NE5234D,518

INTEGRATED CIRCUITS NE/SA5234 Matched quad high-performance low-voltage operational amplifier Product data Supersedes data of 2001 Aug 03 File under Integrated Circuits, IC11 Handbook 
   2002 Feb 22 Philips Semiconductors Product data Matched quad high-performance low-voltage operational amplifier NE/SA5234 DESCRIPTION PIN CONFIGURATION The NE/SA5234 is a matched, low voltage, high performance quad operational amplifier. Among its unique input and output characteristics is the capability for both input and output rail-to-rail operation, particularly critical in low voltage applications. The output swings to less than 50 mV of both rails across the entire power supply range. The NE/SA5234 is capable of delivering 5.5 V peak-to-peak across a 600 Ω load and will typically draw only 700 µA per amplifier. The bandwidth is 2.5 MHz and the 1% settling time is 1.4 µs. N and D Packages FEATURES • Wide common-mode input voltage range: 250 mV beyond both rails • Output swing within 50 mV of both rails • Functionality to 1.8 V typical • Low current consumption: 700 µA per amplifier • ±15 mA output current capability • Unity gain bandwidth: 2.5 MHz • Slew rate: 0.8 V/µs • Low noise: 25 nV/√Hz • Electrostatic discharge protection • Short-circuit protection • Output inversion prevention OUTPUT1 1 14 OUTPUT4 –INPUT1 2 13 –INPUT4 +INPUT1 3 12 +INPUT4 VCC 4 11 GND +INPUT2 5 10 +INPUT3 –INPUT2 6 9 –INPUT3 OUTPUT2 7 8 OUTPUT3 SL00568 Figure 1. Pin configuration. APPLICATIONS • Automotive electronics • Signal conditioning and sensing amplification • Portable instrumentation – Test and measurement – Medical monitors and diagnostics – Remote meters • Audio equipment • Security systems • Communications – Pagers – Cellular telephone – LAN – 5 V Datacom bus • Error amplifier in motor drives • Transducer buffer amplifier ORDERING INFORMATION DESCRIPTION TEMPERATURE RANGE ORDER CODE DWG # 0 °C to +70 °C NE5234D SOT108-1 14-Pin Plastic Dual In-Line Package (DIP) 0 °C to +70 °C NE5234N SOT27-1 14-Pin Plastic Small Outline (SO) package –40 °C to +85 °C SA5234D SOT108-1 14-Pin Plastic Dual In-Line Package (DIP) –40 °C to +85 °C SA5234N SOT27-1 14-Pin Plastic Small Outline (SO) package 2002 Feb 22 2 853-1445 27774 Philips Semiconductors Product data Matched quad high-performance low-voltage operational amplifier NE/SA5234 ABSOLUTE MAXIMUM RATINGS SYMBOL PARAMETER VCC Single supply voltage VESD ESD protection voltage at any pin5 human body model robot model RATING UNIT 7 V 2000 200 V V ±3.5 V VS Dual supply voltage VDP Voltage at any device pin1 IDP Current into any device pin1 VIN Differential input voltage2 VCM Common-mode input voltage (positive) VCM Common-mode input voltage (negative) VEE – 0.5 V 500 mW +150 °C PD Power dissipation3 Tj Operating junction temperature3 VSC Supply voltage allowing indefinite output short circuit to either Tstg Storage temperature range Tsld Lead soldering temperature (10 sec max) θJA Thermal impedance 14 pin Plastic DIP 14 pin Plastic SO rail3,4 VS ±0.5 V ±50 mA 0.5 V VCC + 0.5 V 7 V –65 to +150 °C +230 °C 80 115 °C/W °C/W NOTES: 1. Each pin is protected by ESD diodes. The voltage at any pin is limited by the ESD diodes. 2. The differential input of each amplifier is limited by two internal diodes, connected in parallel and opposite to each other. For more differential input range, use differential resistors in series with the input pins. 3. The maximum operating junction temperature is +150 °C. At elevated temperatures, devices must be derated according to the package thermal resistance and device mounting conditions. Derates above +25 °C: N package at 9.5 mW/°C; D package at 6.25 mW/°C. 4. Simultaneous short circuits of two or more amplifiers to the positive or negative rail can exceed the power dissipation ratings and cause eventual destruction of the device. 5. Guaranteed by design. RECOMMENDED OPERATING CONDITIONS SYMBOL RATING UNIT Single supply voltage +2 to +5.5 V Dual supply voltage ±1 to ±2.75 V VCM Common-mode input voltage (positive) VCC + 0.25 V VCM Common-mode input voltage (negative) VEE – 0.25 V Tamb Temperature NE5234 SA5234 0 to +70 –40 to +85 °C °C VCC VS 2002 Feb 22 PARAMETER 3 Philips Semiconductors Product data Matched quad high-performance low-voltage operational amplifier NE/SA5234 DC ELECTRICAL CHARACTERISTICS VCC = 2 V to 5.5 V; VEE = 0 V; Tamb = 25 °C; VEE < VCM < VCC; unless otherwise stated. LIMITS SYMBOL PARAMETER TEST CONDITIONS NE5234 MIN TYP MAX TYP MAX 2.8 4.0 2.8 4.0 3.0 4.6 3.2 4.8 ±0.2 ±4 ±0.2 ±4 ±0.4 ±5 ±0.6 ±5 Supply current VCC = 5.5 V over full temperature range VOS Offset voltage Over full temperature range ∆VOS IOS ∆IOS/∆T IB ∆IB/∆T ∆IB VCM Offset voltage drift with temperature Offset voltage difference between any amplifiers am lifiers in the same package at the same common mode level1 Offset current Input bias current difference between anyy amplifier in the same package at the same common mode level. level Common-mode input range CMRR Common mode rejection Common-mode ratio, large signal PSRR Power supply rejection ratio IL Peak load current, current sink and source mA mV µV/°C 4 0.4 3 0.4 3 0.8 4 1.2 4 ±3 ±20 ±3 ±30 ±4 ±30 ±6 ±60 0.02 ±0.3 0.03 ±0.3 mV Over full temperature range Over full temperature range VEE < VCM < VEE +0.5 V –200 –90 –200 –90 Over full temperature range –225 –100 –250 –150 VEE +1 V < VCM < VCC 25 70 25 75 Over full temperature range 35 100 35 120 Input bias current drift with temperature Common-mode rejection j ratio, small signal 2002 Feb 22 4 Offset current drift with temperature Input bias current1 MIN UNIT VCC = 5.5 V ICC ∆VOS/∆T SA5234 0.5 0.5 10 30 10 30 Over full temperature range 25 50 50 70 VEE +1V < VCM < VCC 5 20 5 20 Over full temperature range 15 30 25 50 VOS ≤ 6 mV VEE–0.25 VCC+0.25 VEE–0.25 VCC+0.25 VOS ≤ 6 mV over full temperature range VEE–0.1 VCC+0.1 VEE–0.1 VCC+0.1 VEE < VCM < VEE+0.5 V; VEE+1 V < VCM < VCC 80 Over full temperature range 75 VEE < VCM < VCC 65 Over full temperature range 60 VEE < VCM < VCC 80 100 80 100 Over full temperature range 80 90 80 90 10 12 10 12 5 8 5 8 Over full temperature range 4 90 65 nA nA V 100 80 90 nA/°C nA/°C VEE < VCM < VEE +0.5V 100 nA dB 100 60 dB mA Philips Semiconductors Product data Matched quad high-performance low-voltage operational amplifier NE/SA5234 DC ELECTRICAL CHARACTERISTICS (Continued) LIMITS SYMBOL AVOL TEST CONDITIONS PARAMETER Open-loop voltage gain NE5234 MIN TYP 90 110 Over full temperature range MIN TYP 90 110 90 UNIT MAX dB 90 IPEAK = 0.1 mA VEE+0.05 VCC–0.05 VEE+0.1 VCC–0.1 IPEAK = 10 mA VEE+0.25 VCC–0.25 VEE+0.25 VCC–0.25 IPEAK = 5 mA over full temperature range VEE+0.22 VCC–0.2 VEE+0.2 VCC–0.2 RL = 2 kΩ VEE+0.2 VCC–0.2 VEE+0.2 VCC–0.2 RL = 600 Ω VEE+0.25 VCC–0.25 VEE+0.25 VCC–0.25 Output Out ut voltage swing VOUT SA5234 MAX Output voltage g swing g for VCC = 2.75 V; VEE = –2.75 V V V NOTE: 1. These parameters are measured for VEE < VCM < VEE+0.5 V and for VEE+1 V < VCM < VCC. By design these parameters are intermediate for common mode ranges between the measured regions. AC ELECTRICAL CHARACTERISTICS Tamb = +25 °C; VCC = 2 V to 5.5 V; RL = 10 kΩ; CL = 100 pF; unless otherwise stated. LIMITS SYMBOL PARAMETER NE5234 TEST CONDITIONS MIN TYP SR Slew rate Over full temperature range 0.5 0.8 BW Unity gain bandwidth: –3 dB Over full temperature range 2 2.5 θM Phase Margin tS 1% settling time VN Input referred voltage noise THD Total harmonic distortion SA/SE5234 MAX 4.0 MIN TYP 0.5 0.8 2 2.5 UNITS MAX V/µs 4.0 MHz CL = 50 pF 55 55 deg AV = 1, 1 V step 1.4 1.4 µs AV = 1; RS = 0 Ω, at 1 kHz 25 25 nV/Hz1/2 10 kHz, 1 VP-P, AV = 1 0.1 0.1 % OUTPUT INVERSION PREVENTION VIN VCC VIN VOUT VCC VCC VOUT 47 kΩ 5V 5V + VIN VGND t 47 kΩ VOUT – t VGND VGND CONVENTIONAL OP AMP PHILIPS NE5234 Figure 2. Output inversion prevention. 2002 Feb 22 5 SL00569 Philips Semiconductors Product data Matched quad high-performance low-voltage operational amplifier NE/SA5234 SO14: plastic small outline package; 14 leads; body width 3.9 mm 2002 Feb 22 6 SOT108-1 Philips Semiconductors Product data Matched quad high-performance low-voltage operational amplifier NE/SA5234 DIP14: plastic dual in-line package; 14 leads (300 mil) 2002 Feb 22 7 SOT27-1 Philips Semiconductors Product data Matched quad high-performance low-voltage operational amplifier NE/SA5234 Data sheet status Data sheet status [1] Product status [2] Definitions Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.  Koninklijke Philips Electronics N.V. 2002 All rights reserved. Printed in U.S.A. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Date of release: 03-02 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. Document order number: 
   2002 Feb 22 8 9397 750 09514