PCA9532PW/S908,118

PCA9532 16-bit I2C-bus LED dimmer Rev. 4.1 — 22 August 2016 Product data sheet 1. General description The PCA9532 is a 16-bit I2C-bus and SMBus I/O expander optimized for dimming LEDs in 256 discrete steps for Red/Green/Blue (RGB) color mixing and back light applications. The PCA9532 contains an internal oscillator with two user programmable blink rates and duty cycles coupled to the output PWM. The LED brightness is controlled by setting the blink rate high enough (> 100 Hz) that the blinking cannot be seen and then using the duty cycle to vary the amount of time the LED is on and thus the average current through the LED. The initial setup sequence programs the two blink rates/duty cycles for each individual PWM. From then on, only one command from the bus master is required to turn individual LEDs ON, OFF, BLINK RATE 1 or BLINK RATE 2. Based on the programmed frequency and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the LEDs to appear at a different brightness or blink at periods up to 1.69 second. The open-drain outputs directly drive the LEDs with maximum output sink current of 25 mA per bit and 200 mA per package (100 mA per octal). To blink LEDs at periods greater than 1.69 second the bus master (MCU, MPU, DSP, chip set, etc.) must send repeated commands to turn the LED on and off as is currently done when using normal I/O expanders like the NXP Semiconductors PCF8575 or PCA9555. Any bits not used for controlling the LEDs can be used for General Purpose parallel Input/Output (GPIO) expansion, which provides a simple solution when additional I/O is needed for ACPI power switches, sensors, push-buttons, alarm monitoring, fans, etc. The active LOW hardware reset pin (RESET) and Power-On Reset (POR) initializes the registers to their default state, all zeroes, causing the bits to be set HIGH (LED off). Three hardware address pins on the PCA9532 allow eight devices to operate on the same bus. 2. Features and benefits  16 LED drivers (on, off, flashing at a programmable rate)  Two selectable, fully programmable blink rates (frequency and duty cycle) between 0.591 Hz and 152 Hz (1.69 second and 6.58 milliseconds)  256 brightness steps  Input/outputs not used as LED drivers can be used as regular GPIOs  Internal oscillator requires no external components  I2C-bus interface logic compatible with SMBus  Internal power-on reset PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer           Noise filter on SCL/SDA inputs Active LOW reset input 16 open-drain outputs directly drive LEDs to 25 mA Controlled edge rates to minimize ground bounce No glitch on power-up Supports hot insertion Low standby current Operating power supply voltage range of 2.3 V to 5.5 V 0 Hz to 400 kHz clock frequency ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101  Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA  Packages offered: SO24, TSSOP24, HVQFN24 3. Ordering information Table 1. Ordering information Tamb = 40 C to +85 C. Type number Topside mark Package Name Description Version PCA9532D PCA9532D SO24 plastic small outline package; 24 leads; body width 7.5 mm SOT137-1 PCA9532PW PCA9532PW TSSOP24 plastic thin shrink small outline package; 24 leads; body width 4.4 mm SOT355-1 PCA9532BS 9532 plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4  4  0.85 mm SOT616-1 HVQFN24 4. Block diagram A0 A1 A2 PCA9532 SCL SDA INPUT REGISTER INPUT FILTERS I2C-BUS CONTROL LED SELECT (LSn) REGISTER 0 VDD RESET 1 POWER-ON RESET OSCILLATOR PRESCALER 0 REGISTER PWM0 REGISTER BLINK0 PRESCALER 1 REGISTER PWM1 REGISTER BLINK1 LEDn VSS 002aae521 Only one I/O shown for clarity. Fig 1. Block diagram of PCA9532 PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 2 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 5. Pinning information 5.1 Pinning A0 1 24 VDD A0 1 24 VDD A1 2 23 SDA A1 2 23 SDA A2 3 22 SCL A2 3 22 SCL LED0 4 21 RESET LED0 4 21 RESET LED1 5 20 LED15 LED1 5 20 LED15 LED2 6 19 LED14 LED2 6 LED3 7 18 LED13 LED3 7 LED4 8 17 LED12 LED4 8 17 LED12 LED5 9 16 LED11 LED5 9 16 LED11 LED6 10 15 LED10 LED6 10 15 LED10 LED7 11 14 LED9 LED7 11 14 LED9 VSS 12 13 LED8 VSS 12 13 LED8 PCA9532D PCA9532PW 002aae518 18 LED13 002aae519 Pin configuration for TSSOP24 19 SCL 20 SDA 21 VDD 24 A2 terminal 1 index area 22 A0 Fig 3. 23 A1 Pin configuration for SO24 LED0 1 18 RESET LED1 2 17 LED15 LED2 3 LED3 4 LED4 5 14 LED12 LED5 6 13 LED11 16 LED14 15 LED13 LED10 12 9 VSS LED9 11 8 LED8 10 7 LED7 PCA9532BS LED6 Fig 2. 19 LED14 002aae520 Transparent top view Fig 4. PCA9532 Product data sheet Pin configuration for HVQFN24 All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 3 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 5.2 Pin description Table 2. Symbol Pin description Pin Description SO24, TSSOP24 A0 1 22 address input 0 A1 2 23 address input 1 A2 3 24 address input 2 LED0 4 1 LED driver 0 LED1 5 2 LED driver 1 LED2 6 3 LED driver 2 LED3 7 4 LED driver 3 LED4 8 5 LED driver 4 LED5 9 6 LED driver 5 LED6 10 7 LED driver 6 LED7 11 8 LED driver 7 VSS 12 9[1] supply ground LED8 13 10 LED driver 8 LED9 14 11 LED driver 9 LED10 15 12 LED driver 10 LED11 16 13 LED driver 11 LED12 17 14 LED driver 12 LED13 18 15 LED driver 13 LED14 19 16 LED driver 14 LED15 20 17 LED driver 15 RESET 21 18 reset input (active LOW) SCL 22 19 serial clock line SDA 23 20 serial data line VDD 24 21 supply voltage [1] PCA9532 Product data sheet HVQFN24 HVQFN24 package die supply ground is connected to both VSS pin and exposed center pad. VSS pin must be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad on the board and for proper heat conduction through the board, thermal vias need to be incorporated in the PCB in the thermal pad region. All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 4 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 6. Functional description Refer to Figure 1 “Block diagram of PCA9532”. 6.1 Device address Following a START condition, the bus master must output the address of the slave it is accessing. The address of the PCA9532 is shown in Figure 5. To conserve power, no internal pull-up resistors are incorporated on the hardware selectable address pins and they must be pulled HIGH or LOW. slave address 1 1 0 0 fixed A2 A1 A0 R/W hardware selectable 002aac505 Fig 5. PCA9532 slave address The last bit of the address byte defines the operation to be performed. When set to logic 1 a read is selected, while a logic 0 selects a write operation. 6.2 Control register Following the successful acknowledgement of the slave address, the bus master will send a byte to the PCA9532, which will be stored in the Control register. 0 0 0 AI Auto-Increment flag B3 B2 B1 B0 register address 002aae523 Reset state: 00h Fig 6. Control register The lowest 4 bits are used as a pointer to determine which register will be accessed. If the Auto-Increment (AI) flag is set, the four low order bits of the Control register are automatically incremented after a read or write. This allows the user to program the registers sequentially. The contents of these bits will rollover to ‘0000’ after the last register is accessed. When Auto-Increment flag is set (AI = 1) and a read sequence is initiated, the sequence must start by reading a register different from the INPUT0 register (B3 B2 B1 B0  0 0 0 0). Only the 4 least significant bits are affected by the AI flag. Unused bits must be programmed with zeroes. PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 5 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 6.2.1 Control register definition Table 3. Register summary B3 B2 B1 B0 Symbol Access Description 0 0 0 0 INPUT0 read only input register 0 0 0 0 1 INPUT1 read only input register 1 0 0 1 0 PSC0 read/write frequency prescaler 0 0 0 1 1 PWM0 read/write PWM register 0 0 1 0 0 PSC1 read/write frequency prescaler 1 0 1 0 1 PWM1 read/write PWM register 1 0 1 1 0 LS0 read/write LED0 to LED3 selector 0 1 1 1 LS1 read/write LED4 to LED7 selector 1 0 0 0 LS2 read/write LED8 to LED11 selector 1 0 0 1 LS3 read/write LED12 to LED15 selector 6.3 Register descriptions 6.3.1 INPUT0 - Input register 0 The INPUT0 register reflects the state of the device pins (inputs 0 to 7). Writes to this register will be acknowledged but will have no effect. Table 4. Bit INPUT0 - Input register 0 description 7 6 5 4 3 2 1 0 Symbol LED7 LED6 LED5 LED4 LED3 LED2 LED1 LED0 Default X X X X X X X X Remark: The default value ‘X’ is determined by the externally applied logic level (normally logic 1) when used for directly driving LED with pull-up to VDD. 6.3.2 INPUT1 - Input register 1 The INPUT1 register reflects the state of the device pins (inputs 8 to 15). Writes to this register will be acknowledged but will have no effect. Table 5. Bit INPUT1 - Input register 1 description 7 6 5 4 3 2 1 0 Symbol LED15 LED14 LED13 LED12 LED11 LED10 LED9 LED8 Default X X X X X X X X Remark: The default value ‘X’ is determined by the externally applied logic level (normally logic 1) when used for directly driving LED with pull-up to VDD. PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 6 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 6.3.3 PCS0 - Frequency Prescaler 0 PSC0 is used to program the period of the PWM output. The period of BLINK0 = (PSC0 + 1) / 152. Table 6. Bit PSC0 - Frequency Prescaler 0 register description 7 6 5 4 3 2 1 0 Symbol PSC0[7] PSC0[6] PSC0[5] PSC0[4] PSC0[3] PSC0[2] PSC0[1] PSC0[0] Default 0 0 0 0 0 0 0 0 6.3.4 PWM0 - Pulse Width Modulation 0 The PWM0 register determines the duty cycle of BLINK0. The outputs are LOW (LED on) when the count is less than the value in PWM0 and HIGH (LED off) when it is greater. If PWM0 is programmed with 00h, then the PWM0 output is always HIGH (LED off). The duty cycle of BLINK0 = PWM0 / 256. Table 7. Bit PWM0 - Pulse Width Modulation 0 register description 7 6 5 4 3 2 1 0 Symbol PWM0 [7] PWM0 [6] PWM0 [5] PWM0 [4] PWM0 [3] PWM0 [2] PWM0 [1] PWM0 [0] Default 1 0 0 0 0 0 0 0 6.3.5 PCS1 - Frequency Prescaler 1 PSC1 is used to program the period of the PWM output. The period of BLINK1 = (PSC1 + 1) / 152. Table 8. Bit PSC1 - Frequency Prescaler 1 register description 7 6 5 4 3 2 1 0 Symbol PSC1[7] PSC1[6] PSC1[5] PSC1[4] PSC1[3] PSC1[2] PSC1[1] PSC1[0] Default 0 0 0 0 0 0 0 0 6.3.6 PWM1 - Pulse Width Modulation 1 The PWM1 register determines the duty cycle of BLINK1. The outputs are LOW (LED on) when the count is less than the value in PWM1 and HIGH (LED off) when it is greater. If PWM1 is programmed with 00h, then the PWM1 output is always HIGH (LED off). The duty cycle of BLINK1 = PWM1 / 256. Table 9. Bit PCA9532 Product data sheet PWM1 - Pulse Width Modulation 1 register description 7 6 5 4 3 2 1 0 Symbol PWM1 [7] PWM1 [6] PWM1 [5] PWM1 [4] PWM1 [3] PWM1 [2] PWM1 [1] PWM1 [0] Default 1 0 0 0 0 0 0 0 All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 7 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 6.3.7 LS0 to LS3 - LED selector registers The LSn LED selector registers determine the source of the LED data. 00 = output is set high-impedance (LED off; default) 01 = output is set LOW (LED on) 10 = output blinks at PWM0 rate 11 = output blinks at PWM1 rate Table 10. LS0 to LS3 - LED selector registers bit description Legend: * default value. Register Bit Value Description LS0 - LED0 to LED3 selector LS0 7:6 00* LED3 selected 5:4 00* LED2 selected 3:2 00* LED1 selected 1:0 00* LED0 selected LS1 - LED4 to LED7 selector LS1 7:6 00* LED7 selected 5:4 00* LED6 selected 3:2 00* LED5 selected 1:0 00* LED4 selected LS2 - LED8 to LED11 selector LS2 7:6 00* LED11 selected 5:4 00* LED10 selected 3:2 00* LED9 selected 1:0 00* LED8 selected LS3 - LED12 to LED15 selector LS3 PCA9532 Product data sheet 7:6 00* LED15 selected 5:4 00* LED14 selected 3:2 00* LED13 selected 1:0 00* LED12 selected All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 8 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 6.4 Pins used as GPIOs LEDn pins not used to control LEDs can be used as General Purpose I/Os (GPIOs). For use as input, set LEDn to high-impedance (00) and then read the pin state via the INPUT0 or INPUT1 register. For use as output, connect external pull-up resistor to the pin and size it according to the DC recommended operating characteristics. LEDn output pin is HIGH when the output is programmed as high-impedance, and LOW when the output is programmed LOW through the ‘LED selector’ register. The output can be pulse-width controlled when PWM0 or PWM1 are used. 6.5 Power-on reset When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9532 in a reset condition until VDD has reached VPOR. At that point, the reset condition is released and the PCA9532 registers are initialized to their default states, all the outputs in the OFF state. Thereafter, VDD must be lowered below 0.2 V to reset the device. 6.6 External RESET A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst). The PCA9532 registers and I2C-bus state machine will be held in their default states until the RESET input is once again HIGH. This input requires a pull-up resistor to VDD if no active connection is used. PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 9 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 7. Characteristics of the I2C-bus The I2C-bus is for 2-way, 2-line communication between different ICs or modules. The two lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus is not busy. 7.1 Bit transfer One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse as changes in the data line at this time will be interpreted as control signals (see Figure 7). 6'$ 6&/ GDWDOLQH VWDEOH GDWDYDOLG Fig 7. FKDQJH RIGDWD DOORZHG PED Bit transfer 7.1.1 START and STOP conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line while the clock is HIGH is defined as the START condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP condition (P) (see Figure 8). 6'$ 6&/ 6 3 67$57FRQGLWLRQ 6723FRQGLWLRQ PED Fig 8. Definition of START and STOP conditions 7.2 System configuration A device generating a message is a ‘transmitter’; a device receiving is the ‘receiver’. The device that controls the message is the ‘master’ and the devices which are controlled by the master are the ‘slaves’ (see Figure 9). PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 10 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer SDA SCL MASTER TRANSMITTER/ RECEIVER SLAVE RECEIVER SLAVE TRANSMITTER/ RECEIVER MASTER TRANSMITTER MASTER TRANSMITTER/ RECEIVER I2C-BUS MULTIPLEXER SLAVE 002aaa966 Fig 9. System configuration 7.3 Acknowledge The number of data bytes transferred between the START and the STOP conditions from transmitter to receiver is not limited. Each byte of eight bits is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter, whereas the master generates an extra acknowledge related clock pulse. A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a master must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse; set-up and hold times must be taken into account. A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition. data output by transmitter not acknowledge data output by receiver acknowledge SCL from master 1 2 S START condition 8 9 clock pulse for acknowledgement 002aaa987 Fig 10. Acknowledgement on the I2C-bus PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 11 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 7.4 Bus transactions SCL 1 2 3 4 5 6 7 8 9 slave address 1 SDA S 1 0 data to register command byte 0 A2 A1 A0 0 START condition A R/W 0 0 0 AI B3 B2 B1 B0 A acknowledge from slave DATA 1 A acknowledge from slave acknowledge from slave write to register tv(Q) data out from port DATA 1 VALID 002aae526 Fig 11. Write to register slave address SDA S 1 1 0 command byte 0 A2 A1 A0 0 START condition 0 A 0 1 1 0 AI B3 B2 B1 B0 A R/W 0 A2 A1 A0 1 (repeated) START condition (cont.) acknowledge from slave acknowledge from slave slave address (cont.) S 0 data from register A DATA (first byte) Auto-Increment register address if AI = 1 R/W acknowledge from slave data from register DATA (last byte) A acknowledge from master NA P STOP condition no acknowledge from master at this moment master-transmitter becomes master-receiver and slave-receiver becomes slave-transmitter 002aae527 Fig 12. Read from register no acknowledge from master slave address SDA S 1 1 0 0 A2 A1 A0 1 START condition data from port data from port R/W DATA 1 A A acknowledge from slave DATA 4 acknowledge from master NA P STOP condition read from port tsu(D) th(D) data into port DATA 1 DATA 2 DATA 3 DATA 4 002aae528 Remark: This figure assumes the command byte has previously been programmed with 00h. Fig 13. Read input port register PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 12 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 8. Application design-in information 5V 5V 10 kΩ 10 kΩ 10 kΩ VDD I2C-BUS/SMBus MASTER SDA SDA SCL SCL PCA9532 RESET A2 A1 A0 VSS LED0 LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 LED9 LED10 LED11 LED12 LED13 LED14 LED15 GPIOs 002aae522 LED0 to LED12 are used as LED drivers. LED13 to LED15 are used as regular GPIOs. Fig 14. Typical application 8.1 Minimizing IDD when the I/Os are used to control LEDs When the I/Os are used to control LEDs, they are normally connected to VDD through a resistor as shown in Figure 14. Since the LED acts as a diode, when the LED is off the I/O VI is about 1.2 V less than VDD. The supply current, IDD, increases as VI becomes lower than VDD and is specified as IDD in Table 13 “Static characteristics”. Designs needing to minimize current consumption, such as battery power applications, should consider maintaining the I/O pins greater than or equal to VDD when the LED is off. Figure 15 shows a high value resistor in parallel with the LED. Figure 16 shows VDD less than the LED supply voltage by at least 1.2 V. Both of these methods maintain the I/O VI at or above VDD and prevents additional supply current consumption when the LED is off. PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 13 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 3.3 V VDD VDD LED VDD 100 kΩ LEDn 5V LED LEDn 002aac189 Fig 15. High value resistor in parallel with the LED 002aac190 Fig 16. Device supplied by a lower voltage 8.2 Programming example The following example will show how to set LED0 to LED3 on. It will then set LED4 and LED5 to blink at 1 Hz at a 50 % duty cycle. LED6 and LED7 will be set to be dimmed at 25 % of their maximum brightness (duty cycle = 25 %). LED8 to LED15 will be set to off. Table 11. Programming PCA9532 Program sequence I2C-bus START S PCA9532 address with A0 to A2 = LOW C0h PSC0 subaddress + Auto-Increment 12h Set prescaler PSC0 to achieve a period of 1 second: 97h +1 Blink period = 1 = PSC0 -----------------------152 PSC0 = 151 Set PWM0 duty cycle to 50 %: 80h PWM0 = 0.5 ----------------256 PWM0 = 128 Set prescaler PCS1 to dim at maximum frequency: 00h Blink period = max PSC1 = 0 Set PWM1 output duty cycle to 25 %: 40h PWM1 = 0.25 ----------------256 PWM1 = 64 PCA9532 Product data sheet Set LED0 to LED3 on 55h Set LED4 and LED5 to PWM0, and LED6 or LED7 to PWM1 FAh Set LED8 to LED11 off 00h Set LED12 to LED15 off 00h STOP P All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 14 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 9. Limiting values Table 12. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). PCA9532 Product data sheet Symbol Parameter VDD Conditions Min Max Unit supply voltage 0.5 +6.0 V VI/O voltage on an input/output pin VSS  0.5 5.5 V IO(LEDn) output current on pin LEDn - 25 mA ISS ground supply current - 200 mA Ptot total power dissipation - 400 mW Tstg storage temperature Tamb ambient temperature operating All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 65 +150 C 40 +85 C © NXP Semiconductors N.V. 2016. All rights reserved. 15 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 10. Static characteristics Table 13. Static characteristics VDD = 2.3 V to 5.5 V; VSS = 0 V; Tamb = 40 C to +85 C; unless otherwise specified. Symbol Parameter Conditions Min Typ[1] Max Unit Supplies VDD supply voltage 2.3 - 5.5 V IDD supply current operating mode; VDD = 5.5 V; no load; VI = VDD or VSS; fSCL = 100 kHz - 350 550 A Istb standby current Standby mode; VDD = 5.5 V; no load; VI = VDD or VSS; fSCL = 0 kHz - 2.1 5.0 A IDD additional quiescent supply Standby mode; VDD = 5.5 V; current every LED I/O at VI = 4.3 V; fSCL = 0 kHz - - 2 mA VPOR power-on reset voltage - 1.7 2.2 V VDD = 3.3 V; no load; VI = VDD or VSS [2] Input SCL; input/output SDA VIL LOW-level input voltage 0.5 - +0.3VDD V VIH HIGH-level input voltage 0.7VDD - 5.5 V IOL LOW-level output current VOL = 0.4 V 3 6.5 - mA IL leakage current VI = VDD = VSS 1 - +1 A Ci input capacitance VI = VSS - 4.4 5 pF I/Os VIL LOW-level input voltage 0.5 - +0.8 V VIH HIGH-level input voltage 2.0 - 5.5 V IOL LOW-level output current VOL = 0.4 V VDD = 2.3 V [3] 9 - - mA VDD = 3.0 V [3] 12 - - mA VDD = 5.0 V [3] 15 - - mA VDD = 2.3 V [3] 15 - - mA VDD = 3.0 V [3] 20 - - mA VDD = 5.0 V [3] 25 - - mA 1 - +1 A - 2.6 5 pF VOL = 0.7 V ILI input leakage current Cio input/output capacitance VDD = 3.6 V; VI = 0 V or VDD Select inputs A0, A1, A2; RESET VIL LOW-level input voltage 0.5 - +0.8 V VIH HIGH-level input voltage 2.0 - 5.5 V ILI input leakage current 1 - +1 A Ci input capacitance - 2.3 5 pF VI = VSS [1] Typical limits at VDD = 3.3 V, Tamb = 25 C. [2] VDD must be lowered to 0.2 V in order to reset part. [3] Each I/O must be externally limited to a maximum of 25 mA and each octal ([LED0 to LED7] and [LED8 to LED15]) must be limited to a maximum current of 100 mA for a device total of 200 mA. PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 16 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 20 % 002aac191 (1) percent variation 20 % 002aac192 (1) percent variation 0% 0% (2) −20 % (3) (2) −20 % (3) −40 % −40 −20 0 20 40 60 80 100 Tamb (°C) −40 % −40 −20 (1) maximum (1) maximum (2) average (2) average (3) minimum (3) minimum Fig 17. Typical frequency variation over process at VDD = 2.3 V to 3.0 V PCA9532 Product data sheet 0 20 40 60 80 100 Tamb (°C) Fig 18. Typical frequency variation over process at VDD = 3.0 V to 5.5 V All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 17 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 11. Dynamic characteristics Table 14. Dynamic characteristics Symbol Parameter Conditions Standard-mode I2C-bus Min Max Fast-mode I2C-bus Min Max Unit fSCL SCL clock frequency 0 100 0 400 tBUF bus free time between a STOP and START condition 4.7 - 1.3 - s tHD;STA hold time (repeated) START condition 4.0 - 0.6 - s tSU;STA set-up time for a repeated START condition 4.7 - 0.6 - s tSU;STO set-up time for STOP condition 4.0 - 0.6 - s tHD;DAT data hold time tVD;ACK data valid acknowledge time tVD;DAT data valid time kHz 0 - 0 - ns [1] - 600 - 600 ns LOW-level [2] - 600 - 600 ns HIGH-level [2] - 1500 - 600 ns tSU;DAT data set-up time 250 - 100 - ns tLOW LOW period of the SCL clock 4.7 - 1.3 - s tHIGH HIGH period of the SCL clock 4.0 - 0.6 - s 20 + 0.1Cb[3] 300 ns 20 + 0.1Cb[3] 300 ns rise time of both SDA and SCL signals tr - 1000 tf fall time of both SDA and SCL signals - 300 tSP pulse width of spikes that must be suppressed by the input filter - 50 - 50 ns tv(Q) data output valid time - 200 - 200 ns tsu(D) data input set-up time 100 - 100 - ns th(D) data input hold time 1 - 1 - s tw(rst) reset pulse width 10 - 10 - ns trec(rst) reset recovery time trst reset time Port timing Reset [4][5] [1] tVD;ACK = time for Acknowledgement signal from SCL LOW to SDA (out) LOW. [2] tVD;DAT = minimum time for SDA data output to be valid following SCL LOW. 0 - 0 - ns 400 - 400 - ns [3] Cb = total capacitance of one bus line in pF. [4] Resetting the device while actively communicating on the bus may cause glitches or errant STOP conditions. [5] Upon reset, the full delay will be the sum of trst and the RC time constant of the SDA bus. PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 18 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer ACK or read cycle START SCL SDA 30 % trst RESET 50 % 50 % trec(rst) 50 % tw(rst) trst LEDn 50 % LED off 002aac193 Fig 19. Definition of RESET timing 0.7 × VDD SDA 0.3 × VDD tr tBUF tf tHD;STA tSP tLOW 0.7 × VDD SCL 0.3 × VDD tHD;STA P tSU;STA tHD;DAT S tHIGH tSU;DAT tSU;STO Sr P 002aaa986 Fig 20. Definition of timing protocol START condition (S) tSU;STA bit 7 MSB (A7) tLOW bit 6 (A6) tHIGH bit 0 (R/W) acknowledge (A) STOP condition (P) 1 / fSCL 0.7 × VDD SCL 0.3 × VDD tBUF tr tf 0.7 × VDD SDA 0.3 × VDD tSU;DAT tHD;STA tHD;DAT tVD;DAT tVD;ACK tSU;STO 002aab175 Rise and fall times refer to VIL and VIH. Fig 21. I2C-bus timing diagram PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 19 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 12. Test information VDD PULSE GENERATOR VI VO RL 500 Ω VDD open VSS DUT RT CL 50 pF 002aab880 RL = load resistor for LEDn. RL for SDA and SCL > 1 k (3 mA or less current). CL = load capacitance includes jig and probe capacitance. RT = termination resistance should be equal to the output impedance Zo of the pulse generators. Fig 22. Test circuitry for switching times PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 20 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 13. Package outline 62SODVWLFVPDOORXWOLQHSDFNDJHOHDGVERG\ZLGWKPP 627 ' ( $ ; F +( \ Y 0 $ =   4 $ $ $  $ SLQLQGH[ ș /S /   H ES GHWDLO; Z 0   PP VFDOH ',0(16,216LQFKGLPHQVLRQVDUHGHULYHGIURPWKHRULJLQDOPPGLPHQVLRQV 81,7 $ PD[ $ $ $ ES F ' ( H +( / /S 4 Y Z \ PP                                                    LQFKHV   =   ș R R 1RWH 3ODVWLFRUPHWDOSURWUXVLRQVRIPPLQFKPD[LPXPSHUVLGHDUHQRWLQFOXGHG 5()(5(1&(6 287/,1( 9(56,21 ,(& -('(& 627 ( 06 -(,7$ (8523($1 352-(&7,21 ,668('$7(   Fig 23. Package outline SOT137-1 (SO24) PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 21 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 76623SODVWLFWKLQVKULQNVPDOORXWOLQHSDFNDJHOHDGVERG\ZLGWKPP ' 627 ( $ ; F +( \ Y 0 $ =   4 $ SLQLQGH[ $  $ $ ș /S /   ES H GHWDLO; Z 0   PP VFDOH ',0(16,216PPDUHWKHRULJLQDOGLPHQVLRQV 81,7 $ PD[ $ $ $ ES F ' ( H +( / /S 4 Y Z \ = ș PP                            R R 1RWHV 3ODVWLFRUPHWDOSURWUXVLRQVRIPPPD[LPXPSHUVLGHDUHQRWLQFOXGHG 3ODVWLFLQWHUOHDGSURWUXVLRQVRIPPPD[LPXPSHUVLGHDUHQRWLQFOXGHG 287/,1( 9(56,21 627 5()(5(1&(6 ,(& -('(& -(,7$ (8523($1 352-(&7,21 ,668('$7(   02 Fig 24. Package outline SOT355-1 (TSSOP24) PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 22 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer +94)1SODVWLFWKHUPDOHQKDQFHGYHU\WKLQTXDGIODWSDFNDJHQROHDGV WHUPLQDOVERG\[[PP % ' 627 $ WHUPLQDO LQGH[DUHD $ $ ( F GHWDLO; H & H H  \ & Y 0 & $ % Z 0 & E  \ /   H H (K H  WHUPLQDO LQGH[DUHD    ; 'K   PP VFDOH ',0(16,216PPDUHWKHRULJLQDOGLPHQVLRQV $ 81,7 $ F E 'K ' PD[ PP           ( (K H H H / Y Z \ \              1RWH 3ODVWLFRUPHWDOSURWUXVLRQVRIPPPD[LPXPSHUVLGHDUHQRWLQFOXGHG 5()(5(1&(6 287/,1( 9(56,21 ,(& -('(& -(,7$ 627  02  (8523($1 352-(&7,21 ,668('$7(    Fig 25. Package outline SOT616-1 (HVQFN24) PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 23 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 14. Handling information All input and output pins are protected against ElectroStatic Discharge (ESD) under normal handling. When handling ensure that the appropriate precautions are taken as described in JESD625-A or equivalent standards. 15. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 15.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 15.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 15.3 Wave soldering Key characteristics in wave soldering are: PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 24 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities 15.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 26) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 15 and 16 Table 15. SnPb eutectic process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350  350 < 2.5 235 220  2.5 220 220 Table 16. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 26. PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 25 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 26. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 16. Abbreviations Table 17. PCA9532 Product data sheet Abbreviations Acronym Description ACPI Advanced Configuration and Power Interface CDM Charged Device Model DSP Digital Signal Processor DUT Device Under Test ESD ElectroStatic Discharge GPIO General Purpose Input/Output HBM Human Body Model I2C-bus Inter-Integrated Circuit bus LED Light Emitting Diode MCU MicroController Unit MM Machine Model MPU MicroProcessor Unit POR Power-On Reset RC Resistor-Capacitor network SMBus System Management Bus All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 26 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 17. Revision history Table 18. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA9532 v.4.1 20160822 Product data sheet - PCA9532_4 Modifications: PCA9532_4 Modifications: • Table 1: Corrected topside mark for PCA9532PW. 20090317 Product data sheet - PCA9532_3 • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. • • Legal texts have been adapted to the new company name where appropriate. • • Table 2 “Pin description”: added Table note [1] and its reference at HVQFN24 pin 9, VSS Section 5.1 “Pinning”: replaced (old) Figure 1 with separate drawings for SO24 (Figure 2) and TSSOP24 (Figure 3) Section 6.2 “Control register”: – 2nd paragraph: changed from “The lowest 3 bits are ...” to “The lowest 4 bits are ...” – 4th paragraph: changed from “... by reading a register different from ‘0’ ...” to “... by reading a register different from INPUT0 ...” • • • Section 6.6 “External RESET”, 1st paragraph, 1st sentence: changed symbol from “tW” to “tw(rst)” Figure 11 “Write to register”: symbol changed from “tpv” to “tv(Q)” Figure 13 “Read input port register”: – Symbol changed from “tph” to “th(D)” – Symbol changed from “tps” to “tsu(D)” • Table 12 “Limiting values”: changed symbol/parameter from “II/O, DC output current on an I/O” to “IO(LEDn), output current on pin LEDn” • Table 13 “Static characteristics”: – Descriptive line below table title: 2nd sentence is moved to Table note [1], with its reference at column heading “Typ” – IDD parameter changed from “additional standby current” to “additional quiescent supply current” – Sub-section “I/Os”: symbol changed from “IL” to “ILI” • Table 14 “Dynamic characteristics”: – Symbol/parameter changed from “tPV, Output data valid” to “tv(Q), data output valid time” – Symbol/parameter changed from “tPS, Input data set-up time” to “tsu(D), data input set-up time” – Symbol/parameter changed from “tPH, Input data hold time” to “th(D), data input hold time” – Symbol changed from “tW” to “tw(rst)” – Symbol changed from “tREC” to “trec(rst)” – Symbol/parameter changed from “tRESET, Time to reset” to “trst, reset time” • Figure 19 “Definition of RESET timing”: – Symbol changed from “tREC” to “trec(rst)” – Symbol changed from “tRESET” to “trst” – Symbol changed from “tW” to “tw(rst)” – Symbol changed from “tRESET” to “trst” • • Updated handling information Added soldering information PCA9532_3 20041001 Product data sheet - PCA9532_2 PCA9532_2 (9397 750 11459) 20030502 Product data ECN 853-2398 29860 dated 24 Apr 2003 PCA9532_1 PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 27 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer Table 18. Revision history …continued Document ID Release date Data sheet status Change notice Supersedes PCA9532_1 (9397 750 10874) 20030226 Product data ECN 853-2398 29297 dated 12 Dec 2002 - PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 28 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 18. Legal information 18.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 18.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. PCA9532 Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 29 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 18.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP Semiconductors N.V. 19. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com PCA9532 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4.1 — 22 August 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 30 of 31 PCA9532 NXP Semiconductors 16-bit I2C-bus LED dimmer 20. Contents 1 2 3 4 5 5.1 5.2 6 6.1 6.2 6.2.1 6.3 6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.3.6 6.3.7 6.4 6.5 6.6 7 7.1 7.1.1 7.2 7.3 7.4 8 8.1 8.2 9 10 11 12 13 14 15 15.1 15.2 15.3 15.4 16 17 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Device address . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control register . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control register definition . . . . . . . . . . . . . . . . . 6 Register descriptions . . . . . . . . . . . . . . . . . . . . 6 INPUT0 - Input register 0 . . . . . . . . . . . . . . . . . 6 INPUT1 - Input register 1 . . . . . . . . . . . . . . . . . 6 PCS0 - Frequency Prescaler 0 . . . . . . . . . . . . . 7 PWM0 - Pulse Width Modulation 0 . . . . . . . . . . 7 PCS1 - Frequency Prescaler 1 . . . . . . . . . . . . . 7 PWM1 - Pulse Width Modulation 1 . . . . . . . . . . 7 LS0 to LS3 - LED selector registers . . . . . . . . . 8 Pins used as GPIOs . . . . . . . . . . . . . . . . . . . . . 9 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . 9 External RESET . . . . . . . . . . . . . . . . . . . . . . . . 9 Characteristics of the I2C-bus . . . . . . . . . . . . 10 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 START and STOP conditions . . . . . . . . . . . . . 10 System configuration . . . . . . . . . . . . . . . . . . . 10 Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . 11 Bus transactions . . . . . . . . . . . . . . . . . . . . . . . 12 Application design-in information . . . . . . . . . 13 Minimizing IDD when the I/Os are used to control LEDs . . . . . . . . . . . . . . . . . . . . . . . . 13 Programming example . . . . . . . . . . . . . . . . . . 14 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 15 Static characteristics. . . . . . . . . . . . . . . . . . . . 16 Dynamic characteristics . . . . . . . . . . . . . . . . . 18 Test information . . . . . . . . . . . . . . . . . . . . . . . . 20 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 21 Handling information. . . . . . . . . . . . . . . . . . . . 24 Soldering of SMD packages . . . . . . . . . . . . . . 24 Introduction to soldering . . . . . . . . . . . . . . . . . 24 Wave and reflow soldering . . . . . . . . . . . . . . . 24 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 24 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 25 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 27 18 18.1 18.2 18.3 18.4 19 20 Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 29 29 29 30 30 31 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP Semiconductors N.V. 2016. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 22 August 2016 Document identifier: PCA9532