PCF2003DUS/DAAZ

PCF2003 32 kHz watch circuit with programmable adaptive motor pulse and pulse period Rev. 1.1 — 16 October 2019 Product data sheet 1. General description The PCF2003 is a CMOS integrated circuit for battery operated wrist watches with a 32 kHz quartz crystal as timing element and a bipolar 1 Hz stepping motor. The quartz crystal oscillator and the frequency divider are optimized for minimum power consumption. A timing accuracy of 1 ppm is achieved with a programmable, digital frequency adjustment. To obtain the minimum overall power consumption for the watch, an automatic motor pulse adaptation function is provided. The circuit supplies only the minimum drive current, which is necessary to ensure a correct motor step. Changing the drive current of the motor is achieved by chopping the motor pulse with a variable duty cycle. The pulse period and the range of the variable duty cycle can be programmed to suit different types of motors. The automatic pulse adaptation scheme is based on a safe dynamic detection of successful motor steps. A pad RESET is provided (used for stopping the motor) for accurate time setting and for accelerated testing of the watch. 2. Features and benefits  Amplitude-regulated 32 kHz quartz crystal oscillator, with excellent frequency stability and high immunity to leakage currents  Electrically programmable time calibration with 1 ppm resolution stored in One Time Programmable (OTP) memory  The quartz crystal is the only external component connected  Very low supply current, typical 90 nA  One second output pulses for bipolar stepping motor  Five different programmable output periods (1 s to 30 s)  Minimum power consumption for the entire watch, due to self adaptation of the motor drive according to the required torque  Reliable step detection circuit  Motor pulse width, pulse modulation, and pulse adaptation range programmable in a wide range, stored in OTP memory  Stop function for accurate time setting and power saving during shelf life  Test mode for accelerated testing of the mechanical parts of the watch and the IC  Test bits for type recognition PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 3. Applications  Driver circuits for bipolar stepping motors  High immunity motor drive circuits 4. Ordering information Table 1. Ordering information Type number Topside marking Package Name Description Version PCF2003DUS/DA P3 WLCSP8 wafer level chip-size package; 8 bumps; 1.16 mm x 0.86 mm PCF2003DUS 4.1 Ordering options Table 2. Ordering options Type number Orderable part number PCF2003DUS/DA PCF2003DUS/DAAZ Package Packing method Minimum Temperature order quantity WLCSP8 chips with solder bumps 4000 in tape and reel, 7 inch, dry pack Tamb = 10 C to +60 C 5. Block diagram 32 Hz 8 kHz OSCIN OSCOUT 3 4 OSCILLATOR DIVIDER ÷4 RESET VSS RESET reset TIMING ADJUSTMENT, INHIBITION VDD 8 5 1 VOLTAGE DETECTOR, OTP-CONTROLLER OTP-MEMORY 1 Hz MOTOR CONTROL WITH ADAPTIVE PULSE MODULATION i.c. 2 STEP DETECTION PCF2003 6 MOT1 Fig 1. PCF2003 Product data sheet 7 MOT2 aaa-016619 Block diagram of PCF2003 All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 2 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 6. Pinning information 6.1 Pinning PCF2003DUS/DA VSS i.c. RESET 1 2 8 OSCIN 7 3 MOT2 4 6 5 OSCOUT MOT1 VDD aaa-016630 Viewed from active side. For mechanical details, see Figure 13. Fig 2. Pin configuration of PCF2003DUS/DA 6.2 Pin description Table 3. Pin description Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Pin Description VSS[1] 1 ground i.c.[2] 2 internally connected OSCIN 3 oscillator input OSCOUT 4 oscillator output VDD 5 supply voltage MOT1 6 motor 1 output MOT2 7 motor 2 output RESET 8 reset input [1] The substrate (rear side of the chip) is connected to VSS. Therefore the die pad must be either floating or connected to VSS. [2] Pad i.c. is used for factory tests; in normal operation it should be left open-circuit, and it has an internal pull-down resistance to VSS. 7. Functional description 7.1 Motor pulse The motor output supplies pulses of different driving stages, depending on the torque required to turn on the motor. The number of different stages can be selected between three and six. With the exception of the highest driving stage, each motor pulse (tp in Figure 3 and Figure 6) is followed by a detection phase during which the motor movement is monitored, in order to check whether the motor has turned correctly or not. PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 3 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 1.96 ms tp tp detection phase 2t p mgw350 0.98 ms 31.25 ms Fig 3. 31.25 ms Correction sequence after failed motor step If a missing step is detected, a correction sequence is generated (see Figure 3) and the driving stage is switched to the next level. The correction sequence consists of two pulses: first a short pulse in the opposite direction (0.98 ms, modulated with the maximum duty cycle) to give the motor a defined position, followed by a motor pulse of the strongest driving level. Every 4 minutes, the driving level is lowered again by one stage. The motor pulse has a constant pulse width. The driving level is regulated by chopping the driving pulse with a variable duty cycle. The driving level starts from the programmed minimum value and increases by 6.25 % after each failed motor step. The strongest driving stage, which is not followed by a detection phase, is programmed separately. Therefore, it is possible to program a larger energy gap between the pulses with step detection and the strongest, not monitored, pulse. This might be necessary to ensure a reliable and stable operation under adverse conditions (magnetic fields and vibrations). If the watch works in the highest driving stage, the driving level jumps after the 4-minute period directly to the lowest stage, and not just one stage lower. To optimize the performance for different motors, the following parameters can be programmed: • • • • • Pulse width: 0.98 ms to 7.8 ms in steps of 0.98 ms Duty cycle of lowest driving level: 37.5 % to 56.25 % in steps of 6.25 % Number of driving levels (including the highest driving level): 3 to 6 Duty cycle of the highest driving level: 75 % or 100 % Enlargement pulse for the highest driving level: on or off The enlargement pulse has a duty cycle of 25 % and a pulse width which is twice the programmed motor pulse width. The repetition period for the chopping pattern is 0.98 ms. Figure 4 shows an example of a 3.9 ms pulse. PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 4 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse DUTY CYCLE 0.244 ms 0.122 ms 37.5 % 43.75 % 50 % 56.25 % 62.5 % 68.75 % 75 % 81.25 % 100 % 0.98 ms Fig 4. PCF2003 Product data sheet 0.98 ms 0.98 ms 0.98 ms mgw351 Possible modulations for a 3.9 ms motor pulse All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 5 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 7.2 Step detection Figure 5 shows a simplified diagram of the motor driving and step detection circuit, and Figure 6 shows the step detection sequence and corresponding sampling current. Between the motor driving pulses, the switches P1 and P2 are closed, which means the motor is short-circuited. For a pulse in one direction, P1 and N2 are open, and P2 and N1 are closed with the appropriate duty cycle; for a pulse in the opposite direction, P2 and N1 are open, and P1 and N2 closed. VDD RD D1 P1 P3 P2 P4 MOTOR MOT1 N1 MOT2 N2 VSS Fig 5. mgw352 Simplified diagram of motor driving and step detection circuit The step detection phase is initiated after the motor driving pulse. In phase 1 P1 and P2 are first closed for 0.98 ms and then in phase 2 all four drive switches (P1, N1, P2 and N2) are opened for 0.98 ms. As a result, the energy stored in the motor inductance is reduced as fast as possible. The induced current caused by the residual motor movement is then sampled in phase 3 (closing P3 and P2) and in phase 4 (closing P1 and P4). For step detection in the opposite direction P1 and P4 are closed during phase 3 and P2 and P3 during phase 4 (see Figure 6). PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 6 of 28 PCF2003 NXP Semiconductors phase 2 phase 4 I motor phase 3 phase 1 32 kHz watch circuit with programmable adaptive motor pulse positive detection level t negative detection level tp 0.98 ms (motor shorted) t d = 0.98 ms sampling voltage programmable time limit OTP C4 to C6 sampling t sampling voltage positive detection negative detection sampling results t motor shorted sampling 61 μs Fig 6. 0.49 ms mgw569 Step detection sequence and corresponding sampling voltage The condition for a successful motor step is a positive step detection pulse (current in the same direction as in the driving phase) followed by a negative detection pulse within a given time limit. This time limit can be programmed between 3.9 ms and 10.7 ms (in steps of 0.98 ms) in order to ensure a safe and correct step detection under all conditions (for instance magnetic fields). The step detection phase stops after the last 31.25 ms, after the start of the motor driving pulse. 7.3 Time calibration The quartz crystal oscillator has an integrated capacitance of 5.2 pF, which is lower than the specified capacitance (CL) of 8.2 pF for the quartz crystal (see Table 11). Therefore, the oscillator frequency is typically 60 ppm higher than 32.768 kHz. This positive frequency offset is compensated by removing the appropriate number of 8192 Hz pulses in the divider chain (maximum 127 pulses), every 1 or 2 minutes. The time correction is given in Table 4. Table 4. Time calibration Calibration period Correction per step (n = 1) 1 minute 2.03 0.176 258 22.3 2 minutes 1.017 0.088 129 11.15 ppm Correction per step (n = 127) Seconds per day ppm Seconds per day After measuring the effective oscillator frequency, the number of correction pulses must be calculated and stored together with the calibration period in the OTP memory (see Section 7.7). PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 7 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse The oscillator frequency can be measured at pad RESET, where a square wave signal 1 with the frequency of ------------  f osc is provided. This frequency shows a jitter every minute or 1024 every two minutes, which originates from the time calibration, depending on the programmed calibration period. Details on how to measure the oscillator frequency and the programmed inhibition time are given in Section 7.10. 7.4 Reset 1 At pad RESET an output signal with a frequency of ------------  f osc = 32 Hz is provided. 1024 Connecting pad RESET to VDD stops the motor drive and opens all four (P1, N1, P2 and N2) driver switches (see Figure 5). Connecting pad RESET to VSS activates the test mode. In this mode the motor output frequency is 32 Hz, which can be used to test the mechanical function of the watch. After releasing the pad RESET, the motor starts exactly one second later with the smallest duty cycle and with the opposite polarity to the last pulse before stopping. The debounce time for the RESET function is between 31 ms and 62 ms. 7.5 Programming possibilities The programming data is stored in OTP cells (EPROM cells). At delivery, all memory cells are in state 0. The cells can be programmed to the state 1, but then there is no more set back to state 0. The programming data is organized in an array of four 8-bit words (see Table 5): word A contains the time calibration, words B and C contain the setting for the motor pulses and word D contains the type recognition. Table 5. Word Words and bits Bit 1 2 3 4 A number of 8192 Hz pulses to be removed B lowest stage: duty cycle C pulse width D type 5 6 7 8 calibration period number of driving stages highest stage: duty cycle pulse stretching maximum time delay between positive and negative detection pulses output period output period factory test bit factory test bits Table 6. Description of word A bits Bit Value Description - adjust the number of the 8192 Hz pulses to be removed; bit 1 is the MSB and bit 7 is the LSB 0 1 minute 1 2 minutes Inhibition time 1 to 7 Calibration period 8 PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 8 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse Table 7. Description of word B bits Bit Value Description Duty cycle lowest driving stage 1 to 2 00 37.5 % 01 43.75 % 10 50 % 11 56.25 % Number of driving stages 3 to 4 00 3 01 4 10 5 11 6[1] Duty cycle highest driving stage 5 0 75 %[2] 1 100 % 0 no pulse stretching 1 pulse of 2  tp and duty cycle of 25 % are added 00 1s 01 5s 10 10 s 11 20 s Pulse stretching 6 Output period 7 to 8 PCF2003 Product data sheet [1] Including the highest driving stage, which one has no motor step detection. [2] If the maximum duty cycle of 75 % is selected, not all programming combinations are possible since the second highest level must be smaller than the highest driving level. All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 9 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse Table 8. Description of word C bits Bit Value Description 000 0.98 ms 001 1.95 ms 010 2.90 ms 011 3.90 ms 100 4.90 ms 101 5.90 ms 110 6.80 ms 111 7.80 ms Pulse width tp 1 to 3 Time delay td(max) [1] 4 to 6 000 3.91 ms 001 4.88 ms 010 5.86 ms 011 6.84 ms 100 7.81 ms 101 8.79 ms 110 9.77 ms 111 10.74 ms 0 bit 7 and 8 of word B active 1 30 s, bit 7 and 8 of word B inactive - - Output period 7 Factory test bit 8 [1] Between positive and negative detection pulses. Byte D is read to determine which type of the PCA200x family is used in a particular application. Table 9. Description of word D bits Bit Value Description 0000 PCA2002 1000 PCA2000 0100 PCA2001 1100 PCA2003 - - Type recognition 1 to 4 Factory test bits 5 to 8 PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 10 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 7.6 Programming procedure For a watch it is essential that the timing calibration can be made after the watch is fully assembled. In this situation, the supply pads are often the only terminals which are still accessible. Writing to the OTP cells and performing the related functional checks is achieved in the PCF2003 by modulating the supply voltage. The necessary control circuit consists basically of a voltage level detector, an instruction counter which determines the function to be performed, and an 8-bit shift register which allows writing to the OTP cells of an 8-bit word in one step and acts as a data pointer for checking the OTP content. There are six different instruction states (state 3 and state 5 are handled as state 4): • • • • • • State 1: measurement of the quartz crystal oscillator frequency (divided by 1024) State 2: measurement of the inhibition time State 3: write/check word A State 4: write/check word B State 5: write/check word C State 6: check word D (type recognition) Each instruction state is switched on with a pulse to VP(prog)(start). After this large pulse, an initial waiting time of t0 is required. The programming instructions are then entered by modulating the supply voltage with small pulses (amplitude VP(mod) and pulse width tmod). The first small pulse defines the start time, the following pulses perform three different functions, depending on the time delay (td) from the preceding pulse (see Figure 7, Figure 8, Figure 11 and Figure 12): • td = t1 (0.7 ms); increments the instruction counter • td = t2 (1.7 ms); clocks the shift register with data = logic 0 • td = t3 (2.7 ms); clocks the shift register with data = logic 1 The programming procedure requires a stable oscillator. This means that a waiting time, determined by the start-up time of the oscillator is necessary after power-on of the circuit. After the VP(prog)(start) pulse, the instruction counter is in state 1 and the data shift register is cleared. The instruction state ends with a second pulse to VP(prog)(stop) or with a pulse to Vstore. In any case, the instruction states are terminated automatically 2 seconds after the last supply modulation pulse. 7.7 Programming the memory cells Applying the two-stage programming pulse (see Figure 7) transfers the stored data in the shift register to the OTP cells. Perform the following to program a memory word: 1. Starting with a VP(prog)(start) pulse wait for the time period t0 then set the instruction counter to the word to be written (td = t1). PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 11 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 2. Enter the data to be stored in the shift register (td = t2 or t3). LSB first (bit 8) and the MSB last (bit 1). 3. Applying the two-stage programming pulse Vprestore followed by Vstore stores the word. The delay between the last data bit and the prestore pulse Vprestore is td = t4. Store the word by raising the supply voltage to Vstore; the delay between the last data bit and the store pulse is td. The example shown in Figure 7 performs the following functions: • • • • Start Setting instruction counter to state 4 (word B) Entering data word 110101 into the shift register (sequence: LSB first and MSB last) Writing to the OTP cells for word B tw(prestore) VDD Vstore tp(start) VP(prog)(start) Vprestore t0 t1 t1 t1 t3 t2 t3 t2 t3 t3 t4 tw(store) VP(mod) VDD(nom) VSS mgw356 VDD(nom): nominal supply voltage. The example shows the programming of B = 110101 (the sequence is MSB first and LSB last). Fig 7. Supply voltage modulation for programming 7.8 Checking memory content The stored data of the OTP array can be checked bit wise by measuring the supply current. The array word is selected by the instruction state and the bit is addressed by the shift register. To read a word, the word is first selected (td = t1), and a logic 1 is written into the first cell of the shift register (td = t3). This logic 1 is then shifted through the entire shift register (td = t2), so that it points with each clock pulse to the next bit. If the addressed OTP cell contains a logic 1, a 30 k resistor is connected between VDD and VSS, which increases the supply current accordingly. Figure 8 shows the supply voltage modulation for reading word B, with the corresponding supply current variation for word B = 110101 (sequence: first MSB and last LSB). PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 12 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse VDD tp(start) tp(stop) VP(prog)(start) VP(prog)(stop) t0 t1 t1 t1 t3 t2 t2 t2 t2 t2 VP(mod) VDD(nom) VSS IDD (1) mgw357 VDD(nom): nominal supply voltage. V DD (1) I DD = --------------30 k Fig 8. PCF2003 Product data sheet Supply voltage modulation and corresponding supply current variation for reading word B All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 13 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 7.9 Frequency tuning of assembled watch Figure 9 shows the test set-up for frequency tuning the assembled watch. 32 kHz M PCF200x FREQUENCY COUNTER motor PROGRAMMABLE DC POWER SUPPLY battery PC INTERFACE PC aaa-016631 Fig 9. Frequency tuning the assembled watch 7.10 Measurement of oscillator frequency and inhibition time The output of the two measuring states can either be monitored directly at pad RESET or as a modulation of the supply voltage (a modulating resistor of 30 k is connected between VDD and VSS when the signal at pad RESET is at HIGH-level). The supply voltage modulation must be followed as shown in Figure 10 in order to guarantee the correct start-up of the circuit during production and testing. VDD tp(stop) VP(prog)(stop) td(start) > 500 ms VDD(nom) VSS 001aac503 VDD(nom): nominal supply voltage. Fig 10. Supply voltage at start-up during production and testing Measuring states: PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 14 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse • State 1: quartz crystal oscillator frequency divided by 1024; state 1 starts with a pulse to VP and ends with a second pulse to VP • State 2: inhibition time has a value of n  0.122 ms. A signal with periodicity of 31.25 ms + n  0.122 ms appears at pad RESET and as current modulation at pad VDD (see Figure 11 and Figure 12) 31.25 ms + inhibition time VDD VO(dif) VSS mgw355 Fig 11. Output waveform at pad RESET for instruction state 2 VDD t p(stop) t p(start) VP(prog)(stop) VP(prog)(start) t0 t1 VP(mod) VDD(nom) VSS mgu719 VDD(nom): nominal supply voltage. Fig 12. Supply voltage modulation for starting and stopping of instruction state 2 7.11 Customer testing Connecting pad RESET to VSS activates the test mode. In this test mode, the motor output frequency is 8 Hz; the duty cycle reduction and battery check occurs every second, instead of every 4 minutes. 8. Safety notes CAUTION This device is sensitive to ElectroStatic Discharge (ESD). Observe precautions for handling electrostatic sensitive devices. Such precautions are described in the ANSI/ESD S20.20, IEC/ST 61340-5, JESD625-A or equivalent standards. CAUTION Semiconductors are light sensitive. Exposure to light sources can cause the IC to malfunction. The IC must be protected against light. The protection must be applied to all sides of the IC. PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 15 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 9. Limiting values Table 10. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VDD supply voltage VSS = 0 V 1.8 +7.0 V VI input voltage on all supply pins 0.5 +7.5 V tsc short circuit duration time output - indefinite s Tamb ambient temperature VESD Ilu Tstg [1][2] 10 +60 C HBM [3] - 2000 V MM [4] - 200 V latch-up current [5] - 100 mA storage temperature [6] 30 +100 C electrostatic discharge voltage [1] When writing to the OTP cells, the supply voltage (VDD) can be raised to a maximum of 12 V for a time period of 1 s. [2] Connecting the battery with reversed polarity does not destroy the circuit, but in this condition a large current flows, which rapidly discharges the battery. [3] Pass level; Human Body Model (HBM), according to Ref. 6 “JESD22-A114”. [4] Pass level; Machine Model (MM), according to Ref. 7 “JESD22-A115”. [5] Pass level; latch-up testing according to Ref. 8 “JESD78” at maximum ambient temperature (Tamb(max)). [6] According to the store and transport requirements (see Ref. 10 “UM10569”) the devices have to be stored at a temperature of +8 C to +45 C and a humidity of 25 % to 75 %. PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 16 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 10. Characteristics Table 11. Characteristics VDD = 1.55 V; VSS = 0 V; fosc = 32.768 kHz; Tamb = 25 C; quartz crystal: RS = 40 k, C1 = 2 fF to 3 fF, CL = 8.2 pF; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit VDD supply voltage normal operating mode; Tamb = 10 C to +60 C 1.1 1.55 3.60 V VDD supply voltage variation V/t = 1 V/s - - 0.25 V IDD supply current between motor pulses - 90 120 nA between motor pulses at VDD = 3.5 V - 120 180 nA Tamb = 10 C to +60 C - - 200 nA stop mode; pad RESET connected to VDD - 100 135 nA - 150 200 mV - 200 300  1.1 - - V 5 10 - S - 0.3 0.9 s - 0.05 0.20 ppm 4.3 5.2 6.3 pF 20 - - M Supply Motor output Vsat saturation voltage Rmotor = 2 k; Tamb = 10 C to +60 C Zo(sc) output impedance (short circuit) between motor pulses; Imotor < 1 mA [1] Oscillator Vstart start voltage gm transconductance tstartup start-up time f/f frequency stability CL(itg) integrated load capacitance Rpar parasitic resistance Vi(osc)  50 mV (p-p) VDD = 100 mV allowed resistance between adjacent pads Pad RESET fo output frequency - 32 - Hz 1.4 - - V VO(dif) differential output voltage RL = 1 M; CL = 10 pF [2] tr rise time RL = 1 M; CL = 10 pF [2] - 1 - s [2] - 1 - s - 10 20 nA tf fall time RL = 1 M; CL = 10 pF Ii(AV) average input current pad RESET connected to VDD or VSS [1] P1 + ... + P4 + N1 + N2 (see Section 7.2). [2] RL and CL are a load resistor and load capacitor, externally connected to pad RESET. PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 17 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 11. OTP programming characteristics Table 12. Specifications for OTP programming See Figure 7, Figure 8 and Figure 12. Symbol Parameter[1] Conditions Min Typ Max Unit VDD supply voltage during programming procedure 1.5 - 3.0 V VP(prog)(start) programming supply voltage (start) 6.6 - 6.8 V VP(prog)(stop) programming supply voltage (stop) 6.2 - 6.4 V VP(mod) supply voltage modulation for entering instructions, referred to VDD 320 350 380 mV Vprestore prestore voltage for prestore pulse 6.2 - 6.4 V Vstore store voltage for writing to the OTP cells 9.9 10.0 10.1 V Istore store current for writing to the OTP cells - - 10 mA tp(start) start pulse width 8 10 12 ms tp(stop) pulse width of stop pulse 0.05 - 0.5 ms tmod modulation pulse width 25 30 40 s tw(prestore) prestore pulse width 0.05 - 0.5 ms tw(store) store pulse width for writing to the OTP cells 95 100 110 ms t0 time 0 waiting time after start pulse 20 - 30 ms t1 time 1 pulse distance for incrementing the state counter 0.6 0.7 0.8 ms t2 time 2 pulse distance for clocking the data register with data = logic 0 1.6 1.7 1.8 ms t3 time 3 pulse distance for clocking the data register with data = logic 1 2.6 2.7 2.8 ms t4 time 4 waiting time for writing to OTP cells 0.1 0.2 0.3 ms SR slew rate for modulation of the supply voltage 0.5 - 5.0 V/s Rmod modulation resistance supply current modulation read-out resistor 18 30 45 k [1] Program each word once only. PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 18 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 12. Bare die outline WLCSP8: wafer level chip-size package; 8 bumps PCF2003DUS D b 1 2 8 (1) y 3 x 0 E 0 4 7 6 5 A1 A2 A Note 1. Marking code Outline version Figure not drawn to scale wlcsp8_pcf2003dus_do References IEC JEDEC European projection JEITA Issue date 15-01-29 15-10-15 PCF2003DUS (1) Marking code PC2003-1 Fig 13. Bare die outline of PCF2003DUS (for dimensions see Table 13, for pin location see Table 14) Table 13. Dimension of PCF2003US Original dimensions are in mm. Unit (mm) PCF2003 Product data sheet A A1 A2 b D E max - - - - 1.19 0.89 nom 0.53 0.15 0.38 0.20 1.16 0.86 min - - - - 1.13 0.83 All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 19 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse Table 14. Symbol Bonding pad description Pin X[1] Y[1] Type Description 1 430 280 supply ground i.c.[3] 2 0 280 - internally connected OSCIN 3 225 0 input oscillator input OSCOUT 4 430 280 output oscillator output VSS [2] VDD 5 430 280 supply supply voltage MOT1 6 0 280 output motor 1 output MOT2 7 225 0 output motor 2 output RESET 8 430 280 input reset input [1] All coordinates are referenced, in m, to the center of the die (see Figure 13). [2] The substrate (rear side of the chip) is connected to VSS. Therefore the die pad must be either floating or connected to VSS. [3] Pad i.c. is used for factory tests; in normal operation it should be left open-circuit, and it has an internal pull-down resistance to VSS. 13. Handling information All input and output pins are protected against ElectroStatic Discharge (ESD) under normal handling. When handling Metal-Oxide Semiconductor (MOS) devices ensure that all normal precautions are taken as described in JESD625-A, IEC 61340-5 or equivalent standards. PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 20 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 14. Packing information 14.1 Tape and reel information TOP VIEW Ø D0 P0 W T B0 P1 A0 X K0 direction of feed pin 1 L The die has active side facing down, pin 1 towards the sprocket holes with “L” mark on topside. detail X Original dimensions are in mm. Figure not drawn to scale. aaa-019803 Fig 14. Tape and reel details for PCF2003DUS Table 15. Carrier tape dimensions of PCF2003DUS Nominal values with production tolerances. Symbol Description Value Unit A0 pocket width in x direction 1.00  0.05 mm B0 pocket width in y direction 1.30  0.05 mm K0 pocket depth 0.62  0.05 mm Compartments Overall dimensions PCF2003 Product data sheet W tape width 8 mm T tape thickness 0.2  0.02 mm D0 sprocket hole diameter 1.5 mm P0 sprocket hole pitch 4  0.1 mm P1 pocket pitch 4  0.1 mm All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 21 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 15. Soldering of WLCSP packages 15.1 Introduction to soldering WLCSP packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering WLCSP (Wafer Level Chip-Size Packages) can be found in application note AN10439 “Wafer Level Chip Scale Package” and in application note AN10365 “Surface mount reflow soldering description”. Wave soldering is not suitable for this package. All NXP WLCSP packages are lead-free. 15.2 Board mounting Board mounting of a WLCSP requires several steps: 1. Solder paste printing on the PCB 2. Component placement with a pick and place machine 3. The reflow soldering itself 15.3 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 15) than a SnPb process, thus reducing the process window • Solder paste printing issues, such as smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature), and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic) while being low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 16. Table 16. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 15. PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 22 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 15. Temperature profiles for large and small components For further information on temperature profiles, refer to application note AN10365 “Surface mount reflow soldering description”. 15.3.1 Stand off The stand off between the substrate and the chip is determined by: • The amount of printed solder on the substrate • The size of the solder land on the substrate • The bump height on the chip The higher the stand off, the better the stresses are released due to TEC (Thermal Expansion Coefficient) differences between substrate and chip. 15.3.2 Quality of solder joint A flip-chip joint is considered to be a good joint when the entire solder land has been wetted by the solder from the bump. The surface of the joint should be smooth and the shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps after reflow can occur during the reflow process in bumps with high ratio of bump diameter to bump height, i.e. low bumps with large diameter. No failures have been found to be related to these voids. Solder joint inspection after reflow can be done with X-ray to monitor defects such as bridging, open circuits and voids. 15.3.3 Rework In general, rework is not recommended. By rework we mean the process of removing the chip from the substrate and replacing it with a new chip. If a chip is removed from the substrate, most solder balls of the chip will be damaged. In that case it is recommended not to re-use the chip again. PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 23 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse Device removal can be done when the substrate is heated until it is certain that all solder joints are molten. The chip can then be carefully removed from the substrate without damaging the tracks and solder lands on the substrate. Removing the device must be done using plastic tweezers, because metal tweezers can damage the silicon. The surface of the substrate should be carefully cleaned and all solder and flux residues and/or underfill removed. When a new chip is placed on the substrate, use the flux process instead of solder on the solder lands. Apply flux on the bumps at the chip side as well as on the solder pads on the substrate. Place and align the new chip while viewing with a microscope. To reflow the solder, use the solder profile shown in application note AN10365 “Surface mount reflow soldering description”. 15.3.4 Cleaning Cleaning can be done after reflow soldering. 16. Abbreviations Table 17. Abbreviations Acronym Description CMOS Complementary Metal Oxide Semiconductor HBM Human Body Model LSB Least Significant Bit MM Machine Model MSB Most Significant Bit OTP One Time Programmable 17. References [1] AN10365 — Surface mount reflow soldering description [2] AN10439 — Wafer Level Chip Size Package [3] AN10706 — Handling bare die [4] IEC 60134 — Rating systems for electronic tubes and valves and analogous semiconductor devices [5] IEC 61340-5 — Protection of electronic devices from electrostatic phenomena [6] JESD22-A114 — Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM) [7] JESD22-A115 — Electrostatic Discharge (ESD) Sensitivity Testing Machine Model (MM) [8] JESD78 — IC Latch-Up Test [9] JESD625-A — Requirements for Handling Electrostatic-Discharge-Sensitive (ESDS) Devices [10] UM10569 — Store and transport requirements PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 24 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 18. Revision history Table 18. Revision history Document ID Release date Data sheet status Change notice Supersedes PCF2003 v.1.1 20191016 Product data sheet 201910008I PCF2003 v.1 Modifications: PCF2003 v.1 PCF2003 Product data sheet • Topside marking changed from blank to “P3” for new manufacturing flow 20151020 Product data sheet - All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 - © NXP Semiconductors N.V. 2019. All rights reserved. 25 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 19. Legal information 19.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 19.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 19.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. PCF2003 Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 26 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Bare die — All die are tested on compliance with their related technical specifications as stated in this data sheet up to the point of wafer sawing and are handled in accordance with the NXP Semiconductors storage and transportation conditions. If there are data sheet limits not guaranteed, these will be separately indicated in the data sheet. There are no post-packing tests performed on individual die or wafers. NXP Semiconductors has no control of third party procedures in the sawing, handling, packing or assembly of the die. Accordingly, NXP Semiconductors assumes no liability for device functionality or performance of the die or systems after third party sawing, handling, packing or assembly of the die. It is the responsibility of the customer to test and qualify their application in which the die is used. All die sales are conditioned upon and subject to the customer entering into a written die sale agreement with NXP Semiconductors through its legal department. 19.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 20. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com PCF2003 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 16 October 2019 © NXP Semiconductors N.V. 2019. All rights reserved. 27 of 28 PCF2003 NXP Semiconductors 32 kHz watch circuit with programmable adaptive motor pulse 21. Contents 1 2 3 4 4.1 5 6 6.1 6.2 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Motor pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Step detection. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Time calibration . . . . . . . . . . . . . . . . . . . . . . . . 7 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Programming possibilities. . . . . . . . . . . . . . . . . 8 Programming procedure . . . . . . . . . . . . . . . . . 11 Programming the memory cells . . . . . . . . . . . 11 Checking memory content . . . . . . . . . . . . . . . 12 Frequency tuning of assembled watch . . . . . . 14 Measurement of oscillator frequency and inhibition time . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.11 Customer testing . . . . . . . . . . . . . . . . . . . . . . 15 8 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 9 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 16 10 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 17 11 OTP programming characteristics . . . . . . . . . 18 12 Bare die outline . . . . . . . . . . . . . . . . . . . . . . . . 19 13 Handling information. . . . . . . . . . . . . . . . . . . . 20 14 Packing information . . . . . . . . . . . . . . . . . . . . 21 14.1 Tape and reel information . . . . . . . . . . . . . . . . 21 15 Soldering of WLCSP packages. . . . . . . . . . . . 22 15.1 Introduction to soldering WLCSP packages . . 22 15.2 Board mounting . . . . . . . . . . . . . . . . . . . . . . . 22 15.3 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 22 15.3.1 Stand off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 15.3.2 Quality of solder joint . . . . . . . . . . . . . . . . . . . 23 15.3.3 Rework . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 15.3.4 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 16 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 24 17 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 25 19 Legal information. . . . . . . . . . . . . . . . . . . . . . . 26 19.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 26 19.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 19.3 19.4 20 21 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 27 27 28 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP Semiconductors N.V. 2019. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 16 October 2019 Document identifier: PCF2003