P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core,
4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs
Rev. 5.1 — 20 August 2012
Product data sheet
1. General description
The P89LPC9331/9341/9351/9361 is a single-chip microcontroller, available in low cost
packages, based on a high performance processor architecture that executes instructions
in two to four clocks, six times the rate of standard 80C51 devices. Many system-level
functions have been incorporated into the P89LPC9331/9341/9351/9361 in order to
reduce component count, board space, and system cost.
2. Features and benefits
2.1 Principal features
4 kB/8 kB/16 kB byte-erasable flash code memory organized into 1 kB sectors and
64-byte pages. Single-byte erasing allows any byte(s) to be used as non-volatile data
storage.
256-byte RAM data memory. P89LPC9351 and P89LPC9361 also include a 512-byte
auxiliary on-chip RAM.
512-byte customer data EEPROM on-chip allows serialization of devices, storage of
setup parameters, etc. (P89LPC9351/9361)
Dual 4-input multiplexed 8-bit ADC/DAC outputs. Two analog comparators with
selectable inputs and reference source.
Dual Programmable Gain Amplifiers (PGA) with selectable gains of 2x, 4x, 8x, or 16x
can be applied to ADCs and analog comparator inputs. (P89LPC9351/9361)
On-chip temperature sensor integrated with ADC module.
Two 16-bit counter/timers (each may be configured to toggle a port output upon timer
overflow or to become a PWM output).
A 23-bit system timer that can also be used as a real-time clock consisting of a 7-bit
prescaler and a programmable and readable 16-bit timer.
Enhanced UART with a fractional baud rate generator, break detect, framing error
detection, and automatic address detection; 400 kHz byte-wide I2C-bus
communication port and SPI communication port.
Capture/Compare Unit (CCU) provides PWM, input capture, and output compare
functions. (P89LPC9351/9361)
2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or
driven to 5.5 V).
Enhanced low voltage (brownout) detect allows a graceful system shutdown when
power fails.
28-pin TSSOP and PLCC packages with 23 I/O pins minimum and up to 26 I/O pins
while using on-chip oscillator and reset options.
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
2.2 Additional features
A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns
for all instructions except multiply and divide when executing at 18 MHz. This is six
times the performance of the standard 80C51 running at the same clock frequency. A
lower clock frequency for the same performance results in power savings and reduced
EMI.
Serial flash In-Circuit Programming (ICP) allows simple production coding with
commercial EPROM programmers. Flash security bits prevent reading of sensitive
application programs.
Serial flash In-System Programming (ISP) allows coding while the device is mounted
in the end application.
In-Application Programming (IAP) of the flash code memory. This allows changing the
code in a running application.
Watchdog timer with separate on-chip oscillator, nominal 400 kHz, calibrated to 5 %,
requiring no external components. The watchdog prescaler is selectable from
eight values.
High-accuracy internal RC oscillator option, with clock doubler option, allows operation
without external oscillator components. The RC oscillator option is selectable and fine
tunable.
Clock switching on the fly among internal RC oscillator, watchdog oscillator, external
clock source provides optimal support of minimal power active mode with fast
switching to maximum performance.
Idle and two different power-down reduced power modes. Improved wake-up from
Power-down mode (a LOW interrupt input starts execution). Typical power-down
current is 1 A (total power-down with voltage comparators disabled).
Active-LOW reset. On-chip power-on reset allows operation without external reset
components. A software reset function is also available.
Configurable on-chip oscillator with frequency range options selected by user
programmed flash configuration bits. Oscillator options support frequencies from
20 kHz to the maximum operating frequency of 18 MHz.
Oscillator fail detect. The watchdog timer has a separate fully on-chip oscillator
allowing it to perform an oscillator fail detect function.
Programmable port output configuration options: quasi-bidirectional, open drain,
push-pull, input-only.
High current sourcing/sinking (20 mA) on eight I/O pins (P0.3 to P0.7, P1.4, P1.6,
P1.7). All other port pins have high sinking capability (20 mA). A maximum limit is
specified for the entire chip.
Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value of
the pins match or do not match a programmable pattern.
Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns
minimum ramp times.
Only power and ground connections are required to operate the
P89LPC9331/9341/9351/9361 when internal reset option is selected.
Four interrupt priority levels.
Eight keypad interrupt inputs, plus two additional external interrupt inputs.
Schmitt trigger port inputs.
Second data pointer.
Emulation support.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
2 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
3. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
P89LPC9331FDH
TSSOP28
plastic thin shrink small outline package; 28
leads; body width 4.4 mm
SOT361-1
P89LPC9331HDH
TSSOP28
plastic thin shrink small outline package; 28
leads; body width 4.4 mm
SOT361-1
P89LPC9341FDH
TSSOP28
plastic thin shrink small outline package; 28
leads; body width 4.4 mm
SOT361-1
P89LPC9351FA
PLCC28
plastic leaded chip carrier; 28 leads
SOT261-2
P89LPC9351FDH
TSSOP28
plastic thin shrink small outline package; 28
leads; body width 4.4 mm
SOT361-1
P89LPC9361FDH
TSSOP28
plastic thin shrink small outline package; 28
leads; body width 4.4 mm
SOT361-1
3.1 Ordering options
Table 2.
Ordering options
Type number
Flash memory
Temperature range
Frequency
P89LPC9331FDH
4 kB
40 C to +85 C
0 MHz to 18 MHz
P89LPC9331HDH
4 kB
40 C to +125 C
0 MHz to 18 MHz
P89LPC9341FDH
8 kB
40 C to +85 C
0 MHz to 18 MHz
P89LPC9351FA
8 kB
40 C to +85 C
0 MHz to 18 MHz
P89LPC9351FDH
8 kB
40 C to +85 C
0 MHz to 18 MHz
P89LPC9361FDH
16 kB
40 C to +85 C
0 MHz to 18 MHz
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
3 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
4. Block diagram
P89LPC9331/9341/9351/9361
ACCELERATED 2-CLOCK 80C51 CPU
4 kB/8 kB/16 kB
CODE FLASH
512-BYTE
AUXILIARY RAM(1)
P2[7:0]
PORT 2
CONFIGURABLE I/Os
P1[7:0]
PORT 1
CONFIGURABLE I/Os
P0[7:0]
I2C-BUS
SCL
SDA
SPICLK
MOSI
MISO
SS
SPI
REAL-TIME CLOCK/
SYSTEM TIMER
512-BYTE
DATA EEPROM(1)
PORT 3
CONFIGURABLE I/Os
TXD
RXD
internal bus
256-BYTE
DATA RAM
P3[1:0]
UART
T0
T1
TIMER 0
TIMER 1
ANALOG
COMPARATORS
PORT 0
CONFIGURABLE I/Os
KEYPAD
INTERRUPT
CCU (CAPTURE/
COMPARE UNIT)(1)
OCA
OCB
OCC
OCD
ICA
ICB
ADC1/DAC1(2)
AD10
AD11
AD12
AD13
DAC1
ADC0/TEMP
SENSOR/DAC0(3)
AD00
AD01
AD02
AD03
DAC0
WATCHDOG TIMER
AND OSCILLATOR
PROGRAMMABLE
OSCILLATOR DIVIDER
XTAL1
CRYSTAL
OR
RESONATOR XTAL2
CONFIGURABLE
OSCILLATOR
CPU
clock
ON-CHIP RC
OSCILLATOR
WITH CLOCK
DOUBLER
CMP2
CIN2B
CIN2A
CMP1
CIN1A
CIN1B
POWER MONITOR
(POWER-ON RESET,
BROWNOUT RESET)
002aad555
(1) P89LPC9351/9361
(2) PGA1 on P89LPC9351/9361
(3) PGA0 on P89LPC9351/9361
Fig 1.
Block diagram
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
4 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
5. Functional diagram
VDD
DAC1
KBI0
KBI1
KBI2
KBI3
KBI4
KBI5
KBI6
KBI7
CMP2
CIN2B
CIN2A
CIN1B
CIN1A
CMPREF
CMP1
T1
CLKOUT
XTAL2
AD01
AD10
AD11
AD12
AD13
VSS
PORT 0
TXD
RXD
T0
INT0
INT1
RST
AD00
PORT 1
P89LPC9331/
P89LPC9341
SCL
SDA
DAC0
AD03
AD02
MOSI
MISO
SS
SPICLK
PORT 3
XTAL1
PORT 2
002aae461
Fig 2.
Functional diagram (P89LPC9331/9341)
VDD
DAC1
AD01
AD10
AD11
AD12
AD13
KBI0
KBI1
KBI2
KBI3
KBI4
KBI5
KBI6
KBI7
CMP2
CIN2B
CIN2A
CIN1B
CIN1A
CMPREF
CMP1
T1
CLKOUT
XTAL2
VSS
PORT 0
PORT 1
P89LPC9351/
P89LPC9361
PORT 3
XTAL1
PORT 2
TXD
RXD
T0
INT0
INT1
RST
OCB
OCC
ICB
OCD
MOSI
MISO
SS
SPICLK
OCA
ICA
SCL
SDA
AD00
AD03
AD02
DAC0
002aad556
Fig 3.
Functional diagram (P89LPC9351/9361)
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
5 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
6. Pinning information
6.1 Pinning
P2.0/AD03/DAC0
1
28 P2.7
P2.1/AD02
2
27 P2.6
P0.0/CMP2/KBI0/AD01
3
26 P0.1/CIN2B/KBI1/AD10
P1.7/AD00
4
25 P0.2/CIN2A/KBI2/AD11
P1.6
5
24 P0.3/CIN1B/KBI3/AD12
P1.5/RST
6
23 P0.4/CIN1A/KBI4/DAC1/AD13
VSS
7
P3.1/XTAL1
8
P3.0/XTAL2/CLKOUT
9
22 P0.5/CMPREF/KBI5
P89LPC9331FDH/
P89LPC9341FDH
21 VDD
20 P0.6/CMP1/KBI6
P1.4/INT1 10
19 P0.7/T1/KBI7
P1.3/INT0/SDA 11
18 P1.0/TXD
P1.2/T0/SCL 12
17 P1.1/RXD
P2.2/MOSI 13
16 P2.5/SPICLK
P2.3/MISO 14
15 P2.4/SS
002aae462
Fig 4.
P89LPC9331/9341 TSSOP28 pin configuration
P2.0/ICB/DAC0/AD03
1
28 P2.7/ICA
P2.1/OCD/AD02
2
27 P2.6/OCA
P0.0/CMP2/KBI0/AD01
3
26 P0.1/CIN2B/KBI1/AD10
P1.7/OCC/AD00
4
25 P0.2/CIN2A/KBI2/AD11
P1.6/OCB
5
24 P0.3/CIN1B/KBI3/AD12
P1.5/RST
6
23 P0.4/CIN1A/KBI4/DAC1/AD13
VSS
7
P3.1/XTAL1
8
P3.0/XTAL2/CLKOUT
9
P89LPC9351FDH/
P89LPC9361FDH
P1.4/INT1 10
22 P0.5/CMPREF/KBI5
21 VDD
20 P0.6/CMP1/KBI6
19 P0.7/T1/KBI7
P1.3/INT0/SDA 11
18 P1.0/TXD
P1.2/T0/SCL 12
17 P1.1/RXD
P2.2/MOSI 13
16 P2.5/SPICLK
P2.3/MISO 14
15 P2.4/SS
002aad557
Fig 5.
P89LPC9351/9361 TSSOP28 pin configuration
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
6 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
P2.0/ICB/DAC0/AD03
1
26 P0.1/CIN2B/KBI1/AD10
P2.1/OCD/AD02
2
27 P2.6/OCA
P0.0/CMP2/KBI0/AD01
3
28 P2.7/ICA
P1.7/OCC/AD00
4
8-bit microcontroller with accelerated two-clock 80C51 core
P1.6/OCB
5
25 P0.2/CIN2A/KBI2/AD11
P1.5/RST
6
24 P0.3/CIN1B/KBI3/AD12
VSS
7
23 P0.4/CIN1A/KBI4/DAC1/AD13
P3.1/XTAL1
8
P3.0/XTAL2/CLKOUT
9
22 P0.5/CMPREF/KBI5
P89LPC9351FA
21 VDD
20 P0.6/CMP1/KBI6
P1.4/INT1 10
19 P0.7/T1/KBI7
Fig 6.
P1.0/TXD 18
P1.1/RXD 17
P2.5/SPICLK 16
P2.4/SS 15
P2.3/MISO 14
P2.2/MOSI 13
P1.2/T0/SCL 12
P1.3/INT0/SDA 11
002aad558
P89LPC9351 PLCC28 pin configuration
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
7 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
6.2 Pin description
Table 3.
Pin description
Symbol
Pin
Type Description
PLCC28,
TSSOP28
P0.0 to P0.7
I/O
Port 0: Port 0 is an 8-bit I/O port with a user-configurable output type. During reset
Port 0 latches are configured in the input only mode with the internal pull-up
disabled. The operation of Port 0 pins as inputs and outputs depends upon the port
configuration selected. Each port pin is configured independently. Refer to Section
7.16.1 “Port configurations” and Table 12 “Static characteristics” for details.
The Keypad Interrupt feature operates with Port 0 pins.
All pins have Schmitt trigger inputs.
Port 0 also provides various special functions as described below:
P0.0/CMP2/
KBI0/AD01
P0.1/CIN2B/
KBI1/AD10
P0.2/CIN2A/
KBI2/AD11
P0.3/CIN1B/
KBI3/AD12
P0.4/CIN1A/
KBI4/DAC1/AD13
P0.5/CMPREF/
KBI5
3
26
25
24
23
22
I/O
P0.0 — Port 0 bit 0.
O
CMP2 — Comparator 2 output
I
KBI0 — Keyboard input 0.
I
AD01 — ADC0 channel 1 analog input.
I/O
P0.1 — Port 0 bit 1.
I
CIN2B — Comparator 2 positive input B.
I
KBI1 — Keyboard input 1.
I
AD10 — ADC1 channel 0 analog input.
I/O
P0.2 — Port 0 bit 2.
I
CIN2A — Comparator 2 positive input A.
I
KBI2 — Keyboard input 2.
I
AD11 — ADC1 channel 1 analog input.
I/O
P0.3 — Port 0 bit 3. High current source.
I
CIN1B — Comparator 1 positive input B.
I
KBI3 — Keyboard input 3.
I
AD12 — ADC1 channel 2 analog input.
I/O
P0.4 — Port 0 bit 4. High current source.
I
CIN1A — Comparator 1 positive input A.
I
KBI4 — Keyboard input 4.
O
DAC1 — Digital-to-analog converter output 1.
I
AD13 — ADC1 channel 3 analog input.
I/O
P0.5 — Port 0 bit 5. High current source.
I
CMPREF — Comparator reference (negative) input.
I
KBI5 — Keyboard input 5.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
8 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 3.
Pin description …continued
Symbol
Pin
Type Description
PLCC28,
TSSOP28
P0.6/CMP1/KBI6
P0.7/T1/KBI7
20
19
I/O
P0.6 — Port 0 bit 6. High current source.
O
CMP1 — Comparator 1 output.
I
KBI6 — Keyboard input 6.
I/O
P0.7 — Port 0 bit 7. High current source.
I/O
T1 — Timer/counter 1 external count input or overflow output.
I
KBI7 — Keyboard input 7.
I/O, I Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type, except for
[1]
three pins as noted below. During reset Port 1 latches are configured in the input
only mode with the internal pull-up disabled. The operation of the configurable
Port 1 pins as inputs and outputs depends upon the port configuration selected.
Each of the configurable port pins are programmed independently. Refer to
Section 7.16.1 “Port configurations” and Table 12 “Static characteristics” for
details. P1.2 to P1.3 are open drain when used as outputs. P1.5 is input only.
P1.0 to P1.7
All pins have Schmitt trigger inputs.
Port 1 also provides various special functions as described below:
P1.0/TXD
P1.1/RXD
P1.2/T0/SCL
P1.3/INT0/SDA
18
17
12
11
P1.4/INT1
10
P1.5/RST
6
P1.6/OCB
P1.7/OCC/AD00
5
4
I/O
P1.0 — Port 1 bit 0.
O
TXD — Transmitter output for serial port.
I/O
P1.1 — Port 1 bit 1.
I
RXD — Receiver input for serial port.
I/O
P1.2 — Port 1 bit 2 (open-drain when used as output).
I/O
T0 — Timer/counter 0 external count input or overflow output (open-drain when
used as output).
I/O
SCL — I2C-bus serial clock input/output.
I/O
P1.3 — Port 1 bit 3 (open-drain when used as output).
I
INT0 — External interrupt 0 input.
I/O
SDA — I2C-bus serial data input/output.
I/O
P1.4 — Port 1 bit 4. High current source.
I
INT1 — External interrupt 1 input.
I
P1.5 — Port 1 bit 5 (input only).
I
RST — External Reset input during power-on or if selected via UCFG1. When
functioning as a reset input, a LOW on this pin resets the microcontroller, causing
I/O ports and peripherals to take on their default states, and the processor begins
execution at address 0. Also used during a power-on sequence to force ISP mode.
I/O
P1.6 — Port 1 bit 6. High current source.
O
OCB — Output Compare B. (P89LPC9351/9361)
I/O
P1.7 — Port 1 bit 7. High current source.
O
OCC — Output Compare C. (P89LPC9351/9361)
I
AD00 — ADC0 channel 0 analog input.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
9 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 3.
Pin description …continued
Symbol
Pin
Type Description
PLCC28,
TSSOP28
P2.0 to P2.7
I/O
Port 2: Port 2 is an 8-bit I/O port with a user-configurable output type. During reset
Port 2 latches are configured in the input only mode with the internal pull-up
disabled. The operation of Port 2 pins as inputs and outputs depends upon the port
configuration selected. Each port pin is configured independently. Refer to Section
7.16.1 “Port configurations” and Table 12 “Static characteristics” for details.
All pins have Schmitt trigger inputs.
Port 2 also provides various special functions as described below:
P2.0/ICB/DAC0
/AD03
P2.1/OCD/AD02
P2.2/MOSI
P2.3/MISO
P2.4/SS
P2.5/SPICLK
P2.6/OCA
P2.7/ICA
1
2
13
14
15
16
27
28
P3.0 to P3.1
I/O
P2.0 — Port 2 bit 0.
I
ICB — Input Capture B. (P89LPC9351/9361)
O
DAC0 — Digital-to-analog converter output.
I
AD03 — ADC0 channel 3 analog input.
I/O
P2.1 — Port 2 bit 1.
O
OCD — Output Compare D. (P89LPC9351/9361)
I
AD02 — ADC0 channel 2 analog input.
I/O
P2.2 — Port 2 bit 2.
I/O
MOSI — SPI master out slave in. When configured as master, this pin is output;
when configured as slave, this pin is input.
I/O
P2.3 — Port 2 bit 3.
I/O
MISO — When configured as master, this pin is input, when configured as slave,
this pin is output.
I/O
P2.4 — Port 2 bit 4.
I
SS — SPI Slave select.
I/O
P2.5 — Port 2 bit 5.
I/O
SPICLK — SPI clock. When configured as master, this pin is output; when
configured as slave, this pin is input.
I/O
P2.6 — Port 2 bit 6.
O
OCA — Output Compare A. (P89LPC9351/9361)
I/O
P2.7 — Port 2 bit 7.
I
ICA — Input Capture A. (P89LPC9351/9361)
I/O
Port 3: Port 3 is a 2-bit I/O port with a user-configurable output type. During reset
Port 3 latches are configured in the input only mode with the internal pull-up
disabled. The operation of Port 3 pins as inputs and outputs depends upon the port
configuration selected. Each port pin is configured independently. Refer to Section
7.16.1 “Port configurations” and Table 12 “Static characteristics” for details.
All pins have Schmitt trigger inputs.
Port 3 also provides various special functions as described below:
P3.0/XTAL2/
CLKOUT
9
I/O
P3.0 — Port 3 bit 0.
O
XTAL2 — Output from the oscillator amplifier (when a crystal oscillator option is
selected via the flash configuration.
O
CLKOUT — CPU clock divided by 2 when enabled via SFR bit (ENCLK -TRIM.6).
It can be used if the CPU clock is the internal RC oscillator, watchdog oscillator or
external clock input, except when XTAL1/XTAL2 are used to generate clock source
for the RTC/system timer.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
10 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 3.
Pin description …continued
Symbol
Pin
Type Description
PLCC28,
TSSOP28
P3.1/XTAL1
8
I/O
P3.1 — Port 3 bit 1.
I
XTAL1 — Input to the oscillator circuit and internal clock generator circuits (when
selected via the flash configuration). It can be a port pin if internal RC oscillator or
watchdog oscillator is used as the CPU clock source, and if XTAL1/XTAL2 are not
used to generate the clock for the RTC/system timer.
VSS
7
I
Ground: 0 V reference.
VDD
21
I
Power supply: This is the power supply voltage for normal operation as well as
Idle and Power-down modes.
[1]
Input/output for P1.0 to P1.4, P1.6, P1.7. Input for P1.5.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
11 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7. Functional description
Remark: Please refer to the P89LPC9331/9341/9351/9361 User manual for a more
detailed functional description.
7.1 Special function registers
Remark: SFR accesses are restricted in the following ways:
• User must not attempt to access any SFR locations not defined.
• Accesses to any defined SFR locations must be strictly for the functions for the SFRs.
• SFR bits labeled ‘-’, ‘0’ or ‘1’ can only be written and read as follows:
– ‘-’ Unless otherwise specified, must be written with ‘0’, but can return any value
when read (even if it was written with ‘0’). It is a reserved bit and may be used in
future derivatives.
– ‘0’ must be written with ‘0’, and will return a ‘0’ when read.
– ‘1’ must be written with ‘1’, and will return a ‘1’ when read.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
12 of 94
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 4.
Special function registers - P89LPC9331/9341
* indicates SFRs that are bit addressable.
Name
Description
SFR Bit functions and addresses
addr.
MSB
Bit address
E7
E6
E5
Reset value
LSB
E4
E3
E2
E1
Hex
Binary
00
0000 0000
E0
E0H
ADCON0
A/D control
register 0
8EH
ENBI0
ENADCI0
TMM0
EDGE0
ADCI0
ENADC0
ADCS01
ADCS00
00
0000 0000
ADCON1
A/D control
register 1
97H
ENBI1
ENADCI1
TMM1
EDGE1
ADCI1
ENADC1
ADCS11
ADCS10
00
0000 0000
ADINS
A/D input
select
A3H
ADI13
ADI12
ADI11
ADI10
ADI03
ADI02
ADI01
ADI00
00
0000 0000
ADMODA
A/D mode
register A
C0H
BNDI1
BURST1
SCC1
SCAN1
BNDI0
BURST0
SCC0
SCAN0
00
0000 0000
ADMODB
A/D mode
register B
A1H
CLK2
CLK1
CLK0
INBND0
ENDAC1
ENDAC0
BSA1
BSA0
00
000x 0000
AD0BH
A/D_0
boundary high
register
BBH
FF
1111 1111
AD0BL
A/D_0
boundary low
register
A6H
00
0000 0000
AD0DAT0
A/D_0 data
register 0
C5H
00
0000 0000
AD0DAT1
A/D_0 data
register 1
C6H
00
0000 0000
AD0DAT2
A/D_0 data
register 2
C7H
00
0000 0000
AD0DAT3
A/D_0 data
register 3
F4H
00
0000 0000
AD1BH
A/D_1
boundary high
register
C4H
FF
1111 1111
AD1BL
A/D_1
boundary low
register
BCH
00
0000 0000
P89LPC9331/9341/9351/9361
13 of 94
© NXP B.V. 2012. All rights reserved.
Accumulator
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
ACC*
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
A/D_1 data
register 0
D5H
00
0000 0000
AD1DAT1
A/D_1 data
register 1
D6H
00
0000 0000
AD1DAT2
A/D_1 data
register 2
D7H
00
0000 0000
AD1DAT3
A/D_1 data
register 3
F5H
00
0000 0000
AUXR1
Auxiliary
function
register
A2H
00
0000 00x0
CLKLP
EBRR
ENT1
ENT0
SRST
0
-
DPS
F7
F6
F5
F4
F3
F2
F1
F0
B register
F0H
00
0000 0000
Baud rate
generator 0
rate low
BEH
00
0000 0000
BRGR1[2]
Baud rate
generator 0
rate high
BFH
00
0000 0000
BRGCON
Baud rate
generator 0
control
BDH
-
-
-
-
-
-
SBRGS
BRGEN
00[2]
xxxx xx00
CMP1
Comparator 1
control register
ACH
-
-
CE1
CP1
CN1
OE1
CO1
CMF1
00[1]
xx00 0000
CMP2
Comparator 2
control register
ADH
-
-
CE2
CP2
CN2
OE2
CO2
CMF2
00[1]
xx00 0000
DIVM
CPU clock
divide-by-M
control
95H
00
0000 0000
DPTR
Data pointer
(2 bytes)
83H
00
0000 0000
DPH
Data pointer
high
P89LPC9331/9341/9351/9361
14 of 94
© NXP B.V. 2012. All rights reserved.
B*
BRGR0[2]
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
AD1DAT0
Bit address
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 4.
Special function registers - P89LPC9331/9341 …continued
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
DPL
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
00
0000 0000
FMADRH
Program flash
address high
E7H
00
0000 0000
FMADRL
Program flash
address low
E6H
00
0000 0000
FMCON
Program flash
control (Read)
E4H
BUSY
-
-
-
HVA
HVE
SV
OI
70
0111 0000
Program flash
control (Write)
E4H
FMCMD.7
FMCMD.6
FMCMD.5
FMCMD.4
FMCMD.3
FMCMD.2
FMCMD.1
FMCMD.0
FMDATA
Program flash
data
E5H
00
0000 0000
I2ADR
I2C-bus slave
address
register
DBH
00
0000 0000
I2CON*
I2C-bus
00
x000 00x0
control
D8H
I2ADR.6
I2ADR.5
I2ADR.4
I2ADR.3
I2ADR.2
I2ADR.1
I2ADR.0
GC
DF
DE
DD
DC
DB
DA
D9
D8
-
I2EN
STA
STO
SI
AA
-
CRSEL
register
15 of 94
© NXP B.V. 2012. All rights reserved.
I2DAT
I2C-bus data
register
DAH
I2SCLH
Serial clock
generator/SCL
duty cycle
register high
DDH
00
0000 0000
I2SCLL
Serial clock
generator/SCL
duty cycle
register low
DCH
00
0000 0000
I2STAT
I2C-bus status
register
D9H
F8
1111 1000
00
0000 0000
Bit address
IEN0*
Interrupt
enable 0
A8H
Bit address
STA.4
STA.3
STA.2
STA.1
STA.0
0
0
0
AF
AE
AD
AC
AB
AA
A9
A8
EA
EWDRT
EBO
ES/ESR
ET1
EX1
ET0
EX0
EF
EE
ED
EC
EB
EA
E9
E8
P89LPC9331/9341/9351/9361
82H
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
Data pointer
low
Bit address
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 4.
Special function registers - P89LPC9331/9341 …continued
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
IEN1*
Description
Interrupt
enable 1
SFR Bit functions and addresses
addr.
MSB
E8H
Bit address
Reset value
LSB
Hex
Binary
00[1]
00x0 0000
EAD
EST
-
-
ESPI
EC
EKBI
EI2C
BF
BE
BD
BC
BB
BA
B9
B8
IP0*
Interrupt
priority 0
B8H
-
PWDRT
PBO
PS/PSR
PT1
PX1
PT0
PX0
00[1]
x000 0000
IP0H
Interrupt
priority 0 high
B7H
-
PWDRTH
PBOH
PSH/
PSRH
PT1H
PX1H
PT0H
PX0H
00[1]
x000 0000
FF
FE
FD
FC
FB
FA
F9
F8
Bit address
F8H
PAD
PST
-
-
PSPI
PC
PKBI
PI2C
00[1]
00x0 0000
IP1H
Interrupt
priority 1 high
F7H
PADH
PSTH
-
-
PSPIH
PCH
PKBIH
PI2CH
00[1]
00x0 0000
KBCON
Keypad control
register
94H
-
-
-
-
-
-
PATN
_SEL
KBIF
00[1]
xxxx xx00
KBMASK
Keypad
interrupt mask
register
86H
00
0000 0000
KBPATN
Keypad pattern
register
93H
FF
1111 1111
P0*
Port 0
80H
Bit address
P1*
Port 1
P2*
Port 2
90H
Bit address
A0H
16 of 94
© NXP B.V. 2012. All rights reserved.
Bit address
87
86
85
84
83
82
81
80
T1/KB7
CMP1
/KB6
CMPREF
/KB5
CIN1A
/KB4
CIN1B
/KB3
CIN2A
/KB2
CIN2B
/KB1
CMP2
/KB0
97
96
95
94
93
92
91
90
-
-
RST
INT1
INT0/SDA
T0/SCL
RXD
TXD
A7
A6
A5
A4
A3
A2
A1
A0
-
-
SPICLK
SS
MISO
MOSI
-
-
B7
B6
B5
B4
B3
B2
B1
B0
[1]
[1]
[1]
[1]
P3*
Port 3
B0H
-
-
-
-
-
-
XTAL1
XTAL2
P0M1
Port 0 output
mode 1
84H
(P0M1.7)
(P0M1.6)
(P0M1.5)
(P0M1.4)
(P0M1.3)
(P0M1.2)
(P0M1.1)
(P0M1.0)
FF[1]
1111 1111
P0M2
Port 0 output
mode 2
85H
(P0M2.7)
(P0M2.6)
(P0M2.5)
(P0M2.4)
(P0M2.3)
(P0M2.2)
(P0M2.1)
(P0M2.0)
00[1]
0000 0000
P89LPC9331/9341/9351/9361
Interrupt
priority 1
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
IP1*
Bit address
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 4.
Special function registers - P89LPC9331/9341 …continued
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
Hex
Binary
11x1 xx11
91H
(P1M1.7)
(P1M1.6)
-
(P1M1.4)
(P1M1.3)
(P1M1.2)
(P1M1.1)
(P1M1.0)
P1M2
Port 1 output
mode 2
92H
(P1M2.7)
(P1M2.6)
-
(P1M2.4)
(P1M2.3)
(P1M2.2)
(P1M2.1)
(P1M2.0)
00[1]
00x0 xx00
P2M1
Port 2 output
mode 1
A4H
(P2M1.7)
(P2M1.6)
(P2M1.5)
(P2M1.4)
(P2M1.3)
(P2M1.2)
(P2M1.1)
(P2M1.0)
FF[1]
1111 1111
P2M2
Port 2 output
mode 2
A5H
(P2M2.7)
(P2M2.6)
(P2M2.5)
(P2M2.4)
(P2M2.3)
(P2M2.2)
(P2M2.1)
(P2M2.0)
00[1]
0000 0000
P3M1
Port 3 output
mode 1
B1H
-
-
-
-
-
-
(P3M1.1)
(P3M1.0)
03[1]
xxxx xx11
P3M2
Port 3 output
mode 2
B2H
-
-
-
-
-
-
(P3M2.1)
(P3M2.0)
00[1]
xxxx xx00
PCON
Power control
register
87H
SMOD1
SMOD0
-
BOI
GF1
GF0
PMOD1
PMOD0
00
0000 0000
PCONA
Power control
register A
B5H
RTCPD
-
VCPD
ADPD
I2PD
SPPD
SPD
-
00[1]
0000 0000
D7
D6
D5
D4
D3
D2
D1
D0
PSW*
Program status
word
D0H
CY
AC
F0
RS1
RS0
OV
F1
P
00
0000 0000
PT0AD
Port 0 digital
input disable
F6H
-
-
PT0AD.5
PT0AD.4
PT0AD.3
PT0AD.2
PT0AD.1
-
00
xx00 000x
RSTSRC
Reset source
register
DFH
-
BOIF
BOF
POF
R_BK
R_WD
R_SF
R_EX
[3]
RTCCON
RTC control
D1H
RTCF
RTCS1
RTCS0
-
-
-
ERTC
RTCEN
60[1][6]
011x xx00
0000 0000
17 of 94
© NXP B.V. 2012. All rights reserved.
RTCH
RTC register
high
D2H
00[6]
RTCL
RTC register
low
D3H
00[6]
0000 0000
SADDR
Serial port
address
register
A9H
00
0000 0000
SADEN
Serial port
address enable
B9H
00
0000 0000
P89LPC9331/9341/9351/9361
Port 1 output
mode 1
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
P1M1
D3[1]
Bit address
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 4.
Special function registers - P89LPC9331/9341 …continued
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
SBUF
Description
Serial Port data
buffer register
SFR Bit functions and addresses
addr.
MSB
Reset value
LSB
99H
Bit address
9F
9E
9D
9C
9B
9A
99
98
Hex
Binary
xx
xxxx xxxx
98H
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
00
0000 0000
SSTAT
Serial port
extended
status register
BAH
DBMOD
INTLO
CIDIS
DBISEL
FE
BR
OE
STINT
00
0000 0000
SP
Stack pointer
81H
07
0000 0111
SPCTL
SPI control
register
E2H
SSIG
SPEN
DORD
MSTR
CPOL
CPHA
SPR1
SPR0
04
0000 0100
SPSTAT
SPI status
register
E1H
SPIF
WCOL
-
-
-
-
-
-
00
00xx xxxx
SPDAT
SPI data
register
E3H
00
0000 0000
TAMOD
Timer 0 and 1
auxiliary mode
8FH
00
xxx0 xxx0
00
0000 0000
-
-
-
T1M2
-
-
-
T0M2
8F
8E
8D
8C
8B
8A
89
88
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
18 of 94
© NXP B.V. 2012. All rights reserved.
TCON*
Timer 0 and 1
control
88H
TH0
Timer 0 high
8CH
00
0000 0000
TH1
Timer 1 high
8DH
00
0000 0000
TL0
Timer 0 low
8AH
00
0000 0000
TL1
Timer 1 low
8BH
00
0000 0000
TMOD
Timer 0 and 1
mode
89H
T1GATE
T1C/T
T1M1
T1M0
T0GATE
T0C/T
T0M1
T0M0
00
0000 0000
TRIM
Internal
oscillator trim
register
96H
RCCLK
ENCLK
TRIM.5
TRIM.4
TRIM.3
TRIM.2
TRIM.1
TRIM.0
[5][6]
WDCON
Watchdog
control register
A7H
PRE2
PRE1
PRE0
-
-
WDRUN
WDTOF
WDCLK
[4][6]
P89LPC9331/9341/9351/9361
Serial port
control
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
SCON*
Bit address
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 4.
Special function registers - P89LPC9331/9341 …continued
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR Bit functions and addresses
addr.
MSB
WDL
Watchdog load
C1H
WFEED1
Watchdog
feed 1
C2H
WFEED2
Watchdog
feed 2
C3H
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 4.
Special function registers - P89LPC9331/9341 …continued
* indicates SFRs that are bit addressable.
Reset value
LSB
Hex
Binary
FF
1111 1111
All ports are in input only (high-impedance) state after power-up.
[2]
BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable.
[3]
The RSTSRC register reflects the cause of the P89LPC9331/9341 reset except BOIF bit. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the
power-on reset value is x011 0000.
[4]
After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset.
Other resets will not affect WDTOF.
On power-on reset and watchdog reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register.
[6]
The only reset sources that affect these SFRs are power-on reset and watchdog reset.
19 of 94
© NXP B.V. 2012. All rights reserved.
P89LPC9331/9341/9351/9361
[5]
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
[1]
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 5.
Extended special function registers - P89LPC9331/9341[1]
Description
SFR
addr.
Bit functions and addresses
Reset value
BODCFG
BOD
configuration
register
FFC8H
-
-
-
-
-
-
CLKCON
CLOCK Control
register
FFDEH
CLKOK
-
-
XTALWD
CLKDBL
FOSC2
FOSC1
FOSC0
[3]
TPSCON
Temperature
sensor control
register
FFCAH
-
-
-
-
TSEL1
TSEL0
-
-
00
0000 0000
RTCDATH
Real-time clock
data register
high
FFBFH
00
0000 0000
RTCDATL
Real-time clock FFBEH
data register low
00
0000 0000
MSB
LSB
BOICFG1 BOICFG0
Hex
Binary
[2]
Extended SFRs are physically located on-chip but logically located in external data memory address space (XDATA). The MOVX A,@DPTR and MOVX @DPTR,A instructions are
used to access these extended SFRs.
[2]
The BOICFG1/0 will be copied from UCFG1.5 and UCFG1.3 when power-on reset.
[3]
CLKCON register reset value comes from UCFG1 and UCFG2. The reset value of CLKCON.2 to CLKCON.0 come from UCFG1.2 to UCFG1.0 and reset value of CLKDBL bit
comes from UCFG2.7.
20 of 94
© NXP B.V. 2012. All rights reserved.
P89LPC9331/9341/9351/9361
[1]
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
Name
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 6.
Special function registers - P89LPC9351/9361
* indicates SFRs that are bit addressable.
Name
Description
SFR
addr.
Bit address
Bit functions and addresses
Reset value
MSB
E7
LSB
E6
E5
E4
E3
E2
E1
Hex
Binary
00
0000 0000
E0
ACC*
Accumulator
E0H
ADCON0
A/D control
register 0
8EH
ENBI0
ENADCI0
TMM0
EDGE0
ADCI0
ENADC0
ADCS01
ADCS00
00
0000 0000
ADCON1
A/D control
register 1
97H
ENBI1
ENADCI1
TMM1
EDGE1
ADCI1
ENADC1
ADCS11
ADCS10
00
0000 0000
A3H
ADI13
ADI12
ADI11
ADI10
ADI03
ADI02
ADI01
ADI00
00
0000 0000
A/D mode
register A
C0H
BNDI1
BURST1
SCC1
SCAN1
BNDI0
BURST0
SCC0
SCAN0
00
0000 0000
ADMODB
A/D mode
register B
A1H
CLK2
CLK1
CLK0
INBND0
ENDAC1
ENDAC0
BSA1
BSA0
00
000x 0000
AD0BH
A/D_0 boundary
high register
BBH
FF
1111 1111
AD0BL
A/D_0 boundary
low register
A6H
00
0000 0000
AD0DAT0
A/D_0 data
register 0
C5H
00
0000 0000
AD0DAT1
A/D_0 data
register 1
C6H
00
0000 0000
AD0DAT2
A/D_0 data
register 2
C7H
00
0000 0000
AD0DAT3
A/D_0 data
register 3
F4H
00
0000 0000
AD1BH
A/D_1 boundary
high register
C4H
FF
1111 1111
AD1BL
A/D_1 boundary
low register
BCH
00
0000 0000
AD1DAT0
A/D_1 data
register 0
D5H
00
0000 0000
AD1DAT1
A/D_1 data
register 1
D6H
00
0000 0000
AD1DAT2
A/D_1 data
register 2
D7H
00
0000 0000
P89LPC9331/9341/9351/9361
21 of 94
© NXP B.V. 2012. All rights reserved.
A/D input select
ADMODA
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
ADINS
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR
addr.
Bit functions and addresses
Reset value
MSB
LSB
Hex
Binary
00
0000 0000
00
0000 00x0
F5H
AUXR1
Auxiliary function
register
A2H
B*
B register
F0H
00
0000 0000
BRGR0[2]
Baud rate
generator 0 rate
low
BEH
00
0000 0000
BRGR1[2]
Baud rate
generator 0 rate
high
BFH
00
0000 0000
BRGCON
Baud rate
generator 0
control
BDH
-
-
-
-
-
-
SBRGS
BRGEN
00[2]
xxxx xx00
CCCRA
Capture compare
A control register
EAH
ICECA2
ICECA1
ICECA0
ICESA
ICNFA
FCOA
OCMA1
OCMA0
00
0000 0000
CCCRB
Capture compare
B control register
EBH
ICECB2
ICECB1
ICECB0
ICESB
ICNFB
FCOB
OCMB1
OCMB0
00
0000 0000
CCCRC
Capture compare
C control register
ECH
-
-
-
-
-
FCOC
OCMC1
OCMC0
00
xxxx x000
CCCRD
Capture compare
D control register
EDH
-
-
-
-
-
FCOD
OCMD1
OCMD0
00
xxxx x000
CMP1
Comparator 1
control register
ACH
-
-
CE1
CP1
CN1
OE1
CO1
CMF1
00[1]
xx00 0000
CMP2
Comparator 2
control register
ADH
-
-
CE2
CP2
CN2
OE2
CO2
CMF2
00[1]
xx00 0000
DEECON
Data EEPROM
control register
F1H
EEIF
HVERR
ECTL1
ECTL0
-
EWERR1
EWERR0
EADR8
80
1000 0000
DEEDAT
Data EEPROM
data register
F2H
00
0000 0000
DEEADR
Data EEPROM
address register
F3H
00
0000 0000
CLKLP
EBRR
ENT1
ENT0
SRST
0
-
DPS
F7
F6
F5
F4
F3
F2
F1
F0
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
22 of 94
© NXP B.V. 2012. All rights reserved.
P89LPC9331/9341/9351/9361
A/D_1 data
register 3
8-bit microcontroller with accelerated two-clock 80C51 core
AD1DAT3
Bit address
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 6.
Special function registers - P89LPC9351/9361
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
DIVM
CPU clock
divide-by-M
control
DPTR
Data pointer
(2 bytes)
SFR
addr.
Bit functions and addresses
Reset value
MSB
Hex
Binary
95H
00
0000 0000
LSB
83H
00
0000 0000
DPL
Data pointer low
82H
00
0000 0000
FMADRH
Program flash
address high
E7H
00
0000 0000
FMADRL
Program flash
address low
E6H
00
0000 0000
FMCON
Program flash
control (Read)
E4H
70
0111 0000
Program flash
control (Write)
E4H
FMDATA
Program flash
data
E5H
00
0000 0000
I2ADR
I2C-bus slave
address register
DBH
00
0000 0000
I2CON*
I2C-bus
00
x000 00x0
Bit address
control
D8H
-
-
-
HVA
HVE
SV
OI
FMCMD.7 FMCMD.6 FMCMD.5 FMCMD.4 FMCMD.3 FMCMD.2 FMCMD.1 FMCMD.0
I2ADR.6
I2ADR.5
I2ADR.4
I2ADR.3
I2ADR.2
I2ADR.1
I2ADR.0
GC
DF
DE
DD
DC
DB
DA
D9
D8
-
I2EN
STA
STO
SI
AA
-
CRSEL
register
23 of 94
© NXP B.V. 2012. All rights reserved.
I2DAT
I2C-bus data
register
DAH
I2SCLH
Serial clock
generator/SCL
duty cycle
register high
DDH
00
0000 0000
I2SCLL
Serial clock
generator/SCL
duty cycle
register low
DCH
00
0000 0000
I2STAT
I2C-bus status
register
D9H
F8
1111 1000
STA.4
STA.3
STA.2
STA.1
STA.0
0
0
0
P89LPC9331/9341/9351/9361
Data pointer high
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
DPH
BUSY
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 6.
Special function registers - P89LPC9351/9361
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR
addr.
Bit functions and addresses
Reset value
MSB
LSB
Hex
Binary
Input capture A
register high
ABH
00
0000 0000
ICRAL
Input capture A
register low
AAH
00
0000 0000
ICRBH
Input capture B
register high
AFH
00
0000 0000
ICRBL
Input capture B
register low
AEH
00
0000 0000
IEN0*
Interrupt enable 0
00
0000 0000
00[1]
00x0 0000
Bit address
IEN1*
Interrupt enable 1
IP0*
Interrupt priority 0
E8H
Bit address
IP0H
Interrupt priority 0
high
IP1*
Interrupt priority 1
B8H
B7H
Bit address
F8H
AF
AE
AD
AC
AB
AA
A9
A8
EA
EWDRT
EBO
ES/ESR
ET1
EX1
ET0
EX0
EF
EE
ED
EC
EB
EA
E9
E8
EADEE
EST
-
ECCU
ESPI
EC
EKBI
EI2C
BF
BE
BD
BC
BB
BA
B9
B8
-
PWDRT
PBO
PS/PSR
PT1
PX1
PT0
PX0
00[1]
x000 0000
PX0H
00[1]
x000 0000
-
PWDRTH
PBOH
PSH/
PSRH
PT1H
PX1H
PT0H
FF
FE
FD
FC
FB
FA
F9
F8
PADEE
PST
-
PCCU
PSPI
PC
PKBI
PI2C
00[1]
00x0 0000
00x0 0000
24 of 94
© NXP B.V. 2012. All rights reserved.
IP1H
Interrupt priority 1
high
F7H
PAEEH
PSTH
-
PCCUH
PSPIH
PCH
PKBIH
PI2CH
00[1]
KBCON
Keypad control
register
94H
-
-
-
-
-
-
PATN
_SEL
KBIF
00[1]
xxxx xx00
KBMASK
Keypad interrupt
mask register
86H
00
0000 0000
KBPATN
Keypad pattern
register
93H
FF
1111 1111
OCRAH
Output compare
A register high
EFH
00
0000 0000
OCRAL
Output compare
A register low
EEH
00
0000 0000
OCRBH
Output compare
B register high
FBH
00
0000 0000
P89LPC9331/9341/9351/9361
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
A8H
8-bit microcontroller with accelerated two-clock 80C51 core
ICRAH
Bit address
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 6.
Special function registers - P89LPC9351/9361
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR
addr.
Bit functions and addresses
Reset value
MSB
LSB
Hex
Binary
Output compare
B register low
FAH
00
0000 0000
OCRCH
Output compare
C register high
FDH
00
0000 0000
OCRCL
Output compare
C register low
FCH
00
0000 0000
OCRDH
Output compare
D register high
FFH
00
0000 0000
OCRDL
Output compare
D register low
FEH
00
0000 0000
P0*
Port 0
80H
P1*
Port 1
90H
Bit address
P2*
Port 2
A0H
Bit address
86
85
84
83
82
81
80
T1/KB7
CMP1
/KB6
CMPREF
/KB5
CIN1A
/KB4
CIN1B
/KB3
CIN2A
/KB2
CIN2B
/KB1
CMP2
/KB0
97
96
95
94
93
92
91
90
OCC
OCB
RST
INT1
INT0/SDA
T0/SCL
RXD
TXD
A7
A6
A5
A4
A3
A2
A1
A0
ICA
OCA
SPICLK
SS
MISO
MOSI
OCD
ICB
B7
B6
B5
B4
B3
B2
B1
B0
[1]
[1]
[1]
[1]
25 of 94
© NXP B.V. 2012. All rights reserved.
P3*
Port 3
B0H
-
-
-
-
-
-
XTAL1
XTAL2
P0M1
Port 0 output
mode 1
84H
(P0M1.7)
(P0M1.6)
(P0M1.5)
(P0M1.4)
(P0M1.3)
(P0M1.2)
(P0M1.1)
(P0M1.0)
FF[1]
1111 1111
P0M2
Port 0 output
mode 2
85H
(P0M2.7)
(P0M2.6)
(P0M2.5)
(P0M2.4)
(P0M2.3)
(P0M2.2)
(P0M2.1)
(P0M2.0)
00[1]
0000 0000
P1M1
Port 1 output
mode 1
91H
(P1M1.7)
(P1M1.6)
-
(P1M1.4)
(P1M1.3)
(P1M1.2)
(P1M1.1)
(P1M1.0)
D3[1]
11x1 xx11
P1M2
Port 1 output
mode 2
92H
(P1M2.7)
(P1M2.6)
-
(P1M2.4)
(P1M2.3)
(P1M2.2)
(P1M2.1)
(P1M2.0)
00[1]
00x0 xx00
P2M1
Port 2 output
mode 1
A4H
(P2M1.7)
(P2M1.6)
(P2M1.5)
(P2M1.4)
(P2M1.3)
(P2M1.2)
(P2M1.1)
(P2M1.0)
FF[1]
1111 1111
P2M2
Port 2 output
mode 2
A5H
(P2M2.7)
(P2M2.6)
(P2M2.5)
(P2M2.4)
(P2M2.3)
(P2M2.2)
(P2M2.1)
(P2M2.0)
00[1]
0000 0000
P89LPC9331/9341/9351/9361
Bit address
87
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
OCRBL
Bit address
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 6.
Special function registers - P89LPC9351/9361
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR
addr.
Bit functions and addresses
Reset value
MSB
LSB
Hex
Binary
xxxx xx11
B1H
-
-
-
-
-
-
(P3M1.1)
(P3M1.0)
P3M2
Port 3 output
mode 2
B2H
-
-
-
-
-
-
(P3M2.1)
(P3M2.0)
00[1]
xxxx xx00
PCON
Power control
register
87H
SMOD1
SMOD0
-
BOI
GF1
GF0
PMOD1
PMOD0
00
0000 0000
PCONA
Power control
register A
B5H
RTCPD
DEEPD
VCPD
ADPD
I2PD
SPPD
SPD
CCUPD
00[1]
0000 0000
D7
D6
D5
D4
D3
D2
D1
D0
PSW*
Program status
word
D0H
CY
AC
F0
RS1
RS0
OV
F1
P
00
0000 0000
PT0AD
Port 0 digital input
disable
F6H
-
-
PT0AD.5
PT0AD.4
PT0AD.3
PT0AD.2
PT0AD.1
-
00
xx00 000x
RSTSRC
Reset source
register
DFH
-
BOIF
BOF
POF
R_BK
R_WD
R_SF
R_EX
[3]
RTCCON
RTC control
D1H
RTCF
RTCS1
RTCS0
-
-
-
ERTC
RTCEN
RTCH
RTC register high
D2H
00[6]
0000 0000
RTCL
RTC register low
D3H
00[6]
0000 0000
SADDR
Serial port
address register
A9H
00
0000 0000
SADEN
Serial port
address enable
B9H
00
0000 0000
SBUF
Serial Port data
buffer register
99H
xx
xxxx xxxx
9F
9E
9D
9C
9B
9A
99
98
SCON*
Serial port control
98H
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
00
0000 0000
SSTAT
Serial port
extended status
register
BAH
DBMOD
INTLO
CIDIS
DBISEL
FE
BR
OE
STINT
00
0000 0000
SP
Stack pointer
81H
07
0000 0111
SPCTL
SPI control
register
E2H
04
0000 0100
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
Bit address
26 of 94
© NXP B.V. 2012. All rights reserved.
SSIG
SPEN
DORD
MSTR
CPOL
CPHA
SPR1
SPR0
60[1][6] 011x xx00
P89LPC9331/9341/9351/9361
Port 3 output
mode 1
8-bit microcontroller with accelerated two-clock 80C51 core
P3M1
03[1]
Bit address
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 6.
Special function registers - P89LPC9351/9361
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR
addr.
SPSTAT
SPI status
register
E1H
SPDAT
SPI data register
E3H
TAMOD
Timer 0 and 1
auxiliary mode
8FH
Bit address
Bit functions and addresses
Reset value
MSB
SPIF
LSB
WCOL
-
-
-
-
-
-
-
-
-
T1M2
-
-
-
T0M2
8F
8E
8D
8C
8B
8A
89
88
Hex
Binary
00
00xx xxxx
00
0000 0000
00
xxx0 xxx0
88H
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
00
0000 0000
TCR20*
CCU control
register 0
C8H
PLEEN
HLTRN
HLTEN
ALTCD
ALTAB
TDIR2
TMOD21
TMOD20
00
0000 0000
TCR21
CCU control
register 1
F9H
TCOU2
-
-
-
PLLDV.3
PLLDV.2
PLLDV.1
PLLDV.0
00
0xxx 0000
TH0
Timer 0 high
8CH
00
0000 0000
TH1
Timer 1 high
8DH
00
0000 0000
TH2
CCU timer high
CDH
00
0000 0000
TICR2
CCU interrupt
control register
C9H
TOIE2
TOCIE2D
TOCIE2C
TOCIE2B
TOCIE2A
-
TICIE2B
TICIE2A
00
0000 0x00
TIFR2
CCU interrupt flag
register
E9H
TOIF2
TOCF2D
TOCF2C
TOCF2B
TOCF2A
-
TICF2B
TICF2A
00
0000 0x00
TISE2
CCU interrupt
status encode
register
DEH
-
-
-
-
-
ENCINT.2
ENCINT.1
ENCINT.0 00
xxxx x000
TL0
Timer 0 low
8AH
00
0000 0000
TL1
Timer 1 low
8BH
00
0000 0000
TL2
CCU timer low
CCH
TMOD
Timer 0 and 1
mode
89H
TOR2H
CCU reload
register high
TOR2L
TPCR2H
00
0000 0000
00
0000 0000
CFH
00
0000 0000
CCU reload
register low
CEH
00
0000 0000
Prescaler control
register high
CBH
-
T1C/T
-
T1M1
-
T1M0
-
T0GATE
-
T0C/T
-
T0M1
T0M0
TPCR2H.1 TPCR2H.0 00
xxxx xx00
P89LPC9331/9341/9351/9361
27 of 94
© NXP B.V. 2012. All rights reserved.
Timer 0 and 1
control
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
TCON*
T1GATE
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 6.
Special function registers - P89LPC9351/9361
* indicates SFRs that are bit addressable.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Name
Description
SFR
addr.
Bit functions and addresses
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 6.
Special function registers - P89LPC9351/9361
* indicates SFRs that are bit addressable.
Reset value
MSB
LSB
Hex
Prescaler control
register low
CAH
TPCR2L.7 TPCR2L.6 TPCR2L.5 TPCR2L.4 TPCR2L.3 TPCR2L.2 TPCR2L.1 TPCR2L.0 00
TRIM
Internal oscillator
trim register
96H
RCCLK
ENCLK
TRIM.5
TRIM.4
TRIM.3
TRIM.2
TRIM.1
TRIM.0
[5][6]
WDCON
Watchdog control
register
A7H
PRE2
PRE1
PRE0
-
-
WDRUN
WDTOF
WDCLK
[4][6]
WDL
Watchdog load
C1H
WFEED1
Watchdog feed 1
C2H
WFEED2
Watchdog feed 2
C3H
FF
0000 0000
1111 1111
All ports are in input only (high-impedance) state after power-up.
[2]
BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable.
[3]
The RSTSRC register reflects the cause of the P89LPC9351/9361 reset except BOIF bit. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the
power-on reset value is x011 0000.
[4]
After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset.
Other resets will not affect WDTOF.
[5]
On power-on reset and watchdog reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register.
[6]
The only reset sources that affect these SFRs are power-on reset and watchdog reset.
28 of 94
© NXP B.V. 2012. All rights reserved.
P89LPC9331/9341/9351/9361
[1]
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
TPCR2L
Binary
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Extended special function registers - P89LPC9351/9361[1]
Name
Description
SFR
addr.
BODCFG
BOD
configuration
register
FFC8H
-
-
-
-
-
-
BOICFG1
BOICFG0
[2]
CLKCON
CLOCK
Control
register
FFDEH
CLKOK
-
-
XTALWD
CLKDBL
FOSC2
FOSC1
FOSC0
[3]
1000 xxxx
PGACON1
PGA1 control
register
FFE1H
ENPGA1
PGATRIM
1
-
-
PGAG11
PGAG10
00
0000 0000
PGACON1B
PGA1 control
register B
FFE4H
-
-
-
-
-
PGAENO 00
FF1
0000 0000
Bit functions and addresses
Reset value
MSB
LSB
PGASEL1 PGASEL1
1
0
-
-
Hex Binary
16XTRIM3 16XTRIM2 16XTRIM1 16XTRIM0
8XTRIM3
8XTRIM2
8XTRIM1
8XTRIM0
[4]
PGA1TRIM2X4X
PGA1 trim
register
FFE2H
4XTRIM3
4XTRIM2
4XTRIM1
4XTRIM0
2XTRIM3
2XTRIM2
2XTRIM1
2XTRIM0
[4]
PGACON0
PGA0 control
register
FFCAH
ENPGA0
PGASEL0 PGASEL0
1
0
PGATRIM
0
TSEL1
TSEL0
PGAG01
PGAG00
00
0000 0000
PGACON0B
PGA0 control
register B
FFCEH
-
-
-
-
-
PGAENO 00
FF0
0000 0000
-
-
PGA0TRIM8X16X PGA0 trim
register
FFCDH 16XTRIM3 16XTRIM2 16XTRIM1 16XTRIM0
8XTRIM3
8XTRIM2
8XTRIM1
8XTRIM0
[4]
PGA0TRIM2X4X
PGA0 trim
register
FFCCH
2XTRIM3
2XTRIM2
2XTRIM1
2XTRIM0
[4]
RTCDATH
Real-time
clock data
register high
FFBFH
00
0000 0000
RTCDATL
Real-time
clock data
register low
FFBEH
00
0000 0000
4XTRIM3
4XTRIM2
4XTRIM1
4XTRIM0
29 of 94
© NXP B.V. 2012. All rights reserved.
Extended SFRs are physically located on-chip but logically located in external data memory address space (XDATA). The MOVX A,@DPTR and MOVX @DPTR,A instructions are
used to access these extended SFRs.
[2]
The BOICFG1/0 will be copied from UCFG1.5 and UCFG1.3 when power-on reset.
[3]
CLKCON register reset value comes from UCFG1 and UCFG2. The reset value of CLKCON.2 to CLKCON.0 come from UCFG1.2 to UCFG1.0 and reset value of CLKDBL bit
comes from UCFG2.7.
[4]
On power-on reset and watchdog reset, the PGAxTRIM8X16X and PGAxTRIM2X4X registers are initialized with a factory preprogrammed value. Other resets will not cause
initialization.
P89LPC9331/9341/9351/9361
FFE3H
8-bit microcontroller with accelerated two-clock 80C51 core
Rev. 5.1 — 20 August 2012
All information provided in this document is subject to legal disclaimers.
PGA1TRIM8X16X PGA1 trim
register
[1]
NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Table 7.
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.2 Enhanced CPU
The P89LPC9331/9341/9351/9361 uses an enhanced 80C51 CPU which runs at
six times the speed of standard 80C51 devices. A machine cycle consists of two CPU
clock cycles, and most instructions execute in one or two machine cycles.
7.3 Clocks
7.3.1 Clock definitions
The P89LPC9331/9341/9351/9361 device has several internal clocks as defined below:
OSCCLK — Input to the DIVM clock divider. OSCCLK is selected from one of four clock
sources (see Figure 7) and can also be optionally divided to a slower frequency (see
Section 7.11 “CCLK modification: DIVM register”).
Remark: fosc is defined as the OSCCLK frequency.
CCLK — CPU clock; output of the clock divider. There are two CCLK cycles per machine
cycle, and most instructions are executed in one to two machine cycles (two or four CCLK
cycles).
RCCLK — The internal 7.373 MHz RC oscillator output. The clock doubler option, when
enabled, provides an output frequency of 14.746 MHz.
PCLK — Clock for the various peripheral devices and is CCLK⁄2.
7.3.2 CPU clock (OSCCLK)
The P89LPC9331/9341/9351/9361 provides several user-selectable oscillator options in
generating the CPU clock. This allows optimization for a range of needs from high
precision to lowest possible cost. These options are configured when the flash is
programmed and include an on-chip watchdog oscillator, an on-chip RC oscillator, an
oscillator using an external crystal, or an external clock source.
7.4 Crystal oscillator option
The crystal oscillator option can be optimized for low, medium, or high frequency crystals
covering a range from 20 kHz to 18 MHz. It can be the clock source of OSCCLK, and
RTC. Low speed oscillator option can be the clock source of WDT.
7.4.1 Low speed oscillator option
This option supports an external crystal in the range of 20 kHz to 100 kHz. Ceramic
resonators are also supported in this configuration.
7.4.2 Medium speed oscillator option
This option supports an external crystal in the range of 100 kHz to 4 MHz. Ceramic
resonators are also supported in this configuration.
7.4.3 High speed oscillator option
This option supports an external crystal in the range of 4 MHz to 18 MHz. Ceramic
resonators are also supported in this configuration.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
30 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.5 Clock output
The P89LPC9331/9341/9351/9361 supports a user-selectable clock output function on
the XTAL2/CLKOUT pin when crystal oscillator is not being used. This condition occurs if
another clock source has been selected (on-chip RC oscillator, watchdog oscillator,
external clock input on XTAL1) and if the RTC and WDT are not using the crystal oscillator
as their clock source. This allows external devices to synchronize to the
P89LPC9331/9341/9351/9361. This output is enabled by the ENCLK bit in the TRIM
register.
The frequency of this clock output is 1⁄2 that of the CCLK. If the clock output is not needed
in Idle mode, it may be turned off prior to entering Idle, saving additional power.
7.6 On-chip RC oscillator option
The P89LPC9331/9341/9351/9361 has a 6-bit TRIM register that can be used to tune the
frequency of the RC oscillator. During reset, the TRIM value is initialized to a factory
preprogrammed value to adjust the oscillator frequency to 7.373 MHz 1 % at room
temperature. End-user applications can write to the TRIM register to adjust the on-chip
RC oscillator to other frequencies. When the clock doubler option is enabled (UCFG2.7 =
1), the output frequency is 14.746 MHz. If CCLK is 8 MHz or slower, the CLKLP SFR bit
(AUXR1.7) can be set to logic 1 to reduce power consumption. On reset, CLKLP is logic 0
allowing highest performance access. This bit can then be set in software if CCLK is
running at 8 MHz or slower. When clock doubler option is enabled, BOE1 bit (UCFG1.5)
and BOE0 bit (UCFG1.3) are required to hold the device in reset at power-up until VDD
has reached its specified level.
7.7 Watchdog oscillator option
The watchdog has a separate oscillator which has a frequency of 400 kHz, calibrated to
5 % at room temperature. This oscillator can be used to save power when a high clock
frequency is not needed.
7.8 External clock input option
In this configuration, the processor clock is derived from an external source driving the
P3.1/XTAL1 pin. The rate may be from 0 Hz up to 18 MHz. The P3.0/XTAL2 pin may be
used as a standard port pin or a clock output. When using an oscillator frequency above
12 MHz, BOE1 bit (UCFG1.5) and BOE0 bit (UCFG1.3) are required to hold the device in
reset at power-up until VDD has reached its specified level.
7.9 Clock source switching on the fly
P89LPC9331/9341/9351/9361 can implement clock switching on any sources of
watchdog oscillator, 7 MHz/14 MHz internal RC oscillator, crystal oscillator and external
clock input during code is running. CLKOK bit in CLKCON register is used to indicate the
clock switch status. CLKOK is cleared when starting clock source switch and set when
completed. Notice that when CLKOK is ‘0’, writing to CLKCON register is not allowed.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
31 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
XTAL1
XTAL2
HIGH FREQUENCY
MEDIUM FREQUENCY
LOW FREQUENCY
RTC
ADC1
ADC0
OSCCLK
RC OSCILLATOR
WITH CLOCK DOUBLER
DIVM
RCCLK
CCLK
CPU
÷2
PCLK
(7.3728 MHz/14.7456 MHz ± 1 %)
WDT
WATCHDOG
OSCILLATOR
PCLK
(400 kHz ± 5 %)
32 × PLL
CCU
TIMER 0 AND
TIMER 1
I2C-BUS
SPI
UART
(P89LPC9351/9361)
002aad559
Fig 7.
Block diagram of oscillator control
7.10 CCLK wake-up delay
The P89LPC9331/9341/9351/9361 has an internal wake-up timer that delays the clock
until it stabilizes depending on the clock source used. If the clock source is any of the
three crystal selections (low, medium and high frequencies) the delay is 1024 OSCCLK
cycles plus 60 s to 100 s. If the clock source is the internal RC oscillator, the delay is
200 s to 300 s. If the clock source is watchdog oscillator or external clock, the delay is
32 OSCCLK cycles.
7.11 CCLK modification: DIVM register
The OSCCLK frequency can be divided down up to 510 times by configuring a dividing
register, DIVM, to generate CCLK. This feature makes it possible to temporarily run the
CPU at a lower rate, reducing power consumption. By dividing the clock, the CPU can
retain the ability to respond to events that would not exit Idle mode by executing its normal
program at a lower rate. This can also allow bypassing the oscillator start-up time in cases
where Power-down mode would otherwise be used. The value of DIVM may be changed
by the program at any time without interrupting code execution.
7.12 Low power select
The P89LPC9331/9341/9351/9361 is designed to run at 18 MHz (CCLK) maximum.
However, if CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to logic 1
to lower the power consumption further. On any reset, CLKLP is logic 0 allowing highest
performance access. This bit can then be set in software if CCLK is running at 8 MHz or
slower.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
32 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.13 Memory organization
The various P89LPC9331/9341/9351/9361 memory spaces are as follows:
• DATA
128 bytes of internal data memory space (00H:7FH) accessed via direct or indirect
addressing, using instructions other than MOVX and MOVC. All or part of the Stack
may be in this area.
• IDATA
Indirect Data. 256 bytes of internal data memory space (00H:FFH) accessed via
indirect addressing using instructions other than MOVX and MOVC. All or part of the
Stack may be in this area. This area includes the DATA area and the 128 bytes
immediately above it.
• SFR
Special Function Registers. Selected CPU registers and peripheral control and status
registers, accessible only via direct addressing.
• XDATA (P89LPC9351/9361)
‘External’ Data or Auxiliary RAM. Duplicates the classic 80C51 64 kB memory space
addressed via the MOVX instruction using the DPTR, R0, or R1. All or part of this
space could be implemented on-chip. The P89LPC9351/9361 has 512 bytes of
on-chip XDATA memory, plus extended SFRs located in XDATA.
• CODE
64 kB of Code memory space, accessed as part of program execution and via the
MOVC instruction. The P89LPC9331/9341/9351/9361 has 4 kB/8 kB/16 kB of on-chip
Code memory.
The P89LPC9351/9361 also has 512 bytes of on-chip data EEPROM that is accessed via
SFRs (see Section 7.14).
7.14 Data RAM arrangement
The 768 bytes of on-chip RAM are organized as shown in Table 8.
Table 8.
On-chip data memory usages
Type
Data RAM
Size (bytes)
DATA
Memory that can be addressed directly and indirectly
128
IDATA
Memory that can be addressed indirectly
256
XDATA
Auxiliary (External Data) on-chip memory that is accessed
using the MOVX instructions (P89LPC9351/9361)
512
7.15 Interrupts
The P89LPC9331/9341/9351/9361 uses a four priority level interrupt structure. This
allows great flexibility in controlling the handling of the many interrupt sources. The
P89LPC9331/9341/9351/9361 supports 15 interrupt sources: external interrupts 0 and 1,
timers 0 and 1, serial port TX, serial port RX, combined serial port RX/TX, brownout
detect, watchdog/RTC, I2C-bus, keyboard, comparators 1 and 2, SPI, CCU, data
EEPROM write/ADC completion.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
33 of 94
NXP Semiconductors
P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core
Each interrupt source can be individually enabled or disabled by setting or clearing a bit in
the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a global
disable bit, EA, which disables all interrupts.
Each interrupt source can be individually programmed to one of four priority levels by
setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1 and IP1H. An
interrupt service routine in progress can be interrupted by a higher priority interrupt, but
not by another interrupt of the same or lower priority. The highest priority interrupt service
cannot be interrupted by any other interrupt source. If two requests of different priority
levels are pending at the start of an instruction, the request of higher priority level is
serviced.
If requests of the same priority level are pending at the start of an instruction, an internal
polling sequence determines which request is serviced. This is called the arbitration
ranking. Note that the arbitration ranking is only used to resolve pending requests of the
same priority level.
7.15.1 External interrupt inputs
The P89LPC9331/9341/9351/9361 has two external interrupt inputs as well as the
Keypad Interrupt function. The two interrupt inputs are identical to those present on the
standard 80C51 microcontrollers.
These external interrupts can be programmed to be level-triggered or edge-triggered by
setting or clearing bit IT1 or IT0 in Register TCON.
In edge-triggered mode, if successive samples of the INTn pin show a HIGH in one cycle
and a LOW in the next cycle, the interrupt request flag IEn in TCON is set, causing an
interrupt request.
If an external interrupt is enabled when the P89LPC9331/9341/9351/9361 is put into
Power-down or Idle mode, the interrupt will cause the processor to wake-up and resume
operation. Refer to Section 7.18 “Power reduction modes” for details.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
34 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
IE0
EX0
IE1
EX1
BOIF
EBO
RTCF
ERTC
(RTCCON.1)
WDOVF
wake-up
(if in power-down)
KBIF
EKBI
EWDRT
CMF2
CMF1
EC
EA (IE0.7)
TF0
ET0
TF1
ET1
TI & RI/RI
ES/ESR
TI
EST
interrupt
to CPU
SI
EI2C
SPIF
ESPI
any CCU interrupt(1)
ECCU
EEIF(2)
ENADCI0
ADCI0
ENADCI1
ADCI1
ENBI0
BNDI0
ENBI1
BNDI1
EADEE(2)
EAD(3)
002aad560
(1) See Section 7.22 “CCU (P89LPC9351/9361)”.
(2) P89LPC9351/9361
(3) P89LPC9331/9341
Fig 8.
Interrupt sources, interrupt enables, and power-down wake-up sources
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
35 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.16 I/O ports
The P89LPC9331/9341/9351/9361 has four I/O ports: Port 0, Port 1, Port 2 and Port 3.
Ports 0, 1, and 2 are 8-bit ports, and Port 3 is a 2-bit port. The exact number of I/O pins
available depends upon the clock and reset options chosen, as shown in Table 9.
Table 9.
Number of I/O pins available
Clock source
Reset option
Number of I/O
pins (28-pin
package)
On-chip oscillator or watchdog
oscillator
No external reset (except during
power-up)
26
External RST pin supported
25
External clock input
No external reset (except during
power-up)
25
External RST pin supported
24
No external reset (except during
power-up)
24
External RST pin supported
23
Low/medium/high speed
oscillator (external crystal or
resonator)
7.16.1 Port configurations
All but three I/O port pins on the P89LPC9331/9341/9351/9361 may be configured by
software to one of four types on a bit-by-bit basis. These are: quasi-bidirectional (standard
80C51 port outputs), push-pull, open drain, and input-only. Two configuration registers for
each port select the output type for each port pin.
1. P1.5 (RST) can only be an input and cannot be configured.
2. P1.2 (SCL/T0) and P1.3 (SDA/INT0) may only be configured to be either input-only or
open-drain.
7.16.1.1
Quasi-bidirectional output configuration
Quasi-bidirectional output type can be used as both an input and output without the need
to reconfigure the port. This is possible because when the port outputs a logic HIGH, it is
weakly driven, allowing an external device to pull the pin LOW. When the pin is driven
LOW, it is driven strongly and able to sink a fairly large current. These features are
somewhat similar to an open-drain output except that there are three pull-up transistors in
the quasi-bidirectional output that serve different purposes.
The P89LPC9331/9341/9351/9361 is a 3 V device, but the pins are 5 V-tolerant. In
quasi-bidirectional mode, if a user applies 5 V on the pin, there will be a current flowing
from the pin to VDD, causing extra power consumption. Therefore, applying 5 V in
quasi-bidirectional mode is discouraged.
A quasi-bidirectional port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
7.16.1.2
Open-drain output configuration
The open-drain output configuration turns off all pull-ups and only drives the pull-down
transistor of the port driver when the port latch contains a logic 0. To be used as a logic
output, a port configured in this manner must have an external pull-up, typically a resistor
tied to VDD.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
36 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
An open-drain port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
7.16.1.3
Input-only configuration
The input-only port configuration has no output drivers. It is a Schmitt trigger input that
also has a glitch suppression circuit.
7.16.1.4
Push-pull output configuration
The push-pull output configuration has the same pull-down structure as both the
open-drain and the quasi-bidirectional output modes, but provides a continuous strong
pull-up when the port latch contains a logic 1. The push-pull mode may be used when
more source current is needed from a port output. A push-pull port pin has a
Schmitt triggered input that also has a glitch suppression circuit. The
P89LPC9331/9341/9351/9361 device has high current source on eight pins in push-pull
mode. See Table 11 “Limiting values”.
7.16.2 Port 0 analog functions
The P89LPC9331/9341/9351/9361 incorporates two Analog Comparators. In order to give
the best analog function performance and to minimize power consumption, pins that are
being used for analog functions must have the digital outputs and digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input-Only
(high-impedance) mode.
Digital inputs on Port 0 may be disabled through the use of the PT0AD register, bits 1:5.
On any reset, PT0AD[1:5] defaults to logic 0s to enable digital functions.
7.16.3 Additional port features
After power-up, all pins are in Input-Only mode. Please note that this is different from
the LPC76x series of devices.
• After power-up, all I/O pins except P1.5, may be configured by software.
• Pin P1.5 is input only. Pins P1.2 and P1.3 are configurable for either input-only or
open-drain.
Every output on the P89LPC9331/9341/9351/9361 has been designed to sink typical LED
drive current. However, there is a maximum total output current for all ports which must
not be exceeded. Please refer to Table 12 “Static characteristics” for detailed
specifications.
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
7.17 Power monitoring functions
The P89LPC9331/9341/9351/9361 incorporates power monitoring functions designed to
prevent incorrect operation during initial power-up and power loss or reduction during
operation. This is accomplished with two hardware functions: Power-on detect and
brownout detect.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
37 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.17.1 Brownout detection
The brownout detect function determines if the power supply voltage drops below a
certain level. Enhanced brownout detection has 3 independent functions: BOD reset,
BOD interrupt and BOD EEPROM/FLASH.
BOD reset is always on except in total Power-down mode. It could not be disabled in
software. BOD interrupt may be enabled or disabled in software. BOD EEPROM/FLASH
is always on, except in Power-down modes and could not be disabled in software.
BOD reset and BOD interrupt, each has four trip voltage levels. BOE1 bit (UCFG1.5) and
BOE0 bit (UCFG1.3) are used as trip point configuration bits of BOD reset. BOICFG1 bit
and BOICFG0 bit in register BODCFG are used as trip point configuration bits of BOD
interrupt. BOD reset voltage should be lower than BOD interrupt trip point. BOD
EEPROM/FLASH is used for flash/Data EEPROM programming/erase protection and has
only 1 trip voltage of 2.4 V. Please refer to P89LPC9331/9341/9351/9361 User manual for
detail configurations.
If brownout detection is enabled the brownout condition occurs when VDD falls below the
brownout trip voltage and is negated when VDD rises above the brownout trip voltage.
For correct activation of brownout detect, the VDD rise and fall times must be observed.
Please see Table 12 “Static characteristics” for specifications.
7.17.2 Power-on detection
The Power-on detect has a function similar to the brownout detect, but is designed to work
as power comes up initially, before the power supply voltage reaches a level where
brownout detect can work. The POF flag in the RSTSRC register is set to indicate an
initial power-up condition. The POF flag will remain set until cleared by software.
7.18 Power reduction modes
The P89LPC9331/9341/9351/9361 supports three different power reduction modes.
These modes are Idle mode, Power-down mode, and total Power-down mode.
7.18.1 Idle mode
Idle mode leaves peripherals running in order to allow them to activate the processor
when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle
mode.
7.18.2 Power-down mode
The Power-down mode stops the oscillator in order to minimize power consumption. The
P89LPC9331/9341/9351/9361 exits Power-down mode via any reset, or certain interrupts.
In Power-down mode, the power supply voltage may be reduced to the data retention
supply voltage VDDR. This retains the RAM contents at the point where Power-down mode
was entered. SFR contents are not guaranteed after VDD has been lowered to VDDR,
therefore it is highly recommended to wake-up the processor via reset in this case. VDD
must be raised to within the operating range before the Power-down mode is exited.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
38 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Some chip functions continue to operate and draw power during Power-down mode,
increasing the total power used during power-down. These include: Brownout detect,
watchdog timer, comparators (note that comparators can be powered down separately),
and RTC/system timer. The internal RC oscillator is disabled unless both the RC oscillator
has been selected as the system clock and the RTC is enabled.
7.18.3 Total Power-down mode
This is the same as Power-down mode except that the brownout detection circuitry and
the voltage comparators are also disabled to conserve additional power. The internal RC
oscillator is disabled unless both the RC oscillator has been selected as the system clock
and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during
power-down, there will be high power consumption. Please use an external low frequency
clock to achieve low power with the RTC running during power-down.
7.19 Reset
The P1.5/RST pin can function as either a LOW-active reset input or as a digital input,
P1.5. The Reset Pin Enable (RPE) bit in UCFG1, when set to logic 1, enables the external
reset input function on P1.5. When cleared, P1.5 may be used as an input pin.
Remark: During a power-up sequence, the RPE selection is overridden and this pin
always functions as a reset input. An external circuit connected to this pin should not
hold this pin LOW during a power-on sequence as this will keep the device in reset.
After power-up this pin will function as defined by the RPE bit. Only a power-up reset will
temporarily override the selection defined by RPE bit. Other sources of reset will not
override the RPE bit. When this pin functions as a reset input, an internal pull-up
resistance is connected (see Table 12 “Static characteristics”).
Note: During a power cycle, VDD must fall below VPOR before power is reapplied, in order
to ensure a power-on reset (see Table 12 “Static characteristics”).
Reset can be triggered from the following sources:
•
•
•
•
•
•
External reset pin (during power-up or if user configured via UCFG1)
Power-on detect
Brownout detect
Watchdog timer
Software reset
UART break character detect reset
For every reset source, there is a flag in the Reset Register, RSTSRC. The user can read
this register to determine the most recent reset source. These flag bits can be cleared in
software by writing a logic 0 to the corresponding bit. More than one flag bit may be set:
• During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
• A Watchdog reset is similar to a power-on reset, both POF and BOF are set but the
other flag bits are cleared.
• For any other reset, previously set flag bits that have not been cleared will remain set.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
39 of 94
NXP Semiconductors
P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core
7.19.1 Reset vector
Following reset, the P89LPC9331/9341/9351/9361 will fetch instructions from either
address 0000H or the Boot address. The Boot address is formed by using the boot vector
as the high byte of the address and the low byte of the address = 00H.
The boot address will be used if a UART break reset occurs, or the non-volatile boot
status bit (BOOTSTAT.0) = 1, or the device is forced into ISP mode during power-on (see
P89LPC9331/9341/9351/9361 User manual). Otherwise, instructions will be fetched from
address 0000H.
7.20 Timers/counters 0 and 1
The P89LPC9331/9341/9351/9361 has two general purpose counter/timers which are
upward compatible with the standard 80C51 Timer 0 and Timer 1. Both can be configured
to operate either as timers or event counters. An option to automatically toggle the T0
and/or T1 pins upon timer overflow has been added.
In the ‘Timer’ function, the register is incremented every machine cycle.
In the ‘Counter’ function, the register is incremented in response to a 1-to-0 transition at its
corresponding external input pin, T0 or T1. In this function, the external input is sampled
once during every machine cycle.
Timer 0 and Timer 1 have five operating modes (Modes 0, 1, 2, 3 and 6). Modes 0, 1, 2
and 6 are the same for both Timers/Counters. Mode 3 is different.
7.20.1 Mode 0
Putting either Timer into Mode 0 makes it look like an 8048 Timer, which is an 8-bit
Counter with a divide-by-32 prescaler. In this mode, the Timer register is configured as a
13-bit register. Mode 0 operation is the same for Timer 0 and Timer 1.
7.20.2 Mode 1
Mode 1 is the same as Mode 0, except that all 16 bits of the timer register are used.
7.20.3 Mode 2
Mode 2 configures the Timer register as an 8-bit Counter with automatic reload. Mode 2
operation is the same for Timer 0 and Timer 1.
7.20.4 Mode 3
When Timer 1 is in Mode 3 it is stopped. Timer 0 in Mode 3 forms two separate 8-bit
counters and is provided for applications that require an extra 8-bit timer. When Timer 1 is
in Mode 3 it can still be used by the serial port as a baud rate generator.
7.20.5 Mode 6
In this mode, the corresponding timer can be changed to a PWM with a full period of
256 timer clocks.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
40 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.20.6 Timer overflow toggle output
Timers 0 and 1 can be configured to automatically toggle a port output whenever a timer
overflow occurs. The same device pins that are used for the T0 and T1 count inputs are
also used for the timer toggle outputs. The port outputs will be a logic 1 prior to the first
timer overflow when this mode is turned on.
7.21 RTC/system timer
The P89LPC9331/9341/9351/9361 has a simple RTC that allows a user to continue
running an accurate timer while the rest of the device is powered down. The RTC can be
a wake-up or an interrupt source. The RTC is a 23-bit down counter comprised of a 7-bit
prescaler and a 16-bit loadable down counter. When it reaches all logic 0s, the counter will
be reloaded again and the RTCF flag will be set. The clock source for this counter can be
either the CPU clock (CCLK) or the XTAL oscillator. Only power-on reset and watchdog
reset will reset the RTC and its associated SFRs to the default state.
The 16-bit loadable counter portion of the RTC is readable by reading the RTCDATL and
RTCDATH registers.
7.22 CCU (P89LPC9351/9361)
This unit features:
• A 16-bit timer with 16-bit reload on overflow.
• Selectable clock, with prescaler to divide clock source by any integral number
between 1 and 1024.
•
•
•
•
Four compare/PWM outputs with selectable polarity
Symmetrical/asymmetrical PWM selection
Two capture inputs with event counter and digital noise rejection filter
Seven interrupts with common interrupt vector (one overflow, two capture, four
compare)
• Safe 16-bit read/write via shadow registers.
7.22.1 CCU clock
The CCU runs on the CCUCLK, which is either PCLK in basic timer mode, or the output of
a PLL. The PLL is designed to use a clock source between 0.5 MHz to 1 MHz that is
multiplied by 32 to produce a CCUCLK between 16 MHz and 32 MHz in PWM mode
(asymmetrical or symmetrical). The PLL contains a 4-bit divider to help divide PCLK into a
frequency between 0.5 MHz and 1 MHz.
7.22.2 CCUCLK prescaling
This CCUCLK can further be divided down by a prescaler. The prescaler is implemented
as a 10-bit free-running counter with programmable reload at overflow.
7.22.3 Basic timer operation
The timer is a free-running up/down counter with a direction control bit. If the timer
counting direction is changed while the counter is running, the count sequence will be
reversed. The timer can be written or read at any time.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
41 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
When a reload occurs, the CCU Timer Overflow Interrupt Flag will be set, and an interrupt
generated if enabled. The 16-bit CCU timer may also be used as an 8-bit up/down timer.
7.22.4 Output compare
There are four output compare channels: A, B, C and D. Each output compare channel
needs to be enabled in order to operate and the user will have to set the associated I/O
pin to the desired output mode to connect the pin. When the contents of the timer matches
that of a capture compare control register, the Timer Output Compare Interrupt Flag
(TOCFx) becomes set. An interrupt will occur if enabled.
7.22.5 Input capture
Input capture is always enabled. Each time a capture event occurs on one of the two input
capture pins, the contents of the timer is transferred to the corresponding 16-bit input
capture register. The capture event can be programmed to be either rising or falling edge
triggered. A simple noise filter can be enabled on the input capture by enabling the Input
Capture Noise Filter bit. If set, the capture logic needs to see four consecutive samples of
the same value in order to recognize an edge as a capture event. An event counter can be
set to delay a capture by a number of capture events.
7.22.6 PWM operation
PWM operation has two main modes, symmetrical and asymmetrical.
In asymmetrical PWM operation the CCU timer operates in down-counting mode
regardless of the direction control bit.
In symmetrical mode, the timer counts up/down alternately. The main difference from
basic timer operation is the operation of the compare module, which in PWM mode is
used for PWM waveform generation.
As with basic timer operation, when the PWM (compare) pins are connected to the
compare logic, their logic state remains unchanged. However, since bit FCO is used to
hold the halt value, only a compare event can change the state of the pin.
TOR2
compare value
timer value
0x0000
non-inverted
inverted
002aaa893
Fig 9.
Asymmetrical PWM, down-counting
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
42 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
TOR2
compare value
timer value
0
non-inverted
inverted
002aaa894
Fig 10. Symmetrical PWM
7.22.7 Alternating output mode
In asymmetrical mode, the user can set up PWM channels A/B and C/D as alternating
pairs for bridge drive control. In this mode the output of these PWM channels are
alternately gated on every counter cycle.
TOR2
COMPARE VALUE A (or C)
COMPARE VALUE B (or D)
TIMER VALUE
0
PWM OUTPUT (OCA or OCC)
PWM OUTPUT (OCB or OCD)
002aaa895
Fig 11. Alternate output mode
7.22.8 PLL operation
The PWM module features a Phase Locked Loop that can be used to generate a
CCUCLK frequency between 16 MHz and 32 MHz. At this frequency the PWM module
provides ultrasonic PWM frequency with 10-bit resolution provided that the crystal
frequency is 1 MHz or higher. The PLL is fed an input signal from 0.5 MHz to 1 MHz and
generates an output signal of 32 times the input frequency. This signal is used to clock the
timer. The user will have to set a divider that scales PCLK by a factor from 1 to 16. This
divider is found in the SFR register TCR21. The PLL frequency can be expressed as
shown in Equation 1:
PCLK
PLL frequency = -----------------N + 1
(1)
Where: N is the value of PLLDV3:0.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
43 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Since N ranges from 0 to 15, the CCLK frequency can be in the range of PCLK to
PCLK/16.
7.22.9 CCU interrupts
There are seven interrupt sources on the CCU which share a common interrupt vector.
EA (IEN0.7)
ECCU (IEN1.4)
TOIE2 (TICR2.7)
TOIF2 (TIFR2.7)
TICIE2A (TICR2.0)
TICF2A (TIFR2.0)
TICIE2B (TICR2.1)
TICF2B (TIFR2.1)
TOCIE2A (TICR2.3)
TOCF2A (TIFR2.3)
interrupt to
CPU
other
interrupt
sources
TOCIE2B (TICR2.4)
TOCF2B (TIFR2.4)
TOCIE2C (TICR2.5)
TOCF2C (TIFR2.5)
TOCIE2D (TICR2.6)
TOCF2D (TIFR2.6)
ENCINT.0
PRIORITY
ENCODER
ENCINT.1
ENCINT.2
002aaa896
Fig 12. Capture/compare unit interrupts
7.23 UART
The P89LPC9331/9341/9351/9361 has an enhanced UART that is compatible with the
conventional 80C51 UART except that Timer 2 overflow cannot be used as a baud rate
source. The P89LPC9331/9341/9351/9361 does include an independent baud rate
generator. The baud rate can be selected from the oscillator (divided by a constant),
Timer 1 overflow, or the independent baud rate generator. In addition to the baud rate
generation, enhancements over the standard 80C51 UART include Framing Error
detection, automatic address recognition, selectable double buffering and several
interrupt options. The UART can be operated in four modes: shift register, 8-bit UART,
9-bit UART, and CPU clock/32 or CPU clock/16.
7.23.1 Mode 0
Serial data enters and exits through RXD. TXD outputs the shift clock. 8 bits are
transmitted or received, LSB first. The baud rate is fixed at 1⁄16 of the CPU clock
frequency.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
44 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.23.2 Mode 1
10 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0),
8 data bits (LSB first), and a stop bit (logic 1). When data is received, the stop bit is stored
in RB8 in special function register SCON. The baud rate is variable and is determined by
the Timer 1 overflow rate or the baud rate generator (described in Section 7.23.5 “Baud
rate generator and selection”).
7.23.3 Mode 2
11 bits are transmitted (through TXD) or received (through RXD): start bit (logic 0), 8 data
bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). When data is
transmitted, the 9th data bit (TB8 in SCON) can be assigned the value of logic 0 or logic 1.
Or, for example, the parity bit (P, in the PSW) could be moved into TB8. When data is
received, the 9th data bit goes into RB8 in special function register SCON, while the stop
bit is not saved. The baud rate is programmable to either 1⁄16 or 1⁄32 of the CPU clock
frequency, as determined by the SMOD1 bit in PCON.
7.23.4 Mode 3
11 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0), 8
data bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). In fact, Mode 3 is
the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable
and is determined by the Timer 1 overflow rate or the baud rate generator (described in
Section 7.23.5 “Baud rate generator and selection”).
7.23.5 Baud rate generator and selection
The P89LPC9331/9341/9351/9361 enhanced UART has an independent baud rate
generator. The baud rate is determined by a baud-rate preprogrammed into the BRGR1
and BRGR0 SFRs which together form a 16-bit baud rate divisor value that works in a
similar manner as Timer 1 but is much more accurate. If the baud rate generator is used,
Timer 1 can be used for other timing functions.
The UART can use either Timer 1 or the baud rate generator output (see Figure 13). Note
that Timer T1 is further divided by 2 if the SMOD1 bit (PCON.7) is cleared. The
independent baud rate generators use OSCCLK.
timer 1 overflow
(PCLK-based)
SMOD1 = 1
SBRGS = 0
÷2
baud rate modes 1 and 3
SMOD1 = 0
baud rate generator
(CCLK-based)
SBRGS = 1
002aaa897
Fig 13. Baud rate sources for UART (Modes 1, 3)
7.23.6 Framing error
Framing error is reported in the status register (SSTAT). In addition, if SMOD0 (PCON.6)
is logic 1, framing errors can be made available in SCON.7 respectively. If SMOD0 is
logic 0, SCON.7 is SM0. It is recommended that SM0 and SM1 (SCON.7:6) are set up
when SMOD0 is logic 0.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
45 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.23.7 Break detect
Break detect is reported in the status register (SSTAT). A break is detected when
11 consecutive bits are sensed LOW. The break detect can be used to reset the device
and force the device into ISP mode.
7.23.8 Double buffering
The UART has a transmit double buffer that allows buffering of the next character to be
written to SnBUF while the first character is being transmitted. Double buffering allows
transmission of a string of characters with only one stop bit between any two characters,
as long as the next character is written between the start bit and the stop bit of the
previous character.
Double buffering can be disabled. If disabled (DBMOD, i.e., SSTAT.7 = 0), the UART is
compatible with the conventional 80C51 UART. If enabled, the UART allows writing to
SBUF while the previous data is being shifted out. Double buffering is only allowed in
Modes 1, 2 and 3. When operated in Mode 0, double buffering must be disabled
(DBMOD = 0).
7.23.9 Transmit interrupts with double buffering enabled (modes 1, 2 and 3)
Unlike the conventional UART, in double buffering mode, the TI interrupt is generated
when the double buffer is ready to receive new data.
7.23.10 The 9th bit (bit 8) in double buffering (modes 1, 2 and 3)
If double buffering is disabled TB8 can be written before or after SBUF is written, as long
as TB8 is updated some time before that bit is shifted out. TB8 must not be changed until
the bit is shifted out, as indicated by the TI interrupt.
If double buffering is enabled, TB must be updated before SBUF is written, as TB8 will be
double-buffered together with SBUF data.
7.24 I2C-bus serial interface
The I2C-bus uses two wires (SDA and SCL) to transfer information between devices
connected to the bus, and it has the following features:
• Bidirectional data transfer between masters and slaves
• Multi master bus (no central master)
• Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer
• The I2C-bus may be used for test and diagnostic purposes.
A typical I2C-bus configuration is shown in Figure 14. The P89LPC9331/9341/9351/9361
device provides a byte-oriented I2C-bus interface that supports data transfers up to
400 kHz.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
46 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
RP
RP
SDA
I2C-bus
SCL
P1.3/SDA
P1.2/SCL
P89LPC9331/9341/
9351/9361
OTHER DEVICE
WITH I2C-BUS
INTERFACE
OTHER DEVICE
WITH I2C-BUS
INTERFACE
002aad731
Fig 14. I2C-bus configuration
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
47 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8
I2ADR
ADDRESS REGISTER
P1.3
COMPARATOR
INPUT
FILTER
P1.3/SDA
SHIFT REGISTER
OUTPUT
STAGE
ACK
I2DAT
BIT COUNTER /
ARBITRATION
AND SYNC LOGIC
INPUT
FILTER
P1.2/SCL
SERIAL CLOCK
GENERATOR
OUTPUT
STAGE
CCLK
TIMING
AND
CONTROL
LOGIC
interrupt
INTERNAL BUS
8
timer 1
overflow
P1.2
I2CON
I2SCLH
I2SCLL
CONTROL REGISTERS AND
SCL DUTY CYCLE REGISTERS
8
status bus
I2STAT
STATUS
DECODER
STATUS REGISTER
8
002aaa899
Fig 15. I2C-bus serial interface block diagram
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
48 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.25 SPI
The P89LPC9331/9341/9351/9361 provides another high-speed serial communication
interface: the SPI interface. SPI is a full-duplex, high-speed, synchronous communication
bus with two operation modes: Master mode and Slave mode. Up to 3 Mbit/s can be
supported in either Master mode or Slave mode. It has a Transfer Completion Flag and
Write Collision Flag Protection.
S
M
CPU clock
8-BIT SHIFT REGISTER
clock
MSTR
SPR0
SPICLK
P2.5
SS
P2.4
SPR0
SPR1
CPOL
CPHA
MSTR
SSIG
WCOL
DORD
MSTR
SPEN
SPI CONTROL
SPEN
SPR1
S
M
CLOCK LOGIC
MOSI
P2.2
SPEN
SPI clock (master)
SELECT
SPIF
PIN
CONTROL
LOGIC
READ DATA BUFFER
DIVIDER
BY 4, 16, 64, 128
MISO
P2.3
M
S
SPI CONTROL REGISTER
SPI STATUS REGISTER
SPI
interrupt
request
internal
data
bus
002aaa900
Fig 16. SPI block diagram
The SPI interface has four pins: SPICLK, MOSI, MISO and SS:
• SPICLK, MOSI and MISO are typically tied together between two or more SPI
devices. Data flows from master to slave on MOSI (Master Out Slave In) pin and flows
from slave to master on MISO (Master In Slave Out) pin. The SPICLK signal is output
in the Master mode and is input in the Slave mode. If the SPI system is disabled, i.e.,
SPEN (SPCTL.6) = 0 (reset value), these pins are configured for port functions.
• SS is the optional slave select pin. In a typical configuration, an SPI master asserts
one of its port pins to select one SPI device as the current slave. An SPI slave device
uses its SS pin to determine whether it is selected.
Typical connections are shown in Figure 17 through Figure 19.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
49 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.25.1 Typical SPI configurations
master
8-BIT SHIFT
REGISTER
slave
MISO
MISO
MOSI
MOSI
SPICLK
SPI CLOCK
GENERATOR
PORT
8-BIT SHIFT
REGISTER
SPICLK
SS
002aaa901
Fig 17. SPI single master single slave configuration
master
8-BIT SHIFT
REGISTER
slave
MISO
MISO
MOSI
MOSI
SPICLK
SPI CLOCK
GENERATOR
SS
8-BIT SHIFT
REGISTER
SPICLK
SS
SPI CLOCK
GENERATOR
002aaa902
Fig 18. SPI dual device configuration, where either can be a master or a slave
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
50 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
master
slave
8-BIT SHIFT
REGISTER
MISO
MISO
MOSI
MOSI
SPICLK
SPI CLOCK
GENERATOR
port
8-BIT SHIFT
REGISTER
SPICLK
SS
slave
MISO
MOSI
8-BIT SHIFT
REGISTER
SPICLK
port
SS
002aaa903
Fig 19. SPI single master multiple slaves configuration
7.26 Analog comparators
Two analog comparators are provided on the P89LPC9331/9341/9351/9361. Input and
output options allow use of the comparators in a number of different configurations.
Comparator operation is such that the output is a logical one (which may be read in a
register and/or routed to a pin) when the positive input (one of two selectable inputs) is
greater than the negative input (selectable from a pin or an internal reference voltage).
Otherwise the output is a zero. Each comparator may be configured to cause an interrupt
when the output value changes.
In P89LPC9351/9361, the positive inputs of comparators could be amplified by
Programmable Gain Amplifier 1 (PGA1) module. The PGA1 can supply gain factors of 2x,
4x, 8x, or 16x, eliminating the need for external op-amps in the end application.
The overall connections to both comparators are shown in Figure 20 and Figure 21. The
comparators function to VDD = 2.4 V.
When each comparator is first enabled, the comparator output and interrupt flag are not
guaranteed to be stable for 10 s. The corresponding comparator interrupt should not be
enabled during that time, and the comparator interrupt flag must be cleared before the
interrupt is enabled in order to prevent an immediate interrupt service.
When a comparator is disabled the comparator’s output, COn, goes HIGH. If the
comparator output was LOW and then is disabled, the resulting transition of the
comparator output from a LOW to HIGH state will set the comparator flag, CMFn. This will
cause an interrupt if the comparator interrupt is enabled. The user should therefore
disable the comparator interrupt prior to disabling the comparator. Additionally, the user
should clear the comparator flag, CMFn, after disabling the comparator.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
51 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
CP1
comparator 1
(P0.4) CIN1A
(P0.3) CIN1B
OE1
CO1
(P0.5) CMPREF
Vref(bg)
CMP1 (P0.6)
change detect
CMF1
CN1
interrupt
change detect
EC
CP2
CMF2
comparator 2
(P0.2) CIN2A
(P0.1) CIN2B
CMP2 (P0.0)
CO2
OE2
CN2
002aae483
Fig 20. Comparator input and output connections (P89LPC9331/9341)
CP1
comparator 1
(P0.4) CIN1A
(P0.3) CIN1B
CO1
PGA1
(P0.2) CIN2A
(P0.1) CIN2B
OE1
(P0.5) CMPREF
Vref(bg)
CMP1 (P0.6)
change detect
CMF1
CN1
interrupt
change detect
EC
CP2
CMF2
comparator 2
CMP2 (P0.0)
CO2
OE2
CN2
002aad561
Fig 21. Comparator input and output connections (P89LPC9351/9361)
7.26.1 Internal reference voltage
An internal reference voltage generator may supply a default reference when a single
comparator input pin is used. The value of the internal reference voltage, referred to as
Vref(bg), is 1.23 V 10 %.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
52 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.26.2 Comparator interrupt
Each comparator has an interrupt flag contained in its configuration register. This flag is
set whenever the comparator output changes state. The flag may be polled by software or
may be used to generate an interrupt. The two comparators use one common interrupt
vector. If both comparators enable interrupts, after entering the interrupt service routine,
the user needs to read the flags to determine which comparator caused the interrupt.
7.26.3 Comparators and power reduction modes
Either or both comparators may remain enabled when Power-down or Idle mode is
activated, but both comparators are disabled automatically in Total Power-down mode.
If a comparator interrupt is enabled (except in Total Power-down mode), a change of the
comparator output state will generate an interrupt and wake-up the processor. If the
comparator output to a pin is enabled, the pin should be configured in the push-pull mode
in order to obtain fast switching times while in Power-down mode. The reason is that with
the oscillator stopped, the temporary strong pull-up that normally occurs during switching
on a quasi-bidirectional port pin does not take place.
Comparators consume power in Power-down and Idle modes, as well as in the normal
operating mode. This fact should be taken into account when system power consumption
is an issue. To minimize power consumption, the user can disable the comparators via
PCONA.5, or put the device in Total Power-down mode.
7.27 KBI
The Keypad Interrupt function (KBI) is intended primarily to allow a single interrupt to be
generated when Port 0 is equal to or not equal to a certain pattern. This function can be
used for bus address recognition or keypad recognition. The user can configure the port
via SFRs for different tasks.
The Keypad Interrupt Mask Register (KBMASK) is used to define which input pins
connected to Port 0 can trigger the interrupt. The Keypad Pattern Register (KBPATN) is
used to define a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag
(KBIF) in the Keypad Interrupt Control Register (KBCON) is set when the condition is
matched while the Keypad Interrupt function is active. An interrupt will be generated if
enabled. The PATN_SEL bit in the Keypad Interrupt Control Register (KBCON) is used to
define equal or not-equal for the comparison.
In order to use the Keypad Interrupt as an original KBI function like in P87LPC76x series,
the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then any key
connected to Port 0 which is enabled by the KBMASK register will cause the hardware to
set KBIF and generate an interrupt if it has been enabled. The interrupt may be used to
wake-up the CPU from Idle or Power-down modes. This feature is particularly useful in
handheld, battery-powered systems that need to carefully manage power consumption
yet also need to be convenient to use.
In order to set the flag and cause an interrupt, the pattern on Port 0 must be held longer
than six CCLKs.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
53 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.28 Watchdog timer
The watchdog timer causes a system reset when it underflows as a result of a failure to
feed the timer prior to the timer reaching its terminal count. It consists of a programmable
12-bit prescaler, and an 8-bit down counter. The down counter is decremented by a tap
taken from the prescaler. The clock source for the prescaler can be the PCLK, the nominal
400 kHz watchdog oscillator or low speed crystal oscillator. The watchdog timer can only
be reset by a power-on reset. When the watchdog feature is disabled, it can be used as
an interval timer and may generate an interrupt. Figure 22 shows the watchdog timer in
Watchdog mode. Feeding the watchdog requires a two-byte sequence. If PCLK is
selected as the watchdog clock and the CPU is powered down, the watchdog is disabled.
The watchdog timer has a time-out period that ranges from a few s to a few seconds.
Please refer to the P89LPC9331/9341/9351/9361 User manual for more details.
WDL (C1H)
MOV WFEED1, #0A5H
MOV WFEED2, #05AH
PCLK
0
watchdog
oscillator
1
0
crystal
oscillator
÷32
1
8-BIT DOWN
COUNTER
PRESCALER
reset(1)
XTALWD
SHADOW REGISTER
WDCON (A7H)
PRE2
PRE1
PRE0
-
-
WDRUN
WDTOF
WDCLK
002aae015
(1) Watchdog reset can also be caused by an invalid feed sequence, or by writing to WDCON not immediately followed by a feed
sequence.
Fig 22. Watchdog timer in Watchdog mode (WDTE = 1)
7.29 Additional features
7.29.1 Software reset
The SRST bit in AUXR1 gives software the opportunity to reset the processor completely,
as if an external reset or watchdog reset had occurred. Care should be taken when writing
to AUXR1 to avoid accidental software resets.
7.29.2 Dual data pointers
The dual Data Pointers (DPTR) provides two different Data Pointers to specify the
address used with certain instructions. The DPS bit in the AUXR1 register selects one of
the two Data Pointers. Bit 2 of AUXR1 is permanently wired as a logic 0 so that the DPS
bit may be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1
register, without the possibility of inadvertently altering other bits in the register.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
54 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
7.29.3 Data EEPROM (P89LPC9351/9361)
The P89LPC9351/9361 has 512 bytes of on-chip Data EEPROM. The Data EEPROM is
SFR based, byte readable, byte writable, and erasable (via row fill and sector fill). The
user can read, write and fill the memory via SFRs and one interrupt. This Data EEPROM
provides 100,000 minimum erase/program cycles for each byte.
• Byte mode: In this mode, data can be read and written one byte at a time.
• Row fill: In this mode, the addressed row (64 bytes) is filled with a single value. The
entire row can be erased by writing 00H.
• Sector fill: In this mode, all 512 bytes are filled with a single value. The entire sector
can be erased by writing 00H.
After the operation finishes, the hardware will set the EEIF bit, which if enabled will
generate an interrupt. The flag is cleared by software.
Remark: When voltage supply is lower than 2.4 V, the BOD EEPROM is tripped and Data
EEPROM program or erase is blocked. EWERR1 and EWERR0 bits are used to indicate
the write error for BOD EEPROM. Both can be cleared by power-on reset, watchdog reset
or software write.
7.30 Flash program memory
7.30.1 General description
The P89LPC9331/9341/9351/9361 flash memory provides in-circuit electrical erasure and
programming. The flash can be erased, read, and written as bytes. The Sector and Page
Erase functions can erase any flash sector (1 kB) or page (64 bytes). The Chip Erase
operation will erase the entire program memory. ICP using standard commercial
programmers is available. In addition, IAP and byte-erase allows code memory to be used
for non-volatile data storage. On-chip erase and write timing generation contribute to a
user-friendly programming interface. The P89LPC9331/9341/9351/9361 flash reliably
stores memory contents even after 100,000 erase and program cycles. The cell is
designed to optimize the erase and programming mechanisms. The
P89LPC9331/9341/9351/9361 uses VDD as the supply voltage to perform the
Program/Erase algorithms. When voltage supply is lower than 2.4 V, the BOD FLASH is
tripped and flash erase/program is blocked.
7.30.2 Features
•
•
•
•
•
Programming and erase over the full operating voltage range.
Byte erase allows code memory to be used for data storage.
Read/Programming/Erase using ISP/IAP/ICP.
Internal fixed boot ROM, containing low-level IAP routines available to user code.
Default loader providing ISP via the serial port, located in upper end of user program
memory.
• Boot vector allows user-provided flash loader code to reside anywhere in the flash
memory space, providing flexibility to the user.
• Any flash program/erase operation in 2 ms.
• Programming with industry-standard commercial programmers.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
55 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
• Programmable security for the code in the flash for each sector.
• 100,000 typical erase/program cycles for each byte.
• 10 year minimum data retention.
7.30.3 Flash organization
The program memory consists of sixteen 1 kB sectors on the P89LPC9361 devices and
eight 1 kB sectors on the P89LPC9341/9351 devices and four 1 kB sectors on the
P89LPC9331 device. Each sector can be further divided into 64-byte pages. In addition to
sector erase, page erase, and byte erase, a 64-byte page register is included which
allows from 1 byte to 64 bytes of a given page to be programmed at the same time,
substantially reducing overall programming time.
7.30.4 Using flash as data storage
The flash code memory array of this device supports individual byte erasing and
programming. Any byte in the code memory array may be read using the MOVC
instruction, provided that the sector containing the byte has not been secured (a MOVC
instruction is not allowed to read code memory contents of a secured sector). Thus any
byte in a non-secured sector may be used for non-volatile data storage.
7.30.5 Flash programming and erasing
Four different methods of erasing or programming of the flash are available. The flash
may be programmed or erased in the end-user application (IAP) under control of the
application’s firmware. Another option is to use the ICP mechanism. This ICP system
provides for programming through a serial clock/serial data interface. As shipped from the
factory, the upper 512 bytes of user code space contains a serial ISP routine allowing for
the device to be programmed in circuit through the serial port. The flash may also be
programmed or erased using a commercially available EPROM programmer which
supports this device. This device does not provide for direct verification of code memory
contents. Instead, this device provides a 32-bit CRC result on either a sector or the entire
user code space.
Remark: When voltage supply is lower than 2.4 V, the BOD FLASH is tripped and flash
erase/program is blocked.
7.30.6 ICP
ICP is performed without removing the microcontroller from the system. The ICP facility
consists of internal hardware resources to facilitate remote programming of the
P89LPC9331/9341/9351/9361 through a two-wire serial interface. The NXP ICP facility
has made in-circuit programming in an embedded application - using commercially
available programmers - possible with a minimum of additional expense in components
and circuit board area. The ICP function uses five pins. Only a small connector needs to
be available to interface your application to a commercial programmer in order to use this
feature. Additional details may be found in the P89LPC9331/9341/9351/9361 User
manual.
7.30.7 IAP
IAP is performed in the application under the control of the microcontroller’s firmware. The
IAP facility consists of internal hardware resources to facilitate programming and erasing.
The NXP IAP has made in-application programming in an embedded application possible
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
56 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
without additional components. Two methods are available to accomplish IAP. A set of
predefined IAP functions are provided in a Boot ROM and can be called through a
common interface, PGM_MTP. Several IAP calls are available for use by an application
program to permit selective erasing and programming of flash sectors, pages, security
bits, configuration bytes, and device ID. These functions are selected by setting up the
microcontroller’s registers before making a call to PGM_MTP at FF03H. The Boot ROM
occupies the program memory space at the top of the address space from FF00H to
FEFFH, thereby not conflicting with the user program memory space.
In addition, IAP operations can be accomplished through the use of four SFRs consisting
of a control/status register, a data register, and two address registers. Additional details
may be found in the P89LPC9331/9341/9351/9361 User manual.
7.30.8 ISP
ISP is performed without removing the microcontroller from the system. The ISP facility
consists of a series of internal hardware resources coupled with internal firmware to
facilitate remote programming of the P89LPC9331/9341/9351/9361 through the serial
port. This firmware is provided by NXP and embedded within each
P89LPC9331/9341/9351/9361 device. The NXP ISP facility has made in-system
programming in an embedded application possible with a minimum of additional expense
in components and circuit board area. The ISP function uses five pins (VDD, VSS, TXD,
RXD, and RST). Only a small connector needs to be available to interface your application
to an external circuit in order to use this feature.
7.30.9 Power-on reset code execution
The P89LPC9331/9341/9351/9361 contains two special flash elements: the Boot Vector
and the Boot Status bit. Following reset, the P89LPC9331/9341/9351/9361 examines the
contents of the Boot Status bit. If the Boot Status bit is set to zero, power-up execution
starts at location 0000H, which is the normal start address of the user’s application code.
When the Boot Status bit is set to a value other than zero, the contents of the Boot Vector
are used as the high byte of the execution address and the low byte is set to 00H.
Table 10 shows the factory default Boot Vector setting for these devices. A
factory-provided bootloader is pre-programmed into the address space indicated and
uses the indicated bootloader entry point to perform ISP functions. This code can be
erased by the user.
Remark: Users who wish to use this loader should take precautions to avoid erasing the
1 kB sector that contains this bootloader. Instead, the page erase function can be used to
erase the first eight 64-byte pages located in this sector.
A custom bootloader can be written with the Boot Vector set to the custom bootloader, if
desired.
Table 10.
Default boot vector values and ISP entry points
Device
Default
boot vector
Default
bootloader
entry point
Default bootloader
code range
1 kB sector
range
P89LPC9331
0FH
0F00H
0E00H to 0FFFH
0C00H to 0FFFH
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
57 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 10.
Default boot vector values and ISP entry points …continued
Device
Default
boot vector
Default
bootloader
entry point
Default bootloader
code range
1 kB sector
range
P89LPC9341
1FH
1F00H
1E00H to 1FFFH
1C00H to 1FFFH
P89LPC9351
1FH
1F00H
1E00H to 1FFFH
1C00H to 1FFFH
P89LPC9361
3FH
3F00H
3E00H to 3FFFH
3C00H to 3FFFH
7.30.10 Hardware activation of the bootloader
The bootloader can also be executed by forcing the device into ISP mode during a
power-on sequence (see the P89LPC9331/9341/9351/9361 User manual for specific
information). This has the same effect as having a non-zero status byte. This allows an
application to be built that will normally execute user code but can be manually forced into
ISP operation. If the factory default setting for the boot is changed, it will no longer point to
the factory pre-programmed ISP bootloader code. After programming the flash, the status
byte should be programmed to zero in order to allow execution of the user’s application
code beginning at address 0000H.
7.31 User configuration bytes
Some user-configurable features of the P89LPC9331/9341/9351/9361 must be defined at
power-up and therefore cannot be set by the program after start of execution. These
features are configured through the use of the flash byte UCFG1 and UCFG2. Please see
the P89LPC9331/9341/9351/9361 User manual for additional details.
7.32 User sector security bytes
There are 4/8/6 User Sector Security Bytes on the P89LPC9331/9341/9351/9361. Each
byte corresponds to one sector. Please see the P89LPC9331/9341/9351/9361 User
manual for additional details.
8. ADC
8.1 General description
The P89LPC9331/9341/9351/9361 has two 8-bit, 4-channel multiplexed successive
approximation analog-to-digital converter modules. An on-chip temperature sensor is
integrated within ADC0 and operates over wide temperature. In P89LPC9351/9361, two
high-speed programmable gain amplifiers (PGA) are integrated. The PGAs provide
selectable gains of 2x, 4x, 8x, or 16x. A block diagram of the ADC is shown in Figure 23
and Figure 24.
Each ADC consists of a 4-input multiplexer which feeds a sample-and-hold circuit
providing an input signal to comparator inputs. The control logic in combination with the
SAR drives a digital-to-analog converter which provides the other input to the comparator.
The output of the comparator is fed to the SAR.
8.2 Features and benefits
Two 8-bit, 4-channel multiplexed input, successive approximation ADCs.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
58 of 94
NXP Semiconductors
P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core
Programmable Gain Amplifier (PGA) with selectable gains of 2x, 4x, 8x, or 16x.
(P89LPC9351/9361)
On-chip wide range temperature sensor.
Four result registers for each A/D.
Six operating modes:
Fixed channel, single conversion mode.
Fixed channel, continuous conversion mode.
Auto scan, single conversion mode.
Auto scan, continuous conversion mode.
Dual channel, continuous conversion mode.
Single step mode.
Four conversion start modes:
Timer triggered start.
Start immediately.
Edge triggered.
Dual start immediately.
8-bit conversion time of 1.61 s at an A/D clock of 8.0 MHz.
Interrupt or polled operation.
Boundary limits interrupt.
DAC output to a port pin with high output impedance.
Clock divider.
Power-down mode.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
59 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
8.3 Block diagram
Anin00
Anin01
Anin02
Anin03
AD00
AD01
AD02
input MUX
comp
SAR
AD03
Vref(bg)
Vsen
input MUX
8
DAC0
AD10
AD11
AD12
AD13
Anin10
Anin11
Anin12
Anin13
CONTROL
LOGIC
input MUX
comp
SAR
8
DAC1
CCLK
4
to comparators
002aae463
Fig 23. P89LPC9331/9341 ADC block diagram
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
60 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
AD00
AD01
AD02
AD03
input MUX
PGA0
Vref(bg)
Vsen
Anin00
Anin01
Anin02
Anin03
comp
+
SAR
–
8
DAC0
AD10
AD11
AD12
AD13
PGA1
Anin10
Anin11
Anin12
Anin13
CONTROL
LOGIC
input MUX
comp
+
SAR
–
8
DAC1
CCLK
4
to comparators
002aad576
Fig 24. P89LPC9351/9361 ADC block diagram
8.4 PGA (P89LPC9351/9361)
Additional PGA module is integrated in each ADC module to improve the effective
resolution of the ADC. A single channel can be selected for amplification. The gain of PGA
can be programmable to 2, 4, 8 and 16. Please refer to Table 12 “Static characteristics” for
detailed specifications.
Register PGACONx and PGACONxB are used to for PGA configuration. Register
PGAxTRIM2X4X and PGAxTRIM8X16X provide trim value of PGA gain level. As
power-on, default trim value for each gain setting is loaded into the PGA trim registers.
For accurate measurements, offset calibration is required.
Please see the P89LPC9331/9341/9351/9361 User manual for detail configuration,
calibration, and usage information.
8.5 Temperature sensor
An on-chip wide-temperature range temperature sensor is integrated with ADC0 module.
It provides temperature sensing capability of 40 C ~ 85 C. It is necessary to measure
the 1.2 V reference voltage via the ADC before measuring temperature. In
P89LPC9351/9361, the reference voltage, temperature sensor and AD03 input pin
multiplex one input to PGA0. Please see the P89LPC9331/9341/9351/9361 User manual
for detail usage of temperature sensor.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
61 of 94
NXP Semiconductors
P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core
8.6 ADC operating modes
8.6.1 Fixed channel, single conversion mode
A single input channel can be selected for conversion. A single conversion will be
performed and the result placed in the result register pair which corresponds to the
selected input channel. An interrupt, if enabled, will be generated after the conversion
completes.
In P89LPC9351/9361, in fixed channel mode, the PGA channel selection is dependent on
the ADC channel selection. If PGA is enabled, all the selected channels for A/D
conversion will be amplified and the gain amplify level is the same.
8.6.2 Fixed channel, continuous conversion mode
A single input channel can be selected for continuous conversion. The results of the
conversions will be sequentially placed in the four result register. The user may select
whether an interrupt can be generated after every four conversions. Additional conversion
results will again cycle through the four result register, overwriting the previous results.
Continuous conversions continue until terminated by the user.
In P89LPC9351/9361, in fixed channel mode, the PGA channel selection is independent
and can be different to A/D conversion channel selection. If different, the gain of the
selected ADC channel is 1.
8.6.3 Auto scan, single conversion mode
Any combination of the four input channels can be selected for conversion. A single
conversion of each selected input will be performed and the result placed in the result
register which corresponds to the selected input channel. An interrupt, if enabled, will be
generated after all selected channels have been converted. If only a single channel is
selected this is equivalent to single channel, single conversion mode.
In P89LPC9351/9361, in auto scan mode, the PGA channel selection is dependent on the
ADC channel selection. If PGA is enabled, all the selected channel for A/D conversion will
be amplified and the gain amplify level is the same.
8.6.4 Auto scan, continuous conversion mode
Any combination of the four input channels can be selected for conversion. A conversion
of each selected input will be performed and the result placed in the result register which
corresponds to the selected input channel. An interrupt, if enabled, will be generated after
all selected channels have been converted. The process will repeat starting with the first
selected channel. Additional conversion results will again cycle through the eight result
register pairs, overwriting the previous results. Continuous conversions continue until
terminated by the user.
In P89LPC9351/9361, in auto scan mode, the PGA channel selection is dependent on the
ADC channel selection. If PGA is enabled, all the selected channel for A/D conversion will
be amplified and the gain amplify level is the same.
8.6.5 Dual channel, continuous conversion mode
This is a variation of the auto scan continuous conversion mode where conversion occurs
on two user-selectable inputs. The result of the conversion of the first channel is placed in
the result register, ADxDAT0. The result of the conversion of the second channel is placed
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
62 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
in result register, ADxDAT1. The first channel is again converted and its result stored in
ADxDAT2. The second channel is again converted and its result placed in ADxDAT3. An
interrupt is generated, if enabled, after every set of four conversions (two conversions per
channel).
In P89LPC9351/9361, in dual channel mode, the PGA channel selection is independent
and can be different to A/D conversion channel selection. If different, the gain of the
selected ADC channel is 1.
8.6.6 Single step mode
This special mode allows ‘single-stepping’ in an auto scan conversion mode. Any
combination of the four input channels can be selected for conversion. After each channel
is converted, an interrupt is generated, if enabled, and the A/D waits for the next start
condition. May be used with any of the start modes.
In P89LPC9351/9361, in single step mode, the PGA channel selection is independent and
can be different to A/D conversion channel selection. If different, the gain of the selected
ADC channel is 1.
8.7 Conversion start modes
8.7.1 Timer triggered start
An A/D conversion is started by the overflow of Timer 0. Once a conversion has started,
additional Timer 0 triggers are ignored until the conversion has completed. The Timer
triggered start mode is available in all ADC operating modes.
8.7.2 Start immediately
Programming this mode immediately starts a conversion. This start mode is available in all
ADC operating modes.
8.7.3 Edge triggered
An A/D conversion is started by rising or falling edge of P1.4. Once a conversion has
started, additional edge triggers are ignored until the conversion has completed. The edge
triggered start mode is available in all ADC operating modes.
8.7.4 Dual start immediately
Programming this mode starts a synchronized conversion of both A/D converters. This
start mode is available in all A/D operating modes. Both A/D converters must be in the
same operating mode. In the continuous conversion modes, both A/D converters must
select an identical number of channels. Any trigger of either A/D will start a simultaneous
conversion of both A/Ds.
8.8 Boundary limits interrupt
Each of the A/D converters has both a high and low boundary limit register. The user may
select whether an interrupt is generated when the conversion result is within (or equal to)
the high and low boundary limits or when the conversion result is outside the boundary
limits. An interrupt will be generated, if enabled, if the result meets the selected interrupt
criteria. The boundary limit may be disabled by clearing the boundary limit interrupt
enable.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
63 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
An early detection mechanism exists when the interrupt criteria has been selected to be
outside the boundary limits. In this case, after the four MSBs have been converted, these
four bits are compared with the four MSBs of the boundary high and low registers. If the
four MSBs of the conversion meet the interrupt criteria (i.e., outside the boundary limits)
an interrupt will be generated, if enabled. If the four MSBs do not meet the interrupt
criteria, the boundary limits will again be compared after all 8 bits have been converted.
The boundary status register (BNDSTA0) flags the channels which caused a boundary
interrupt.
8.9 DAC output to a port pin with high output impedance
Each ADC’s DAC block can be output to a port pin. In this mode, the ADxDAT3 register is
used to hold the value fed to the DAC. After a value has been written to the DAC (written
to ADxDAT3), the DAC output will appear on the channel 3 pin.
8.10 Clock divider
The ADC requires that its internal clock source be in the range of 320 kHz to 8 MHz to
maintain accuracy. A programmable clock divider that divides the clock from 1 to 8 is
provided for this purpose.
8.11 Power-down and Idle mode
In Idle mode the ADC, if enabled, will continue to function and can cause the device to exit
Idle mode when the conversion is completed if the A/D interrupt is enabled. In
Power-down mode or Total Power-down mode, the A/D, PGA and temperature sensor do
not function. If the PGAs, temperature sensor or the A/D are enabled, they will consume
power. Power can be reduced by disabling the PGA, temperature sensor and A/D.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
64 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
9. Limiting values
Table 11. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
Tamb(bias)
Conditions
Min
Max
Unit
bias ambient temperature
55
+125
C
Tstg
storage temperature
65
+150
C
IOH(I/O)
HIGH-level output current per
input/output pin
-
20
mA
IOL(I/O)
LOW-level output current per
input/output pin
-
20
mA
II/Otot(max)
maximum total input/output current
-
100
mA
Vxtal
crystal voltage
on XTAL1, XTAL2 pin to VSS
-
VDD + 0.5
V
Vn
voltage on any other pin
except XTAL1, XTAL2 to VSS
0.5
+5.5
V
Ptot(pack)
total power dissipation (per package)
based on package heat
transfer, not device power
consumption
-
1.5
W
VESD
electrostatic discharge voltage
human body model; all pins
3000
+3000
V
700
+700
V
[2]
charged device model; all
pins
[1]
The following applies to Table 11:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated
maximum.
b) Parameters are valid over ambient temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2]
Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.
system frequency
(MHz)
18
12
2.4
2.7
3.0
VDD (V)
3.3
3.6
002aae351
Fig 25. Frequency vs. supply voltage
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
65 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
10. Static characteristics
Table 12. Static characteristics
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.
Symbol
IDD(oper)
IDD(idle)
Parameter
operating supply current
Idle mode supply current
Min
Typ[1]
Max
Unit
VDD = 3.6 V; fosc = 12 MHz
[2]
-
10
15
mA
VDD = 3.6 V; fosc = 18 MHz
[2]
-
14
23
mA
VDD = 3.6 V; fosc = 12 MHz
[3]
-
2
3.5
mA
VDD = 3.6 V; fosc = 18 MHz
[3]
-
3
5
mA
-
20
40
A
Conditions
IDD(pd)
Power-down mode supply
current
VDD = 3.6 V; voltage
comparators powered down
[4]
IDD(tpd)
total Power-down mode
supply current
all devices except
P89LPC9331HDH;
VDD = 3.6 V
[5]
-
0.5
5
A
P89LPC9331HDH only;
VDD = 3.6 V
[5]
-
-
25
A
5
-
5000
V/S
(dV/dt)r
rise rate
VPOR
power-on reset voltage
-
-
0.5
V
VDDR
data retention supply
voltage
1.5
-
-
V
Vth(HL)
HIGH-LOW threshold
voltage
except SCL, SDA
0.22VDD
0.4VDD
-
V
VIL
LOW-level input voltage
SCL, SDA only
0.5
-
0.3VDD
V
Vth(LH)
LOW-HIGH threshold
voltage
except SCL, SDA
-
0.6VDD
0.7VDD
V
VIH
HIGH-level input voltage
SCL, SDA only
0.7VDD
-
5.5
V
Vhys
hysteresis voltage
port 1
VOL
VOH
LOW-level output voltage
HIGH-level output voltage
of VDD; to ensure power-on
reset signal
-
0.2VDD
-
V
IOL = 20 mA; VDD = 2.4 V to
3.6 V all ports, all modes
except high-Z
[6]
-
0.6
1.0
V
IOL = 3.2 mA; VDD = 2.4 V to
3.6 V all ports, all modes
except high-Z
[6]
-
0.2
0.3
V
IOH = 20 A;
VDD = 2.4 V to 3.6 V; all ports,
quasi-bidirectional mode
VDD 0.3
VDD 0.2
-
V
IOH = 3.2 mA;
VDD = 2.4 V to 3.6 V; all ports,
push-pull mode
VDD 0.7
VDD 0.4
-
V
IOH = 10 mA;
VDD = 2.4 V to 3.6 V; all ports,
push-pull mode
-
3.2
-
V
0.5
-
+4.0
V
[7]
0.5
-
+5.5
V
[8]
-
-
15
pF
Vxtal
crystal voltage
on XTAL1, XTAL2 pins; with
respect to VSS
Vn
voltage on any other pin
except XTAL1, XTAL2, VDD;
with respect to VSS
Ciss
input capacitance
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
66 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 12. Static characteristics …continued
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.
Symbol
IIL
Parameter
LOW-level input current
Min
Typ[1]
Max
Unit
[9]
-
-
80
A
-
-
1
A
30
-
450
A
10
-
30
k
Conditions
VI = 0.4 V
ILI
input leakage current
VI = VIL, VIH, or Vth(HL)
[10]
ITHL
HIGH-LOW transition
current
all ports; VI = 1.5 V at
VDD = 3.6 V
[11]
RRST_N(int) internal pull-up resistance
on pin RST
pin RST
Vref(bg)
band gap reference voltage
1.19
1.23
1.27
V
TCbg
band gap temperature
coefficient
-
10
20
ppm/
C
[1]
Typical ratings are not guaranteed. The values listed are at room temperature, 3 V.
[2]
The IDD(oper) specification is measured using an external clock with code while(1) {} executed from on-chip flash.
[3]
The IDD(idle) specification is measured using an external clock with no active peripherals, with the following functions disabled: real-time
clock and watchdog timer.
[4]
The IDD(pd) specification is measured using internal RC oscillator with the following functions disabled: comparators, real-time clock, and
watchdog timer.
[5]
The IDD(tpd) specification is measured using an external clock with the following functions disabled: comparators, real-time clock,
brownout detect, and watchdog timer.
[6]
See Section 9 “Limiting values” for steady state (non-transient) limits on IOL or IOH. If IOL/IOH exceeds the test condition, VOL/VOH may
exceed the related specification.
[7]
This specification can be applied to pins which have A/D input or analog comparator input functions when the pin is not being used for
those analog functions. When the pin is being used as an analog input pin, the maximum voltage on the pin must be limited to 4.0 V with
respect to VSS.
[8]
Pin capacitance is characterized but not tested.
[9]
Measured with port in quasi-bidirectional mode.
[10] Measured with port in high-impedance mode.
[11] Port pins source a transition current when used in quasi-bidirectional mode and externally driven from logic 1 to logic 0. This current is
highest when VI is approximately 2 V.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
67 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
10.1 Current characteristics
Note: The graphs provided are a statistical summary based on a limited number of
samples and only for information purposes. The performance characteristics listed are not
tested or guaranteed.
002aae363
16
18 MHz
IDD
(mA)
12
12 MHz
8
8 MHz
6 MHz
4
0
2.4
4 MHz
2.8
2 MHz
1 MHz
32 kHz
3.6
3.2
VDD (V)
Test conditions: normal mode, code while(1) {} executed from on-chip flash; using an external
clock.
Fig 26. IDD(oper) vs. frequency at +25 C
002aae364
16
18 MHz
IDD
(mA)
12
12 MHz
8
8 MHz
6 MHz
4
0
2.4
4 MHz
2.8
2 MHz
1 MHz
32 kHz
3.6
3.2
VDD (V)
Test conditions: normal mode, code while(1) {} executed from on-chip flash; using an external
clock.
Fig 27. IDD(oper) vs. frequency at 40 C
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
68 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
002aae365
16
18 MHz
IDD
(mA)
12
12 MHz
8
8 MHz
6 MHz
4
0
2.4
4 MHz
2.8
2 MHz
1 MHz
32 kHz
3.6
3.2
VDD (V)
Test conditions: normal mode, code while(1) {} executed from on-chip flash; using an external
clock.
Fig 28. IDD(oper) vs. frequency at +85 C
002aae366
5.0
18 MHz
IDD
(mA)
4.0
12 MHz
3.0
8 MHz
2.0
6 MHz
4 MHz
1.0
0.0
2.4
2 MHz
1 MHz
32 kHz
2.8
3.2
3.6
VDD (V)
Test conditions: idle mode entered executing code from on-chip flash; using an external clock with
no active peripherals, with the following functions disabled: real-time clock and watchdog timer.
Fig 29. IDD(idle) vs. frequency at +25 C
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
69 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
002aae367
5.0
18 MHz
IDD
(mA)
4.0
12 MHz
3.0
8 MHz
2.0
6 MHz
4 MHz
1.0
0.0
2.4
2 MHz
1 MHz
32 kHz
2.8
3.2
3.6
VDD (V)
Test conditions: idle mode entered executing code from on-chip flash; using an external clock with
no active peripherals, with the following functions disabled: real-time clock and watchdog timer.
Fig 30. IDD(idle) vs. frequency at 40 C
002aae368
5.0
18 MHz
IDD
(mA)
4.0
12 MHz
3.0
8 MHz
2.0
6 MHz
4 MHz
1.0
0.0
2.4
2 MHz
1 MHz
32 kHz
2.8
3.2
3.6
VDD (V)
Test conditions: idle mode entered executing code from on-chip flash; using an external clock with
no active peripherals, with the following functions disabled: real-time clock and watchdog timer.
Fig 31. IDD(idle) vs. frequency at +85 C
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
70 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
002aae369
20.0
IDD
(μA)
(1)
18.0
16.0
(2)
14.0
(3)
12.0
10.0
2.4
2.8
3.2
3.6
VDD (V)
Test conditions: power-down mode, using internal RC oscillator with the following functions
disabled: comparators, real-time clock, and watchdog timer.
(1) +85 C
(2) +25 C
(3) 40 C
Fig 32. IDD(pd) vs. VDD
002aae370
1.2
(1)
IDD
(μA)
0.8
0.4
(2)
(3)
0.0
2.4
2.8
3.2
3.6
VDD (V)
Test conditions: Total power-down mode, using internal RC oscillator with the following functions
disabled: comparators, brownout detect, real-time clock, and watchdog timer.
(1) +85 C
(2) 40 C
(3) +25 C
Fig 33. IDD(tpd) vs. VDD
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
71 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
10.2 Internal RC/watchdog oscillator characteristics
Note: The graphs provided are a statistical summary based on a limited number of
samples and only for information purposes. The performance characteristics listed are not
tested or guaranteed.
002aae344
0.2
frequency
deviation
(%)
0.1
0
−0.1
−0.2
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of internal RC oscillator = 7.3728 MHz
Fig 34. Average internal RC oscillator frequency vs. VDD at +25 C
002aae346
0.2
frequency
deviation
(%)
0.1
0
−0.1
−0.2
2.4
2.8
3.2
3.6
VDD (V)
Note: Central frequency of internal RC oscillator = 7.3728 MHz
Fig 35. Average internal RC oscillator frequency vs. VDD at 40 C
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
72 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
002aae347
0.2
frequency
deviation
(%)
0
−0.2
−0.4
−0.6
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of internal RC oscillator = 7.3728 MHz
Fig 36. Average internal RC oscillator frequency vs. VDD at +85 C
002aae348
2.5
frequency
deviation
(%)
1.5
0.5
−0.5
−1.5
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of watchdog oscillator = 400 KHz
Fig 37. Average watchdog oscillator frequency vs. VDD at +25 C
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
73 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
002aae349
0.5
frequency
deviation
(%)
−0.5
−1.5
−2.5
−3.5
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of watchdog oscillator = 400 KHz
Fig 38. Average watchdog oscillator frequency vs. VDD at 40 C
002aae350
1.5
frequency
deviation
(%)
0.5
−0.5
−1.5
−2.5
2.4
2.8
3.2
3.6
VDD (V)
Central frequency of watchdog oscillator = 400 KHz
Fig 39. Average watchdog oscillator frequency vs. VDD at +85 C
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
74 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
10.3 BOD characteristics
Table 13. BOD static characteristics
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.
Symbol
Parameter
Min
Typ[1]
Max
Unit
BOICFG1, BOICFG0 = 01
2.25
-
2.55
V
BOICFG1, BOICFG0 = 10
2.60
-
2.80
V
BOICFG1, BOICFG0 = 11
3.10
-
3.40
V
BOICFG1, BOICFG0 = 01
2.40
-
2.60
V
BOICFG1, BOICFG0 = 10
2.70
-
2.90
V
BOICFG1, BOICFG0 = 11
3.10
-
3.40
V
BOE1, BOE0 = 01
2.10
-
2.30
V
BOE1, BOE0 = 10
2.35
-
2.50
V
BOE1, BOE0 = 11
2.90
-
3.20
V
BOE1, BOE0 = 01
2.20
-
2.40
V
BOE1, BOE0 = 10
2.45
-
2.60
V
BOE1, BOE0 = 11
2.90
-
3.30
V
falling stage
2.25
-
2.60
V
rising stage
2.35
-
2.65
V
Conditions
BOD interrupt
trip voltage
Vtrip
falling stage
rising stage
BOD reset
Vtrip
trip voltage
falling stage
rising stage
BOD EEPROM/FLASH
Vtrip
[1]
trip voltage
Typical ratings are not guaranteed. The values listed are at room temperature, 3 V.
VDD
Vtrip
(BOF/BOIF
set by hardware)
(BOF/BOIF can be
cleared in software)
BOF/BOIF
002aae352
Fig 40. BOD interrupt/reset characteristics
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
75 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
11. Dynamic characteristics
Table 14. Dynamic characteristics (12 MHz)
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.[1][2]
Symbol
Parameter
Conditions
Min
Max
Min
fosc(RC)
internal RC oscillator
frequency
nominal f = 7.3728 MHz
trimmed to 1 % at
Tamb = 25 C; clock
doubler option = OFF
(default)
7.189
7.557
7.189
nominal f = 14.7456 MHz;
clock doubler option = ON,
VDD = 2.7 V to 3.6 V
14.378
15.114
14.378 15.114 MHz
380
420
380
420
kHz
0
12
-
-
MHz
83
-
-
-
ns
0
8
-
-
MHz
P1.5/RST pin
-
50
-
50
ns
any pin except P1.5/RST
-
15
-
15
ns
P1.5/RST pin
125
-
125
-
ns
any pin except P1.5/RST
50
-
50
-
ns
fosc(WD)
internal watchdog
oscillator frequency
fosc
oscillator frequency
Tcy(clk)
clock cycle time
fCLKLP
low-power select clock
frequency
Tamb = 25 C
see Figure 41
Variable clock
fosc = 12 MHz
Unit
Max
7.557 MHz
Glitch filter
tgr
tsa
glitch rejection time
signal acceptance time
External clock
tCHCX
clock HIGH time
see Figure 41
33
Tcy(clk) tCLCX
33
-
ns
tCLCX
clock LOW time
see Figure 41
33
Tcy(clk) tCHCX
33
-
ns
tCLCH
clock rise time
see Figure 41
-
8
-
8
ns
tCHCL
clock fall time
see Figure 41
-
8
-
8
ns
Shift register (UART mode 0)
TXLXL
serial port clock cycle
time
see Figure 42
16Tcy(clk)
-
1333
-
ns
tQVXH
output data set-up to
clock rising edge time
see Figure 42
13Tcy(clk)
-
1083
-
ns
tXHQX
output data hold after
clock rising edge time
see Figure 42
-
Tcy(clk) + 20
-
103
ns
tXHDX
input data hold after
clock rising edge time
see Figure 42
-
0
-
0
ns
tXHDV
input data valid to clock
rising edge time
see Figure 42
150
-
150
-
ns
0
CCLK⁄
6
0
2.0
MHz
-
CCLK⁄
4
-
3.0
MHz
SPI interface
fSPI
SPI operating frequency
slave
master
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
76 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 14. Dynamic characteristics (12 MHz) …continued
VDD = 2.4 V to 3.6 V unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.[1][2]
Symbol
TSPICYC
Parameter
Conditions
Min
Max
slave
6⁄
CCLK
-
500
-
ns
master
4⁄
CCLK
-
333
-
ns
250
-
250
-
ns
250
-
250
-
ns
master
2⁄
CCLK
-
165
-
ns
slave
3⁄
CCLK
-
250
-
ns
master
2⁄
CCLK
-
165
-
ns
slave
3⁄
CCLK
-
250
-
ns
100
-
100
-
ns
100
-
100
-
ns
0
120
0
120
ns
0
240
-
240
ns
-
240
-
240
ns
SPI cycle time
tSPILAG
SPI enable lag time
see Figure 43, 44, 45, 46
see Figure 45, 46
slave
see Figure 45, 46
slave
tSPIDSU
SPICLK HIGH time
SPICLK LOW time
SPI data set-up time
see Figure 43, 44, 45, 46
see Figure 43, 44, 45, 46
see Figure 43, 44, 45, 46
master or slave
tSPIDH
SPI data hold time
tSPIA
SPI access time
see Figure 43, 44, 45, 46
master or slave
see Figure 45, 46
slave
tSPIDIS
SPI disable time
tSPIDV
SPI enable to output
data valid time
see Figure 45, 46
slave
see Figure 43, 44, 45, 46
slave
master
-
167
-
167
ns
0
-
0
-
ns
SPI outputs (SPICLK,
MOSI, MISO)
-
100
-
100
ns
SPI inputs (SPICLK,
MOSI, MISO, SS)
-
2000
-
2000
ns
SPI outputs (SPICLK,
MOSI, MISO)
-
100
-
100
ns
SPI inputs (SPICLK,
MOSI, MISO, SS)
-
2000
-
2000
ns
tSPIOH
SPI output data hold
time
see Figure 43, 44, 45, 46
tSPIR
SPI rise time
see Figure 43, 44, 45, 46
tSPIF
Unit
Max
SPI enable lead time
tSPICLKL
fosc = 12 MHz
Min
tSPILEAD
tSPICLKH
Variable clock
SPI fall time
see Figure 43, 44, 45, 46
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
77 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 15. Dynamic characteristics (18 MHz)
VDD = 3.0 V to 3.6 V unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.[1][2]
Symbol Parameter
fosc(RC)
internal RC oscillator
frequency
fosc(WD)
internal watchdog
oscillator frequency
fosc
oscillator frequency
Tcy(clk)
clock cycle time
fCLKLP
low-power select clock
frequency
Conditions
Variable clock
fosc = 18 MHz
Unit
Min
Max
Min
nominal f = 7.3728 MHz
trimmed to 1 % at
Tamb = 25 C; clock
doubler option = OFF
(default)
7.189
7.557
7.189
nominal f = 14.7456 MHz;
clock doubler option = ON
14.378
15.114
14.378 15.114 MHz
380
420
380
420
kHz
0
18
-
-
MHz
Tamb = 25 C
see Figure 41
Max
7.557 MHz
55
-
-
-
ns
0
8
-
-
MHz
Glitch filter
tgr
tsa
glitch rejection time
signal acceptance time
P1.5/RST pin
-
50
-
50
ns
any pin except P1.5/RST
-
15
-
15
ns
P1.5/RST pin
125
-
125
-
ns
any pin except P1.5/RST
50
-
50
-
ns
External clock
tCHCX
clock HIGH time
see Figure 41
22
Tcy(clk) tCLCX
22
-
ns
tCLCX
clock LOW time
see Figure 41
22
Tcy(clk) tCHCX
22
-
ns
tCLCH
clock rise time
see Figure 41
-
5
-
5
ns
tCHCL
clock fall time
see Figure 41
-
5
-
5
ns
Shift register (UART mode 0)
TXLXL
serial port clock cycle
time
see Figure 42
16Tcy(clk)
-
888
-
ns
tQVXH
output data set-up to
clock rising edge time
see Figure 42
13Tcy(clk)
-
722
-
ns
tXHQX
output data hold after
clock rising edge time
see Figure 42
-
Tcy(clk) + 20
-
75
ns
tXHDX
input data hold after
clock rising edge time
see Figure 42
-
0
-
0
ns
tXHDV
input data valid to clock
rising edge time
see Figure 42
150
-
150
-
ns
0
CCLK⁄
6
0
3.0
MHz
-
CCLK⁄
4
-
4.5
MHz
slave
6⁄
CCLK
-
333
-
ns
master
4⁄
CCLK
-
222
-
ns
SPI interface
fSPI
SPI operating frequency
slave
master
TSPICYC
SPI cycle time
see Figure 43, 44, 45, 46
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
78 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
Table 15. Dynamic characteristics (18 MHz) …continued
VDD = 3.0 V to 3.6 V unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.[1][2]
Symbol Parameter
tSPILEAD
Conditions
Variable clock
Max
Min
Max
250
-
250
-
ns
250
-
250
-
ns
slave
3⁄
CCLK
-
167
-
ns
master
2⁄
CCLK
-
111
-
ns
slave
3⁄
CCLK
-
167
-
ns
master
2⁄
CCLK
-
111
-
ns
100
-
100
-
ns
100
-
100
-
ns
0
80
0
80
ns
0
160
-
160
ns
slave
-
160
-
160
ns
master
-
111
-
111
ns
0
-
0
-
ns
SPI outputs (SPICLK,
MOSI, MISO)
-
100
-
100
ns
SPI inputs (SPICLK,
MOSI, MISO, SS)
-
2000
-
2000
ns
SPI outputs (SPICLK,
MOSI, MISO)
-
100
-
100
ns
SPI inputs (SPICLK,
MOSI, MISO, SS)
-
2000
-
2000
ns
SPI enable lead time
see Figure 45, 46
SPI enable lag time
see Figure 45, 46
slave
tSPICLKH
tSPICLKL
tSPIDSU
SPICLK HIGH time
SPICLK LOW time
SPI data set-up time
see Figure 43, 44, 45, 46
see Figure 43, 44, 45, 46
see Figure 43, 44, 45, 46
master or slave
tSPIDH
SPI data hold time
see Figure 43, 44, 45, 46
master or slave
tSPIA
SPI access time
see Figure 45, 46
slave
tSPIDIS
SPI disable time
see Figure 45, 46
slave
tSPIDV
SPI enable to output
data valid time
see Figure 43, 44, 45, 46
tSPIOH
SPI output data hold
time
see Figure 43, 44, 45, 46
tSPIR
SPI rise time
see Figure 43, 44, 45, 46
tSPIF
Unit
Min
slave
tSPILAG
fosc = 18 MHz
SPI fall time
see Figure 43, 44, 45, 46
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
79 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
11.1 Waveforms
tCHCL
tCHCX
tCLCH
tCLCX
Tcy(clk)
002aaa907
Fig 41. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)
TXLXL
clock
tXHQX
tQVXH
output data
0
write to SBUF
input data
1
2
3
4
5
6
tXHDX
set TI
tXHDV
valid
7
valid
valid
valid
valid
valid
valid
valid
clear RI
set RI
002aaa906
Fig 42. Shift register mode timing
SS
TSPICYC
tSPIF
tSPICLKH
tSPICLKL
tSPIR
SPICLK
(CPOL = 0)
(output)
tSPIF
tSPICLKL
tSPIR
tSPICLKH
SPICLK
(CPOL = 1)
(output)
tSPIDSU
MISO
(input)
tSPIDH
tSPIDV
MOSI
(output)
LSB/MSB in
MSB/LSB in
tSPIOH
tSPIDV
tSPIR
tSPIF
master MSB/LSB out
master LSB/MSB out
002aaa908
Fig 43. SPI master timing (CPHA = 0)
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
80 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
SS
TSPICYC
tSPIF
tSPICLKL
tSPIR
tSPICLKH
SPICLK
(CPOL = 0)
(output)
tSPIF
tSPICLKL
tSPICLKH
SPICLK
(CPOL = 1)
(output)
tSPIDSU
MISO
(input)
tSPIDH
LSB/MSB in
MSB/LSB in
tSPIDV
MOSI
(output)
tSPIR
tSPIOH
tSPIDV
tSPIF
tSPIR
master MSB/LSB out
master LSB/MSB out
002aaa909
Fig 44. SPI master timing (CPHA = 1)
SS
tSPIF
tSPIR
TSPICYC
tSPILEAD
tSPIF
tSPICLKH
tSPICLKL
tSPIR
tSPILAG
SPICLK
(CPOL = 0)
(input)
tSPIF
tSPICLKL
tSPIR
tSPICLKH
SPICLK
(CPOL = 1)
(input)
tSPIOH
tSPIA
tSPIOH
tSPIDV
MISO
(output)
slave MSB/LSB out
tSPIDSU
MOSI
(input)
tSPIOH
tSPIDH
tSPIDIS
tSPIDV
slave LSB/MSB out
tSPIDSU
tSPIDSU
MSB/LSB in
not defined
tSPIDH
LSB/MSB in
002aaa910
Fig 45. SPI slave timing (CPHA = 0)
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
81 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
SS
tSPIF
tSPILEAD
tSPIR
TSPICYC
tSPIF
tSPIR
tSPICLKL
tSPILAG
tSPICLKH
SPICLK
(CPOL = 0)
(input)
tSPIF
tSPICLKL
SPICLK
(CPOL = 1)
(input)
tSPIR
tSPICLKH
tSPIOH
tSPIOH
tSPIOH
tSPIDV
tSPIDV
tSPIDV
tSPIDIS
tSPIA
MISO
(output)
slave LSB/MSB out
slave MSB/LSB out
not defined
tSPIDSU
MOSI
(input)
tSPIDH
tSPIDSU
MSB/LSB in
tSPIDH
LSB/MSB in
002aaa911
Fig 46. SPI slave timing (CPHA = 1)
11.2 ISP entry mode
Table 16. Dynamic characteristics, ISP entry mode
VDD = 2.4 V to 3.6 V, unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tVR
VDD active to RST active delay
time
pin RST
50
-
-
s
tRH
RST HIGH time
pin RST
1
-
32
s
tRL
RST LOW time
pin RST
1
-
-
s
VDD
tVR
tRH
RST
tRL
002aaa912
Fig 47. ISP entry waveform
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
82 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
12. Other characteristics
12.1 Comparator electrical characteristics
Table 17. Comparator electrical characteristics
VDD = 2.4 V to 3.6 V, unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.
Symbol
Parameter
VIO
input offset voltage
VIC
common-mode input voltage
CMRR
common-mode rejection ratio
Conditions
[1]
Min
Typ
Max
Unit
-
-
10
mV
0
-
VDD 0.3
V
-
-
50
dB
tres(tot)
total response time
-
250
500
ns
t(CE-OV)
chip enable to output valid time
-
-
10
s
ILI
input leakage current
-
-
1
A
[1]
0 V < VI < VDD
This parameter is characterized, but not tested in production.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
83 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
12.2 ADC/PGA/temperature sensor electrical characteristics
Table 18. ADC/PGA/temperature sensor electrical characteristics
VDD = 2.4 V to 3.6 V, unless otherwise specified.
Tamb = 40 C to +85 C for industrial applications, 40 C to +125 C extended, unless otherwise specified.
All limits valid for an external source impedance of less than 10 k.
Symbol
Parameter
Max
Unit
VIA
analog input voltage
Conditions
VSS 0.4 -
Min
Typ
VDD + 0.4
V
Cia
analog input capacitance
-
-
15
pF
ED
differential linearity error
-
-
1
LSB
EL(adj)
integral non-linearity
-
-
1
LSB
EO
offset error
-
-
2
LSB
EG
gain error
-
-
1
%
Eu(tot)
total unadjusted error
-
-
2
LSB
-
-
1
LSB
-
-
60
dB
MCTC
channel-to-channel matching
ct(port)
crosstalk between port inputs
SRin
input slew rate
-
-
100
V/ms
Tcy(ADC)
ADC clock cycle time
111
-
2000
ns
tADC
ADC conversion time
ADC enabled
-
-
13Tcy(ADC)
s
ts(PGA)
PGA settling time
within accuracy
of ADC
-
-
1
s
GPGA
PGA gain
G=1
0.95
1.00
1.05
V/V
G=2
1.87
1.97
2.07
V/V
G=4
3.70
3.89
4.08
V/V
G=8
7.22
7.60
7.98
V/V
G = 16
0 kHz to 100 kHz
PGA
14.38
15.14
15.90
V/V
tstartup
start-up time
-
-
2
s
Voffset(O)(nom)
nominal output offset voltage
-
100
-
mV
temperature sensor
Tamb = +25 C
Vsen
sensor voltage
-
570
-
mV
TC
temperature coefficient
-
11
-
mV/C
tstartup
start-up time
-
200
-
s
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
84 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
start trigger
adc_clk
1
2
3
4
5
6
7
8
9
10
11
12
13
clk
serial_data_out
D7
D6
D5
D4
D3
ADCDATA_REG
D2
D1
D0
ADCDATA
002aae371
Fig 48. ADC conversion timing
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
85 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
offset
error
EO
gain
error
EG
255
254
253
252
(2)
7
code
out
(1)
6
5
4
3
2
1 LSB
(ideal)
1
0
1
2
3
4
5
6
253
7
254
255
256
VIA (LSBideal)
offset error
EO
1 LSB =
VDDA − VSSA
256
002aae372
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
Fig 49. ADC characteristics
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
86 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
13. Package outline
PLCC28: plastic leaded chip carrier; 28 leads
SOT261-2
eD
y
eE
X
A
19
25
b1
ZE
18
26
bp
w M
28
1
E
HE
pin 1 index
e
A
A4 A1
12
4
β
(A 3)
k
5
11
Lp
v M A
ZD
e
D
detail X
B
HD
v M B
0
5
10 mm
scale
DIMENSIONS (mm dimensions are derived from the original inch dimensions)
A4
A1
b1 D(1) E(1)
bp
e
A3
eD
eE
HD
UNIT A
max.
min.
4.57
4.19
mm
inches
0.81
0.66
HE
k
10.92 10.92 12.57 12.57 1.22
11.58 11.58
1.27
9.91 9.91 12.32 12.32 1.07
11.43 11.43
0.51
0.25
3.05
0.53
0.33
0.180
0.02
0.165
0.01
0.12
0.021 0.032 0.456 0.456
0.05
0.013 0.026 0.450 0.450
0.43
0.39
0.43
0.39
Lp
v
w
y
1.44
1.02
0.18
0.18
0.1
ZD(1) ZE(1)
max. max.
2.16
β
2.16
45 o
0.495 0.495 0.048 0.057
0.007 0.007 0.004 0.085 0.085
0.485 0.485 0.042 0.040
Note
1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT261-2
112E08
MS-018
EDR-7319
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
01-11-15
Fig 50. PLCC28 package outline (SOT261-2)
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
87 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
TSSOP28: plastic thin shrink small outline package; 28 leads; body width 4.4 mm
D
SOT361-1
E
A
X
c
HE
y
v M A
Z
15
28
Q
A2
(A 3)
A1
pin 1 index
A
θ
Lp
1
L
14
detail X
w M
bp
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (2)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
1.1
0.15
0.05
0.95
0.80
0.25
0.30
0.19
0.2
0.1
9.8
9.6
4.5
4.3
0.65
6.6
6.2
1
0.75
0.50
0.4
0.3
0.2
0.13
0.1
0.8
0.5
8o
o
0
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT361-1
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-19
MO-153
Fig 51. TSSOP package outline (SOT361-1)
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
88 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
14. Abbreviations
Table 19.
Abbreviations
Acronym
Description
ADC
Analog to Digital Converter
CPU
Central Processing Unit
CCU
Capture/Compare Unit
CRC
Cyclic Redundancy Check
DAC
Digital to Analog Converter
EPROM
Erasable Programmable Read-Only Memory
EEPROM
Electrically Erasable Programmable Read-Only Memory
EMI
Electro-Magnetic Interference
LSB
Least Significant Bit
MSB
Most Significant Bit
PGA
Programmable Gain Amplifier
PLL
Phase-Locked Loop
PWM
Pulse Width Modulator
RAM
Random Access Memory
RC
Resistance-Capacitance
RTC
Real-Time Clock
SAR
Successive Approximation Register
SFR
Special Function Register
SPI
Serial Peripheral Interface
UART
Universal Asynchronous Receiver/Transmitter
WDT
WatchDog Timer
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
89 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
15. Revision history
Table 20.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
P89LPC9331_9341_9351_
9361 v.5.1
20120820
Product data sheet
-
P89LPC9331_9341_
9351_ 9361 v.5
Modifications:
P89LPC9331_9341_9351_
9361 v.5
Modifications:
•
Table 6 “Special function registers - P89LPC9351/9361”: Corrected reset value for
DEECON register.
20110110
•
•
Product data sheet
-
P89LPC9331_9341_
9351_ 9361 v.4
Table 12 “Static characteristics”: Added VPOR.
Section 7.19 “Reset”: Added sentence “When this pin functions as a reset input...”.
P89LPC9331_9341_9351_
9361 v.4
20100910
Product data sheet
-
P89LPC9331_9341_
9351_ 9361 v.3
P89LPC9331_9341_9351_
9361 v.3
20090602
Product data sheet
-
P89LPC9331_9341_
9351 v.2
P89LPC9331_9341_9351 v.2 20090505
Product data sheet
-
P89LPC9351 v.1
P89LPC9351 v.1
Preliminary data sheet
-
-
20081119
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
90 of 94
P89LPC9331/9341/9351/9361
NXP Semiconductors
8-bit microcontroller with accelerated two-clock 80C51 core
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
91 of 94
NXP Semiconductors
P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
92 of 94
NXP Semiconductors
P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core
18. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
2.1
Principal features . . . . . . . . . . . . . . . . . . . . . . . 1
2.2
Additional features . . . . . . . . . . . . . . . . . . . . . . 2
3
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
3.1
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3
4
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 5
6
Pinning information . . . . . . . . . . . . . . . . . . . . . . 6
6.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 8
7
Functional description . . . . . . . . . . . . . . . . . . 12
7.1
Special function registers . . . . . . . . . . . . . . . . 12
7.2
Enhanced CPU . . . . . . . . . . . . . . . . . . . . . . . . 30
7.3
Clocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.3.1
Clock definitions . . . . . . . . . . . . . . . . . . . . . . . 30
7.3.2
CPU clock (OSCCLK). . . . . . . . . . . . . . . . . . . 30
7.4
Crystal oscillator option. . . . . . . . . . . . . . . . . . 30
7.4.1
Low speed oscillator option . . . . . . . . . . . . . . 30
7.4.2
Medium speed oscillator option . . . . . . . . . . . 30
7.4.3
High speed oscillator option . . . . . . . . . . . . . . 30
7.5
Clock output . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.6
On-chip RC oscillator option . . . . . . . . . . . . . . 31
7.7
Watchdog oscillator option . . . . . . . . . . . . . . . 31
7.8
External clock input option . . . . . . . . . . . . . . . 31
7.9
Clock source switching on the fly . . . . . . . . . . 31
7.10
CCLK wake-up delay . . . . . . . . . . . . . . . . . . . 32
7.11
CCLK modification: DIVM register . . . . . . . . . 32
7.12
Low power select . . . . . . . . . . . . . . . . . . . . . . 32
7.13
Memory organization . . . . . . . . . . . . . . . . . . . 33
7.14
Data RAM arrangement . . . . . . . . . . . . . . . . . 33
7.15
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.15.1
External interrupt inputs . . . . . . . . . . . . . . . . . 34
7.16
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.16.1
Port configurations . . . . . . . . . . . . . . . . . . . . . 36
7.16.1.1 Quasi-bidirectional output configuration . . . . . 36
7.16.1.2 Open-drain output configuration . . . . . . . . . . . 36
7.16.1.3 Input-only configuration . . . . . . . . . . . . . . . . . 37
7.16.1.4 Push-pull output configuration . . . . . . . . . . . . 37
7.16.2
Port 0 analog functions . . . . . . . . . . . . . . . . . . 37
7.16.3
Additional port features. . . . . . . . . . . . . . . . . . 37
7.17
Power monitoring functions . . . . . . . . . . . . . . 37
7.17.1
Brownout detection . . . . . . . . . . . . . . . . . . . . . 38
7.17.2
Power-on detection. . . . . . . . . . . . . . . . . . . . . 38
7.18
Power reduction modes . . . . . . . . . . . . . . . . . 38
7.18.1
Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.18.2
Power-down mode . . . . . . . . . . . . . . . . . . . . . 38
7.18.3
7.19
7.19.1
7.20
7.20.1
7.20.2
7.20.3
7.20.4
7.20.5
7.20.6
7.21
7.22
7.22.1
7.22.2
7.22.3
7.22.4
7.22.5
7.22.6
7.22.7
7.22.8
7.22.9
7.23
7.23.1
7.23.2
7.23.3
7.23.4
7.23.5
7.23.6
7.23.7
7.23.8
7.23.9
7.23.10
7.24
7.25
7.25.1
7.26
7.26.1
7.26.2
7.26.3
7.27
7.28
7.29
7.29.1
7.29.2
7.29.3
7.30
Total Power-down mode . . . . . . . . . . . . . . . .
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset vector. . . . . . . . . . . . . . . . . . . . . . . . . .
Timers/counters 0 and 1 . . . . . . . . . . . . . . . .
Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer overflow toggle output . . . . . . . . . . . . .
RTC/system timer . . . . . . . . . . . . . . . . . . . . .
CCU (P89LPC9351/9361) . . . . . . . . . . . . . . .
CCU clock . . . . . . . . . . . . . . . . . . . . . . . . . . .
CCUCLK prescaling. . . . . . . . . . . . . . . . . . . .
Basic timer operation . . . . . . . . . . . . . . . . . . .
Output compare . . . . . . . . . . . . . . . . . . . . . . .
Input capture . . . . . . . . . . . . . . . . . . . . . . . . .
PWM operation . . . . . . . . . . . . . . . . . . . . . . .
Alternating output mode. . . . . . . . . . . . . . . . .
PLL operation. . . . . . . . . . . . . . . . . . . . . . . . .
CCU interrupts . . . . . . . . . . . . . . . . . . . . . . . .
UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Baud rate generator and selection. . . . . . . . .
Framing error . . . . . . . . . . . . . . . . . . . . . . . . .
Break detect. . . . . . . . . . . . . . . . . . . . . . . . . .
Double buffering. . . . . . . . . . . . . . . . . . . . . . .
Transmit interrupts with double buffering
enabled (modes 1, 2 and 3) . . . . . . . . . . . . . .
The 9th bit (bit 8) in double buffering
(modes 1, 2 and 3). . . . . . . . . . . . . . . . . . . . .
I2C-bus serial interface. . . . . . . . . . . . . . . . . .
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical SPI configurations . . . . . . . . . . . . . . .
Analog comparators . . . . . . . . . . . . . . . . . . . .
Internal reference voltage . . . . . . . . . . . . . . .
Comparator interrupt . . . . . . . . . . . . . . . . . . .
Comparators and power reduction modes . . .
KBI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog timer . . . . . . . . . . . . . . . . . . . . . . .
Additional features . . . . . . . . . . . . . . . . . . . . .
Software reset . . . . . . . . . . . . . . . . . . . . . . . .
Dual data pointers . . . . . . . . . . . . . . . . . . . . .
Data EEPROM (P89LPC9351/9361) . . . . . . .
Flash program memory . . . . . . . . . . . . . . . . .
39
39
40
40
40
40
40
40
40
41
41
41
41
41
41
42
42
42
43
43
44
44
44
45
45
45
45
45
46
46
46
46
46
49
50
51
52
53
53
53
54
54
54
54
55
55
continued >>
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 5.1 — 20 August 2012
© NXP B.V. 2012. All rights reserved.
93 of 94
NXP Semiconductors
P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core
7.30.1
General description . . . . . . . . . . . . . . . . . . . . 55
7.30.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
7.30.3
Flash organization . . . . . . . . . . . . . . . . . . . . . 56
7.30.4
Using flash as data storage . . . . . . . . . . . . . . 56
7.30.5
Flash programming and erasing . . . . . . . . . . . 56
7.30.6
ICP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
7.30.7
IAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
7.30.8
ISP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.30.9
Power-on reset code execution . . . . . . . . . . . 57
7.30.10 Hardware activation of the bootloader . . . . . . 58
7.31
User configuration bytes . . . . . . . . . . . . . . . . . 58
7.32
User sector security bytes . . . . . . . . . . . . . . . 58
8
ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
8.1
General description . . . . . . . . . . . . . . . . . . . . 58
8.2
Features and benefits . . . . . . . . . . . . . . . . . . . 58
8.3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . 60
8.4
PGA (P89LPC9351/9361) . . . . . . . . . . . . . . . 61
8.5
Temperature sensor . . . . . . . . . . . . . . . . . . . . 61
8.6
ADC operating modes . . . . . . . . . . . . . . . . . . 62
8.6.1
Fixed channel, single conversion mode . . . . . 62
8.6.2
Fixed channel, continuous conversion mode . 62
8.6.3
Auto scan, single conversion mode . . . . . . . . 62
8.6.4
Auto scan, continuous conversion mode . . . . 62
8.6.5
Dual channel, continuous conversion mode . . 62
8.6.6
Single step mode . . . . . . . . . . . . . . . . . . . . . . 63
8.7
Conversion start modes . . . . . . . . . . . . . . . . . 63
8.7.1
Timer triggered start . . . . . . . . . . . . . . . . . . . . 63
8.7.2
Start immediately . . . . . . . . . . . . . . . . . . . . . . 63
8.7.3
Edge triggered . . . . . . . . . . . . . . . . . . . . . . . . 63
8.7.4
Dual start immediately . . . . . . . . . . . . . . . . . . 63
8.8
Boundary limits interrupt . . . . . . . . . . . . . . . . . 63
8.9
DAC output to a port pin with high output
impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
8.10
Clock divider . . . . . . . . . . . . . . . . . . . . . . . . . . 64
8.11
Power-down and Idle mode . . . . . . . . . . . . . . 64
9
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 65
10
Static characteristics. . . . . . . . . . . . . . . . . . . . 66
10.1
Current characteristics . . . . . . . . . . . . . . . . . . 68
10.2
Internal RC/watchdog oscillator characteristics 72
10.3
BOD characteristics . . . . . . . . . . . . . . . . . . . . 75
11
Dynamic characteristics . . . . . . . . . . . . . . . . . 76
11.1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
11.2
ISP entry mode . . . . . . . . . . . . . . . . . . . . . . . . 82
12
Other characteristics . . . . . . . . . . . . . . . . . . . . 83
12.1
Comparator electrical characteristics . . . . . . . 83
12.2
ADC/PGA/temperature sensor electrical
characteristics. . . . . . . . . . . . . . . . . . . . . . . . . 84
13
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 87
14
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 89
15
16
16.1
16.2
16.3
16.4
17
18
Revision history . . . . . . . . . . . . . . . . . . . . . . .
Legal information . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information . . . . . . . . . . . . . . . . . . . .
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
91
91
91
91
92
92
93
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2012.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 20 August 2012
Document identifier: P89LPC9331_9341_9351_9361
工商网监
湘ICP备2023018690号
