Datasheet
P89LPC933/934/935/936
8-Bit Microcontroller with Accelerated Two-Clock 80C51 Core
4 kB/8 kB/16 kB 3 V Byte-Erasable Flash with 8-Bit ADCs
The P89LPC933/934/935/936 is a single-chip microcontroller, available in low cost packages,
based on a high performance processor architecture that executes instructions in two to four
clocks, six times the rate of standard 80C51 devices. Many system-level functions have been
incorporated into the P89LPC933/934/935/936 in order to reduce component count, board space,
and system cost.
Rochester Electronics
Manufactured Components
Rochester branded components are
manufactured using either die/wafers
purchased from the original suppliers
or Rochester wafers recreated from the
original IP. All re-creations are done with
the approval of the Original Component
Manufacturer (OCM).
Parts are tested using original factory
test programs or Rochester developed
test solutions to guarantee product
meets or exceeds the OCM data sheet.
Quality Overview
• ISO-9001
• AS9120 certification
• Qualified Manufacturers List (QML) MIL-PRF-35835
• Class Q Military
• Class V Space Level
• Qualified Suppliers List of Distributors (QSLD)
• Rochester is a critical supplier to DLA and
meets all industry and DLA standards.
Rochester Electronics, LLC is committed to supplying
products that satisfy customer expectations for
quality and are equal to those originally supplied by
industry manufacturers.
The original manufacturer’s datasheet accompanying this document reflects the performance
and specifications of the Rochester manufactured version of this device. Rochester Electronics
guarantees the performance of its semiconductor products to the original OCM specifications.
‘Typical’ values are for reference purposes only. Certain minimum or maximum ratings may be
based on product characterization, design, simulation, or sample testing.
FOR REFERENCE ONLY
© 2018 Rochester Electronics, LLC. All Rights Reserved 10112018
To learn more, please visit www.rocelec.com
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs
Rev. 8 — 12 January 2011
Product data sheet
1. General description
The P89LPC933/934/935/936 is a single-chip microcontroller, available in low cost
packages, based on a high performance processor architecture that executes instructions
in two to four clocks, six times the rate of standard 80C51 devices. Many system-level
functions have been incorporated into the P89LPC933/934/935/936 in order to reduce
component count, board space, and system cost.
2. Features and benefits
2.1 Principal features
4 kB/8 kB/16 kB byte-erasable flash code memory organized into 1 kB/2 kB sectors
and 64-byte pages. Single-byte erasing allows any byte(s) to be used as non-volatile
data storage.
256-byte RAM data memory. Both the P89LPC935 and P89LPC936 also include a
512-byte auxiliary on-chip RAM.
512-byte customer data EEPROM on chip allows serialization of devices, storage of
setup parameters, etc. (P89LPC935/936).
Dual 4-input multiplexed 8-bit A/D converters/DAC outputs (P89LPC935/936, single
A/D on P89LPC933/934).Two analog comparators with selectable inputs and
reference source.
Two 16-bit counter/timers (each may be configured to toggle a port output upon timer
overflow or to become a PWM output) and a 23-bit system timer that can also be used
as an RTC.
Enhanced UART with fractional baud rate generator, break detect, framing error
detection, and automatic address detection; 400 kHz byte-wide I2C-bus
communication port and SPI communication port.
Capture/Compare Unit (CCU) provides PWM, input capture, and output compare
functions (P89LPC935/936).
High-accuracy internal RC oscillator option allows operation without external oscillator
components. The RC oscillator option is selectable and fine tunable.
2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or
driven to 5.5 V).
28-pin TSSOP, PLCC, and HVQFN packages with 23 I/O pins minimum and up to 26
I/O pins while using on-chip oscillator and reset options.
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
2.2 Additional features
A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns
for all instructions except multiply and divide when executing at 18 MHz. This is six
times the performance of the standard 80C51 running at the same clock frequency. A
lower clock frequency for the same performance results in power savings and reduced
EMI.
Serial flash In-Circuit Programming (ICP) allows simple production coding with
commercial EPROM programmers. Flash security bits prevent reading of sensitive
application programs.
Serial flash In-System Programming (ISP) allows coding while the device is mounted
in the end application.
In-Application Programming (IAP) of the flash code memory. This allows changing the
code in a running application.
Watchdog timer with separate on-chip oscillator, requiring no external components.
The watchdog prescaler is selectable from eight values.
Low voltage reset (brownout detect) allows a graceful system shutdown when power
fails. May optionally be configured as an interrupt.
Idle and two different power-down reduced power modes. Improved wake-up from
Power-down mode (a LOW interrupt input starts execution). Typical power-down
current is 1 A (total power-down with voltage comparators disabled).
Active-LOW reset. On-chip power-on reset allows operation without external reset
components. A reset counter and reset glitch suppression circuitry prevent spurious
and incomplete resets. A software reset function is also available.
Configurable on-chip oscillator with frequency range options selected by user
programmed flash configuration bits. Oscillator options support frequencies from
20 kHz to the maximum operating frequency of 18 MHz.
Oscillator fail detect. The watchdog timer has a separate fully on-chip oscillator
allowing it to perform an oscillator fail detect function.
Programmable port output configuration options: quasi-bidirectional, open drain,
push-pull, input-only.
Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value of
the pins match or do not match a programmable pattern.
LED drive capability (20 mA) on all port pins. A maximum limit is specified for the
entire chip.
Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns
minimum ramp times.
Only power and ground connections are required to operate the
P89LPC933/934/935/936 when internal reset option is selected.
Four interrupt priority levels.
Eight keypad interrupt inputs, plus two additional external interrupt inputs.
Schmitt trigger port inputs.
Second data pointer.
Emulation support.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
2 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
3. Product comparison overview
Table 1 highlights the differences between the four devices. For a complete list of device
features please see Section 2 “Features and benefits”.
Table 1.
Product comparison overview
Device
Flash memory Sector size
ADC1
ADC0
CCU
Data EEPROM
P89LPC933
4 kB
1 kB
X
-
-
-
P89LPC934
8 kB
1 kB
X
-
-
-
P89LPC935
8 kB
1 kB
X
X
X
X
P89LPC936
16 kB
2 kB
X
X
X
X
4. Ordering information
Table 2.
Ordering information
Type number
Package
Name
Description
Version
P89LPC935FA
PLCC28
plastic leaded chip carrier; 28 leads
SOT261-2
P89LPC933HDH
TSSOP28
plastic thin shrink small outline
package; 28 leads; body width 4.4 mm
SOT361-1
HVQFN28
plastic thermal enhanced very thin
quad flat package; no leads;
28 terminals; body 6 6 0.85 mm
SOT788-1
P89LPC933FDH
P89LPC934FDH
P89LPC935FDH
P89LPC936FDH
P89LPC935FHN
4.1 Ordering options
Table 3.
Ordering options
Type number
Flash memory
Temperature range
P89LPC933HDH
4 kB
40 C to +125 C
P89LPC933FDH
4 kB
40 C to +85 C
P89LPC935FA
8 kB
Frequency
0 MHz to 18 MHz
P89LPC934FDH
P89LPC935FDH
P89LPC935FHN
P89LPC936FDH
P89LPC933_934_935_936
Product data sheet
16 kB
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
3 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
5. Block diagram
P89LPC933/934/935/936
Fig 1.
Block diagram
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
4 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
6. Pinning information
6.1 Pinning
P89LPC933HDH
P89LPC933FDH
P89LPC934FDH
Fig 2.
P89LPC933/934 TSSOP28 pin configuration
P89LPC935FDH
P89LPC936FDH
Fig 3.
P89LPC933_934_935_936
Product data sheet
P89LPC935/936 TSSOP28 pin configuration
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
5 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
P89LPC935FA
Fig 4.
P89LPC935 PLCC28 pin configuration
P89LPC935FHN
Fig 5.
P89LPC933_934_935_936
Product data sheet
P89LPC935 HVQFN28 pin configuration
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
6 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
6.2 Pin description
Table 4.
Pin description
Symbol
Pin
Type
Description
I/O
Port 0: Port 0 is an 8-bit I/O port with a user-configurable output type.
During reset Port 0 latches are configured in the input only mode with the
internal pull-up disabled. The operation of Port 0 pins as inputs and
outputs depends upon the port configuration selected. Each port pin is
configured independently. Refer to Section 8.13.1 “Port configurations”
and Table 11 “Static characteristics” for details.
TSSOP28, HVQFN28
PLCC28
P0.0 to P0.7
The Keypad Interrupt feature operates with Port 0 pins.
All pins have Schmitt trigger inputs.
Port 0 also provides various special functions as described below:
P0.0/CMP2/
KBI0/AD01
P0.1/CIN2B/
KBI1/AD10
P0.2/CIN2A/
KBI2/AD11
P0.3/CIN1B/
KBI3/AD12
P0.4/CIN1A/
KBI4/DAC1/
AD13
3
26
25
24
23
P0.5/
CMPREF/
KBI5
22
P0.6/CMP1/
KBI6
20
P0.7/T1/
KBI7
19
P89LPC933_934_935_936
Product data sheet
27
22
21
20
19
18
16
15
I/O
P0.0 — Port 0 bit 0.
O
CMP2 — Comparator 2 output.
I
KBI0 — Keyboard input 0.
I
AD01 — ADC0 channel 1 analog input. (P89LPC935/936)
I/O
P0.1 — Port 0 bit 1.
I
CIN2B — Comparator 2 positive input B.
I
KBI1 — Keyboard input 1.
I
AD10 — ADC1 channel 0 analog input.
I/O
P0.2 — Port 0 bit 2.
I
CIN2A — Comparator 2 positive input A.
I
KBI2 — Keyboard input 2.
I
AD11 — ADC1 channel 1 analog input.
I/O
P0.3 — Port 0 bit 3.
I
CIN1B — Comparator 1 positive input B.
I
KBI3 — Keyboard input 3.
I
AD12 — ADC1 channel 2 analog input.
I/O
P0.4 — Port 0 bit 4.
I
CIN1A — Comparator 1 positive input A.
I
KBI4 — Keyboard input 4.
O
DAC1 — Digital-to-analog converter output 1.
I
AD13 — ADC1 channel 3 analog input.
I/O
P0.5 — Port 0 bit 5.
I
CMPREF — Comparator reference (negative) input.
I
KBI5 — Keyboard input 5.
I/O
P0.6 — Port 0 bit 6.
O
CMP1 — Comparator 1 output.
I
KBI6 — Keyboard input 6.
I/O
P0.7 — Port 0 bit 7.
I/O
T1 — Timer/counter 1 external count input or overflow output.
I
KBI7 — Keyboard input 7.
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
7 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 4.
Pin description
Symbol
Pin
Type
Description
TSSOP28, HVQFN28
PLCC28
I/O, I [1] Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type,
except for three pins as noted below. During reset Port 1 latches are
configured in the input only mode with the internal pull-up disabled. The
operation of the configurable Port 1 pins as inputs and outputs depends
upon the port configuration selected. Each of the configurable port pins
are programmed independently. Refer to Section 8.13.1 “Port
configurations” and Table 11 “Static characteristics” for details. P1.2 and
P1.3 are open drain when used as outputs. P1.5 is input only.
P1.0 to P1.7
All pins have Schmitt trigger inputs.
Port 1 also provides various special functions as described below:
P1.0/TXD
18
14
I/O
P1.0 — Port 1 bit 0.
O
TXD — Transmitter output for the serial port.
P1.1/RXD
17
13
I/O
P1.1 — Port 1 bit 1.
I
RXD — Receiver input for the serial port.
I/O
P1.2 — Port 1 bit 2 (open-drain when used as output).
I/O
T0 — Timer/counter 0 external count input or overflow output (open-drain
when used as output).
I/O
SCL — I2C serial clock input/output.
I/O
P1.3 — Port 1 bit 3 (open-drain when used as output).
I
INT0 — External interrupt 0 input.
I/O
SDA — I2C serial data input/output.
I
P1.4 — Port 1 bit 4.
I
INT1 — External interrupt 1 input.
I
P1.5 — Port 1 bit 5 (input only).
I
RST — External reset input during power-on or if selected via UCFG1.
When functioning as a reset input, a LOW on this pin resets the
microcontroller, causing I/O ports and peripherals to take on their default
states, and the processor begins execution at address 0. Also used during
a power-on sequence to force ISP mode. When using an oscillator
frequency above 12 MHz, the reset input function of P1.5 must be
enabled. An external circuit is required to hold the device in reset at
power-up until VDD has reached its specified level. When system
power is removed VDD will fall below the minimum specified
operating voltage. When using an oscillator frequency above
12 MHz, in some applications, an external brownout detect circuit
may be required to hold the device in reset when VDD falls below the
minimum specified operating voltage.
P1.2/T0/SCL 12
P1.3/INT0/
SDA
11
8
7
P1.4/INT1
10
6
P1.5/RST
6
2
P1.6/OCB
5
1
I/O
P1.6 — Port 1 bit 6.
O
OCB — Output Compare B. (P89LPC935/936)
P1.7/OCC/
AD00
4
28
I/O
P1.7 — Port 1 bit 7.
O
OCC — Output Compare C. (P89LPC935/936)
I
AD00 — ADC0 channel 0 analog input. (P89LPC935/936)
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
8 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 4.
Pin description
Symbol
Pin
Type
Description
I/O
Port 2: Port 2 is an 8-bit I/O port with a user-configurable output type.
During reset Port 2 latches are configured in the input only mode with the
internal pull-up disabled. The operation of Port 2 pins as inputs and
outputs depends upon the port configuration selected. Each port pin is
configured independently. Refer to Section 8.13.1 “Port configurations”
and Table 11 “Static characteristics” for details.
TSSOP28, HVQFN28
PLCC28
P2.0 to P2.7
All pins have Schmitt trigger inputs.
Port 2 also provides various special functions as described below:
P2.0/ICB/
DAC0/AD03
P2.1/OCD/
AD02
P2.2/MOSI
P2.3/MISO
1
2
13
14
25
26
9
10
P2.4/SS
15
11
P2.5/
SPICLK
16
12
P2.6/OCA
27
P2.7/ICA
28
P89LPC933_934_935_936
Product data sheet
23
24
I/O
P2.0 — Port 2 bit 0.
I
ICB — Input Capture B. (P89LPC935/936)
I
DAC0 — Digital-to-analog converter output.
I
AD03 — ADC0 channel 3 analog input. (P89LPC935/936)
I/O
P2.1 — Port 2 bit 1.
O
OCD — Output Compare D. (P89LPC935/936)
I
AD02 — ADC0 channel 2 analog input. (P89LPC935/936)
I/O
P2.2 — Port 2 bit 2.
I/O
MOSI — SPI master out slave in. When configured as master, this pin is
output; when configured as slave, this pin is input.
I/O
P2.3 — Port 2 bit 3.
I/O
MISO — When configured as master, this pin is input, when configured as
slave, this pin is output.
I/O
P2.4 — Port 2 bit 4.
I
SS — SPI Slave select.
I/O
P2.5 — Port 2 bit 5.
I/O
SPICLK — SPI clock. When configured as master, this pin is output; when
configured as slave, this pin is input.
I/O
P2.6 — Port 2 bit 6.
O
OCA — Output Compare A. (P89LPC935/936)
I/O
P2.7 — Port 2 bit 7.
I
ICA — Input Capture A. (P89LPC935/936)
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
9 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 4.
Pin description
Symbol
Pin
Type
Description
I/O
Port 3: Port 3 is a 2-bit I/O port with a user-configurable output type.
During reset Port 3 latches are configured in the input only mode with the
internal pull-up disabled. The operation of Port 3 pins as inputs and
outputs depends upon the port configuration selected. Each port pin is
configured independently. Refer to Section 8.13.1 “Port configurations”
and Table 11 “Static characteristics” for details.
TSSOP28, HVQFN28
PLCC28
P3.0 to P3.1
All pins have Schmitt trigger inputs.
Port 3 also provides various special functions as described below:
P3.0/XTAL2/ 9
CLKOUT
P3.1/XTAL1
8
5
4
I/O
P3.0 — Port 3 bit 0.
O
XTAL2 — Output from the oscillator amplifier (when a crystal oscillator
option is selected via the flash configuration.
O
CLKOUT — CPU clock divided by 2 when enabled via SFR bit (ENCLK TRIM.6). It can be used if the CPU clock is the internal RC oscillator,
watchdog oscillator or external clock input, except when XTAL1/XTAL2
are used to generate clock source for the RTC/system timer.
I/O
P3.1 — Port 3 bit 1.
I
XTAL1 — Input to the oscillator circuit and internal clock generator circuits
(when selected via the flash configuration). It can be a port pin if internal
RC oscillator or watchdog oscillator is used as the CPU clock source, and
if XTAL1/XTAL2 are not used to generate the clock for the RTC/system
timer.
VSS
7
3
I
Ground: 0 V reference.
VDD
21
17
I
Power supply: This is the power supply voltage for normal operation as
well as Idle and Power-down modes.
[1]
Input/output for P1.0 to P1.4, P1.6, P1.7. Input for P1.5.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
10 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
7. Logic symbols
P89LPC933
P89LPC934
Fig 6.
P89LPC933/934 logic symbol
P89LPC935
P89LPC936
Fig 7.
P89LPC935/936 logic symbol
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
11 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8. Functional description
Remark: Please refer to the P89LPC933/934/935/936
functional description.
for a more detailed
8.1 Special function registers
Remark: SFR accesses are restricted in the following ways:
• User must not attempt to access any SFR locations not defined.
• Accesses to any defined SFR locations must be strictly for the functions for the SFRs.
• SFR bits labeled ‘-’, logic 0 or logic 1 can only be written and read as follows:
– ‘-’ Unless otherwise specified, must be written with logic 0, but can return any
value when read (even if it was written with logic 0). It is a reserved bit and may be
used in future derivatives.
– Logic 0 must be written with logic 0, and will return a logic 0 when read.
– Logic 1 must be written with logic 1, and will return a logic 1 when read.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
12 of 77
Description
Accumulator
A/D control register 0
A/D control register 1
A/D input select
A/D mode register A
Name
ACC*
P89LPC933_934_935_936
Product data sheet
ADCON0
ADCON1
ADINS
ADMODA
Rev. 8 — 12 January 2011
A/D_1 boundary high register
A/D_1 boundary low register
A/D_1 data register 0
A/D_1 data register 1
A/D_1 data register 2
A/D_1 data register 3
Auxiliary function register
AD0DAT3
AD1BH
AD1BL
AD1DAT0
AD1DAT1
AD1DAT2
AD1DAT3
AUXR1
All information provided in this document is subject to legal disclaimers.
Data pointer (2 bytes)
DPTR
FMADRH
Program flash address high
Data pointer low
CPU clock divide-by-M
control
DIVM
Data pointer high
Comparator 2 control register
CMP2
DPL
Baud rate generator control
Comparator 1 control register
Baud rate generator rate high
BRGR1
CMP1
Baud rate generator rate low
BRGR0
BRGCON
B register
B*
DPH
A2H
F5H
D7H
D6H
D5H
BCH
C4H
F4H
A1H
E7H
82H
83H
95H
ADH
ACH
BDH
BFH
BEH
F0H
Bit address
A/D mode register B
A/D_0 data register 3
ADMODB
C0H
A3H
97H
8EH
E0H
Bit address
-
-
-
F7
CLKLP
CLK2
BNDI1
ADI13
ENBI1
-
E7
-
-
-
F6
EBRR
CLK1
BURST1
ADI12
ENADCI
1
-
E6
CE2
CE1
-
F5
ENT1
CLK0
SCC1
ADI11
TMM1
-
E5
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC933/934
Table 5.
CP2
CP1
-
F4
ENT0
-
SCAN1
ADI10
EDGE1
-
E4
-
-
ENADC1
ENADC0
E2
CN2
CN1
-
F3
SRST
OE2
OE1
-
F2
0
ENDAC1 ENDAC0
-
-
ADCI1
-
E3
CO2
CO1
SBRGS
F1
-
BSA1
-
-
ADCS11
-
E1
00
00
Hex
CMF2
CMF1
BRGEN
F0
DPS
-
-
-
xxxx xx00
xx00 0000
xx00 0000
00[2]
00[1]
00[1]
00
00
00
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
00[1][2]
00
0000 0000
0000 0000
00
0000 00x0
00[2]
0000 0000
00[1]
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
000x 0000
0000 0000
0000 0000
00
00
00
00
00
FF
00
00
00
00
0000 0000
0000 0000
0000 0000
Binary
Reset value
ADCS10 00
-
E0
LSB
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
© NXP B.V. 2011. All rights reserved.
13 of 77
E4H
E4H
Description
Program flash address low
Program flash control (Read)
Program flash control (Write)
Name
FMADRL
FMCON
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
Interrupt priority 1
Interrupt priority 1 high
IP1*
IP1H
Interrupt priority 0 high
IP0H
ICRBL
Interrupt priority 0
Input capture B register low
ICRBH
IP0*
Input capture B register high
ICRAL
Interrupt enable 1
Input capture A register low
ICRAH
IEN1*
Input capture A register high
I2STAT
Interrupt enable 0
D9H
I2C status register
I2SCLL
IEN0*
DCH
Serial clock generator/SCL
duty cycle register low
I2SCLH
BUSY
BF
Bit address
F7H
F8H
Bit address
B7H
PADH
PAD
FF
-
-
EAD
EF
E8H
EA
AF
STA.4
-
DF
I2ADR.6
A8H
B8H
-
-
-
HVA
HVE
SV
OI
LSB
PSTH
PST
FE
PWDRT
H
PWDRT
BE
EST
EE
EWDRT
AE
STA.3
I2EN
DE
I2ADR.5
-
-
FD
PBOH
PBO
BD
-
ED
EBO
AD
STA.2
STA
DD
I2ADR.4
-
-
FC
PSH/
PSRH
PS/PSR
BC
-
EC
ES/ESR
AC
STA.1
STO
DC
I2ADR.3
PSPIH
PSPI
FB
PT1H
PT1
BB
ESPI
EB
ET1
AB
STA.0
SI
DB
I2ADR.2
PCH
PC
FA
PX1H
PX1
BA
EC
EA
EX1
AA
0
AA
DA
I2ADR.1
PKBIH
PKBI
F9
PT0H
PT0
B9
EKBI
E9
ET0
A9
0
-
D9
I2ADR.0
PI2CH
PI2C
F8
PX0H
PX0
B8
EI2C
E8
EX0
A8
0
CRSEL
D8
GC
FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD.
7
6
5
4
3
2
1
0
Bit address
Bit address
AEH
AFH
AAH
ABH
DDH
Serial clock generator/SCL
duty cycle register high
I2DAT
DAH
D8H
Bit address
I2C
data register
I2C control register
I2C slave address register
I2ADR
I2CON*
E5H
DBH
Program flash data
FMDATA
E6H
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC933/934
Table 5.
00x0 0000
00x0 0000
00[3]
x000 0000
00[3]
x000 0000
00[3]
00x0 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
1111 1000
0000 0000
0000 0000
x000 00x0
0000 0000
0000 0000
0111 0000
0000 0000
Binary
00[3]
00[3]
00
00
00
00
00
F8
00
00
00
00
00
70
00
Hex
Reset value
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
© NXP B.V. 2011. All rights reserved.
14 of 77
P89LPC933_934_935_936
Product data sheet
Keypad interrupt mask
register
Keypad pattern register
Port 0
KBMASK
KBPATN
P0*
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
Port 3 output mode 1
Port 3 output mode 2
Power control register
Power control register A
P3M1
P3M2
PCON
PCONA
B5H
87H
B2H
B1H
A5H
A4H
92H
91H
D1H
DFH
F6H
D0H
Bit address
Real-time clock control
Port 2 output mode 2
P2M2
RTCCON
Port 2 output mode 1
P2M1
Reset source register
Port 1 output mode 2
P1M2
Port 0 digital input disable
Port 1 output mode 1
P1M1
85H
84H
LSB
-
-
(P1M1.4) (P1M1.3) (P1M1.2) (P1M1.1) (P1M1.0)
RTCF
-
-
CY
D7
RTCPD
SMOD1
RTCS1
-
-
AC
D6
-
SMOD0
BOI
RS1
D4
ADPD
RS0
D3
I2PD
GF1
-
OV
D2
SPPD
GF0
-
-
F1
D1
SPD
PMOD1
RTCS0
BOF
-
POF
-
R_BK
-
R_WD
ERTC
R_SF
RTCEN
R_EX
-
P
D0
-
PMOD0
(P3M1.1) (P3M1.0)
PT0AD.5 PT0AD.4 PT0AD.3 PT0AD.2 PT0AD.1
F0
D5
VCPD
BOPD
-
-
60[3][5]
00
011x xx00
[4]
xx00 000x
0000 0000
0000 0000
00[3]
00
0000 0000
00
xxxx xx00
-
-
xxxx xx11
-
-
(P3M2.1) (P3M2.0) 00[3]
-
-
03[3]
-
0000 0000
(P2M2.7) (P2M2.6) (P2M2.5) (P2M2.4) (P2M2.3) (P2M2.2) (P2M2.1) (P2M2.0) 00[3]
(P2M1.7) (P2M1.6) (P2M1.5) (P2M1.4) (P2M1.3) (P2M1.2) (P2M1.1) (P2M1.0)
(P1M2.7) (P1M2.6)
(P1M1.7) (P1M1.6)
1111 1111
[3]
[3]
[3]
[3]
1111 1111
00x0 xx00
FF
0000 0000
xxxx xx00
00[3]
00
Binary
Hex
FF[3]
XTAL2
B0
-
A0
TXD
90
CMP2
/KB0
80
KBIF
11x1 xx11
XTAL1
B1
-
A1
RXD
91
CIN2B
/KB1
81
PATN
_SEL
(P1M2.4) (P1M2.3) (P1M2.2) (P1M2.1) (P1M2.0) 00[3]
-
B2
MOSI
A2
T0/SCL
92
CIN2A
/KB2
82
-
0000 0000
-
B3
MISO
A3
INT0/
SDA
93
CIN1B
/KB3
83
-
D3[3]
-
B4
SS
A4
INT1
94
CIN1A
/KB4
84
-
1111 1111
-
B5
SPICLK
A5
RST
95
CMPREF
/KB5
85
-
(P0M2.7) (P0M2.6) (P0M2.5) (P0M2.4) (P0M2.3) (P0M2.2) (P0M2.1) (P0M2.0) 00[3]
-
B6
-
A6
-
96
CMP1
/KB6
86
-
Reset value
(P0M1.7) (P0M1.6) (P0M1.5) (P0M1.4) (P0M1.3) (P0M1.2) (P0M1.1) (P0M1.0) FF[3]
-
B7
Bit address
B0H
-
A7
-
97
T1/KB7
87
-
A0H
RSTSRC
Port 0 output mode 2
P0M2
90H
Bit address
PT0AD
Port 0 output mode 1
P0M1
80H
Bit address
Program status word
Port 3
P3*
93H
86H
94H
Bit address
PSW*
Port 2
P2*
Port 1
Keypad control register
KBCON
P1*
Description
Name
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC933/934
Table 5.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
© NXP B.V. 2011. All rights reserved.
15 of 77
P89LPC933_934_935_936
Product data sheet
Serial port address enable
Serial Port data buffer register
SADEN
SBUF
99H
B9H
A9H
D3H
D2H
Timer 0 and 1 control
Timer 0 high
Timer 1 high
Timer 0 low
Timer 1 low
Timer 0 and 1 mode
Internal oscillator trim register
Watchdog control register
TCON*
TH0
TH1
Rev. 8 — 12 January 2011
TL0
TL1
All information provided in this document is subject to legal disclaimers.
TMOD
TRIM
WDCON
A7H
96H
89H
8BH
8AH
8DH
8CH
88H
PRE2
RCCLK
T1GATE
TF1
8F
E3H
SPIF
SSIG
Bit address
Timer 0 and 1 auxiliary mode
TAMOD
E1H
E2H
81H
SM0/FE
DBMOD
-
SPI data register
SPDAT
98H
BAH
9F
8FH
SPI control register
SPI status register
SP
SPSTAT
Stack pointer
SSTAT
SPCTL
Serial port control
Serial port extended status
register
SCON*
Bit address
Real-time clock register low
Serial port address register
SADDR
Real-time clock register high
RTCH
RTCL
Description
Name
PRE1
ENCLK
T1C/T
TR1
8E
-
WCOL
SPEN
INTLO
SM1
9E
PRE0
TRIM.5
T1M1
TF0
8D
-
-
DORD
CIDIS
SM2
9D
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC933/934
Table 5.
-
TRIM.4
T1M0
TR0
8C
T1M2
-
MSTR
DBISEL
REN
9C
-
TRIM.3
T0GATE
IE1
8B
-
-
CPOL
FE
TB8
9B
WDRUN
TRIM.2
T0C/T
IT1
8A
-
-
CPHA
BR
RB8
9A
WDTOF
TRIM.1
T0M1
IE0
89
-
-
SPR1
OE
TI
99
WDCLK
TRIM.0
T0M0
IT0
88
T0M2
-
SPR0
STINT
RI
98
LSB
0000 0000
00[5]
00
00
00
00
00
00
00
00
00
04
07
00
00
xx
00
[7] [5]
[6] [5]
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
xxx0 xxx0
0000 0000
00xx xxxx
0000 0100
0000 0111
0000 0000
0000 0000
xxxx xxxx
0000 0000
0000 0000
0000 0000
00[5]
00
Binary
Hex
Reset value
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
© NXP B.V. 2011. All rights reserved.
16 of 77
Description
Watchdog load
Watchdog feed 1
Watchdog feed 2
Name
WDL
WFEED1
WFEED2
P89LPC933_934_935_936
Product data sheet
BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable.
All ports are in input only (high-impedance) state after power-up.
The RSTSRC register reflects the cause of the P89LPC933/934/935/936 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset
value is xx11 0000.
The only reset source that affects these SFRs is power-on reset.
On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register.
After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset.
Other resets will not affect WDTOF.
[3]
[4]
[5]
[6]
[7]
1111 1111
Binary
[2]
FF
Hex
Unimplemented bits in SFRs (labeled ’-’) are X (unknown) at all times. Unless otherwise specified, ones should not be written to these bits since they may be used for other
purposes in future derivatives. The reset values shown for these bits are logic 0s although they are unknown when read.
LSB
Reset value
[1]
C3H
C2H
C1H
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC933/934
Table 5.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
17 of 77
Description
Accumulator
A/D control register 0
A/D control register 1
A/D input select
A/D mode register A
A/D mode register B
A/D_0 boundary high register
A/D_0 boundary low register
A/D_0 data register 0
A/D_0 data register 1
A/D_0 data register 2
A/D_0 data register 3
A/D_1 boundary high register
A/D_1 boundary low register
A/D_1 data register 0
A/D_1 data register 1
A/D_1 data register 2
A/D_1 data register 3
Auxiliary function register
Name
ACC*
ADCON0
P89LPC933_934_935_936
Product data sheet
ADCON1
ADINS
ADMODA
ADMODB
AD0BH
AD0BL
AD0DAT0
AD0DAT1
AD0DAT2
AD0DAT3
AD1BH
AD1BL
AD1DAT0
AD1DAT1
Rev. 8 — 12 January 2011
AD1DAT2
AD1DAT3
All information provided in this document is subject to legal disclaimers.
AUXR1
B register
Baud rate generator rate low
Baud rate generator rate high
Baud rate generator control
Capture compare A control
register
B*
BRGR0[2]
BRGR1[2]
BRGCON
CCCRA
EAH
BDH
BFH
BEH
F0H
Bit address
A2H
F5H
D7H
D6H
D5H
BCH
C4H
F4H
C7H
C6H
C5H
A6H
BBH
A1H
C0H
A3H
97H
8EH
E0H
Bit address
ICECA2
-
F7
CLKLP
CLK2
BNDI1
ADI13
ENBI1
ENBI0
E7
ICECA1
-
F6
EBRR
CLK1
BURST1
ADI12
ENADCI
1
ENADCI
0
E6
ICECA0
-
F5
ENT1
CLK0
SCC1
ADI11
TMM1
TMM0
E5
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC935/936
Table 6.
ICESA
-
F4
ENT0
-
SCAN1
ADI10
EDGE1
EDGE0
E4
ICNFA
-
F3
SRST
E1
BURST0
ADI02
ENADC1
FCOA
-
F2
0
OCMA1
SBRGS
F1
-
BSA1
SCC0
ADI01
ADCS11
ENADC0 ADCS01
E2
ENDAC1 ENDAC0
BNDI0
ADI03
ADCI1
ADCI0
E3
00
Hex
OCMA0
BRGEN
F0
DPS
BSA0
SCAN0
ADI00
0000 0000
xxxx xx00
00[2]
00
0000 0000
0000 0000
0000 0000
0000 00x0
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
000x 0000
0000 0000
0000 0000
0000 0000
00
00
00
00
00
00
00
00
00
FF
00
00
00
00
00
FF
00
00
00
ADCS10 00
0000 0000
0000 0000
Binary
Reset value
ADCS00 00
E0
LSB
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
© NXP B.V. 2011. All rights reserved.
18 of 77
P89LPC933_934_935_936
Product data sheet
Data EEPROM control
register
Data EEPROM data register
DEECON
DEEDAT
Rev. 8 — 12 January 2011
E4H
E4H
Program flash control (Read)
Program flash control (Write)
FMCON
All information provided in this document is subject to legal disclaimers.
I2C
I2C data register
Serial clock generator/SCL
duty cycle register high
I2CON*
I2DAT
I2SCLH
control register
I2C slave address register
I2ADR
DDH
DAH
D8H
Bit address
E5H
DBH
Program flash data
FMDATA
E6H
Program flash address low
FMADRL
82H
E7H
Data pointer low
Program flash address high
83H
Data pointer high
95H
F3H
F2H
F1H
ADH
ACH
EDH
ECH
EBH
FMADRH
DPL
DPH
Data pointer (2 bytes)
Comparator 2 control register
CMP2
DPTR
Comparator 1 control register
CMP1
CPU clock divide-by-M
control
Capture compare D control
register
CCCRD
DIVM
Capture compare C control
register
CCCRC
Data EEPROM address
register
Capture compare B control
register
CCCRB
DEEADR
Description
Name
-
HVERR
-
-
-
-
ICECB1
-
ECTL1
CE2
CE1
-
-
ICECB0
-
ECTL0
CP2
CP1
-
-
ICESB
HVA
-
CN2
CN1
-
-
ICNFB
HVE
-
OE2
OE1
FCOD
FCOC
FCOB
SV
-
CO2
CO1
OCMD1
OCMC1
OCMB1
LSB
OI
EADR8
CMF2
CMF1
OCMD0
OCMC0
OCMB0
-
DF
I2ADR.6
I2EN
DE
I2ADR.5
STA
DD
I2ADR.4
STO
DC
I2ADR.3
SI
DB
I2ADR.2
AA
DA
I2ADR.1
-
D9
I2ADR.0
CRSEL
D8
GC
FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD.
7
6
5
4
3
2
1
0
BUSY
EEIF
-
-
-
-
ICECB2
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC935/936
Table 6.
xx00 0000
00[3]
00
00
00
00
00
70
00
00
00
00
00
00
0000 0000
x000 00x0
0000 0000
0000 0000
0111 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 1110
xx00 0000
00[3]
0E
xxxx x000
xxxx x000
0000 0000
Binary
00
00
00
Hex
Reset value
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
© NXP B.V. 2011. All rights reserved.
19 of 77
P89LPC933_934_935_936
Product data sheet
AEH
Interrupt priority 0
Interrupt priority 0 high
Interrupt priority 1
Interrupt priority 1 high
Keypad control register
Keypad interrupt mask
register
Keypad pattern register
Output compare A register
high
Output compare A register
low
Output compare B register
high
Output compare B register
low
IP0*
IP0H
IP1*
IP1H
Rev. 8 — 12 January 2011
KBCON
KBMASK
All information provided in this document is subject to legal disclaimers.
KBPATN
OCRAH
OCRAL
OCRBH
OCRBL
FAH
FBH
EEH
EFH
93H
86H
94H
F7H
-
PAEEH
PADEE
FF
Bit address
F8H
-
-
BF
B7H
B8H
Bit address
EADEE
EF
E8H
EA
A8H
AF
STA.4
Bit address
Interrupt enable 1
Interrupt enable 0
IEN1*
IEN0*
Input capture B register low
ICRBL
AFH
AAH
ABH
Bit address
Input capture A register low
Input capture A register high
ICRAH
Input capture B register high
I2C status register
I2STAT
ICRBH
D9H
Serial clock generator/SCL
duty cycle register low
I2SCLL
ICRAL
DCH
Description
Name
-
PSTH
PST
FE
PWDRT
H
PWDRT
BE
EST
EE
EWDRT
AE
STA.3
-
-
-
FD
PBOH
PBO
BD
-
ED
EBO
AD
STA.2
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC935/936
Table 6.
-
PCCUH
PCCU
FC
PSH/
PSRH
PS/PSR
BC
ECCU
EC
ES/ESR
AC
STA.1
-
PSPIH
PSPI
FB
PT1H
PT1
BB
ESPI
EB
ET1
AB
STA.0
-
PCH
PC
FA
PX1H
PX1
BA
EC
EA
EX1
AA
0
PATN
_SEL
PKBIH
PKBI
F9
PT0H
PT0
B9
EKBI
E9
ET0
A9
0
KBIF
PI2CH
PI2C
F8
PX0H
PX0
B8
EI2C
E8
EX0
A8
0
LSB
Binary
xxxx xx00
00
00
00
00
FF
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
00x0 0000
00[3]
00
00x0 0000
00[3]
x000 0000
00[3]
x000 0000
00[3]
00x0 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
1111 1000
0000 0000
00[3]
00[3]
00
00
00
00
00
F8
00
Hex
Reset value
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
© NXP B.V. 2011. All rights reserved.
20 of 77
P89LPC933_934_935_936
Product data sheet
Output compare C register
low
Output compare D register
high
Output compare D register
low
OCRCL
OCRDH
OCRDL
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
Power control register A
Program status word
Port 0 digital input disable
PCONA
PSW*
PT0AD
B5H
87H
B2H
B1H
A5H
A4H
92H
91H
85H
F6H
D0H
Bit address
Power control register
Port 2 output mode 1
P2M1
Port 3 output mode 2
Port 1 output mode 2
P1M2
PCON
Port 1 output mode 1
P1M1
P3M2
Port 0 output mode 2
P0M2
84H
86
-
B6
OCA
A6
OCB
96
CMP1
/KB6
85
-
B5
SPICLK
A5
RST
95
CMPREF
/KB5
84
-
B4
SS
A4
INT1
94
CIN1A
/KB4
83
-
B3
MISO
A3
INT0/
SDA
93
CIN1B
/KB3
82
-
B2
MOSI
A2
T0/SCL
92
CIN2A
/KB2
81
XTAL1
B1
OCD
A1
RXD
91
CIN2B
/KB1
XTAL2
B0
ICB
A0
TXD
90
CMP2
/KB0
80
LSB
00
00
00
00
Hex
0000 0000
11x1 xx11
00x0 xx00
1111 1111
(P1M1.4) (P1M1.3) (P1M1.2) (P1M1.1) (P1M1.0) D3[3]
00[3]
(P2M1.7) (P2M1.6) (P2M1.5) (P2M1.4) (P2M1.3) (P2M1.2) (P2M1.1) (P2M1.0) FF[3]
-
-
-
CY
D7
RTCPD
SMOD1
-
-
-
AC
D6
DEEPD
SMOD0
-
-
RS1
D4
ADPD
BOI
-
-
RS0
D3
I2PD
GF1
-
-
OV
D2
SPPD
GF0
-
-
F1
D1
SPD
PMOD1
-
P
D0
CCUPD
PMOD0
(P3M2.1) (P3M2.0)
00
00
xx00 000x
0000 0000
0000 0000
00[3]
xxxx xx00
00[3]
0000 0000
xxxx xx11
(P3M1.1) (P3M1.0) 03[3]
PT0AD.5 PT0AD.4 PT0AD.3 PT0AD.2 PT0AD.1
F0
D5
VCPD
BOPD
-
-
00
0000 0000
00[3]
(P1M2.4) (P1M2.3) (P1M2.2) (P1M2.1) (P1M2.0)
(P2M2.7) (P2M2.6) (P2M2.5) (P2M2.4) (P2M2.3) (P2M2.2) (P2M2.1) (P2M2.0)
(P1M2.7) (P1M2.6)
(P1M1.7) (P1M1.6)
(P0M2.7) (P0M2.6) (P0M2.5) (P0M2.4) (P0M2.3) (P0M2.2) (P0M2.1) (P0M2.0)
00[3]
1111 1111
[3]
[3]
[3]
[3]
0000 0000
0000 0000
0000 0000
0000 0000
Binary
Reset value
(P0M1.7) (P0M1.6) (P0M1.5) (P0M1.4) (P0M1.3) (P0M1.2) (P0M1.1) (P0M1.0) FF[3]
-
B7
Bit address
B0H
ICA
A0H
A7
Bit address
97
OCC
Port 2 output mode 2
Port 0 output mode 1
P0M1
87
T1/KB7
90H
Port 3 output mode 1
Port 3
P3*
80H
Bit address
P3M1
Port 2
P2*
FEH
FFH
FCH
FDH
Bit address
P2M2
Port 1
P1*
Port 0
Output compare C register
high
OCRCH
P0*
Description
Name
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC935/936
Table 6.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
© NXP B.V. 2011. All rights reserved.
21 of 77
P89LPC933_934_935_936
Product data sheet
Serial port address enable
Serial Port data buffer register
SADDR
SADEN
SBUF
Rev. 8 — 12 January 2011
All information provided in this document is subject to legal disclaimers.
Timer 0 low
Timer 1 low
TL0
TL1
CCU interrupt control register
TICR2
CCU interrupt status encode
register
CCU timer high
TH2
CCU interrupt flag register
Timer 1 high
TH1
TISE2
Timer 0 high
TH0
TIFR2
CCU control register 0
CCU control register 1
TCR21
8BH
8AH
DEH
E9H
C9H
CDH
8DH
8CH
F9H
C8H
88H
-
TOIF2
TOIE2
TCOU2
PLEEN
TF1
8F
E3H
SPIF
SSIG
Bit address
TCR20*
Timer 0 and 1 control
Timer 0 and 1 auxiliary mode
TAMOD
E1H
E2H
81H
SM0/FE
DBMOD
-
SPI data register
SPDAT
98H
BAH
9F
RTCF
-
8FH
SPI control register
SPI status register
SP
SPSTAT
Stack pointer
SSTAT
SPCTL
Serial port control
Serial port extended status
register
SCON*
TCON*
99H
B9H
A9H
D3H
D2H
D1H
DFH
Bit address
Real-time clock register low
Serial port address register
RTCL
Real-time clock control
Real-time clock register high
RTCH
Reset source register
RSTSRC
RTCCON
Description
Name
TOCIE2
C
-
HLTEN
TF0
8D
-
-
DORD
CIDIS
SM2
9D
RTCS0
BOF
-
-
PLLDV.3
ALTAB
IE1
8B
-
-
CPOL
FE
TB8
9B
-
R_BK
-
-
TOCF2A
TOCIE2B TOCIE2A
-
ALTCD
TR0
8C
T1M2
-
MSTR
DBISEL
REN
9C
-
POF
TOCF2D TOCF2C TOCF2B
TOCIE2
D
-
HLTRN
TR1
8E
-
WCOL
SPEN
INTLO
SM1
9E
RTCS1
-
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC935/936
Table 6.
ENCINT.
2
-
-
PLLDV.2
TDIR2
IT1
8A
-
-
CPHA
BR
RB8
9A
-
R_WD
LSB
IT0
88
T0M2
-
SPR0
STINT
RI
98
RTCEN
R_EX
0000 0000
00
00
00
00
04
07
00
00
xx
00
ENCINT.
1
TICF2B
TICIE2B
PLLDV.1
00
00
00
ENCINT. 00
0
TICF2A
TICIE2A 00
00
00
00
PLLDV.0 00
0000 0000
0000 0000
xxxx x000
0000 0x00
0000 0x00
0000 0000
0000 0000
0000 0000
0xxx 0000
0000 0000
0000 0000
xxx0 xxx0
0000 0000
00xx xxxx
0000 0100
0000 0111
0000 0000
0000 0000
xxxx xxxx
0000 0000
0000 0000
0000 0000
00[5]
00
011x xx00
00[5]
[4]
Binary
60[3][5]
Hex
TMOD21 TMOD20 00
IE0
89
-
-
SPR1
OE
TI
99
ERTC
R_SF
Reset value
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
© NXP B.V. 2011. All rights reserved.
22 of 77
Description
CCU timer low
Timer 0 and 1 mode
CCU reload register high
Name
TL2
TMOD
TOR2H
P89LPC933_934_935_936
Product data sheet
-
T1M0
-
T0GATE
-
T0C/T
T0M0
00
00
00
TPCR2H. TPCR2H. 00
1
0
T0M1
On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register.
The only reset source that affects these SFRs is power-on reset.
1111 1111
[7]
FF
[7] [5]
[6] [5]
[6]
WDCLK
TRIM.0
After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset.
Other resets will not affect WDTOF.
WDTOF
TRIM.1
[5]
WDRUN
TRIM.2
The RSTSRC register reflects the cause of the P89LPC933/934/935/936 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset
value is xx11 0000.
-
TRIM.3
BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable.
-
TRIM.4
[4]
PRE0
TRIM.5
[3]
PRE1
ENCLK
All ports are in input only (high-impedance) state after power-up.
PRE2
RCCLK
0000 0000
xxxx xx00
0000 0000
0000 0000
0000 0000
[2]
C3H
-
T1M1
0000 0000
Binary
Unimplemented bits in SFRs (labeled ’-’) are X (unknown) at all times. Unless otherwise specified, ones should not be written to these bits since they may be used for other
purposes in future derivatives. The reset values shown for these bits are logic 0s although they are unknown when read.
Watchdog feed 2
WFEED2
C2H
C1H
A7H
96H
-
T1C/T
00
Hex
TPCR2L. TPCR2L. TPCR2L. TPCR2L. TPCR2L. TPCR2L. TPCR2L. TPCR2L. 00
7
6
5
4
3
2
1
0
-
T1GATE
LSB
Reset value
[1]
Watchdog load
Watchdog feed 1
WDCON
WFEED1
Watchdog control register
TRIM
WDL
Internal oscillator trim register
TPCR2L
CAH
Prescaler control register low
TPCR2H
CEH
CCU reload register low
Prescaler control register high CBH
TOR2L
CFH
89H
CCH
SFR Bit functions and addresses
addr.
MSB
Special function registers - P89LPC935/936
Table 6.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
23 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.2 Enhanced CPU
The P89LPC933/934/935/936 uses an enhanced 80C51 CPU which runs at six times the
speed of standard 80C51 devices. A machine cycle consists of two CPU clock cycles, and
most instructions execute in one or two machine cycles.
8.3 Clocks
8.3.1 Clock definitions
The P89LPC933/934/935/936 device has several internal clocks as defined below:
OSCCLK — Input to the DIVM clock divider. OSCCLK is selected from one of four clock
sources (see Figure 8) and can also be optionally divided to a slower frequency (see
Section 8.8 “CCLK modification: DIVM register”).
Remark: fosc is defined as the OSCCLK frequency.
CCLK — CPU clock; output of the clock divider. There are two CCLK cycles per machine
cycle, and most instructions are executed in one to two machine cycles (two or four CCLK
cycles).
RCCLK — The internal 7.373 MHz RC oscillator output.
PCLK — Clock for the various peripheral devices and is CCLK 2.
8.3.2 CPU clock (OSCCLK)
The P89LPC933/934/935/936 provides several user-selectable oscillator options in
generating the CPU clock. This allows optimization for a range of needs from high
precision to lowest possible cost. These options are configured when the flash is
programmed and include an on-chip watchdog oscillator, an on-chip RC oscillator, an
oscillator using an external crystal, or an external clock source. The crystal oscillator can
be optimized for low, medium, or high frequency crystals covering a range from 20 kHz to
18 MHz.
8.3.3 Low speed oscillator option
This option supports an external crystal in the range of 20 kHz to 100 kHz. Ceramic
resonators are also supported in this configuration.
8.3.4 Medium speed oscillator option
This option supports an external crystal in the range of 100 kHz to 4 MHz. Ceramic
resonators are also supported in this configuration.
8.3.5 High speed oscillator option
This option supports an external crystal in the range of 4 MHz to 18 MHz. Ceramic
resonators are also supported in this configuration.
8.3.6 Clock output
The P89LPC933/934/935/936 supports a user-selectable clock output function on the
XTAL2/CLKOUT pin when crystal oscillator is not being used. This condition occurs if
another clock source has been selected (on-chip RC oscillator, watchdog oscillator,
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
24 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
external clock input on X1) and if the RTC is not using the crystal oscillator as its clock
source. This allows external devices to synchronize to the P89LPC933/934/935/936. This
output is enabled by the ENCLK bit in the TRIM register.
The frequency of this clock output is 1 2 that of the CCLK. If the clock output is not needed
in Idle mode, it may be turned off prior to entering Idle, saving additional power.
8.4 On-chip RC oscillator option
The P89LPC933/934/935/936 has a 6-bit TRIM register that can be used to tune the
frequency of the RC oscillator. During reset, the TRIM value is initialized to a factory
preprogrammed value to adjust the oscillator frequency to 7.373 MHz 1 % at room
temperature. End-user applications can write to the TRIM register to adjust the on-chip
RC oscillator to other frequencies.
8.5 Watchdog oscillator option
The watchdog has a separate oscillator which has a frequency of 400 kHz. This oscillator
can be used to save power when a high clock frequency is not needed.
8.6 External clock input option
In this configuration, the processor clock is derived from an external source driving the
P3.1/XTAL1 pin. The rate may be from 0 Hz up to 18 MHz. The P3.0/XTAL2 pin may be
used as a standard port pin or a clock output. When using an oscillator frequency
above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit
is required to hold the device in reset at power-up until VDD has reached its
specified level. When system power is removed VDD will fall below the minimum
specified operating voltage. When using an oscillator frequency above 12 MHz, in
some applications, an external brownout detect circuit may be required to hold the
device in reset when VDD falls below the minimum specified operating voltage.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
25 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
Fig 8.
P89LPC933_934_935_936
Product data sheet
Block diagram of oscillator control
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
26 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.7 CCLK wake-up delay
The P89LPC933/934/935/936 has an internal wake-up timer that delays the clock until it
stabilizes depending on the clock source used. If the clock source is any of the three
crystal selections (low, medium and high frequencies) the delay is 992 OSCCLK cycles
plus 60 s to 100 s. If the clock source is either the internal RC oscillator, watchdog
oscillator, or external clock, the delay is 224 OSCCLK cycles plus 60 s to 100 s.
8.8 CCLK modification: DIVM register
The OSCCLK frequency can be divided down up to 510 times by configuring a dividing
register, DIVM, to generate CCLK. This feature makes it possible to temporarily run the
CPU at a lower rate, reducing power consumption. By dividing the clock, the CPU can
retain the ability to respond to events that would not exit Idle mode by executing its normal
program at a lower rate. This can also allow bypassing the oscillator start-up time in cases
where Power-down mode would otherwise be used. The value of DIVM may be changed
by the program at any time without interrupting code execution.
8.9 Low power select
The P89LPC933/934/935/936 is designed to run at 18 MHz (CCLK) maximum. However,
if CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to logic 1 to lower
the power consumption further. On any reset, CLKLP is logic 0 allowing highest
performance access. This bit can then be set in software if CCLK is running at 8 MHz or
slower.
8.10 Memory organization
The various P89LPC933/934/935/936 memory spaces are as follows:
• DATA
128 bytes of internal data memory space (00H:7FH) accessed via direct or indirect
addressing, using instructions other than MOVX and MOVC. All or part of the Stack
may be in this area.
• IDATA
Indirect Data. 256 bytes of internal data memory space (00H:FFH) accessed via
indirect addressing using instructions other than MOVX and MOVC. All or part of the
Stack may be in this area. This area includes the DATA area and the 128 bytes
immediately above it.
• SFR
Selected CPU registers and peripheral control and status registers, accessible only
via direct addressing.
• XDATA (P89LPC935/936)
‘External’ Data or Auxiliary RAM. Duplicates the classic 80C51 64 kB memory space
addressed via the MOVX instruction using the SPTR, R0, or R1. All or part of this
space could be implemented on-chip. The P89LPC935/936 has 512 bytes of on-chip
XDATA memory.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
27 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
• CODE
64 kB of code memory space, accessed as part of program execution and via the
MOVC instruction. The P89LPC933/934/935/936 have 4 KB/8 kB/16 kB of on-chip
Code memory.
The P89LPC935/936 also has 512 bytes of on-chip data EEPROM that is accessed via
SFRs (see Section 8.27 “Data EEPROM (P89LPC935/936)”).
8.11 Data RAM arrangement
The 768 bytes of on-chip RAM are organized as shown in Table 7.
Table 7.
On-chip data memory usages
Type
Data RAM
Size (bytes)
DATA
Memory that can be addressed directly and indirectly
128
IDATA
Memory that can be addressed indirectly
256
XDATA
Auxiliary (‘External Data’) on-chip memory that is accessed
using the MOVX instructions (P89LPC935/936)
512
8.12 Interrupts
The P89LPC933/934/935/936 uses a four priority level interrupt structure. This allows
great flexibility in controlling the handling of the many interrupt sources. The
P89LPC933/934/935/936 supports 15 interrupt sources: external interrupts 0 and 1,
timers 0 and 1, serial port Tx, serial port Rx, combined serial port Rx/Tx, brownout detect,
watchdog/Real-Time clock, I2C-bus, keyboard, comparators 1 and 2, SPI, CCU, data
EEPROM write/ADC completion.
Each interrupt source can be individually enabled or disabled by setting or clearing a bit in
the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a global
disable bit, EA, which disables all interrupts.
Each interrupt source can be individually programmed to one of four priority levels by
setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1, and IP1H. An
interrupt service routine in progress can be interrupted by a higher priority interrupt, but
not by another interrupt of the same or lower priority. The highest priority interrupt service
cannot be interrupted by any other interrupt source. If two requests of different priority
levels are pending at the start of an instruction, the request of higher priority level is
serviced.
If requests of the same priority level are pending at the start of an instruction, an internal
polling sequence determines which request is serviced. This is called the arbitration
ranking.
Remark: The arbitration ranking is only used to resolve pending requests of the same
priority level.
8.12.1 External interrupt inputs
The P89LPC933/934/935/936 has two external interrupt inputs as well as the Keypad
Interrupt function. The two interrupt inputs are identical to those present on the standard
80C51 microcontrollers.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
28 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
These external interrupts can be programmed to be level-triggered or edge-triggered by
setting or clearing bit IT1 or IT0 in register TCON.
In edge-triggered mode, if successive samples of the INTn pin show a HIGH in one cycle
and a LOW in the next cycle, the interrupt request flag IEn in TCON is set, causing an
interrupt request.
If an external interrupt is enabled when the P89LPC933/934/935/936 is put into
Power-down or Idle mode, the interrupt will cause the processor to wake-up and resume
operation. Refer to Section 8.15 “Power reduction modes” for details.
(1) See Section 8.19 “CCU (P89LPC935/936)”
(2) P89LPC935/936
Fig 9.
Interrupt sources, interrupt enables, and power-down wake-up sources
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
29 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.13 I/O ports
The P89LPC933/934/935/936 has four I/O ports: Port 0, Port 1, Port 2, and Port 3.
Ports 0, 1 and 2 are 8-bit ports, and Port 3 is a 2-bit port. The exact number of I/O pins
available depends upon the clock and reset options chosen, as shown in Table 8.
Table 8.
Number of I/O pins available
Clock source
Reset option
Number of I/O pins
(28-pin package)
On-chip oscillator or watchdog
oscillator
No external reset (except during
power-up)
26
External RST pin supported
25
No external reset (except during
power-up)
25
External RST pin supported[1]
24
No external reset (except during
power-up)
24
External RST pin supported[1]
23
External clock input
Low/medium/high speed oscillator
(external crystal or resonator)
[1]
Required for operation above 12 MHz.
8.13.1 Port configurations
All but three I/O port pins on the P89LPC933/934/935/936 may be configured by software
to one of four types on a bit-by-bit basis. These are: quasi-bidirectional (standard 80C51
port outputs), push-pull, open drain, and input-only. Two configuration registers for each
port select the output type for each port pin.
1. P1.5 (RST) can only be an input and cannot be configured.
2. P1.2 (SCL/T0) and P1.3 (SDA/INT0) may only be configured to be either input-only or
open-drain.
8.13.1.1 Quasi-bidirectional output configuration
Quasi-bidirectional output type can be used as both an input and output without the need
to reconfigure the port. This is possible because when the port outputs a logic HIGH, it is
weakly driven, allowing an external device to pull the pin LOW. When the pin is driven
LOW, it is driven strongly and able to sink a fairly large current. These features are
somewhat similar to an open-drain output except that there are three pull-up transistors in
the quasi-bidirectional output that serve different purposes.
The P89LPC933/934/935/936 is a 3 V device, but the pins are 5 V-tolerant. In
quasi-bidirectional mode, if a user applies 5 V on the pin, there will be a current flowing
from the pin to VDD, causing extra power consumption. Therefore, applying 5 V in
quasi-bidirectional mode is discouraged.
A quasi-bidirectional port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
8.13.1.2
Open-drain output configuration
The open-drain output configuration turns off all pull-ups and only drives the pull-down
transistor of the port driver when the port latch contains a logic 0. To be used as a logic
output, a port configured in this manner must have an external pull-up, typically a resistor
tied to VDD.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
30 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
An open-drain port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
8.13.1.3 Input-only configuration
The input-only port configuration has no output drivers. It is a Schmitt trigger input that
also has a glitch suppression circuit.
8.13.1.4
Push-pull output configuration
The push-pull output configuration has the same pull-down structure as both the
open-drain and the quasi-bidirectional output modes, but provides a continuous strong
pull-up when the port latch contains a logic 1. The push-pull mode may be used when
more source current is needed from a port output. A push-pull port pin has a Schmitt
trigger input that also has a glitch suppression circuit.
8.13.2 Port 0 analog functions
The P89LPC933/934/935/936 incorporates two Analog Comparators. In order to give the
best analog function performance and to minimize power consumption, pins that are being
used for analog functions must have the digital outputs and digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input-Only
(high-impedance) mode.
Digital inputs on Port 0 may be disabled through the use of the PT0AD register, bits 1:5.
On any reset, PT0AD[1:5] defaults to logic 0s to enable digital functions.
8.13.3 Additional port features
After power-up, all pins are in Input-Only mode.
Remark: Please note that this is different from the LPC76x series of devices.
• After power-up, all I/O pins except P1.5, may be configured by software.
• Pin P1.5 is input only. Pins P1.2 and P1.3 and are configurable for either input-only or
open-drain.
Every output on the P89LPC933/934/935/936 has been designed to sink typical LED
drive current. However, there is a maximum total output current for all ports which must
not be exceeded. Please refer to Table 11 “Static characteristics” for detailed
specifications.
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
8.14 Power monitoring functions
The P89LPC933/934/935/936 incorporates power monitoring functions designed to
prevent incorrect operation during initial power-up and power loss or reduction during
operation. This is accomplished with two hardware functions: Power-on detect and
brownout detect.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
31 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.14.1 Brownout detection
The brownout detect function determines if the power supply voltage drops below a
certain level. The default operation is for a brownout detection to cause a processor reset,
however it may alternatively be configured to generate an interrupt.
Brownout detection may be enabled or disabled in software.
If brownout detection is enabled the brownout condition occurs when V DD falls below the
brownout trip voltage, Vbo (see Table 11 “Static characteristics”), and is negated when VDD
rises above Vbo. If the P89LPC933/934/935/936 device is to operate with a power supply
that can be below 2.7 V, BOE should be left in the unprogrammed state so that the device
can operate at 2.4 V, otherwise continuous brownout reset may prevent the device from
operating.
For correct activation of brownout detect, the VDD rise and fall times must be observed.
Please see Table 11 “Static characteristics” for specifications.
8.14.2 Power-on detection
The power-on detect has a function similar to the brownout detect, but is designed to work
as power comes up initially, before the power supply voltage reaches a level where
brownout detect can work. The POF flag in the RSTSRC register is set to indicate an
initial power-up condition. The POF flag will remain set until cleared by software.
8.15 Power reduction modes
The P89LPC933/934/935/936 supports three different power reduction modes. These
modes are Idle mode, Power-down mode, and total Power-down mode.
8.15.1 Idle mode
Idle mode leaves peripherals running in order to allow them to activate the processor
when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle
mode.
8.15.2 Power-down mode
The Power-down mode stops the oscillator in order to minimize power consumption. The
P89LPC933/934/935/936 exits Power-down mode via any reset, or certain interrupts. In
Power-down mode, the power supply voltage may be reduced to the RAM keep-alive
voltage VRAM. This retains the RAM contents at the point where Power-down mode was
entered. SFR contents are not guaranteed after VDD has been lowered to VDDR, therefore
it is highly recommended to wake-up the processor via reset in this case. V DD must be
raised to within the operating range before the Power-down mode is exited.
Some chip functions continue to operate and draw power during Power-down mode,
increasing the total power used during power-down. These include: brownout detect,
watchdog timer, Comparators (note that Comparators can be powered-down separately),
and RTC/system timer. The internal RC oscillator is disabled unless both the RC oscillator
has been selected as the system clock and the RTC is enabled.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
32 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.15.3 Total Power-down mode
This is the same as Power-down mode except that the brownout detection circuitry and
the voltage comparators are also disabled to conserve additional power. The internal RC
oscillator is disabled unless both the RC oscillator has been selected as the system clock
and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during
power-down, there will be high power consumption. Please use an external low frequency
clock to achieve low power with the RTC running during power-down.
8.16 Reset
The P1.5/RST pin can function as either a LOW-active reset input or as a digital input,
P1.5. The Reset Pin Enable (RPE) bit in UCFG1, when set to logic 1, enables the external
reset input function on P1.5. When cleared, P1.5 may be used as an input pin.
Remark: During a power-up sequence, the RPE selection is overridden and this pin will
always functions as a reset input. An external circuit connected to this pin should not
hold this pin LOW during a power-on sequence as this will keep the device in reset.
After power-up this input will function either as an external reset input or as a digital input
as defined by the RPE bit. Only a power-up reset will temporarily override the selection
defined by RPE bit. Other sources of reset will not override the RPE bit. When this pin
functions as a reset input, an internal pull-up resistance is connected (see Table 11 “Static
characteristics”).
Reset can be triggered from the following sources:
•
•
•
•
•
•
External reset pin (during power-up or if user configured via UCFG1).
Power-on detect.
Brownout detect.
Watchdog timer.
Software reset.
UART break character detect reset.
For every reset source, there is a flag in the reset register, RSTSRC. The user can read
this register to determine the most recent reset source. These flag bits can be cleared in
software by writing a logic 0 to the corresponding bit. More than one flag bit may be set:
• During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
• For any other reset, previously set flag bits that have not been cleared will remain set.
8.16.1 Reset vector
Following reset, the P89LPC933/934/935/936 will fetch instructions from either address
0000H or the boot address. The boot address is formed by using the boot vector as the
high byte of the address and the low byte of the address = 00H.
The boot address will be used if a UART break reset occurs, or the non-volatile boot
status bit (BOOTSTAT.0) = 1, or the device is forced into ISP mode during power-on (see
P89LPC933/934/935/936
). Otherwise, instructions will be fetched from
address 0000H.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
33 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.17 Timers/counters 0 and 1
The P89LPC933/934/935/936 has two general purpose counter/timers which are upward
compatible with the standard 80C51 Timer 0 and Timer 1. Both can be configured to
operate either as timers or event counter. An option to automatically toggle the T0 and/or
T1 pins upon timer overflow has been added.
In the ‘timer’ function, the register is incremented every machine cycle.
In the ‘counter’ function, the register is incremented in response to a 1-to-0 transition at its
corresponding external input pin, T0 or T1. In this function, the external input is sampled
once during every machine cycle.
Timer 0 and Timer 1 have five operating modes (modes 0, 1, 2, 3 and 6). Modes 0, 1, 2
and 6 are the same for both timers/counters. Mode 3 is different.
8.17.1 Mode 0
Putting either timer into Mode 0 makes it look like an 8048 timer, which is an 8-bit counter
with a divide-by-32 prescaler. In this mode, the timer register is configured as a 13-bit
register. Mode 0 operation is the same for Timer 0 and Timer 1.
8.17.2 Mode 1
Mode 1 is the same as Mode 0, except that all 16 bits of the timer register are used.
8.17.3 Mode 2
Mode 2 configures the timer register as an 8-bit counter with automatic reload. Mode 2
operation is the same for Timer 0 and Timer 1.
8.17.4 Mode 3
When Timer 1 is in Mode 3 it is stopped. Timer 0 in Mode 3 forms two separate 8-bit
counters and is provided for applications that require an extra 8-bit timer. When Timer 1 is
in Mode 3 it can still be used by the serial port as a baud rate generator.
8.17.5 Mode 6
In this mode, the corresponding timer can be changed to a PWM with a full period of
256 timer clocks.
8.17.6 Timer overflow toggle output
Timers 0 and 1 can be configured to automatically toggle a port output whenever a timer
overflow occurs. The same device pins that are used for the T0 and T1 count inputs are
also used for the timer toggle outputs. The port outputs will be a logic 1 prior to the first
timer overflow when this mode is turned on.
8.18 RTC/system timer
The P89LPC933/934/935/936 has a simple RTC that allows a user to continue running an
accurate timer while the rest of the device is powered-down. The RTC can be a wake-up
or an interrupt source. The RTC is a 23-bit down counter comprised of a 7-bit prescaler
and a 16-bit loadable down counter. When it reaches all logic 0s, the counter will be
reloaded again and the RTCF flag will be set. The clock source for this counter can be
either the CPU clock (CCLK) or the XTAL oscillator, provided that the XTAL oscillator is
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
34 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
not being used as the CPU clock. If the XTAL oscillator is used as the CPU clock, then the
RTC will use CCLK as its clock source. Only power-on reset will reset the RTC and its
associated SFRs to the default state.
8.19 CCU (P89LPC935/936)
This unit features:
• A 16-bit timer with 16-bit reload on overflow.
• Selectable clock, with prescaler to divide clock source by any integral number
between 1 and 1024.
•
•
•
•
Four compare/PWM outputs with selectable polarity.
Symmetrical/asymmetrical PWM selection.
Two capture inputs with event counter and digital noise rejection filter.
Seven interrupts with common interrupt vector (one overflow, two capture,
four compare).
• Safe 16-bit read/write via shadow registers.
8.19.1 CCU clock
The CCU runs on the CCUCLK, which is either PCLK in basic timer mode, or the output of
a Phase-Locked Loop (PLL). The PLL is designed to use a clock source between 0.5 MHz
to 1 MHz that is multiplied by 32 to produce a CCUCLK between 16 MHz and 32 MHz in
PWM mode (asymmetrical or symmetrical). The PLL contains a 4-bit divider to help divide
PCLK into a frequency between 0.5 MHz and 1 MHz.
8.19.2 CCUCLK prescaling
This CCUCLK can further be divided down by a prescaler. The prescaler is implemented
as a 10-bit free-running counter with programmable reload at overflow.
8.19.3 Basic timer operation
The timer is a free-running up/down counter with a direction control bit. If the timer
counting direction is changed while the counter is running, the count sequence will be
reversed. The timer can be written or read at any time.
When a reload occurs, the CCU Timer Overflow Interrupt Flag will be set, and an interrupt
generated if enabled. The 16-bit CCU timer may also be used as an 8-bit up/down timer.
8.19.4 Output compare
There are four output compare channels A, B, C and D. Each output compare channel
needs to be enabled in order to operate and the user will have to set the associated I/O
pin to the desired output mode to connect the pin. When the contents of the timer matches
that of a capture compare control register, the Timer Output Compare Interrupt Flag
(TOCFx) becomes set. An interrupt will occur if enabled.
8.19.5 Input capture
Input capture is always enabled. Each time a capture event occurs on one of the two input
capture pins, the contents of the timer is transferred to the corresponding 16-bit input
capture register. The capture event can be programmed to be either rising or falling edge
triggered. A simple noise filter can be enabled on the input capture by enabling the Input
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
35 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Capture Noise Filter bit. If set, the capture logic needs to see four consecutive samples of
the same value in order to recognize an edge as a capture event. An event counter can be
set to delay a capture by a number of capture events.
8.19.6 PWM operation
PWM operation has two main modes, symmetrical and asymmetrical.
In asymmetrical PWM operation the CCU timer operates in down-counting mode
regardless of the direction control bit.
In symmetrical mode, the timer counts up/down alternately. The main difference from
basic timer operation is the operation of the compare module, which in PWM mode is
used for PWM waveform generation.
As with basic timer operation, when the PWM (compare) pins are connected to the
compare logic, their logic state remains unchanged. However, since bit FCO is used to
hold the halt value, only a compare event can change the state of the pin.
Fig 10. Asymmetrical PWM, down-counting mode
Fig 11. Symmetrical PWM
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
36 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.19.7 Alternating output mode
In asymmetrical mode, the user can set up PWM channels A/B and C/D as alternating
pairs for bridge drive control. In this mode the output of these PWM channels are
alternately gated on every counter cycle.
Fig 12. Alternate output mode
8.19.8 PLL operation
The PWM module features a PLL that can be used to generate a CCUCLK frequency
between 16 MHz and 32 MHz. At this frequency the PWM module provides ultrasonic
PWM frequency with 10-bit resolution provided that the crystal frequency is 1 MHz or
higher. The PLL is fed an input signal from 0.5 MHz to 1 MHz and generates an output
signal of 32 times the input frequency. This signal is used to clock the timer. The user will
have to set a divider that scales PCLK by a factor from 1 to 16. This divider is found in the
SFR register TCR21. The PLL frequency can be expressed as shown in Equation 1.
PCLK
PLL frequency = -----------------N+1
Where: N is the value of PLLDV.3 to PLLDV.0.
(1)
Since N ranges from 0 to 15, the CCLK frequency can be in the range of PCLK to
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
PCLK
16.
© NXP B.V. 2011. All rights reserved.
37 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.19.9 CCU interrupts
There are seven interrupt sources on the CCU which share a common interrupt vector.
Fig 13. Capture/compare unit interrupts
8.20 UART
The P89LPC933/934/935/936 has an enhanced UART that is compatible with the
conventional 80C51 UART except that Timer 2 overflow cannot be used as a baud rate
source. The P89LPC933/934/935/936 does include an independent baud rate generator.
The baud rate can be selected from the oscillator (divided by a constant), Timer 1
overflow, or the independent baud rate generator. In addition to the baud rate generation,
enhancements over the standard 80C51 UART include Framing Error detection,
automatic address recognition, selectable double buffering and several interrupt options.
The UART can be operated in four modes: shift register, 8-bit UART, 9-bit UART, and CPU
clock
clock .
32 or CPU
16
8.20.1 Mode 0
Serial data enters and exits through RXD. TXD outputs the shift clock. 8 bits are
transmitted or received, LSB first. The baud rate is fixed at 1 16 of the CPU clock
frequency.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
38 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.20.2 Mode 1
10 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0),
8 data bits (LSB first), and a stop bit (logic 1). When data is received, the stop bit is stored
in RB8 in special function register SCON. The baud rate is variable and is determined by
the Timer 1 overflow rate or the baud rate generator (described in Section 8.20.5 “Baud
rate generator and selection”).
8.20.3 Mode 2
11 bits are transmitted (through TXD) or received (through RXD): start bit (logic 0), 8 data
bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). When data is
transmitted, the 9th data bit (TB8 in SCON) can be assigned the value of logic 0 or logic 1.
Or, for example, the parity bit (P, in the PSW) could be moved into TB8. When data is
received, the 9th data bit goes into RB8 in special function register SCON, while the stop
bit is not saved. The baud rate is programmable to either 1 16 or 1 32 of the CPU clock
frequency, as determined by the SMOD1 bit in PCON.
8.20.4 Mode 3
11 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0), 8
data bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). In fact, Mode 3 is
the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable
and is determined by the Timer 1 overflow rate or the baud rate generator (described in
Section 8.20.5 “Baud rate generator and selection”).
8.20.5 Baud rate generator and selection
The P89LPC933/934/935/936 enhanced UART has an independent baud rate generator.
The baud rate is determined by a baud-rate preprogrammed into the BRGR1 and BRGR0
SFRs which together form a 16-bit baud rate divisor value that works in a similar manner
as Timer 1 but is much more accurate. If the baud rate generator is used, Timer 1 can be
used for other timing functions.
The UART can use either Timer 1 or the baud rate generator output (see Figure 14). Note
that Timer T1 is further divided by 2 if the SMOD1 bit (PCON.7) is cleared. The
independent baud rate generator uses CCLK.
Fig 14. Baud rate sources for UART (Modes 1, 3)
8.20.6 Framing error
Framing error is reported in the status register (SSTAT). In addition, if SMOD0 (PCON.6)
is logic 1, framing errors can be made available in SCON.7 respectively. If SMOD0 is
logic 0, SCON.7 is SM0. It is recommended that SM0 and SM1 (SCON.7:6) are set up
when SMOD0 is logic 0.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
39 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.20.7 Break detect
Break detect is reported in the status register (SSTAT). A break is detected when
11 consecutive bits are sensed LOW. The break detect can be used to reset the device
and force the device into ISP mode.
8.20.8 Double buffering
The UART has a transmit double buffer that allows buffering of the next character to be
written to SBUF while the first character is being transmitted. Double buffering allows
transmission of a string of characters with only one stop bit between any two characters,
as long as the next character is written between the start bit and the stop bit of the
previous character.
Double buffering can be disabled. If disabled (DBMOD, i.e., SSTAT.7 = 0), the UART is
compatible with the conventional 80C51 UART. If enabled, the UART allows writing to
SnBUF while the previous data is being shifted out. Double buffering is only allowed in
Modes 1, 2 and 3. When operated in Mode 0, double buffering must be disabled
(DBMOD = 0).
8.20.9 Transmit interrupts with double buffering enabled (modes 1, 2 and 3)
Unlike the conventional UART, in double buffering mode, the Tx interrupt is generated
when the double buffer is ready to receive new data.
8.20.10 The 9th bit (bit 8) in double buffering (modes 1, 2 and 3)
If double buffering is disabled TB8 can be written before or after SBUF is written, as long
as TB8 is updated some time before that bit is shifted out. TB8 must not be changed until
the bit is shifted out, as indicated by the Tx interrupt.
If double buffering is enabled, TB8 must be updated before SBUF is written, as TB8 will
be double-buffered together with SBUF data.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
40 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.21 I2C-bus serial interface
The I2C-bus uses two wires (SDA and SCL) to transfer information between devices
connected to the bus, and it has the following features:
• Bidirectional data transfer between masters and slaves
• Multi master bus (no central master)
• Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer
• The I2C-bus may be used for test and diagnostic purposes.
A typical I2C-bus configuration is shown in Figure 15. The P89LPC933/934/935/936
device provides a byte-oriented I2C-bus interface that supports data transfers up to
400 kHz.
P89LPC935
Fig 15. I2C-bus configuration
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
41 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
Fig 16. I2C-bus serial interface block diagram
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
42 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
8.22 SPI
The P89LPC933/934/935/936 provides another high-speed serial communication
interface—the SPI interface. SPI is a full-duplex, high-speed, synchronous
communication bus with two operation modes: Master mode and Slave mode. Up to
3 Mbit/s can be supported in Master mode or up to 2 Mbit/s in Slave mode. It has a
Transfer Completion Flag and Write Collision Flag Protection.
Fig 17. SPI block diagram
The SPI interface has four pins: SPICLK, MOSI, MISO and SS:
• SPICLK, MOSI and MISO are typically tied together between two or more SPI
devices. Data flows from master to slave on MOSI (Master Out Slave In) pin and flows
from slave to master on MISO (Master In Slave Out) pin. The SPICLK signal is output
in the master mode and is input in the slave mode. If the SPI system is disabled, i.e.,
SPEN (SPCTL.6) = 0 (reset value), these pins are configured for port functions.
• SS is the optional slave select pin. In a typical configuration, an SPI master asserts
one of its port pins to select one SPI device as the current slave. An SPI slave device
uses its SS pin to determine whether it is selected.
Typical connections are shown in Figure 18 through Figure 20.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
43 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.22.1 Typical SPI configurations
Fig 18. SPI single master single slave configuration
Fig 19. SPI dual device configuration, where either can be a master or a slave
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
44 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
Fig 20. SPI single master multiple slaves configuration
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
45 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.23 Analog comparators
Two analog comparators are provided on the P89LPC933/934/935/936. Input and output
options allow use of the comparators in a number of different configurations. Comparator
operation is such that the output is a logic 1 (which may be read in a register and/or routed
to a pin) when the positive input (one of two selectable pins) is greater than the negative
input (selectable from a pin or an internal reference voltage). Otherwise the output is a
zero. Each comparator may be configured to cause an interrupt when the output value
changes.
The overall connections to both comparators are shown in Figure 21. The comparators
function to VDD = 2.4 V.
When each comparator is first enabled, the comparator output and interrupt flag are not
guaranteed to be stable for 10 microseconds. The corresponding comparator interrupt
should not be enabled during that time, and the comparator interrupt flag must be cleared
before the interrupt is enabled in order to prevent an immediate interrupt service.
When a comparator is disabled the comparator’s output, COn, goes HIGH. If the
comparator output was LOW and then is disabled, the resulting transition of the
comparator output from a LOW to HIGH state will set the comparator flag, CMFn. This will
cause an interrupt if the comparator interrupt is enabled. The user should therefore
disable the comparator interrupt prior to disabling the comparator. Additionally, the user
should clear the comparator flag, CMFn, after disabling the comparator.
Fig 21. Comparator input and output connections
8.23.1 Internal reference voltage
An internal reference voltage generator may supply a default reference when a single
comparator input pin is used. The value of the internal reference voltage, referred to as
Vref(bg), is 1.23 V 10 %.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
46 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.23.2 Comparator interrupt
Each comparator has an interrupt flag contained in its configuration register. This flag is
set whenever the comparator output changes state. The flag may be polled by software or
may be used to generate an interrupt. The two comparators use one common interrupt
vector. If both comparators enable interrupts, after entering the interrupt service routine,
the user needs to read the flags to determine which comparator caused the interrupt.
8.23.3 Comparators and power reduction modes
Either or both comparators may remain enabled when Power-down or Idle mode is
activated, but both comparators are disabled automatically in Total Power-down mode.
If a comparator interrupt is enabled (except in Total Power-down mode), a change of the
comparator output state will generate an interrupt and wake-up the processor. If the
comparator output to a pin is enabled, the pin should be configured in the push-pull mode
in order to obtain fast switching times while in Power-down mode. The reason is that with
the oscillator stopped, the temporary strong pull-up that normally occurs during switching
on a quasi-bidirectional port pin does not take place.
Comparators consume power in Power-down and Idle modes, as well as in the normal
operating mode. This fact should be taken into account when system power consumption
is an issue. To minimize power consumption, the user can disable the comparators via
PCONA.5, or put the device in Total Power-down mode.
8.24 Keypad interrupt
The Keypad Interrupt (KBI) function is intended primarily to allow a single interrupt to be
generated when Port 0 is equal to or not equal to a certain pattern. This function can be
used for bus address recognition or keypad recognition. The user can configure the port
via SFRs for different tasks.
The Keypad Interrupt Mask register (KBMASK) is used to define which input pins
connected to Port 0 can trigger the interrupt. The Keypad Pattern register (KBPATN) is
used to define a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag
(KBIF) in the Keypad Interrupt Control register (KBCON) is set when the condition is
matched while the Keypad Interrupt function is active. An interrupt will be generated if
enabled. The PATN_SEL bit in the Keypad Interrupt Control register (KBCON) is used to
define equal or not-equal for the comparison.
In order to use the Keypad Interrupt as an original KBI function like in 87LPC76x series,
the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then any key
connected to Port 0 which is enabled by the KBMASK register will cause the hardware to
set KBIF and generate an interrupt if it has been enabled. The interrupt may be used to
wake-up the CPU from Idle or Power-down modes. This feature is particularly useful in
handheld, battery-powered systems that need to carefully manage power consumption
yet also need to be convenient to use.
In order to set the flag and cause an interrupt, the pattern on Port 0 must be held longer
than six CCLKs.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
47 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.25 Watchdog timer
The watchdog timer causes a system reset when it underflows as a result of a failure to
feed the timer prior to the timer reaching its terminal count. It consists of a programmable
12-bit prescaler, and an 8-bit down counter. The down counter is decremented by a tap
taken from the prescaler. The clock source for the prescaler is either the PCLK or the
nominal 400 kHz watchdog oscillator. The watchdog timer can only be reset by a
power-on reset. When the watchdog feature is disabled, it can be used as an interval
timer and may generate an interrupt. Figure 22 shows the watchdog timer in Watchdog
mode. Feeding the watchdog requires a two-byte sequence. If PCLK is selected as the
watchdog clock and the CPU is powered-down, the watchdog is disabled. The watchdog
timer has a time-out period that ranges from a few s to a few seconds. Please refer to the
P89LPC933/934/935/936
for more details.
(1) Watchdog reset can also be caused by an invalid feed sequence, or by writing to WDCON not immediately followed by a feed
sequence.
Fig 22. Watchdog timer in Watchdog mode (WDTE = 1)
8.26 Additional features
8.26.1 Software reset
The SRST bit in AUXR1 gives software the opportunity to reset the processor completely,
as if an external reset or watchdog reset had occurred. Care should be taken when writing
to AUXR1 to avoid accidental software resets.
8.26.2 Dual data pointers
The dual Data Pointers (DPTR) provides two different Data Pointers to specify the
address used with certain instructions. The DPS bit in the AUXR1 register selects one of
the two Data Pointers. Bit 2 of AUXR1 is permanently wired as a logic 0 so that the DPS
bit may be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1
register, without the possibility of inadvertently altering other bits in the register.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
48 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.27 Data EEPROM (P89LPC935/936)
The P89LPC935/936 has 512 bytes of on-chip Data EEPROM. The Data EEPROM is
SFR based, byte readable, byte writable, and erasable (via row fill and sector fill). The
user can read, write and fill the memory via SFRs and one interrupt. This Data EEPROM
provides 100,000 minimum erase/program cycles for each byte.
• Byte mode: In this mode, data can be read and written one byte at a time.
• Row fill: In this mode, the addressed row (64 bytes) is filled with a single value. The
entire row can be erased by writing 00H.
• Sector fill: In this mode, all 512 bytes are filled with a single value. The entire sector
can be erased by writing 00H.
After the operation finishes, the hardware will set the EEIF bit, which if enabled will
generate an interrupt. The flag is cleared by software.
8.28 Flash program memory
8.28.1 General description
The P89LPC933/934/935/936 flash memory provides in-circuit electrical erasure and
programming. The flash can be erased, read, and written as bytes. The Sector and Page
Erase functions can erase any flash sector (1 kB or 2 kB depending on the device) or
page (64 bytes). The Chip Erase operation will erase the entire program memory. ICP
using standard commercial programmers is available. In addition, IAP and byte-erase
allows code memory to be used for non-volatile data storage. On-chip erase and write
timing generation contribute to a user-friendly programming interface. The
P89LPC933/934/935/936 flash reliably stores memory contents even after 100,000 erase
and program cycles. The cell is designed to optimize the erase and programming
mechanisms. The P89LPC933/934/935/936 uses VDD as the supply voltage to perform
the Program/Erase algorithms.
8.28.2 Features
•
•
•
•
•
Programming and erase over the full operating voltage range.
Byte erase allows code memory to be used for data storage.
Read/Programming/Erase using ISP/IAP/ICP.
Internal fixed boot ROM, containing low-level IAP routines available to user code.
Default loader providing ISP via the serial port, located in upper end of user program
memory.
• Boot vector allows user-provided flash loader code to reside anywhere in the flash
memory space, providing flexibility to the user.
•
•
•
•
•
P89LPC933_934_935_936
Product data sheet
Any flash program/erase operation in 2 ms.
Programming with industry-standard commercial programmers.
Programmable security for the code in the flash for each sector.
100,000 typical erase/program cycles for each byte.
10 year minimum data retention.
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
49 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.28.3 Flash organization
The program memory consists of eight 2 kB sectors on the P89LPC936 device, eight 1 kB
sectors on the P89LPC934/935 devices, and four 1 kB sectors on the P89LPC933 device.
Each sector can be further divided into 64-byte pages. In addition to sector erase, page
erase, and byte erase, a 64-byte page register is included which allows from 1 to 64 bytes
of a given page to be programmed at the same time, substantially reducing overall
programming time.
8.28.4 Using flash as data storage
The flash code memory array of this device supports individual byte erasing and
programming. Any byte in the code memory array may be read using the MOVC
instruction, provided that the sector containing the byte has not been secured (a MOVC
instruction is not allowed to read code memory contents of a secured sector). Thus any
byte in a non-secured sector may be used for non-volatile data storage.
8.28.5 Flash programming and erasing
Four different methods of erasing or programming of the flash are available. The flash
may be programmed or erased in the end-user application (IAP) under control of the
application’s firmware. Another option is to use the ICP mechanism. This ICP system
provides for programming through a serial clock - serial data interface. As shipped from
the factory, the upper 512 bytes of user code space contains a serial ISP routine allowing
the device to be programmed in circuit through the serial port. The flash may also be
programmed or erased using a commercially available EPROM programmer which
supports this device. This device does not provide for direct verification of code memory
contents. Instead, this device provides a 32-bit CRC result on either a sector or the entire
user code space.
8.28.6 In-circuit programming
ICP is performed without removing the microcontroller from the system. The ICP facility
consists of internal hardware resources to facilitate remote programming of the
P89LPC933/934/935/936 through a two-wire serial interface. The Philips ICP facility has
made ICP in an embedded application—using commercially available
programmers—possible with a minimum of additional expense in components and circuit
board area. The ICP function uses five pins. Only a small connector needs to be available
to interface your application to a commercial programmer in order to use this feature.
Additional details may be found in the P89LPC933/934/935/936
.
8.28.7 In-application programming
IAP is performed in the application under the control of the microcontroller’s firmware. The
IAP facility consists of internal hardware resources to facilitate programming and erasing.
The Philips IAP has made IAP in an embedded application possible without additional
components. Two methods are available to accomplish IAP. A set of predefined IAP
functions are provided in a boot ROM and can be called through a common interface,
PGM_MTP. Several IAP calls are available for use by an application program to permit
selective erasing and programming of flash sectors, pages, security bits, configuration
bytes, and device ID. These functions are selected by setting up the microcontroller’s
registers before making a call to PGM_MTP at FF03H. The boot ROM occupies the
program memory space at the top of the address space from FF00H to FFEFH, thereby
not conflicting with the user program memory space.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
50 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
In addition, IAP operations can be accomplished through the use of four SFRs consisting
of a control/status register, a data register, and two address registers. Additional details
may be found in the P89LPC933/934/935/936
.
8.28.8 ISP
ISP is performed without removing the microcontroller from the system. The ISP facility
consists of a series of internal hardware resources coupled with internal firmware to
facilitate remote programming of the P89LPC933/934/935/936 through the serial port.
This firmware is provided by Philips and embedded within each P89LPC933/934/935/936
device. The Philips ISP facility has made ISP in an embedded application possible with a
minimum of additional expense in components and circuit board area. The ISP function
uses five pins (VDD, VSS, TXD, RXD, and RST). Only a small connector needs to be
available to interface your application to an external circuit in order to use this feature.
8.28.9 Power-on reset code execution
The P89LPC933/934/935/936 contains two special flash elements: the boot vector and
the boot status bit. Following reset, the P89LPC933/934/935/936 examines the contents
of the boot status bit. If the boot status bit is set to zero, power-up execution starts at
location 0000H, which is the normal start address of the user’s application code. When
the boot status bit is set to a value other than zero, the contents of the boot vector are
used as the high byte of the execution address and the low byte is set to 00H.
Table 9 shows the factory default boot vector settings for these devices.
Remark: These settings are different than the original P89LPC932. Tools designed to
support the P89LPC933/934/935/936 should be used to program this device, such as
Flash Magic version 1.98, or later.
A factory-provided boot loader is preprogrammed into the address space indicated and
uses the indicated boot loader entry point to perform ISP functions. This code can be
erased by the user.
Remark: Users who wish to use this loader should take precautions to avoid erasing the
sector that contains this boot loader. Instead, the page erase function can be used to
erase the pages located in this sector which are not used by the boot loader.
A custom boot loader can be written with the boot vector set to the custom boot loader, if
desired.
Table 9.
P89LPC933_934_935_936
Product data sheet
Default boot vector values and ISP entry points
Device
Default
boot vector
Default
boot loader
entry point
Default boot loader Boot sector
code range
range
P89LPC933
0FH
0F00H
0E00H to 0FFFH
0C00H to 0FFFH
P89LPC934
1FH
1F00H
1E00H to 1FFFH
1C00H to 1FFFH
P89LPC935
1FH
1F00H
1E00H to 1FFFH
1C00H to 1FFFH
P89LPC936
3FH
3F00H
3E00H to 3FFFH
3C00H to 3FFFH
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
51 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.28.10 Hardware activation of the boot loader
The boot loader can also be executed by forcing the device into ISP mode during a
power-on sequence (see the P89LPC933/934/935/936
for specific
information). This has the same effect as having a non-zero status byte. This allows an
application to be built that will normally execute user code but can be manually forced into
ISP operation. If the factory default setting for the boot vector is changed, it will no longer
point to the factory preprogrammed ISP boot loader code. After programming the flash,
the status byte should be programmed to zero in order to allow execution of the user’s
application code beginning at address 0000H.
8.29 User configuration bytes
Some user-configurable features of the P89LPC933/934/935/936 must be defined at
power-up and therefore cannot be set by the program after start of execution. These
features are configured through the use of the flash byte UCFG1. Please see the
P89LPC933/934/935/936
for additional details.
8.30 User sector security bytes
There are eight User Sector Security Bytes on the P89LPC933/934/935/936 device. Each
byte corresponds to one sector. Please see the P89LPC933/934/935/936
for
additional details.
9. A/D converter
9.1 General description
The P89LPC935/936 have two 8-bit, 4-channel multiplexed successive approximation
analog-to-digital converter modules sharing common control logic. The P89LPC933/934
have a single 8-bit, 4-channel multiplexed analog-to-digital converter and an additional
DAC module. A block diagram of the A/D converter is shown in Figure 23. Each A/D
consists of a 4-input multiplexer which feeds a sample-and-hold circuit providing an input
signal to one of two comparator inputs. The control logic in combination with the SAR
drives a digital-to-analog converter which provides the other input to the comparator. The
output of the comparator is fed to the SAR.
9.2 Features and benefits
Two (P89LPC935/936) 8-bit, 4-channel multiplexed input, successive approximation
A/D converters with common control logic (one A/D on the P89LPC933/934).
Four result registers for each A/D.
Six operating modes:
Fixed channel, single conversion mode.
Fixed channel, continuous conversion mode.
Auto scan, single conversion mode.
Auto scan, continuous conversion mode.
Dual channel, continuous conversion mode.
Single step mode.
Four conversion start modes:
Timer triggered start.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
52 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Start immediately.
Edge triggered.
Dual start immediately (P89LPC935/936).
8-bit conversion time of 3.9 s at an A/D clock of 3.3 MHz.
Interrupt or polled operation.
Boundary limits interrupt.
DAC output to a port pin with high output impedance.
Clock divider.
Power-down mode.
9.3 Block diagram
Fig 23. ADC block diagram
9.4 A/D operating modes
9.4.1 Fixed channel, single conversion mode
A single input channel can be selected for conversion. A single conversion will be
performed and the result placed in the result register which corresponds to the selected
input channel. An interrupt, if enabled, will be generated after the conversion completes.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
53 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
9.4.2 Fixed channel, continuous conversion mode
A single input channel can be selected for continuous conversion. The results of the
conversions will be sequentially placed in the four result registers. An interrupt, if enabled,
will be generated after every four conversions. Additional conversion results will again
cycle through the four result registers, overwriting the previous results. Continuous
conversions continue until terminated by the user.
9.4.3 Auto scan, single conversion mode
Any combination of the four input channels can be selected for conversion. A single
conversion of each selected input will be performed and the result placed in the result
register which corresponds to the selected input channel. An interrupt, if enabled, will be
generated after all selected channels have been converted. If only a single channel is
selected this is equivalent to single channel, single conversion mode.
9.4.4 Auto scan, continuous conversion mode
Any combination of the four input channels can be selected for conversion. A conversion
of each selected input will be performed and the result placed in the result register which
corresponds to the selected input channel. An interrupt, if enabled, will be generated after
all selected channels have been converted. The process will repeat starting with the first
selected channel. Additional conversion results will again cycle through the four result
registers, overwriting the previous results. Continuous conversions continue until
terminated by the user.
9.4.5 Dual channel, continuous conversion mode
This is a variation of the auto scan continuous conversion mode where conversion occurs
on two user-selectable inputs. The result of the conversion of the first channel is placed in
result register, ADxDAT0. The result of the conversion of the second channel is placed in
result register, ADxDAT1. The first channel is again converted and its result stored in
ADxDAT2. The second channel is again converted and its result placed in ADxDAT3. An
interrupt is generated, if enabled, after every set of four conversions (two conversions per
channel).
9.4.6 Single step mode
This special mode allows ‘single-stepping’ in an auto scan conversion mode. Any
combination of the four input channels can be selected for conversion. After each channel
is converted, an interrupt is generated, if enabled, and the A/D waits for the next start
condition. May be used with any of the start modes.
9.5 Conversion start modes
9.5.1 Timer triggered start
An A/D conversion is started by the overflow of Timer 0. Once a conversion has started,
additional Timer 0 triggers are ignored until the conversion has completed. The Timer
triggered start mode is available in all A/D operating modes.
9.5.2 Start immediately
Programming this mode immediately starts a conversion. This start mode is available in all
A/D operating modes.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
54 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
9.5.3 Edge triggered
An A/D conversion is started by rising or falling edge of P1.4. Once a conversion has
started, additional edge triggers are ignored until the conversion has completed. The edge
triggered start mode is available in all A/D operating modes.
9.5.4 Dual start immediately (P89LPC935/936)
Programming this mode starts a synchronized conversion of both A/D converters. This
start mode is available in all A/D operating modes. Both A/D converters must be in the
same operating mode. In the continuous conversion modes, both A/D converters must
select an identical number of channels. Any trigger of either A/D will start a simultaneous
conversion of both A/Ds.
9.6 Boundary limits interrupt
Each of the A/D converters has both a high and low boundary limit register. After the four
MSBs have been converted, these four bits are compared with the four MSBs of the
boundary high and low registers. If the four MSBs of the conversion are outside the limit
an interrupt will be generated, if enabled. If the conversion result is within the limits, the
boundary limits will again be compared after all 8 bits have been converted. An interrupt
will be generated, if enabled, if the result is outside the boundary limits. The boundary limit
may be disabled by clearing the boundary limit interrupt enable.
9.7 DAC output to a port pin with high output impedance
Each A/D converter’s DAC block can be output to a port pin. In this mode, the ADxDAT3
register is used to hold the value fed to the DAC. After a value has been written to the
DAC (written to ADxDAT3), the DAC output will appear on the channel 3 pin.
9.8 Clock divider
The A/D converter requires that its internal clock source be in the range of 500 kHz to
3.3 MHz to maintain accuracy. A programmable clock divider that divides the clock
from 1 to 8 is provided for this purpose.
9.9 Power-down and Idle mode
In Idle mode the A/C converter, if enabled, will continue to function and can cause the
device to exit Idle mode when the conversion is completed if the A/D interrupt is enabled.
In Power-down mode or Total Power-down mode, the A/D does not function. If the A/D is
enabled, it will consume power. Power can be reduced by disabling the A/D.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
55 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
10. Limiting values
Table 10.
Limiting values
Symbol
Parameter
Tamb(bias)
Tstg
IOH(I/O)
HIGH-level output current per
input/output pin
-
20
mA
IOL(I/O)
LOW-level output current per
input/output pin
-
20
mA
II/Otot(max)
maximum total input/output current
-
100
mA
Vxtal
crystal voltage
on XTAL1, XTAL2 pin to VSS
Vn
voltage on any other pin
except XTAL1, XTAL2 to VSS
Ptot(pack)
total power dissipation (per package)
based on package heat
transfer, not device power
consumption
[1]
Conditions
Min
Max
Unit
bias ambient temperature
55
+125
C
storage temperature
65
+150
C
0.5
-
VDD + 0.5
V
+5.5
V
1.5
W
The following applies to Table 10:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated
maximum.
b) Parameters are valid over ambient temperature range unless otherwise specified. All voltages are with respect to V SS unless
otherwise noted.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
56 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
11. Static characteristics
Table 11.
Static characteristics
Symbol
Parameter
IDD(oper)
IDD(idle)
Min
Typ[1]
VDD = 3.6 V; fosc = 12 MHz
[2]
-
11
18
mA
VDD = 3.6 V; fosc = 18 MHz
[2]
-
14
23
mA
VDD = 3.6 V; fosc = 12 MHz
[2]
-
3.25
5
mA
VDD = 3.6 V; fosc = 18 MHz
[2]
-
5
7
mA
-
55
80
A
Conditions
operating supply current
Idle mode supply current
Max
Unit
IDD(pd)
Power-down mode supply
current
VDD = 3.6 V; voltage
comparators powered
down
[2]
IDD(tpd)
total Power-down mode supply
current
all devices except
P89LPC933HDH;
VDD = 3.6 V
[3]
-
1
5
A
P89LPC933HDH only;
VDD = 3.6 V
[3]
-
-
25
A
-
-
2
(dV/dt)r
rise rate
of VDD
(dV/dt)f
fall rate
of VDD
VPOR
power-on reset voltage
VDDR
data retention supply voltage
Vth(HL)
HIGH-LOW threshold voltage
except SCL, SDA
VIL
LOW-level input voltage
SCL, SDA only
Vth(LH)
LOW-HIGH threshold voltage
except SCL, SDA
-
VIH
HIGH-level input voltage
SCL, SDA only
0.7VDD
Vhys
hysteresis voltage
port 1
-
VOL
VOH
LOW-level output voltage
HIGH-level output voltage
-
-
50
mV/ s
-
-
0.5
V
1.5
-
-
V
0.22VDD
0.4VDD
-
V
-
0.3VDD
V
0.6VDD
0.7VDD
V
-
5.5
V
0.2VDD
-
V
-
0.6
1.0
V
IOL = 3.2 mA; VDD = 2.4 V
to 3.6 V all ports, all modes
except high-Z
-
0.2
0.3
V
IOH = 20 A;
VDD = 2.4 V to 3.6 V;
all ports,
quasi-bidirectional mode
VDD
0.3
VDD
0.2
-
V
IOH = 3.2 mA;
VDD = 2.4 V to 3.6 V;
all ports, push-pull mode
VDD
0.7
VDD
0.4
-
V
IOH = 10 mA; VDD = 3.6 V;
all ports, push-pull mode
-
3.2
-
V
0.5
-
+4.0
V
0.5
-
+5.5
V
-
15
pF
IOL = 20 mA;
VDD = 2.4 V to 3.6 V
all ports, all modes except
high-Z
Vxtal
crystal voltage
on XTAL1, XTAL2 pins;
with respect to VSS
Vn
voltage on any other pin
except XTAL1, XTAL2,
VDD; with respect to VSS
Ciss
input capacitance
P89LPC933_934_935_936
Product data sheet
mV/ s
0.5
[4]
[5]
[6]
-
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
57 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 11.
Static characteristics
Symbol
Parameter
Conditions
IIL
LOW-level input current
VI = 0.4 V
Min
Typ[1]
Max
Unit
[7]
-
-
80
A
-
-
10
A
-
450
A
ILI
input leakage current
VI = VIL, VIH or Vth(HL)
[8]
ITHL
HIGH-LOW transition current
all ports; VI = 1.5 V at
VDD = 3.6 V
[9]
RRST_N(int) internal pull-up resistance on
pin RST
2.4 V < VDD < 3.6 V; with
BOV = 1, BOPD = 0
30
10
-
30
k
2.40
-
2.70
V
Vbo
brownout trip voltage
Vref(bg)
band gap reference voltage
1.11
1.23
1.34
V
TCbg
band gap temperature
coefficient
-
10
20
ppm/
C
[1]
Typical ratings are not guaranteed. The values listed are at room temperature, 3 V.
[2]
The IDD(oper), IDD(idle), and IDD(pd) specifications are measured using an external clock with the following functions disabled: comparators,
real-time clock, and watchdog timer.
[3]
The IDD(tpd) specification is measured using an external clock with the following functions disabled: comparators, real-time clock,
brownout detect, and watchdog timer.
[4]
See Section 10 “Limiting values” for steady state (non-transient) limits on IOL or IOH. If IOL/IOH exceeds the test condition, VOL/VOH may
exceed the related specification.
[5]
This specification can be applied to pins which have A/D input or analog comparator input functions when the pin is not being used for
those analog functions. When the pin is being used as an analog input pin, the maximum voltage on the pin must be limited to 4.0 V with
respect to VSS.
[6]
Pin capacitance is characterized but not tested.
[7]
Measured with port in quasi-bidirectional mode.
[8]
Measured with port in high-impedance mode.
[9]
Port pins source a transition current when used in quasi-bidirectional mode and externally driven from logic 1 to logic 0. This current is
highest when VI is approximately 2 V.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
58 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
11.1 IOH as a function of VOH
a. Tamb = 25 C; VDD = 3.6 V; push-pull mode
b. Tamb = 25 C; VDD = 2.6 V; push-pull mode
Fig 24. IOH as a function of VOH (typical values)
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
59 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
12. Dynamic characteristics
Table 12.
Dynamic characteristics (12 MHz)
Symbol
Parameter
Conditions
fosc(RC)
internal RC oscillator frequency
fosc(WD)
internal watchdog oscillator
frequency
fosc
oscillator frequency
Tcy(clk)
clock cycle time
fCLKLP
low-power select clock
frequency
Variable clock
fosc = 12 MHz
Unit
Min
Max
Min
7.189
7.557
7.189
Max
320
520
320
520
kHz
7.557 MHz
0
12
-
-
MHz
83
-
-
-
ns
0
8
-
-
MHz
P1.5/RST pin
-
50
-
50
ns
any pin except
P1.5/RST
-
15
-
15
ns
P1.5/RST pin
125
-
125
-
ns
any pin except
P1.5/RST
50
-
50
-
ns
-
ns
see Figure 27
Glitch filter
tgr
tsa
glitch rejection time
signal acceptance time
External clock
tCHCX
clock HIGH time
see Figure 27
33
Tcy(CLK)
tCLCX
33
tCLCX
clock LOW time
see Figure 27
33
Tcy(CLK)
tCHCX
33
-
ns
tCLCH
clock rise time
see Figure 27
-
8
-
8
ns
tCHCL
clock fall time
see Figure 27
-
8
-
8
ns
Shift register (UART mode 0)
TXLXL
serial port clock cycle time
see Figure 25
16Tcy(CLK)
-
1333
-
ns
tQVXH
output data set-up to clock rising see Figure 25
edge time
13Tcy(CLK)
-
1083
-
ns
tXHQX
output data hold after clock
rising edge time
see Figure 25
-
Tcy(CLK) + 20
-
103
ns
tXHDX
input data hold after clock rising
edge time
see Figure 25
-
0
-
0
ns
tXHDV
input data valid to clock rising
edge time
see Figure 25
150
-
150
-
ns
6
0
2.0
MHz
4
-
3.0
MHz
SPI interface
fSPI
TSPICYC
SPI operating frequency
slave
0
CCLK
master
-
CCLK
SPI cycle time
slave
see Figure 26, 28,
29, 30
4
master
tSPILEAD
SPI enable lead time
6
Product data sheet
-
500
-
ns
CCLK
-
333
-
ns
250
-
250
-
ns
see Figure 29, 30
slave
P89LPC933_934_935_936
CCLK
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
60 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 12.
Symbol
tSPILAG
Dynamic characteristics (12 MHz)
Parameter
Conditions
SPI enable lag time
Variable clock
Min
Max
250
-
250
-
ns
CCLK
-
165
-
ns
CCLK
-
250
-
ns
CCLK
-
165
-
ns
CCLK
-
250
-
ns
see Figure 26, 28,
29, 30
100
-
100
-
ns
see Figure 26, 28,
29, 30
100
-
100
-
ns
0
120
0
120
ns
0
240
-
240
ns
-
240
-
240
ns
see Figure 29, 30
SPICLK HIGH time
see Figure 26, 28,
29, 30
master
2
3
slave
tSPICLKL
SPICLK LOW time
see Figure 26, 28,
29, 30
master
2
3
slave
tSPIDSU
SPI data set-up time
tSPIDH
SPI data hold time
tSPIA
SPI access time
tSPIDIS
SPI disable time
tSPIDV
SPI enable to output data valid
time
master or slave
master or slave
see Figure 29, 30
slave
see Figure 29, 30
slave
see Figure 26, 28,
29, 30
slave
master
tSPIOH
SPI output data hold time
see Figure 26, 28,
29, 30
tSPIR
SPI rise time
see Figure 26, 28,
29, 30
SPI outputs
(SPICLK, MOSI, MISO)
SPI inputs
(SPICLK, MOSI, MISO, SS)
tSPIF
SPI fall time
see Figure 26, 28,
29, 30
SPI outputs
(SPICLK, MOSI, MISO)
SPI inputs
(SPICLK, MOSI, MISO, SS)
-
167
-
167
ns
0
-
0
-
ns
-
100
-
100
ns
-
2000
-
2000
ns
-
100
-
100
ns
-
2000
-
2000
ns
[1]
Parameters are valid over ambient temperature range unless otherwise specified.
[2]
Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz.
P89LPC933_934_935_936
Product data sheet
Unit
Max
slave
tSPICLKH
fosc = 12 MHz
Min
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
61 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 13.
Dynamic characteristics (18 MHz)
Symbol
Parameter
fosc(RC)
internal RC oscillator frequency
fosc(WD)
internal watchdog oscillator
frequency
fosc
oscillator frequency
Tcy(CLK)
clock cycle
fCLKLP
low-power select clock
frequency
Conditions
Variable clock
fosc = 18 MHz Unit
Min
Max
Min
7.189
7.557
7.189
320
520
320
520
kHz
see Figure 27
Max
7.557 MHz
0
18
-
-
MHz
55
-
-
-
ns
0
8
-
-
MHz
Glitch filter
tgr
tsa
glitch rejection time
signal acceptance time
P1.5/RST pin
-
50
-
50
ns
any pin except
P1.5/RST
-
15
-
15
ns
P1.5/RST pin
125
-
125
-
ns
any pin except
P1.5/RST
50
-
50
-
ns
-
ns
External clock
tCHCX
clock HIGH time
see Figure 27
22
Tcy(CLK)
tCLCX
22
tCLCX
clock LOW time
see Figure 27
22
Tcy(CLK)
tCHCX
22
-
ns
tCLCH
clock rise time
see Figure 27
-
5
-
5
ns
tCHCL
clock fall time
see Figure 27
-
5
-
5
ns
Shift register (UART mode 0)
TXLXL
serial port clock cycle time
see Figure 25
16Tcy(CLK)
-
888
-
ns
tQVXH
output data set-up to clock
rising edge time
see Figure 25
13Tcy(CLK)
-
722
-
ns
tXHQX
output data hold after clock
rising edge time
see Figure 25
-
Tcy(CLK) + 20
-
75
ns
tXHDX
input data hold after clock rising see Figure 25
edge time
-
0
-
0
ns
tXHDV
input data valid to clock rising
edge time
150
-
150
-
ns
6
0
3.0
MHz
4
-
4.5
MHz
see Figure 25
SPI interface
fSPI
SPI operating frequency
slave
master
TSPICYC
SPI cycle time
slave
see Figure 26, 28,
29, 30
4
master
tSPILEAD
SPI enable lead time
6
SPI enable lag time
Product data sheet
-
CCLK
CCLK
-
333
-
ns
CCLK
-
222
-
ns
250
-
250
-
ns
250
-
250
-
ns
see Figure 29, 30
slave
P89LPC933_934_935_936
CCLK
see Figure 29, 30
slave
tSPILAG
0
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
62 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 13.
Dynamic characteristics (18 MHz)
Symbol
Parameter
Conditions
Variable clock
Min
tSPICLKH
SPICLK HIGH time
see Figure 26, 28,
29, 30
master
3
slave
tSPICLKL
SPICLK LOW time
see Figure 26, 28,
29, 30
master
2
3
slave
tSPIDSU
2
SPI data set-up time
master or slave
tSPIDH
SPI data hold time
tSPIA
SPI access time
tSPIDIS
SPI disable time
tSPIDV
SPI enable to output data valid
time
master or slave
Min
Max
CCLK
-
111
-
ns
CCLK
-
167
-
ns
CCLK
-
111
-
ns
167
-
ns
CCLK
-
see Figure 26, 28,
29, 30
100
-
100
-
ns
see Figure 26, 28,
29, 30
100
-
100
-
ns
0
80
0
80
ns
0
160
-
160
ns
-
160
-
160
ns
see Figure 29, 30
slave
see Figure 29, 30
slave
see Figure 26, 28,
29, 30
slave
master
tSPIOH
SPI output data hold time
see Figure 26, 28,
29, 30
tSPIR
SPI rise time
see Figure 26, 28,
29, 30
SPI outputs
(SPICLK, MOSI, MISO)
-
111
-
111
ns
0
-
0
-
ns
-
100
-
100
ns
-
2000
-
2000
ns
-
100
-
100
ns
-
2000
-
2000
ns
SPI inputs
(SPICLK, MOSI, MISO, SS)
tSPIF
SPI fall time
see Figure 26, 28,
29, 30
SPI outputs
(SPICLK, MOSI, MISO)
SPI inputs
(SPICLK, MOSI, MISO, SS)
[1]
Parameters are valid over ambient temperature range unless otherwise specified.
[2]
Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz.
P89LPC933_934_935_936
Product data sheet
fosc = 18 MHz Unit
Max
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
63 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
12.1 Waveforms
Fig 25. Shift register mode timing
Fig 26. SPI master timing (CPHA = 0)
Fig 27. External clock timing (with an amplitude of at least V i(RMS) = 200 mV)
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
64 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
Fig 28. SPI master timing (CPHA = 1)
Fig 29. SPI slave timing (CPHA = 0)
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
65 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Fig 30. SPI slave timing (CPHA = 1)
12.2 ISP entry mode
Table 14.
Dynamic characteristics, ISP entry mode
Symbol
Parameter
Conditions
Min
Typ
Max
tVR
RST delay from VDD active time
tRH
RST HIGH time
tRL
RST LOW time
1
Unit
50
-
-
s
1
-
32
s
-
-
s
Fig 31. ISP entry timing
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
66 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
13. Other characteristics
13.1 Comparator electrical characteristics
Table 15.
Comparator electrical characteristics
Symbol
Parameter
VIO
input offset voltage
-
-
20
VIC
common-mode input voltage
0
-
VDD
CMRR
common-mode rejection ratio
-
-
50
dB
tres(tot)
total response time
-
250
500
ns
t(CE-OV)
chip enable to output valid time
-
-
10
ILI
input leakage current
-
-
[1]
Conditions
Min
[1]
0 < VI < VDD
Typ
Max
10
Unit
mV
0.3
V
s
A
This parameter is characterized, but not tested in production.
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
67 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
13.2 ADC electrical characteristics
Table 16.
ADC electrical characteristics
Symbol
Parameter
VIA
analog input voltage
Ciss
input capacitance
ED
differential linearity error
EL(adj)
integral non-linearity
EO
offset error
EG
gain error
Eu(tot)
total unadjusted error
MCTC
channel-to-channel matching
ct(port)
crosstalk between port inputs
SRin
input slew rate
Tcy(ADC)
ADC clock cycle time
tADC
ADC conversion time
P89LPC933_934_935_936
Product data sheet
Conditions
0 kHz to 100 kHz
A/D enabled
Min
Typ
Max
Unit
VSS 0.2
-
VDD +0.2
V
-
-
15
-
-
1
LSB
-
-
1
LSB
-
-
2
LSB
-
-
1
%
-
-
2
LSB
-
-
1
LSB
-
-
60
dB
-
-
100
V/ms
111
-
2000
ns
-
-
13Tcy(ADC) ns
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
pF
© NXP B.V. 2011. All rights reserved.
68 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
14. Package outline
PLCC28: plastic leaded chip carrier; 28 leads
SOT261-2
DIMENSIONS (mm dimensions are derived from the original inch dimensions)
A4
A1
b1 D(1) E(1)
bp
A3
e
eD
eE
HD
UNIT A
max.
min.
HE
k
Lp
v
w
y
ZD(1) ZE(1)
max. max.
Note
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
Fig 32. Package outline SOT261-2 (PLCC28)
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
69 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
TSSOP28: plastic thin shrink small outline package; 28 leads; body width 4.4 mm
SOT361-1
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
D (1)
c
E (2)
e
HE
L
Lp
Q
v
w
y
Z (1)
Notes
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
Fig 33. Package outline SOT361-1 (TSSOP28)
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
70 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
HVQFN28: plastic thermal enhanced very thin quad flat package; no leads;
28 terminals; body 6 x 6 x 0.85 mm
8
SOT788-1
14
7
15
1
21
28
22
DIMENSIONS (mm are the original dimensions)
UNIT
A(1)
max.
A1
b
c
D(1)
Dh
E (1)
Eh
e
e1
e2
L
v
w
y
y1
Note
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
Fig 34. Package outline SOT788-1 (HVQFN28)
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
71 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
15. Abbreviations
Table 17.
P89LPC933_934_935_936
Product data sheet
Acronym list
Acronym
Description
A/D
Analog to Digital
CPU
Central Processing Unit
DAC
Digital to Analog Converter
EPROM
Erasable Programmable Read-Only Memory
EEPROM
Electrically Erasable Programmable Read-Only Memory
EMI
Electro-Magnetic Interference
LED
Light Emitting Diode
PWM
Pulse Width Modulator
RAM
Random Access Memory
RC
Resistance-Capacitance
RTC
Real-Time Clock
SAR
Successive Approximation Register
SFR
Special Function Register
SPI
Serial Peripheral Interface
UART
Universal Asynchronous Receiver/Transmitter
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
72 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
16. Revision history
Table 18.
Revision history
Document ID
Release
date
Data sheet status
Change notice Supersedes
P89LPC933_934_ 935_936 v.8
20110112
Product data sheet
-
Modifications:
•
•
•
•
P89LPC933_934_ 935_936 v.7
Table 10 “Limiting values”: Changed Vn max to 5.5 V.
Table 11 “Static characteristics”: Added VPOR.
Table 16 “ADC electrical characteristics”: Corrected VIA max.
Section 8.16 “Reset”: Added sentence “When this pin functions as a reset input....”
P89LPC933_934_ 935_936 v.7
20081126
Product data sheet
-
P89LPC933_934_ 935_936 v.6
P89LPC933_934_ 935_936 v.6
20050620
Product data sheet
-
P89LPC933_934_ 935_936 v.5
P89LPC933_934_ 935_936 v.5
20041103
Product data sheet
-
P89LPC933_934_ 935 v.4
P89LPC933_934_ 935 v.4
20040209
Objective data
-
P89LPC933_934_ 935 v.3
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
73 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
17. Legal information
17.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
17.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
17.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the
of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
P89LPC933_934_935_936
Product data sheet
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
74 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
17.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
18. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
75 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
19. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
2.1
Principal features . . . . . . . . . . . . . . . . . . . . . . . 1
2.2
Additional features . . . . . . . . . . . . . . . . . . . . . . 2
3
Product comparison overview . . . . . . . . . . . . . 3
4
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
4.1
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3
5
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6
Pinning information . . . . . . . . . . . . . . . . . . . . . . 5
6.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 7
7
Logic symbols . . . . . . . . . . . . . . . . . . . . . . . . . 11
8
Functional description . . . . . . . . . . . . . . . . . . 12
8.1
Special function registers . . . . . . . . . . . . . . . . 12
8.2
Enhanced CPU . . . . . . . . . . . . . . . . . . . . . . . . 24
8.3
Clocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.3.1
Clock definitions . . . . . . . . . . . . . . . . . . . . . . . 24
8.3.2
CPU clock (OSCCLK). . . . . . . . . . . . . . . . . . . 24
8.3.3
Low speed oscillator option . . . . . . . . . . . . . . 24
8.3.4
Medium speed oscillator option . . . . . . . . . . . 24
8.3.5
High speed oscillator option . . . . . . . . . . . . . . 24
8.3.6
Clock output . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.4
On-chip RC oscillator option . . . . . . . . . . . . . . 25
8.5
Watchdog oscillator option . . . . . . . . . . . . . . . 25
8.6
External clock input option . . . . . . . . . . . . . . . 25
8.7
CCLK wake-up delay . . . . . . . . . . . . . . . . . . . 27
8.8
CCLK modification: DIVM register . . . . . . . . . 27
8.9
Low power select . . . . . . . . . . . . . . . . . . . . . . 27
8.10
Memory organization . . . . . . . . . . . . . . . . . . . 27
8.11
Data RAM arrangement . . . . . . . . . . . . . . . . . 28
8.12
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.12.1
External interrupt inputs . . . . . . . . . . . . . . . . . 28
8.13
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.13.1
Port configurations . . . . . . . . . . . . . . . . . . . . . 30
8.13.1.1 Quasi-bidirectional output configuration . . . . . 30
8.13.1.2 Open-drain output configuration . . . . . . . . . . . 30
8.13.1.3 Input-only configuration . . . . . . . . . . . . . . . . . 31
8.13.1.4 Push-pull output configuration . . . . . . . . . . . . 31
8.13.2
Port 0 analog functions. . . . . . . . . . . . . . . . . . 31
8.13.3
Additional port features. . . . . . . . . . . . . . . . . . 31
8.14
Power monitoring functions . . . . . . . . . . . . . . 31
8.14.1
Brownout detection . . . . . . . . . . . . . . . . . . . . . 32
8.14.2
Power-on detection. . . . . . . . . . . . . . . . . . . . . 32
8.15
Power reduction modes . . . . . . . . . . . . . . . . . 32
8.15.1
Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.15.2
Power-down mode . . . . . . . . . . . . . . . . . . . . . 32
8.15.3
8.16
8.16.1
8.17
8.17.1
8.17.2
8.17.3
8.17.4
8.17.5
8.17.6
8.18
8.19
8.19.1
8.19.2
8.19.3
8.19.4
8.19.5
8.19.6
8.19.7
8.19.8
8.19.9
8.20
8.20.1
8.20.2
8.20.3
8.20.4
8.20.5
8.20.6
8.20.7
8.20.8
8.20.9
8.20.10
8.21
8.22
8.22.1
8.23
8.23.1
8.23.2
8.23.3
8.24
8.25
8.26
8.26.1
8.26.2
8.27
8.28
Total Power-down mode . . . . . . . . . . . . . . . .
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset vector. . . . . . . . . . . . . . . . . . . . . . . . . .
Timers/counters 0 and 1 . . . . . . . . . . . . . . . .
Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer overflow toggle output . . . . . . . . . . . . .
RTC/system timer . . . . . . . . . . . . . . . . . . . . .
CCU (P89LPC935/936) . . . . . . . . . . . . . . . . .
CCU clock . . . . . . . . . . . . . . . . . . . . . . . . . . .
CCUCLK prescaling. . . . . . . . . . . . . . . . . . . .
Basic timer operation . . . . . . . . . . . . . . . . . . .
Output compare . . . . . . . . . . . . . . . . . . . . . . .
Input capture . . . . . . . . . . . . . . . . . . . . . . . . .
PWM operation . . . . . . . . . . . . . . . . . . . . . . .
Alternating output mode. . . . . . . . . . . . . . . . .
PLL operation. . . . . . . . . . . . . . . . . . . . . . . . .
CCU interrupts . . . . . . . . . . . . . . . . . . . . . . . .
UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Baud rate generator and selection. . . . . . . . .
Framing error . . . . . . . . . . . . . . . . . . . . . . . . .
Break detect. . . . . . . . . . . . . . . . . . . . . . . . . .
Double buffering. . . . . . . . . . . . . . . . . . . . . . .
Transmit interrupts with double
buffering enabled (modes 1, 2 and 3) . . . . . .
The 9th bit (bit 8) in double
buffering (modes 1, 2 and 3) . . . . . . . . . . . . .
I2C-bus serial interface. . . . . . . . . . . . . . . . . .
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical SPI configurations . . . . . . . . . . . . . . .
Analog comparators. . . . . . . . . . . . . . . . . . . .
Internal reference voltage . . . . . . . . . . . . . . .
Comparator interrupt . . . . . . . . . . . . . . . . . . .
Comparators and power reduction modes . . .
Keypad interrupt. . . . . . . . . . . . . . . . . . . . . . .
Watchdog timer . . . . . . . . . . . . . . . . . . . . . . .
Additional features . . . . . . . . . . . . . . . . . . . . .
Software reset . . . . . . . . . . . . . . . . . . . . . . . .
Dual data pointers . . . . . . . . . . . . . . . . . . . . .
Data EEPROM (P89LPC935/936) . . . . . . . . .
Flash program memory . . . . . . . . . . . . . . . . .
33
33
33
34
34
34
34
34
34
34
34
35
35
35
35
35
35
36
37
37
38
38
38
39
39
39
39
39
40
40
40
40
41
43
44
46
46
47
47
47
48
48
48
48
49
49
continued >>
P89LPC933_934_935_936
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
© NXP B.V. 2011. All rights reserved.
76 of 77
P89LPC933/934/935/936
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.28.1
General description . . . . . . . . . . . . . . . . . . . .
8.28.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.28.3
Flash organization . . . . . . . . . . . . . . . . . . . . .
8.28.4
Using flash as data storage . . . . . . . . . . . . . .
8.28.5
Flash programming and erasing . . . . . . . . . . .
8.28.6
In-circuit programming . . . . . . . . . . . . . . . . . .
8.28.7
In-application programming . . . . . . . . . . . . . .
8.28.8
ISP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.28.9
Power-on reset code execution . . . . . . . . . . .
8.28.10 Hardware activation of the boot loader . . . . . .
8.29
User configuration bytes. . . . . . . . . . . . . . . . .
8.30
User sector security bytes . . . . . . . . . . . . . . .
9
A/D converter . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1
General description . . . . . . . . . . . . . . . . . . . .
9.2
Features and benefits . . . . . . . . . . . . . . . . . . .
9.3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . .
9.4
A/D operating modes . . . . . . . . . . . . . . . . . . .
9.4.1
Fixed channel, single conversion mode . . . . .
9.4.2
Fixed channel, continuous conversion mode .
9.4.3
Auto scan, single conversion mode . . . . . . . .
9.4.4
Auto scan, continuous conversion mode . . . .
9.4.5
Dual channel, continuous conversion mode . .
9.4.6
Single step mode . . . . . . . . . . . . . . . . . . . . . .
9.5
Conversion start modes . . . . . . . . . . . . . . . . .
9.5.1
Timer triggered start . . . . . . . . . . . . . . . . . . . .
9.5.2
Start immediately . . . . . . . . . . . . . . . . . . . . . .
9.5.3
Edge triggered . . . . . . . . . . . . . . . . . . . . . . . .
9.5.4
Dual start immediately (P89LPC935/936) . . .
9.6
Boundary limits interrupt . . . . . . . . . . . . . . . . .
9.7
DAC output to a port pin with high output
impedance . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.8
Clock divider . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9
Power-down and Idle mode . . . . . . . . . . . . . .
10
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . .
11
Static characteristics . . . . . . . . . . . . . . . . . . . .
11.1
IOH as a function of VOH . . . . . . . . . . . . . . . . .
12
Dynamic characteristics . . . . . . . . . . . . . . . . .
12.1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.2
ISP entry mode. . . . . . . . . . . . . . . . . . . . . . . .
13
Other characteristics . . . . . . . . . . . . . . . . . . . .
13.1
Comparator electrical characteristics . . . . . . .
13.2
ADC electrical characteristics. . . . . . . . . . . . .
14
Package outline . . . . . . . . . . . . . . . . . . . . . . . .
15
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Revision history . . . . . . . . . . . . . . . . . . . . . . . .
17
Legal information. . . . . . . . . . . . . . . . . . . . . . .
17.1
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
17.2
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.3
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
49
50
50
50
50
50
51
51
52
52
52
52
52
52
53
53
53
54
54
54
54
54
54
54
54
55
55
55
17.4
18
19
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Contact information . . . . . . . . . . . . . . . . . . . . 75
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
55
55
55
56
57
59
60
64
66
67
67
68
69
72
73
74
74
74
74
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 12 January 2011
Document identifier: P89LPC933_934_935_936