NX3L1T3157GM,115

NX3L1T3157 Low-ohmic single-pole double-throw analog switch Rev. 9.2 — 11 December 2019 Product data sheet 1. General description The NX3L1T3157 is a low-ohmic single-pole double-throw analog switch suitable for use as an analog or digital 2:1 multiplexer/demultiplexer. It has a digital select input (S), two independent inputs/outputs (Y0 and Y1) and a common input/output (Z). Schmitt trigger action at the digital input makes the circuit tolerant to slower input rise and fall times. Low threshold digital input allows this device to be driven by 1.8 V logic levels in 3.3 V applications without significant increase in supply current ICC. This makes it possible for the NX3L1T3157 to switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for logic level translation. The NX3L1T3157 allows signals with amplitude up to VCC to be transmitted from Z to Y0 or Y1, or from Y0 or Y1 to Z. Its low ON resistance (0.5 ) and flatness (0.13 ) ensures minimal attenuation and distortion of transmitted signals. 2. Features and benefits  Wide supply voltage range from 1.4 V to 4.3 V  Very low ON resistance (peak):  1.6  (typical) at VCC = 1.4 V  1.0  (typical) at VCC = 1.65 V  0.55  (typical) at VCC = 2.3 V  0.50  (typical) at VCC = 2.7 V  0.50  (typical) at VCC = 4.3 V  Break-before-make switching  High noise immunity  ESD protection:  HBM JESD22-A114F Class 3A exceeds 7500 V  MM JESD22-A115-A exceeds 200 V  CDM AEC-Q100-011 revision B exceeds 1000 V  IEC61000-4-2 contact discharge exceeds 8000 V for switch ports  CMOS low-power consumption  Latch-up performance exceeds 100 mA per JESD78 Class II Level A  1.8 V control logic at VCC = 3.6 V  Control input accepts voltages above supply voltage  Very low supply current, even when input is below VCC  High current handling capability (350 mA continuous current under 3.3 V supply)  Specified from 40 C to +85 C and from 40 C to +125 C NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 3. Applications  Cell phone  PDA  Portable media player 4. Ordering information Table 1. Ordering information Type number Topside marking[1] Package NX3L1T3157GM MI [1] Name Description Version XSON6 plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm SOT886 The pin 1 indicator is located on the lower left corner of the device, below the marking code. 4.1 Ordering options Table 2. Ordering options Type number Orderable part number NX3L1T3157GM NX3L1T3157GM Package Packing method Minimum order quantity Temperature NX3L1T3157GM,115[1] XSON6 REEL 7" Q1 NDP 5000 Tamb = 40 C to +125 C NX3L1T3157GMZ REEL 7" Q1 NDP SSB[2] 5000 Tamb = 40 C to +125 C XSON6 [1] Will go EOL - migrate to new leadframe orderable part number [2] This packing method uses a Static Shielding Bag (SSB) solution. Material is to be kept in the sealed bag between uses. 5. Functional diagram Y1 S Z S 6 1 Y1 Z 4 Y0 3 Y0 001aac355 001aac354 Fig 1. Logic symbol NX3L1T3157 Product data sheet Fig 2. Logic diagram All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 2 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 6. Pinning information 6.1 Pinning NX3L1T3157 Y1 1 6 S GND 2 5 VCC Y0 3 4 Z 001aah441 Transparent top view Fig 3. Pin configuration SOT886 (XSON6) 6.2 Pin description Table 3. Pin description Symbol Pin Description Y1 1 independent input or output GND 2 ground (0 V) Y0 3 independent input or output Z 4 common output or input VCC 5 supply voltage S 6 select input 7. Functional description Table 4. Function table[1] Input S Channel on L Y0 H Y1 [1] H = HIGH voltage level; L = LOW voltage level. NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 3 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 8. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter VCC supply voltage VI input voltage VSW switch voltage IIK input clamping current VI < 0.5 V ISK switch clamping current VI < 0.5 V or VI > VCC + 0.5 V ISW switch current VSW > 0.5 V or VSW < VCC + 0.5 V; source or sink current VSW > 0.5 V or VSW < VCC + 0.5 V; pulsed at 1 ms duration, < 10 % duty cycle; peak current Tstg Conditions Min select input S total power dissipation Tamb = 40 C to +125 C Unit 0.5 +4.6 V [1] 0.5 +4.6 V [2] 0.5 VCC + 0.5 V 50 - mA - 50 mA - 350 mA - 500 mA 65 +150 C - 250 mW storage temperature Ptot Max [3] [1] The minimum input voltage rating may be exceeded if the input current rating is observed. [2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not exceed 4.6 V. [3] For XSON6 package: above 118 C the value of Ptot derates linearly with 7.8 mW/K. 9. Recommended operating conditions Table 6. Recommended operating conditions Symbol Parameter VCC supply voltage VI input voltage VSW switch voltage Tamb ambient temperature t/V input transition rise and fall rate Conditions select input S [1] VCC = 1.4 V to 4.3 V [2] Min Max Unit 1.4 4.3 V 0 4.3 V 0 VCC V 40 +125 C - 200 ns/V [1] To avoid sinking GND current from terminal Z when switch current flows in terminal Yn, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal Z, no GND current will flow from terminal Yn. In this case, there is no limit for the voltage drop across the switch. [2] Applies to control signal levels. NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 4 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 10. Static characteristics Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground 0 V). Symbol Parameter VIH VIL HIGH-level input voltage LOW-level input voltage Tamb = 25 C Conditions Typ Max Min VCC = 1.4 V to 1.6 V 0.9 - - 0.9 - - V VCC = 1.65 V to 1.95 V 0.9 - - 0.9 - - V VCC = 2.3 V to 2.7 V 1.1 - - 1.1 - - V 1.3 - - 1.3 - - V VCC = 3.6 V to 4.3 V 1.4 - - 1.4 - - V VCC = 1.4 V to 1.6 V - - 0.3 - 0.3 0.3 V VCC = 1.65 V to 1.95 V - - 0.4 - 0.4 0.3 V VCC = 2.3 V to 2.7 V - - 0.4 - 0.4 0.4 V VCC = 2.7 V to 3.6 V - - 0.5 - 0.5 0.5 V VCC = 3.6 V to 4.3 V - - 0.6 - 0.6 0.6 V - - - - 0.5 1 A VCC = 1.4 V to 3.6 V - - 5 - 50 500 nA VCC = 3.6 V to 4.3 V - - 10 - 50 500 nA VCC = 1.4 V to 3.6 V - - 5 - 50 500 nA VCC = 3.6 V to 4.3 V - - 10 - 50 500 nA VCC = 3.6 V - - 100 - 690 6000 nA VCC = 4.3 V - - 150 - 800 7000 nA - 2.0 4.0 - 7 7 A VI = 2.6 V; VCC = 3.6 V - 0.35 0.7 - 1 1 A VI = 1.8 V; VCC = 4.3 V - 7.0 10.0 - 15 15 A VI = 1.8 V; VCC = 3.6 V - 2.5 4.0 - 5 5 A VI = 1.8 V; VCC = 2.5 V - 50 200 - 300 500 nA select input S; VI = GND to 4.3 V; VCC = 1.4 V to 4.3 V IS(OFF) OFF-state leakage current Y0 and Y1 port; see Figure 4 ICC ICC Max Max (85 C) (125 C) VCC = 2.7 V to 3.6 V input leakage current ON-state leakage current Unit Min II IS(ON) Tamb = 40 C to +125 C Z port; see Figure 5 supply current VI = VCC or GND; VSW = GND or VCC additional VSW = GND or VCC supply current VI = 2.6 V; VCC = 4.3 V CI input capacitance - 1.0 - - - - pF CS(OFF) OFF-state capacitance - 35 - - - - pF CS(ON) ON-state capacitance - 130 - - - - pF NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 5 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 10.1 Test circuits VCC VIL or VIH S Y0 1 Z Y1 2 switch switch S 1 VIH 2 VIL IS VI VO GND 001aac358 VI = 0.3 V or VCC  0.3 V; VO = VCC  0.3 V or 0.3 V. Fig 4. Test circuit for measuring OFF-state leakage current VCC VIL or VIH IS S Y0 1 Z Y1 2 VI switch S 1 VIH 2 VIL switch VO GND 001aac359 VI = 0.3 V or VCC  0.3 V; VO = VCC  0.3 V or 0.3 V. Fig 5. Test circuit for measuring ON-state leakage current NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 6 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 10.2 ON resistance Table 8. ON resistance At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 7 to Figure 13. Symbol RON(peak) Parameter ON resistance (peak) Tamb = 40 C to +85 C Tamb = 40 C to +125 C Unit Conditions Min Typ[1] Max Min Max VCC = 1.4 V - 1.6 3.7 - 4.1 VCC = 1.65 V - 1.0 1.6 - 1.7  VCC = 2.3 V - 0.55 0.8 - 0.9  VCC = 2.7 V - 0.5 0.75 - 0.9  - 0.5 0.75 - 0.9  VCC = 1.4 V - 0.04 0.3 - 0.3  VCC = 1.65 V - 0.04 0.2 - 0.3  VI = GND to VCC; ISW = 100 mA; see Figure 6 VCC = 4.3 V RON ON resistance mismatch between channels [2] VI = GND to VCC; ISW = 100 mA VCC = 2.3 V - 0.02 0.08 - 0.1  VCC = 2.7 V - 0.02 0.075 - 0.1  - 0.02 0.075 - 0.1  VCC = 1.4 V - 1.0 3.3 - 3.6  VCC = 1.65 V - 0.5 1.2 - 1.3  VCC = 2.3 V - 0.15 0.3 - 0.35  VCC = 2.7 V - 0.13 0.3 - 0.35  VCC = 4.3 V - 0.2 0.4 - 0.45  VCC = 4.3 V RON(flat) ON resistance (flatness)  [3] VI = GND to VCC; ISW = 100 mA [1] Typical values are measured at Tamb = 25 C. [2] Measured at identical VCC, temperature and input voltage. [3] Flatness is defined as the difference between the maximum and minimum value of ON resistance measured at identical VCC and temperature. NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 7 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 10.3 ON resistance test circuit and graphs 001aag564 1.6 RON (Ω) 1.2 (1) VSW V VCC S VIL or VIH Z Y0 1 switch Y1 2 VI 0.8 switch S 1 VIL 2 VIH (2) (3) (4) 0.4 (5) (6) ISW 0 GND 0 1 2 RON = VSW / ISW. 3 4 5 VI (V) 001aag563 (1) VCC = 1.5 V. (2) VCC = 1.8 V. (3) VCC = 2.5 V. (4) VCC = 2.7 V. (5) VCC = 3.3 V. (6) VCC = 4.3 V. Measured at Tamb = 25 C. Fig 6. Test circuit for measuring ON resistance NX3L1T3157 Product data sheet Fig 7. Typical ON resistance as a function of input voltage All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 8 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 001aag565 1.6 001aag566 1.0 RON (Ω) RON (Ω) 0.8 1.2 (1) (2) (3) (4) 0.6 (1) (2) (3) (4) 0.8 0.4 0.4 0.2 0 0 0 1 2 3 0 1 2 VI (V) (1) Tamb = 125 C. (1) Tamb = 125 C. (2) Tamb = 85 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (3) Tamb = 25 C. (4) Tamb = 40 C. (4) Tamb = 40 C. Fig 8. ON resistance as a function of input voltage; VCC = 1.5 V 001aag567 1.0 3 VI (V) RON (Ω) Fig 9. ON resistance as a function of input voltage; VCC = 1.8 V 001aag568 1.0 RON (Ω) 0.8 0.8 0.6 0.6 (1) (2) (3) (4) 0.4 0.4 0.2 0.2 0 (1) (2) (3) (4) 0 0 1 2 3 0 VI (V) (1) Tamb = 125 C. (2) Tamb = 85 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (3) Tamb = 25 C. (4) Tamb = 40 C. (4) Tamb = 40 C. Fig 10. ON resistance as a function of input voltage; VCC = 2.5 V Product data sheet 2 3 VI (V) (1) Tamb = 125 C. NX3L1T3157 1 Fig 11. ON resistance as a function of input voltage; VCC = 2.7 V All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 9 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 001aag569 1.0 001aaj896 1.0 RON (Ω) RON (Ω) 0.8 0.8 0.6 0.6 (1) (2) (3) (4) 0.4 (1) (2) (3) (4) 0.4 0.2 0.2 0 0 0 1 2 3 4 0 1 2 3 4 VI (V) (1) Tamb = 125 C. (1) Tamb = 125 C. (2) Tamb = 85 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (3) Tamb = 25 C. (4) Tamb = 40 C. (4) Tamb = 40 C. Fig 12. ON resistance as a function of input voltage; VCC = 3.3 V 5 VI (V) Fig 13. ON resistance as a function of input voltage; VCC = 4.3 V 11. Dynamic characteristics Table 9. Dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for load circuit see Figure 16. Symbol Parameter ten tdis enable time disable time NX3L1T3157 Product data sheet 25 C Conditions 40 C to +125 C Unit Min Typ[1] Max Min Max (85 C) Max (125 C) VCC = 1.4 V to 1.6 V - 50 90 - 120 120 ns VCC = 1.65 V to 1.95 V - 36 70 - 80 90 ns VCC = 2.3 V to 2.7 V - 24 45 - 50 55 ns VCC = 2.7 V to 3.6 V - 22 40 - 45 50 ns VCC = 3.6 V to 4.3 V - 22 40 - 45 50 ns VCC = 1.4 V to 1.6 V - 32 70 - 80 90 ns VCC = 1.65 V to 1.95 V - 20 55 - 60 65 ns VCC = 2.3 V to 2.7 V - 12 25 - 30 35 ns VCC = 2.7 V to 3.6 V - 10 20 - 25 30 ns VCC = 3.6 V to 4.3 V - 10 20 - 25 30 ns S to Z or Yn; see Figure 14 S to Z or Yn; see Figure 14 All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 10 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch Table 9. Dynamic characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for load circuit see Figure 16. Symbol Parameter tb-m 25 C Conditions 40 C to +125 C Unit Min Typ[1] Max Min Max (85 C) Max (125 C) - 19 - 9 - - ns VCC = 1.65 V to 1.95 V - 17 - 7 - - ns VCC = 2.3 V to 2.7 V - 13 - 4 - - ns VCC = 2.7 V to 3.6 V - 10 - 3 - - ns VCC = 3.6 V to 4.3 V - 10 - 2 - - ns break-before-make see Figure 15 time VCC = 1.4 V to 1.6 V [2] [1] Typical values are measured at Tamb = 25 C and VCC = 1.5 V, 1.8 V, 2.5 V, 3.3 V and 4.3 V respectively. [2] Break-before-make guaranteed by design. 11.1 Waveform and test circuits VI VM S input GND ten VOH Y1 connected to VEXT tdis VX Z output OFF to HIGH HIGH to OFF VX GND tdis Y0 connected to VEXT Z output HIGH to OFF OFF to HIGH VOH ten VX VX 001aag570 GND Measurement points are given in Table 10. Logic level: VOH is typical output voltage level that occurs with the output load. Fig 14. Enable and disable times Table 10. Measurement points Supply voltage Input Output VCC VM VX 1.4 V to 4.3 V 0.5VCC 0.9VOH NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 11 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch VCC S Y0 Z G VI V VO RL Y1 VEXT = 1.5 V CL GND 001aag571 a. Test circuit VI 0.5VI 0.9VO 0.9VO VO tb-m 001aag572 b. Input and output measurement points Fig 15. Test circuit for measuring break-before-make timing VCC G VI V VO RL S Y0 1 Z Y1 2 switch VEXT = 1.5 V CL GND 001aag642 Test data is given in Table 11. Definitions test circuit: RL = Load resistance. CL = Load capacitance including jig and probe capacitance. VEXT = External voltage for measuring switching times. Fig 16. Load circuit for switching times Table 11. Test data Supply voltage Input VCC VI tr, tf CL RL 1.4 V to 4.3 V VCC  2.5 ns 35 pF 50  NX3L1T3157 Product data sheet Load All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 12 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 11.2 Additional dynamic characteristics Table 12. Additional dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); VI = GND or VCC (unless otherwise specified); tr = tf  2.5 ns; Tamb = 25 C. Symbol Parameter Conditions THD fi = 20 Hz to 20 kHz; RL = 32 ; see Figure 17 total harmonic distortion Min 0.15 - % VCC = 1.65 V; VI = 1.2 V (p-p) - 0.10 - % VCC = 2.3 V; VI = 1.5 V (p-p) - 0.02 - % VCC = 2.7 V; VI = 2 V (p-p) - 0.02 - % - 0.02 - % - 60 - MHz - 90 - dB VCC = 1.4 V to 3.6 V - 0.2 - V VCC = 3.6 V to 4.3 V - 0.3 - V VCC = 1.5 V - 3 - pC VCC = 1.8 V - 4 - pC VCC = 2.5 V - 6 - pC VCC = 3.3 V - 9 - pC VCC = 4.3 V - 15 - pC 3 dB frequency response RL = 50 ; see Figure 18 iso isolation (OFF-state) fi = 100 kHz; RL = 50 ; see Figure 19 [1] VCC = 1.4 V to 4.3 V [1] VCC = 1.4 V to 4.3 V charge injection Qinj [1] Unit - f(3dB) crosstalk voltage Max VCC = 1.4 V; VI = 1 V (p-p) VCC = 4.3 V; VI = 2 V (p-p) Vct Typ [1] between digital inputs and switch; fi = 1 MHz; CL = 50 pF; RL = 50 ; see Figure 20 fi = 1 MHz; CL = 0.1 nF; RL = 1 M; Vgen = 0 V; Rgen = 0 ; see Figure 21 fi is biased at 0.5VCC. 11.3 Test circuits VCC 0.5VCC RL S VIL or VIH Z Y0 1 switch Y1 2 fi switch S 1 VIL 2 VIH D GND 001aag573 Fig 17. Test circuit for measuring total harmonic distortion NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 13 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch VCC 0.5VCC RL S VIL or VIH Y0 1 switch Y1 2 Z fi switch S 1 VIL 2 VIH dB GND 001aag574 Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads 3 dB. Fig 18. Test circuit for measuring the frequency response when channel is in ON-state 0.5VCC VCC 0.5VCC RL RL S VIL or VIH Y0 1 switch Y1 2 Z fi switch S 1 VIH 2 VIL dB GND 001aag561 Adjust fi voltage to obtain 0 dBm level at input. Fig 19. Test circuit for measuring isolation (OFF-state) NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 14 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch VCC VI G logic input S Y0 1 Z Y1 2 switch S 1 VIL 2 VIH switch RL RL 0.5VCC 0.5VCC CL V VO 001aah442 a. Test circuit logic input (S) off on off Vct VO 001aah443 b. Input and output pulse definitions Fig 20. Test circuit for measuring crosstalk voltage between digital inputs and switch NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 15 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch VCC S Y0 1 Z Y1 2 switch Rgen VI G VO RL CL Vgen GND 001aac366 a. Test circuit logic (S) off input on VO off ΔVO 001aac478 b. Input and output pulse definitions Definition: Qinj = VO  CL. VO = output voltage variation. Rgen = generator resistance. Vgen = generator voltage. Fig 21. Test circuit for measuring charge injection NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 16 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 12. Package outline SOT886 XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm b 1 2 3 4x (2) L L1 e 6 5 e1 4 e1 6x A (2) A1 D E terminal 1 index area 0 1 2 mm scale Dimensions (mm are the original dimensions) Unit mm max nom min A(1) 0.5 A1 b D E 0.04 0.25 1.50 1.05 0.20 1.45 1.00 0.17 1.40 0.95 e e1 0.6 0.5 L L1 0.35 0.40 0.30 0.35 0.27 0.32 Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. Outline version SOT886 sot886_po References IEC JEDEC JEITA European projection Issue date 04-07-22 12-01-05 MO-252 Fig 22. Package outline SOT886 (XSON6) NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 17 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 13. Abbreviations Table 13. Abbreviations Acronym Description CDM Charged Device Model CMOS Complementary Metal-Oxide Semiconductor ESD ElectroStatic Discharge HBM Human Body Model MM Machine Model PDA Personal Digital Assistant 14. Revision history Table 14. Revision history Document ID Release date Data sheet status Change notice Supersedes NX3L1T3157 v.9.2 20191211 Product data sheet - NX3L1T3157 v.9.1 Modifications: NX3L1T3157 v.9.1 Modifications: NX3L1T3157 v.9 Modifications: • Corrected temperature range in Table 2 “Ordering options” from “-40 C to +85 C” to “-40 C to +125 C” 20191203 Product data sheet - NX3L1T3157 v.9 • Package SOT886 requiring SSB added. Refer to PCN number 201909001 XSON6 (SOT886) Assembly/Test Transfer from ATGD and ATSN to ATBK • Removed NX3L1T3157GW,125 20111109 • Product data sheet - NX3L1T3157 v.8 Legal pages updated. NX3L1T3157 v.8 20110727 Product data sheet - NX3L1T3157 v.7 NX3L1T3157 v.7 20100121 Product data sheet - NX3L1T3157 v.6 NX3L1T3157 v.6 20090415 Product data sheet - NX3L1T3157 v.5 NX3L1T3157 v.5 20080728 Product data sheet - NX3L1T3157 v.4 NX3L1T3157 v.4 20080718 Product data sheet - NX3L1T3157 v.3 NX3L1T3157 v.3 20080408 Product data sheet - NX3L1T3157 v.2 NX3L1T3157 v.2 20080306 Product data sheet - NX3L1T3157 v.1 NX3L1T3157 v.1 20080103 Product data sheet - - NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 18 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 15. Legal information 15.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 15.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 15.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. NX3L1T3157 Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 19 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. 15.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com NX3L1T3157 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 9.2 — 11 December 2019 © NXP B.V. 2019. All rights reserved. 20 of 21 NX3L1T3157 NXP Semiconductors Low-ohmic single-pole double-throw analog switch 17. Contents 1 2 3 4 4.1 5 6 6.1 6.2 7 8 9 10 10.1 10.2 10.3 11 11.1 11.2 11.3 12 13 14 15 15.1 15.2 15.3 15.4 16 17 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ON resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ON resistance test circuit and graphs. . . . . . . . 8 Dynamic characteristics . . . . . . . . . . . . . . . . . 10 Waveform and test circuits . . . . . . . . . . . . . . . 11 Additional dynamic characteristics . . . . . . . . . 13 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 17 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 18 Legal information. . . . . . . . . . . . . . . . . . . . . . . 19 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 19 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Contact information. . . . . . . . . . . . . . . . . . . . . 20 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2019. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 11 December 2019 Document identifier: NX3L1T3157