Freescale Semiconductor
Technical Data
Document Number: MRF7S19210H
Rev. 1, 3/2011
RF Power Field Effect Transistors
N--Channel Enhancement--Mode Lateral MOSFETs
MRF7S19210HR3
MRF7S19210HSR3
Designed for CDMA base station applications with frequencies from 1930 to
1990 MHz. Can be used in Class AB and Class C for all typical cellular base
station modulation formats.
• Typical Single--Carrier W--CDMA Performance: VDD = 28 Volts, IDQ =
1400 mA, Pout = 63 Watts Avg., f = 1987.5 MHz, IQ Magnitude Clipping,
Channel Bandwidth = 3.84 MHz, Input Signal PAR = 7.5 dB @ 0.01%
Probability on CCDF.
Power Gain — 20 dB
Drain Efficiency — 29%
Device Output Signal PAR — 5.9 dB @ 0.01% Probability on CCDF
ACPR @ 5 MHz Offset — --33 dBc in 3.84 MHz Channel Bandwidth
• Capable of Handling 5:1 VSWR, @ 32 Vdc, 1960 MHz, 190 Watts CW
Output Power (3 dB Input Overdrive from Rated Pout)
• Typical Pout @ 1 dB Compression Point ≃ 190 Watts CW
Features
• 100% PAR Tested for Guaranteed Output Power Capability
• Characterized with Series Equivalent Large--Signal Impedance Parameters
• Internally Matched for Ease of Use
• Integrated ESD Protection
• Greater Negative Gate--Source Voltage Range for Improved Class C
Operation
• Designed for Digital Predistortion Error Correction Systems
• RoHS Compliant
• In Tape and Reel. R3 Suffix = 250 Units, 56 mm Tape Width, 13 inch Reel.
1930--1990 MHz, 63 W AVG., 28 V
SINGLE W--CDMA
LATERAL N--CHANNEL
RF POWER MOSFETs
CASE 465--06, STYLE 1
NI--780
MRF7S19210HR3
CASE 465A--06, STYLE 1
NI--780S
MRF7S19210HSR3
Table 1. Maximum Ratings
Rating
Symbol
Value
Unit
Drain--Source Voltage
VDSS
--0.5, +65
Vdc
Gate--Source Voltage
VGS
--6.0, +10
Vdc
Operating Voltage
VDD
32, +0
Vdc
Storage Temperature Range
Tstg
--65 to +150
°C
Case Operating Temperature
TC
150
°C
Operating Junction Temperature (1,2)
TJ
225
°C
Symbol
Value (2,3)
Unit
Table 2. Thermal Characteristics
Characteristic
Thermal Resistance, Junction to Case
Case Temperature 85°C, 190 W CW
Case Temperature 79°C, 63 W CW
RθJC
0.34
0.38
°C/W
1. Continuous use at maximum temperature will affect MTTF.
2. MTTF calculator available at http://www.freescale.com/rf. Select Software & Tools/Development Tools/Calculators to access MTTF
calculators by product.
3. Refer to AN1955, Thermal Measurement Methodology of RF Power Amplifiers. Go to http://www.freescale.com/rf.
Select Documentation/Application Notes -- AN1955.
© Freescale Semiconductor, Inc., 2008, 2011. All rights reserved.
RF Device Data
Freescale Semiconductor
MRF7S19210HR3 MRF7S19210HSR3
1
Table 3. ESD Protection Characteristics
Test Methodology
Class
Human Body Model (per JESD22--A114)
1C (Minimum)
Machine Model (per EIA/JESD22--A115)
A (Minimum)
Charge Device Model (per JESD22--C101)
IV (Minimum)
Table 4. Electrical Characteristics (TA = 25°C unless otherwise noted)
Symbol
Min
Typ
Max
Unit
Zero Gate Voltage Drain Leakage Current
(VDS = 65 Vdc, VGS = 0 Vdc)
IDSS
—
—
10
μAdc
Zero Gate Voltage Drain Leakage Current
(VDS = 28 Vdc, VGS = 0 Vdc)
IDSS
—
—
1
μAdc
Gate--Source Leakage Current
(VGS = 5 Vdc, VDS = 0 Vdc)
IGSS
—
—
1
μAdc
Gate Threshold Voltage
(VDS = 10 Vdc, ID = 513 μAdc)
VGS(th)
1.2
2
2.7
Vdc
Gate Quiescent Voltage
(VDS = 28 Vdc, ID = 1400 mAdc)
VGS(Q)
—
2.7
—
Vdc
Fixture Gate Quiescent Voltage (1)
(VDD = 28 Vdc, ID = 1400 mAdc, Measured in Functional Test)
VGG(Q)
4
5.4
7
Vdc
Drain--Source On--Voltage
(VGS = 10 Vdc, ID = 5.13 Adc)
VDS(on)
0.1
0.2
0.3
Vdc
Reverse Transfer Capacitance
(VDS = 28 Vdc ± 30 mV(rms)ac @ 1 MHz, VGS = 0 Vdc)
Crss
—
2.17
—
pF
Output Capacitance
(VDS = 28 Vdc ± 30 mV(rms)ac @ 1 MHz, VGS = 0 Vdc)
Coss
—
257
—
pF
Input Capacitance
(VDS = 28 Vdc, VGS = 0 Vdc ± 30 mV(rms)ac @ 1 MHz)
Ciss
—
508
—
pF
Characteristic
Off Characteristics
On Characteristics
Dynamic Characteristics (2)
Functional Tests (In Freescale Test Fixture, 50 ohm system) VDD = 28 Vdc, IDQ = 1400 mA, Pout = 63 W Avg., f = 1987.5 MHz,
Single--Carrier W--CDMA, IQ Magnitude Clipping, Input Signal PAR = 7.5 dB @ 0.01% Probability on CCDF. ACPR measured in 3.84 MHz
Channel Bandwidth @ ±5 MHz Offset.
Power Gain
Gps
18
20
21.5
dB
Drain Efficiency
ηD
26
29
—
%
PAR
5.5
5.9
—
dB
ACPR
—
--33
--31
dBc
IRL
—
--9.5
--6
dB
Output Peak--to--Average Ratio @ 0.01% Probability on CCDF
Adjacent Channel Power Ratio
Input Return Loss
1. VGG = 2 x VGS(Q). Parameter measured on Freescale Test Fixture, due to resistive divider network on the board. Refer to Test Circuit
schematic.
2. Part internally matched both on input and output.
(continued)
MRF7S19210HR3 MRF7S19210HSR3
2
RF Device Data
Freescale Semiconductor
Table 4. Electrical Characteristics (TA = 25°C unless otherwise noted) (continued)
Characteristic
Symbol
Min
Typ
Max
Unit
Typical Performances (In Freescale Test Fixture, 50 ohm system) VDD = 28 Vdc, IDQ = 1400 mA, 1930--1990 MHz Bandwidth
IMD Symmetry @ 160 W PEP, Pout where IMD Third Order
Intermodulation 30 dBc
(Delta IMD Third Order Intermodulation between Upper and Lower
Sidebands > 2 dB)
IMDsym
VBW Resonance Point
(IMD Third Order Intermodulation Inflection Point)
MHz
—
15
—
VBWres
—
50
—
MHz
Gain Flatness in 60 MHz Bandwidth @ Pout = 63 W Avg.
GF
—
0.9
—
dB
Average Deviation from Linear Phase in 60 MHz Bandwidth
@ Pout = 190 W CW
Φ
—
0.95
—
°
Delay
—
2.82
—
ns
Part--to--Part Insertion Phase Variation @ Pout = 190 W CW,
f = 1960 MHz, Six Sigma Window
∆Φ
—
28.9
—
°
Gain Variation over Temperature
(--30°C to +85°C)
∆G
—
0.019
—
dB/°C
∆P1dB
—
0.008
—
dB/°C
Average Group Delay @ Pout = 190 W CW, f = 1960 MHz
Output Power Variation over Temperature
(--30°C to +85°C)
MRF7S19210HR3 MRF7S19210HSR3
RF Device Data
Freescale Semiconductor
3
Z22
R1
VBIAS
VSUPPLY
+
Z20
R2
C1
C2
C3
C10
C11
C12
C21
R3
RF
INPUT Z1
Z10
Z19
Z2
Z3
Z4
Z5
Z6
Z7
Z8
C6
C4
DUT
C5
RF
Z18 OUTPUT
C16
Z11 Z12 Z13
Z9
Z14 Z15
C14
Z17
C15
C13
Z21
Z16
C17
Z23
+
C9
Z1
Z2
Z3
Z4
Z5
Z6
Z7
Z8
Z9
Z10
Z11
Z12
C8
C18
C7
0.126″ x 0.066″ Microstrip
0.584″ x 0.079″ Microstrip
0.110″ x 0.079″ Microstrip
0.133″ x 0.079″ Microstrip
0.059″ x 0.118″ Microstrip
0.059″ x 0.118″ Microstrip
0.197″ x 0.102″ Microstrip
0.860″ x 0.551″ Microstrip
0.114″ x 0.551″ Microstrip
0.129″ x 1.102″ Microstrip
0.304″ x 1.102″ Microstrip
0.295″ x 0.276″ Microstrip
Z13
Z14
Z15
Z16
Z17
Z18
Z19
Z20
Z21
Z22, Z23
PCB
C19
C20
C22
0.078″ x 0.102″ Microstrip
0.319″ x 0.102″ Microstrip
0.709″ x 0.220″ Microstrip
0.709″ x 0.220″ Microstrip
0.747″ x 0.066″ Microstrip
0.227″ x 0.066″ Microstrip
0.145″ x 0.090″ Microstrip
0.548″ x 0.090″ Microstrip
0.734″ x 0.090″ Microstrip
1.044″ x 0.100″ Microstrip
Taconic RF35, 0.030″, εr = 3.5
Figure 1. MRF7S19210HR3(HSR3) Test Circuit Schematic
Table 5. MRF7S19210HR3(HSR3) Test Circuit Component Designations and Values
Part
Description
Part Number
Manufacturer
C1, C9, C11, C12, C19, C20
10 μF, 50 V Chip Capacitors
C5750X5R1H106M
TDK
C2, C8
100 nF Chip Capacitors
12065C104KAT2A
AVX
C3, C6, C7, C10, C14, C15,
C18
8.2 pF Chip Capacitors
ATC100B8R2BT500XT
ATC
C4
0.2 pF Chip Capacitor
ATC100B0R2BT500XT
ATC
C5
1.8 pF Chip Capacitor
ATC100B1R8BT500XT
ATC
C13
0.4 pF Chip Capacitor
ATC100B0R4BT500XT
ATC
C16, C17
0.5 pF Chip Capacitors
ATC100B0R5BT500XT
ATC
C21, C22
470 μF Electrolytic Capacitors
222212018471
Vishay BC Components
R1, R2
10 kΩ, 1/4 W Chip Resistors
WCR120610KFI
Welwyn
R3
10 Ω, 1/4 W Chip Resistor
WCR120610RFI
Welwyn
MRF7S19210HR3 MRF7S19210HSR3
4
RF Device Data
Freescale Semiconductor
C1
R2
C11 C12
C3
R3
C6
C4 C5
C8
C9
CUT OUT AREA
R1
C10
C2
C13
C21
C14
C16
C15
C17
C22
C19 C20
C7
C18
MRF7S19210H
Rev 0
Figure 2. MRF7S19210HR3(HSR3) Test Circuit Component Layout
MRF7S19210HR3 MRF7S19210HSR3
RF Device Data
Freescale Semiconductor
5
Gps, POWER GAIN (dB)
20
33
32
VDD = 28 Vdc, Pout = 63 W (Avg.)
IDQ = 1400 mA
19.5
31
19 Single--Carrier W--CDMA, 3.84 MHz Channel Bandwidth
Input Signal PAR = 7.5 dB @ 0.01% Probability on CCDF
18.5
18
30
PARC
17.5
17
16
1880
1900
--2
--32
--4
--33
--34
IRL
16.5
--31
ACPR
1920
1940
--35
1960
1980
2000
2020
--36
2040
--6
--8
--10
--12
--1.5
--2
--2.5
--3
--3.5
PARC (dB)
20.5
34
ηD
IRL, INPUT RETURN LOSS (dB)
Gps
ACPR (dBc)
21
ηD, DRAIN
EFFICIENCY (%)
TYPICAL CHARACTERISTICS
--4
f, FREQUENCY (MHz)
Figure 3. Output Peak--to--Average Ratio Compression (PARC)
Broadband Performance @ Pout = 63 Watts Avg.
IDQ = 2100 mA
1750 mA
1400 mA
19
18
1050 mA
VDD = 28 Vdc
f = 1960 MHz
17
700 mA
16
1
100
10
VDD = 28 Vdc, Pout = 160 W (PEP), IDQ = 1400 mA
Two--Tone Measurements
(f1 + f2)/2 = Center Frequency of 1960 MHz
--10
--20
IM3--U
--30
IM3--L
IM5--U
--40
--60
300
IM5--L
IM7--L
--50
IM7--U
10
1
100
TWO--TONE SPACING (MHz)
Figure 4. Power Gain versus Output Power
Figure 5. Intermodulation Distortion Products
versus Two--Tone Spacing
20.5
1
20
0
19.5
19
18.5
18
17.5
OUTPUT COMPRESSION AT 0.01%
PROBABILITY ON CCDF (dB)
Gps, POWER GAIN (dB)
Pout, OUTPUT POWER (WATTS) CW
Gps
PARC
--25
40
--30
ACPR
--1
35
--2
--1 dB = 48.916 W
--3 dB = 90.739 W 30
--2 dB = 68.142 W
--3
25
ηD
VDD = 28 Vdc, IDQ = 1400 mA, f = 1960 MHz
Single--Carrier W--CDMA, 3.84 MHz Channel Bandwidth
Input Signal PAR = 7.5 dB @ 0.01% Probability on CCDF
--4
--5
45
30
40
50
60
70
80
90
--35
--40
ACPR (dBc)
20
0
ηD, DRAIN EFFICIENCY (%)
21
Gps, POWER GAIN (dB)
IMD, INTERMODULATION DISTORTION (dBc)
22
--45
20
--50
15
--55
100
Pout, OUTPUT POWER (WATTS)
Figure 6. Output Peak--to--Average Ratio
Compression (PARC) versus Output Power
MRF7S19210HR3 MRF7S19210HSR3
6
RF Device Data
Freescale Semiconductor
TYPICAL CHARACTERISTICS
18
85_C
--10
40
85_C
25_C
14
--30_C
ηD
1
50
20
ACPR
12
--5
30
Input Signal PAR = 7.5 dB @ 0.01%
Probability on CCDF
16
60
10
10
0
300
100
--15
--20
--25
ACPR (dBc)
--30_C
25_C
VDD = 28 Vdc, IDQ = 1400 mA, f = 1960 MHz
Single--Carrier W--CDMA, 3.84 MHz
22 Channel Bandwidth
85_C
TC = --30_C
25_C
20
Gps
ηD, DRAIN EFFICIENCY (%)
Gps, POWER GAIN (dB)
24
--30
--35
Pout, OUTPUT POWER (WATTS) AVG.
Figure 7. Single--Carrier W--CDMA Power Gain, Drain
Efficiency and ACPR versus Output Power
0
20
--2
10
--4
5
--6
VDD = 28 Vdc
Pout = 9 dBm
IDQ = 1400 mA
0
--5
1550
1650
1750
1850
--8
IRL
1950
IRL (dB)
GAIN (dB)
Gain
15
2050
2150
2250
--10
2350
f, FREQUENCY (MHz)
Figure 8. Broadband Frequency Response
MRF7S19210HR3 MRF7S19210HSR3
RF Device Data
Freescale Semiconductor
7
W--CDMA TEST SIGNAL
100
10
0
--10
Input Signal
--30
0.1
0.01
W--CDMA. ACPR Measured in 3.84 MHz
Channel Bandwidth @ ±5 MHz Offset.
Input Signal PAR = 7.5 dB @ 0.01%
Probability on CCDF
0.001
0.0001
3.84 MHz
Channel BW
--20
1
(dB)
PROBABILITY (%)
10
0
1
2
3
4
5
6
--40
--50
--60
+ACPR in 3.84 MHz
Integrated BW
--ACPR in 3.84 MHz
Integrated BW
--70
--80
7
8
9
PEAK--TO--AVERAGE (dB)
Figure 9. CCDF W--CDMA IQ Magnitude
Clipping, Single--Carrier Test Signal
10
--90
--100
--9
--7.2 --5.4
--3.6 --1.8
0
1.8
3.6
5.4
7.2
9
f, FREQUENCY (MHz)
Figure 10. Single--Carrier W--CDMA Spectrum
MRF7S19210HR3 MRF7S19210HSR3
8
RF Device Data
Freescale Semiconductor
Zo = 5 Ω
f = 2040 MHz
f = 2040 MHz
f = 1880 MHz
Zsource
Zload
f = 1880 MHz
VDD = 28 Vdc, IDQ = 1400 mA, Pout = 63 W Avg.
f
MHz
Zsource
Ω
Zload
Ω
1880
5.20 -- j1.02
1.49 -- j1.45
1900
4.90 -- j1.00
1.52 -- j1.30
1920
4.60 -- j0.92
1.55 -- j1.16
1940
4.31 -- j0.82
1.58 -- j1.04
1960
4.04 -- j0.71
1.61 -- j0.93
1980
3.80 -- j0.56
1.66 -- j0.82
2000
3.58 -- j0.42
1.73 -- j0.70
2020
3.38 -- j0.30
1.81 -- j0.57
2040
3.19 -- j0.16
1.88 -- j0.49
Zsource = Test circuit impedance as measured from
gate to ground.
Zload
= Test circuit impedance as measured from
drain to ground.
Output
Matching
Network
Device
Under
Test
Input
Matching
Network
Z
source
Z
load
Figure 11. Series Equivalent Source and Load Impedance
MRF7S19210HR3 MRF7S19210HSR3
RF Device Data
Freescale Semiconductor
9
ALTERNATIVE PEAK TUNE LOAD PULL CHARACTERISTICS
60
60
57
56
59
Ideal
P3dB = 55.27 dBm (337 W)
58
Pout, OUTPUT POWER (dBm)
Pout, OUTPUT POWER (dBm)
59
P1dB = 54.35 dBm (272 W)
55
Actual
54
53
52
VDD = 28 Vdc, IDQ = 1400 mA, Pulsed CW
10 μsec(on), 10% Duty Cycle, f = 1930 MHz
51
50
29
30
31
32
33
34
35
36
37
38
57
P1dB = 54.29 dBm (269 W)
56
55
Actual
54
53
52
VDD = 28 Vdc, IDQ = 1400 mA, Pulsed CW
10 μsec(on), 10% Duty Cycle, f = 1990 MHz
51
39
Ideal
P3dB = 55.25 dBm (335 W)
58
50
29
30
31
32
33
34
35
36
37
38
39
Pin, INPUT POWER (dBm)
Pin, INPUT POWER (dBm)
NOTE: Load Pull Test Fixture Tuned for Peak P1dB Output Power @ 28 V
NOTE: Load Pull Test Fixture Tuned for Peak P1dB Output Power @ 28 V
Test Impedances per Compression Level
Test Impedances per Compression Level
P1dB
Zsource
Ω
Zload
Ω
5.72 -- j5.51
1.30 -- j0.69
Figure 12. Pulsed CW Output Power
versus Input Power @ 28 V @ 1930 MHz
P1dB
Zsource
Ω
Zload
Ω
6.20 + j1.19
1.09 -- j046
Figure 13. Pulsed CW Output Power
versus Input Power @ 28 V @ 1990 MHz
MRF7S19210HR3 MRF7S19210HSR3
10
RF Device Data
Freescale Semiconductor
PACKAGE DIMENSIONS
MRF7S19210HR3 MRF7S19210HSR3
RF Device Data
Freescale Semiconductor
11
MRF7S19210HR3 MRF7S19210HSR3
12
RF Device Data
Freescale Semiconductor
MRF7S19210HR3 MRF7S19210HSR3
RF Device Data
Freescale Semiconductor
13
MRF7S19210HR3 MRF7S19210HSR3
14
RF Device Data
Freescale Semiconductor
PRODUCT DOCUMENTATION AND SOFTWARE
Refer to the following documents and software to aid your design process.
Application Notes
• AN1955: Thermal Measurement Methodology of RF Power Amplifiers
Engineering Bulletins
• EB212: Using Data Sheet Impedances for RF LDMOS Devices
Software
• Electromigration MTTF Calculator
• RF High Power Model
For Software, do a Part Number search at http://www.freescale.com, and select the “Part Number” link. Go to the Software &
Tools tab on the part’s Product Summary page to download the respective tool.
REVISION HISTORY
The following table summarizes revisions to this document.
Revision
Date
Description
0
Dec. 2008
• Initial Release of Data Sheet
1
Mar. 2011
• Modified data sheet to reflect RF Test Reduction described in Product and Process Change Notification
number, PCN13628, p. 1, 2
• Fig. 9, MTTF versus Junction Temperature removed, p. 7. Refer to the device’s MTTF Calculator
available at freescale.com/RFpower. Go to Design Resources > Software and Tools.
• Fig. 10, CCDF W--CDMA IQ Magnitude Clipping, Single--Carrier Test Signal and Fig. 11, Single--Carrier
W--CDMA Spectrum updated to show the undistorted input test signal, p. 8 (renumbered as Figs. 9 and 10
respectively after Fig. 9 removed)
• Added Electromigration MTTF Calculator and RF High Power Model availability to Product Software,
p. 15
MRF7S19210HR3 MRF7S19210HSR3
RF Device Data
Freescale Semiconductor
15
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
1--800--521--6274 or +1--480--768--2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1--8--1, Shimo--Meguro, Meguro--ku,
Tokyo 153--0064
Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
+86 10 5879 8000
support.asia@freescale.com
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
1--800--441--2447 or +1--303--675--2140
Fax: +1--303--675--2150
LDCForFreescaleSemiconductor@hibbertgroup.com
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescalet and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2008, 2011. All rights reserved.
MRF7S19210HR3 MRF7S19210HSR3
Document Number: MRF7S19210H
Rev. 1, 3/2011
16
RF Device Data
Freescale Semiconductor