Document Number: MPC5534
Rev. 6, Apr 2012
Freescale Semiconductor
Data Sheet: Technical Data
MPC5534
Microcontroller Data Sheet
by: Automotive and Industrial Solutions Gruop
This document provides electrical specifications, pin
assignments, and package diagrams for the MPC5534
microcontroller device. For functional characteristics,
refer to the MPC5534 Microcontroller Reference
Manual.
1
Contents
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . 5
3.3 Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 EMI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 ESD Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 9
3.6 VRC and POR Electrical Specifications . . . . . . . . . 9
3.7 Power-Up/Down Sequencing. . . . . . . . . . . . . . . . . 10
3.8 DC Electrical Specifications . . . . . . . . . . . . . . . . . 14
3.9 Oscillator and FMPLL Electrical Characteristics . . 20
3.10 eQADC Electrical Characteristics . . . . . . . . . . . . . 22
3.11 H7Fb Flash Memory Electrical Characteristics . . . 23
3.12 AC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.13 AC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4
Mechanicals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 MPC5534 208 MAP BGA Pinout . . . . . . . . . . . . . .
4.2 MPC5534 324 PBGA Pinouts . . . . . . . . . . . . . . . .
4.3 MPC5534 208-Pin Package Dimensions. . . . . . . .
4.4 MPC5534 324-Pin Package Dimensions. . . . . . . .
5
Revision History for the MPC5534 Data Sheet . . . . . . . 52
5.1 Changes Between Revisions 5.0 and 6.0 . . . . . . . 52
5.3 Changes Between Revisions 3.0 and 4.0 . . . . . . . 53
Overview
The MPC5534 microcontroller (MCU) is a member of
the MPC5500 family of microcontrollers built on the
Power Architecture embedded technology. This family
of parts has many new features coupled with high
performance CMOS technology to provide substantial
reduction of cost per feature and significant performance
improvement over the MPC500 family.
The host processor core of this device complies with the
Power Architecture embedded category that is 100%
user-mode compatible (including floating point library)
with the original PowerPC instruction set. The embedded
architecture enhancements improve the performance in
embedded applications. The core also has additional
instructions, including digital signal processing (DSP)
instructions, beyond the original PowerPC instruction
set.
© Freescale Semiconductor, Inc., 2008-2012. All rights reserved.
46
46
47
48
50
Overview
The MPC5500 family of parts contains many new features coupled with high performance CMOS
technology to provide significant performance improvement over the MPC565.
The host processor core of the MPC5534 also includes an instruction set enhancement allowing variable
length encoding (VLE). This allows optional encoding of mixed 16- and 32-bit instructions. With this
enhancement, it is possible to significantly reduce the code size footprint.
The MPC5534 has a single-level memory hierarchy consisting of 64-kilobytes (KB) on-chip SRAM and
one megabyte (MB) of internal flash memory. Both the SRAM and the flash memory can hold instructions
and data. The external bus interface (EBI) supports most standard memories used with the MPC5xx family.
The MPC5534 does not support arbitration with other masters on the external bus. The MPC5534 must be
the only master on the external bus, or act as a slave-only device.
The complex input/output timer functions of the MPC5534 are performed by an enhanced time processor
unit (eTPU) engine. The eTPU engine controls 32 hardware channels. The eTPU has been enhanced over
the TPU by providing: 24-bit timers, double-action hardware channels, variable number of parameters per
channel, angle clock hardware, and additional control and arithmetic instructions. The eTPU is
programmed using a high-level programming language.
The less complex timer functions of the MPC5534 are performed by the enhanced modular input/output
system (eMIOS). The eMIOS’ 24 hardware channels are capable of single-action, double-action,
pulse-width modulation (PWM), and modulus-counter operations. Motor control capabilities include
edge-aligned and center-aligned PWM.
Off-chip communication is performed by a suite of serial protocols including controller area networks
(FlexCANs), enhanced deserial/serial peripheral interfaces (DSPIs), and enhanced serial communications
interfaces (eSCIs).
The MCU has an on-chip enhanced queued dual analog-to-digital converter (eQADC) with a 5 V
conversion range. The 324 package has 40-channels; the 208 package has 34 channels.
The system integration unit (SIU) performs several chip-wide configuration functions. Pad configuration
and general-purpose input and output (GPIO) are controlled from the SIU. External interrupts and reset
control are also determined by the SIU. The internal multiplexer sub-block (IMUX) provides multiplexing
of eQADC trigger sources and external interrupt signal multiplexing.
MPC5534 Microcontroller Data Sheet, Rev. 6
2
Freescale Semiconductor
Ordering Information
2
Ordering Information
M PC 5534 M ZQ 80 R
Qualification status
Core code
Device number
Temperature range
Package identifier
Operating frequency (MHz)
Tape and reel status
Temperature Range
M = –40° C to 125° C
Package Identifier
VF = 208MAPBGA SnPb
VM = 208MAPBGA Pb-free
ZQ = 324PBGA SnPb
VZ = 324PBGA Pb-free
Operating Frequency
40 = 40 MHz
66 = 66 MHz
80 = 80 MHz
Tape and Reel Status
R = Tape and reel
(blank) = Trays
Qualification Status
P = Pre qualification
M = Fully spec. qualified, general market flow
S = Fully spec. qualified, automotive flow
Note: Not all options are available on all devices. Refer to Table 1.
Figure 1. MPC5500 Family Part Number Example
Unless noted in this data sheet, all specifications apply from TL to TH.
Table 1. Orderable Part Numbers
Speed (MHz)
Freescale Part Number
Package Description
MPC5534MVZ80
MPC5534MVZ66
MPC5534 324 package
Lead-free (PbFree)
MPC5534MVZ40
MPC5534MVM80
MPC5534MVM66
MPC5534 208 package
Lead-free (PbFree)
MPC5534MVM40
MPC5534MZQ80
MPC5534MZQ66
MPC5534 324 package
Leaded (SnPb)
MPC5534MZQ40
MPC5534MVF80
MPC5534MVF66
MPC5534MVF40
1
2
Operating Temperature 1
MPC5534 208 package
Leaded (SnPb)
Nominal
Max. 2 (fMAX)
80
82
66
68
40
42
80
82
66
68
40
42
80
82
66
68
40
42
80
82
66
68
40
42
Min. (TL)
Max. (TH)
–40° C
125° C
–40° C
125° C
–40° C
125° C
–40° C
125° C
The lowest ambient operating temperature is referenced by TL; the highest ambient operating temperature is referenced by TH.
Speed is the nominal maximum frequency. Max. speed is the maximum speed allowed including frequency modulation (FM).
42 MHz parts allow for 40 MHz system clock + 2% FM; 68 MHz parts allow for 66 MHz system clock + 2% FM, and
82 MHz parts allow for 80 MHz system clock + 2% FM.
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
3
Electrical Characteristics
3
Electrical Characteristics
This section contains detailed information on power considerations, DC/AC electrical characteristics, and
AC timing specifications for the MCU.
3.1
Maximum Ratings
Table 2. Absolute Maximum Ratings 1
Spec
Characteristic
Symbol
Min.
Max.
Unit
1
1.5 V core supply voltage 2
VDD
–0.3
1.7
V
2
Flash program/erase voltage
VPP
–0.3
6.5
V
4
Flash read voltage
VFLASH
–0.3
4.6
V
5
SRAM standby voltage
VSTBY
–0.3
1.7
V
6
Clock synthesizer voltage
VDDSYN
–0.3
4.6
V
7
3.3 V I/O buffer voltage
VDD33
–0.3
4.6
V
8
Voltage regulator control input voltage
VRC33
–0.3
4.6
V
9
Analog supply voltage (reference to VSSA)
VDDA
–0.3
5.5
V
VDDE
–0.3
4.6
V
VDDEH
–0.3
6.5
V
–1.0 5
–1.0 5
6.5 6
4.6 7
V
10
11
12
I/O supply voltage (fast I/O pads)
3
I/O supply voltage (slow and medium I/O pads)
3
4
DC input voltage
VDDEH powered I/O pads
VDDE powered I/O pads
VIN
13
Analog reference high voltage (reference to VRL)
VRH
–0.3
5.5
V
14
VSS to VSSA differential voltage
VSS – VSSA
–0.1
0.1
V
15
VDD to VDDA differential voltage
VDD – VDDA
–VDDA
VDD
V
16
VREF differential voltage
VRH – VRL
–0.3
5.5
V
17
VRH to VDDA differential voltage
VRH – VDDA
–5.5
5.5
V
18
VRL to VSSA differential voltage
VRL – VSSA
–0.3
0.3
V
19
VDDEH to VDDA differential voltage
VDDEH – VDDA
–VDDA
VDDEH
V
20
VDDF to VDD differential voltage
VDDF – VDD
–0.3
0.3
V
21
VRC33 to VDDSYN differential voltage spec has been moved to Table 9 DC Electrical Specifications, Spec 43a.
22
VSSSYN to VSS differential voltage
VSSSYN – VSS
–0.1
0.1
V
23
VRCVSS to VSS differential voltage
VRCVSS – VSS
–0.1
0.1
V
24
Maximum DC digital input current 8
(per pin, applies to all digital pins) 4
IMAXD
–2
2
mA
25
Maximum DC analog input current 9
(per pin, applies to all analog pins)
IMAXA
–3
3
mA
26
Maximum operating temperature range 10
Die junction temperature
TJ
TL
150.0
oC
27
Storage temperature range
TSTG
–55.0
150.0
oC
MPC5534 Microcontroller Data Sheet, Rev. 6
4
Freescale Semiconductor
Electrical Characteristics
Table 2. Absolute Maximum Ratings 1 (continued)
Spec
28
29
Characteristic
Symbol
Min.
Max.
Maximum solder temperature 11
Lead free (Pb-free)
Leaded (SnPb)
TSDR
—
—
260.0
245.0
Moisture sensitivity level 12
MSL
—
3
Unit
o
C
1
Functional operating conditions are given in the DC electrical specifications. Absolute maximum ratings are stress ratings only,
and functional operation at the maxima is not guaranteed. Stress beyond any of the listed maxima can affect device reliability
or cause permanent damage to the device.
2
1.5 V ± 10% for proper operation. This parameter is specified at a maximum junction temperature of 150 oC.
3
All functional non-supply I/O pins are clamped to VSS and VDDE, or VDDEH.
4
AC signal overshoot and undershoot of up to ± 2.0 V of the input voltages is permitted for an accumulative duration of
60 hours over the complete lifetime of the device (injection current not limited for this duration).
5
Internal structures hold the voltage greater than –1.0 V if the injection current limit of 2 mA is met. Keep the negative DC
voltage greater than –0.6 V on SINB during the internal power-on reset (POR) state.
6 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V
DDEH supplies, if the
maximum injection current specification is met (2 mA for all pins) and VDDEH is within the operating voltage specifications.
7 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V
DDE supplies, if the maximum
injection current specification is met (2 mA for all pins) and VDDE is within the operating voltage specifications.
8 Total injection current for all pins (including both digital and analog) must not exceed 25 mA.
9 Total injection current for all analog input pins must not exceed 15 mA.
10 Lifetime operation at these specification limits is not guaranteed.
11 Moisture sensitivity profile per IPC/JEDEC J-STD-020D.
12 Moisture sensitivity per JEDEC test method A112.
3.2
Thermal Characteristics
The shaded rows in the following table indicate information specific to a four-layer board.
Table 3. MPC5534 Thermal Characteristic
Package
Spec
4
5
324
PBGA
Unit
RJA
42
34
°C/W
2
Junction to ambient 1, 3, natural convection (four-layer board 2s2p)
RJA
26
23
°C/W
3
Junction to ambient (@200 ft./min., one-layer board)
RJMA
34
28
°C/W
4
Junction to ambient (@200 ft./min., four-layer board 2s2p)
RJMA
22
20
°C/W
RJB
15
15
°C/W
RJC
8
10
°C/W
JT
2
2
°C/W
7
3
208
MAPBGA
Junction to ambient 1, 2, natural convection (one-layer board)
6
2
Symbol
1
5
1
MPC5534 Thermal Characteristic
4
Junction to board (four-layer board 2s2p)
Junction to case
5
6
Junction to package top , natural convection
Junction temperature is a function of: on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other board components, and board thermal resistance.
Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board in a horizontal position.
Per JEDEC JESD51-6 with the board in a horizontal position.
Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
Indicates the average thermal resistance between the die and the case top surface as measured by the cold plate method
(MIL SPEC-883 Method 1012.1) with the cold plate temperature used for the case temperature.
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
5
Electrical Characteristics
6
The thermal characterization parameter indicates the temperature difference between the package top and the junction
temperature per JEDEC JESD51-2.
3.2.1
General Notes for Specifications at Maximum Junction Temperature
An estimation of the device junction temperature, TJ, can be obtained from the equation:
TJ = TA + (RJA PD)
where:
TA = ambient temperature for the package (oC)
RJA = junction to ambient thermal resistance (oC/W)
PD = power dissipation in the package (W)
The thermal resistance values used are based on the JEDEC JESD51 series of standards to provide
consistent values for estimations and comparisons. The difference between the values determined for the
single-layer (1s) board compared to a four-layer board that has two signal layers, a power and a ground
plane (2s2p), demonstrate that the effective thermal resistance is not a constant. The thermal resistance
depends on the:
• Construction of the application board (number of planes)
• Effective size of the board which cools the component
• Quality of the thermal and electrical connections to the planes
• Power dissipated by adjacent components
Connect all the ground and power balls to the respective planes with one via per ball. Using fewer vias to
connect the package to the planes reduces the thermal performance. Thinner planes also reduce the thermal
performance. When the clearance between the vias leave the planes virtually disconnected, the thermal
performance is also greatly reduced.
As a general rule, the value obtained on a single-layer board is within the normal range for the tightly
packed printed circuit board. The value obtained on a board with the internal planes is usually within the
normal range if the application board has:
• One oz. (35 micron nominal thickness) internal planes
• Components are well separated
• Overall power dissipation on the board is less than 0.02 W/cm2
The thermal performance of any component depends on the power dissipation of the surrounding
components. In addition, the ambient temperature varies widely within the application. For many natural
convection and especially closed box applications, the board temperature at the perimeter (edge) of the
package is approximately the same as the local air temperature near the device. Specifying the local
ambient conditions explicitly as the board temperature provides a more precise description of the local
ambient conditions that determine the temperature of the device.
MPC5534 Microcontroller Data Sheet, Rev. 6
6
Freescale Semiconductor
Electrical Characteristics
At a known board temperature, the junction temperature is estimated using the following equation:
TJ = TB + (RJB PD)
where:
TJ = junction temperature (oC)
TB = board temperature at the package perimeter (oC/W)
RJB = junction-to-board thermal resistance (oC/W) per JESD51-8
PD = power dissipation in the package (W)
When the heat loss from the package case to the air does not factor into the calculation, an acceptable value
for the junction temperature is predictable. Ensure the application board is similar to the thermal test
condition, with the component soldered to a board with internal planes.
The thermal resistance is expressed as the sum of a junction-to-case thermal resistance plus a
case-to-ambient thermal resistance:
RJA = RJC + RCA
where:
RJA = junction-to-ambient thermal resistance (oC/W)
RJC = junction-to-case thermal resistance (oC/W)
RCA = case-to-ambient thermal resistance (oC/W)
RJC is device related and is not affected by other factors. The thermal environment can be controlled to
change the case-to-ambient thermal resistance, RCA. For example, change the air flow around the device,
add a heat sink, change the mounting arrangement on the printed circuit board, or change the thermal
dissipation on the printed circuit board surrounding the device. This description is most useful for
packages with heat sinks where 90% of the heat flow is through the case to heat sink to ambient.
For most packages, a better model is required.
A more accurate two-resistor thermal model can be constructed from the junction-to-board thermal
resistance and the junction-to-case thermal resistance. The junction-to-case thermal resistance describes
when using a heat sink or where a substantial amount of heat is dissipated from the top of the package. The
junction-to-board thermal resistance describes the thermal performance when most of the heat is
conducted to the printed circuit board. This model can be used to generate simple estimations and for
computational fluid dynamics (CFD) thermal models.
To determine the junction temperature of the device in the application on a prototype board, use the
thermal characterization parameter (JT) to determine the junction temperature by measuring the
temperature at the top center of the package case using the following equation:
TJ = TT + (JT PD)
where:
TT = thermocouple temperature on top of the package (oC)
JT = thermal characterization parameter (oC/W)
PD = power dissipation in the package (W)
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
7
Electrical Characteristics
The thermal characterization parameter is measured in compliance with the JESD51-2 specification using
a 40-gauge type T thermocouple epoxied to the top center of the package case. Position the thermocouple
so that the thermocouple junction rests on the package. Place a small amount of epoxy on the thermocouple
junction and approximately 1 mm of wire extending from the junction. Place the thermocouple wire flat
against the package case to avoid measurement errors caused by the cooling effects of the thermocouple
wire.
References:
Semiconductor Equipment and Materials International
3081 Zanker Rd.
San Jose, CA., 95134
(408) 943-6900
MIL-SPEC and EIA/JESD (JEDEC) specifications are available from Global Engineering Documents at
800-854-7179 or 303-397-7956.
JEDEC specifications are available on the web at http://www.jedec.org.
1. C.E. Triplett and B. Joiner, “An Experimental Characterization of a 272 PBGA Within an Automotive
Engine Controller Module,” Proceedings of SemiTherm, San Diego, 1998, pp. 47–54.
2. G. Kromann, S. Shidore, and S. Addison, “Thermal Modeling of a PBGA for Air-Cooled Applications,” Electronic Packaging and Production, pp. 53–58, March 1998.
3. B. Joiner and V. Adams, “Measurement and Simulation of Junction to Board Thermal Resistance and
Its Application in Thermal Modeling,” Proceedings of SemiTherm, San Diego, 1999, pp. 212–220.
3.3
Package
The MPC5534 is available in packaged form. Read the package options in Section 2, “Ordering
Information.” Refer to Section 4, “Mechanicals,” for pinouts and package drawings.
3.4
EMI (Electromagnetic Interference) Characteristics
Table 4. EMI Testing Specifications 1
Spec
Characteristic
Minimum
Typical
Maximum
Unit
0.15
—
1000
MHz
1
Scan range
2
Operating frequency
—
—
fMAX
MHz
3
VDD operating voltages
—
1.5
—
V
4
VDDSYN, VRC33, VDD33, VFLASH, VDDE operating voltages
—
3.3
—
V
5
VPP, VDDEH, VDDA operating voltages
—
5.0
—
V
2
6
Maximum amplitude
—
—
14
32 3
dBuV
7
Operating temperature
—
—
25
oC
1
EMI testing and I/O port waveforms per SAE J1752/3 issued 1995-03. Qualification testing was performed on the MPC5554
and applied to the MPC5500 family as generic EMI performance data.
2 Measured with the single-chip EMI program.
3 Measured with the expanded EMI program.
MPC5534 Microcontroller Data Sheet, Rev. 6
8
Freescale Semiconductor
Electrical Characteristics
3.5
ESD (Electromagnetic Static Discharge) Characteristics
Table 5. ESD Ratings 1, 2
Characteristic
Symbol
Value
Unit
2000
V
R1
1500
C
100
pF
ESD for human body model (HBM)
HBM circuit description
500 (all pins)
ESD for field induced charge model (FDCM)
V
750 (corner pins)
Number of pulses per pin:
Positive pulses (HBM)
Negative pulses (HBM)
—
—
1
1
—
—
Interval of pulses
—
1
second
1
2
All ESD testing conforms to CDF-AEC-Q100 Stress Test Qualification for Automotive Grade Integrated Circuits.
Device failure is defined as: ‘If after exposure to ESD pulses, the device does not meet the device specification requirements,
which includes the complete DC parametric and functional testing at room temperature and hot temperature.
3.6
Voltage Regulator Controller (VRC) and
Power-On Reset (POR) Electrical Specifications
The following table lists the VRC and POR electrical specifications:
Table 6. VRC and POR Electrical Specifications
Spec
1
Characteristic
3.3 V (VDDSYN) POR
3
RESET pin supply
(VDDEH6) POR 1, 2
1
VRC33 voltage
6
Current can be sourced
7
Max.
Units
VPOR15
1.1
1.1
1.35
1.35
V
Asserted (ramp up)
Negated (ramp up)
Asserted (ramp down)
Negated (ramp down)
VPOR33
0.0
2.0
2.0
0.0
0.30
2.85
2.85
0.30
V
Negated (ramp up)
Asserted (ramp down)
VPOR5
2.0
2.0
2.85
2.85
V
VTRANS_START
1.0
2.0
V
When VRC allows the pass
transistor to completely turn on 3, 4
VTRANS_ON
2.0
2.85
V
When the voltage is greater than
the voltage at which the VRC keeps
the 1.5 V supply in regulation 5, 6
VVRC33REG
3.0
—
V
11.0
—
mA
9.0
—
mA
7.5
—
mA
—
1.0
V
Before VRC allows the pass
transistor to start turning on
4
5
Min.
Negated (ramp up)
Asserted (ramp down)
1.5 V (VDD) POR 1
2
Symbol
by VRCCTL at Tj:
–40o C
o
25 C
150o
8
IVRCCTL
7
C
Voltage differential during power up such that:
VDD33 can lag VDDSYN or VDDEH6 before VDDSYN and VDDEH6 reach the
VPOR33 and VPOR5 minimums respectively.
VDD33_LAG
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
9
Electrical Characteristics
Table 6. VRC and POR Electrical Specifications (continued)
Spec
9
10
Characteristic
Absolute value of slew rate on power supply pins
Required gain at Tj:
IDD IVRCCTL (@ fsys = fMAX)
6, 7, 8, 9
Symbol
Min.
Max.
Units
—
—
50
V/ms
35
—
—
40
—
—
50
500
—
o
– 40 C
o
25 C
o
150 C
BETA10
1
The internal POR signals are VPOR15, VPOR33, and VPOR5. On power up, assert RESET before the internal POR negates.
RESET must remain asserted until the power supplies are within the operating conditions as specified in Table 9 DC Electrical
Specifications. On power down, assert RESET before any power supplies fall outside the operating conditions and until the
internal POR asserts.
2
VIL_S (Table 9, Spec15) is guaranteed to scale with VDDEH6 down to VPOR5.
3
Supply full operating current for the 1.5 V supply when the 3.3 V supply reaches this range.
4
It is possible to reach the current limit during ramp up—do not treat this event as short circuit current.
5 At peak current for device.
6 Requires compliance with Freescale’s recommended board requirements and transistor recommendations. Board signal
traces/routing from the VRCCTL package signal to the base of the external pass transistor and between the emitter of the pass
transistor to the VDD package signals must have a maximum of 100 nH inductance and minimal resistance
(less than 1 ). VRCCTL must have a nominal 1 F phase compensation capacitor to ground. VDD must have a 20 F (nominal)
bulk capacitor (greater than 4 F over all conditions, including lifetime). Place high-frequency bypass capacitors consisting of
eight 0.01 F, two 0.1 F, and one 1 F capacitors around the package on the VDD supply signals.
7 I
VRCCTL is measured at the following conditions: VDD = 1.35 V, VRC33 = 3.1 V, VVRCCTL = 2.2 V.
8 Refer to Table 1 for the maximum operating frequency.
9 Values are based on I
DD from high-use applications as explained in the IDD Electrical Specification.
10 BETA represents the worst-case external transistor. It is measured on a per-part basis and calculated as (I
DD IVRCCTL).
3.7
Power-Up/Down Sequencing
Power sequencing between the 1.5 V power supply and VDDSYN or the RESET power supplies is required
if using an external 1.5 V power supply with VRC33 tied to ground (GND). To avoid power-sequencing,
VRC33 must be powered up within the specified operating range, even if the on-chip voltage regulator
controller is not used. Refer to Section 3.7.2, “Power-Up Sequence (VRC33 Grounded),” and
Section 3.7.3, “Power-Down Sequence (VRC33 Grounded).”
Power sequencing requires that VDD33 must reach a certain voltage where the values are read as ones
before the POR signal negates. Refer to Section 3.7.1, “Input Value of Pins During POR Dependent on
VDD33.”
Although power sequencing is not required between VRC33 and VDDSYN during power up, VRC33 must
not lead VDDSYN by more than 600 mV or lag by more than 100 mV for the VRC stage turn-on to operate
within specification. Higher spikes in the emitter current of the pass transistor occur if VRC33 leads or lags
VDDSYN by more than these amounts. The value of that higher spike in current depends on the board power
supply circuitry and the amount of board level capacitance.
Furthermore, when all of the PORs negate, the system clock starts to toggle, adding another large increase
of the current consumed by VRC33. If VRC33 lags VDDSYN by more than 100 mV, the increase in current
consumed can drop VDD low enough to assert the 1.5 V POR again. Oscillations are possible when the
1.5 V POR asserts and stops the system clock, causing the voltage on VDD to rise until the 1.5 V POR
negates again. All oscillations stop when VRC33 is powered sufficiently.
MPC5534 Microcontroller Data Sheet, Rev. 6
10
Freescale Semiconductor
Electrical Characteristics
When powering down, VRC33 and VDDSYN have no delta requirement to each other, because the bypass
capacitors internal and external to the device are already charged. When not powering up or down, no delta
between VRC33 and VDDSYN is required for the VRC to operate within specification.
There are no power up/down sequencing requirements to prevent issues such as latch-up, excessive current
spikes, and so on. Therefore, the state of the I/O pins during power up and power down varies depending
on which supplies are powered.
Table 7 gives the pin state for the sequence cases for all pins with pad type pad_fc (fast type).
Table 7. Pin Status for Fast Pads During the Power Sequence
VDDE
VDD33
VDD
POR
Pin Status for Fast Pad Output Driver
pad_fc (fast)
Low
—
—
Asserted
Low
VDDE
Low
Low
Asserted
High
VDDE
Low
VDD
Asserted
High
VDDE
VDD33
Low
Asserted
High impedance (Hi-Z)
VDDE
VDD33
VDD
Asserted
Hi-Z
VDDE
VDD33
VDD
Negated
Functional
Table 8 gives the pin state for the sequence cases for all pins with pad type pad_mh (medium type) and
pad_sh (slow type).
Table 8. Pin Status for Medium and Slow Pads During the Power Sequence
VDDEH
VDD
POR
Pin Status for Medium and Slow Pad Output Driver
pad_mh (medium) pad_sh (slow)
Low
—
Asserted
Low
VDDEH
Low
Asserted
High impedance (Hi-Z)
VDDEH
VDD
Asserted
Hi-Z
VDDEH
VDD
Negated
Functional
The values in Table 7 and Table 8 do not include the effect of the weak-pull devices on the output pins
during power up.
Before exiting the internal POR state, the pins go to a high-impedance state until POR negates. When the
internal POR negates, the functional state of the signal during reset applies and the weak-pull devices
(up or down) are enabled as defined in the device reference manual. If VDD is too low to correctly
propagate the logic signals, the weak-pull devices can pull the signals to VDDE and VDDEH.
To avoid this condition, minimize the ramp time of the VDD supply to a time period less than the time
required to enable the external circuitry connected to the device outputs.
During initial power ramp-up, when vstby is 0.6v or above. a typical current of 1-3mA and maximum of
4mA may be seen until VDD is applied. This current will not reoccur until Vstby is lowered below Vstby
min specification.
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
11
Electrical Characteristics
Figure 2 shows an approximate interpolation of the ISTBY worst-case specification to estimate values at
different voltages and temperatures. The vertical lines shown at 25 C, 60 C, and 150 C in Figure 2 are
the actual IDD_STBY specifications (27d) listed in Table 9
Figure 2. fISTBY Worst-case Specifications
MPC5534 Microcontroller Data Sheet, Rev. 6
12
Freescale Semiconductor
Electrical Characteristics
3.7.1
Input Value of Pins During POR Dependent on VDD33
When powering up the device, VDD33 must not lag the latest VDDSYN or RESET power pin (VDDEH6) by
more than the VDD33 lag specification listed in Table 6, spec 8. This avoids accidentally selecting the
bypass clock mode because the internal versions of PLLCFG[0:1] and RSTCFG are not powered and
therefore cannot read the default state when POR negates. VDD33 can lag VDDSYN or the RESET power
pin (VDDEH6), but cannot lag both by more than the VDD33 lag specification. This VDD33 lag specification
applies during power up only. VDD33 has no lead or lag requirements when powering down.
3.7.2
Power-Up Sequence (VRC33 Grounded)
The 1.5 V VDD power supply must rise to 1.35 V before the 3.3 V VDDSYN power supply and the RESET
power supply rises above 2.0 V. This ensures that digital logic in the PLL for the 1.5 V power supply does
not begin to operate below the specified operation range lower limit of 1.35 V. Because the internal 1.5 V
POR is disabled, the internal 3.3 V POR or the RESET power POR must hold the device in reset. Since
they can negate as low as 2.0 V, VDD must be within specification before the 3.3 V POR and the RESET
POR negate.
VDDSYN and RESET Power
VDD
2.0 V
1.35 V
VDD must reach 1.35 V before VDDSYN and the RESET power reach 2.0 V
Figure 3. Power-Up Sequence (VRC33 Grounded)
3.7.3
Power-Down Sequence (VRC33 Grounded)
The only requirement for the power-down sequence with VRC33 grounded is if VDD decreases to less than
its operating range, VDDSYN or the RESET power must decrease to less than 2.0 V before the VDD power
increases to its operating range. This ensures that the digital 1.5 V logic, which is reset only by an ORed
POR and can cause the 1.5 V supply to decrease less than its specification value, resets correctly. See
Table 6, footnote 1.
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
13
Electrical Characteristics
3.8
DC Electrical Specifications
Table 9. DC Electrical Specifications (TA = TL to TH)
Spec
1
Characteristic
Core supply voltage (average DC RMS voltage)
1
Symbol
Min
Max.
Unit
VDD
1.35
1.65
V
VDDE
1.62
3.6
V
2
Input/output supply voltage (fast input/output)
3
Input/output supply voltage (slow and medium input/output)
VDDEH
3.0
5.25
V
4
3.3 V input/output buffer voltage
VDD33
3.0
3.6
V
5
Voltage regulator control input voltage
VRC33
3.0
3.6
V
VDDA
4.5
5.25
V
VPP
4.5
5.25
V
2
6
Analog supply voltage
8
Flash programming voltage 3
9
Flash read voltage
VFLASH
3.0
3.6
V
10
SRAM standby voltage 4
VSTBY
0.8
1.2
V
11
Clock synthesizer operating voltage
VDDSYN
3.0
3.6
V
12
Fast I/O input high voltage
VIH_F
0.65 VDDE
VDDE + 0.3
V
13
Fast I/O input low voltage
VIL_F
VSS – 0.3
0.35 VDDE
V
14
Medium and slow I/O input high voltage
VIH_S
0.65 VDDEH
VDDEH + 0.3
V
15
Medium and slow I/O input low voltage
VIL_S
VSS – 0.3
0.35 VDDEH
V
16
Fast input hysteresis
VHYS_F
0.1 VDDE
V
17
Medium and slow I/O input hysteresis
VHYS_S
0.1 VDDEH
V
18
Analog input voltage
VINDC
VSSA – 0.3
VDDA + 0.3
V
19
Fast output high voltage (IOH_F = –2.0 mA)
VOH_F
0.8 VDDE
—
V
20
Slow and medium output high voltage
IOH_S = –2.0 mA
IOH_S = –1.0 mA
VOH_S
0.80 VDDEH
0.85 VDDEH
—
V
21
Fast output low voltage (IOL_F = 2.0 mA)
VOL_F
—
0.2 VDDE
V
22
Slow and medium output low voltage
IOL_S = 2.0 mA
IOL_S = 1.0 mA
VOL_S
—
Load capacitance (fast I/O) 5
DSC (SIU_PCR[8:9]) = 0b00
= 0b01
= 0b10
= 0b11
CL
24
Input capacitance (digital pins)
25
26
23
V
0.20 VDDEH
0.15 VDDEH
—
—
—
—
10
20
30
50
pF
pF
pF
pF
CIN
—
7
pF
Input capacitance (analog pins)
CIN_A
—
10
pF
Input capacitance:
(Shared digital and analog pins AN[12]_MA[0]_SDS,
AN[13]_MA[1]_SDO, AN[14]_MA[2]_SDI, and AN[15]_FCK)
CIN_M
—
12
pF
MPC5534 Microcontroller Data Sheet, Rev. 6
14
Freescale Semiconductor
Electrical Characteristics
Table 9. DC Electrical Specifications (TA = TL to TH) (continued)
Spec
Characteristic
Symbol
Min
Max.
Unit
27a Operating current 1.5 V supplies @ 82 MHz: 6, 7
VDD (including VDDF max current) @1.65 V high use 8, 9, 10, 11, 12
VDD (including VDDF max current) @1.35 V high use 8, 9, 10, 11, 12
IDD
IDD
—
—
250
180
mA
mA
27b Operating current 1.5 V supplies @ 68 MHz: 13, 14
VDD (including VDDF max current) @1.65 V high use15, 16, 17
VDD (including VDDF max current) @1.35 V high use 15, 16, 17
IDD
IDD
—
—
210
160
mA
mA
27c Operating current 1.5 V supplies @ 42 MHz: 13, 14
VDD (including VDDF max current) @1.65 V high use 15, 16, 17
VDD (including VDDF max current) @1.35 V high use 15, 16, 17
IDD
IDD
—
—
130
110
mA
mA
IDD_STBY
IDD_STBY
IDD_STBY
—
—
—
20
30
50
A
A
A
IDD_STBY @ 60o C
VSTBY @ 0.8 V
VSTBY @ 1.0 V
VSTBY @ 1.2 V
IDD_STBY
IDD_STBY
IDD_STBY
—
—
—
70
100
200
A
A
A
IDD_STBY @ 150o C (Tj)
VSTBY @ 0.8 V
VSTBY @ 1.0 V
VSTBY @ 1.2 V
IDD_STBY
IDD_STBY
IDD_STBY
—
—
—
1200
1500
2000
A
A
A
VDD33 19
IDD_33
—
2 + (values
derived from
procedure of
footnote 19)
mA
VFLASH
IVFLASH
—
10
mA
VDDSYN
IDDSYN
—
15
mA
Operating current 5.0 V supplies (12 MHz ADCLK):
VDDA (VDDA0 + VDDA1)
Analog reference supply current (VRH, VRL)
VPP
IDD_A
IREF
IPP
—
—
—
20.0
1.0
25.0
mA
mA
mA
Operating current VDDE supplies: 20
VDDEH1
VDDE2
VDDE3
VDDEH4
VDDE5
VDDEH6
VDDE7
VDDEH8
VDDEH9
IDD1
IDD2
IDD3
IDD4
IDD5
IDD6
IDD7
IDD8
IDD9
—
—
—
—
—
—
—
—
—
Refer to
footnote 20
mA
mA
mA
mA
mA
mA
mA
mA
mA
27d Refer to Figure 2 for an interpolation of this data.18
IDD_STBY @ 25o C
VSTBY @ 0.8 V
VSTBY @ 1.0 V
VSTBY @ 1.2 V
28
29
30
Operating current 3.3 V supplies @ fMAX MHz
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
15
Electrical Characteristics
Table 9. DC Electrical Specifications (TA = TL to TH) (continued)
Spec
31
Characteristic
Min
Max.
Unit
10
20
20
110
130
170
A
A
A
10
20
20
100
130
170
A
A
A
IACT_S
10
20
150
170
A
A
IINACT_D
–2.5
2.5
A
IIC
–2.0
2.0
mA
IINACT_A
–150
150
nA
IINACT_AD
–2.5
2.5
A
VSS – VSSA
–100
100
mV
VRL
VSSA – 0.1
VSSA + 0.1
V
VRL – VSSA
–100
100
mV
VRH
VDDA – 0.1
VDDA + 0.1
V
VRH – VRL
4.5
5.25
V
Fast I/O weak pullup current 21
1.62–1.98 V
2.25–2.75 V
3.00–3.60 V
IACT_F
Fast I/O weak pulldown current 21
1.62–1.98 V
2.25–2.75 V
3.00–3.60 V
32
Symbol
Slow and medium I/O weak pullup/down current 21
3.0–3.6 V
4.5–5.5 V
33
I/O input leakage current 22
34
DC injection current (per pin)
35
Analog input current, channel off 23
35a Analog input current, shared analog / digital pins
(AN[12], AN[13], AN[14], AN[15])
36
VSS to VSSA differential voltage 24
37
Analog reference low voltage
38
VRL differential voltage
39
Analog reference high voltage
40
VREF differential voltage
41
VSSSYN to VSS differential voltage
VSSSYN – VSS
–50
50
mV
42
VRCVSS to VSS differential voltage
VRCVSS – VSS
–50
50
mV
43
VDDF to VDD differential voltage
VDDF – VDD
–100
100
mV
43a VRC33 to VDDSYN differential voltage
VRC33 – VDDSYN
–0.1
0.1 25
V
VIDIFF
–2.5
2.5
V
TA = (TL to TH)
TL
TH
C
—
—
50
V/ms
44
Analog input differential signal range (with common mode 2.5 V)
45
Operating temperature range, ambient (packaged)
46
Slew rate on power-supply pins
1
VDDE2 and VDDE3 are limited to 2.25–3.6 V only if SIU_ECCR[EBTS] = 0; VDDE2 and VDDE3 have a range of 1.6–3.6 V if
SIU_ECCR[EBTS] = 1.
2 |V
DDA0 – VDDA1 | must be < 0.1 V.
3
VPP can drop to 3.0 V during read operations.
4
If standby operation is not required, connect VSTBY to ground.
5 Applies to CLKOUT, external bus pins, and Nexus pins.
6
Maximum average RMS DC current.
7
Figure 2 shows an illustration of the IDD_STBY values interpolated for these temperature values.
8 Average current measured on Automotive benchmark.
9 Peak currents can be higher on specialized code.
10
High use current measured while running optimized SPE assembly code with all channels of the eMIOS and eTPU running
autonomously, plus the eDMA transferring data continuously from SRAM to SRAM.
MPC5534 Microcontroller Data Sheet, Rev. 6
16
Freescale Semiconductor
Electrical Characteristics
11
Power requirements for the VDD33 supply depend on the frequency of operation, load of all I/O pins, and the voltages on the I/O
segments. Refer to Table 11 for values to calculate power dissipation for specific operation.
12
Power requirements for each I/O segment are dependent on the frequency of operation and load of the I/O pins on a particular I/O
segment, and the voltage of the I/O segment. Refer to Table 10 for values to calculate power dissipation for specific operation. The
total power consumption of an I/O segment is the sum of the individual power consumptions for each pin on the segment.
13
Maximum average RMS DC current.
14
Figure 2 shows an illustration of the IDD_STBY values interpolated for these temperature values.
15
Average current measured on automotive benchmark.
16
Peak currents can be higher on specialized code.
17
High use current measured while running optimized SPE assembly code with all channels of the eMIOS and eTPU running
autonomously, plus the eDMA transferring data continuously from SRAM to SRAM.
18
Figure 2 shows that the current specification relates to average standby operation after SRAM has been loaded with data. For power
up current see Section 3.7, “Power-Up/Down Sequencing.
19
Power requirements for the VDD33 supply depend on the frequency of operation, load of all I/O pins, and the voltages on the I/O
segments. Refer to Table 11 for values to calculate the power dissipation for a specific operation.
20
Power requirements for each I/O segment are dependent on the frequency of operation and load of the I/O pins on a particular I/O
segment, and the voltage of the I/O segment. Refer to Table 10 for values to calculate power dissipation for specific operation. The
total power consumption of an I/O segment is the sum of the individual power consumptions for each pin on the segment.
21 Absolute value of current, measured at V and V .
IL
IH
22 Weak pullup/down inactive. Measured at V
DDE = 3.6 V and VDDEH = 5.25 V. Applies to pad types: pad_fc, pad_sh, and pad_mh.
23 Maximum leakage occurs at maximum operating temperature. Leakage current decreases by approximately one-half for each 8 oC
to 12 oC, in the ambient temperature range of 50 oC to 125 oC. Applies to pad types: pad_a and pad_ae.
24 V
SSA refers to both VSSA0 and VSSA1. | VSSA0 – VSSA1 | must be < 0.1 V.
25 Up to 0.6 V during power up and power down.
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
17
Electrical Characteristics
3.8.1
I/O Pad Current Specifications
The power consumption of an I/O segment depends on the usage of the pins on a particular segment. The
power consumption is the sum of all output pin currents for a segment. The output pin current can be
calculated from Table 10 based on the voltage, frequency, and load on the pin. Use linear scaling to
calculate pin currents for voltage, frequency, and load parameters that fall outside the values given in
Table 10.
Table 10. I/O Pad Average DC Current (TA = TL to TH)1
Frequency
(MHz)
Load2 (pF)
Voltage (V)
Drive Select /
Slew Rate
Control Setting
Current (mA)
25
50
5.25
11
8.0
10
50
5.25
01
3.2
2
50
5.25
00
0.7
4
2
200
5.25
00
2.4
5
50
50
5.25
11
17.3
Spec
Pad Type
Symbol
1
2
3
6
Slow
IDRV_SH
20
50
5.25
01
6.5
3.33
50
5.25
00
1.1
8
3.33
200
5.25
00
3.9
9
66
10
3.6
00
2.8
10
66
20
3.6
01
5.2
11
66
30
3.6
10
8.5
7
Medium
IDRV_MH
12
66
50
3.6
11
11.0
13
66
10
1.98
00
1.6
14
66
20
1.98
01
2.9
15
66
30
1.98
10
4.2
16
66
50
1.98
11
6.7
17
56
10
3.6
00
2.4
18
56
20
3.6
01
4.4
19
56
30
3.6
10
7.2
20
56
50
3.6
11
9.3
56
10
1.98
00
1.3
22
56
20
1.98
01
2.5
23
56
30
1.98
10
3.5
24
56
50
1.98
11
5.7
25
40
10
3.6
00
1.7
26
40
20
3.6
01
3.1
27
40
30
3.6
10
5.1
21
Fast
IDRV_FC
28
40
50
3.6
11
6.6
29
40
10
1.98
00
1.0
30
40
20
1.98
01
1.8
31
40
30
1.98
10
2.5
32
40
50
1.98
11
4.0
1
These values are estimates from simulation and are not tested. Currents apply to output pins only.
2
All loads are lumped.
MPC5534 Microcontroller Data Sheet, Rev. 6
18
Freescale Semiconductor
Electrical Characteristics
3.8.2
I/O Pad VDD33 Current Specifications
The power consumption of the VDD33 supply dependents on the usage of the pins on all I/O segments. The
power consumption is the sum of all input and output pin VDD33 currents for all I/O segments. The output
pin VDD33 current can be calculated from Table 11 based on the voltage, frequency, and load on all fast
(pad_fc) pins. The input pin VDD33 current can be calculated from Table 11 based on the voltage,
frequency, and load on all pad_sh and pad_mh pins. Use linear scaling to calculate pin currents for voltage,
frequency, and load parameters that fall outside the values given in Table 11.
Table 11. VDD33 Pad Average DC Current (TA = TL to TH) 1
Spec
Pad Type
Symbol
Frequency
(MHz)
Load 2
(pF)
VDD33
(V)
VDDE
(V)
Drive
Select
Current
(mA)
Inputs
1
Slow
I33_SH
66
0.5
3.6
5.5
NA
0.003
2
Medium
I33_MH
66
0.5
3.6
5.5
NA
0.003
3
66
10
3.6
3.6
00
0.35
4
66
20
3.6
3.6
01
0.53
5
66
30
3.6
3.6
10
0.62
6
66
50
3.6
3.6
11
0.79
7
66
10
3.6
1.98
00
0.35
8
66
20
3.6
1.98
01
0.44
9
66
30
3.6
1.98
10
0.53
10
66
50
3.6
1.98
11
0.70
11
56
10
3.6
3.6
00
0.30
12
56
20
3.6
3.6
01
0.45
13
56
30
3.6
3.6
10
0.52
Outputs
14
56
50
3.6
3.6
11
0.67
56
10
3.6
1.98
00
0.30
16
56
20
3.6
1.98
01
0.37
17
56
30
3.6
1.98
10
0.45
18
56
50
3.6
1.98
11
0.60
19
40
10
3.6
3.6
00
0.21
20
40
20
3.6
3.6
01
0.31
21
40
30
3.6
3.6
10
0.37
15
Fast
I33_FC
22
40
50
3.6
3.6
11
0.48
23
40
10
3.6
1.98
00
0.21
24
40
20
3.6
1.98
01
0.27
25
40
30
3.6
1.98
10
0.32
26
40
50
3.6
1.98
11
0.42
1
These values are estimated from simulation and not tested. Currents apply to output pins for the fast pads only and to input
pins for the slow and medium pads only.
2
All loads are lumped.
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
19
Electrical Characteristics
3.9
Oscillator and FMPLL Electrical Characteristics
Table 12. FMPLL Electrical Specifications
(VDDSYN = 3.0–3.6 V; VSS = VSSSYN = 0.0 V; TA = TL to TH)
Spec
Characteristic
Symbol
Minimum
Maximum
1
PLL reference frequency range: 1
Crystal reference
External reference
Dual controller (1:1 mode)
fref_crystal
fref_ext
fref_1:1
8
8
24
20
20
fsys 2
2
System frequency 2
fsys
fICO(MIN) 2RFD
fMAX 3
MHz
3
System clock period
tCYC
—
1 fsys
ns
4
Loss of reference frequency 4
fLOR
100
1000
kHz
5
Self-clocked mode (SCM) frequency 5
fSCM
7.4
17.5
MHz
EXTAL input high voltage crystal mode 6
VIHEXT
VXTAL + 0.4 V
—
V
All other modes
[dual controller (1:1), bypass, external reference]
VIHEXT
(VDDE5 2) + 0.4 V
—
V
EXTAL input low voltage crystal mode 7
VILEXT
—
VXTAL – 0.4 V
V
All other modes
[dual controller (1:1), bypass, external reference]
VILEXT
—
(VDDE5 2) – 0.4 V
V
IXTAL
0.8
3
mA
6
7
Unit
MHz
8
XTAL current 8
9
Total on-chip stray capacitance on XTAL
CS_XTAL
—
1.5
pF
10
Total on-chip stray capacitance on EXTAL
CS_EXTAL
—
1.5
pF
11
Crystal manufacturer’s recommended capacitive
load
CL
Refer to crystal
specification
Refer to crystal
specification
pF
Discrete load capacitance to connect to EXTAL
CL_EXTAL
—
(2 CL) – CS_EXTAL
– CPCB_EXTAL 9
pF
Discrete load capacitance to connect to XTAL
CL_XTAL
—
(2 CL) – CS_XTAL
– CPCB_XTAL 9
pF
tlpll
—
750
s
tskew
–2
2
ns
12
13
14
PLL lock time 10
15
Dual controller (1:1) clock skew
(between CLKOUT and EXTAL) 11, 12
16
Duty cycle of reference
tDC
40
60
%
17
Frequency unLOCK range
fUL
–4.0
4.0
% fSYS
18
Frequency LOCK range
fLCK
–2.0
2.0
% fSYS
MPC5534 Microcontroller Data Sheet, Rev. 6
20
Freescale Semiconductor
Electrical Characteristics
Table 12. FMPLL Electrical Specifications (continued)
(VDDSYN = 3.0–3.6 V; VSS = VSSSYN = 0.0 V; TA = TL to TH)
Spec
Characteristic
Symbol
Minimum
Maximum
CJITTER
19
CLKOUT period jitter, measured at fSYS max: 13, 14
Peak-to-peak jitter (clock edge to clock edge)
Long term jitter (averaged over a 2 ms interval)
20
Frequency modulation range limit 15
(do not exceed fsys maximum)
21
ICO frequency
fico = [ fref_crystal (MFD + 4) ] (PREDIV + 1) 16
fico = [ fref_ext (MFD + 4) ] (PREDIV + 1)
22
Predivider output frequency (to PLL)
Unit
—
—
5.0
0.01
CMOD
0.8
2.4
%fSYS
fico
48
8017
MHz
fPREDIV
4
20 18
MHz
%
fCLKOUT
1
Nominal crystal and external reference values are worst-case not more than 1%. The device operates correctly if the frequency
remains within ± 5% of the specification limit. This tolerance range allows for a slight frequency drift of the crystals over time.
The designer must thoroughly understand the drift margin of the source clock.
2 All internal registers retain data at 0 Hz.
3 Up to the maximum frequency rating of the device (refer to Table 1).
4 Loss of reference frequency is defined as the reference frequency detected internally, which transitions the PLL into self-clocked
mode.
5 The PLL operates at self-clocked mode (SCM) frequency when the reference frequency falls below f
LOR. SCM frequency is
measured on the CLKOUT ball with the divider set to divide-by-two of the system clock.
NOTE: In SCM, the MFD and PREDIV have no effect and the RFD is bypassed.
6 Use the EXTAL input high voltage parameter when using the FlexCAN oscillator in crystal mode (no quartz crystals or
resonators). (Vextal – Vxtal) must be 400 mV for the oscillator’s comparator to produce the output clock.
7 Use the EXTAL input low voltage parameter when using the FlexCAN oscillator in crystal mode (no quartz crystals or
resonators). (Vxtal – Vextal) must be 400 mV for the oscillator’s comparator to produce the output clock.
8 I
xtal is the oscillator bias current out of the XTAL pin with both EXTAL and XTAL pins grounded.
9 C
PCB_EXTAL and CPCB_XTAL are the measured PCB stray capacitances on EXTAL and XTAL, respectively.
10 This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the
synthesizer control register (SYNCR). From power up with crystal oscillator reference, the lock time also includes the crystal
startup time.
11 PLL is operating in 1:1 PLL mode.
12 V
DDE = 3.0–3.6 V.
13 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f .
sys
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the PLL circuitry via VDDSYN and VSSSYN and variation in crystal oscillator frequency increase the jitter percentage
for a given interval. CLKOUT divider is set to divide-by-two.
14 Values are with frequency modulation disabled. If frequency modulation is enabled, jitter is the sum of (jitter + Cmod).
15 Modulation depth selected must not result in f
sys value greater than the fsys maximum specified value.
RFD).
sys = fico (2
16 f
17
The ICO frequency can be higher than the maximum allowable system frequency. For this case, set the FMPLL synthesizer
control register reduced frequency divider (FMPLL_SYNCR[RFD]) to divide-by-two (RFD = 0b001). Therefore, for a 40 MHz
maximum device (system frequency), program the FMPLL to generate 80 MHz at the ICO output and then divide-by-two the
RFD to provide the 40 MHz clock.
18 Maximum value for dual controller (1:1) mode is (f
MAX 2) with the predivider set to 1 (FMPLL_SYNCR[PREDIV] = 0b001).
MPC5534 Microcontroller Data Sheet, Rev. 6
Freescale Semiconductor
21
Electrical Characteristics
3.10
eQADC Electrical Characteristics
Table 13. eQADC Conversion Specifications (TA = TL to TH)
Spec
Characteristic
Symbol
Minimum
Maximum
Unit
FADCLK
1
12
MHz
13 + 2 (15)
14 + 2 (16)
13 + 128 (141)
14 + 128 (142)
1
ADC clock (ADCLK) frequency 1
Conversion cycles
Differential
Single ended
CC
2
3
Stop mode recovery time 2
TSR
10
—
s
—
1.25
—
mV
3
ADCLK
cycles
4
Resolution
5
INL: 6 MHz ADC clock
INL6
–4
4
Counts 3
6
INL: 12 MHz ADC clock
INL12
–8
7
8
9
10
DNL: 6 MHz ADC clock
DNL: 12 MHz ADC clock
Offset error with calibration
Full-scale gain error with calibration
7, 8, 9, 10
8
Counts
DNL6
–3
4
34
Counts
DNL12
–6 4
6
4
Counts
OFFWC
–4 5
4
5
Counts
GAINWC
–8 6
8
6
Counts
IINJ
–1
1
mA
11
Disruptive input injection current
12
Incremental error due to injection current. All channels are
10 k < Rs
工商网监
湘ICP备2023018690号
