PCA9558PW,112

PCA9558 8-bit I2C-bus and SMBus I/O port with 5-bit multiplexed/1-bit latched 6-bit I2C-bus EEPROM DIP switch and 2-kbit EEPROM Rev. 5 — 25 June 2012 Product data sheet 1. General description The PCA9558 is a highly integrated, multi-function device that is composed of a 5-bit multiplexed/1-bit latched 6-bit I2C-bus/SMBus EEPROM DIP switch, an 8-bit I/O expander and a 2-kbit serial EEPROM with write protect. The PCA9558 integrates these commonly used components into a single chip to reduce component count and board space requirements and is useful in computer, server and telecom/networking applications. • Multiplexed/latched EEPROM DIP switch — used to select digital information between a set of 5 bits of default hardware inputs and an alternative set of inputs provided by the I2C-bus/SMBus interface and stored in the EEPROM. Examples of this type of selection include processor voltage configuration or processor vendor identification (VID). The multiplexed/latched EEPROM can also be used to replace DIP switches or jumpers, since the settings can be easily changed via I2C-bus/SMBus without having to power down the equipment to open the cabinet. The non-volatile memory retains the most current setting selected before the power is turned off. • 8-bit I/O expander — used to control, monitor or collect remote information or power LEDs. Monitored or collected information can be read through the I2C-bus/SMBus or can be stored in the internal EEPROM. • 2-kbit serial EEPROM — used to store information such as card identification or revision/maintenance history on every motherboard/line card and can be read or written via I2C-bus/SMBus when required. The PCA9558 has one address pin, allowing up to two devices to be placed on the same I2C-bus or SMBus. 2. Features and benefits  5-bit 2-to-1 multiplexer, 1-bit latch DIP switch  6-bit MUX_OUTx and NON_MUXED_OUT EEPROM programmable and readable via I2C-bus  5 V tolerant open-drain MUX_OUTx and NON_MUXED_OUT outputs  Active LOW override input forces all MUX_OUTx outputs to logic 0  I2C-bus readable MUX_INx inputs  5 V tolerant open-drain IOx pins, power-up default as outputs  One address pin, allowing up to two devices on the I2C-bus  Active LOW reset input with internal pull-up for the eight I/O pins  2048-bit EEPROM programmable and readable via the I2C-bus or I/Os  Operating power supply voltage range of 3.0 V to 3.6 V  SMBus compliance with fixed 3.3 V levels PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port  2.5 V to 5 V tolerant inputs  ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101  Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA 3. Applications      Board version tracking and configuration Board health monitoring and status reporting Multi-card systems in telecom, networking and base station infrastructure equipment Field recall and troubleshooting functions for installed boards General-purpose integrated I/O with DIP switch and memory 4. Ordering information Table 1. Ordering information Type number PCA9558PW PCA9558 Product data sheet Topside mark PCA9558DH Temperature range Package Name Description Version 0 °C to 70 °C TSSOP28 plastic thin shrink small outline package; 28 leads; body width 4.4 mm SOT361-1 All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 2 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 5. Block diagram PCA9558 MUX_SELECT MUX_OUT_LOW 6-bit EEPROM LATCH NMO NON_MUXED_OUT 5 MUX_INA to MUX_INE 1 MUX_OUTA MUX_OUTB 5-BIT 2 TO 1 MUX A0 SCL SDA I2C-BUS INTERFACE LOGIC MUX_OUTD INPUT FILTER MUX_OUTE 0 5 VDD MUX_OUTC I2C-BUS CONTROL LOGIC POWER-ON RESET VSS 8 WP 256-BYTE EEPROM GPIO IO0 to IO7 IO_OUT_LOW 002aad366 Fig 1. Block diagram of PCA9558 PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 3 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 6. Pinning information 6.1 Pinning SCL 1 28 VDD SDA 2 27 WP IO_OUT_LOW 3 26 MUX_OUT_LOW A0 4 25 NON_MUXED_OUT MUX_INA 5 24 MUX_OUTA MUX_INB 6 23 MUX_OUTB MUX_INC 7 MUX_IND 8 MUX_INE 9 PCA9558PW 22 MUX_OUTC 21 MUX_OUTD 20 MUX_OUTE VSS 10 19 MUX_SELECT IO0 11 18 IO7 IO1 12 17 IO6 IO2 13 16 IO5 IO3 14 15 IO4 002aad365 Fig 2. Pin configuration for TSSOP28 6.2 Pin description Table 2. PCA9558 Product data sheet Pin description Symbol Pin Description SCL 1 serial I2C-bus clock SDA 2 serial bidirectional I2C-bus data IO_OUT_LOW 3 active LOW control forces all GPIO to logic 0 outputs A0 4 A0 address MUX_INA 5 external input A to multiplexer MUX_INB 6 external input B to multiplexer MUX_INC 7 external input C to multiplexer MUX_IND 8 external input D to multiplexer MUX_INE 9 external input E to multiplexer VSS 10 ground IO0 11 general purpose input/output 0 (open-drain output) IO1 12 general purpose input/output 1 (open-drain output) IO2 13 general purpose input/output 2 (open-drain output) IO3 14 general purpose input/output 3 (open-drain output) IO4 15 general purpose input/output 4 (open-drain output) IO5 16 general purpose input/output 5 (open-drain output) IO6 17 general purpose input/output 6 (open-drain output) IO7 18 general purpose input/output 7 (open-drain output) All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 4 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port Table 2. Pin description …continued Symbol Pin Description MUX_SELECT 19 active LOW select of MUX_INx inputs or EEPROM contents for MUX_OUTx outputs MUX_OUTE 20 open-drain multiplexed output E MUX_OUTD 21 open-drain multiplexed output D MUX_OUTC 22 open-drain multiplexed output C MUX_OUTB 23 open-drain multiplexed output B MUX_OUTA 24 open-drain multiplexed output A NON_MUXED_OUT 25 open-drain outputs from non-volatile memory MUX_OUT_LOW 26 active LOW control forces all MUX outputs to logic 0 WP 27 active HIGH EEPROM write protect VDD 28 power supply (3.0 V to 3.6 V) 7. Functional description Refer to Figure 1 “Block diagram of PCA9558”. 7.1 I2C-bus interface Communicating with this device is initiated by sending a valid address on the I2C-bus. The address format (see Figure 3) has 6 fixed bits and one user-programmable bit followed by a 1-bit read/write value which determines the direction of the data transfer. MSB 1 LSB 0 0 1 1 1 fixed A0 R/W hardware selectable 002aad367 Fig 3. I2C-bus address byte Following the address and acknowledge bit are 8 data bits which, depending on the read/write bit in the address, will read data from or write data to the EEPROM. Data will be written to the register if the read/write bit is logic 0 and the WP input is logic 0. Data will be read from the register if the bit is logic 1. The four high-order bits are latched outputs, while the four low order bits are multiplexed outputs (Figure 5). Remark: To ensure data integrity, the EEPROM must be internally write protected when VDD to the I2C-bus is powered down or VDD to the component is dropped below normal operating levels. D7 D6 D5 D4 D3 D2 D1 D0 002aad368 Fig 4. PCA9558 Product data sheet Command byte All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 5 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port Table 3. Command byte D7 D6 D5 D4 D3 D2 D1 D0 Command 0 0 0 0 0 0 0 1 write to 256-byte EEPROM via I2C-bus 0 0 0 0 0 0 1 1 read from 256-byte EEPROM via I2C-bus 0 0 0 0 0 1 0 0 write to 6-bit EEPROM via I2C-bus 0 0 0 0 0 1 1 0 read from 6-bit EEPROM via I2C-bus 0 0 0 0 0 1 1 1 read Input Port (IP) register via I2C-bus 0 0 0 0 1 0 0 0 read/write Output Port (OP) register via I2C-bus 0 0 0 0 1 0 0 1 read/write Polarity Inversion (PI) register via I2C-bus 0 0 0 0 1 0 1 0 read/write Input/Output Configuration (IOC) register via I2C-bus 0 0 0 0 1 0 1 1 read/write MUX Control (MUXCNTRL) register via I2C-bus 0 0 0 0 1 1 0 0 read MUX_INx values via I2C-bus 0 0 0 0 1 1 0 1 reserved 0 0 0 0 1 1 1 0 reserved 0 0 0 0 1 1 1 1 read 256-byte EEPROM and write OP register 0 0 0 1 0 0 0 0 read 256-byte EEPROM and write PI register 0 0 0 1 0 0 0 1 read 256-byte EEPROM and write IOC register 0 0 0 1 0 0 1 0 read IP register and write to 256-byte EEPROM 0 0 0 1 0 0 1 1 reserved : : : : : : : : 1 1 1 1 1 1 1 1 reserved 7.1.1 Multiplexer MSB 0 LSB 0 NONMUX MUX MUX MUX MUX MUXED DATA E DATA D DATA C DATA B DATA A DATA 002aad369 Fig 5. I2C-bus MUX_OUTx data byte MSB 0 LSB 0 0 MUX_IN MUX_IN MUX_IN MUX_IN MUX_IN D B A E C 002aad370 Fig 6. PCA9558 Product data sheet I2C-bus MUX_INx data byte All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 6 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port The Multiplexer function controls the six open-drain outputs, MUX_OUTx and NON_MUXED_OUT. This control is affected by the input pins MUX_SELECT (pin 19), MUX_OUT_LOW (pin 26), and/or an internal register programmed via the I2C-bus. Upon power-up, the multiplex function is controlled by the MUX_SELECT and MUX_OUT_LOW pins. When the MUX_SELECT signal is a logic 0, the multiplexer will select the data from the 6-bit EEPROM to drive on the MUX_OUTx and NON_MUXED_OUT pins. When the MUX_SELECT signal is a logic 1, the multiplexer will select the MUX_INx pins to drive on the MUX_OUTx pins. The NON_MUXED_OUT output is latched from the 6-bit EEPROM on a rising edge of the MUX_SELECT signal. This latch is transparent while the MUX_SELECT signal is a logic 0. An internal control register, written via the I2C-bus, can also control the multiplexer function. When this register is written, the MUX_SELECT function can change from the external pin to an internal register. In this register a bit will act in a similar fashion to the MUX_SELECT input, i.e., a logic 1 will cause the multiplexer to select data from the 6-bit EEPROM to drive on the MUX_OUTx and NON_MUXED_OUT pins. In this configuration, the NON_MUXED_OUT will latch data when the PCA9558 acknowledges the I2C-bus. The MUX_SELECT pin will have no effect on the MUX_OUTx or NON_MUXED_OUT while in this mode. When the MUX_OUT_LOW signal is a logic 0 and the multiplexer is configured so that the MUX_OUTx pins are being driven by the 6-bit EEPROM, the MUX_OUTx pins will be driven to a logic 0. This information is summarized in Table 4. Table 4. Multiplexer function table Register Input Output B1[1] B0[1] MUX_OUT_LOW MUX_SELECT MUX_OUTx NON_MUXED_OUT x 0 0 MUX_INx inputs latched from EEPROM[2] 1 x 0 0 0 0 0 x 0 1 1 MUX_INx inputs latched from EEPROM[2] x 0 1 0 from EEPROM from EEPROM 0 1 0 x MUX_INx inputs latched from EEPROM[3] 1 1 0 x 0 0 0 1 1 x MUX_INx inputs latched from EEPROM[3] 1 1 1 x from EEPROM from EEPROM [1] These are the 2 LSBs of the MUX Control (MUXCNTRL) register. [2] NON_MUXED_OUT value will be the value present in the 6-bit EEPROM at the time of the rising edge of the MUX_SELECT input. [3] NON_MUXED_OUT value will be the value present in the 6-bit EEPROM at the time of the slave ACK when bit 1 has changed from logic 0 to logic 1. If the MUX_OUTx outputs are being driven by the 6-bit EEPROM and this EEPROM is programmed, the outputs will remain stable and change to the new values after the EEPROM program cycle completes. Examples of read/write for MUX control can be found in Figure 7. PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 7 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port slave address S 1 0 0 1 1 command byte 1 A0 0 START condition A R/W 0 0 0 0 1 data byte 0 acknowledge from slave 1 1 A 0 0 0 0 0 acknowledge from slave 0 B1 B0 A P acknowledge from slave STOP condition 002aad371 Fig 7. I2C-bus write for MUXCNTRL register slave address S 1 0 0 1 1 command byte 1 A0 0 START condition R/W A 0 0 0 acknowledge from slave 0 1 0 slave address 1 1 A acknowledge from slave S 1 0 0 1 1 1 A0 1 (re)START condition R/W A (cont.) acknowledge from slave data from slave (cont.) 0 0 0 0 0 0 B1 B0 NA P no acknowledge from master STOP condition 002aad372 Fig 8. I2C-bus read for MUXCNTRL register 7.1.2 Registers The GPIOs are controlled by a set of 4 internal registers: Input Port (IP) register; Output Port (OP) register; Polarity Inversion (PI) register; and the Input/Output Configuration (IOC) register. Each register is read/write via the I2C-bus or 256-byte EEPROM, with the exception of the Input Port register, which is read only, one at a time. The read/write takes place on the slave Acknowledge. The control of which register is currently available to the I2C-bus is set by bits in the control register. See Section 7.1.2.1 through Section 7.1.2.4 for details. 7.1.2.1 IP - Input Port register This register is an input-only port. It reflects the logic value present on the GPIO pins regardless of whether they are configured as inputs or outputs (IOC register). Writes to this register have no effect. Table 5. PCA9558 Product data sheet IP - Input Port register description Bit 7 6 5 4 3 2 1 0 Symbol I7 I6 I5 I4 I3 I2 I1 I0 Default 0 0 0 0 0 0 0 0 All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 8 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 7.1.2.2 OP - Output Port register This register is an output-only port. It reflects the outgoing logic levels of the GPIO defined as outputs in the IOC register. Bit values in this register have no effect on GPIO defined as inputs. In turn, reads from this register reflect the value stored in the flip-flop controlling the output, not the actual output value. Table 6. Bit 7.1.2.3 OP - Output Port register description 7 6 5 4 3 2 1 0 Symbol O7 O6 O5 O4 O3 O2 O1 O0 Default 0 0 0 0 0 0 0 0 PI - Polarity Inversion register This register enables polarity inversion of GPIO defined as inputs by the IOC register. If a bit in this register is set to a logic 1, the corresponding GPIO input port is inverted. If a bit in this register is set to a logic 0, the corresponding GPIO input port is not inverted. Table 7. Bit 7.1.2.4 PI - Polarity Inversion register description 7 6 5 4 3 2 1 0 Symbol P7 P6 P5 P4 P3 P2 P1 P0 Default 1 1 1 1 0 0 0 0 IOC - Input/Output Configuration register This register configures the direction of the GPIO pins (IOx). If a bit is set to a logic 1, the corresponding port pin is enabled as an input with a high-impedance output driver. If a bit is set to a logic 0, the corresponding port pin is enabled as an output. Table 8. Bit IOC - Input/Output Configuration register description 7 6 5 4 3 2 1 0 Symbol C7 C6 C5 C4 C3 C2 C1 C0 Default 0 0 0 0 0 0 0 0 Examples of read/write to these registers can be found in Figure 9, Figure 10, Figure 15, and Figure 16. The IO_OUT_LOW input, when held LOW longer than the time Tcy(W), will reset the GPIO registers to their default (power-up) values. A read of the present value of the inputs MUX_INx can be done via the I2C-bus. This is done by addressing the PCA9558 in a write mode and entering the correct command code. The preset value on the MUX_INx inputs is latched at the command code Acknowledge. A REPEATED START is then sent with the R/W bit set to a logic 1, read, and this latched data is read out on the I2C-bus. See Figure 11. PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 9 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port slave address S 1 0 0 1 1 START condition command byte 1 A0 0 A R/W 0 0 0 0 x data byte x acknowledge from slave x x A d7 d6 d5 d4 d3 d2 d1 d0 A acknowledge from slave P STOP condition acknowledge from slave 002aad373 See Table 3 for the proper command byte. Fig 9. I2C-bus write for GPIO registers slave address S 1 0 0 1 1 START condition command byte 1 A0 0 R/W A 0 0 0 0 x acknowledge from slave x slave address x x A acknowledge from slave S 1 0 0 1 1 1 A0 1 (re)START condition R/W A (cont.) acknowledge from slave data from slave (cont.) d7 d6 d5 d4 d3 d2 d1 d0 NA P no acknowledge from master STOP condition 002aad374 Fig 10. I2C-bus read for GPIO registers slave address S 1 0 0 1 START condition 1 command byte 1 A0 0 R/W A 0 0 0 acknowledge from slave 0 1 1 slave address 0 0 A acknowledge from slave S 1 0 0 1 1 1 A0 1 (re)START condition R/W A (cont.) acknowledge from slave data from slave (cont.) 0 0 0 d4 d3 d2 d1 d0 NA P no acknowledge from master STOP condition 002aad375 Fig 11. I2C-bus read of MUX_INx inputs PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 10 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 7.1.3 EEPROM write operation 7.1.3.1 6-bit write operation A write operation to the 6-bit EEPROM requires that an address byte be written after the command byte. This address points to the 6-bit address space in the EEPROM array. Upon receipt of this address, the PCA9558 waits for the next byte that will be written to the EEPROM. The master then ends the transaction with a STOP condition on the I2C-bus. See Figure 12. After the STOP condition, the E/W cycle starts, and the parts will not respond to any request to access the EEPROM array until the cycle finishes, approximately 4 ms. slave address S 1 0 0 1 1 EEPROM address command byte 1 A0 0 START condition R/W A 0 0 0 0 0 acknowledge from slave 1 0 0 A 1 1 1 1 1 1 1 1 acknowledge from slave A (cont.) acknowledge from slave data for 6-bit EEPROM (cont.) X X d5 d4 d3 d2 d1 d0 A acknowledge from slave P programming begins after STOP STOP condition 002aad376 Fig 12. I2C-bus write of 6-bit EEPROM 7.1.3.2 6-bit read operation A read operation is initiated in the same manner as a write operation, with the exception that after the word address has been written a REPEATED START condition is placed on the I2C-bus and the direction of communication is reversed (see Figure 13). slave address S 1 0 0 1 START condition 1 EEPROM address command byte 1 A0 0 A R/W 0 0 0 0 0 acknowledge from slave 1 1 0 A 1 S 1 0 0 (re)START condition 1 acknowledge from slave 1 1 1 1 1 1 1 A (cont.) acknowledge from slave slave address (cont.) 1 data from 6-bit EEPROM 1 A0 1 R/W A 0 0 d5 d4 d3 d2 d1 d0 NA P acknowledge from slave no acknowledge from master STOP condition 002aad377 Fig 13. I2C-bus read of 6-bit EEPROM PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 11 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 7.1.3.3 256-byte write operation (I2C-bus) A write operation to the 256-byte EEPROM requires that an address byte be written after the command byte. This address points to the starting address in the EEPROM array. The four LSBs of this address select a position on a 16-byte page register, the four MSBs select which page register. The four LSBs will be auto-incremented after receipt of each byte of data; in this manner, the entire page register can be written starting at any point. Up to 16 bytes of data may be sent to the PCA9558, followed by a STOP condition on the I2C-bus. If the master sends more than 16 bytes of data prior to generating a STOP condition, data within the address page will be overwritten and unpredictable results may occur. See Figure 14. After the STOP condition, the E/W cycle starts, and the parts will not respond to any request to access the EEPROM array until the cycle finishes, approximately 4 ms. slave address S 1 0 0 1 START condition 1 acknowledge from slave command code 1 A0 0 R/W A 0 0 0 0 0 0 0 1 A acknowledge from slave EEPROM address A acknowledge from slave acknowledge from slave A (cont.) DATA N Auto-Increment word address acknowledge from slave (cont.) DATA N + 1 A Auto-Increment word address acknowledge from slave DATA N + M A Auto-Increment word address P STOP condition 002aad378 M bytes where M ≤ 15. Fig 14. I2C-bus page write operation to 256-byte EEPROM PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 12 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 256-byte read operation (I2C-bus) 7.1.3.4 A read operation is initiated in the same manner as a write operation, with the exception that after the word address has been written, a REPEATED START condition is placed on the I2C-bus, and the direction of communication is reversed. For a read operation, the entire address is incremented after the transmission of each byte, meaning that the entire 256-byte EEPROM array can be read at one time. See Figure 15. slave address S 1 0 0 1 1 1 A0 0 START condition S 1 0 0 A 0 0 0 0 0 0 1 1 A acknowledge from slave A (cont.) EEPROM address R/W slave address (cont.) acknowledge from slave acknowledge from slave command code 1 1 acknowledge from slave 1 A0 1 (re)START condition acknowledge from master A DATA N A DATA N + M Auto-Increment word address R/W no acknowledge from master NA P STOP condition Auto-Increment word address 002aad379 M bytes where M ≥ 1. Fig 15. I2C-bus read operation from 256-byte EEPROM 7.1.3.5 256-byte EEPROM write to GPIO A mode is available whereby a byte of data in the 256-byte EEPROM array can be written to the GPIO (OP register). This is initiated by the I2C-bus. In this mode, a control word indicating a read from the 256-byte EEPROM and write to the GPIO is sent, followed by the word address of the data within the EEPROM array. Upon Acknowledge from the slave, the data is sent to the GPIO. See Figure 16. slave address S 1 0 0 1 START condition 1 EEPROM address command byte 1 A0 0 R/W A 0 0 0 x x acknowledge from slave x x x A a7 a6 a5 a4 a3 a2 a1 a0 A (cont.) acknowledge from slave slave address (cont.) S 1 0 (re)START condition 0 1 1 acknowledge from slave data from 256-byte EEPROM 1 A0 1 R/W A d7 d6 d5 d4 d3 d2 d1 d0 NA P acknowledge from slave no acknowledge from master STOP condition; data latched into GPIO register 002aad380 See Table 3 for the needed command code. Fig 16. Read from 256-byte EEPROM and write to GPIO registers PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 13 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 7.1.3.6 256-byte EEPROM write from GPIO A mode is available whereby data in the GPIO (IP register) can be written to the 256-byte EEPROM. This is initiated by the I2C-bus. In this mode, a control word indicating a read from the GPIO and write to the 256-byte EEPROM is sent, followed by the word address for the data to be written. Once the slave has sent an Acknowledge, the master must send a STOP condition. See Figure 17. After the STOP condition, the E/W cycle starts, and the parts will not respond to any request to access the EEPROM array until the cycle finishes, approximately 4 ms. When the Write Protect (WP) input is a logic 0 it allows writes to both EEPROM arrays. When it is a logic 1, it prevents any writes to the EEPROM arrays. GPIO input port data latched slave address S 1 0 0 1 1 START condition EEPROM address dummy byte A a7 a6 a5 a4 a3 a2 a1 a0 A x x x x x x x x command byte 1 A0 0 R/W A 0 0 0 1 acknowledge from slave 0 0 1 0 acknowledge from slave acknowledge from slave A P acknowledge from slave STOP condition; programming begins after STOP 002aad381 See Table 3 for the needed command code. Fig 17. Read from GPIO Input Port register and write to 256-byte EEPROM 7.1.4 Reset 7.1.4.1 Power-on reset When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9558 in a reset state until VDD has reached VPOR. At that point, the reset condition is released and the PCA9558 volatile registers and SMBus state machine will initialize to their default states. The GPIO outputs (IOx) will be selected as outputs. The DIP switch MUX_OUTx and NON_MUXED_OUT pin values depend on: • The MUX_OUT_LOW and MUX_SELECT logic levels • The previously stored values in the EEPROM register/current MUX_INx pin values as shown in Table 4 7.1.4.2 External reset A reset of the GPIO registers can be accomplished by holding the IO_OUT_LOW pin LOW for a minimum of Tcy(W). These GPIO registers return to their default states until the IO_OUT_LOW input is once again HIGH. PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 14 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 7.2 Using the PCA9558 on the SMBus It is possible to use Intel chip sets to communicate with the PCA9558. There are no limitations when the SMBus controller is communicating with the MUX or the GPIO; however, there are limitations with the 2-kbit serial EEPROM. Because of being able to address any location in the EEPROM block using the second command byte, the designer using the PCA9558 on the SMBus will have to program around it, an easy thing to do. The device designers had to deal with the specifics of addressing the EEPROM and chose the I2C-bus specification and use the second command byte to address any location in the EEPROM block. In order to write to the EEPROM, write the EEPROM address byte in the Data0 byte and the data to be sent should be placed in the Data1 byte. The Intel chip set’s Word Data instruction would then send the address, followed by the command register then Data0 (EEPROM address), and then the Data1 (data byte). A read from the EEPROM would be a two-step process. The first step would be to do a ‘Write Byte’ with the EEPROM address in the Data0 register. The second step would be to do a ‘Receive Byte’ where the data is stored in the command register. Other differences from the SMBus specification: • Paragraph 5.5.5 – Read Byte/Word in figure 5-11: The PCA9558 follows this same command code with one exception, the PCA9558 requires 2 bytes of command before the repeated START. • Paragraph 5.5.6 – Process call in figure 5-15: The PCA9558 read operation is very similar to the SMBus process call. In the PCA9558 read operation you send a START condition – slave address with a write bit – 2 bytes of command code – repeated START – slave address with a read bit – then read data. PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 15 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 8. Application design-in information A central processor/controller typically located on the system main board can use the 400 kHz I2C-bus/SMBus to poll the PCA9558 devices located on the system cards for status or version control type of information. The PCA9558 may be programmed at manufacturing to store information regarding board build, firmware version, manufacturer identification, configuration option data, etc. Alternately, these devices can be used as convenient interface for board configuration, thereby utilizing the I2C-bus/SMBus as an intra-system communication bus. NXP 4-channel I2C-bus multiplexer ASIC I2C-bus configuration settings DIP switch or jumper replacement I2C-bus CPU OR μC I2C-bus PCA9558 BACKPLANE PCA9544A MUXED EEPROM I2C-bus I2C-bus CONTROL GPIO EEPROM monitoring and control INPUTS ALARM LEDs card ID, subroutines, configuration data, or revision history 002aad392 Fig 18. Typical application PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 16 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 9. Limiting values Table 9. Limiting values[1] In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VSS (0 V). Symbol Parameter Conditions VDD supply voltage VI input voltage [2] VO output voltage [2] Tstg storage temperature Min Max Unit 2.5 4.6 V −0.5 VDD + 0.5 V −0.5 VDD + 0.5 V −60 +150 °C [1] The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150 °C. [2] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 10. Recommended operating conditions Table 10. Operating conditions Symbol Parameter VDD supply voltage VIL LOW-level input voltage VIH HIGH-level input voltage VOL LOW-level output voltage Conditions Min 3 SCL, SDA; IOL = 3 mA −0.5 MUX_OUT_LOW, MUX_INx, MUX_SELECT −0.5 SCL, SDA; IOL = 3 mA 2.7 Typ Max Unit - 3.6 V - 0.9 V - 0.8 V - 4.0 V MUX_OUT_LOW, MUX_INx, MUX_SELECT 2.0 - 4.0 V SCL, SDA; IOL = 3 mA - - 0.4 V SCL, SDA; IOL = 6 mA - - 0.6 V IOL LOW-level output current MUX_OUTx, NON_MUXED_OUT; VOL = 0.4 V - - 4 mA IOH HIGH-level output current MUX_OUTx, NON_MUXED_OUT - - 100 μA Δt/ΔV input transition rise and fall rate 0 - 10 ns/V Tamb ambient temperature 0 - 70 °C PCA9558 Product data sheet operating All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 17 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 11. Static characteristics Table 11. Static characteristics Symbol Parameter Conditions Min Typ Max Unit 3.0 - 3.6 V Supply VDD supply voltage ICCL LOW-level supply current operating mode; all inputs = 0 V - - 10 mA ICCH HIGH-level supply current operating mode; all inputs = VDD - - 10 mA VPOR power-on reset voltage no load; VI = VDD or VSS - 2.3 2.6 V Input SCL; input/output SDA VIL LOW-level input voltage −0.5 - +0.8 V VIH HIGH-level input voltage 2 - VDD + 0.5 V IOL LOW-level output current VOL = 0.4 V 3 - - mA VOL = 0.6 V 6 - - mA ILH HIGH-level leakage current VI = VDD −1 - +1 μA ILL LOW-level leakage current VI = VSS −1 - +1 μA Ci input capacitance - - 10 pF MUX_OUT_LOW, WP, MUX_SELECT ILH HIGH-level leakage current VI = VDD - - 1 μA ILL LOW-level leakage current VI = VSS - - −100 μA Ci input capacitance - - 10 pF MUX_INx ILH HIGH-level leakage current VI = VDD - - 1 μA ILL LOW-level leakage current VI = VSS - - −100 μA Ci input capacitance - - 10 pF A0 input ILH HIGH-level leakage current VI = VDD - - 1 μA ILL LOW-level leakage current VI = VSS - - −100 μA Ci input capacitance - - 10 pF MUX_OUTx VOL IOH LOW-level output voltage HIGH-level output current IOL = 100 μA - - 0.4 V IOL = 4 mA - - 0.7 V VOH = VDD - - 100 μA NON_MUXED_OUT VOL IOH IOL = 100 μA - - 0.4 V IOL = 4 mA - - 0.7 V HIGH-level output current VOH = VDD - - 100 μA LOW-level output voltage IOL = 100 μA - - 0.4 V IOL = 4 mA - - 0.7 V VOH = VDD - - 100 μA LOW-level output voltage GPIO (IOx) VOL IOH HIGH-level output current PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 18 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 12. Dynamic characteristics Table 12. Symbol Dynamic characteristics Parameter Conditions Min Typ Max Unit MUX_INx to MUX_OUTx tPLH LOW to HIGH propagation delay - 21 28 ns tPHL HIGH to LOW propagation delay - 7 10 ns MUX_SELECT to MUX_OUTx tPLH LOW to HIGH propagation delay - 20 28 ns tPHL HIGH to LOW propagation delay - 8 12 ns MUX_OUT_LOW to NON_MUXED_OUT tPLH LOW to HIGH propagation delay - 20 26 ns tPHL HIGH to LOW propagation delay - 8 15 ns MUX_OUT_LOW to MUX_OUTx tPLH LOW to HIGH propagation delay - 20 28 ns tPHL HIGH to LOW propagation delay - 7.0 15 ns tr rise time output 1.0 - 10 ns/V tf fall time output 1.0 - 5 ns/V CL load capacitance test load on outputs - - 10 pF I2C-bus fSCL SCL clock frequency 10 - 400 kHz tBUF bus free time between a STOP and START condition 1.3 - - μs tHD;STA hold time (repeated) START condition 600 - - ns tLOW LOW period of the SCL clock 1.3 - - μs tHIGH HIGH period of the SCL clock 600 - −12 ns [1] tSU;STA set-up time for a repeated START condition 600 - −32 ns tHD;DAT data hold time 0 - 10 ns tSU;DAT data set-up time 100 - −100 ns tSP pulse width of spikes that must be suppressed by the input filter 0 - 50 ns tSU;STO set-up time for STOP condition 600 - 10 ns tr rise time of both SDA and SCL signals 10 pF to 400 pF bus 20 - 300 ns tf fall time of both SDA and SCL signals 10 pF to 400 pF bus 20 - 300 ns Cb capacitive load for each bus line - - 400 pF Tcy(W) write cycle time - 15 - ms [2] [1] After this period, the first clock pulse is generated. [2] Write cycle time can only be measured indirectly during the write cycle. During this time, the device will not acknowledge its I2C-bus address. PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 19 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 0.7 × VDD SDA 0.3 × VDD tr tBUF tf tHD;STA tSP tLOW 0.7 × VDD SCL 0.3 × VDD tHD;STA P tSU;STA tHD;DAT S tHIGH tSU;DAT tSU;STO Sr P 002aaa986 Fig 19. Definition of timing VI MUX input VM VM VSS tPZL tPLZ VDD MUX output VM VOL VOL + 0.3 V 002aad416 Fig 20. Open-drain output enable and disable times 13. Non-volatile storage specifications Table 13. PCA9558 Product data sheet Non-volatile storage specifications Parameter Specification memory cell data retention 10 years (minimum) number of memory cell write cycles 100,000 cycles (minimum) All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 20 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 14. Test information VDD VDD RL PULSE GENERATOR VI VO DUT CL RT 002aac532 RL = load resistor (1 kΩ) CL = load capacitance (includes jig and probe capacitance; 10 pF) RT = termination resistance; should be equal to Zo of pulse generators Fig 21. Test circuit for open-drain outputs PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 21 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 15. Package outline TSSOP28: plastic thin shrink small outline package; 28 leads; body width 4.4 mm D SOT361-1 E A X c HE y v M A Z 15 28 Q A2 (A 3) A1 pin 1 index A θ Lp 1 L 14 detail X w M bp e 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) θ mm 1.1 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 9.8 9.6 4.5 4.3 0.65 6.6 6.2 1 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.8 0.5 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT361-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 MO-153 Fig 22. Package outline SOT361-1 (TSSOP28) PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 22 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 16. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 16.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 16.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 16.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 23 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 16.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 23) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 14 and 15 Table 14. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 ≥ 350 < 2.5 235 220 ≥ 2.5 220 220 Table 15. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 23. PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 24 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 23. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 17. Abbreviations Table 16. PCA9558 Product data sheet Abbreviations Acronym Description ASIC Application Specific Integrated Circuit CDM Charged Device Model CPU Central Processing Unit DIP Dual In-line Package DUT Device Under Test EEPROM Electrically-Erasable Programmable Read-Only Memory ESD ElectroStatic Discharge GPIO General Purpose Input/Output HBM Human Body Model I/O Input/Output I2C-bus Inter-Integrated Circuit bus LED Light Emitting Diode LSB Least Significant Bit MSB Most Significant Bit POR Power-On Reset SMBus System Management Bus μC microcontroller All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 25 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 18. Revision history Table 17. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA9558 v.5 20120625 Product data sheet - PCA9558 v.4 Modifications: • • • Section 2 “Features and benefits”, 13th bullet: deleted “200 V MM per JESD22-A115” Table 8 “IOC - Input/Output Configuration register description”: default corrected from “1111 1111” to “0000 0000” (documentation correction only, there is no change in silicon) Table 16 “Abbreviations”: deleted row “MM, Machine Model” PCA9558 v.4 20090414 Product data sheet - PCA9558 v.3 PCA9558 v.3 (9397 750 11674) 20030627 Product data ECN 853-2235 29936 of 19 May 2003 PCA9558 v.2 PCA9558 v.2 (9397 750 09889) 20020524 Product data ECN 853-2235 28310 of 24 May 2002 PCA9558 v.1 PCA9558 v.1 20001204 Product specification - - PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 26 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 19. Legal information 19.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 19.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 19.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. PCA9558 Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 27 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 19.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP B.V. 20. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com PCA9558 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 25 June 2012 © NXP B.V. 2012. All rights reserved. 28 of 29 PCA9558 NXP Semiconductors 8-bit I2C-bus/SMBus I/O port 21. Contents 1 2 3 4 5 6 6.1 6.2 7 7.1 7.1.1 7.1.2 7.1.2.1 7.1.2.2 7.1.2.3 7.1.2.4 7.1.3 7.1.3.1 7.1.3.2 7.1.3.3 7.1.3.4 7.1.3.5 7.1.3.6 7.1.4 7.1.4.1 7.1.4.2 7.2 8 9 10 11 12 13 14 15 16 16.1 16.2 16.3 16.4 17 18 19 19.1 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 I2C-bus interface. . . . . . . . . . . . . . . . . . . . . . . . 5 Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 IP - Input Port register . . . . . . . . . . . . . . . . . . . 8 OP - Output Port register . . . . . . . . . . . . . . . . . 9 PI - Polarity Inversion register. . . . . . . . . . . . . . 9 IOC - Input/Output Configuration register . . . . . 9 EEPROM write operation . . . . . . . . . . . . . . . . 11 6-bit write operation . . . . . . . . . . . . . . . . . . . . 11 6-bit read operation . . . . . . . . . . . . . . . . . . . . 11 256-byte write operation (I2C-bus) . . . . . . . . . 12 256-byte read operation (I2C-bus) . . . . . . . . . 13 256-byte EEPROM write to GPIO. . . . . . . . . . 13 256-byte EEPROM write from GPIO . . . . . . . 14 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . 14 External reset . . . . . . . . . . . . . . . . . . . . . . . . . 14 Using the PCA9558 on the SMBus . . . . . . . . 15 Application design-in information . . . . . . . . . 16 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 17 Recommended operating conditions. . . . . . . 17 Static characteristics. . . . . . . . . . . . . . . . . . . . 18 Dynamic characteristics . . . . . . . . . . . . . . . . . 19 Non-volatile storage specifications . . . . . . . . 20 Test information . . . . . . . . . . . . . . . . . . . . . . . . 21 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 22 Soldering of SMD packages . . . . . . . . . . . . . . 23 Introduction to soldering . . . . . . . . . . . . . . . . . 23 Wave and reflow soldering . . . . . . . . . . . . . . . 23 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 23 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 24 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 26 Legal information. . . . . . . . . . . . . . . . . . . . . . . 27 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 27 19.2 19.3 19.4 20 21 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 27 28 28 29 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2012. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 25 June 2012 Document identifier: PCA9558