MPC8540CPX667JC

Freescale Semiconductor MPC8540EC Rev. 4.1, 07/2007 Technical Data MPC8540 Integrated Processor Hardware Specifications The MPC8540 integrates a PowerPC™ processor core built on Power Architecture™ technology with system logic required for networking, telecommunications, and wireless infrastructure applications. The MPC8540 is a member of the PowerQUICC™ III family of devices that combine system-level support for industry-standard interfaces with processors that implement the embedded category of the Power Architecture technology. For functional characteristics of the processor, refer to the MPC8540 PowerQUICC III Integrated Host Processor Reference Manual. To locate any published errata or updates for this document, contact your Freescale sales office. © Freescale Semiconductor, Inc., 2004-2007. All rights reserved. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . 7 Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 12 Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . 15 DDR SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ethernet: Three-Speed,10/100, MII Management . . 22 Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 PCI/PCI-X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 RapidIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Package and Pin Listings . . . . . . . . . . . . . . . . . . . . . 66 Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 System Design Information . . . . . . . . . . . . . . . . . . . 88 Document Revision History . . . . . . . . . . . . . . . . . . . 95 Device Nomenclature . . . . . . . . . . . . . . . . . . . . . . . 100 Overview 1 Overview The following section provides a high-level overview of the MPC8540 features. Figure 1 shows the major functional units within the MPC8540. DDR SDRAM ROM, SDRAM, GPIO 256KB L2-Cache/ SRAM DDR SDRAM Controller Local Bus Controller e500 Coherency Module 32 KB L1 I Cache Programmable Interrupt Controller IRQs e500 Core Core Complex Bus RapidIO Controller RapidIO-8 16 Gb/s PCI/PCI-X Controller PCI-X 64b 133 MHz OCeaN 10/100 ENET MII 32 KB L1 D Cache 4ch DMA Controller Serial DUART TSEC 10/100/1G I2C I2 C MII, GMII,TBI, RTBI, RGMII Controller TSEC 10/100/1G MII, GMII,TBI, RTBI, RGMII Figure 1. MPC8540 Block Diagram 1.1 Key Features The following lists an overview of the MPC8540 feature set. • High-performance, 32-bit Book E–enhanced core that implements the Power Architecture — 32-Kbyte L1 instruction cache and 32-Kbyte L1 data cache with parity protection. Caches can be locked entirely or on a per-line basis. Separate locking for instructions and data — Memory management unit (MMU) especially designed for embedded applications — Enhanced hardware and software debug support — Performance monitor facility (similar to but different from the MPC8540 performance monitor described in Chapter 18, “Performance Monitor.” MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 2 Freescale Semiconductor Overview • • • 256 Kbyte L2 cache/SRAM — Can be configured as follows – Full cache mode (256-Kbyte cache). – Full memory-mapped SRAM mode (256-Kbyte SRAM mapped as a single 256-Kbyte block or two 128-Kbyte blocks) – Half SRAM and half cache mode (128-Kbyte cache and 128-Kbyte memory-mapped SRAM) — Full ECC support on 64-bit boundary in both cache and SRAM modes — Cache mode supports instruction caching, data caching, or both — External masters can force data to be allocated into the cache through programmed memory ranges or special transaction types (stashing) — Eight-way set-associative cache organization (1024 sets of 32-byte cache lines) — Supports locking the entire cache or selected lines. Individual line locks are set and cleared through Book E instructions or by externally mastered transactions — Global locking and flash clearing done through writes to L2 configuration registers — Instruction and data locks can be flash cleared separately — Read and write buffering for internal bus accesses — SRAM features include the following: – I/O devices access SRAM regions by marking transactions as snoopable (global) – Regions can reside at any aligned location in the memory map – Byte accessible ECC is protected using read-modify-write transactions accesses for smaller than cache-line accesses. Address translation and mapping unit (ATMU) — Eight local access windows define mapping within local 32-bit address space — Inbound and outbound ATMUs map to larger external address spaces – Three inbound windows plus a configuration window on PCI/PCI-X – Four inbound windows plus a default and configuration window on RapidIO – Four outbound windows plus default translation for PCI – Eight outbound windows plus default translation for RapidIO DDR memory controller — Programmable timing supporting DDR-1 SDRAM — 64-bit data interface, up to 333-MHz data rate — Four banks of memory supported, each up to 1 Gbyte — DRAM chip configurations from 64 Mbits to 1 Gbit with x8/x16 data ports — Full ECC support — Page mode support (up to 16 simultaneous open pages) — Contiguous or discontiguous memory mapping MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 3 Overview • • • — Read-modify-write support for RapidIO atomic increment, decrement, set, and clear transactions — Sleep mode support for self refresh SDRAM — Supports auto refreshing — On-the-fly power management using CKE signal — Registered DIMM support — Fast memory access via JTAG port — 2.5-V SSTL2 compatible I/O RapidIO interface unit — 8-bit RapidIO I/O and messaging protocols — Source-synchronous double data rate (DDR) interfaces — Supports small type systems (small domain, 8-bit device ID) — Supports four priority levels (ordering within a level) — Reordering across priority levels — Maximum data payload of 256 bytes per packet — Packet pacing support at the physical layer — CRC protection for packets — Supports atomic operations increment, decrement, set, and clear — LVDS signaling RapidIO–compliant message unit — One inbound data message structure (inbox) — One outbound data message structure (outbox) — Supports chaining and direct modes in the outbox — Support of up to 16 packets per message — Support of up to 256 bytes per packet and up to 4 Kbytes of data per message — Supports one inbound doorbell message structure Programmable interrupt controller (PIC) — Programming model is compliant with the OpenPIC architecture — Supports 16 programmable interrupt and processor task priority levels — Supports 12 discrete external interrupts — Supports 4 message interrupts with 32-bit messages — Supports connection of an external interrupt controller such as the 8259 programmable interrupt controller — Four global high resolution timers/counters that can generate interrupts — Supports 22 other internal interrupt sources — Supports fully nested interrupt delivery — Interrupts can be routed to external pin for external processing MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 4 Freescale Semiconductor Overview • • • • • • — Interrupts can be routed to the e500 core’s standard or critical interrupt inputs — Interrupt summary registers allow fast identification of interrupt source I2C controller — Two-wire interface — Multiple master support — Master or slave I2C mode support — On-chip digital filtering rejects spikes on the bus Boot sequencer — Optionally loads configuration data from serial ROM at reset via the I2C interface — Can be used to initialize configuration registers and/or memory — Supports extended I2C addressing mode — Data integrity checked with preamble signature and CRC DUART — Two 4-wire interfaces (SIN, SOUT, RTS, CTS) — Programming model compatible with the original 16450 UART and the PC16550D 10/100 fast Ethernet controller (FEC) — Operates at 10 to 100 megabits per second (Mbps) as a device debug and maintenance port Local bus controller (LBC) — Multiplexed 32-bit address and data operating at up to 166 MHz — Eight chip selects support eight external slaves — Up to eight-beat burst transfers — The 32-, 16-, and 8-bit port sizes are controlled by an on-chip memory controller — Three protocol engines available on a per chip select basis: – General purpose chip select machine (GPCM) – Three user programmable machines (UPMs) – Dedicated single data rate SDRAM controller — Parity support — Default boot ROM chip select with configurable bus width (8-,16-, or 32-bit) Two three-speed (10/100/1Gb) Ethernet controllers (TSECs) — Dual IEEE 802.3, 802.3u, 802.3x, 802.3z, 802.3ac, 802.3ab compliant controllers — Support for different Ethernet physical interfaces: – 10/100/1Gb Mbps IEEE 802.3 GMII – 10/100 Mbps IEEE 802.3 MII – 10 Mbps IEEE 802.3 MII – 1000 Mbps IEEE 802.3z TBI – 10/100/1Gb Mbps RGMII/RTBI — Full- and half-duplex support MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 5 Overview • • • — Buffer descriptors are backward compatible with MPC8260 and MPC860T 10/100 programming models — 9.6-Kbyte jumbo frame support — RMON statistics support — 2-Kbyte internal transmit and receive FIFOs — MII management interface for control and status — Programmable CRC generation and checking — Ability to force allocation of header information and buffer descriptors into L2 cache. OCeaN switch fabric — Four-port crossbar packet switch — Reorders packets from a source based on priorities — Reorders packets to bypass blocked packets — Implements starvation avoidance algorithms — Supports packets with payloads of up to 256 bytes Integrated DMA controller — Four-channel controller — All channels accessible by both the local and remote masters — Extended DMA functions (advanced chaining and striding capability) — Support for scatter and gather transfers — Misaligned transfer capability — Interrupt on completed segment, link, list, and error — Supports transfers to or from any local memory or I/O port — Selectable hardware-enforced coherency (snoop/no-snoop) — Ability to start and flow control each DMA channel from external 3-pin interface — Ability to launch DMA from single write transaction PCI/PCI-X controller — PCI 2.2 and PCI-X 1.0 compatible — 64- or 32-bit PCI port supports at 16 to 66 MHz — 64-bit PCI-X support up to 133 MHz — Host and agent mode support — 64-bit dual address cycle (DAC) support — PCI-X supports multiple split transactions — Supports PCI-to-memory and memory-to-PCI streaming — Memory prefetching of PCI read accesses — Supports posting of processor-to-PCI and PCI-to-memory writes — PCI 3.3-V compatible — Selectable hardware-enforced coherency MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 6 Freescale Semiconductor Electrical Characteristics • • • • • Power management — Fully static 1.2-V CMOS design with 3.3- and 2.5-V I/O — Supports power saving modes: doze, nap, and sleep — Employs dynamic power management, which automatically minimizes power consumption of blocks when they are idle. System performance monitor — Supports eight 32-bit counters that count the occurrence of selected events — Ability to count up to 512 counter-specific events — Supports 64 reference events that can be counted on any of the 8 counters — Supports duration and quantity threshold counting — Burstiness feature that permits counting of burst events with a programmable time between bursts — Triggering and chaining capability — Ability to generate an interrupt on overflow System access port — Uses JTAG interface and a TAP controller to access entire system memory map — Supports 32-bit accesses to configuration registers — Supports cache-line burst accesses to main memory — Supports large block (4-Kbyte) uploads and downloads — Supports continuous bit streaming of entire block for fast upload and download IEEE 1149.1-compliant, JTAG boundary scan 783 FC-PBGA package 2 Electrical Characteristics This section provides the electrical specifications and thermal characteristics for the MPC8540. The MPC8540 is currently targeted to these specifications. Some of these specifications are independent of the I/O cell, but are included for a more complete reference. These are not purely I/O buffer design specifications. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 7 Electrical Characteristics 2.1 Overall DC Electrical Characteristics This section covers the ratings, conditions, and other characteristics. 2.1.1 Absolute Maximum Ratings Table 1 provides the absolute maximum ratings. Table 1. Absolute Maximum Ratings 1 Characteristic Core supply voltage Symbol Max Value Unit V VDD –0.3 to 1.32 –0.3 to 1.43 For devices rated at 667 and 833 MHz For devices rated at 1 GHz PLL supply voltage Notes V AVDD –0.3 to 1.32 –0.3 to 1.43 For devices rated at 667 and 833 MHz For devices rated at 1 GHz DDR DRAM I/O voltage GVDD –0.3 to 3.63 V Three-speed Ethernet I/O voltage LVDD –0.3 to 3.63 –0.3 to 2.75 V PCI/PCI-X, local bus, RapidIO, 10/100 Ethernet, MII management, DUART, system control and power management, I2C, and JTAG I/O voltage OVDD –0.3 to 3.63 V 3 Input voltage MVIN –0.3 to (GVDD + 0.3) V 2, 5 MVREF –0.3 to (GVDD + 0.3) V 2, 5 Three-speed Ethernet signals LVIN –0.3 to (LVDD + 0.3) V 4, 5 Local bus, RapidIO, 10/100 Ethernet, DUART, SYSCLK, system control and power management, I2C, and JTAG signals OVIN –0.3 to (OVDD + 0.3) V 5 PCI/PCI-X OVIN –0.3 to (OVDD + 0.3) V 6 TSTG –55 to 150 •C DDR DRAM signals DDR DRAM reference Storage temperature range Notes: 1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause permanent damage to the device. 2. Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 3. Caution: OVIN must not exceed OVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 4. Caution: LVIN must not exceed LVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 5. (M,L,O)VIN and MVREF may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2. 6. OVIN on the PCI interface may overshoot/undershoot according to the PCI Electrical Specification for 3.3-V operation, as shown in Figure 3. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 8 Freescale Semiconductor Electrical Characteristics 2.1.2 Power Sequencing The MPC8540 requires its power rails to be applied in a specific sequence in order to ensure proper device operation. These requirements are as follows for power up: 1. VDD, AVDD 2. GVDD, LVDD, OVDD (I/O supplies) Items on the same line have no ordering requirement with respect to one another. Items on separate lines must be ordered sequentially such that voltage rails on a previous step must reach 90 percent of their value before the voltage rails on the current step reach 10 percent of theirs. NOTE If the items on line 2 must precede items on line 1, please ensure that the delay will not exceed 500 ms and the power sequence is not done greater than once per day in production environment. NOTE From a system standpoint, if the I/O power supplies ramp prior to the VDD core supply, the I/Os on the MPC8540 may drive a logic one or zero during power-up. 2.1.3 Recommended Operating Conditions Table 2 provides the recommended operating conditions for the MPC8540. Note that the values in Table 2 are the recommended and tested operating conditions. Proper device operation outside of these conditions is not guaranteed. Table 2. Recommended Operating Conditions Characteristic Core supply voltage Symbol Recommended Value V VDD 1.2 V ± 60 mV 1.3 V ± 50 mV For devices rated at 667 and 833 MHz For devices rated at 1 GHz PLL supply voltage Unit AVDD V 1.2 V ± 60 mV 1.3 V ± 50 mV For devices rated at 667 and 833 MHz For devices rated at 1 GHz DDR DRAM I/O voltage GVDD 2.5 V ± 125 mV V Three-speed Ethernet I/O voltage LVDD 3.3 V ± 165 mV 2.5 V ± 125 mV V PCI/PCI-X, local bus, RapidIO, 10/100 Ethernet, MII management, DUART, system control and power management, I2C, and JTAG I/O voltage OVDD 3.3 V ± 165 mV V MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 9 Electrical Characteristics Table 2. Recommended Operating Conditions (continued) Symbol Recommended Value Unit MVIN GND to GVDD V MVREF GND to GVDD/2 V Three-speed Ethernet signals LVIN GND to LVDD V PCI/PCI-X, local bus, RapidIO, 10/100 Ethernet, MII management, DUART, SYSCLK, system control and power management, I2C, and JTAG signals OVIN GND to OVDD V Tj 0 to 105 •C Characteristic Input voltage DDR DRAM signals DDR DRAM reference Die-junction temperature Figure 2 shows the undershoot and overshoot voltages at the interfaces of the MPC8540. G/L/OVDD + 20% G/L/OVDD + 5% VIH G/L/OVDD GND GND – 0.3 V VIL GND – 0.7 V Not to Exceed 10% of tSYS1 Note: tSYS refers to the clock period associated with the SYSCLK signal. Figure 2. Overshoot/Undershoot Voltage for GVDD/OVDD/LVDD The MPC8540 core voltage must always be provided at nominal 1.2 V (see Table 2 for actual recommended core voltage). Voltage to the processor interface I/Os are provided through separate sets of supply pins and must be provided at the voltages shown in Table 2. The input voltage threshold scales with respect to the associated I/O supply voltage. OVDD and LVDD based receivers are simple CMOS I/O circuits and satisfy appropriate LVCMOS type specifications. The DDR SDRAM interface uses a single-ended differential receiver referenced the externally supplied MVREF signal (nominally set to GVDD/2) as is appropriate for the SSTL2 electrical signaling standard. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 10 Freescale Semiconductor Electrical Characteristics Figure 3 shows the undershoot and overshoot voltage of the PCI interface of the MPC8540 for the 3.3-V signals, respectively. 11 ns (Min) +7.1 V Overvoltage Waveform 7.1 V p-to-p (Min) 4 ns (Max) 0V 4 ns (Max) 62.5 ns +3.6 V 7.1 V p-to-p (Min) Undervoltage Waveform –3.5 V Figure 3. Maximum AC Waveforms on PCI interface for 3.3-V Signaling 2.1.4 Output Driver Characteristics Table 3 provides information on the characteristics of the output driver strengths. The values are preliminary estimates. Table 3. Output Drive Capability Driver Type Local bus interface utilities signals Programmable Output Impedance (Ω) Supply Voltage Notes 25 OVDD = 3.3 V 1 42 (default) PCI signals 25 2 42 (default) DDR signal 20 GVDD = 2.5 V TSEC/10/100 signals 42 LVDD = 2.5/3.3 V DUART, system control, I2C, JTAG 42 OVDD = 3.3 V RapidIO N/A (LVDS signaling) N/A Notes: 1. The drive strength of the local bus interface is determined by the configuration of the appropriate bits in PORIMPSCR. 2. The drive strength of the PCI interface is determined by the setting of the PCI_GNT1 signal at reset. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 11 Power Characteristics 3 Power Characteristics The estimated power dissipation on the VDD supply for the MPC8540 is shown in Table 4. Table 4. MPC8540 VDD Power Dissipation 1,2 CCB Frequency (MHz) 200 267 333 Core Typical Power3,4 Frequency (MHz) Maximum Power5 Unit W 400 4.6 7.2 500 4.9 7.5 600 5.3 7.9 533 5.5 8.2 667 5.9 8.7 800 6.4 10.2 667 6.3 9.3 833 6.9 10.9 1000 6 11.3 15.9 W W Notes: 1. The values do not include I/O supply power (OVDD, LVDD, GVDD) or AVDD. 2. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, air flow, power dissipation of other components on the board, and board thermal resistance. Any customer design must take these considerations into account to ensure the maximum 105 °C junction temperature is not exceeded on this device. 3. Typical Power is based on a nominal voltage of VDD = 1.2 V, a nominal process, a junction temperature of Tj = 105 °C, and a Dhrystone 2.1 benchmark application. 4. Thermal solutions will likely need to design to a number higher than Typical Power based on the end application, TA target, and I/O power. 5. Maximum power is based on a nominal voltage of VDD = 1.2 V, worst case process, a junction temperature of Tj = 105 °C, and an artificial smoke test. 6. The nominal recommended VDD is 1.3 V for this speed grade. The estimated power dissipation on the AVDD supplies for the MPC8540 PLLs is shown in Table 5. Table 5. MPC8540 AVDD Power Dissipation AVDDn Typical1 Unit AVDD1 0.007 W AVDD2 0.014 W Notes: 1. VDD = 1.2 V (1.3 V for 1.0 GHz device), TJ = 105°C MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 12 Freescale Semiconductor Power Characteristics Table 6 provides estimated I/O power numbers for each block: DDR, PCI, Local Bus, RapidIO, TSEC, and FEC. Table 6. Estimated Typical I/O Power Consumption Interface Parameter GVDD (2.5 V) DDR I/O CCB = 200 MHz 0.46 CCB = 266 MHz 0.59 CCB = 300 MHz 0.66 CCB = 333 MHz 0.73 PCI/PCI-X I/O OVDD (3.3 V) 32-bit, 33 MHz 0.04 32-bit 66 MHz 0.07 64-bit, 66 MHz 0.14 64-bit, 133 MHz 0.25 32-bit, 33 MHz 0.07 32-bit, 66 MHz 0.13 32-bit, 133 MHz 0.24 32-bit, 167 MHz 0.30 RapidIO I/O 500 MHz data rate 0.96 TSEC I/O MII Local Bus I/O LVDD (3.3 V) 10 GMII, TBI (2.5 V) Notes W 1 W 2 W 3 W 4 mW 5, 6 mW 7 70 RGMII, RTBI MII Units 40 GMII, TBI (3.3 V) FEC I/O LVDD (2.5 V) 40 10 Notes: 1. GVDD=2.5, ECC enabled, 66% bus utilization, 33% write cycles, 10pF load on data, 10pF load on address/command, 10pF load on clock 2. OVDD=3.3, 30pF load per pin, 54% bus utilization, 33% write cycles 3. OVDD=3.3, 25pF load per pin, 5pF load on clock, 40% bus utilization, 33% write cycles 4. VDD=1.2, OVDD=3.3 5. LVDD=2.5/3.3, 15pF load per pin, 25% bus utilization 6. Power dissipation for one TSEC only 7. OVDD=3.3, 20pF load per pin, 25% bus utilization MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 13 Clock Timing 4 Clock Timing 4.1 System Clock Timing Table 7 provides the system clock (SYSCLK) AC timing specifications for the MPC8540. Table 7. SYSCLK AC Timing Specifications Parameter/Condition Symbol Min Typical Max Unit Notes SYSCLK frequency fSYSCLK — — 166 MHz 1 SYSCLK cycle time tSYSCLK 6.0 — — ns SYSCLK rise and fall time tKH, tKL 0.6 1.0 1.2 ns 2 tKHKL/tSYSCLK 40 — 60 % 3 — — — +/- 150 ps 4, 5 SYSCLK duty cycle SYSCLK jitter Notes: 1.Caution: The CCB to SYSCLK ratio and e500 core to CCB ratio settings must be chosen such that the resulting SYSCLK frequency, e500 (core) frequency, and CCB frequency do not exceed their respective maximum or minimum operating frequencies. Refer to Section 15.2, “Platform/System PLL Ratio,” and Section 15.3, “e500 Core PLL Ratio,” for ratio settings. 2. Rise and fall times for SYSCLK are measured at 0.6 V and 2.7 V. 3. Timing is guaranteed by design and characterization. 4. This represents the total input jitter—short term and long term—and is guaranteed by design. 5. For spread spectrum clocking, guidelines are +/-1% of the input frequency with a maximum of 60 kHz of modulation regardless of the input frequency. 4.2 TSEC Gigabit Reference Clock Timing Table 7 provides the TSEC gigabit reference clock (EC_GTX_CLK125) AC timing specifications for the MPC8540. Table 8. EC_GTX_CLK125 AC Timing Specifications Parameter/Condition Symbol Min Typical Max Unit EC_GTX_CLK125 frequency fG125 — 125 — MHz EC_GTX_CLK125 cycle time tG125 — 8 — ns tG125R, tG125F — — EC_GTX_CLK125 rise and fall time tG125H/tG125 GMII, TBI RGMII, RTBI ns 2 % 1,3 0.75 1 LVDD=2.5 LVDD=3.3 EC_GTX_CLK125 duty cycle Notes — 45 47 55 53 Notes: 1. Timing is guaranteed by design and characterization. 2. Rise and fall times for EC_GTX_CLK125 are measured from 0.5V and 2.0V for LVDD=2.5V, and from 0.6 and 2.7V for LVDD=3.3V. 3. EC_GTX_CLK125 is used to generate GTX clock for TSEC transmitter with 2% degradation EC_GTX_CLK125 duty cycle can be loosened from 47/53% as long as PHY device can tolerate the duty cycle generated by GTX_CLK of TSEC. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 14 Freescale Semiconductor RESET Initialization 4.3 RapidIO Transmit Clock Input Timing Table 9 provides the RapidIO transmit clock input (RIO_TX_CLK_IN) AC timing specifications for the MPC8540. Table 9. RIO_TX_CLK_IN AC Timing Specifications Parameter/Condition Symbol Min Typical Max Unit RIO_TX_CLK_IN frequency fRCLK 125 — — MHz RIO_TX_CLK_IN cycle time tRCLK — — 8 ns RIO_TX_CLK_IN duty cycle tRCLKH/tRCLK 48 — 52 % Notes 1 Notes: 1. Requires ±100 ppm long term frequency stability. Timing is guaranteed by design and characterization. 4.4 Real Time Clock Timing Table 10 provides the real time clock (RTC) AC timing specifications for the MPC8540. Table 10. RTC AC Timing Specifications Parameter/Condition Symbol Min Typical Max Unit RTC clock high time tRTCH 2x tCCB_CLK — — ns RTC clock low time tRTCL 2x tCCB_CLK — — ns Notes 5 RESET Initialization This section describes the AC electrical specifications for the RESET initialization timing requirements of the MPC8540. Table 7 provides the RESET initialization AC timing specifications for the MPC8540. Table 11. RESET Initialization Timing Specifications Parameter/Condition Min Max Unit Notes Required assertion time of HRESET 100 — μs Minimum assertion time for SRESET 512 — SYSCLKs PLL input setup time with stable SYSCLK before HRESET negation 100 — μs Input setup time for POR configs (other than PLL config) with respect to negation of HRESET 4 — SYSCLKs 1 Input hold time for POR configs (including PLL config) with respect to negation of HRESET 2 — SYSCLKs 1 1 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 15 DDR SDRAM Table 11. RESET Initialization Timing Specifications (continued) Parameter/Condition Min Max Unit Notes Maximum valid-to-high impedance time for actively driven POR configs with respect to negation of HRESET — 5 SYSCLKs 1 Notes: 1.SYSCLK is identical to the PCI_CLK signal and is the primary clock input for the MPC8540. See the MPC8540 Integrated Processor Preliminary Reference Manual for more details. Table 12 provides the PLL and DLL lock times. Table 12. PLL and DLL Lock Times Parameter/Condition Min Max Unit Notes PLL lock times — 100 μs DLL lock times 7680 122,880 CCB Clocks 1, 2 Notes: 1.DLL lock times are a function of the ratio between the output clock and the platform (or CCB) clock. A 2:1 ratio results in the minimum and an 8:1 ratio results in the maximum. 2. The CCB clock is determined by the SYSCLK × platform PLL ratio. 6 DDR SDRAM This section describes the DC and AC electrical specifications for the DDR SDRAM interface of the MPC8540. 6.1 DDR SDRAM DC Electrical Characteristics Table 13 provides the recommended operating conditions for the DDR SDRAM component(s) of the MPC8540. Table 13. DDR SDRAM DC Electrical Characteristics Parameter/Condition Symbol Min Max Unit Notes I/O supply voltage GVDD 2.375 2.625 V 1 I/O reference voltage MVREF 0.49 × GVDD 0.51 × GVDD V 2 I/O termination voltage VTT MVREF – 0.04 MVREF + 0.04 V 3 Input high voltage VIH MVREF + 0.18 GVDD + 0.3 V 4 Input low voltage VIL –0.3 MVREF – 0.18 V 4 Output leakage current IOZ –10 10 μA 5 Output high current (VOUT = 1.95 V) IOH –15.2 — mA Output low current (VOUT = 0.35 V) IOL 15.2 — mA MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 16 Freescale Semiconductor DDR SDRAM Table 13. DDR SDRAM DC Electrical Characteristics (continued) Parameter/Condition MVREF input leakage current Symbol Min Max Unit IVREF — 100 μA Notes Notes: 1.GVDD is expected to be within 50 mV of the DRAM GVDD at all times. 2.MVREF is expected to be equal to 0.5 × GVDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak noise on MVREF may not exceed ±2% of the DC value. 3.VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be equal to MVREF. This rail should track variations in the DC level of MVREF. 4.VIH can tolerate an overshoot of 1.2V over GVDD for a pulse width of ≤3 ns, and the pulse width cannot be greater than tMCK. VIL can tolerate an undershoot of 1.2V below GND for a pulse width of ≤3 ns, and the pulse width cannot be greater than tMCK. 5.Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD. Table 14 provides the DDR capacitance. Table 14. DDR SDRAM Capacitance Parameter/Condition Symbol Min Max Unit Notes Input/output capacitance: DQ, DQS, MSYNC_IN CIO 6 8 pF 1 Delta input/output capacitance: DQ, DQS CDIO — 0.5 pF 1 Note: 1.This parameter is sampled. GVDD = 2.5 V ± 0.125 V, f = 1 MHz, TA = 25°C, VOUT = GVDD/2, VOUT (peak to peak) = 0.2 V. 6.2 DDR SDRAM AC Electrical Characteristics This section provides the AC electrical characteristics for the DDR SDRAM interface. 6.2.1 DDR SDRAM Input AC Timing Specifications Table 15 provides the input AC timing specifications for the DDR SDRAM interface. Table 15. DDR SDRAM Input AC Timing Specifications At recommended operating conditions with GVDD of 2.5 V ± 5%. Parameter Symbol Min Max Unit AC input low voltage VIL — MVREF – 0.31 V AC input high voltage VIH MVREF + 0.31 GVDD + 0.3 V -750 -1125 750 1125 MDQS—MDQ/MECC input skew per byte For DDR = 333 MHz For DDR ≤ 266 MHz tDISKEW ps Notes 1, 2 Note: 1.Maximum possible skew between a data strobe (MDQS[n]) and any corresponding bit of data (MDQ[8n + {0...7}] if 0 ≤ n ≤ 7) or ECC (MECC[{0...7}] if n=8). 2.For timing budget analysis, the MPC8540 consumes ±550 ps of the total budget. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 17 DDR SDRAM MDQS[n] MDQ[n] tDISKEW tDISKEW Figure 4. DDR SDRAM Interface Input Timing 6.2.2 DDR SDRAM Output AC Timing Specifications For chip selects MCS1 and MCS2, there will always be at least 200 DDR memory clocks coming out of self-refresh after an HRESET before a precharge occurs. This will not necessarily be the case for chip selects MCS0 and MCS3. 6.2.2.1 DLL Enabled Mode Table 16 and Table 17 provide the output AC timing specifications and measurement conditions for the DDR SDRAM interface with the DDR DLL enabled. Table 16. DDR SDRAM Output AC Timing Specifications–DLL Mode At recommended operating conditions with GVDD of 2.5 V ± 5%. Parameter Symbol 1 Min Max Unit Notes MCK[n] cycle time, (MCK[n]/MCK[n] crossing) tMCK 6 10 ns 2 On chip Clock Skew tMCKSKEW — 150 ps 3, 8 MCK[n] duty cycle tMCKH/tMCK 45 55 % 8 ADDR/CMD output valid tDDKHOV — 3 ns 4, 9 ADDR/CMD output invalid tDDKHOX 1 — ns 4, 9 Write CMD to first MDQS capture edge tDDSHMH tMCK + 1.5 tMCK + 4.0 ns 5 MDQ/MECC/MDM output setup with respect to MDQS 333 MHz 266 MHz 200 MHz tDDKHDS, tDDKLDS — ps 6, 9 MDQ/MECC/MDM output hold with respect to MDQS 333 MHz 266 MHz 200 MHz tDDKHDX, tDDKLDX — ps 6, 9 MDQS preamble start tDDSHMP 0.75 × tMCK + 4.0 ns 7, 8 900 1100 1200 900 1100 1200 0.75 × tMCK + 1.5 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 18 Freescale Semiconductor DDR SDRAM Table 16. DDR SDRAM Output AC Timing Specifications–DLL Mode (continued) At recommended operating conditions with GVDD of 2.5 V ± 5%. Parameter MDQS epilogue end Symbol 1 Min Max Unit Notes tDDSHME 1.5 4.0 ns 7, 8 Notes: 1.The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing (DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (OX or DX). For example, tDDKHOV symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs (O) are valid (V) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes low (L) until data outputs (D) are invalid (X) or data output hold time. 2.All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V. 3.Maximum possible clock skew between a clock MCK[n] and its relative inverse clock MCK[n], or between a clock MCK[n] and a relative clock MCK[m] or MSYNC_OUT. Skew measured between complementary signals at GVDD/2. 4.ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK and MDQ/MECC/MDM/MDQS. 5.Note that tDDSHMH follows the symbol conventions described in note 1. For example, tDDSHMH describes the DDR timing (DD) from the rising edge of the MSYNC_IN clock (SH) until the MDQS signal is valid (MH). tDDSHMH can be modified through control of the DQSS override bits in the TIMING_CFG_2 register. These controls allow the relationship between the synchronous clock control timing and the source-synchronous DQS domain to be modified by the user. For best turnaround times, these may need to be set to delay tDDSHMH an additional 0.25tMCK. This will also affect tDDSHMP and tDDSHME accordingly. See the MPC8540 PowerQUICC III Integrated Host Processor Reference Manual for a description and understanding of the timing modifications enabled by use of these bits. 6.Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), ECC (MECC), or data mask (MDM). The data strobe should be centered inside of the data eye at the pins of the MPC8540. 7.All outputs are referenced to the rising edge of MSYNC_IN (S) at the pins of the MPC8540. Note that tDDSHMP follows the symbol conventions described in note 1. For example, tDDSHMP describes the DDR timing (DD) from the rising edge of the MSYNC_IN clock (SH) for the duration of the MDQS signal precharge period (MP). 8.Guaranteed by design. 9.Guaranteed by characterization. Figure 5 provides the AC test load for the DDR bus. Z0 = 50 Ω Output RL = 50 Ω GVDD/2 Figure 5. DDR AC Test Load Table 17. DDR SDRAM Measurement Conditions Symbol VTH VOUT DDR Unit Notes MVREF ± 0.31 V V 1 0.5 × GVDD V 2 Notes: 1.Data input threshold measurement point. 2.Data output measurement point. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 19 DDR SDRAM Figure 6 shows the DDR SDRAM output timing diagram. MCK[n] MCK[n] tMCK tMCK tMCKH MSYNC_OUT DLL Phase Alignment MSYNC_IN tDDKHOV tDDKHOX ADDR/CMD Write A0 NOOP tDDSHMH MDQS[n] tDDSHMP tDDKHDS tDDSHME tDDKLDS MDQ[x] D0 D1 tDDKLDX tDDKHDX Figure 6. DDR SDRAM Output Timing Diagram 6.2.2.2 Load Effects on Address/Command Bus Table 18 provides approximate delay information that can be expected for the address and command signals of the DDR controller for various loadings. These numbers are the result of simulations for one topology. The delay numbers will strongly depend on the topology used. These delay numbers show the total delay for the address and command to arrive at the DRAM devices. The actual delay could be different than the delays seen in simulation, depending on the system topology. If a heavily loaded system is used, the DLL loop may need to be adjusted to meet setup requirements at the DRAM. Table 18. Expected Delays for Address/Command Load Delay Unit 4 devices (12 pF) 3.0 ns 9 devices (27 pF) 3.6 ns 36 devices (108 pF) + 40 pF compensation capacitor 5.0 ns 36 devices (108 pF) + 80 pF compensation capacitor 5.2 ns MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 20 Freescale Semiconductor DUART 7 DUART This section describes the DC and AC electrical specifications for the DUART interface of the MPC8540. 7.1 DUART DC Electrical Characteristics Table 19 provides the DC electrical characteristics for the DUART interface of the MPC8540. Table 19. DUART DC Electrical Characteristics Parameter Symbol Min Max Unit High-level input voltage VIH 2 OVDD + 0.3 V Low-level input voltage VIL –0.3 0.8 V Input current (VIN 1 = 0 V or VIN = VDD) IIN — ±5 μA High-level output voltage (OVDD = min, IOH = –100 μA) VOH OVDD – 0.2 — V Low-level output voltage (OVDD = min, IOL = 100 μA) VOL — 0.2 V Note: 1.Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 7.2 DUART AC Electrical Specifications Table 20 provides the AC timing parameters for the DUART interface of the MPC8540. Table 20. DUART AC Timing Specifications Parameter Value Unit Notes Minimum baud rate fCCB_CLK / 1048576 baud 3 Maximum baud rate fCCB_CLK / 16 baud 1, 3 16 — 2, 3 Oversample rate Notes: 1.Actual attainable baud rate will be limited by the latency of interrupt processing. 2.The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit values are sampled each 16th sample. 3.Guaranteed by design. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 21 Ethernet: Three-Speed,10/100, MII Management 8 Ethernet: Three-Speed,10/100, MII Management This section provides the AC and DC electrical characteristics for three-speed, 10/100, and MII management. 8.1 Three-Speed Ethernet Controller (TSEC) (10/100/1Gb Mbps)—GMII/MII/TBI/RGMII/RTBI Electrical Characteristics The electrical characteristics specified here apply to all GMII (gigabit media independent interface), MII (media independent interface), TBI (ten-bit interface), RGMII (reduced gigabit media independent interface), and RTBI (reduced ten-bit interface) signals except MDIO (management data input/output) and MDC (management data clock). The RGMII and RTBI interfaces are defined for 2.5 V, while the GMII, MII, and TBI interfaces can be operated at 3.3 or 2.5 V. Whether the GMII, MII, or TBI interface is operated at 3.3 or 2.5 V, the timing is compliant with the IEEE 802.3 standard. The RGMII and RTBI interfaces follow the Hewlett-Packard reduced pin-count interface for Gigabit Ethernet Physical Layer Device Specification Version 1.2a (9/22/2000). The electrical characteristics for MDIO and MDC are specified in Section 8.4, “Ethernet Management Interface Electrical Characteristics.” 8.1.1 TSEC DC Electrical Characteristics All GMII, MII, TBI, RGMII, and RTBI drivers and receivers comply with the DC parametric attributes specified in Table 21 and Table 22. The potential applied to the input of a GMII, MII, TBI, RGMII, or RTBI receiver may exceed the potential of the receiver’s power supply (i.e., a GMII driver powered from a 3.6 V supply driving VOH into a GMII receiver powered from a 2.5 V supply). Tolerance for dissimilar GMII driver and receiver supply potentials is implicit in these specifications. The RGMII and RTBI signals are based on a 2.5 V CMOS interface voltage as defined by JEDEC EIA/JESD8-5. Table 21. GMII, MII, and TBI DC Electrical Characteristics Parameter Symbol Min Max Unit Supply voltage 3.3 V LVDD 3.13 3.47 V Output high voltage (LVDD = Min, IOH = –4.0 mA) VOH 2.40 LVDD + 0.3 V Output low voltage (LVDD = Min, IOL = 4.0 mA) VOL GND 0.50 V Input high voltage VIH 1.70 LVDD + 0.3 V Input low voltage VIL –0.3 0.90 V Input high current (VIN 1 = LVDD) IIH — 40 μA Input low current (VIN 1 = GND) IIL –600 — μA Note: 1.The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 22 Freescale Semiconductor Ethernet: Three-Speed,10/100, MII Management Table 22. GMII, MII, RGMII, RTBI, and TBI DC Electrical Characteristics Parameters Symbol Min Max Unit Supply voltage 2.5 V LVDD 2.37 2.63 V Output high voltage (LVDD = Min, IOH = –1.0 mA) VOH 2.00 LVDD + 0.3 V Output low voltage (LVDD = Min, IOL = 1.0 mA) VOL GND – 0.3 0.40 V Input high voltage VIH 1.70 LVDD + 0.3 V Input low voltage VIL –0.3 0.70 V Input high current (VIN 1 = LVDD) IIH — 10 μA Input low current (VIN 1 = GND) IIL –15 — μA Note: 1.Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1and Table 2. 8.2 GMII, MII, TBI, RGMII, and RTBI AC Timing Specifications The AC timing specifications for GMII, MII, TBI, RGMII, and RTBI are presented in this section. 8.2.1 GMII AC Timing Specifications This section describes the GMII transmit and receive AC timing specifications. 8.2.1.1 GMII Transmit AC Timing Specifications Table 23 provides the GMII transmit AC timing specifications. Table 23. GMII Transmit AC Timing Specifications At recommended operating conditions with LVDD of 3.3 V ± 5%, or LVDD=2.5V ± 5%. Symbol 1 Min Typ Max Unit tGTX — 8.0 — ns tGTXH/tGTX 40 — 60 % GMII data TXD[7:0], TX_ER, TX_EN setup time tGTKHDV 2.5 — — ns GTX_CLK to GMII data TXD[7:0], TX_ER, TX_EN delay tGTKHDX 3 0.5 — 5.0 ns Parameter/Condition GTX_CLK clock period GTX_CLK duty cycle MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 23 Ethernet: Three-Speed,10/100, MII Management Table 23. GMII Transmit AC Timing Specifications (continued) At recommended operating conditions with LVDD of 3.3 V ± 5%, or LVDD=2.5V ± 5%. Parameter/Condition GTX_CLK data clock rise and fall time Symbol 1 Min Typ Max Unit tGTXR, tGTXF 2,4 — — 1.0 ns Notes: 1. The symbols used for timing specifications herein follow the pattern t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tGTKHDV symbolizes GMII transmit timing (GT) with respect to the tGTX clock reference (K) going to the high state (H) relative to the time date input signals (D) reaching the valid state (V) to state or setup time. Also, tGTKHDX symbolizes GMII transmit timing (GT) with respect to the tGTX clock reference (K) going to the high state (H) relative to the time date input signals (D) going invalid (X) or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tGTX represents the GMII(G) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2.Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3.Guaranteed by characterization. 4.Guaranteed by design. Figure 7 shows the GMII transmit AC timing diagram. tGTXR tGTX GTX_CLK tGTXH tGTXF TXD[7:0] TX_EN TX_ER tGTKHDX tGTKHDV Figure 7. GMII Transmit AC Timing Diagram 8.2.1.2 GMII Receive AC Timing Specifications Table 24 provides the GMII receive AC timing specifications. Table 24. GMII Receive AC Timing Specifications At recommended operating conditions with LVDD of 3.3 V ± 5%, or LVDD=2.5V ± 5%. Symbol 1 Min Typ Max Unit tGRX — 8.0 — ns tGRXH/tGRX 40 — 60 ns RXD[7:0], RX_DV, RX_ER setup time to RX_CLK tGRDVKH 2.0 — — ns RXD[7:0], RX_DV, RX_ER hold time to RX_CLK tGRDXKH 0.5 — — ns Parameter/Condition RX_CLK clock period RX_CLK duty cycle MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 24 Freescale Semiconductor Ethernet: Three-Speed,10/100, MII Management Table 24. GMII Receive AC Timing Specifications (continued) At recommended operating conditions with LVDD of 3.3 V ± 5%, or LVDD=2.5V ± 5%. Parameter/Condition RX_CLK clock rise and fall time Symbol 1 Min Typ Max Unit tGRXR, tGRXF 2,3 — — 1.0 ns Note: 1.The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tGRDVKH symbolizes GMII receive timing (GR) with respect to the time data input signals (D) reaching the valid state (V) relative to the tRX clock reference (K) going to the high state (H) or setup time. Also, tGRDXKL symbolizes GMII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tGRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tGRX represents the GMII (G) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2.Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3.Guaranteed by design. Figure 8 provides the AC test load for TSEC. Z0 = 50 Ω Output RL = 50 Ω LVDD/2 Figure 8. TSEC AC Test Load Figure 9 shows the GMII receive AC timing diagram. tGRXR tGRX RX_CLK tGRXH tGRXF RXD[7:0] RX_DV RX_ER tGRDXKH tGRDVKH Figure 9. GMII Receive AC Timing Diagram MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 25 Ethernet: Three-Speed,10/100, MII Management 8.2.2 MII AC Timing Specifications This section describes the MII transmit and receive AC timing specifications. 8.2.2.1 MII Transmit AC Timing Specifications Table 25 provides the MII transmit AC timing specifications. Table 25. MII Transmit AC Timing Specifications At recommended operating conditions with LVDD of 3.3 V ± 5%, or LVDD=2.5V ± 5%. Symbol 1 Min Typ Max Unit TX_CLK clock period 10 Mbps tMTX 2 — 400 — ns TX_CLK clock period 100 Mbps tMTX — 40 — ns tMTXH/tMTX 35 — 65 % tMTKHDX 1 5 15 ns tMTXR, tMTXF 2,3 1.0 — 4.0 ns Parameter/Condition TX_CLK duty cycle TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay TX_CLK data clock rise and fall time Note: 1.The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing (MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tMTX represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2.Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3.Guaranteed by design. Figure 10 shows the MII transmit AC timing diagram. tMTXR tMTX TX_CLK tMTXH tMTXF TXD[3:0] TX_EN TX_ER tMTKHDX Figure 10. MII Transmit AC Timing Diagram MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 26 Freescale Semiconductor Ethernet: Three-Speed,10/100, MII Management 8.2.2.2 MII Receive AC Timing Specifications Table 26 provides the MII receive AC timing specifications. Table 26. MII Receive AC Timing Specifications At recommended operating conditions with LVDD of 3.3 V ± 5%, or LVDD=2.5V ± 5%. Symbol 1 Min Typ Max Unit RX_CLK clock period 10 Mbps tMRX 3 — 400 — ns RX_CLK clock period 100 Mbps tMRX — 40 — ns tMRXH/tMRX 35 — 65 % RXD[3:0], RX_DV, RX_ER setup time to RX_CLK tMRDVKH 10.0 — — ns RXD[3:0], RX_DV, RX_ER hold time to RX_CLK tMRDXKH 10.0 — — ns tMRXR, tMRXF 2,3 1.0 — 4.0 ns Parameter/Condition RX_CLK duty cycle RX_CLK clock rise and fall time Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2.Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3.Guaranteed by design. Figure 11 shows the MII receive AC timing diagram. tMRXR tMRX RX_CLK tMRXH RXD[3:0] RX_DV RX_ER tMRXF Valid Data tMRDVKH tMRDXKH Figure 11. MII Receive AC Timing Diagram MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 27 Ethernet: Three-Speed,10/100, MII Management 8.2.3 TBI AC Timing Specifications This section describes the TBI transmit and receive AC timing specifications. 8.2.3.1 TBI Transmit AC Timing Specifications Table 27 provides the TBI transmit AC timing specifications. Table 27. TBI Transmit AC Timing Specifications At recommended operating conditions with LVDD of 3.3 V ± 5%, or LVDD=2.5V ± 5%. Symbol 1 Min Typ Max Unit tTTX — 8.0 — ns tTTXH/tTTX 40 — 60 % TCG[9:0] setup time GTX_CLK going high tTTKHDV 2.0 — — ns TCG[9:0] hold time from GTX_CLK going high tTTKHDX 1.0 — — ns — — 1.0 ns Parameter/Condition GTX_CLK clock period GTX_CLK duty cycle GTX_CLK clock rise and fall time tTTXR, tTTXF 2,3 Notes: 1.The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state )(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tTTKHDV symbolizes the TBI transmit timing (TT) with respect to the time from tTTX (K) going high (H) until the referenced data signals (D) reach the valid state (V) or setup time. Also, tTTKHDX symbolizes the TBI transmit timing (TT) with respect to the time from tTTX (K) going high (H) until the referenced data signals (D) reach the invalid state (X) or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tTTX represents the TBI (T) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2.Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3.Guaranteed by design. Figure 12 shows the TBI transmit AC timing diagram. tTTXR tTTX GTX_CLK tTTXH tTTXF TCG[9:0] tTTKHDV tTTKHDX Figure 12. TBI Transmit AC Timing Diagram MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 28 Freescale Semiconductor Ethernet: Three-Speed,10/100, MII Management 8.2.3.2 TBI Receive AC Timing Specifications Table 28 provides the TBI receive AC timing specifications. Table 28. TBI Receive AC Timing Specifications At recommended operating conditions with LVDD of 3.3 V ± 5%, or LVDD=2.5V ± 5%. Symbol 1 Parameter/Condition RX_CLK clock period Min Max 16.0 tTRX RX_CLK skew Typ Unit ns tSKTRX 7.5 — 8.5 ns tTRXH/tTRX 40 — 60 % RCG[9:0] setup time to rising RX_CLK tTRDVKH 2.5 — — ns RCG[9:0] hold time to rising RX_CLK tTRDXKH 1.5 — — ns RX_CLK clock rise time and fall time tTRXR, tTRXF 2,3 0.7 — 2.4 ns RX_CLK duty cycle Note: 1.The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tTRDVKH symbolizes TBI receive timing (TR) with respect to the time data input signals (D) reach the valid state (V) relative to the tTRX clock reference (K) going to the high (H) state or setup time. Also, tTRDXKH symbolizes TBI receive timing (TR) with respect to the time data input signals (D) went invalid (X) relative to the tTRX clock reference (K) going to the high (H) state. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tTRX represents the TBI (T) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). For symbols representing skews, the subscript is skew (SK) followed by the clock that is being skewed (TRX). 2.Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3.Guaranteed by design. Figure 13 shows the TBI receive AC timing diagram. tTRXR tTRX RX_CLK1 tTRXH tTRXF Valid Data RCG[9:0] Valid Data tTRDVKH tSKTRX tTRDXKH RX_CLK0 tTRDXKH tTRXH tTRDVKH Figure 13. TBI Receive AC Timing Diagram MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 29 Ethernet: Three-Speed,10/100, MII Management 8.2.4 RGMII and RTBI AC Timing Specifications Table 29 presents the RGMII and RTBI AC timing specifications. Table 29. RGMII and RTBI AC Timing Specifications At recommended operating conditions with LVDD of 2.5 V ± 5%. Parameter/Condition Data to clock output skew (at transmitter) Data to clock input skew (at receiver) 2 Clock period3 Min Typ Max Unit tSKRGT 5 –500 0 500 ps tSKRGT 1.0 — 2.8 ns tRGT 6 Duty cycle for 1000Base-T 4 Duty cycle for 10BASE-T and 100BASE-TX 3 Rise and fall time Symbol 1 7.2 8.0 8.8 ns 6 45 50 55 % tRGTH/tRGT 6 40 50 60 % — — 0.75 ns tRGTH/tRGT tRGTR, tRGTF 6,7 Notes: 1.Note that, in general, the clock reference symbol representation for this section is based on the symbols RGT to represent RGMII and RTBI timing. For example, the subscript of tRGT represents the TBI (T) receive (RX) clock. Note also that the notation for rise (R) and fall (F) times follows the clock symbol that is being represented. For symbols representing skews, the subscript is skew (SK) followed by the clock that is being skewed (RGT). 2.The RGMII specification requires that PC board designer add 1.5 ns or greater in trace delay to the RX_CLK in order to meet this specification. However, as stated above, this device will function with only 1.0 ns of delay. 3.For 10 and 100 Mbps, tRGT scales to 400 ns ± 40 ns and 40 ns ± 4 ns, respectively. 4.Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet's clock domains as long as the minimum duty cycle is not violated and stretching occurs for no more than three tRGT of the lowest speed transitioned between. 5.Guaranteed by characterization. 6.Guaranteed by design. 7.Signal timings are measured at 0.5 V and 2.0 V voltage levels. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 30 Freescale Semiconductor Ethernet: Three-Speed,10/100, MII Management Figure 14 shows the RGMII and RTBI AC timing and multiplexing diagrams. tRGT tRGTH GTX_CLK (At Transmitter) tSKRGT TXD[8:5][3:0] TXD[7:4][3:0] TX_CTL TXD[3:0] TXD[8:5] TXD[7:4] TXD[4] TXEN TXD[9] TXERR tSKRGT TX_CLK (At PHY) RXD[8:5][3:0] RXD[7:4][3:0] RXD[8:5] RXD[3:0] RXD[7:4] tSKRGT RX_CTL RXD[4] RXDV RXD[9] RXERR tSKRGT RX_CLK (At PHY) Figure 14. RGMII and RTBI AC Timing and Multiplexing Diagrams 8.3 10/100 Ethernet Controller (10/100 Mbps)—MII Electrical Characteristics The electrical characteristics specified here apply to the MII (media independent interface) signals except MDIO (management data input/output) and MDC (management data clock). The MII interface can be operated at 3.3 or 2.5 V. Whether the MII interface is operated at 3.3 or 2.5 V, the timing is compliant with the IEEE 802.3 standard. The electrical characteristics for MDIO and MDC are specified in Section 2.1.3, “Recommended Operating Conditions.” 8.3.1 MII DC Electrical Characteristics All MII drivers and receivers comply with the DC parametric attributes specified in Table 30. The potential applied to the input of a MII receiver may exceed the potential of the receiver’s power supply (that is, a MII driver powered from a 3.6-V supply driving VOH into a MII receiver powered from a 2.5-V supply). Tolerance for dissimilar MII driver and receiver supply potentials is implicit in these specifications. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 31 Ethernet: Three-Speed,10/100, MII Management Table 30. MII DC Electrical Characteristics Parameter Symbol Min Max Unit OVDD 3.13 3.47 V Output high voltage (OVDD = Min, IOH = –4.0 mA) VOH 2.40 OVDD + 0.3 V Output low voltage (OVDD = Min, IOL = 4.0 mA) VOL GND 0.50 V Input high voltage VIH 1.70 — V Input low voltage VIL –0.3 0.90 V Input high current (VIN= OVDD 1) IIH — 40 μA Input low current (VIN= GND 1) IIL –600 — μA Supply voltage 3.3 V Note: 1.Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 8.3.2 MII AC Electrical Specifications This section describes the MII transmit and receive AC specifications. 8.3.2.1 MII Transmit AC Timing Specifications Table 31 provides the MII transmit AC timing specifications. Table 31. MII Transmit AC Timing Specifications At recommended operating conditions with OVDD of 3.3 V ± 5%. Symbol 1 Min Typ Max Unit TX_CLK clock period 10 Mbps tMTX — 400 — ns TX_CLK clock period 100 Mbps tMTX — 40 — ns tMTXH/tMTX 35 — 65 % tMTKHDX 1 5 15 ns 1.0 — 4.0 ns Parameter/Condition TX_CLK duty cycle TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay TX_CLK data clock rise and fall time tMTXR, tMTXF 2,3 Note: 1.The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing (MT) from the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tMTX represents the MII (M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2.Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3.Guaranteed by design. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 32 Freescale Semiconductor Ethernet: Three-Speed,10/100, MII Management Figure 15 shows the MII transmit AC timing diagram. tMTXR tMTX TX_CLK tMTXH tMTXF TXD[3:0] TX_EN TX_ER tMTKHDX Figure 15. MII Transmit AC Timing Diagram 8.3.2.2 MII Receive AC Timing Specifications Table 32 provides the MII receive AC timing specifications. Table 32. MII Receive AC Timing Specifications Symbol 1 Min Typ Max Unit RX_CLK clock period 10 Mbps tMRX — 400 — ns RX_CLK clock period 100 Mbps tMRX — 40 — ns tMRXH/tMRX 35 — 65 % RXD[7:0], TX_DV, TX_ER setup time to RX_CLK tMRDVKH 10.0 — — ns RXD[7:0], TX_DV, TX_ER hold time to RX_CLK tMRDXKH 10.0 — — ns tMRXR, tMRXF 2,3 1.0 — 4.0 ns Parameter/Condition RX_CLK duty cycle RX_CLK clock rise and fall time Note: 1.The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to the high (H) state or setup time. Also, tMRDXKH symbolizes MII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the high (H) state or hold time. Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2.Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3.Guaranteed by design. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 33 Ethernet: Three-Speed,10/100, MII Management Figure 16 shows the MII receive AC timing diagram. tMRXR tMRX RX_CLK tMRXF tMRXH RXD[3:0] RX_DV RX_ER Valid Data tMRDVKH tMRDXKH Figure 16. MII Receive AC Timing Diagram 8.4 Ethernet Management Interface Electrical Characteristics The electrical characteristics specified here apply to MII management interface signals MDIO (management data input/output) and MDC (management data clock). The electrical characteristics for GMII, RGMII, TBI and RTBI are specified in Section 8.1, “Three-Speed Ethernet Controller (TSEC) (10/100/1Gb Mbps)—GMII/MII/TBI/RGMII/RTBI Electrical Characteristics.” 8.4.1 MII Management DC Electrical Characteristics The MDC and MDIO are defined to operate at a supply voltage of 3.3 V. The DC electrical characteristics for MDIO and MDC are provided in Table 33. Table 33. MII Management DC Electrical Characteristics Parameter Symbol Min Max Unit OVDD 3.13 3.47 V Output high voltage (OVDD = Min, IOH = –1.0 mA) VOH 2.10 OVDD + 0.3 V Output low voltage (OVDD = Min, IOL = 1.0 mA) VOL GND 0.50 V Input high voltage VIH 1.70 — V Input low voltage VIL — 0.90 V Input high current (OVDD = Max, VIN 1 = 2.1 V) IIH — 40 μA Input low current (OVDD = Max, VIN = 0.5 V) IIL –600 — μA Supply voltage (3.3 V) Note: 1.Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 34 Freescale Semiconductor Ethernet: Three-Speed,10/100, MII Management 8.4.2 MII Management AC Electrical Specifications Table 34 provides the MII management AC timing specifications. Table 34. MII Management AC Timing Specifications At recommended operating conditions with OVDD is 3.3 V ± 5%. Symbol 1 Min Typ Max Unit Notes MDC frequency fMDC 0.893 — 10.4 MHz 2, 4 MDC period tMDC 96 — 1120 ns MDC clock pulse width high tMDCH 32 — — ns 2*[1/(fccb_clk/8)] ns 3 3 Parameter/Condition MDC to MDIO valid tMDKHDV MDC to MDIO delay tMDKHDX 10 — 2*[1/(fccb_clk/8)] ns MDIO to MDC setup time tMDDVKH 5 — — ns MDIO to MDC hold time tMDDXKH 0 — — ns MDC rise time tMDCR — — 10 ns 4 MDC fall time tMDHF — — 10 ns 4 Notes: 1.The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes management data timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data hold time. Also, tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reach the valid state (V) relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2.This parameter is dependent on the CCB clock speed (that is, for a CCB clock of 267 MHz, the maximum frequency is 8.3 MHz and the minimum frequency is 1.2 MHz; for a CCB clock of 333 MHz, the maximum frequency is 10.4 MHz and the minimum frequency is 1.5 MHz). 3.This parameter is dependent on the CCB clock speed (that is, for a CCB clock of 267 MHz, the delay is 60 ns and for a CCB clock of 333 MHz, the delay is 48 ns). 4.Guaranteed by design. Figure 17 shows the MII management AC timing diagram. tMDCR tMDC MDC tMDCF tMDCH MDIO (Input) tMDDVKH tMDKHDV tMDDXKH MDIO (Output) tMDKHDX Figure 17. MII Management Interface Timing Diagram MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 35 Local Bus 9 Local Bus This section describes the DC and AC electrical specifications for the local bus interface of the MPC8540. 9.1 Local Bus DC Electrical Characteristics Table 35 provides the DC electrical characteristics for the local bus interface. Table 35. Local Bus DC Electrical Characteristics Parameter Symbol Min Max Unit High-level input voltage VIH 2 OVDD + 0.3 V Low-level input voltage VIL –0.3 0.8 V Input current (VIN 1 = 0 V or VIN = VDD) IIN — ±5 μA High-level output voltage (OVDD = min, IOH = –2 mA) VOH OVDD - 0.2 — V Low-level output voltage (OVDD = min, IOL = 2 mA) VOL — 0.2 V Note: 1.Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 9.2 Local Bus AC Electrical Specifications Table 36 describes the general timing parameters of the local bus interface of the MPC8540 with the DLL enabled. Table 36. Local Bus General Timing Parameters - DLL Enabled Symbol 1 Min Max Unit Notes tLBK 6.0 — ns 2 LCLK[n] skew to LCLK[m] or LSYNC_OUT tLBKSKEW — 150 ps 3, 9 Input setup to local bus clock (except LUPWAIT) tLBIVKH1 1.8 — ns 4, 5, 8 LUPWAIT input setup to local bus clock tLBIVKH2 1.7 — ns 4, 5 Input hold from local bus clock (except LUPWAIT) tLBIXKH1 0.5 — ns 4, 5, 8 LUPWAIT input hold from local bus clock tLBIXKH2 1.0 — ns 4, 5 LALE output transition to LAD/LDP output transition (LATCH hold time) tLBOTOT 1.5 — ns 6 Parameter POR Configuration Local bus cycle time MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 36 Freescale Semiconductor Local Bus Table 36. Local Bus General Timing Parameters - DLL Enabled (continued) POR Configuration Symbol 1 Min Max Unit Notes Local bus clock to output valid (except LAD/LDP and LALE) TSEC2_TXD[6:5] = 00 tLBKHOV1 — 2.0 ns 4, 8 Local bus clock to data valid for LAD/LDP TSEC2_TXD[6:5] = 00 ns 4, 8 Local bus clock to address valid for LAD TSEC2_TXD[6:5] = 00 ns 4, 8 Parameter TSEC2_TXD[6:5] = 11 (default) tLBKHOV2 — TSEC2_TXD[6:5] = 11 (default) TSEC2_TXD[6:5] = 00 tLBKHOV3 — TSEC2_TXD[6:5] = 00 Local bus clock to output high Impedance (except LAD/LDP and LALE) TSEC2_TXD[6:5] = 00 Local bus clock to output high impedance for LAD/LDP TSEC2_TXD[6:5] = 00 tLBKHOV4 — 2.3 ns 4, 8 tLBKHOX1 0.7 — ns 4, 8 — ns 4, 8 2.5 ns 7, 9 ns 7, 9 1.6 tLBKHOX2 TSEC2_TXD[6:5] = 11 (default) 0.7 1.6 tLBKHOZ1 — TSEC2_TXD[6:5] = 11 (default) TSEC2_TXD[6:5] = 11 (default) 2.3 3.8 TSEC2_TXD[6:5] = 11 (default) Output hold from local bus clock for LAD/LDP 2.2 3.7 TSEC2_TXD[6:5] = 11 (default) Local bus clock to LALE assertion Output hold from local bus clock (except LAD/LDP and LALE) 3.5 3.8 tLBKHOZ2 — 2.5 3.8 Notes: 1.The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time. 2.All timings are in reference to LSYNC_IN for DLL enabled mode. 3.Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew measured between complementary signals at OVDD/2. 4.All signals are measured from OVDD/2 of the rising edge of LSYNC_IN for DLL enabled to 0.4 × OVDD of the signal in question for 3.3-V signaling levels. 5.Input timings are measured at the pin. 6.The value of tLBOTOT is defined as the sum of 1/2 or 1 ccb_clk cycle as programmed by LBCR[AHD], and the number of local bus buffer delays used as programmed at power-on reset with configuration pins TSEC2_TXD[6:5]. 7. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 8.Guaranteed by characterization. 9.Guaranteed by design. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 37 Local Bus Table 37 describes the general timing parameters of the local bus interface of the MPC8540 with the DLL bypassed. Table 37. Local Bus General Timing Parameters—DLL Bypassed Symbol 1 Min Max Unit Notes tLBK 6.0 — ns 2 tLBKHKT 2.3 3.9 ns 8 LCLK[n] skew to LCLK[m] or LSYNC_OUT tLBKSKEW — 150 ps 3, 9 Input setup to local bus clock (except LUPWAIT) tLBIVKH1 5.7 — ns 4, 5 LUPWAIT input setup to local bus clock tLBIVKH2 5.6 — ns 4, 5 Input hold from local bus clock (except LUPWAIT) tLBIXKH1 -1.8 — ns 4, 5 LUPWAIT input hold from local bus clock tLBIXKH2 -1.3 — ns 4, 5 LALE output transition to LAD/LDP output transition (LATCH hold time) tLBOTOT 1.5 — ns 6 tLBKLOV1 — -0.3 ns 4 ns 4 ns 4 Parameter POR Configuration Local bus cycle time Internal launch/capture clock to LCLK delay Local bus clock to output valid (except LAD/LDP and LALE) TSEC2_TXD[6:5] = 00 TSEC2_TXD[6:5] = 11 (default) Local bus clock to data valid for LAD/LDP TSEC2_TXD[6:5] = 00 1.2 tLBKLOV2 — TSEC2_TXD[6:5] = 11 (default) Local bus clock to address valid for LAD TSEC2_TXD[6:5] = 00 1.4 tLBKLOV3 — TSEC2_TXD[6:5] = 11 (default) Local bus clock to LALE assertion Output hold from local bus clock (except LAD/LDP and LALE) Output hold from local bus clock for LAD/LDP Local bus clock to output high Impedance (except LAD/LDP and LALE) TSEC2_TXD[6:5] = 00 tLBKHOV4 — 0 ns 4 tLBKLOX1 -3.2 — ns 4 — ns 4 0.2 ns 7 -2.3 tLBKLOX2 TSEC2_TXD[6:5] = 11 (default) TSEC2_TXD[6:5] = 00 TSEC2_TXD[6:5] = 11 (default) 0 1.5 TSEC2_TXD[6:5] = 11 (default) TSEC2_TXD[6:5] = 00 -0.1 -3.2 -2.3 tLBKLOZ1 — 1.5 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 38 Freescale Semiconductor Local Bus Table 37. Local Bus General Timing Parameters—DLL Bypassed (continued) Parameter POR Configuration Symbol 1 Min Max Unit Notes Local bus clock to output high impedance for LAD/LDP TSEC2_TXD[6:5] = 00 tLBKLOZ2 — 0.2 ns 7 TSEC2_TXD[6:5] = 11 (default) 1.5 Notes: 1.The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time. 2.All timings are in reference to local bus clock for DLL bypass mode. Timings may be negative with respect to the local bus clock because the actual launch and capture of signals is done with the internal launch/capture clock, which precedes LCLK by tLBKHKT. 3.Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew measured between complementary signals at OVDD/2. 4.All signals are measured from OVDD/2 of the rising edge of local bus clock for DLL bypass mode to 0.4 × OVDD of the signal in question for 3.3-V signaling levels. 5.Input timings are measured at the pin. 6.The value of tLBOTOT is defined as the sum of 1/2 or 1 ccb_clk cycle as programmed by LBCR[AHD], and the number of local bus buffer delays used as programmed at power-on reset with configuration pins TSEC2_TXD[6:5]. 7.For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 8.Guaranteed by characterization. 9.Guaranteed by design. Figure 18 provides the AC test load for the local bus. Output Z0 = 50 Ω RL = 50 Ω OVDD/2 Figure 18. Local Bus AC Test Load MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 39 Local Bus Figure 19 through Figure 24 show the local bus signals. LSYNC_IN tLBIXKH1 tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIXKH2 tLBIVKH2 Input Signal: LGTA Output Signals: LA[27:31]/LBCTL/LBCKE/LOE/ LSDA10/LSDWE/LSDRAS/ LSDCAS/LSDDQM[0:3] tLBKHOV1 tLBKHOZ1 tLBKHOX1 tLBKHOV2 tLBKHOZ2 tLBKHOX2 Output (Data) Signals: LAD[0:31]/LDP[0:3] tLBKHOV3 tLBKHOZ2 tLBKHOX2 Output (Address) Signal: LAD[0:31] tLBOTOT tLBKHOV4 LALE Figure 19. Local Bus Signals, Nonspecial Signals Only (DLL Enabled) MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 40 Freescale Semiconductor Local Bus Internal launch/capture clock tLBKHKT LCLK[n] tLBIVKH1 tLBIXKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIVKH2 Input Signal: LGTA tLBIXKH2 tLBKLOV1 tLBKLOX1 Output Signals: LA[27:31]/LBCTL/LBCKE/LOE/ LSDA10/LSDWE/LSDRAS/ LSDCAS/LSDDQM[0:3] tLBKLOZ1 tLBKLOZ2 tLBKLOV2 Output (Data) Signals: LAD[0:31]/LDP[0:3] tLBKLOX2 tLBKLOV3 Output (Address) Signal: LAD[0:31] tLBKLOV4 tLBOTOT LALE Figure 20. Local Bus Signals (DLL Bypass Mode) MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 41 Local Bus LSYNC_IN T1 T3 tLBKHOV1 tLBKHOZ1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBIVKH2 tLBIXKH2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 tLBIXKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBKHOV1 tLBKHOZ1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] Figure 21. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 (DLL Enabled) MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 42 Freescale Semiconductor Local Bus Internal launch/capture clock tLBKHKT T1 T3 LCLK tLBKLOX1 tLBKLOV1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBIVKH2 UPM Mode Input Signal: LUPWAIT tLBKLOZ1 tLBIXKH2 tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] (DLL Bypass Mode) tLBIXKH1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] Figure 22. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 (DLL Bypass Mode) MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 43 Local Bus LSYNC_IN T1 T2 T3 T4 tLBKHOV1 tLBKHOZ1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBIVKH2 tLBIXKH2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] (DLL Bypass Mode) tLBKHOV1 tLBIXKH1 tLBKHOZ1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] Figure 23. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 or 8 (DLL Enabled) MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 44 Freescale Semiconductor Local Bus Internal launch/capture clock tLBKHKT T1 T2 T3 T4 LCLK tLBKLOX1 tLBKLOV1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBIVKH2 UPM Mode Input Signal: LUPWAIT tLBKLOZ1 tLBIXKH2 tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] (DLL Bypass Mode) tLBIXKH1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] Figure 24. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 or 8 (DLL Bypass Mode) MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 45 JTAG 10 JTAG This section describes the AC electrical specifications for the IEEE 1149.1 (JTAG) interface of the MPC8540. Table 38 provides the JTAG AC timing specifications as defined in Figure 26 through Figure 29. Table 38. JTAG AC Timing Specifications (Independent of SYSCLK) 1 At recommended operating conditions (see Table 2). Symbol 2 Min Max Unit JTAG external clock frequency of operation fJTG 0 33.3 MHz JTAG external clock cycle time t JTG 30 — ns tJTKHKL 15 — ns tJTGR & tJTGF 0 2 ns 6 tTRST 25 — ns 3 Boundary-scan data TMS, TDI tJTDVKH tJTIVKH 4 0 — — Boundary-scan data TMS, TDI tJTDXKH tJTIXKH 20 25 — — Boundary-scan data TDO tJTKLDV tJTKLOV 4 4 20 25 Boundary-scan data TDO tJTKLDX tJTKLOX JTAG external clock to output high impedance: Boundary-scan data TDO tJTKLDZ tJTKLOZ Parameter JTAG external clock pulse width measured at 1.4 V JTAG external clock rise and fall times TRST assert time Input setup times: Notes ns Input hold times: 4 ns 4 ns Valid times: Output hold times: 5 ns 5 ns 3 3 19 9 5, 6 Notes: 1.All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50-Ω load (see Figure 25). Time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2.The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K) going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals (D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 3.TRST is an asynchronous level sensitive signal. The setup time is for test purposes only. 4.Non-JTAG signal input timing with respect to tTCLK. 5.Non-JTAG signal output timing with respect to tTCLK. 6.Guaranteed by design. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 46 Freescale Semiconductor JTAG Figure 25 provides the AC test load for TDO and the boundary-scan outputs of the MPC8540. Z0 = 50 Ω Output RL = 50 Ω OVDD/2 Figure 25. AC Test Load for the JTAG Interface Figure 26 provides the JTAG clock input timing diagram. JTAG External Clock VM VM VM tJTGR tJTKHKL tJTGF tJTG VM = Midpoint Voltage (OVDD/2) Figure 26. JTAG Clock Input Timing Diagram Figure 27 provides the TRST timing diagram. TRST VM VM tTRST VM = Midpoint Voltage (OVDD/2) Figure 27. TRST Timing Diagram Figure 28 provides the boundary-scan timing diagram. JTAG External Clock VM VM tJTDVKH tJTDXKH Boundary Data Inputs Input Data Valid tJTKLDV tJTKLDX Boundary Data Outputs Output Data Valid tJTKLDZ Boundary Data Outputs Output Data Valid VM = Midpoint Voltage (OVDD/2) Figure 28. Boundary-Scan Timing Diagram MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 47 I2C Figure 29 provides the test access port timing diagram. JTAG External Clock VM VM tJTIVKH tJTIXKH Input Data Valid TDI, TMS tJTKLOV tJTKLOX TDO Output Data Valid tJTKLOZ TDO Output Data Valid VM = Midpoint Voltage (OVDD/2) Figure 29. Test Access Port Timing Diagram 11 I2C This section describes the DC and AC electrical characteristics for the I2C interface of the MPC8540. 11.1 I2C DC Electrical Characteristics Table 39 provides the DC electrical characteristics for the I2C interface of the MPC8540. Table 39. I2C DC Electrical Characteristics At recommended operating conditions with OVDD of 3.3 V ± 5%. Parameter Symbol Min Max Unit Input high voltage level VIH 0.7 × OVDD OVDD+ 0.3 V Input low voltage level VIL –0.3 0.3 × OVDD V Low level output voltage VOL 0 0.2 × OVDD V 1 tI2KHKL 0 50 ns 2 Input current each I/O pin (input voltage is between 0.1 × OVDD and 0.9 × OVDD(max) II –10 10 μA 3 Capacitance for each I/O pin CI — 10 pF Pulse width of spikes which must be suppressed by the input filter Notes Notes: 1.Output voltage (open drain or open collector) condition = 3 mA sink current. 2.Refer to the MPC8540 Integrated Processor Preliminary Reference Manual for information on the digital filter used. 3.I/O pins will obstruct the SDA and SCL lines if OVDD is switched off. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 48 Freescale Semiconductor I2C 11.2 I2C AC Electrical Specifications Table 40 provides the AC timing parameters for the I2C interface of the MPC8540. Table 40. I2C AC Electrical Specifications All values refer to VIH (min) and VIL (max) levels (see Table 39). Symbol 1 Min Max Unit fI2C 0 400 kHz Low period of the SCL clock tI2CL 6 1.3 — μs High period of the SCL clock tI2CH 6 0.6 — μs Setup time for a repeated START condition tI2SVKH 6 0.6 — μs Hold time (repeated) START condition (after this period, the first clock pulse is generated) tI2SXKL 6 0.6 — μs Data setup time tI2DVKH 6 100 — ns — 02 — 0.9 3 Parameter SCL clock frequency μs tI2DXKL Data hold time: CBUS compatible masters I2C bus devices Set-up time for STOP condition tI2PVKH 0.6 — μs Bus free time between a STOP and START condition tI2KHDX 1.3 — μs Noise margin at the LOW level for each connected device (including hysteresis) VNL 0.1 × OVDD — V Noise margin at the HIGH level for each connected device (including hysteresis) VNH 0.2 × OVDD — V Notes: 1.The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2) with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition (S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I2C timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2.MPC8540 provides a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the undefined region of the falling edge of SCL. 3.The maximum tI2DVKH has only to be met if the device does not stretch the LOW period (tI2CL) of the SCL signal. 4.CB = capacitance of one bus line in pF. 6.Guaranteed by design. Figure 18 provides the AC test load for the I2C. Output Z0 = 50 Ω RL = 50 Ω OVDD/2 Figure 30. I2C AC Test Load MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 49 PCI/PCI-X Figure 31 shows the AC timing diagram for the I2C bus. SDA tI2CF tI2DVKH tI2CL tI2KHKL tI2CF tI2SXKL tI2CR SCL tI2SXKL tI2CH tI2DXKL S tI2SVKH tI2PVKH Sr P S Figure 31. I2C Bus AC Timing Diagram 12 PCI/PCI-X This section describes the DC and AC electrical specifications for the PCI/PCI-X bus of the MPC8540. 12.1 PCI/PCI-X DC Electrical Characteristics Table 41 provides the DC electrical characteristics for the PCI/PCI-X interface of the MPC8540. Table 41. PCI/PCI-X DC Electrical Characteristics 1 Parameter Symbol Min Max Unit High-level input voltage VIH 2 OVDD + 0.3 V Low-level input voltage VIL –0.3 0.8 V Input current (VIN 2 = 0 V or VIN = VDD) IIN — ±5 μA High-level output voltage (OVDD = min, IOH = –100 μA) VOH OVDD – 0.2 — V Low-level output voltage (OVDD = min, IOL = 100 μA) VOL — 0.2 V Notes: 1.Ranges listed do not meet the full range of the DC specifications of the PCI 2.2 Local Bus Specifications. 2.Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 50 Freescale Semiconductor PCI/PCI-X 12.2 PCI/PCI-X AC Electrical Specifications This section describes the general AC timing parameters of the PCI/PCI-X bus of the MPC8540. Note that the SYSCLK signal is used as the PCI input clock. Table 42 provides the PCI AC timing specifications at 66 MHz. Table 42. PCI AC Timing Specifications at 66 MHz Symbol 1 Min Max Unit Notes SYSCLK to output valid tPCKHOV — 6.0 ns 2 Output hold from SYSCLK tPCKHOX 2.0 — ns 2, 9 SYSCLK to output high impedance tPCKHOZ — 14 ns 2, 3, 10 Input setup to SYSCLK tPCIVKH 3.0 — ns 2, 4, 9 Input hold from SYSCLK tPCIXKH 0 — ns 2, 4, 9 tPCRVRH 10 × tSYS — clocks 5, 6, 10 HRESET to REQ64 hold time tPCRHRX 0 50 ns 6, 10 HRESET high to first FRAME assertion tPCRHFV 10 — clocks 7, 10 Parameter REQ64 to HRESET 9 setup time Notes: 1.Note that the symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI/PCI-X timing (PC) with respect to the time the input signals (I) reach the valid state (V) relative to the SYSCLK clock, tSYS, reference (K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI/PCI-X timing (PC) with respect to the time hard reset (R) went high (H) relative to the frame signal (F) going to the valid (V) state. 2.See the timing measurement conditions in the PCI 2.2 Local Bus Specifications. 3.For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 4.Input timings are measured at the pin. 5.The timing parameter tSYS indicates the minimum and maximum CLK cycle times for the various specified frequencies. The system clock period must be kept within the minimum and maximum defined ranges. For values see Section 15, “Clocking.” 6.The setup and hold time is with respect to the rising edge of HRESET. 7.The timing parameter tPCRHFV is a minimum of 10 clocks rather than the minimum of 5 clocks in the PCI 2.2 Local Bus Specifications. 8.The reset assertion timing requirement for HRESET is 100 μs. 9.Guaranteed by characterization. 10.Guaranteed by design. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 51 PCI/PCI-X Figure 18 provides the AC test load for PCI and PCI-X. Z0 = 50 Ω Output RL = 50 Ω OVDD/2 Figure 32. PCI/PCI-X AC Test Load Figure 33 shows the PCI/PCI-X input AC timing conditions. CLK tPCIVKH tPCIXKH Input Figure 33. PCI-PCI-X Input AC Timing Measurement Conditions Figure 34 shows the PCI/PCI-X output AC timing conditions. CLK tPCKHOV Output Delay tPCKHOZ High-Impedance Output Figure 34. PCI-PCI-X Output AC Timing Measurement Condition Table 43 provides the PCI-X AC timing specifications at 66 MHz. Table 43. PCI-X AC Timing Specifications at 66 MHz Parameter Symbol Min Max Unit Notes SYSCLK to signal valid delay tPCKHOV — 3.8 ns 1, 2, 3, 7, 8 Output hold from SYSCLK tPCKHOX 0.7 — ns 1, 10 SYSCLK to output high impedance tPCKHOZ — 7 ns 1, 4, 8, 11 Input setup time to SYSCLK tPCIVKH 1.7 — ns 3, 5 Input hold time from SYSCLK tPCIXKH 0.5 — ns 10 REQ64 to HRESET setup time tPCRVRH 10 — clocks 11 HRESET to REQ64 hold time tPCRHRX 0 50 ns 11 HRESET high to first FRAME assertion tPCRHFV 10 — clocks 9, 11 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 52 Freescale Semiconductor PCI/PCI-X Table 43. PCI-X AC Timing Specifications at 66 MHz (continued) Parameter Symbol Min Max Unit Notes PCI-X initialization pattern to HRESET setup time tPCIVRH 10 — clocks 11 HRESET to PCI-X initialization pattern hold time tPCRHIX 0 50 ns 6, 11 Notes: 1.See the timing measurement conditions in the PCI-X 1.0a Specification. 2.Minimum times are measured at the package pin (not the test point). Maximum times are measured with the test point and load circuit. 3.Setup time for point-to-point signals applies to REQ and GNT only. All other signals are bused. 4.For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 5.Setup time applies only when the device is not driving the pin. Devices cannot drive and receive signals at the same time. 6.Maximum value is also limited by delay to the first transaction (time for HRESET high to first configuration access, tPCRHFV). The PCI-X initialization pattern control signals after the rising edge of HRESET must be negated no later than two clocks before the first FRAME and must be floated no later than one clock before FRAME is asserted. 7.A PCI-X device is permitted to have the minimum values shown for tPCKHOV and tCYC only in PCI-X mode. In conventional mode, the device must meet the requirements specified in PCI 2.2 for the appropriate clock frequency. 8.Device must meet this specification independent of how many outputs switch simultaneously. 9.The timing parameter tPCRHFV is a minimum of 10 clocks rather than the minimum of 5 clocks in the PCI-X 1.0a Specification. 10.Guaranteed by characterization. 11.Guaranteed by design. Table 44 provides the PCI-X AC timing specifications at 133 MHz. Table 44. PCI-X AC Timing Specifications at 133 MHz Parameter Symbol Min Max Unit Notes SYSCLK to signal valid delay tPCKHOV — 3.8 ns 1, 2, 3, 7, 8 Output hold from SYSCLK tPCKHOX 0.7 — ns 1, 11 SYSCLK to output high impedance tPCKHOZ — 7 ns 1, 4, 8, 12 Input setup time to SYSCLK tPCIVKH 1.4 — ns 3, 5, 9, 11 Input hold time from SYSCLK tPCIXKH 0.5 — ns 11 REQ64 to HRESET setup time tPCRVRH 10 — clocks 12 HRESET to REQ64 hold time tPCRHRX 0 50 ns 12 HRESET high to first FRAME assertion tPCRHFV 10 — clocks 10, 12 PCI-X initialization pattern to HRESET setup time tPCIVRH 10 — clocks 12 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 53 RapidIO Table 44. PCI-X AC Timing Specifications at 133 MHz (continued) Parameter HRESET to PCI-X initialization pattern hold time Symbol Min Max Unit Notes tPCRHIX 0 50 ns 6, 12 Notes: 1.See the timing measurement conditions in the PCI-X 1.0a Specification. 2.Minimum times are measured at the package pin (not the test point). Maximum times are measured with the test point and load circuit. 3.Setup time for point-to-point signals applies to REQ and GNT only. All other signals are bused. 4.For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 5.Setup time applies only when the device is not driving the pin. Devices cannot drive and receive signals at the same time. 6.Maximum value is also limited by delay to the first transaction (time for HRESET high to first configuration access, tPCRHFV). The PCI-X initialization pattern control signals after the rising edge of HRESET must be negated no later than two clocks before the first FRAME and must be floated no later than one clock before FRAME is asserted. 7.A PCI-X device is permitted to have the minimum values shown for tPCKHOV and tCYC only in PCI-X mode. In conventional mode, the device must meet the requirements specified in PCI 2.2 for the appropriate clock frequency. 8.Device must meet this specification independent of how many outputs switch simultaneously. 9.The timing parameter tPCIVKH is a minimum of 1.4 ns rather than the minimum of 1.2 ns in the PCI-X 1.0a Specification. 10.The timing parameter tPCRHFV is a minimum of 10 clocks rather than the minimum of 5 clocks in the PCI-X 1.0a Specification. 11.Guaranteed by characterization. 12.Guaranteed by design. 13 RapidIO This section describes the DC and AC electrical specifications for the RapidIO interface of the MPC8540. 13.1 RapidIO DC Electrical Characteristics RapidIO driver and receiver DC electrical characteristics are provided in Table 45 and Table 46, respectively. Table 45. RapidIO 8/16 LP-LVDS Driver DC Electrical Characteristics At recommended operating conditions with OVDD of 3.3 V ± 5%. Characteristic Symbol Min Max Unit Notes Differential output high voltage VOHD 247 454 mV 1, 2 Differential output low voltage VOLD –454 –247 mV 1, 2 Differential offset voltage ΔVOSD — 50 mV 1,3 Output high common mode voltage VOHCM 1.125 1.375 V 1, 4 Output low common mode voltage VOLCM 1.125 1.375 V 1, 5 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 54 Freescale Semiconductor RapidIO Table 45. RapidIO 8/16 LP-LVDS Driver DC Electrical Characteristics (continued) At recommended operating conditions with OVDD of 3.3 V ± 5%. Characteristic Symbol Min Max Unit Notes ΔVOSCM — 50 mV 1, 6 RTERM 90 220 W Short circuit current (either output) |ISS| — 24 mA 7 Bridged short circuit current |ISB| — 12 mA 8 Common mode offset voltage Differential termination Notes: 1.Bridged 100-Ω load. 2.See Figure 35(a). 3.Differential offset voltage = |VOHD+VOLD|. See Figure 35(b). 4.VOHCM = (VOA + VOB)/2 when measuring VOHD. 5.VOLCM = (VOA + VOB)/2 when measuring VOLD. 6.Common mode offset ΔVOSCM = |VOHCM – VOLCM|. See Figure 35(c). 7.Outputs shorted to VDD or GND. 8.Outputs shorted together. Table 46. RapidIO 8/16 LP-LVDS Receiver DC Electrical Characteristics Characteristic Symbol Min Max Unit VI 0 2.4 V Differential input high voltage VIHD 100 600 mV 1 Differential input low voltage VILD –600 –100 mV 1 Common mode input range (referenced to receiver ground) VICM 0.050 2.350 V 2 RIN 90 110 W Voltage at either input Input differential resistance Notes Notes: 1.Over the common mode range. 2.Limited by VI. See Figure 42. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 55 RapidIO Figure 35 shows the DC driver signal levels. VOA RTERM 100 Ω (no m) VOB V (a) VOD = VOA – VOB VOSCM = (VOA + VOB)/2 454 mV V VOD = VOA – VOB 1.375 V VOHCM ΔVOS 247 mV VOHD VOLCM –V + ΔVOD –V –247 mV –V – ΔVOD –454 mV VOLD 1.125 V 0 Differential Specifications Common-Mode Specifications (b) Note: VOA refers to voltage at output A; VOB refers to voltage at output B. (c) Figure 35. DC Driver Signal Levels 13.2 RapidIO AC Electrical Specifications This section contains the AC electrical specifications for a RapidIO 8/16 LP-LVDS device. The interface defined is a parallel differential low-power high-speed signal interface. Note that the source of the transmit clock on the RapidIO interface is dependent on the settings of the LGPL[0:1] signals at reset. Note that the default setting makes the core complex bus (CCB) clock the source of the transmit clock. See Chapter 4 of the Reference Manual for more details on reset configuration settings. 13.3 RapidIO Concepts and Definitions This section specifies signals using differential voltages. Figure 36 shows how the signals are defined. The figure shows waveforms for either a transmitter output (TD and TD) or a receiver input (RD and RD). Each signal swings between A volts and B volts where A > B. Using these waveforms, the definitions are as follows: • The transmitter output and receiver input signals TD, TD, RD, and RD each have a peak-to-peak swing of A-B volts. • The differential output signal of the transmitter, VOD, is defined as VTD – VTD. • The differential input signal of the receiver, VID, is defined as VRD – VRD. • The differential output signal of the transmitter or input signal of the receiver, ranges from A – B volts to – (A – B) volts. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 56 Freescale Semiconductor RapidIO • • The peak differential signal of the transmitter output or receiver input, is A – B volts. The peak-to-peak differential signal of the transmitter output or receiver input, is 2 × (A – B) volts. AV BV TD or RD TD or RD Figure 36. Differential Peak-to-Peak Voltage of Transmitter or Receiver To illustrate these definitions using numerical values, consider the case where a LVDS transmitter has a common mode voltage of 1.2 V and each signal has a swing that goes between 1.4 and 1.0 V. Using these values, the peak-to-peak voltage swing of the signals TD, TD, RD, and RD is 400 mV. The differential signal ranges between 400 and –400 mV. The peak differential signal is 400 mV, and the peak-to-peak differential signal is 800 mV. A timing edge is the zero-crossing of a differential signal. Each skew timing parameter on a parallel bus is synchronously measured on two signals relative to each other in the same cycle, such as data to data, data to clock, or clock to clock. A skew timing parameter may be relative to the edge of a signal or to the middle of two sequential edges. Static skew represents the timing difference between signals that does not vary over time regardless of system activity or data pattern. Path length differences are a primary source of static skew. Dynamic skew represents the amount of timing difference between signals that is dependent on the activity of other signals and varies over time. Crosstalk between signals is a source of dynamic skew. Eye diagrams and compliance masks are a useful way to visualize and specify driver and receiver performance. This technique is used in several serial bus specifications. An example compliance mask is shown in Figure 37. The key difference in the application of this technique for a parallel bus is that the data is source synchronous to its bus clock while serial data is referenced to its embedded clock. Eye diagrams reveal the quality (cleanness, openness, goodness) of a driver output or receiver input. An advantage of using an eye diagram and a compliance mask is that it allows specifying the quality of a signal without requiring separate specifications for effects such as rise time, duty cycle distortion, data dependent dynamic skew, random dynamic skew, etc. This allows the individual semiconductor manufacturer maximum flexibility to trade off various performance criteria while keeping the system performance constant. In using the eye pattern and compliance mask approach, the quality of the signal is specified by the compliance mask. The mask specifies the maximum permissible magnitude of the signal and the minimum permissible eye opening. The eye diagram for the signal under test is generated according to the specification. Compliance is determined by whether the compliance mask can be positioned over the eye diagram such that the eye pattern falls entirely within the unshaded portion of the mask. Serial specifications have clock encoded with the data, but the LP-LVDS physical layer defined by RapidIO is a source synchronous parallel port so additional specifications to include effects that are not found in serial links are required. Specifications for the effect of bit to bit timing differences caused by static skew have been added and the eye diagrams specified are measured relative to the associated clock in order to include clock to data effects. With the transmit output (or receiver input) eye diagram, the user can determine if the transmitter output (or receiver input) is compliant with an oscilloscope with the appropriate software. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 57 RapidIO Differential (V) Z Y 0 –Y DV –Z 0 X1 X2 Time (UI) 1–X2 1–X1 1 Figure 37. Example Compliance Mask Y = minimum data valid amplitude Z = maximum amplitude 1 UI = 1 unit interval = 1/baud rate X1 = end of zero crossing region X2 = beginning of data valid window DV = data valid window = 1 – 2 × X2 The waveform of the signal under test must fall within the unshaded area of the mask to be compliant. Different masks are used for the driver output and the receiver input allowing each to be separately specified. 13.3.1 RapidIO Driver AC Timing Specifications Driver AC timing specifications are provided in Table 47, Table 48, and Table 49. A driver shall comply with the specifications for each data rate/frequency for which operation of the driver is specified. Unless otherwise specified, these specifications are subject to the following conditions. • The specifications apply over the supply voltage and ambient temperature ranges specified by the device vendor. • The specifications apply for any combination of data patterns on the data signals. • The output of a driver shall be connected to a 100 Ω, ±1%, differential (bridged) resistive load. • Clock specifications apply only to clock signals. • Data specifications apply only to data signals (FRAME, D[0:7]). Table 47. RapidIO Driver AC Timing Specifications—500 Mbps Data Rate Range Characteristic Symbol Min Max Unit Notes Differential output high voltage VOHD 200 540 mV 1 Differential output low voltage VOLD –540 –200 mV 1 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 58 Freescale Semiconductor RapidIO Table 47. RapidIO Driver AC Timing Specifications—500 Mbps Data Rate (continued) Range Characteristic Symbol Unit Notes 52 % 2, 6 200 — ps 3, 6 tRISE 200 — ps 6 DV 1260 — ps tDPAIR — 180 ps 4, 6 tSKEW,PAIR –180 180 ps 5, 6 Min Max DC 48 VOD rise time, 20%–80% of peak-to-peak differential signal swing tFALL VOD fall time, 20%–80% of peak-to-peak differential signal swing Duty cycle Data valid Skew of any two data outputs Skew of single data outputs to associated clock Notes: 1.See Figure 38. 2.Requires ±100 ppm long term frequency stability. 3.Measured at VOD = 0 V. 4.Measured using the RapidIO transmit mask shown in Figure 38. 5.See Figure 43. 6.Guaranteed by design. Table 48. RapidIO Driver AC Timing Specifications—750 Mbps Data Rate Range Characteristic Symbol Min Max Unit Notes Differential output high voltage VOHD 200 540 mV 1 Differential output low voltage VOLD –540 –200 mV 1 DC 48 52 % 2, 6 VOD rise time, 20%–80% of peak-to-peak differential signal swing tFALL 133 — ps 3, 6 VOD fall time, 20%–80% of peak-to-peak differential signal swing tRISE 133 — ps 6 DV 800 — ps 6 tDPAIR — 133 ps 4, 6 tSKEW,PAIR –133 133 ps 5, 6 Duty cycle Data valid Skew of any two data outputs Skew of single data outputs to associated clock Notes: 1.See Figure 38. 2.Requires ±100 ppm long term frequency stability. 3.Measured at VOD = 0 V. 4.Measured using the RapidIO transmit mask shown in Figure 38. 5.See Figure 43. 6.Guaranteed by design. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 59 RapidIO Table 49. RapidIO Driver AC Timing Specifications—1 Gbps Data Rate Range Characteristic Symbol Min Max Unit Notes Differential output high voltage VOHD 200 540 mV 1 Differential output low voltage VOLD –540 –200 mV 1 DC 48 52 % 2, 6 VOD rise time, 20%–80% of peak to peak differential signal swing tFALL 100 — ps 3, 6 VOD fall time, 20%–80% of peak to peak differential signal swing tRISE 100 — ps 6 DV 575 — ps 6 tDPAIR — 100 ps 4, 6 tSKEW,PAIR –100 100 ps 5, 6 Duty cycle Data valid Skew of any two data outputs Skew of single data outputs to associated clock Notes: 1.See Figure 38. 2.Requires ±100 ppm long term frequency stability. 3.Measured at VOD = 0 V. 4.Measured using the RapidIO transmit mask shown in Figure 38. 5.See Figure 43. 6.Guaranteed by design. The compliance of driver output signals TD[0:15] and TFRAME with their minimum data valid window (DV) specification shall be determined by generating an eye pattern for each of the data signals and comparing the eye pattern of each data signal with the RapidIO transmit mask shown in Figure 38. The value of X2 used to construct the mask shall be (1 – DVmin)/2. A signal is compliant with the data valid window specification if the transmit mask can be positioned on the signal’s eye pattern such that the eye pattern falls entirely within the unshaded portion of the mask. VOHDmax VOD (mV) VOHDmin 0 VOLDmax DV VOLDmin 0 X2 Time (UI) 1–X2 1 Figure 38. RapidIO Transmit Mask MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 60 Freescale Semiconductor RapidIO The eye pattern for a data signal is generated by making a large number of recordings of the signal and then overlaying the recordings. The number of recordings used to generate the eye shall be large enough that further increasing the number of recordings used does not cause the resulting eye pattern to change from one that complies with the RapidIO transmit mask to one that does not. Each data signal in the interface shall be carrying random or pseudo-random data when the recordings are made. If pseudo-random data is used, the length of the pseudo-random sequence (repeat length) shall be long enough that increasing the length of the sequence does not cause the resulting eye pattern to change from one that complies with the RapidIO transmit mask to one that does not comply with the mask. The data carried by any given data signal in the interface may not be correlated with the data carried by any other data signal in the interface. The zero-crossings of the clock associated with a data signal shall be used as the timing reference for aligning the multiple recordings of the data signal when the recordings are overlaid. While the method used to make the recordings and overlay them to form the eye pattern is not specified, the method used shall be demonstrably equivalent to the following method. The signal under test is repeatedly recorded with a digital oscilloscope in infinite persistence mode. Each recording is triggered by a zero-crossing of the clock associated with the data signal under test. Roughly half of the recordings are triggered by positive-going clock zero-crossings and roughly half are triggered by negative-going clock zero-crossings. Each recording is at least 1.9 UI in length (to ensure that at least one complete eye is formed) and begins 0.5 UI before the trigger point (0.5 UI before the associated clock zero-crossing). Depending on the length of the individual recordings used to generate the eye pattern, one or more complete eyes will be formed. Regardless of the number of eyes, the eye whose center is immediately to the right of the trigger point is the eye used for compliance testing. An example of an eye pattern generated using the above method with recordings 3 UI in length is shown in Figure 39. In this example, there is no skew between the signal under test and the associated clock used to trigger the recordings. If skew was present, the eye pattern would be shifted to the left or right relative to the oscilloscope trigger point. . 0.5 UI 1.0 UI 1.0 UI VOD + 0 – Oscilloscope (Recording) Trigger Point Eye Used for Compliance Testing Eye Pattern Figure 39. Example Driver Output Eye Pattern MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 61 RapidIO 13.3.2 RapidIO Receiver AC Timing Specifications The RapidIO receiver AC timing specifications are provided in Table 50. A receiver shall comply with the specifications for each data rate/frequency for which operation of the receiver is specified. Unless otherwise specified, these specifications are subject to the following conditions. • The specifications apply over the supply voltage and ambient temperature ranges specified by the device vendor. • The specifications apply for any combination of data patterns on the data signals. • The specifications apply over the receiver common mode and differential input voltage ranges. • Clock specifications apply only to clock signals. • Data specifications apply only to data signals (FRAME, D[0:7]) Table 50. RapidIO Receiver AC Timing Specifications—500 Mbps Data Rate Range Characteristic Symbol Min Max 53 Unit Notes % 1, 5 ps 2 Duty cycle of the clock input DC 47 Data valid DV 1080 tDPAIR — 380 ps 3 tSKEW,PAIR –300 300 ps 4 Allowable static skew between any two data inputs within a 8-/9-bit group Allowable static skew of data inputs to associated clock Notes: 1.Measured at VID = 0 V. 2.Measured using the RapidIO receive mask shown in Figure 40. 3.See Figure 43. 4.See Figure 42 and Figure 43. 5.Guaranteed by design. Table 51. RapidIO Receiver AC Timing Specifications—750 Mbps Data Rate Range Characteristic Symbol Min Max Unit Notes Duty cycle of the clock input DC 47 53 % 1, 5 Data valid DV 600 — ps 2 tDPAIR — 400 ps 3 tSKEW,PAIR –267 267 ps 4 Allowable static skew between any two data inputs within a 8-/9-bit group Allowable static skew of data inputs to associated clock Notes: 1.Measured at VID = 0 V. 2.Measured using the RapidIO receive mask shown in Figure 40. 3.See Figure 43. 4.See Figure 42 and Figure 43. 5.Guaranteed by design. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 62 Freescale Semiconductor RapidIO Table 52. RapidIO Receiver AC Timing Specifications—1 Gbps Data Rate Range Characteristic Symbol Min Max Unit Notes Duty cycle of the clock input DC 47 53 % 1, 5 Data valid DV 425 — ps 2 tDPAIR — 300 ps 3 tSKEW,PAIR –200 200 ps 4 Allowable static skew between any two data inputs within a 8-/9-bit group Allowable static skew of data inputs to associated clock Notes: 1.Measured at VID = 0 V. 2.Measured using the RapidIO receive mask shown in Figure 40. 3.See Figure 43. 4.See Figure 42 and Figure 43. 5.Guaranteed by design. The compliance of receiver input signals RD[0:15] and RFRAME with their minimum data valid window (DV) specification shall be determined by generating an eye pattern for each of the data signals and comparing the eye pattern of each data signal with the RapidIO receive mask shown in Figure 40. The value of X2 used to construct the mask shall be (1 – DVmin)/2. The ±100 mV minimum data valid and ±600 mV maximum input voltage values are from the DC specification. A signal is compliant with the data valid window specification if and only if the receive mask can be positioned on the signal’s eye pattern such that the eye pattern falls entirely within the unshaded portion of the mask. 600 VID (mV) 100 0 –100 DV –600 0 X2 Time (UI) 1–X2 1 Figure 40. RapidIO Receive Mask The eye pattern for a data signal is generated by making a large number of recordings of the signal and then overlaying the recordings. The number of recordings used to generate the eye shall be large enough that further increasing the number of recordings used does not cause the resulting eye pattern to change from one that complies with the RapidIO receive mask to one that does not. Each data signal in the interface shall be carrying random or pseudo-random data when the recordings are made. If pseudo-random data is used, the length of the pseudo-random sequence (repeat length) shall be long MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 63 RapidIO enough that increasing the length of the sequence does not cause the resulting eye pattern to change from one that complies with the RapidIO receive mask to one that does not comply with the mask. The data carried by any given data signal in the interface may not be correlated with the data carried by any other data signal in the interface. The zero-crossings of the clock associated with a data signal shall be used as the timing reference for aligning the multiple recordings of the data signal when the recordings are overlaid. While the method used to make the recordings and overlay them to form the eye pattern is not specified, the method used shall be demonstrably equivalent to the following method. The signal under test is repeatedly recorded with a digital oscilloscope in infinite persistence mode. Each recording is triggered by a zero-crossing of the clock associated with the data signal under test. Roughly half of the recordings are triggered by positive-going clock zero-crossings and roughly half are triggered by negative-going clock zero-crossings. Each recording is at least 1.9 UI in length (to ensure that at least one complete eye is formed) and begins 0.5 UI before the trigger point (0.5 UI before the associated clock zero-crossing). Depending on the length of the individual recordings used to generate the eye pattern, one or more complete eyes will be formed. Regardless of the number of eyes, the eye whose center is immediately to the right of the trigger point is the eye used for compliance testing. An example of an eye pattern generated using the above method with recordings 3 UI in length is shown in Figure 41. In this example, there is no skew between the signal under test and the associated clock used to trigger the recordings. If skew was present, the eye pattern would be shifted to the left or right relative to the oscilloscope trigger point. 0.5 UI 1.0 UI 1.0 UI VID + 0 – Oscilloscope (Recording) Trigger Point Eye Used for Compliance Testing Eye Pattern Figure 41. Example Receiver Input Eye Pattern MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 64 Freescale Semiconductor RapidIO Figure 42 shows the definitions of the data to clock static skew parameter tSKEW,PAIR and the data valid window parameter DV. The data and frame bits are those that are associated with the clock. The figure applies for all zero-crossings of the clock. All of the signals are differential signals. VD represents VOD for the transmitter and VID for the receiver. The center of the eye is defined as the midpoint of the region in which the magnitude of the signal voltage is greater than or equal to the minimum DV voltage. VD = 0 V VD Clock x 1.0 UI Nominal 0.5 UI VD Clock x VD = 0 V tSKEW,PAIR 0.5 DV D[0:7]/D[8:15], FRAME 0.5 DV VHDmim Eye Opening VHDmim DV Figure 42. Data to Clock Skew Figure 43 shows the definition of the data to data static skew parameter tDPAIR and how the skew parameters are applied. Center Point for Clock 1.0 UI Nominal 0.5 UI CLK0 (CLK1) Center point of the data valid window of the earliest allowed data bit for data grouped late with respect to clock Center point of the data valid window of the latest allowed data bit for data grouped late with respect to clock D[0:7]/D[8:15], FRAME tDPAIR tSKEW,PAIR Figure 43. Static Skew Diagram MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 65 Package and Pin Listings 14 Package and Pin Listings This section details package parameters, pin assignments, and dimensions. 14.1 Package Parameters for the MPC8540 FC-PBGA The package parameters are as provided in the following list. The package type is 29 mm × 29 mm, 783 flip chip plastic ball grid array (FC-PBGA). Die size 12.2 mm × 9.5 mm Package outline 29 mm × 29 mm Interconnects 783 Pitch 1 mm Minimum module height 3.07 mm Maximum module height 3.75 mm Solder Balls 62 Sn/36 Pb/2 Ag Ball diameter (typical) 0.5 mm MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 66 Freescale Semiconductor Package and Pin Listings 14.2 Mechanical Dimensions of the MPC8540 FC-PBGA Figure 44 the mechanical dimensions and bottom surface nomenclature of the MPC8540, 783 FC-PBGA package. Figure 44. Mechanical Dimensions and Bottom Surface Nomenclature of the MPC8540 FC-PBGA NOTES 1. All dimensions are in millimeters. 2. Dimensions and tolerances per ASME Y14.5M-1994. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 67 Package and Pin Listings 3. 4. 5. 6. 7. Maximum solder ball diameter measured parallel to datum A. Datum A, the seating plane, is defined by the spherical crowns of the solder balls. Capacitors may not be present on all devices. Caution must be taken not to short capacitors or exposed metal capacitor pads on package top. The socket lid must always be oriented to A1. 14.3 Pinout Listings Table 53 provides the pin-out listing for the MPC8540, 783 FC-PBGA package. Table 53. MPC8540 Pinout Listing Signal Package Pin Number Pin Type Power Supply Notes PCI/PCI-X PCI_AD[63:0] AA14, AB14, AC14, AD14, AE14, AF14, AG14, AH14, V15, W15, Y15, AA15, AB15, AC15, AD15, AG15, AH15, V16, W16, AB16, AC16, AD16, AE16, AF16, V17, W17, Y17, AA17, AB17, AE17, AF17, AF18, AH6, AD7, AE7, AH7, AB8, AC8, AF8, AG8, AD9, AE9, AF9, AG9, AH9, W10, Y10, AA10, AE11, AF11, AG11, AH11, V12, W12, Y12, AB12, AD12, AE12, AG12, AH12, V13, Y13, AB13, AC13 I/O OVDD 17 PCI_C_BE[7:0] AG13, AH13, V14, W14, AH8, AB10, AD11, AC12 I/O OVDD 17 PCI_PAR AA11 I/O OVDD PCI_PAR64 Y14 I/O OVDD PCI_FRAME AC10 I/O OVDD 2 PCI_TRDY AG10 I/O OVDD 2 PCI_IRDY AD10 I/O OVDD 2 PCI_STOP V11 I/O OVDD 2 PCI_DEVSEL AH10 I/O OVDD 2 PCI_IDSEL AA9 I OVDD PCI_REQ64 AE13 I/O OVDD 5, 10 PCI_ACK64 AD13 I/O OVDD 2 PCI_PERR W11 I/O OVDD 2 PCI_SERR Y11 I/O OVDD 2, 4 PCI_REQ0 AF5 I/O OVDD PCI_REQ[1:4] AF3, AE4, AG4, AE5 I OVDD PCI_GNT[0] AE6 I/O OVDD PCI_GNT[1:4] AG5, AH5, AF6, AG6 O OVDD 5, 9 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 68 Freescale Semiconductor Package and Pin Listings Table 53. MPC8540 Pinout Listing (continued) Signal Package Pin Number Pin Type Power Supply Notes DDR SDRAM Memory Interface MDQ[0:63] M26, L27, L22, K24, M24, M23, K27, K26, K22, J28, F26, E27, J26, J23, H26, G26, C26, E25, C24, E23, D26, C25, A24, D23, B23, F22, J21, G21, G22, D22, H21, E21, N18, J18, D18, L17, M18, L18, C18, A18, K17, K16, C16, B16, G17, L16, A16, L15, G15, E15, C14, K13, C15, D15, E14, D14, D13, E13, D12, A11, F13, H13, A13, B12 I/O GVDD MECC[0:7] N20, M20, L19, E19, C21, A21, G19, A19 I/O GVDD MDM[0:8] L24, H28, F24, L21, E18, E16, G14, B13, M19 O GVDD MDQS[0:8] L26, J25, D25, A22, H18, F16, F14, C13, C20 I/O GVDD MBA[0:1] B18, B19 O GVDD MA[0:14] N19, B21, F21, K21, M21, C23, A23, B24, H23, G24, K19, B25, D27, J14, J13 O GVDD MWE D17 O GVDD MRAS F17 O GVDD MCAS J16 O GVDD MCS[0:3] H16, G16, J15, H15 O GVDD MCKE[0:1] E26, E28 O GVDD MCK[0:5] J20, H25, A15, D20, F28, K14 O GVDD MCK[0:5] F20, G27, B15, E20, F27, L14 O GVDD MSYNC_IN M28 I GVDD MSYNC_OUT N28 O GVDD 11 Local Bus Controller Interface LA[27] U18 O OVDD 5, 9 LA[28:31] T18, T19, T20, T21 O OVDD 7, 9 LAD[0:31] AD26, AD27, AD28, AC26, AC27, AC28, AA22, AA23, AA26, Y21, Y22, Y26, W20, W22, W26, V19, T22, R24, R23, R22, R21, R18, P26, P25, P20, P19, P18, N22, N23, N24, N25, N26 I/O OVDD LALE V21 O OVDD 8, 9 LBCTL V20 O OVDD 9 LCKE U23 O OVDD LCLK[0:2] U27, U28, V18 O OVDD LCS[0:4] Y27, Y28, W27, W28, R27 O OVDD 18 LCS5/DMA_DREQ2 R28 I/O OVDD 1 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 69 Package and Pin Listings Table 53. MPC8540 Pinout Listing (continued) Signal Package Pin Number Pin Type Power Supply Notes LCS6/DMA_DACK2 P27 O OVDD 1 LCS7/DMA_DDONE2 P28 O OVDD 1 LDP[0:3] AA27, AA28, T26, P21 I/O OVDD LGPL0/LSDA10 U19 O OVDD 5, 9 LGPL1/LSDWE U22 O OVDD 5, 9 LGPL2/LOE/LSDRAS V28 O OVDD 8, 9 LGPL3/LSDCAS V27 O OVDD 5, 9 LGPL4/LGTA/LUPWAIT/ LPBSE V23 I/O OVDD 22 LGPL5 V22 O OVDD 5, 9 LSYNC_IN T27 I OVDD LSYNC_OUT T28 O OVDD LWE[0:1]/LSDDQM[0:1]/LBS AB28, AB27 [0:1] O OVDD 1, 5, 9 LWE[2:3]/LSDDQM[2:3]/LBS T23, P24 [2:3] O OVDD 1, 5, 9 DMA DMA_DREQ[0:1] H5, G4 I OVDD DMA_DACK[0:1] H6, G5 O OVDD DMA_DDONE[0:1] H7, G6 O OVDD DUART UART_SIN[0:1] AE2, AD5 I OVDD UART_SOUT[0:1] AE3, AD2 O OVDD UART_CTS[0:1] U9, U7 I OVDD UART_RTS[0:1] AD6, AD1 O OVDD Programmable Interrupt Controller MCP AG17 I OVDD UDE AG16 I OVDD IRQ[0:7] AA18, Y18, AB18, AG24, AA21, Y19, AA19, AG25 I OVDD IRQ8 AB20 I OVDD 9 IRQ9/DMA_DREQ3 Y20 I OVDD 1 IRQ10/DMA_DACK3 AF26 I/O OVDD 1 IRQ11/DMA_DDONE3 AH24 I/O OVDD 1 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 70 Freescale Semiconductor Package and Pin Listings Table 53. MPC8540 Pinout Listing (continued) Signal IRQ_OUT Package Pin Number Pin Type Power Supply Notes O OVDD 2, 4 5, 9 AB21 Ethernet Management Interface EC_MDC F1 O OVDD EC_MDIO E1 I/O OVDD I LVDD Gigabit Reference Clock EC_GTX_CLK125 E2 Three-Speed Ethernet Controller (Gigabit Ethernet 1) TSEC1_TXD[7:4] A6, F7, D7, C7 O LVDD 5, 9 TSEC1_TXD[3:0] B7, A7, G8, E8 O LVDD 9, 19 TSEC1_TX_EN C8 O LVDD 11 TSEC1_TX_ER B8 O LVDD TSEC1_TX_CLK C6 I LVDD TSEC1_GTX_CLK B6 O LVDD TSEC1_CRS C3 I LVDD TSEC1_COL G7 I LVDD TSEC1_RXD[7:0] D4, B4, D3, D5, B5, A5, F6, E6 I LVDD TSEC1_RX_DV D2 I LVDD TSEC1_RX_ER E5 I LVDD TSEC1_RX_CLK D6 I LVDD 18 Three-Speed Ethernet Controller (Gigabit Ethernet 2) TSEC2_TXD[7:2] B10, A10, J10, K11,J11, H11 O LVDD TSEC2_TXD[1:0] G11, E11 O LVDD TSEC2_TX_EN B11 O LVDD TSEC2_TX_ER D11 O LVDD TSEC2_TX_CLK D10 I LVDD TSEC2_GTX_CLK C10 O LVDD TSEC2_CRS D9 I LVDD TSEC2_COL F8 I LVDD TSEC2_RXD[7:0] F9, E9, C9, B9, A9, H9, G10, F10 I LVDD TSEC2_RX_DV H8 I LVDD TSEC2_RX_ER A8 I LVDD 5, 9 11 18 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 71 Package and Pin Listings Table 53. MPC8540 Pinout Listing (continued) Signal TSEC2_RX_CLK Package Pin Number E10 Pin Type Power Supply I LVDD Notes 10/100 Ethernet (MII) Interface FEC_TXD[3:0] M1, N1, N4, N5 O OVDD FEC_TX_EN P11 O OVDD FEC_TX_ER P10 O OVDD FEC_TX_CLK V6 I OVDD FEC_CRS N10 I OVDD FEC_COL N11 I OVDD FEC_RXD[3:0] N9, N8, N7, N6 I OVDD FEC_RX_DV P8 I OVDD FEC_RX_ER P9 I OVDD FEC_RX_CLK V9 I OVDD RapidIO Interface RIO_RCLK Y25 I OVDD RIO_RCLK Y24 I OVDD RIO_RD[0:7] T25, U25, V25, W25, AA25, AB25, AC25, AD25 I OVDD RIO_RD[0:7] T24, U24, V24, W24, AA24, AB24, AC24, AD24 I OVDD RIO_RFRAME AE27 I OVDD RIO_RFRAME AE26 I OVDD RIO_TCLK AC20 O OVDD 11 RIO_TCLK AE21 O OVDD 11 RIO_TD[0:7] AE18, AC18, AD19, AE20, AD21, AE22, AC22, AD23 O OVDD RIO_TD[0:7] AD18, AE19, AC19, AD20, AC21, AD22, AE23, AC23 O OVDD RIO_TFRAME AE24 O OVDD RIO_TFRAME AE25 O OVDD RIO_TX_CLK_IN AF24 I OVDD RIO_TX_CLK_IN AF25 I OVDD I2C interface IIC_SDA AH22 I/O OVDD 4, 20 IIC_SCL AH23 I/O OVDD 4, 20 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 72 Freescale Semiconductor Package and Pin Listings Table 53. MPC8540 Pinout Listing (continued) Signal Package Pin Number Pin Type Power Supply Notes System Control HRESET AH16 I OVDD HRESET_REQ AG20 O OVDD SRESET AF20 I OVDD CKSTP_IN M11 I OVDD CKSTP_OUT G1 O OVDD 2, 4 Debug TRIG_IN N12 I OVDD TRIG_OUT/READY G2 O OVDD 6, 9, 19 MSRCID[0:1] J9, G3 O OVDD 5, 6, 9 MSRCID[2:4] F3, F5, F2 O OVDD 6 MDVAL F4 O OVDD 6 Clock SYSCLK AH21 I OVDD RTC AB23 I OVDD CLK_OUT AF22 O OVDD 11 JTAG TCK AF21 I OVDD TDI AG21 I OVDD 12 TDO AF19 O OVDD 11 TMS AF23 I OVDD 12 TRST AG23 I OVDD 12 DFT LSSD_MODE AG19 I OVDD 21 L1_TSTCLK AB22 I OVDD 21 L2_TSTCLK AG22 I OVDD 21 TEST_SEL AH20 I OVDD 3 Thermal Management THERM0 AG2 I — 14 THERM1 AH3 I — 14 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 73 Package and Pin Listings Table 53. MPC8540 Pinout Listing (continued) Signal Package Pin Number Power Supply Pin Type Notes Power Management ASLEEP AG18 I/O 9, 19 Power and Ground Signals AVDD1 AH19 Power for e500 PLL (1.2 V) AVDD1 AVDD2 AH18 Power for CCB PLL (1.2 V) AVDD2 GND A12, A17, B3, B14, B20, B26, B27, C2, C4, C11,C17, C19, C22, C27, D8, E3, E12, E24, F11, F18, F23, G9, G12, G25, H4, H12, H14, H17, H20, H22, H27, J19, J24, K5, K9, K18, K23, K28, L6, L20, L25, M4, M12, M14, M16, M22, M27, N2, N13, N15, N17, P12, P14, P16, P23, R13, R15, R17, R20, R26, T3, T8, T10, T12, T14, T16, U6, U13, U15, U16, U17, U21, V7, V10, V26, W5, W18, W23, Y8, Y16, AA6, AA13, AB4, AB11, AB19, AC6, AC9, AD3, AD8, AD17, AF2, AF4, AF10, AF13, AF15, AF27, AG3, AG7, AG26 — — GVDD A14, A20, A25, A26, A27, A28, B17, B22, B28, C12, C28, D16, D19, D21, D24, D28, E17, E22, F12, F15, F19, F25, G13, G18, G20, G23, G28, H19, H24, J12, J17, J22, J27, K15, K20, K25, L13, L23, L28, M25, N21 Power for DDR DRAM I/O Voltage (2.5 V) GVDD LVDD A4, C5, E7, H10 Reference Voltage; Three-Speed Ethernet I/O (2.5 V, 3.3 V) LVDD MVREF N27 Reference Voltage Signal; DDR MVREF No Connects AH26, AH27, AH28, AG28, AF28, AE28, AH1, AG1, AH2, B1, B2, A2, A3, AH25, H1, H2, J1, J2, J3, J4, J5, J6, J7, J8, K8, K7, K6, K3, K2, K1, L1, L2, L3, L4, L5, L8, L9, L10, L11, M10, M9, M8, M7, M6, M3, M2, P7, P6, P5, P4, P3, P2, P1, R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, T9, T6, T5, T4, T1, U1, U2, U3, U4, U8, U10, V5, V4, V3, V2, V1, W1, W2, W3, W6, W7, W8, W9, Y1, Y2, Y3, Y4, Y5, Y6, Y9, AA8, AA7, AA4, AA3, AA2, AA1, AB1, AB2, AB3, AB5, AB6, AC7, AC4, AC3, AC2, AC1 — — OVDD D1, E4, H3, K4, K10, L7, M5, N3, P22, R19, R25, PCI/PCI-X, T2, T7, U5, U20, U26, V8, W4, W13, W19, W21, Y7, RapidIO, 10/100 Y23, AA5, AA12, AA16, AA20, AB7, AB9, AB26, Ethernet, and other AC5, AC11, AC17, AD4, AE1, AE8, AE10, AE15, Standard AF7, AF12, AG27, AH4 (3.3 V) 16 OVDD MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 74 Freescale Semiconductor Package and Pin Listings Table 53. MPC8540 Pinout Listing (continued) Signal Package Pin Number Pin Type Power Supply Notes — — 15 RESERVED C1, T11, U11, AF1 SENSEVDD L12 Power for Core (1.2 V) VDD 13 SENSEVSS K12 — — 13 VDD M13, M15, M17, N14, N16, P13, P15, P17, R12, R14, R16, T13, T15, T17, U12, U14, AH17 Power for Core (1.2 V) VDD Notes: 1.All multiplexed signals are listed only once and do not re-occur. For example, LCS5/DMA_REQ2 is listed only once in the Local Bus Controller Interface section, and is not mentioned in the DMA section even though the pin also functions as DMA_REQ2. 2.Recommend a weak pull-up resistor (2–10 kΩ) be placed on this pin to OVDD. 3.This pin must always be tied to GND. . 4.This pin is an open drain signal. 5.This pin is a reset configuration pin. It has a weak internal pull-up P-FET which is enabled only when the MPC8540 is in the reset state. This pull-up is designed such that it can be overpowered by an external 4.7-kΩ pull-down resistor. If an external device connected to this pin might pull it down during reset, then a pull-up or active driver is needed if the signal is intended to be high during reset. 6.Treat these pins as no connects (NC) unless using debug address functionality. 7.The value of LA[28:31] during reset sets the CCB clock to SYSCLK PLL ratio. These pins require 4.7-kΩ pull-up or pull-down resistors. See Section 15.2, “Platform/System PLL Ratio.” 8.The value of LALE and LGPL2 at reset set the e500 core clock to CCB Clock PLL ratio. These pins require 4.7-kΩ pull-up or pull-down resistors. See the Section 15.3, “e500 Core PLL Ratio.” 9.Functionally, this pin is an output, but structurally it is an I/O because it either samples configuration input during reset or because it has other manufacturing test functions. This pin will therefore be described as an I/O for boundary scan. 10.This pin functionally requires a pull-up resistor, but during reset it is a configuration input that controls 32- vs. 64-bit PCI operation. Therefore, it must be actively driven low during reset by reset logic if the device is to be configured to be a 64-bit PCI device. Refer to the PCI Specification. 11.This output is actively driven during reset rather than being three-stated during reset. 12.These JTAG pins have weak internal pull-up P-FETs that are always enabled. 13.These pins are connected to the VDD/GND planes internally and may be used by the core power supply to improve tracking and regulation. 14.Internal thermally sensitive resistor. 15.No connections should be made to these pins. 16.These pins are not connected for any functional use. 17.PCI specifications recommend that a weak pull-up resistor (2–10 kΩ) be placed on the higher order pins to OVDD when using 64-bit buffer mode (pins PCI_AD[63:32] and PCI_C_BE[7:4]). 18.Note that these signals are POR configurations for Rev. 1.x and notes 5 and 9 apply to these signals in Rev. 1.x but not in later revisions. 19 If this pin is connected to a device that pulls down during reset, an external pull-up is required to drive this pin to a logic –1 state during reset. 20.Recommend a pull-up resistor (~1 KΩ) b placed on this pin to OVDD. 21.These are test signals for factory use only and must be pulled up (100 Ω - 1 kΩ) to OVDD for normal machine operation. 22.If this signal is used as both an input and an output, a weak pull-up (~10 kΩ) is required on this pin. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 75 Clocking 15 Clocking This section describes the PLL configuration of the MPC8540. Note that the platform clock is identical to the CCB clock. 15.1 Clock Ranges Table 54 provides the clocking specifications for the processor core and Table 55 provides the clocking specifications for the memory bus. Table 54. Processor Core Clocking Specifications Maximum Processor Core Frequency Characteristic 667 MHz e500 core processor frequency 833 MHz 1 GHz Min Max Min Max Min Max 400 667 400 833 400 1000 Unit Notes MHz 1, 2, 3 Notes: 1.Caution: The CCB to SYSCLK ratio and e500 core to CCB ratio settings must be chosen such that the resulting SYSCLK frequency, e500 (core) frequency, and CCB frequency do not exceed their respective maximum or minimum operating frequencies. Refer to Section 15.2, “Platform/System PLL Ratio,” and Section 15.3, “e500 Core PLL Ratio,” for ratio settings. 2.)The minimum e500 core frequency is based on the minimum platform frequency of 200 MHz. 3.)The 1.0 GHz core frequency is based on a 1.3 V VDD supply voltage. Table 55. Memory Bus Clocking Specifications Maximum Processor Core Frequency Characteristic Memory bus frequency 667 MHz 833 MHz 1 GHz Min Max Min Max Min Max 100 166 100 166 100 166 Unit Notes MHz 1, 2, 3 Notes: 1.Caution: The CCB to SYSCLK ratio and e500 core to CCB ratio settings must be chosen such that the resulting SYSCLK frequency, e500 (core) frequency, and CCB frequency do not exceed their respective maximum or minimum operating frequencies. Refer to Section 15.2, “Platform/System PLL Ratio,” and Section 15.3, “e500 Core PLL Ratio,” for ratio settings. 2.The memory bus speed is half of the DDR data rate, hence, half of the platform clock frequency. 3.)The 1.0 GHz core frequency is based on a 1.3 V VDD supply voltage. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 76 Freescale Semiconductor Clocking 15.2 Platform/System PLL Ratio The platform clock is the clock that drives the L2 cache, the DDR SDRAM data rate, and the e500 core complex bus (CCB), and is also called the CCB clock. The values are determined by the binary value on LA[28:31] at power up, as shown in Table 56. There is no default for this PLL ratio; these signals must be pulled to the desired values. Table 56. CCB Clock Ratio Binary Value of LA[28:31] Signals Ratio Description 0000 16:1 ratio CCB clock: SYSCLK (PCI bus) 0001 Reserved 0010 2:1 ratio CCB clock: SYSCLK (PCI bus) 0011 3:1 ratio CCB clock: SYSCLK (PCI bus) 0100 4:1 ratio CCB clock: SYSCLK (PCI bus) 0101 5:1 ratio CCB clock: SYSCLK (PCI bus) 0110 6:1 ratio CCB clock: SYSCLK (PCI bus) 0111 Reserved 1000 8:1 ratio CCB clock: SYSCLK (PCI bus) 1001 9:1 ratio CCB clock: SYSCLK (PCI bus) 1010 10:1 ratio CCB clock: SYSCLK (PCI bus) 1011 Reserved 1100 12:1 ratio CCB clock: SYSCLK (PCI bus) 1101 Reserved 1110 Reserved 1111 Reserved 15.3 e500 Core PLL Ratio Table 57 describes the clock ratio between the e500 core complex bus (CCB) and the e500 core clock. This ratio is determined by the binary value of LALE and LGPL2 at power up, as shown in Table 57. Table 57. e500 Core to CCB Ratio Binary Value of LALE, LGPL2 Signals Ratio Description 00 2:1 e500 core:CCB 01 5:2 e500 core:CCB 10 3:1 e500 core:CCB 11 7:2 e500 core:CCB MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 77 Thermal 15.4 Frequency Options Table 58 shows the expected frequency values for the platform frequency when using a CCB to SYSCLK ratio in comparison to the memory bus speed. Table 58. Frequency Options with Respect to Memory Bus Speeds CCB to SYSCLK Ratio SYSCLK (MHz) 16.67 25 33.33 41.63 66.67 83 100 111 133.33 200 222 267 300 333 Platform/CCB Frequency (MHz) 2 3 200 250 4 267 333 5 208 6 200 250 333 8 200 267 9 225 300 10 250 333 12 200 16 267 333 300 16 Thermal This section describes the thermal specifications of the MPC8540. 16.1 Thermal Characteristics Table 59 provides the package thermal characteristics for the MPC8540. Table 59. Package Thermal Characteristics Characteristic Symbol Value Unit Notes Junction-to-ambient Natural Convection on four layer board (2s2p) RθJMA 16 °C/W 1, 2 Junction-to-ambient (@100 ft/min or 0.5 m/s) on four layer board (2s2p) RθJMA 14 °C/W 1, 2 Junction-to-ambient (@200 ft/min or 1 m/s) on four layer board (2s2p) RθJMA 12 •C/W 1, 2 RθJB 7.5 •C/W 3 Junction-to-board thermal MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 78 Freescale Semiconductor Thermal Table 59. Package Thermal Characteristics (continued) Characteristic Junction-to-case thermal Symbol Value Unit Notes RθJC 0.8 •C/W 4 Notes 1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance 2. Per JEDEC JESD51-6 with the board horizontal. 3. Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 4. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1). Cold plate temperature is used for case temperature; measured value includes the thermal resistance of the interface layer. 16.2 Thermal Management Information This section provides thermal management information for the flip chip plastic ball grid array (FC-PBGA) package for air-cooled applications. Proper thermal control design is primarily dependent on the system-level design—the heat sink, airflow, and thermal interface material. The recommended attachment method to the heat sink is illustrated in Figure 45. The heat sink should be attached to the printed-circuit board with the spring force centered over the die. This spring force should not exceed 10 pounds force. FC-PBGA Package Heat Sink Heat Sink Clip Adhesive or Thermal Interface Material Lid Die Printed-Circuit Board Figure 45. Package Exploded Cross-Sectional View with Several Heat Sink Options The system board designer can choose between several types of heat sinks to place on the MPC8540. There are several commercially-available heat sinks from the following vendors: Aavid Thermalloy 80 Commercial St. Concord, NH 03301 Internet: www.aavidthermalloy.com 603-224-9988 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 79 Thermal Alpha Novatech 473 Sapena Ct. #15 Santa Clara, CA 95054 Internet: www.alphanovatech.com 408-749-7601 International Electronic Research Corporation (IERC) 413 North Moss St. Burbank, CA 91502 Internet: www.ctscorp.com 818-842-7277 Millennium Electronics (MEI) Loroco Sites 671 East Brokaw Road San Jose, CA 95112 Internet: www.mei-millennium.com 408-436-8770 Tyco Electronics Chip Coolers™ P.O. Box 3668 Harrisburg, PA 17105-3668 Internet: www.chipcoolers.com 800-522-6752 Wakefield Engineering 33 Bridge St. Pelham, NH 03076 Internet: www.wakefield.com 603-635-5102 Ultimately, the final selection of an appropriate heat sink depends on many factors, such as thermal performance at a given air velocity, spatial volume, mass, attachment method, assembly, and cost. Several heat sinks offered by Aavid Thermalloy, Alpha Novatech, IERC, Chip Coolers, Millennium Electronics, and Wakefield Engineering offer different heat sink-to-ambient thermal resistances, that will allow the MPC8540 to function in various environments. 16.2.1 Recommended Thermal Model For system thermal modeling, the MPC8540 thermal model is shown in Figure 46. Five cuboids are used to represent this device. To simplify the model, the solder balls and substrate are modeled as a single block 29x29x1.47 mm with the conductivity adjusted accordingly. For modeling, the planar dimensions of the die are rounded to the nearest mm, so the die is modeled as 10x12 mm at a thickness of 0.76 mm. The bump/underfill layer is modeled as a collapsed resistance between the die and substrate assuming a conductivity of 0.6 in-plane and 1.9 W/m•K in the thickness dimension of 0.76 mm. The lid attach adhesive is also modeled as a collapsed resistance with dimensions of 10x12x0.050 mm and the conductivity of 1 W/m•K. The nickel plated copper lid is modeled as 12x14x1 mm. Note that the die and lid are not centered on the substrate; there is a 1.5 mm offset documented in the case outline drawing in Figure 44. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 80 Freescale Semiconductor Thermal Conductivity Value Unit Lid (12 × 14 × 1 mm) kx 360 ky 360 kz 360 W/(m × K) 1 ky 1 kz 1 Die z Bump/underfill Substrate and solder balls Lid Adhesive—Collapsed resistance (10 × 12 × 0.050 mm) kx Adhesive Lid Side View of Model (Not to Scale) x Die (10 × 12 × 0.76 mm) Substrate Bump/Underfill—Collapsed resistance (10 × 12 × 0.070 mm) kx 0.6 ky 0.6 kz 1.9 Heat Source Substrate and Solder Balls (29 × 29 × 1.47 mm) kx 10.2 ky 10.2 kz 1.6 y Top View of Model (Not to Scale) Figure 46. MPC8540 Thermal Model 16.2.2 Internal Package Conduction Resistance For the packaging technology, shown in Table 59, the intrinsic internal conduction thermal resistance paths are as follows: • The die junction-to-case thermal resistance • The die junction-to-board thermal resistance MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 81 Thermal Figure 47 depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit board. External Resistance Radiation Convection Heat Sink Thermal Interface Material Die/Package Die Junction Package/Leads Internal Resistance Printed-Circuit Board External Resistance Radiation Convection (Note the internal versus external package resistance) Figure 47. Package with Heat Sink Mounted to a Printed-Circuit Board The heat sink removes most of the heat from the device. Heat generated on the active side of the chip is conducted through the silicon and through the lid, then through the heat sink attach material (or thermal interface material), and finally to the heat sink. The junction-to-case thermal resistance is low enough that the heat sink attach material and heat sink thermal resistance are the dominant terms. 16.2.3 Thermal Interface Materials A thermal interface material is required at the package-to-heat sink interface to minimize the thermal contact resistance. For those applications where the heat sink is attached by spring clip mechanism, Figure 48 shows the thermal performance of three thin-sheet thermal-interface materials (silicone, graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function of contact pressure. As shown, the performance of these thermal interface materials improves with increasing contact pressure. The use of thermal grease significantly reduces the interface thermal resistance. The bare joint results in a thermal resistance approximately six times greater than the thermal grease joint. Heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see Figure 45). Therefore, the synthetic grease offers the best thermal performance, especially at the low interface pressure. When removing the heat sink for re-work, it is preferable to slide the heat sink off slowly until the thermal interface material loses its grip. If the support fixture around the package prevents sliding off the heat sink, the heat sink should be slowly removed. Heating the heat sink to 40-50•C with an air gun can soften the interface material and make the removal easier. The use of an adhesive for heat sink attach is not recommended. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 82 Freescale Semiconductor Thermal Silicone Sheet (0.006 in.) Bare Joint Floroether Oil Sheet (0.007 in.) Graphite/Oil Sheet (0.005 in.) Synthetic Grease Specific Thermal Resistance (K-in.2/W) 2 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 Contact Pressure (psi) Figure 48. Thermal Performance of Select Thermal Interface Materials The system board designer can choose between several types of thermal interface. There are several commercially-available thermal interfaces provided by the following vendors: Chomerics, Inc. 77 Dragon Ct. Woburn, MA 01888-4014 Internet: www.chomerics.com 781-935-4850 Dow-Corning Corporation Dow-Corning Electronic Materials 2200 W. Salzburg Rd. Midland, MI 48686-0997 Internet: www.dowcorning.com 800-248-2481 Shin-Etsu MicroSi, Inc. 10028 S. 51st St. Phoenix, AZ 85044 Internet: www.microsi.com 888-642-7674 The Bergquist Company 18930 West 78th St. Chanhassen, MN 55317 Internet: www.bergquistcompany.com 800-347-4572 MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 83 Thermal Thermagon Inc. 4707 Detroit Ave. Cleveland, OH 44102 Internet: www.thermagon.com 888-246-9050 16.2.4 Heat Sink Selection Examples The following section provides a heat sink selection example using one of the commercially available heat sinks. 16.2.4.1 Case 1 For preliminary heat sink sizing, the die-junction temperature can be expressed as follows: TJ = TI + TR + (θJC + θINT + θSA) × PD where TJ is the die-junction temperature TI is the inlet cabinet ambient temperature TR is the air temperature rise within the computer cabinet θJC is the junction-to-case thermal resistance θINT is the adhesive or interface material thermal resistance θSA is the heat sink base-to-ambient thermal resistance PD is the power dissipated by the device During operation the die-junction temperatures (TJ) should be maintained within the range specified in Table 2. The temperature of air cooling the component greatly depends on the ambient inlet air temperature and the air temperature rise within the electronic cabinet. An electronic cabinet inlet-air temperature (TA) may range from 30° to 40°C. The air temperature rise within a cabinet (TR) may be in the range of 5° to 10°C. The thermal resistance of some thermal interface material (θINT) may be about 1°C/W. Assuming a TI of 30 C, a TR of 5 C, a FC-PBGA package θJC = 0.8, and a power consumption (PD) of 7.0 W, the following expression for TJ is obtained: Die-junction temperature: TJ = 30°C + 5°C + (0.8°C/W + 1.0°C/W + θSA) × 7.0 W The heat sink-to-ambient thermal resistance (θSA) versus airflow velocity for a Thermalloy heat sink #2328B is shown in Figure 49. Assuming an air velocity of 2 m/s, we have an effective θSA+ of about 3.3 C/W, thus TJ = 30 C + 5 C + (0.8 C/W +1.0 C/W + 3.3 C/W) × 7.0 W, resulting in a die-junction temperature of approximately 71 C which is well within the maximum operating temperature of the component. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 84 Freescale Semiconductor Thermal 8 Thermalloy #2328B Pin-fin Heat Sink (25 × 28 × 15 mm) Heat Sink Thermal Resistance (°C/W) 7 6 5 4 3 2 1 0 0.5 1 1.5 2 2.5 3 3.5 Approach Air Velocity (m/s) Figure 49. Thermalloy #2328B Heat Sink-to-Ambient Thermal Resistance Versus Airflow Velocity 16.2.4.2 Case 2 Every system application has different conditions that the thermal management solution must solve. As an alternate example, assume that the air reaching the component is 85 C with an approach velocity of 1 m/sec. For a maximum junction temperature of 105 C at 7 W, the total thermal resistance of junction to case thermal resistance plus thermal interface material plus heat sink thermal resistance must be less than 2.8 C/W. The value of the junction to case thermal resistance in Table 59 includes the thermal interface resistance of a thin layer of thermal grease as documented in footnote 4 of the table. Assuming that the heat sink is flat enough to allow a thin layer of grease or phase change material, then the heat sink must be less than 2 C/W. Millennium Electronics (MEI) has tooled a heat sink MTHERM-1051 for this requirement assuming a compactPCI environment at 1 m/sec and a heat sink height of 12 mm. The MEI solution is illustrated in Figure 50 and Figure 51. This design has several significant advantages: • The heat sink is clipped to a plastic frame attached to the application board with screws or plastic inserts at the corners away from the primary signal routing areas. • The heat sink clip is designed to apply the force holding the heat sink in place directly above the die at a maximum force of less than 10 lbs. • For applications with significant vibration requirements, silicone damping material can be applied between the heat sink and plastic frame. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 85 Thermal The spring mounting should be designed to apply the force only directly above the die. By localizing the force, rocking of the heat sink is minimized. One suggested mounting method attaches a plastic fence to the board to provide the structure on which the heat sink spring clips. The plastic fence also provides the opportunity to minimize the holes in the printed-circuit board and to locate them at the corners of the package. Figure 50 and Figure 51 provide exploded views of the plastic fence, heat sink, and spring clip. Figure 50. Exploded Views (1) of a Heat Sink Attachment using a Plastic Force MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 86 Freescale Semiconductor Thermal Figure 51. Exploded Views (2) of a Heat Sink Attachment using a Plastic Fence The die junction-to-ambient and the heat sink-to-ambient thermal resistances are common figure-of-merits used for comparing the thermal performance of various microelectronic packaging technologies, one should exercise caution when only using this metric in determining thermal management because no single parameter can adequately describe three-dimensional heat flow. The final die-junction operating temperature is not only a function of the component-level thermal resistance, but the system level design and its operating conditions. In addition to the component’s power consumption, a number of factors affect the final operating die-junction temperature: airflow, board population (local heat flux of adjacent components), system air temperature rise, altitude, etc. Due to the complexity and the many variations of system-level boundary conditions for today’s microelectronic equipment, the combined effects of the heat transfer mechanisms (radiation convection and conduction) may vary widely. For these reasons, we recommend using conjugate heat transfer models for the boards, as well as, system-level designs. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 87 System Design Information 17 System Design Information This section provides electrical and thermal design recommendations for successful application of the MPC8540. 17.1 System Clocking The MPC8540includes two PLLs. 1. The platform PLL generates the platform clock from the externally supplied SYSCLK input. The frequency ratio between the platform and SYSCLK is selected using the platform PLL ratio configuration bits as described in Section 15.2, “Platform/System PLL Ratio.” 2. The e500 Core PLL generates the core clock as a slave to the platform clock. The frequency ratio between the e500 core clock and the platform clock is selected using the e500 PLL ratio configuration bits as described in Section 15.3, “e500 Core PLL Ratio.” 17.2 PLL Power Supply Filtering Each of the PLLs listed above is provided with power through independent power supply pins (AVDD1 and AVDD2, respectively). The AVDD level should always be equivalent to VDD, and preferably these voltages will be derived directly from VDD through a low frequency filter scheme such as the following. There are a number of ways to reliably provide power to the PLLs, but the recommended solution is to provide three independent filter circuits as illustrated in Figure 52, one to each of the three AVDD pins. By providing independent filters to each PLL the opportunity to cause noise injection from one PLL to the other is reduced. This circuit is intended to filter noise in the PLLs resonant frequency range from a 500 kHz to 10 MHz range. It should be built with surface mount capacitors with minimum Effective Series Inductance (ESL). Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a single large value capacitor. Each circuit should be placed as close as possible to the specific AVDD pin being supplied to minimize noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AVDD pin, which is on the periphery of the 783 FC-PBGA footprint, without the inductance of vias. Figure 52 shows the PLL power supply filter circuit. 10 Ω VDD AVDD (or L2AVDD) 2.2 µF 2.2 µF GND Low ESL Surface Mount Capacitors Figure 52. PLL Power Supply Filter Circuit MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 88 Freescale Semiconductor System Design Information 17.3 Decoupling Recommendations Due to large address and data buses, and high operating frequencies, the MPC8540 can generate transient power surges and high frequency noise in its power supply, especially while driving large capacitive loads. This noise must be prevented from reaching other components in the MPC8540 system, and the MPC8540 itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system designer place at least one decoupling capacitor at each VDD, OVDD, GVDD, and LVDD pins of the MPC8540. These decoupling capacitors should receive their power from separate VDD, OVDD, GVDD, LVDD, and GND power planes in the PCB, utilizing short traces to minimize inductance. Capacitors may be placed directly under the device using a standard escape pattern. Others may surround the part. These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic SMT (surface mount technology) capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes. In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB, feeding the VDD, OVDD, GVDD, and LVDD planes, to enable quick recharging of the smaller chip capacitors. These bulk capacitors should have a low ESR (equivalent series resistance) rating to ensure the quick response time necessary. They should also be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk capacitors—100–330 µF (AVX TPS tantalum or Sanyo OSCON). 17.4 Connection Recommendations To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level. Unused active low inputs should be tied to OVDD, GVDD, or LVDD as required. Unused active high inputs should be connected to GND. All NC (no-connect) signals must remain unconnected. Power and ground connections must be made to all external VDD, GVDD, LVDD, OVDD, and GND pins of the MPC8540. 17.5 Output Buffer DC Impedance The MPC8540 drivers are characterized over process, voltage, and temperature. There are two driver types: a push-pull single-ended driver (open drain for I2C) for all buses except RapidIO, and a current-steering differential driver for the RapidIO port. To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD or GND. Then, the value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 53). The output impedance is the average of two components, the resistances of the pull-up and pull-down devices. When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals OVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 89 System Design Information OVDD RN SW2 Pad Data SW1 RP OGND Figure 53. Driver Impedance Measurement The output impedance of the RapidIO port drivers targets 200-Ω differential resistance. The value of this resistance and the strength of the driver’s current source can be found by making two measurements. First, the output voltage is measured while driving logic 1 without an external differential termination resistor. The measured voltage is V1 = Rsource × Isource. Second, the output voltage is measured while driving logic 1 with an external precision differential termination resistor of value Rterm. The measured voltage is V2 = 1/(1/R1 + 1/R2)) × Isource. Solving for the output impedance gives Rsource = Rterm × (V1/V2 – 1). The drive current is then Isource = V1/Rsource. Table 60 summarizes the signal impedance targets. The driver impedance are targeted at minimum VDD, nominal OVDD, 105°C. Table 60. Impedance Characteristics Impedance Local Bus, Ethernet, DUART, Control, Configuration, Power Management PCI/PCI-X DDR DRAM RapidIO Symbol Unit RN 43 Target 25 Target 20 Target NA Z0 W RP 43 Target 25 Target 20 Target NA Z0 W Differential NA NA NA 200 Target ZDIFF W Note: Nominal supply voltages. See Table 1, Tj = 105°C. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 90 Freescale Semiconductor System Design Information 17.6 Configuration Pin Muxing The MPC8540 provides the user with power-on configuration options which can be set through the use of external pull-up or pull-down resistors of 4.7 kΩ on certain output pins (see customer visible configuration pins). These pins are generally used as output only pins in normal operation. While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins while HRESET is asserted, is latched when HRESET deasserts, at which time the input receiver is disabled and the I/O circuit takes on its normal function. Most of these sampled configuration pins are equipped with an on-chip gated resistor of approximately 20 kΩ. This value should permit the 4.7-kΩ resistor to pull the configuration pin to a valid logic low level. The pull-up resistor is enabled only during HRESET (and for platform/system clocks after HRESET deassertion to ensure capture of the reset value). When the input receiver is disabled the pull-up is also, thus allowing functional operation of the pin as an output with minimal signal quality or delay disruption. The default value for all configuration bits treated this way has been encoded such that a high voltage level puts the device into the default state and external resistors are needed only when non-default settings are required by the user. Careful board layout with stubless connections to these pull-down resistors coupled with the large value of the pull-down resistor should minimize the disruption of signal quality or speed for output pins thus configured. The platform PLL ratio and e500 PLL ratio configuration pins are not equipped with these default pull-up devices. 17.7 Pull-Up Resistor Requirements The MPC8540 requires high resistance pull-up resistors (10 kΩ is recommended) on open drain type pins including EPIC interrupt pins. I2C open drain type pins should be pulled up with ~1 kΩ resistors. Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 55. Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most have asynchronous behavior and spurious assertion will give unpredictable results. TSEC1_TXD[3:0] must not be pulled low during reset. Some PHY chips have internal pulldowns that could cause this to happen. If such PHY chips are used, then a pullup must be placed on these signals strong enough to restore these signals to a logical 1 during reset. Three test pins also require pull-up resistors (100 Ω - 1 kΩ). These pins are L1_TSTCLK, L2_TSTCLK, and LSSD_MODE. These signals are for factory use only and must be pulled up to OVDD for normal machine operation. Refer to the PCI 2.2 specification for all pull-ups required for PCI. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 91 System Design Information 17.8 JTAG Configuration Signals Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the IEEE Std 1149.1 specification, but is provided on all processors that implement the Power Architecture. The device requires TRST to be asserted during reset conditions to ensure the JTAG boundary logic does not interfere with normal chip operation. While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, generally systems will assert TRST during the power-on reset flow. Simply tying TRST to HRESET is not practical because the JTAG interface is also used for accessing the common on-chip processor (COP) function. The COP function of these processors allow a remote computer system (typically, a PC with dedicated hardware and debugging software) to access and control the internal operations of the processor. The COP interface connects primarily through the JTAG port of the processor, with some additional status monitoring signals. The COP port requires the ability to independently assert HRESET or TRST in order to fully control the processor. If the target system has independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must be merged into these signals with logic. The arrangement shown in Figure 54 allows the COP port to independently assert HRESET or TRST, while ensuring that the target can drive HRESET as well. The COP interface has a standard header, shown in Figure 54, for connection to the target system, and is based on the 0.025" square-post, 0.100" centered header assembly (often called a Berg header). The connector typically has pin 14 removed as a connector key. The COP header adds many benefits such as breakpoints, watchpoints, register and memory examination/modification, and other standard debugger features. An inexpensive option can be to leave the COP header unpopulated until needed. There is no standardized way to number the COP header; consequently, many different pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in Figure 54 is common to all known emulators. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 92 Freescale Semiconductor System Design Information COP_TDO 1 2 NC COP_TDI 3 4 COP_TRST NC 5 6 COP_VDD_SENSE COP_TCK 7 8 COP_CHKSTP_IN COP_TMS 9 10 NC COP_SRESET 11 12 NC COP_HRESET 13 KEY No pin COP_CHKSTP_OUT 15 16 GND Figure 54. COP Connector Physical Pinout 17.8.1 Termination of Unused Signals If the JTAG interface and COP header will not be used, Freescale recommends the following connections: • TRST should be tied to HRESET through a 0 kΩ isolation resistor so that it is asserted when the system reset signal (HRESET) is asserted, ensuring that the JTAG scan chain is initialized during the power-on reset flow. Freescale recommends that the COP header be designed into the system as shown in Figure 55. If this is not possible, the isolation resistor will allow future access to TRST in case a JTAG interface may need to be wired onto the system in future debug situations. • Tie TCK to OVDD through a 10 kΩ resistor. This will prevent TCK from changing state and reading incorrect data into the device. • No connection is required for TDI, TMS, or TDO. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 93 System Design Information OVDD SRESET From Target Board Sources (if any) HRESET 13 11 10 kΩ SRESET 6 10 kΩ HRESET1 COP_HRESET 10 kΩ COP_SRESET 10 kΩ 5 10 kΩ 10 kΩ 2 3 4 5 6 7 8 9 10 11 12 KEY 13 No pin 15 6 5 COP Header 1 4 15 COP_TRST COP_VDD_SENSE2 10 Ω NC COP_CHKSTP_OUT CKSTP_OUT 10 kΩ 14 3 10 kΩ COP_CHKSTP_IN CKSTP_IN 8 COP_TMS 16 9 COP Connector Physical Pinout TRST1 1 3 TMS COP_TDO TDO COP_TDI TDI COP_TCK 7 TCK 2 NC 10 NC 12 4 10 kΩ 16 Notes: 1. The COP port and target board should be able to independently assert HRESET and TRST to the processor in order to fully control the processor as shown here. 2. Populate this with a 10 Ω resistor for short-circuit/current-limiting protection. 3. The KEY location (pin 14) is not physically present on the COP header. 4. Although pin 12 is defined as a No-Connect, some debug tools may use pin 12 as an additional GND pin for improved signal integrity. 5. This switch is included as a precaution for BSDL testing. The switch should be open during BSDL testing to avoid accidentally asserting the TRST line. If BSDL testing is not being performed, this switch should be closed or removed. 6. Asserting SRESET causes a machine check interrupt to the e500 core. Figure 55. JTAG Interface Connection MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 94 Freescale Semiconductor Document Revision History 18 Document Revision History Table 61 provides a revision history for this hardware specification. Table 61. Document Revision History Rev. No. 4.1 Substantive Change(s) Inserted Figure 3 and paragraph above it. Added PCI/PCI-X row to Input Voltage characteristic and added footnote 6 to Table 1. 4 Updated Note in Section 2.1.2, “Power Sequencing.” Updated back page information. 3.5 Updated Section 2.1.2, “Power Sequencing.” Replaced Section 17.8, “JTAG Configuration Signals.” 3.4 Corrected MVREF Max Value in Table 1. Corrected MVREF Max Value in Table 2. Added new revision level information to Table 62 3.3 Updated MVREF Max Value in Table 1. Removed Figure 3. In Table 4, replaced TBD with power numbers and added footnote. Updated specs and footnotes in Table 8. Corrected max number for MVREF in Table 13. Changed parameter “Clock cycle duration” to “Clock period” in Table 29. Added note 4 to tLBKHOV1 and removed LALE reference from tLBKHOV3 in Table 36 and Table 37. Updated LALE signal in Figure 19 and Figure 20. Modified Figure 23. Modified Figure 55. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 95 Document Revision History Table 61. Document Revision History (continued) Rev. No. Substantive Change(s) 3.2 Updated Table 1 and Table 2 with 1.0 GHz device parameter requirements. Added Section 2.1.2, “Power Sequencing”. Updated Table 4 with Maximum power data. Updated Table 4 and Table 5 with 1 GHz speed grade information. Updated Table 6 with corrected typical I/O power numbers. Updated Table 7 Note 2 lower voltage measurement point. Replaced Table 7 Note 5 with spread spectrum clocking guidelines. Added to Table 8 rise and fall time information. Added Section 4.4, “Real Time Clock Timing”. Added precharge information to Section 6.2.2, “DDR SDRAM Output AC Timing Specifications”. Updated Table 20 minimum and maximum baud rates. Removed VIL and VIH references from Table 23, Table 24, Table 25, and Table 26. Added reference level note to Table 23, Table 24, Table 25, Table 26, Table 27, Table 28, and Table 29. Updated TXD references to TCG in Section 8.2.3.1, “TBI Transmit AC Timing Specifications”. Updated PMA_RX_CLK references to RX_CLK in Section 8.2.3.2, “TBI Receive AC Timing Specifications”. Updated tTTKHDX value in Table 27. Updated RXD references to RCG in Section 8.2.3.2, “TBI Receive AC Timing Specifications”. Updated Table 29 Note 2. Removed VIL and VIH references from Table 31, and Table 32. Added reference level note to Table 31, and Table 32. Corrected Figure 15 and Figure 16. Corrected Table 34 fMDC and tMDC to reflect the correct minimum operating frequency. Updated Table 34 tMDKHDV and tMDKHDX values for clarification. Added tLBKHKT and updated Note 2 in Table 37. Corrected LGTA timing references in Figure 19. Updated Figure 20, Figure 22, and Figure 24. Updated Figure 44. Clarified Table 53 Note 5. Updated Table 54 and Table 55 with 1 GHz information. Added heat sink removal discussion to Section 16.2.3, “Thermal Interface Materials”. Corrected and added 1 GHz part number to Table 62. 3.1 Updated Table 4 and Table 5. Added Table 6. Added MCK duty cycle to Table 16. Updated fMDC, tMDC, tMDKHDV, and tMDKHDX parameters in Table 34. Added LALE to tLBKHOV3 parameter in Table 36 and Table 37, and updated Figure 19 and Figure 20. Corrected active level designations of some of the pins in Table 53. Updated Table 62. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 96 Freescale Semiconductor Document Revision History Table 61. Document Revision History (continued) Rev. No. 3.0 Substantive Change(s) Table 1—Corrected MII management voltage reference Section 2.1.3—New Table 2—Corrected MII management voltage reference Table 4—Added VDD power table Table 5—Added AVDD power table Table 7—New Table 8—New Table 9—New Table 13—Added overshoot/undershoot note. Figure 4—New Table 16—Restated tMCKSKEW1 as tMCKSKEW, removed tMCKSKEW2; added speed-specific minimum values for 333, 266, and 200 MHz; updated tDDSHME values. Updated chapter to reflect that GMII, MII and TBI can be run with 2.5V signalling. Table 34—Added MDIO output valid timing Table 36—Updated tLBIVKH1, tLBIXKH1, and tLBOTOT. Table 37—New Table 20, Table 22, Table 24—Updated clock reference Table 44—Updated tPCIVKH Section 14.1— Changed minimum height from 2.22 to 3.07 and maximum from 2.76 to 3.75 Table 53.—Updated MII management voltage reference and added note 20. Section 16.2.4.1—Changed θJC from 0.3 to 0.8; changed die-junction temperature from 67 to 71 Section 17.7—Added paragraph that begins “TSEC1_TXD[3:0]...” MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 97 Document Revision History Table 61. Document Revision History (continued) Rev. No. 2.0 Substantive Change(s) Section 1.1—Updated features list to coincide with latest version of the reference manual Table 1 and Table 2—Addition of SYSCLK to OVIN Table 2—Addition of notes 1 and 2 Table 3—Addition of note 1 Table 5—New Section 4—New Table 13—Addition of IVREF Removed Figure 4 DDR SRAM Input TIming Diagram Table 15—Modified maximum values for tDISKEW Table 16—Added MSYNC_OUT to tMCKSKEW2 Figure 5—New Section 6.2.1—Removed Figure 4, “DDR SDRAM Input Timing Diagram” Section 8.1—Removed references to 2.5 V from first paragraph Figure 8—New Table 21 and Table 22—Modified “conditions” for IIH and I IL Table 23—Addition of min and max for GTX_CLK125 reference clock duty cycle Table 27 —Addition of min and max for GTX_CLK125 reference clock duty cycle Table 29—Addition of min and max for GTX_CLK125 reference clock duty cycle Table 30—VOH min and conditions; IIH and I IL conditions Table 31—Min and max for tMTXR and tMTXF Table 32—Min and max for tMRXR and tMRXF Figure 23 and Figure 24—Changed LSYNC_IN to Internal clock at top of each figure Figure 18—New Figure 18—New Table 36—Removed row for tLBKHOX3 Table 43—New (AC timing of PCI-X at 66 MHz) Table 53—Addition of note 19 Figure 55—Addition of jumper and note at top of diagram Table 55: Changed max bus freq for 667 core to 166 Section 16.2.1—Modified first paragraph Figure 46—Modified Figure 47—New Table 59—Modified thermal resistance data Section 16.2.4.2—Modified first and second paragraphs MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 98 Freescale Semiconductor Document Revision History Table 61. Document Revision History (continued) Rev. No. Substantive Change(s) 1.2 Section 1.1.1—Updated feature list. Section 1.2.1.1—Updated notes for Table 1. Section 1.2.1.2—Removed 5-V PCI interface overshoot and undershoot figure. Section 1.2.1.3—Added this section to summarize impedance driver settings for various interfaces. Section 1.4—Updated rows in Reset Initialization timing specifications table. Added a table with DLL and PLL timing specifications. Section 1.5.2.2—Updated note 6 of DDR SDRAM Output AC Timing Specifications table. Section 1.7—Changed the minimum input low current from -600 to -15 μA for the RGMII DC electrical characteristics. Section 1.8.2—Changed LCS[3:4] to TSEC1_TXD[6:5] in. Updated notes regarding LCS[3:4]. Section 1.13.2—Updated the mechanical dimensions diagram for the package. Section 1.13.3—Updated the notes for LBCTL, TRIG_OUT, and ASLEEP. Corrected pin assignments for IIC_SDA and IIC_SCL. Corrected reserved pin assignment of V11 to U11. V11 is actually PCI_STOP. Section 1.14.1—Updated the table for frequency options with respect to platform/CCB frequencies. Section 1.14.4—Edited Frequency options with respect to memory bus speeds. 1.1 Section 1.6.1—Added symbols and note for the GTX_CLK125 timing parameters. Section 1.11.3—Updated pin list table: LGPL5/LSDAMUX to LGPL5, LA[27:29] and LA[30:31] to LA[27:31], FEC_TXD[0:3] to FEC_TXD[3:0], FEC_RXD[0:3] to FEC_RXD[3:0], TRST to TRST, added GBE Clocking section and EC_GTX_CLK125 signal. Updated thermal model information to match current offering. 1 Original Customer Version. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 99 Device Nomenclature 19 Device Nomenclature Ordering information for the parts fully covered by this specification document is provided in Section 19.1, “Nomenclature of Parts Fully Addressed by this Document.” 19.1 Nomenclature of Parts Fully Addressed by this Document Table 62 provides the Freescale part numbering nomenclature for the MPC8540. Note that the individual part numbers correspond to a maximum processor core frequency. For available frequencies, contact your local Freescale sales office. In addition to the processor frequency, the part numbering scheme also includes an application modifier which may specify special application conditions. Each part number also contains a revision code which refers to the die mask revision number. Table 62. Part Numbering Nomenclature MPC nnnn t pp ff(f) c r Product Code Part Identifier Temperature Range1 Package 2 Processor Frequency 3, 4 Platform Frequency Revision Level MPC 8540 Blank = 0 to 105°C C = –40 to 105°C PX = FC-PBGA 833 = 833 MHz VT = FC-PBGA 667 = 667 MHz (Pb-free) L = 333 MHz J = 266 MHz B = Rev. 2.0 (SVR = 0x80300020) C = Rev. 2.1 (SVR = 0x80300021) MPC 8540 Blank = 0 to 105°C C = –40 to 105°C PX = FC-PBGA AQ = 1.0 GHz VT = FC-PBGA (Pb-free) F = 333 MHz B = Rev. 2.0 (SVR = 0x80300020) C = Rev. 2.1 (SVR = 0x80300021) Notes: 1.For Temperature Range=C, Processor Frequency is limited to 667 MHz. 2.See Section 14, “Package and Pin Listings,” for more information on available package types. 3.Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this specification support all core frequencies. The core must be clocked at a minimum frequency of 400MHz. A device must not be used beyond the core frequency or platform frequency indicated on the device. 4.Designers should use the maximum power value corresponding to the core and platform frequency grades indicated on the device. A lower maximum power value should not be assumed for design purposes even when running at a lower frequency. MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 100 Freescale Semiconductor Device Nomenclature 19.2 Part Marking Parts are marked as the example shown in Figure 56. MPCnnnntppfffcr MPC85nn ATWLYYWWA xPXxxxn MMMMM ATWLYYWWA MMMMM CCCCC CCCCC YWWLAZ 85xx FC-PBGA Notes: MMMMM is the 5-digit mask number. ATWLYYWWA is the traceability code. CCCCC is the country of assembly. This space is left blank if parts are assembled in the United States. YWWLAZ is the assembly traceability code. Figure 56. Part Marking for FC-PBGA Device MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 101 Device Nomenclature THIS PAGE INTENTIONALLY LEFT BLANK MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 102 Freescale Semiconductor Device Nomenclature THIS PAGE INTENTIONALLY LEFT BLANK MPC8540 Integrated Processor Hardware Specifications, Rev. 4.1 Freescale Semiconductor 103 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com under its patent rights nor the rights of others. Freescale Semiconductor products are Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com claims, costs, damages, and expenses, and reasonable attorney fees arising out of, For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 +1-800 441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor @hibbertgroup.com Document Number: MPC8540EC Rev. 4.1 07/2007 not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. The described product is a PowerPC microprocessor. The PowerPC name is a trademark of IBM Corp. and is used under license. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc., 2004-2007. All rights reserved.