BGM1014
MMIC wideband amplifier
Rev. 2 — 19 September 2011
Product data sheet
1. Product profile
1.1 General description
Silicon Monolithic Microwave Integrated Circuit (MMIC) wideband amplifier with internal
matching circuit in a 6-pin SOT363 SMD plastic package.
CAUTION
This device is sensitive to ElectroStatic Discharge (ESD). Therefore care should be taken
during transport and handling.
1.2 Features and benefits
Internally matched to 50
Good output match to 75
32 dB to 34 dB positive sloped gain for Low Noise Block (LNB) application
12.9 dBm saturated load power at 1 GHz
40 dB isolation
1.3 Applications
LNB Intermediate Frequency (IF) amplifiers
Cable systems
General purpose
1.4 Quick reference data
Table 1.
Quick reference data
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VS
DC supply voltage
RF input; AC coupled
-
5
6
V
IS
DC supply current
17
21.0
25
mA
s212
insertion power gain
f = 1 GHz
31.5
32.3
33.0
dB
NF
noise figure
f = 1 GHz
-
4.2
4.3
dB
PL(sat)
saturated load power
f = 1 GHz
12.5
12.9
-
dBm
BGM1014
NXP Semiconductors
MMIC wideband amplifier
2. Pinning information
Table 2.
Pinning
Pin
Description
1
VS
2, 5
GND2
3
RF_OUT
4
GND1
6
RF_IN
Simplified outline
6
5
Symbol
1
4
6
1
2
3
4
3
2, 5
sym062
3. Ordering information
Table 3.
Ordering information
Type number
Package
Name
Description
Version
BGM1014
SC-88
plastic surface mounted package; 6 leads
SOT363
4. Marking
Table 4.
Marking
Type number
Marking code
BGM1014
C5-
5. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
Min
Max
Unit
VS
DC supply voltage
RF input; AC coupled
-
6
V
IS
supply current
-
30
mA
Tsp 90 C
Ptot
total power dissipation
-
200
mW
Tstg
storage temperature
65
+150
C
Tj
junction temperature
-
150
C
PD
maximum drive power
-
10
dBm
6. Recommended operating conditions
Table 6.
BGM1014
Product data sheet
Operating conditions
Symbol
Parameter
Min
Typ
Max
Unit
VS
DC supply voltage
Conditions
4.5
5.0
5.5
V
Tamb
ambient temperature
40
+25
+85
C
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
2 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
7. Thermal characteristics
Table 7.
Thermal characteristics
Symbol
Parameter
Conditions
Typ
Unit
Rth(j-sp)
thermal resistance from junction to solder point
Ptot = 200 mW; Tsp 90 C
300
K/W
8. Characteristics
Table 8.
Characteristics
VS = 5 V; IS = 21.1 mA; Tj = 25 C; measured on demo board; unless otherwise specified.
Symbol Parameter
VS
DC supply voltage
IS
supply current
s212
insertion power gain
Conditions
RF input; AC coupled
s222
input return loss
output return loss
Typ
Max
Unit
-
5
6
V
17
21.0
25
mA
29.0
30.0
31.0
dB
see Figure 4
f = 100 MHz
s112
Min
f = 1 GHz
31.5
32.3
33.0
dB
f = 1.8 GHz
34.0
35.2
36.5
dB
f = 2.2 GHz
33.0
34.1
35.5
dB
f = 2.6 GHz
29.0
30.5
32.0
dB
f = 3 GHz
25.0
26.4
28.0
dB
f = 1 GHz
11
12.2
-
dB
f = 2.2 GHz
7.5
8.8
-
dB
f = 1 GHz
15
18.9
-
dB
f = 2.2 GHz
12
16.7
-
dB
f = 1 GHz
12
16.8
-
dB
f = 2.2 GHz
12
17.7
-
dB
f = 1 GHz
40
42
-
dB
f = 2.2 GHz
35
37
-
dB
f = 1 GHz
-
4.2
4.3
dB
f = 2.2 GHz
-
4.1
4.3
dB
-
2.5
-
GHz
f = 1 GHz
1.5
1.6
-
f = 2.2 GHz
0.9
1.0
-
f = 1 GHz
12.5
12.9
-
f = 2.2 GHz
8.8
9.3
-
dBm
f = 1 GHz
10.5
11.2
-
dBm
f = 2.2 GHz
5.0
5.7
-
dBm
ZL = 50
ZL = 75
s122
NF
isolation
noise figure
see Figure 3
see Figure 7
B
bandwidth
3 dB below flat gain at f = 1 GHz
K
stability factor
see Figure 8
PL(sat)
saturated load power
PL(1dB)
load power at 1 dB gain
compression
BGM1014
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
dBm
© NXP B.V. 2011. All rights reserved.
3 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
Table 8.
Characteristics …continued
VS = 5 V; IS = 21.1 mA; Tj = 25 C; measured on demo board; unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ
Max
Unit
IP3in
f = 1 GHz
13
11.8
-
dBm
f = 2.2 GHz
21
19
-
dBm
IP3out
IM2
input third order intercept point
output third order intercept point f = 1 GHz
second order intermodulation
distortion
19.5
20.5
-
dBm
f = 2.2 GHz
14
15.1
-
dBm
f0 = 1 GHz; PL = 10 dBm
36
37
-
dBc
f0 = 1 GHz; PL = 5 dBm
33
34
-
dBc
90°
1.0
+1
135°
+0.5
0.8
45°
+2
0.6
+0.2
0.4
+5
0.2
100MHz
180°
0
0.2
0.5
1
2
5
10
0°
0
3GHz
−5
−0.2
−135°
−2
−0.5
−45°
−1
−90°
1.0
001aac489
IS = 21.1 mA; VS = 5 V; PD = 35 dBm; Zo = 50
Fig 1.
BGM1014
Product data sheet
Input reflection coefficient (s11); typical values
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
4 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
90°
1.0
+1
135°
+0.5
0.8
45°
+2
0.6
100MHz
+0.2
0.4
+5
0.2
180°
0
0.2
0.5
1
2
5
10
0°
0
3GHz
−5
−0.2
−135°
−2
−0.5
−45°
−1
1.0
−90°
001aac490
IS = 21.1 mA; VS = 5 V; PD = 35 dBm; Zo = 50
Fig 2.
Output reflection coefficient (s22); typical values
001aac491
0
s12 2
(dB)
−10
001aac492
50
s21 2
(dB)
40
(1)
(2)
(3)
−20
30
−30
20
−40
−50
10
0
1000
2000
3000
0
1000
f (MHz)
2000
3000
f (MHz)
IS = 21.1 mA; VS = 5 V; PD = 35 dBm; Zo = 50
PD = 35 dBm; Zo = 50
(1) IS = 25.6 mA; VS = 5.5 V
(2) IS = 21.5 mA; VS = 5 V
(3) IS = 16.6 mA; VS = 4.5 V
Fig 3.
(s122)
Isolation
as a function of frequency;
typical values
BGM1014
Product data sheet
Fig 4.
Insertion gain (s212) as a function of
frequency; typical values
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
5 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
001aac493
20
PL
(dBm)
15
001aac494
15
PL
(dBm)
(1)
(2)
(3)
(1)
(2)
(3)
5
10
5
−5
0
−5
−40
−30
−20
PD (dBm)
−10
−15
−50
f = 1 GHz; Zo = 50
−40
−20
−10
PD (dBm)
f = 2.2 GHz; Zo = 50
(1) VS = 5.5 V
(1) VS = 5.5 V
(2) VS = 5 V
(2) VS = 5 V
(3) VS = 4.5 V
(3) VS = 4.5 V
Fig 5.
−30
Load power as a function of drive power at
1 GHz; typical values
Fig 6.
001aac495
5
Load power as a function of drive power at
2.2 GHz; typical values
001aac496
5
K
NF
(dB)
4
4.5
(1)
(2)
(3)
3
2
4
1
3.5
0
0
500
1000
1500
2000
2500
f (MHz)
0
1000
2000
3000
4000
f (MHz)
Zo = 50
IS = 21.1 mA; VS = 5 V; Zo = 50
(1) VS = 5.5 V
(2) VS = 5 V
(3) VS = 4.5 V
Fig 7.
Noise figure as a function of frequency; typical
values
BGM1014
Product data sheet
Fig 8.
Stability factor as a function of frequency;
typical values
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
6 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
9. Application information
Figure 9 shows a typical application circuit for the BGM1014 MMIC. The device is
internally matched to 50 and therefore does not need any external matching. Good
impedance matching is also achieved with a 75 load. The value of the input and output
DC blocking capacitors C1 and C2 should be not more than 100 pF for applications above
100 MHz. Their values can be used to fine-tune the input and output impedance.
For the RF choke, optimal results are obtained with a good quality chip inductor like the
TDK MLG1608 (0603) or a wire-wound SMD. The value of the inductor can be used to
fine-tune the output impedance.
The RF choke and supply decoupling components should be located as close as possible
to the MMIC.
Ground paths must be as short as possible. The printed-circuit board (PCB) top ground
plane must be as close as possible to the MMIC, and ideally directly beneath it. When
using vias, use at least 3 vias for the top ground plane in order to limit ground path
inductance. Supply decoupling with C3 should be from pin 1 to the same top ground
plane.
VS
VS
1
IN 6
RF in
C3
L1
C2
3
OUT
C1
RF out
BGM1014
SOT363
4
2, 5
GND1
Fig 9.
BGM1014
Product data sheet
GND2
001aac488
Typical application circuit
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
7 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
Figure 10 shows the PCB layout used for the typical application.
30 mm
PH
30 mm
IN
OUT
V+
PH
IC1
C2
C1
L1
IN
OUT
C3
V+
001aab395
Material = FR4; thickness = 0.6 mm; r = 4.6
Fig 10. Printed-circuit board layout and component view for typical application
Table 9.
BGM1014
Product data sheet
List of components used for the typical application
Component
Description
Value
Dimensions
C1, C2
multilayer ceramic chip capacitor
100 pF
0603
C3
multilayer ceramic chip capacitor
22 nF
0603
L1
SMD inductor
100 nH
0603
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
8 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
Table 10. Scattering parameters
VS = 5 V; IS = 21.1 mA; PD = 35 dBm; Zo = 50 ; Tamb = 25 C; measured on demo board.
f
(MHz)
s11
s21
s12
s22
K-factor
Magnitude
(ratio)
Angle
(deg)
Magnitude
(ratio)
Angle
(deg)
Magnitude
(ratio)
Angle
(deg)
Magnitude
(ratio)
Angle
(deg)
100
0.287
16.1
31.28
9.1
0.02196
9.4
0.355
125.5
1.0
200
0.328
3.9
32.14
7.1
0.01734
3.3
0.258
115.3
1.1
400
0.319
28.8
33.57
30.9
0.01287
21.1
0.208
87.6
1.2
600
0.299
50.3
35.61
52.3
0.00969
35.3
0.179
62.1
1.5
800
0.272
68.6
38.05
73.3
0.00808
42.7
0.149
34.7
1.6
1000
0.243
84.7
41.37
95.5
0.00751
44.8
0.113
10.3
1.6
1200
0.225
98.9
45.48
119.1
0.00711
43.7
0.084
8.1
1.6
1400
0.229
106.9
49.78
144.8
0.00792
37.3
0.042
4.5
1.4
1600
0.261
127.8
54.37
173.0
0.00991
37.9
0.042
34.4
1.1
1800
0.317
154.4
57.96
154.4
0.01171
37.2
0.059
41.5
1.0
2000
0.364
167.7
56.65
120.1
0.01302
45.7
0.123
15.9
1.0
2200
0.362
126.7
50.11
85.0
0.01493
60.5
0.130
4.6
1.0
2400
0.354
87.5
41.68
54.6
0.01647
69.8
0.130
32.5
1.0
2600
0.325
47.6
33.47
25.9
0.01878
81.7
0.137
57.1
1.0
2800
0.282
7.7
26.34
1.4
0.02094
94.0
0.135
74.9
1.1
3000
0.231
32.0
20.81
20.3
0.02184
112.2
0.112
104.3
1.2
BGM1014
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
9 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
10. Package outline
Plastic surface-mounted package; 6 leads
SOT363
D
E
B
y
X
A
HE
6
5
v M A
4
Q
pin 1
index
A
A1
1
2
e1
3
bp
c
Lp
w M B
e
detail X
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
A1
max
bp
c
D
E
e
e1
HE
Lp
Q
v
w
y
mm
1.1
0.8
0.1
0.30
0.20
0.25
0.10
2.2
1.8
1.35
1.15
1.3
0.65
2.2
2.0
0.45
0.15
0.25
0.15
0.2
0.2
0.1
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
SOT363
JEITA
SC-88
EUROPEAN
PROJECTION
ISSUE DATE
04-11-08
06-03-16
Fig 11. Package outline SOT363 (SC-88)
BGM1014
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
10 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
11. Revision history
Table 11.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
BGM1014 v.2
20110919
Product data sheet
-
BGM1014 v.1
Modifications:
BGM1014 v.1
(9370 750 14499)
BGM1014
Product data sheet
•
The format of this data sheet has been redesigned to comply with the new identity
guidelines of NXP Semiconductors.
•
•
Legal texts have been adapted to the new company name where appropriate.
Package outline drawings have been updated to the latest version.
20050311
Product data sheet
-
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
-
© NXP B.V. 2011. All rights reserved.
11 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
12. Legal information
12.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
12.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
12.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
BGM1014
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
12 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
12.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
13. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
BGM1014
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 September 2011
© NXP B.V. 2011. All rights reserved.
13 of 14
BGM1014
NXP Semiconductors
MMIC wideband amplifier
14. Contents
1
1.1
1.2
1.3
1.4
2
3
4
5
6
7
8
9
10
11
12
12.1
12.2
12.3
12.4
13
14
Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General description . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick reference data . . . . . . . . . . . . . . . . . . . . 1
Pinning information . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 2
Recommended operating conditions. . . . . . . . 2
Thermal characteristics . . . . . . . . . . . . . . . . . . 3
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Application information. . . . . . . . . . . . . . . . . . . 7
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 11
Legal information. . . . . . . . . . . . . . . . . . . . . . . 12
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 12
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Contact information. . . . . . . . . . . . . . . . . . . . . 13
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 19 September 2011
Document identifier: BGM1014
工商网监
湘ICP备2023018690号
