Standby
SW1ABOFF
0x22
SW1AB Output voltage set point on Sleep
SW1ABMODE
0x23
SW1AB Switching Mode selector register
SW1ABCONF
0x24
SW1AB DVS, Phase, Frequency and ILIM configuration
Table 41. Register SW1ABVOLT - ADDR 0x20
Name
Bit #
R/W
Default
Description
SW1AB
5:0
R/W
0x00
Sets the SW1AB output voltage during normal
operation mode. See Table 39 for all possible
configurations.
UNUSED
7:6
–
0x00
UNUSED
Table 42. Register SW1ABSTBY - ADDR 0x21
Name
Bit #
R/W
Default
Description
SW1ABSTBY
5:0
R/W
0x00
Sets the SW1AB output voltage during Standby
mode. See Table 39 for all possible
configurations.
UNUSED
7:6
–
0x00
UNUSED
Table 43. Register SW1ABOFF - ADDR 0x22
Name
Bit #
R/W
Default
Description
SW1ABOFF
5:0
R/W
0x00
Sets the SW1AB output voltage during Sleep
mode. See Table 39 for all possible
configurations.
UNUSED
7:6
–
0x00
UNUSED
Table 44. Register SW1ABMODE - ADDR 0x23
Name
Bit #
R/W
Default
3:0
R/W
0x80
Sets the SW1AB switching operation mode.
See Table 29 for all possible configurations.
UNUSED
4
–
0x00
UNUSED
SW1ABOMODE
5
R/W
0x00
Set status of SW1AB when in Sleep mode
0 = OFF
1 = PFM
7:6
–
0x00
UNUSED
SW1ABMODE
UNUSED
Description
PF0200Z
42
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 45. Register SW1ABCONF - ADDR 0x24
Name
Bit #
R/W
Default
Description
SW1ABILIM
0
R/W
0x00
SW1AB current limit level selection
0 = High level current limit
1 = Low level current limit
UNUSED
1
R/W
0x00
Unused
SW1ABFREQ
3:2
R/W
0x00
SW1A/B switching frequency selector
See Table 36.
SW1ABPHASE
5:4
R/W
0x00
SW1A/B Phase clock selection
See Table 34.
SW1ABDVSSPEED
7:6
R/W
0x00
SW1A/B DVS speed selection
See Table 32.
SW1A/B External Components
Table 46. SW1A/B External Component Recommendations
Mode
Components
SW1A Input capacitor
4.7 F
SW1A Decoupling input capacitor
0.1 F
(37)
SW1B Input capacitor
4.7 F
(37)
SW1B Decoupling input capacitor
0.1 F
CINSW1B
CIN1BHF
A/B Single Phase
(37)
CINSW1A
CIN1AHF
Description
(37)
COSW1AB
(37)
LSW1A
SW1A/B Output capacitor
SW1A/B Inductor
4 x 22 F
1.0 H
DCR = 12 m
ISAT = 4.5 A
Notes
37. Use X5R or X7R capacitors.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
43
Functional Block Requirements and Behaviors
Power Generation
SW1A/B Specifications
Table 47. SW1A/B Electrical Characteristics
All parameters are specified at TA = -40 to 85 °C, VIN = VINSW1x = 3.6 V, VSW1AB = 1.2 V, ISW1AB = 100 mA,
SW1AB_PWRSTG[2:0] = [111], typical external component values, fSW1AB = 2.0 MHz, unless otherwise noted. Typical values
are characterized at VIN = VINSW1x = 3.6 V, VSW1AV = 1.2 V, ISW1AB = 100 mA, SW1AB_PWRSTG[2:0] = [111], and 25 °C,
unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
Operating Input Voltage
VINSW1A
VINSW1B
2.8
–
4.5
V
Nominal Output Voltage
VSW1AB
–
Table 39
–
V
-25
-3.0%
-
25
3.0%
-65
-45
-3.0%
–
–
–
65
45
3.0%
–
–
2500
4.5
3.3
6.5
4.9
8.5
6.4
SW1A/B (SINGLE PHASE)
Output Voltage Accuracy
• PWM, APS, 2.8 V < VIN < 4.5 V, 0 < ISW1AB < 2.5 A
0.625 V VSW1AB 1.450 V
1.475 V VSW1AB 1.875 V
•
PFM, steady state, 2.8 V < VIN < 4.5 V, 0 < ISW1AB < 150 mA
0.625 V < VSW1AB < 0.675 V
0.7 V < VSW1AB < 0.85 V
0.875 V < VSW1AB < 1.875 V
VSW1ABACC
Rated Output Load Current, (38)
2.8 V < VIN < 4.5 V, 0.625 V < VSW1AB < 1.875 V
ISW1AB
Current Limiter Peak Current Detection (38)
• SW1A/B Single Phase (current through inductor)
SW1ABILIM = 0
SW1ABILIM = 1
ISW1ABLIM
mV
%
mA
A
Start-up Overshoot
ISW1AB = 0.0 mA
DVS clk = 25 mV/4 s, VIN = VINSW1x = 4.5 V, VSW1AB = 1.875 V
VSW1ABOSH
–
–
66
mV
Turn-on Time
Enable to 90% of end value
ISW1AB = 0.0 mA
DVS clk = 25 mV/4 s, VIN = VINSW1x = 4.5 V, VSW1AB = 1.875 V
tONSW1AB
–
–
500
µs
–
–
–
1.0
2.0
4.0
–
–
–
–
–
–
–
–
–
82
84
86
87
82
71
–
–
–
–
–
–
VSW1AB
–
10
–
mV
Line Regulation (APS, PWM)
VSW1ABLIR
–
–
20
mV
DC Load Regulation (APS, PWM)
VSW1ABLOR
–
–
20
mV
Switching Frequency
SW1ABFREQ[1:0] = 00
SW1ABFREQ[1:0] = 01
SW1ABFREQ[1:0] = 10
Efficiency (Single Phase)
• VIN = 3.6 V, fSW1AB = 2.0 MHz, LSW1AB = 1.0 H
PFM, 0.9 V, 1.0 mA
PFM, 1.2 V, 50 mA
APS, PWM, 1.2 V, 500 mA
APS, PWM, 1.2 V, 750 mA
APS, PWM, 1.2 V, 1250 mA
APS, PWM, 1.2 V, 2500 mA
Output Ripple
fSW1AB
SW1AB
MHz
%
PF0200Z
44
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 47. SW1A/B Electrical Characteristics (continued)
All parameters are specified at TA = -40 to 85 °C, VIN = VINSW1x = 3.6 V, VSW1AB = 1.2 V, ISW1AB = 100 mA,
SW1AB_PWRSTG[2:0] = [111], typical external component values, fSW1AB = 2.0 MHz, unless otherwise noted. Typical values
are characterized at VIN = VINSW1x = 3.6 V, VSW1AV = 1.2 V, ISW1AB = 100 mA, SW1AB_PWRSTG[2:0] = [111], and 25 °C,
unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
–
–
–
–
50
50
ISW1ABQ
–
–
18
235
–
–
µA
SW1A P-MOSFET RDSON
VINSW1A = 3.3 V
RONSW1AP
–
215
245
m
SW1A N-MOSFET RDSON
VINSW1A = 3.3 V
RONSW1AN
–
258
326
m
SW1A P-MOSFET Leakage Current
VINSW1A = 4.5 V
ISW1APQ
–
–
7.5
µA
SW1A N-MOSFET Leakage Current
VINSW1A = 4.5 V
ISW1ANQ
–
–
2.5
µA
SW1B P-MOSFET RDSON
VINSW1B = 3.3 V
RONSW1BP
–
215
245
m
SW1B N-MOSFET RDSON
VINSW1B = 3.3 V
RONSW1BN
–
258
326
m
SW1B P-MOSFET Leakage Current
VINSW1B = 4.5 V
ISW1BPQ
–
–
7.5
µA
SW1B N-MOSFET Leakage Current
VINSW1B = 4.5 V
ISW1BNQ
–
–
2.5
µA
RSW1ABDIS
–
600
–
SW1A/B (SINGLE PHASE) (CONTINUED)
Transient Load Regulation
• Transient load = 0 to 1.25 A, di/dt = 100 mA/s
Overshoot
Undershoot
Quiescent Current
PFM Mode
APS Mode
Discharge Resistance
VSW1ABLOTR
mV
Notes
38. Current rating of SW1AB supports the Power Virus mode of operation of the i.MX6X processor.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
45
Functional Block Requirements and Behaviors
Power Generation
SW1AB Single Phase
100
90
Efficiency (%)
80
70
)
60
(%
yc
n 50
ie
ci
ff 40
E
30
PFM ‐ Vout = 1.2V
20
APS ‐ Vout = 1.2V
10
PWM ‐ Vout = 1.2v
0
0.1
1
10
100
1000
Load Current (mA)
Figure 12. SW1AB Efficiency Waveforms
6.4.4.4
SW2
SW2 is a single phase, 1.5 A rated buck regulator. Table 28 describes the modes, and Table 29 show the options for the
SWxMODE[3:0] bits.
Figure 13 shows the block diagram and the external component connections for SW2 regulator.
VIN
SW2IN
SW2MODE
ISENSE
CINSW2
SW2
Controller
SW2LX
Driver
LSW2
COSW2
SW2FAULT
EP
Internal
Compensation
SW2FB
I2C
Interface
I2C
Z2
Z1
EA
VREF
DAC
Figure 13. SW2 Block Diagram
SW2 Setup and Control Registers
SW2 output voltage is programmable from 0.400 to 3.300 V; however, bit SW2[6] in register SW2VOLT is read-only during
normal operation. Its value is determined by the default configuration, or may be changed by using the OTP registers. Therefore,
once SW2[6] is set to “0”, the output will be limited to the lower output voltages from 0.400 to 1.975 V with 25 mV increments, as
determined by bits SW2[5:0]. Likewise, once bit SW2[6] is set to “1”, the output voltage will be limited to the higher output voltage
range from 0.800 to 3.300 V with 50 mV increments, as determined by bits SW2[5:0].
In order to optimize the performance of the regulator, it is recommended that only voltages from 2.000 to 3.300 V be used in the
high range, and the lower range be used for voltages from 0.400 to 1.975 V.
The output voltage set point is independently programmed for Normal, Standby, and Sleep mode by setting the SW2[5:0],
SW2STBY[5:0] and SW2OFF[5:0] bits, respectively. However, the initial state of bit SW2[6] will be copied into bits SW2STBY[6],
and SW2OFF[6] bits. Therefore, the output voltage range will remain the same in all three operating modes. Table 48 shows the
output voltage coding valid for SW2. Note: Output voltages of 0.6 V and below are not supported.
PF0200Z
46
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 48. SW2 Output Voltage Configuration
Low Output Voltage Range(39)
High Output Voltage Range
Set Point
SW2[6:0]
SW2STBY[6:0]
SW2OFF[6:0]
SW2 Output
Set Point
SW2[6:0]
SW2STBY[6:0]
SW2OFF[6:0]
SW2 Output
0
0000000
0.4000
64
1000000
0.8000
1
0000001
0.4250
65
1000001
0.8500
2
0000010
0.4500
66
1000010
0.9000
3
0000011
0.4750
67
1000011
0.9500
4
0000100
0.5000
68
1000100
1.0000
5
0000101
0.5250
69
1000101
1.0500
6
0000110
0.5500
70
1000110
1.1000
7
0000111
0.5750
71
1000111
1.1500
8
0001000
0.6000
72
1001000
1.2000
9
0001001
0.6250
73
1001001
1.2500
10
0001010
0.6500
74
1001010
1.3000
11
0001011
0.6750
75
1001011
1.3500
12
0001100
0.7000
76
1001100
1.4000
13
0001101
0.7250
77
1001101
1.4500
14
0001110
0.7500
78
1001110
1.5000
15
0001111
0.7750
79
1001111
1.5500
16
0010000
0.8000
80
1010000
1.6000
17
0010001
0.8250
81
1010001
1.6500
18
0010010
0.8500
82
1010010
1.7000
19
0010011
0.8750
83
1010011
1.7500
20
0010100
0.9000
84
1010100
1.8000
21
0010101
0.9250
85
1010101
1.8500
22
0010110
0.9500
86
1010110
1.9000
23
0010111
0.9750
87
1010111
1.9500
24
0011000
1.0000
88
1011000
2.0000
25
0011001
1.0250
89
1011001
2.0500
26
0011010
1.0500
90
1011010
2.1000
27
0011011
1.0750
91
1011011
2.1500
28
0011100
1.1000
92
1011100
2.2000
29
0011101
1.1250
93
1011101
2.2500
30
0011110
1.1500
94
1011110
2.3000
31
0011111
1.1750
95
1011111
2.3500
32
0100000
1.2000
96
1100000
2.4000
33
0100001
1.2250
97
1100001
2.4500
34
0100010
1.2500
98
1100010
2.5000
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
47
Functional Block Requirements and Behaviors
Power Generation
Table 48. SW2 Output Voltage Configuration (continued)
Low Output Voltage Range(39)
High Output Voltage Range
Set Point
SW2[6:0]
SW2STBY[6:0]
SW2OFF[6:0]
SW2 Output
Set Point
SW2[6:0]
SW2STBY[6:0]
SW2OFF[6:0]
SW2 Output
35
0100011
1.2750
99
1100011
2.5500
36
0100100
1.3000
100
1100100
2.6000
37
0100101
1.3250
101
1100101
2.6500
38
0100110
1.3500
102
1100110
2.7000
39
0100111
1.3750
103
1100111
2.7500
40
0101000
1.4000
104
1101000
2.8000
41
0101001
1.4250
105
1101001
2.8500
42
0101010
1.4500
106
1101010
2.9000
43
0101011
1.4750
107
1101011
2.9500
44
0101100
1.5000
108
1101100
3.0000
45
0101101
1.5250
109
1101101
3.0500
46
0101110
1.5500
110
1101110
3.1000
47
0101111
1.5750
111
1101111
3.1500
48
0110000
1.6000
112
1110000
3.2000
49
0110001
1.6250
113
1110001
3.2500
50
0110010
1.6500
114
1110010
3.3000
51
0110011
1.6750
115
1110011
Reserved
52
0110100
1.7000
116
1110100
Reserved
53
0110101
1.7250
117
1110101
Reserved
54
0110110
1.7500
118
1110110
Reserved
55
0110111
1.7750
119
1110111
Reserved
56
0111000
1.8000
120
1111000
Reserved
57
0111001
1.8250
121
1111001
Reserved
58
0111010
1.8500
122
1111010
Reserved
59
0111011
1.8750
123
1111011
Reserved
60
0111100
1.9000
124
1111100
Reserved
61
0111101
1.9250
125
1111101
Reserved
62
0111110
1.9500
126
1111110
Reserved
63
0111111
1.9750
127
1111111
Reserved
Notes
39. For voltages less than 2.0 V, only use set points 0 to 63
Setup and control of SW2 is done through I2C registers listed in Table 49, and a detailed description of each one of the registers
is provided in Tables 50 to Table 54.
PF0200Z
48
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 49. SW2 Register Summary
Register
Address
Description
SW2VOLT
0x35
Output voltage set point on normal operation
SW2STBY
0x36
Output voltage set point on Standby
SW2OFF
0x37
Output voltage set point on Sleep
SW2MODE
0x38
Switching Mode selector register
SW2CONF
0x39
DVS, Phase, Frequency, and ILIM configuration
Table 50. Register SW2VOLT - ADDR 0x35
Name
Bit #
R/W
Default
Description
SW2
5:0
R/W
0x00
Sets the SW2 output voltage during normal operation
mode. See Table 48 for all possible configurations.
SW2
6
R
0x00
Sets the operating output voltage range for SW2. Set
during OTP or TBB configuration only. See Table 48
for all possible configurations.
UNUSED
7
–
0x00
UNUSED
Table 51. Register SW2STBY - ADDR 0x36
Name
SW2STBY
Bit #
R/W
Default
Description
5:0
R/W
0x00
Sets the SW2 output voltage during Standby mode.
See Table 48 for all possible configurations.
SW2STBY
6
R
0x00
Sets the operating output voltage range for SW2 on
Standby mode. This bit inherits the value configured
on bit SW2[6] during OTP or TBB configuration. See
Table 48 for all possible configurations.
UNUSED
7
–
0x00
UNUSED
Table 52. Register SW2OFF - ADDR 0x37
Name
SW2OFF
Bit #
R/W
Default
Description
5:0
R/W
0x00
Sets the SW2 output voltage during Sleep mode. See
Table 48 for all possible configurations.
SW2OFF
6
R
0x00
Sets the operating output voltage range for SW2 on
Sleep mode. This bit inherits the value configured on
bit SW2[6] during OTP or TBB configuration. See
Table 48 for all possible configurations.
UNUSED
7
–
0x00
UNUSED
Table 53. Register SW2MODE - ADDR 0x38
Name
Bit #
R/W
Default
3:0
R/W
0x80
Sets the SW2 switching operation mode.
See Table 28 for all possible configurations.
UNUSED
4
–
0x00
UNUSED
SW2OMODE
5
R/W
0x00
Set status of SW2 when in Sleep mode
0 = OFF
1 = PFM
7:6
–
0x00
UNUSED
SW2MODE
UNUSED
Description
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
49
Functional Block Requirements and Behaviors
Power Generation
Table 54. Register SW2CONF - ADDR 0x39
Name
Bit #
R/W
Default
Description
SW2ILIM
0
R/W
0x00
SW2 current limit level selection
0 = High level current limit
1 = Low level current limit
UNUSED
1
R/W
0x00
Unused
SW2FREQ
3:2
R/W
0x00
SW2 switching frequency selector.
See Table 36.
SW2PHASE
5:4
R/W
0x00
SW2 Phase clock selection.
See Table 34.
SW2DVSSPEED
7:6
R/W
0x00
SW2 DVS speed selection.
See Table 33.
SW2 External Components
Table 55. SW2 External Component Recommendations
Components
SW2 Input capacitor
(40)
SW2 Decoupling input capacitor
CINSW2
CIN2HF
Description
(40)
COSW2(40)
SW2 Output capacitor
LSW2
SW2 Inductor
Values
4.7 F
0.1 F
2 x 22 F
1.0 H
DCR = 50 m
ISAT = 2.65 A
Notes
40. Use X5R or X7R capacitors.
PF0200Z
50
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
SW2 Specifications
Table 56. SW2 Electrical Characteristics
All parameters are specified at TA = -40 to 85 °C, VIN = VINSW2 = 3.6 V, VSW2 = 3.15 V, ISW2 = 100 mA,
SW2_PWRSTG[2:0] = [111], typical external component values, fSW2 = 2.0 MHz, unless otherwise noted. Typical values are
characterized at VIN = VINSW2 = 3.6 V, VSW2 = 3.15 V, ISW2 = 100 mA, SW2_PWRSTG[2:0] = [111], and 25 °C, unless otherwise
noted.
Parameter
Symbol
Min
Typ
Max
Unit
VINSW2
2.8
–
4.5
V
VSW2
–
Table 48
–
V
-25
-3.0%
-6.0%
–
–
–
25
3.0%
6.0%
-65
-45
-3.0%
-3.0%
–
–
–
–
65
45
3.0%
3.0%
ISW2
–
–
1500
mA
ISW2LIM
2.1
1.57
3.0
2.25
3.9
2.93
A
Start-up Overshoot
ISW2 = 0.0 mA
DVS clk = 25 mV/4 s, VIN = VINSW2 = 4.5 V
VSW2OSH
–
–
66
mV
Turn-on Time
Enable to 90% of end value
ISW2 = 0.0 mA
DVS clk = 50 mV/8 s, VIN = VINSW2 = 4.5 V
tONSW2
–
–
550
µs
–
–
–
1.0
2.0
4.0
–
–
–
–
–
–
–
–
–
94
95
96
94
92
89
–
–
–
–
–
–
VSW2
–
10
–
mV
Line Regulation (APS, PWM)
VSW2LIR
–
–
20
mV
DC Load Regulation (APS, PWM)
VSW2LOR
–
–
20
mV
SWITCH MODE SUPPLY SW2
Operating Input Voltage(41)
Nominal Output Voltage
Output Voltage Accuracy
• PWM, APS, 2.8 V < VIN < 4.5 V, 0 < ISW2 < 1.5 A
0.625 V < VSW2 < 0.85 V
0.875 V < VSW2 < 1.975 V
2.0 V < VSW2 < 3.3 V
•
PFM, 2.8 V < VIN < 4.5 V, 0 < ISW2 50 mA
0.625 V < VSW2 < 0.675 V
0.7 V < VSW2 < 0.85 V
0.875 V < VSW2 < 1.975 V
2.0 V < VSW2 < 3.3 V
Rated Output Load Current (42)
2.8 V < VIN < 4.5 V, 0.625 V < VSW2 < 3.3 V
Current Limiter Peak Current Detection
• Current through Inductor
SW2ILIM = 0
SW2ILIM = 1
VSW2ACC
Switching Frequency
SW2FREQ[1:0] = 00
SW2FREQ[1:0] = 01
SW2FREQ[1:0] = 10
fSW2
Efficiency
• VIN = 3.6 V, fSW2 = 2.0 MHz, LSW2 = 1.0 H
PFM, 3.15 V, 1.0 mA
PFM, 3.15 V, 50 mA
APS, PWM, 3.15 V, 400 mA
APS, PWM, 3.15 V, 600 mA
APS, PWM, 3.15 V, 1000 mA
APS, PWM, 3.15 V, 1500 mA
SW2
Output Ripple
mV
%
MHz
%
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
51
Functional Block Requirements and Behaviors
Power Generation
Table 56. SW2 Electrical Characteristics (continued)
All parameters are specified at TA = -40 to 85 °C, VIN = VINSW2 = 3.6 V, VSW2 = 3.15 V, ISW2 = 100 mA,
SW2_PWRSTG[2:0] = [111], typical external component values, fSW2 = 2.0 MHz, unless otherwise noted. Typical values are
characterized at VIN = VINSW2 = 3.6 V, VSW2 = 3.15 V, ISW2 = 100 mA, SW2_PWRSTG[2:0] = [111], and 25 °C, unless otherwise
noted.
Parameter
Symbol
Min
Typ
Max
–
–
–
–
50
50
–
–
–
23
145
305
–
–
–
Unit
SWITCH MODE SUPPLY SW2 (CONTINUED)
Transient Load Regulation
• Transient load = 0.0 mA to 1.0 A, di/dt = 100 mA/s
Overshoot
Undershoot
VSW2LOTR
Quiescent Current
PFM Mode
APS Mode (Low output voltage settings)
APS Mode (High output voltage settings)
ISW2Q
mV
µA
SW2 P-MOSFET RDSON
at VIN = VINSW2 = 3.3 V
RONSW2P
–
190
209
m
SW2 N-MOSFET RDSON
at VIN = VINSW2 = 3.3 V
RONSW2N
–
212
255
m
SW2 P-MOSFET Leakage Current
VIN = VINSW2 = 4.5 V
ISW2PQ
–
–
12
µA
SW2 N-MOSFET Leakage Current
VIN = VINSW2 = 4.5 V
ISW2NQ
–
–
4.0
µA
Discharge Resistance
RSW2DIS
–
600
–
Notes
41. When output is set to > 2.6 V the output will follow the input down when VIN gets near 2.8 V.
42.
The higher output voltages available depend on the voltage drop in the conduction path as given by the following equation:
(VINSW2 - VSW2) = ISW2* (DCR of Inductor +RONSW2P + PCB trace resistance).
100
90
80
PFM ‐ Vout = 3.15V
20
APS ‐ Vout = 3.15V
Efficiency (%)
70
)
%
(y 60
c
n 50
ie
ci
ff 40
E
30
10
PWM ‐ Vout = 3.15V
0
0.1
1
10
100
1000
Load Current (mA)
Figure 14. SW2 Efficiency Waveforms
PF0200Z
52
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
6.4.4.5
SW3A/B
SW3A/B are 1.25 to 2.5 A rated buck regulators, depending on the configuration. Table 28 describes the available switching
modes and Table 29 show the actual configuration options for the SW3xMODE[3:0] bits.
SW3A/B can be configured in various phasing schemes, depending on the desired cost/performance trade-offs. The following
configurations are available:
• A single phase
• Independent regulators
The desired configuration is programmed in OTP by using the SW3_CONFIG[1:0] bits.Table 57 shows the options for the
SW3CFG[1:0] bits.
Table 57. SW3 Configuration
SW3_CONFIG[1:0]
Description
00
A/B Single Phase
01
A/B Single Phase
10
Reserved
11
A/B Independent
SW3A/B Single Phase
In this configuration, SW3ALX and SW3BLX are connected in single phase with a single inductor a shown in Figure 15. This
configuration reduces cost and component count. Feedback is taken from the SW3AFB pin and the SW3BFB pin must be left
open. Although control is from SW3A, registers of both regulators, SW3A and SW3B, must be identically set.
VIN
SW3AIN
SW3AMODE
ISENSE
CINSW3A
SW3
SW3ALX
LSW3A
Controller
Driver
COSW3A
SW3AFAULT
Internal
Compensation
SW3AFB
I2C
Z2
Z1
VREF
EA
DAC
I2C
Interface
VIN
SW3BIN
SW3BMODE
ISENSE
CINSW3B
SW3BLX
Controller
Driver
SW3BFAULT
EP
I2C
Internal
Compensation
SW3BFB
Z2
VREF
Z1
EA
DAC
Figure 15. SW3A/B Single Phase Block Diagram
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
53
Functional Block Requirements and Behaviors
Power Generation
SW3A - SW3B Independent Outputs
SW3A and SW3B can be configured as independent outputs as shown in Figure 16, providing flexibility for applications requiring
more voltage rails with less current capability. Each output is configured and controlled independently by its respective I2C
registers as shown in Table 59.
VIN
SW3AIN
SW3AMODE
ISENSE
CINSW3A
SW3A
SW3ALX
LSW3A
Controller
Driver
COSW3A
SW3AFAULT
Internal
Compensation
SW3AFB
I2C
Z2
Z1
VREF
EA
DAC
VIN
SW3BIN
I2C
Interface
ISENSE
CINSW3B
SW3B
SW3BLX
LSW3B
COSW3B
SW3BMODE
Controller
Driver
SW3BFAULT
EP
Internal
Compensation
SW3BFB
I2C
Z2
Z1
EA
VREF
DAC
Figure 16. SW3A/B Independent Output Block Diagram
SW3A/B Setup and Control Registers
SW3A/B output voltage is programmable from 0.400 to 3.300 V; however, bit SW3x[6] in register SW3xVOLT is read-only during
normal operation. Its value is determined by the default configuration, or may be changed by using the OTP registers. Therefore,
once SW3x[6] is set to “0”, the output will be limited to the lower output voltages from 0.40 to 1.975 V with 25 mV increments, as
determined by bits SW3x[5:0]. Likewise, once bit SW3x[6] is set to "1", the output voltage will be limited to the higher output
voltage range from 0.800 to 3.300 V with 50 mV increments, as determined by bits SW3x[5:0].
In order to optimize the performance of the regulator, it is recommended that only voltages from 2.00 to 3.300 V be used in the
high range and that that the lower range be used for voltages from 0.400 to 1.975 V.
The output voltage set point is independently programmed for Normal, Standby, and Sleep mode by setting the SW3x[5:0],
SW3xSTBY[5:0], and SW3xOFF[5:0] bits respectively; however, the initial state of the SW3x[6] bit will be copied into the
SW3xSTBY[6] and SW3xOFF[6] bits. Therefore, the output voltage range will remain the same on all three operating modes.
Table 58 shows the output voltage coding valid for SW3x. Note: Output voltages of 0.6 V and below are not supported.
PF0200Z
54
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 58. SW3A/B Output Voltage Configuration
Low Output Voltage Range(43)
High Output Voltage Range
Set Point
SW3x[6:0]
SW3xSTBY[6:0]
SW3xOFF[6:0]
SW3x Output
Set Point
SW3x[6:0]
SW3xSTBY[6:0]
SW3xOFF[6:0]
SW3xOutput
0
0000000
0.4000
64
1000000
0.8000
1
0000001
0.4250
65
1000001
0.8500
2
0000010
0.4500
66
1000010
0.9000
3
0000011
0.4750
67
1000011
0.9500
4
0000100
0.5000
68
1000100
1.0000
5
0000101
0.5250
69
1000101
1.0500
6
0000110
0.5500
70
1000110
1.1000
7
0000111
0.5750
71
1000111
1.1500
8
0001000
0.6000
72
1001000
1.2000
9
0001001
0.6250
73
1001001
1.2500
10
0001010
0.6500
74
1001010
1.3000
11
0001011
0.6750
75
1001011
1.3500
12
0001100
0.7000
76
1001100
1.4000
13
0001101
0.7250
77
1001101
1.4500
14
0001110
0.7500
78
1001110
1.5000
15
0001111
0.7750
79
1001111
1.5500
16
0010000
0.8000
80
1010000
1.6000
17
0010001
0.8250
81
1010001
1.6500
18
0010010
0.8500
82
1010010
1.7000
19
0010011
0.8750
83
1010011
1.7500
20
0010100
0.9000
84
1010100
1.8000
21
0010101
0.9250
85
1010101
1.8500
22
0010110
0.9500
86
1010110
1.9000
23
0010111
0.9750
87
1010111
1.9500
24
0011000
1.0000
88
1011000
2.0000
25
0011001
1.0250
89
1011001
2.0500
26
0011010
1.0500
90
1011010
2.1000
27
0011011
1.0750
91
1011011
2.1500
28
0011100
1.1000
92
1011100
2.2000
29
0011101
1.1250
93
1011101
2.2500
30
0011110
1.1500
94
1011110
2.3000
31
0011111
1.1750
95
1011111
2.3500
32
0100000
1.2000
96
1100000
2.4000
33
0100001
1.2250
97
1100001
2.4500
34
0100010
1.2500
98
1100010
2.5000
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
55
Functional Block Requirements and Behaviors
Power Generation
Table 58. SW3A/B Output Voltage Configuration (continued)
Low Output Voltage Range(43)
High Output Voltage Range
Set Point
SW3x[6:0]
SW3xSTBY[6:0]
SW3xOFF[6:0]
SW3x Output
Set Point
SW3x[6:0]
SW3xSTBY[6:0]
SW3xOFF[6:0]
SW3xOutput
35
0100011
1.2750
99
1100011
2.5500
36
0100100
1.3000
100
1100100
2.6000
37
0100101
1.3250
101
1100101
2.6500
38
0100110
1.3500
102
1100110
2.7000
39
0100111
1.3750
103
1100111
2.7500
40
0101000
1.4000
104
1101000
2.8000
41
0101001
1.4250
105
1101001
2.8500
42
0101010
1.4500
106
1101010
2.9000
43
0101011
1.4750
107
1101011
2.9500
44
0101100
1.5000
108
1101100
3.0000
45
0101101
1.5250
109
1101101
3.0500
46
0101110
1.5500
110
1101110
3.1000
47
0101111
1.5750
111
1101111
3.1500
48
0110000
1.6000
112
1110000
3.2000
49
0110001
1.6250
113
1110001
3.2500
50
0110010
1.6500
114
1110010
3.3000
51
0110011
1.6750
115
1110011
Reserved
52
0110100
1.7000
116
1110100
Reserved
53
0110101
1.7250
117
1110101
Reserved
54
0110110
1.7500
118
1110110
Reserved
55
0110111
1.7750
119
1110111
Reserved
56
0111000
1.8000
120
1111000
Reserved
57
0111001
1.8250
121
1111001
Reserved
58
0111010
1.8500
122
1111010
Reserved
59
0111011
1.8750
123
1111011
Reserved
60
0111100
1.9000
124
1111100
Reserved
61
0111101
1.9250
125
1111101
Reserved
62
0111110
1.9500
126
1111110
Reserved
63
0111111
1.9750
127
1111111
Reserved
Notes
43. For voltages less than 2.0 V, only use set points 0 to 63.
PF0200Z
56
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 59 provides a list of registers used to configure and operate SW3A/B. A detailed description on each of these register is
provided on Tables 60 through Table 69.
Table 59. SW3AB Register Summary
Register
Address
Output
SW3AVOLT
0x3C
SW3A Output voltage set point on normal operation
SW3ASTBY
0x3D
SW3A Output voltage set point on Standby
SW3AOFF
0x3E
SW3A Output voltage set point on Sleep
SW3AMODE
0x3F
SW3A Switching mode selector register
SW3ACONF
0x40
SW3A DVS, phase, frequency and ILIM configuration
SW3BVOLT
0x43
SW3B Output voltage set point on normal operation
SW3BSTBY
0x44
SW3B Output voltage set point on Standby
SW3BOFF
0x45
SW3B Output voltage set point on Sleep
SW3BMODE
0x46
SW3B Switching mode selector register
SW3BCONF
0x47
SW3B DVS, phase, frequency and ILIM configuration
Table 60. Register SW3AVOLT - ADDR 0x3C
Name
SW3A
Bit #
R/W
Default
Description
5:0
R/W
0x00
Sets the SW3A output voltage (Independent) or
SW3A/B output voltage (Single phase), during
normal operation mode. See Table 58 for all
possible configurations.
SW3A
6
R
0x00
Sets the operating output voltage range for SW3A
(Independent) or SW3A/B (Single phase). Set
during OTP or TBB configuration only. See
Table 58 for all possible configurations.
UNUSED
7
–
0x00
UNUSED
Table 61. Register SW3ASTBY - ADDR 0x3D
Name
SW3ASTBY
Bit #
5:0
R/W
R/W
Default
Description
0x00
Sets the SW3A output voltage (Independent) or
SW3A/B output voltage (Single phase), during
Standby mode. See Table 58 for all possible
configurations.
SW3ASTBY
6
R
0x00
Sets the operating output voltage range for SW3A
(Independent) or SW3A/B (Single phase) on
Standby mode. This bit inherits the value
configured on bit SW3A[6] during OTP or TBB
configuration. See Table 58 for all possible
configurations.
UNUSED
7
–
0x00
UNUSED
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
57
Functional Block Requirements and Behaviors
Power Generation
Table 62. Register SW3AOFF - ADDR 0x3E
Name
SW3AOFF
Bit #
5:0
R/W
R/W
Default
Description
0x00
Sets the SW3A output voltage (Independent) or
SW3A/B output voltage (Single phase), during
Sleep mode. See Table 58 for all possible
configurations.
SW3AOFF
6
R
0x00
Sets the operating output voltage range for SW3A
(Independent) or SW3A/B (Single phase) on
Sleep mode. This bit inherits the value configured
on bit SW3A[6] during OTP or TBB configuration.
See Table 58 for all possible configurations.
UNUSED
7
–
0x00
UNUSED
Table 63. Register SW3AMODE - ADDR 0x3F
Name
SW3AMODE
UNUSED
SW3AOMODE
UNUSED
Bit #
R/W
Default
Description
3:0
R/W
0x80
Sets the SW3A (Independent) or SW3A/B (Single
phase) switching operation mode.
See Table 28 for all possible configurations.
4
–
0x00
UNUSED
5
R/W
0x00
Set status of SW3A (Independent) or SW3A/B
(Single phase) when in Sleep mode.
0 = OFF
1 = PFM
7:6
–
0x00
UNUSED
Table 64. Register SW3ACONF - ADDR 0x40
Name
Bit #
R/W
Default
Description
SW3AILIM
0
R/W
0x00
SW3A current limit level selection
0 = High level current limit
1 = Low level current limit
UNUSED
1
R/W
0x00
Unused
SW3AFREQ
3:2
R/W
0x00
SW3A switching frequency selector. See
Table 36.
SW3APHASE
5:4
R/W
0x00
SW3A Phase clock selection. See Table 34.
SW3ADVSSPEED
7:6
R/W
0x00
SW3A DVS speed selection. See Table 33.
Table 65. Register SW3BVOLT - ADDR 0x43
Name
Bit #
R/W
Default
Description
SW3B
5:0
R/W
0x00
Sets the SW3B output voltage (Independent)
during normal operation mode. See Table 58 for
all possible configurations.
SW3B
6
R
0x00
Sets the operating output voltage range for SW3B
(Independent). Set during OTP or TBB
configuration only. See Table 58 for all possible
configurations.
UNUSED
7
–
0x00
UNUSED
PF0200Z
58
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 66. Register SW3BSTBY - ADDR 0x44
Name
SW3BSTBY
Bit #
R/W
Default
Description
5:0
R/W
0x00
Sets the SW3B output voltage (Independent)
during Standby mode. See Table 58 for all
possible configurations.
SW3BSTBY
6
R
0x00
Sets the operating output voltage range for SW3B
(Independent) on Standby mode. This bit inherits
the value configured on bit SW3B[6] during OTP
or TBB configuration. See Table 58 for all
possible configurations.
UNUSED
7
–
0x00
UNUSED
Table 67. Register SW3BOFF - ADDR 0x45
Name
SW3BOFF
Bit #
R/W
Default
Description
5:0
R/W
0x00
Sets the SW3B output voltage (Independent)
during Sleep mode. See Table 58 for all possible
configurations.
SW3BOFF
6
R
0x00
Sets the operating output voltage range for SW3B
(Independent) on Sleep mode. This bit inherits
the value configured on bit SW3B[6] during OTP
or TBB configuration. See Table 58 for all
possible configurations.
UNUSED
7
–
0x00
UNUSED
Table 68. Register SW3BMODE - ADDR 0x46
Name
SW3BMODE
UNUSED
SW3BOMODE
UNUSED
Bit #
R/W
Default
Description
3:0
R/W
0x80
Sets the SW3B (Independent) switching
operation mode. See Table 28 for all possible
configurations.
4
–
0x00
UNUSED
5
R/W
0x00
Set status of SW3B (Independent) when in Sleep
mode.
0 = OFF
1 = PFM
7:6
–
0x00
UNUSED
Table 69. Register SW3BCONF - ADDR 0x47
Name
Bit #
R/W
Default
Description
SW3BILIM
0
R/W
0x00
SW3B current limit level selection
0 = High level Current limit
1 = Low level Current limit
UNUSED
1
R/W
0x00
Unused
SW3BFREQ
3:2
R/W
0x00
SW3B switching frequency selector. See Table 36.
SW3BPHASE
5:4
R/W
0x00
SW3B Phase clock selection. See Table 34.
SW3BDVSSPEED
7:6
R/W
0x00
SW3B DVS speed selection. See Table 33.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
59
Functional Block Requirements and Behaviors
Power Generation
SW3A/B External Components
Table 70. SW3A/B External Component Requirements
Mode
Components
CINSW3A(44)
Description
SW3A/B Single
Phase
SW3A Independent
SW3B Independent
SW3A Input capacitor
4.7 F
4.7 F
(44)
SW3A Decoupling input capacitor
0.1 F
0.1 F
(44)
SW3B Input capacitor
4.7 F
4.7 F
(44)
SW3B Decoupling input capacitor
0.1 F
0.1 F
COSW3A
(44)
SW3A Output capacitor
4 x 22 F
2 x 22 F
COSW3B
(44)
SW3B Output capacitor
–
2 x 22 F
CIN3AHF
CINSW3B
CIN3BHF
LSW3A
SW3A Inductor
1.0 H
DCR = 50 m
ISAT = 3.9 A
1.0 H
DCR = 60 m
ISAT = 3.0 A
LSW3B
SW3B Inductor
–
1.0 H
DCR = 60 m
ISAT = 3.0 A
Notes
44. Use X5R or X7R capacitors.
SW3A/B Specifications
Table 71. SW3A/B Electrical Characteristics
All parameters are specified at TA = -40 to 85 °C, VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], typical external component values, fSW3x = 2.0 MHz, single phase and independent mode unless,
otherwise noted. Typical values are characterized at VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
VINSW3x
VSW3x
Unit
2.8
–
4.5
V
-
Table 58
-
V
-25
-3.0%
-6.0%
–
–
–
25
3.0%
6.0%
-65
-45
-3.0%
-3.0%
–
–
–
–
65
45
3.0%
3.0%
–
–
–
–
2500
1250
SWITCH MODE SUPPLY SW3A/B
Operating Input Voltage(45)
Nominal Output Voltage
Output Voltage Accuracy
• PWM, APS 2.8 V < VIN < 4.5 V, 0 < ISW3x < ISW3xMAX
0.625 V < VSW3x < 0.85 V
0.875 V < VSW3x < 1.975 V
2.0 V < VSW3x < 3.3 V
•
PFM , steady state (2.8 V < VIN < 4.5 V, 0 < ISW3x < 50 mA)
0.625 V < VSW3x < 0.675 V
0.7 V < VSW3x < 0.85 V
0.875 V < VSW3x < 1.975 V
2.0 V < VSW3x < 3.3 V
Rated Output Load Current (46)
• 2.8 V < VIN < 4.5 V, 0.625 V < VSW3x < 3.3 V
PWM, APS mode single phase
PWM, APS mode independent (per phase)
VSW3xACC
ISW3x
mV
%
mA
PF0200Z
60
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 71. SW3A/B Electrical Characteristics (continued)
All parameters are specified at TA = -40 to 85 °C, VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], typical external component values, fSW3x = 2.0 MHz, single phase and independent mode unless,
otherwise noted. Typical values are characterized at VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
3.5
2.7
5.0
3.8
6.5
4.9
Unit
SWITCH MODE SUPPLY SW3A/B (CONTINUED)
Current Limiter Peak Current Detection
• Single phase (Current through inductor)
SW3xILIM = 0
SW3xILIM = 1
•
A
ISW3xLIM
Independent mode (Current through inductor per phase)
SW3xILIM = 0
SW3xILIM = 1
1.8
1.3
2.5
1.9
3.3
2.5
Start-up Overshoot
ISW3x = 0.0 mA
DVS clk = 25 mV/4 s, VIN = VINSW3x = 4.5 V
VSW3xOSH
–
–
66
mV
Turn-on Time
Enable to 90% of end value
ISW3x = 0 mA
DVS clk = 25 mV/4 s, VIN = VINSW3x = 4.5 V
tONSW3x
–
–
500
µs
–
–
–
1.0
2.0
4.0
–
–
–
–
–
–
–
–
–
84
85
85
84
80
74
–
–
–
–
–
–
Switching Frequency
SW3xFREQ[1:0] = 00
SW3xFREQ[1:0] = 01
SW3xFREQ[1:0] = 10
fSW3x
MHz
Efficiency (Single Phase)
• fSW3 = 2.0 MHz, LSW3x 1.0 H
PFM, 1.5 V, 1.0 mA
PFM, 1.5 V, 50 mA
APS, PWM 1.5 V, 500 mA
APS, PWM 1.5 V, 750 mA
APS, PWM 1.5 V, 1250 mA
APS, PWM 1.5 V, 2500 mA
SW3AB
Output Ripple
VSW3x
–
10
–
mV
Line Regulation (APS, PWM)
VSW3xLIR
–
–
20
mV
DC Load Regulation (APS, PWM)
VSW3xLOR
–
–
20
mV
Transient Load Regulation
• Transient Load = 0.0 mA to ISW3x/2, di/dt = 100 mA/s
Overshoot
Undershoot
VSW3xLOTR
–
–
–
–
50
50
–
–
–
–
–
22
300
50
250
150
–
–
–
–
–
215
245
258
326
–
7.5
Quiescent Current
PFM Mode (Single Phase)
APS Mode (Single Phase)
PFM Mode (Independent mode)
APS Mode (SW3A Independent mode)
APS Mode (SW3B Independent mode)
ISW3xQ
SW3A P-MOSFET RDSON
at VIN = VINSW3A = 3.3 V
RONSW3AP
–
SW3A N-MOSFET RDSON
at VIN = VINSW3A = 3.3 V
RONSW3AN
–
ISW3APQ
–
SW3A P-MOSFET Leakage Current
VIN = VINSW3A = 4.5 V
%
mV
µA
m
m
µA
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
61
Functional Block Requirements and Behaviors
Power Generation
Table 71. SW3A/B Electrical Characteristics (continued)
All parameters are specified at TA = -40 to 85 °C, VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], typical external component values, fSW3x = 2.0 MHz, single phase and independent mode unless,
otherwise noted. Typical values are characterized at VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
ISW3ANQ
–
–
2.5
µA
SW3B P-MOSFET RDS(on)
at VIN = VINSW3B = 3.3 V
RONSW3BP
–
215
245
SW3B N-MOSFET RDS(on)
at VIN = VINSW3B = 3.3 V
RONSW3BN
–
258
326
SW3B P-MOSFET Leakage Current
VIN = VINSW3B = 4.5 V
ISW3BPQ
–
–
7.5
µA
SW3B N-MOSFET Leakage Current
VIN = VINSW3B = 4.5 V
ISW3BPQ
–
–
2.5
µA
Discharge Resistance
RSW3xDIS
–
600
–
SWITCH MODE SUPPLY SW3A/B (CONTINUED)
SW3A N-MOSFET Leakage Current
VIN = VINSW3A = 4.5 V
m
m
Notes
45. When output is set to > 2.6 V the output will follow the input down when VIN gets near 2.8 V.
46.
The higher output voltages available depend on the voltage drop in the conduction path as given by the following equation:
(VINSW3x - VSW3x) = ISW3x* (DCR of Inductor +RONSW3xP + PCB trace resistance).
100
90
80
PFM ‐ Vout = 1.5V
20
APS ‐ Vout = 1.5V
Efficiency (%)
70
)
(%
y 60
c
n 50
e
ic
if 40
fE
30
10
PWM ‐ Vout = 1.5V
0
0.1
1
10
100
1000
Load Current (mA)
Figure 17. SW3AB Single Phase Efficiency Waveforms
PF0200Z
62
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
6.4.5
Boost Regulator
SWBST is a boost regulator with a programmable output from 5.0 to 5.15 V. SWBST can supply the VUSB regulator for the USB
PHY in OTG mode, as well as the VBUS voltage. Note that the parasitic leakage path for a boost regulator will cause the
SWBSTOUT and SWBSTFB voltage to be a Schottky drop below the input voltage whenever SWBST is disabled. The switching
NMOS transistor is integrated on-chip. Figure 18 shows the block diagram and component connection for the boost regulator.
VIN
CINBST
VOBST
LBST
SWBSTIN
DBST
SWBSTMODE
SWBSTLX
Driver
OC
RSENSE
EP
VREFSC
Controller
SWBSTFAULT
I2C
Interface
SC
VREFUV
UV
SWBSTFB
Internal
Compensation Z2
COSWBST
Z1
EA
VREF
Figure 18. Boost Regulator Architecture
6.4.5.1
SWBST Setup and Control
Boost regulator control is done through a single register SWBSTCTL described in Table 72. SWBST is included in the power-up
sequence if its OTP power-up timing bits, SWBST_SEQ[4:0], are not all zeros.
Table 72. Register SWBSTCTL - ADDR 0x66
Name
Bit #
SWBST1VOLT
SWBST1MODE
UNUSED
SWBST1STBYMODE
1:0
R/W
R/W
Default
Description
0x00
Set the output voltage for SWBST
00 = 5.000 V
01 = 5.050 V
10 = 5.100 V
11 = 5.150 V
3:2
R
0x02
Set the Switching mode on Normal operation
00 = OFF
01 = PFM
10 = Auto (Default)(47)
11 = APS
4
–
0x00
UNUSED
0x02
Set the Switching mode on Standby
00 = OFF
01 = PFM
10 = Auto (Default)(47)
11 = APS
6:5
R/W
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
63
Functional Block Requirements and Behaviors
Power Generation
Table 72. Register SWBSTCTL - ADDR 0x66 (continued)
Name
Bit #
R/W
Default
7
–
0x00
UNUSED
Description
UNUSED
Notes
47. In Auto mode, the controller automatically switches between PFM and APS modes depending on the load current.
The SWBST regulator starts up by default in the Auto mode, if SWBST is part of the startup sequence.
6.4.5.2
SWBST External Components
Table 73. SWBST External Component Requirements
Components
Description
Values
CINBST(48)
SWBST input capacitor
10 F
CINBSTHF(48)
SWBST decoupling input capacitor
0.1 F
COBST(48)
SWBST output capacitor
LSBST
SWBST inductor
DBST
SWBST boost diode
2 x 22 F
2.2 H
1.0 A, 20 V Schottky
Notes
48. Use X5R or X7R capacitors.
6.4.5.3
SWBST Specifications
Table 74. SWBST Electrical Specifications
All parameters are specified at TA = -40 to 85 °C, VIN = VINSWBST = 3.6 V, VSWBST = 5.0 V, ISWBST = 100 mA, typical external
component values, fSWBST = 2.0 MHz, otherwise noted. Typical values are characterized at VIN = VINSWBST = 3.6 V,
VSWBST = 5.0 V, ISWBST = 100 mA, and 25 °C, unless otherwise noted.
Parameters
Symbol
Min
Typ
Max
Units
VINSWBST
VSWBST
2.8
–
4.5
V
–
Table 72
–
V
VSWBSTACC
-4.0
–
3.0
%
VSWBST
–
–
120
mV
Vp-p
DC Load Regulation
0 < ISWBST < ISWBSTMAX
VSWBSTLOR
–
0.5
–
mV/
mA
DC Line Regulation
2.8 V VIN 4.5 V, ISWBST = ISWBSTMAX
VSWBSTLIR
–
50
–
mV
ISWBST
–
–
–
–
500
600
mA
ISWBSTQ
–
222
289
A
SWITCH MODE SUPPLY SWBST
Input Voltage Range
Nominal Output Voltage
Output Voltage Accuracy
2.8 V VIN 4.5 V
0 < ISWBST < ISWBSTMAX
Output Ripple
2.8 V VIN 4.5 V
0 < ISWBST < ISWBSTMAX, excluding reverse recovery of
Schottky diode
Continuous Load Current
2.8 V VIN 3.0 V
3.0 V VIN 4.5 V
Quiescent Current
AUTO
MOSFET on Resistance
RDSONBST
–
206
306
m
Peak Current Limit (49)
ISWBSTLIM
1400
2200
3200
mA
PF0200Z
64
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 74. SWBST Electrical Specifications (continued)
All parameters are specified at TA = -40 to 85 °C, VIN = VINSWBST = 3.6 V, VSWBST = 5.0 V, ISWBST = 100 mA, typical external
component values, fSWBST = 2.0 MHz, otherwise noted. Typical values are characterized at VIN = VINSWBST = 3.6 V,
VSWBST = 5.0 V, ISWBST = 100 mA, and 25 °C, unless otherwise noted.
Parameters
Symbol
Min
Typ
Max
Units
VSWBSTOSH
–
–
500
mV
Transient Load Response
ISWBST from 1.0 to 100 mA in 1.0 µs
Maximum transient Amplitude
VSWBSTTR
–
–
300
mV
Transient Load Response
ISWBST from 100 to 1.0 mA in 1.0 µs
Maximum transient Amplitude
VSWBSTTR
–
–
300
mV
Transient Load Response
ISWBST from 1.0 to 100 mA in 1.0 µs
Time to settle 80% of transient
tSWBSTTR
–
–
500
µs
Transient Load Response
ISWBST from 100 to 1.0 mA in 1.0 µs
Time to settle 80% of transient
tSWBSTTR
–
–
20
ms
NMOS Off Leakage
SWBSTIN = 4.5 V, SWBSTMODE [1:0] = 00
ISWBSTHSQ
–
1.0
5.0
µA
Turn-on Time
Enable to 90% of VSWBST, ISWBST = 0.0 mA
tONSWBST
–
–
2.0
ms
Switching Frequency
fSWBST
–
2.0
–
MHz
Efficiency
ISWBST = ISWBSTMAX
SWBST
–
86
–
%
Start-up Overshoot
ISWBST = 0.0 mA
SWITCH MODE SUPPLY SWBST (CONTINUED)
Notes
49. Only in Auto mode.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
65
Functional Block Requirements and Behaviors
Power Generation
6.4.6
LDO Regulators Description
This section describes the LDO regulators provided by the PF0200Z. All regulators use the main bandgap as reference. Refer
to Bias and References Block Description section for further information on the internal reference voltages.
A Low Power mode is automatically activated by reducing bias currents when the load current is less than I_Lmax/5. However,
the lowest bias currents may be attained by forcing the part into its Low Power mode by setting the VGENxLPWR bit. The use
of this bit is only recommended when the load is expected to be less than I_Lmax/50, otherwise performance may be degraded.
When a regulator is disabled, the output will be discharged by an internal pull-down. The pull-down is also activated when
RESETBMCU is low.
VINx
VINx
VREF
_
VGENxEN
+
VGENxLPWR
VGENx
VGENx
I2C
Interface
CGENx
VGENx
Discharge
Figure 19. General LDO Block Diagram
PF0200Z
66
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
6.4.6.1
Transient Response Waveforms
Idealized stimulus and response waveforms for transient line and transient load tests are depicted in Figure 20. Note that the
transient line and load response refers to the overshoot, or undershoot only, excluding the DC shift.
IMAX
ILOAD
IMAX/10
1.0 us
1.0 us
Transient Load Stimulus
IL = IMAX/10
IL = IMAX
Overshoot
VOUT
Undershoot
VOUT Transient Load Response
VINx_INITIAL
VINx
VINx_FINAL
10 us
10 us
Transient Line Stimulus
VINx_INITIAL
VINx_FINAL
Overshoot
VOUT
Undershoot
VOUT Transient Line Response
Figure 20. Transient Waveforms
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
67
Functional Block Requirements and Behaviors
Power Generation
6.4.6.2
Short-circuit Protection
All general purpose LDOs have short-circuit protection capability. The Short-circuit Protection (SCP) system includes debounced
fault condition detection, regulator shutdown, and processor interrupt generation, to contain failures and minimize the chance of
product damage. If a short-circuit condition is detected, the LDO will be disabled by resetting its VGENxEN bit, while at the same
time, an interrupt VGENxFAULTI will be generated to flag the fault to the system processor. The VGENxFAULTI interrupt is
maskable through the VGENxFAULTM mask bit.
The SCP feature is enabled by setting the REGSCPEN bit. If this bit is not set, the regulators will not automatically be disabled
upon a short-circuit detection. However, the current limiter will continue to limit the output current of the regulator. By default, the
REGSCPEN is not set; therefore, at start-up none of the regulators will be disabled if an overloaded condition occurs. A fault
interrupt, VGENxFAULTI, will be generated in an overload condition regardless of the state of the REGSCPEN bit. See Table 75
for SCP behavior configuration.
Table 75. Short-circuit Behavior
6.4.6.3
REGSCPEN[0]
Short-circuit Behavior
0
Current limit
1
Shutdown
LDO Regulator Control
Each LDO is fully controlled through its respective VGENxCTL register. This register enables the user to set the LDO output
voltage according to Table 76 for VGEN1 and VGEN2; and uses the voltage set point on Table 77 for VGEN3 through VGEN6.
Table 76. VGEN1, VGEN2 Output Voltage Configuration
Set Point
VGENx[3:0]
VGENx Output (V)
0
0000
0.800
1
0001
0.850
2
0010
0.900
3
0011
0.950
4
0100
1.000
5
0101
1.050
6
0110
1.100
7
0111
1.150
8
1000
1.200
9
1001
1.250
10
1010
1.300
11
1011
1.350
12
1100
1.400
13
1101
1.450
14
1110
1.500
15
1111
1.550
PF0200Z
68
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 77. VGEN3/ 4/ 5/ 6 Output Voltage Configuration
Set Point
VGENx[3:0]
VGENx Output (V)
0
0000
1.80
1
0001
1.90
2
0010
2.00
3
0011
2.10
4
0100
2.20
5
0101
2.30
6
0110
2.40
7
0111
2.50
8
1000
2.60
9
1001
2.70
10
1010
2.80
11
1011
2.90
12
1100
3.00
13
1101
3.10
14
1110
3.20
15
1111
3.30
Besides the output voltage configuration, the LDOs can be enabled or disabled at anytime during normal mode operation, as well
as programmed to stay “ON” or be disabled when the PMIC enters Standby mode. Each regulator has associated I2C bits for
this. Table 78 presents a summary of all valid combinations of the control bits on VGENxCTL register and the expected behavior
of the LDO output.
Table 78. LDO Control
VGENxEN
VGENxLPWR
VGENxSTBY
STANDBY(50)
VGENxOUT
0
X
X
X
Off
1
0
0
X
On
1
1
0
X
Low Power
1
X
1
0
On
1
0
1
1
Off
1
1
1
1
Low Power
Notes
50. STANDBY refers to a Standby event as described earlier.
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
69
Functional Block Requirements and Behaviors
Power Generation
For more detail information, Table 79 through Table 84 provide a description of all registers necessary to operate all six general
purpose LDO regulators.
Table 79. Register VGEN1CTL - ADDR 0x6C
Name
Bit #
R/W
Default
3:0
R/W
0x80
Sets VGEN1 output voltage.
See Table 76 for all possible configurations.
VGEN1EN
4
–
0x00
Enables or Disables VGEN1 output
0 = OFF
1 = ON
VGEN1STBY
5
R/W
0x00
Set VGEN1 output state when in Standby. Refer
to Table 78.
VGEN1LPWR
6
R/W
0x00
Enable Low Power mode for VGEN1. Refer to
Table 78.
UNUSED
7
–
0x00
UNUSED
VGEN1
Description
Table 80. Register VGEN2CTL - ADDR 0x6D
Name
Bit #
R/W
Default
3:0
R/W
0x80
Sets VGEN2 output voltage.
See Table 76 for all possible configurations.
VGEN2EN
4
–
0x00
Enables or Disables VGEN2 output
0 = OFF
1 = ON
VGEN2STBY
5
R/W
0x00
Set VGEN2 output state when in Standby. Refer
to Table 78.
VGEN2LPWR
6
R/W
0x00
Enable Low Power Mode for VGEN2. Refer to
Table 78.
UNUSED
7
–
0x00
UNUSED
VGEN2
Description
Table 81. Register VGEN3CTL - ADDR 0x6E
Name
Bit #
R/W
Default
3:0
R/W
0x80
Sets VGEN3 output voltage.
See Table 77 for all possible configurations.
VGEN3EN
4
–
0x00
Enables or Disables VGEN3 output
0 = OFF
1 = ON
VGEN3STBY
5
R/W
0x00
Set VGEN3 output state when in Standby. Refer
to Table 78.
VGEN3LPWR
6
R/W
0x00
Enable Low Power mode for VGEN3. Refer to
Table 78.
UNUSED
7
–
0x00
UNUSED
VGEN3
Description
PF0200Z
70
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 82. Register VGEN4CTL - ADDR 0x6F
Name
Bit #
R/W
Default
3:0
R/W
0x80
Sets VGEN4 output voltage.
See Table 77 for all possible configurations.
VGEN4EN
4
–
0x00
Enables or Disables VGEN4 output
0 = OFF
1 = ON
VGEN4STBY
5
R/W
0x00
Set VGEN4 output state when in Standby. Refer
to Table 78.
VGEN4LPWR
6
R/W
0x00
Enable Low Power mode for VGEN4. Refer to
Table 78.
UNUSED
7
–
0x00
UNUSED
VGEN4
Description
Table 83. Register VGEN5CTL - ADDR 0x70
Name
Bit #
R/W
Default
3:0
R/W
0x80
Sets VGEN5 output voltage.
See Table 77 for all possible configurations.
VGEN5EN
4
–
0x00
Enables or Disables VGEN5 output
0 = OFF
1 = ON
VGEN5STBY
5
R/W
0x00
Set VGEN5 output state when in Standby. Refer
to Table 78.
VGEN5LPWR
6
R/W
0x00
Enable Low Power mode for VGEN5. Refer to
Table 78.
UNUSED
7
–
0x00
UNUSED
VGEN5
Description
Table 84. Register VGEN6CTL - ADDR 0x71
Name
Bit #
R/W
Default
3:0
R/W
0x80
Sets VGEN6 output voltage.
See Table 77 for all possible configurations.
VGEN6EN
4
–
0x00
Enables or Disables VGEN6 output
0 = OFF
1 = ON
VGEN6STBY
5
R/W
0x00
Set VGEN6 output state when in Standby. Refer
to Table 78.
VGEN6LPWR
6
R/W
0x00
Enable Low Power mode for VGEN6. Refer to
Table 78.
UNUSED
7
–
0x00
UNUSED
VGEN6
Description
PF0200Z
Analog Integrated Circuit Device Data
Freescale Semiconductor
71
Functional Block Requirements and Behaviors
Power Generation
6.4.6.4
External Components
Table 85 lists the typical component values for the general purpose LDO regulators.
Table 85. LDO External Components
Regulator
Output Capacitor (F)(51)
VGEN1
2.2
VGEN2
4.7
VGEN3
2.2
VGEN4
4.7
VGEN5
2.2
VGEN6
2.2
Notes
51.
6.4.6.5
Use X5R/X7R ceramic capacitors.
LDO Specifications
VGEN1
Table 86. VGEN1 Electrical Characteristics
All parameters are specified at TA = -40 to 85 °C, VIN = 3.6 V, VIN1 = 3.0 V, VGEN1[3:0] = 1111, IGEN1 = 10 mA, typical external
component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, IN1 = 3.0 V, VGEN1[3:0] = 1111,
IGEN1 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
Operating Input Voltage
VIN1
1.75
–
3.40
V
Nominal Output Voltage
VGEN1NOM
–
Table 76
–
V
Operating Load Current
IGEN1
0.0
–
100
mA
Output Voltage Tolerance
1.75 V < VIN1 < 3.4 V
0.0 mA < IGEN1 < 100 mA
VGEN1[3:0] = 0000 to 1111
VGEN1TOL
-3.0
–
3.0
%
Load Regulation
(VGEN1 at IGEN1 = 100 mA) - (VGEN1 at IGEN1 = 0.0 mA)
For any 1.75 V < VIN1 < 3.4 V
VGEN1LOR
–
0.15
–
mV/
mA
Line Regulation
(VGEN1 at VIN1 = 3.4 V) - (VGEN1 at VIN1 = 1.75 V)
For any 0.0 mA < IGEN1 < 100 mA
VGEN1LIR
–
0.30
–
mV/
mA
Current Limit
IGEN1 when VGEN1 is forced to VGEN1NOM/2
IGEN1LIM
122
167
200
mA
Overcurrent Protection Threshold
IGEN1 required to cause the SCP function to disable LDO when
REGSCPEN = 1
IGEN1OCP
115
–
200
mA
IGEN1Q
–
14
–
A
VGEN1
VGEN1 DC
Quiescent Current
No load, Change in IVIN and IVIN1
When VGEN1 enabled
PF0200Z
72
Analog Integrated Circuit Device Data
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 86. VGEN1 Electrical Characteristics (continued)
All parameters are specified at TA = -40 to 85 °C, VIN = 3.6 V, VIN1 = 3.0 V, VGEN1[3:0] = 1111, IGEN1 = 10 mA, typical external
component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, IN1 = 3.0 V, VGEN1[3:0] = 1111,
IGEN1 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
50
37
60
45
–
–
–
–
–
-108
-118
-124
-100
-108
-112
–
–
–
–
12.5
16.5
Unit
VGEN1 AC AND TRANSIENT
PSRR(52)
• IGEN1 = 75 mA, 20 Hz to 20 kHz
VGEN1[3:0] = 0000 - 1101
VGEN1[3:0] = 1110, 1111
PSRRVGEN1
Output Noise Density
VIN1 = 1.75 V, IGEN1 = 75 mA
100 Hz –