SSL8516T
Greenchip PFC and flyback controller
Rev. 1 — 5 May 2014
Product data sheet
1. General description
The GreenChip is the latest generation of green Switched Mode Power Supply (SMPS)
controller ICs. The SSL8516T combines a controller for Power Factor Correction (PFC)
and a flyback controller. Its high level of integration enables cost-effective LED lighting
application power supply design using a very low number of external components.
The PFC operates in Quasi-Resonant (QR) or Discontinuous Conduction Mode (DCM),
with valley switching.
The specially built-in green functions provide high efficiency at all power levels. At high
power levels, the flyback operates in QR mode or DCM with valley detection. At medium
power levels, the flyback controller switches to Frequency Reduction (FR) mode and limits
the peak current to an adjustable minimum value. It ensures high efficiency while
minimizing the audible noise from the transformer. In low-power mode, the PFC switches
off to maintain high efficiency. Valley switching is used in all operating modes.
The SSL8516T is a Multi-Chip Module (MCM), containing two chips. The proprietary
high-voltage BCD800 process makes direct start-up possible from the rectified universal
mains voltage in an effective and green way. The second low voltage Silicon-On-Insulator
(SOI) is used for accurate, high-speed protection functions and control.
The SSL8516T enables easy design of highly efficient and reliable LED lighting
application power supplies between 25 W and 300 W.
LED drivers in particular benefit from the high level of integration. The IC meets the
lighting class C requirements on mains current harmonics as specified by IEC 61000-3-2
over a wide input voltage range and a wide output power range.
Remark: All values in this document are typical values unless otherwise stated.
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
2. Features and benefits
2.1 Distinctive features
Integrated PFC and flyback controller
Universal mains supply operation between 90 V (AC) to 305 V (AC)
Fixed boost PFC with accurate maximum output voltage (NXP Semiconductors
patented)
High level of integration, results in cost-effective designs with very low external
component counts
Adjustable PFC switch off delay
External PFC switch on and switch off override
Accurate PFC switch on and switch off control (NXP Semiconductors patent pending)
2.2 Green features
On-chip start-up current source
Power-down functionality for very low standby power
2.3 PFC green features
Valley/Zero-Voltage Switching (ZVS) for minimum switching losses
(NXP Semiconductors patented)
Frequency limitation reduces switching losses
PFC switched off when a low-load is detected at the flyback output
2.4 Flyback green features
Valley switching for minimum switching losses (NXP Semiconductors patented)
Frequency reduction with adjustable minimum peak current at low-power operation
maintains high-efficiency at low output power levels
2.5 Protection features
Safe restart mode for system fault conditions
Continuous mode protection using demagnetization detection for both converters
(NXP Semiconductors patented)
UnderVoltage Protection (UVP) (foldback during overload)
Accurate OverVoltage Protection (OVP) for both converters (adjustable for flyback
converter)
Mains voltage independent OverPower Protection (OPP)
Open control loop protection for both converters. The open-loop protection on the
flyback converter is safe restart
OverTemperature Protection (OTP)
Low and adjustable OverCurrent Protection (OCP) trip level for both converters
General-purpose input for latched protection, for use with system OverTemperature
Protection (OTP)
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
2 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
3. Applications
This IC can be used in all lighting applications requiring efficient and cost-effective
AC-DC offline switch mode power solutions from 25 W to 300 W.
4. Ordering information
Table 1.
Ordering information
Type number
Package
SSL8516T
Name
Description
Version
SO16
plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1
5. Block diagram
3)&'5,9(5
)%'5,9(5
9
9HQ 3)& )%&75/
3)&GULYHU
IO\EDFNGULYHU
3)&JDWH
GULYHU
SRZHU
GRZQ
ORZ9LQ
9,16(16(
$
ORZSRZHU
3)& VZRQ
3)& VZRII
&21752/
GULYHU
/$7&+
H[WHUQDO
SURWHFWLRQ
IO\EDFNJDWH
P9
SURWHFWLRQ
ODWFK
UHVHW
3)&&203
5
3)&
0$;,080
SURWHFWLRQ SURWHFWLRQ
5
4
4
6
HQDEOH3)&
6
9
IUHTXHQF\
UHGXFWLRQ
HQDEOHIO\EDFN
9
$
FODPS
9
9
ORZ
9 LQ
926(16(
9
9
3)&
26&,//$725
WRQ IE PD[
)/ VOVP(VOSENSE)), the PFC controller
stops switching until the VVOSENSE < VOVP(VOSENSE). If a mains UVP is detected,
VVINSENSE < Vstop(VINSENSE), the PFC controller stops switching until
VVINSENSE > Vstart(VINSENSE) again. OVP and UVP of the PFC circuit do not disable flyback
controller switching.
When the VCC pin voltage drops under the UVLO level, both controllers stop switching and
enter safe restart mode. In the safe restart mode, the VCC pin capacitor is recharged using
Ich(low) from the HV pin.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
6 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
,+9
9VWDUWXS
9WK 89/2
9WULS
9&&
9VWDUW 9,16(16(
9,16(16(
9HQ 3)&&203
3)&&203
9HQ /$ 7&+
/$7&+
3527(&7,21
VRIWVWDUW
3)&6(16(
3)&'5,9(5
VRIWVWDUW
)%6(16(
)%'5,9(5
9WR )%&75/
)%&75/
9WK VWDUW 926(16(
926(16(
92
FKDUJLQJ9&&
FDSDFLWRU
VWDUWLQJ
FRQYHUWHUV
QRUPDO
RSHUDWLRQ
SURWHFWLRQ
UHVWDUW
DDD
The protection signal resembles an imaginary protection trigger.
Fig 4.
Start-up sequence, normal operation and restart sequence
7.1.2 Power-down mode
The power-down mode can be activated for very low standby power applications by
pulling the VVINSENSE < Vth(pd) level. The SSL8516T stops switching and safe restart
protection is activated. The high-voltage start-up current source is also disabled during
power-down and the SSL8516T does not restart until VVINSENSE is raised again.
During Power-down mode, all internal circuitry is disabled except for a voltage detection
circuit on the VINSENSE pin. This circuit is supplied by the HV pin and draws 12 A from
the HV pin for biasing.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
7 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
7.1.3 Supply management
All internal reference voltages are derived from a temperature compensated and trimmed
on-chip band gap circuit. Internal reference currents are derived from a temperature
compensated and trimmed on-chip current reference circuit.
7.1.4 Latch input
The LATCH pin is a general-purpose input pin which is used to switch off both converters.
The pin sources a current IO(LATCH) of 30.5 A. Switching of both converters is stopped
when VLATCH is < 494 mV. A latched protection is triggered. It can be reset by removing
the voltage from both the VCC and HV pins or by the fast latch reset function
(see Section 7.1.5).
At initial start-up, switching is prevented until the capacitor on the LATCH pin is charged
above 582 mV. No internal filtering is performed on this pin. An internal 1.75 V clamp
protects the pin from excessive voltages.
7.1.5 Fast latch reset
In a typical application, the mains can be interrupted briefly to reset the latched protection.
The bulk capacitor Cbulk does not have to discharge for this latched protection to reset.
When the VINSENSE voltage drops below 750 mV and is then raised to 860 mV, the
latched protection is reset.
The latched protection is also reset by removing both the voltage on the VCC and HV pins.
7.1.6 Overtemperature protection
An accurate internal temperature protection is provided in the IC. When the junction
temperature exceeds the thermal shut-down temperature, the IC stops switching. While
OTP is active, the capacitor CVCC is not recharged from the HV mains. If the VCC supply
voltage is not sufficient, the OTP circuit is supplied from the HV pin.
OTP is a safe restart protection.
7.2 Power factor correction circuit
The Power Factor Correction (PFC) circuit operates in Quasi-Resonant (QR) or
Discontinuous Conduction Mode (DCM) with valley switching. The next primary stroke is
only started when the previous secondary stroke has ended and the voltage across the
PFC MOSFET has reached the minimum value.
VPFCAUX is used to detect transformer demagnetization and the minimum voltage across
the external PFC MOSFET switch.
7.2.1 ton control (PFCCOMP pin)
The power factor correction circuit is operated in ton control. The resulting mains harmonic
reduction is well within the class-C lighting requirements.
VPFCCOMP determines the on-time of the PFC. The VVOSENSE is the transconductance
amplifier input which outputs current to the PFCCOMP pin. The regulation
VVOSENSE = 2.5 V. The network connected to the PFCCOMP pin and the
transconductance amplifier determine the dynamic behavior of the PFC control.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
8 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Operating near the PFC OVP level causes the PFC stage on-time to decrease rapidly to
zero.
To reduce the response time, in case of load variation, the PFCCOMP pin is clamped to a
minimum level of 1.19 V during PFC operation. Clamping prevents the on-time increasing
too much and improves the PFC response time when the load decreases again.
7.2.2 Valley switching and demagnetization (PFCAUX pin)
The PFC MOSFET is switched on after the transformer is demagnetized. Internal circuitry
connected to the PFCAUX pin detects the end of the secondary stroke. It also detects the
voltage across the PFC MOSFET. To reduce switching losses and
ElectroMagnetic Interference (EMI), the next stroke is started when the voltage across the
PFC MOSFET is at its minimum (valley switching).
If a demagnetization signal is not detected on the PFCAUX pin, the controller generates a
Zero-Current Signal (ZCS) 48 s after the last PFC MOSFET gate signal.
If valley signal is not detected on the PFCAUX pin, the controller generates a valley signal
4.2 s after demagnetization is detected.
To protect the internal circuitry during, for example, lightning events, add a 5 k series
resistor to the PFCAUX pin. To prevent incorrect switching due to external interference,
place the resistor close to the IC on the PCB.
7.2.3 Frequency limitation
To optimize the transformer and minimize switching losses, the switching frequency is
limited to fsw(PFC)max. If the frequency for quasi-resonant operation is above the fsw(PFC)max
limit, the system switches to DCM. The PFC MOSFET is only switched on at a minimum
voltage across the switch (valley switching).
7.2.4 Mains voltage compensation (VINSENSE pin)
The equation for the transfer function of a power factor corrector contains the square of
the mains input voltage. In a typical application, it results in a low bandwidth for low mains
input voltages.
To compensate for the influence of the mains input voltage, the SSL8516T contains a
correction circuit. The average input voltage is measured using the VINSENSE pin and
the information is fed to an internal compensation circuit. Using this compensation, it is
possible to keep the regulation loop bandwidth constant over the mains input range. This
feature gives a fast transient response on load steps while complying with class-C MHR
requirements.
In a typical application, a resistor and two capacitors connected to the PFCCOMP pin set
the regulation loop bandwidth.
7.2.5 Soft-start (PFCSENSE pin)
To prevent audible transformer noise at start-up or during hiccup, the soft-start function
slowly increases the transformer peak current. Place a capacitor CSS1 in parallel with
resistor RSS1 (see Figure 5) to implement a soft-start function. An internal current source
charges the capacitor to:
V PFCSENSE = I start soft PFC R SS1
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
(1)
© NXP Semiconductors N.V. 2014. All rights reserved.
9 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
The voltage is limited to Vstart(soft)PFC.
The start level and time constant of the increasing primary current level is externally
adjusted by changing the RSS1 and CSS1 values.
start soft PFC = 3 R SS1 C SS1
(2)
The charging current Istart(soft)PFC flows while the PFCSENSE pin voltage is < 0.5 V. If
VPFCSENSE exceeds 0.5 V, the soft-start current source starts limiting current Istart(soft)PFC.
When the PFC starts switching, the Istart(soft)PFC current source is switched off; see
Figure 5.
6
,VWDUW VRIW 3)& $
62)767$57
62)76723
&21752/
566
3)&6(16(
&66
56(16(
2&3
P9
DDD
Fig 5.
Soft start of the PFC
7.2.6 PFC switch-on/switch-off control
When the flyback converter output power (see Section 7.3) is low, the flyback converter
switches to FR mode. When the switching frequency of the flyback in
FR mode < fsw(fb)swoff(PFC) (53 kHz), the PFC circuit is switched off to maintain high
efficiency. Connect a capacitor to the PFCTIMER pin (see Section 7.2.7) to delay the PFC
switching off.
During low-power mode operation and start-up (when PFC is disabled, e.g. at no-load),
the PFCCOMP pin is clamped to a minimum voltage of 3.32 V or 1.18 V and a maximum
voltage of 3.75 V. The minimum clamp voltage depends on VVINSENSE. This voltage limits
the maximum power that is delivered when the PFC switches on again. The upper clamp
voltage ensures that the PFC returns from low-power mode to its normal regulation point
in a limited time.
In FR mode, when the flyback converter switching frequency exceeds
fsw(fb)swon(PFC) (73 kHz), the PFC circuit is switched on. If the flyback converter duty cycle
is > 50 % or VFBCTRL is > 3.75 V, the PFC circuit is also switched on.
7.2.7 PFC switch off delay (PFCTIMER pin)
When the flyback converter switching frequency in FR mode is < fsw(fb)swoff(PFC) (53 kHz),
the IC then outputs a 4.7 A current to the PFCTIMER pin. When VPFCTIMER reaches 3 V,
the PFC is switched off by performing a soft-stop.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
10 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
A switch discharges the PFCTIMER pin capacitor when the flyback controller operating
frequency is > fsw(fb)swon(PFC) (73 kHz). At the same moment, the PFC stage is also
switched on.
Connect a capacitor to the PFCTIMER pin (see Section 7.2.7) to prevent the PFC from
switching off due to a dynamic load that leads to repetitive crossing of fsw(fb)swoff(PFC) and
fsw(fb)swon(PFC). A 1 nF minimum capacitor value is recommended to prevent noise
influencing the PFC switch on/ switch off behavior.
The PFCTIMER pin capacitor is also discharged when PFC is on and the flyback
switching frequency is higher than 53 kHz. This feature prevents PFC on/off toggling
during dynamic loads causing the flyback to operate repetitively near fsw(fb)swoff(PFC) and
fsw(fb)swon(PFC).
It is also possible to control PFC switch-on and switch off externally. When VPFCTIMER is
driven below 1.03 V, the PFC stage is on. When the PFCTIMER pin voltage is driven
above 4.4 V, the PFC stage is switched off. The external control overrides the PFC stage
control by the flyback controller (see Figure 6).
The PFCTIMER pin has an internal clamp circuit starting around 10 V with a current
capability of 0.1 mA
ORZSRZHU
$
Nȍ
9
9
9
5
5
6
6
4
4
3)&7,0(5
Fig 6.
ORZSRZHUGHOD\
3)&RQ
DDD
PFC switch on and switch off using the PFCTIMER pin
7.2.8 Overcurrent protection (PFCSENSE pin)
The maximum peak current is limited cycle-by-cycle by sensing the voltage across an
external sense resistor, RSENSE1, on the source of the external MOSFET. The voltage is
measured using the PFCSENSE pin.
7.2.9 Mains undervoltage lockout/brownout protection (VINSENSE pin)
To prevent the PFC from operating at very low mains input voltages, VVINSENSE is sensed
continuously. When VVINSENSE drops below the Vstop(VINSENSE) level, switching of the PFC
is stopped.
7.2.10 Overvoltage protection (VOSENSE pin)
To prevent output overvoltage during load steps and mains transients, an overvoltage
protection circuit is built in.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
11 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
When VVOSENSE exceeds the VOVP(VOSENSE) level, switching of the PFC circuit is
prevented. Switching of the PFC restarts when the VOSENSE pin voltage drops below the
VOVP(VOSENSE) level again.
OVP is also triggered when the resistor between the VOSENSE pin and ground is open.
7.2.11 PFC open-loop protection (VOSENSE pin)
The PFC circuit does not start switching until the VVOSENSE pin is greater than the
Vth(start)(VOSENSE) level. This feature protects the application from open-loop and
VOSENSE short-circuit situations.
7.2.12 Driver (PFCDRIVER pin)
The driver circuit to the gate of the power MOSFET includes a current sourcing capability
of 500 mA at 2 V on the PFCDRIVER pin. It also includes a current sink capability of 1.2 A
at 10 V on the PFCDRIVER pin. These capabilities ensure fast switch-on and switch-off of
the power MOSFET for efficient operation.
7.3 Flyback controller
The SSL8516T includes a controller for a flyback converter. The flyback converter
operates in quasi-resonant or discontinuous conduction mode with valley switching. The
auxiliary winding of the flyback transformer provides demagnetization detection and
powers the IC after start-up.
7.3.1 Multimode operation
The SSL8516T flyback controller can operate in several modes; see Figure 7.
'&0
)5
45
OSN PLQ
IVZ IE
N+]
DGMXVW
3)&RII
3)&RQ
)5 )UHTXHQF\5HGXFWLRQ
'&0 'LVFRQWLQXRXV&RQGXFWLRQ0RGH
45 4XDVL5HVRQDQW
RXWSXWSRZHU
DDD
Fig 7.
Multimode operation flyback
At high output power the converter switches to quasi-resonant mode. The next converter
stroke starts after demagnetization of the transformer and detection of the valley. In
quasi-resonant mode switching losses are minimized. This minimization is achieved by
the converter only switching on when the voltage across the external MOSFET is at its
minimum (see Section 7.3.2).
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
12 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Valley switching is active in all operating modes.
To prevent high frequency operation at lower loads, the quasi-resonant operation switches
to discontinuous mode operation with valley skipping. When the frequency limit is
reached, the quasi-resonant operation changes to DCM with valley skipping. The
frequency limit reduces the MOSFET switch-on losses and conducted EMI.
At medium and low power levels, the controller enters Frequency Reduction (FR) mode. A
Voltage Controlled Oscillator (VCO) controls the frequency. During frequency reduction
mode, the primary peak current is kept at an adjustable minimal level to maintain a high
efficiency. Valley switching is also active in this mode.
In frequency reduction mode, the PFC controller switches off when the flyback switching
frequency has dropped to below 53 kHz and VPFCTIMER has reached 3 V. The flyback
maximum frequency changes linearly with the control VFBCTRL (see Figure 8). Hysteresis
is added to ensure a stable PFC switch-on and switch-off. In no-load operation, the
switching frequency is reduced to (almost) zero.
'&0
)5
45
IVZ IE
N+]
3)&RII
3)&RQ
45 4XDVL5HVRQDQW
'&0 'LVFRQWLQXRXV&RQGXFWLRQ0RGH
)5 )UHTXHQF\5HGXFWLRQ
9)%&75/ 9
DDD
Fig 8.
Flyback frequency control
7.3.2 Valley switching (HV pin)
A new cycle starts when the external MOSFET is switched on. VFBSENSE and VFBCTRL
determine the on-time. The MOSFET is then switched off and the secondary stroke starts
(see Figure 9). After the secondary stroke, the drain voltage shows an oscillation with a
frequency of approximately:
1
f = -------------------------------------------------- 2 Lp Cd
(3)
where Lp is the primary self-inductance of the flyback transformer and Cd is the
capacitance on the drain node.
When the secondary stroke ends and the internal oscillator voltage is high again, the
circuit waits for the lowest drain voltage before starting a new primary stroke.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
13 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Figure 9 shows the drain voltage, valley signal, secondary stroke signal and the internal
oscillator signal.
Valley switching allows high frequency operation because capacitive switching losses are
reduced (see Equation 4). High frequency operation makes small and cost-effective
magnetic components possible.
2
1
P = --- C d V f
2
(4)
SULPDU\
VWURNH
VHFRQGDU\
VWURNH
VHFRQGDU\
ULQJLQJ
GUDLQ
YDOOH\
VHFRQGDU\
VWURNH
RVFLOODWRU
DDD
(1) Start of a new cycle at lowest drain voltage.
(2) Start of a new cycle in a classical Pulse-Width Modulation (PWM) system without valley detection.
Fig 9.
Signals for valley switching
7.3.3 Current mode control (FBSENSE pin)
Current mode control is used for the flyback converter because of its good line regulation.
The FBSENSE pin senses the primary current across an external resistor and compares it
to an internal control voltage. The internal control voltage is proportional to VFBCTRL (see
Figure 10).
The FBSENSE pin outputs a current of 2.1 A. This current runs through the resistors
from the FBSENSE pin to the sense resistor RSENSE2 and creates an offset voltage.
Resistor RSS2 causes the offset voltage because RSENSE2 is relatively small. The minimum
flyback peak current is adjusted using this offset voltage. Adjusting the minimum peak
current level, changes the frequency reduction slope (see Figure 7).
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
14 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
9VHQVH IE PD[
P9
3)&RII
)%6(16(
RIIVHWYROWDJH
3)&RQ
6(16(UHVLVWRU
SHDNYROWDJH
)%6(16(
SHDNYROWDJH
IO\EDFN
)5PRGH
IO\EDFN
'&0RU45
P9
9)%&75/ 9
DDD
Fig 10. Flyback part peak current control
7.3.4 Demagnetization (FBAUX pin)
The system is always in QR or DCM. The internal oscillator does not start a new primary
stroke until the previous secondary stroke has ended.
Demagnetization features a cycle-by-cycle output short-circuit protection by immediately
lowering the frequency (longer off-time) and reducing the power level.
Demagnetization recognition is suppressed during the first tsup(xfmr_ring) time of 2.2 s.
This suppression can be necessary at low output voltages, during start-up and in
applications where the transformer has a large leakage inductance.
If the FBAUX pin is open-circuit or not connected, a fault condition is assumed and the
converter immediately stops. Operation restarts when the fault condition is removed.
7.3.5 Flyback control/time-out (FBCTRL pin)
The FBCTRL pin is connected to an internal voltage source of 7 V using an internal
13.2 k resistor. When VFBCTRL > 5.5 V, the resistor is disconnected. The pin is biased
with a 29 A current. When VFBCTRL > 7.75 V, a fault is assumed, switching is stopped and
a restart is made.
If a capacitor and resistor are connected in series to the pin, a time-out function is created
which protects against open control loop situations. See Figure 11 and Figure 12. The
time-out function is disabled by connecting a resistor (200 k) to ground on the FBCTRL
pin.
If the pin is short-circuited to ground, switching of the flyback controller is stopped.
Under normal operating conditions, the converter regulates the output voltage. VFBCTRL
varies between 0.54 V at minimum output power and 4.9 V at maximum output power.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
15 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
9
9
$
9
Nȍ
)%&75/
WLPHRXW
DDD
Fig 11. Time-out protection circuit
9
9
9)%&75/
RXWSXW
YROWDJH
LQWHQGHGRXWSXW
YROWDJHQRWUHDFKHG
ZLWKLQWLPHRXWWLPH
UHVWDUW
LQWHQGHGRXWSXW
YROWDJHUHDFKHG
ZLWKLQWLPHRXWWLPH
DDD
Fig 12. SSL8516T time-out protection (signals) and safe restart
7.3.6 Soft-start (FBSENSE pin)
To prevent audible transformer noise during start-up, the soft-start function slowly
increases the transformer peak current. Place a capacitor CSS2 in parallel with resistor
RSS2 (see Figure 13) to implement the soft-start function.
An internal current source charges the capacitor to:
V = I start soft fb R SS2
(5)
with a maximum of 0.55 V.
The start level and the time constant of the increasing primary current level can be
adjusted externally by changing the values of RSS2 and CSS2.
start soft fb = 3 R SS2 C SS2
(6)
The soft-start current Istart(soft)fb switches on when VCC reaches Vstartup. When the
VFBSENSE reaches 0.55 V, the flyback converter starts switching.
The charging current Istart(soft)fb flows when the VFBSENSE is < 0.55 V. If VFBSENSE exceeds
0.55 V, the soft-start current source starts limiting the current. After the flyback converter
has started, the soft-start current source is switched off.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
16 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
$ ,VWDUW VRIW IE
6
$
62)767$57
&21752/
566
)%6(16(
2&3
RFSOHYHO
&66
56(16(
DDD
Fig 13. Flyback soft-start
7.3.7 Maximum on-time
The flyback controller limits the on-time of the external MOSFET to 38.5 s. When the
on-time is longer than 38.5 s, the IC stops switching and enters the safe restart state.
7.3.8 Overvoltage protection (FBAUX pin)
An output OVP is implemented in the GreenChip series. In the SSL8516T, the auxiliary
voltage is sensed using the current flowing into the FBAUX pin during the secondary
stroke. The auxiliary winding voltage is a well-defined replica of the output voltage. An
internal filter averages voltage spikes.
An internal up-down counter prevents false OVP detection which can occur during ESD or
lightning events. The internal counter counts up by one when the output voltage exceeds
the OVP trip level within one switching cycle. The internal counter counts down by two
when the output voltage has not exceeded the OVP trip level in one switching cycle.
When the counter has reached six, the IC assumes a true overvoltage and triggers the
safe start protection
The demagnetization resistor, RFBAUX sets the output voltage Vo(OVP) at which the OVP
function trips:
Ns
V o OVP = ----------- I ovp FBAUX R FBAUX + V clamp FBAUX
N aux
(7)
where Ns is the number of secondary windings and Naux is the number of auxiliary
windings of the transformer. Current Iovp(FBAUX) is internally trimmed.
Accurate OVP detection is made possible by adjusting the value of RFBAUX to the turns
ratio of the transformer.
7.3.9 Overcurrent protection (FBSENSE pin)
The primary peak current in the transformer is measured accurately cycle-by-cycle using
the external sense resistor RSENSE2. The OCP circuit limits VFBSENSE to a level set by
VFBCTRL (see also Section 7.3.3). The OCP detection is suppressed during the
leading-edge blanking period, tleb (equals ton(fb)min td(FBDRIVER)), to prevent false
triggering due to switch-on spikes.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
17 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
WOHE
2&3OHYHO
9)%6(16(
W
DDD
Fig 14. OCP leading-edge blanking
7.3.10 Overpower protection
During the flyback converter primary stroke, the flyback converter input voltage is
measured by sensing the current that is drawn from the FBAUX pin.
The current information is used to limit the maximum flyback converter peak current and is
measured using the FBSENSE pin. The internal compensation is such, that a maximum
output power is obtained which is almost independent of the PFC output voltage.
The OPP curve is given in Figure 15.
9)%6(16(
P9
,)%$8; $
DDD
Fig 15. Overpower protection curve
7.3.11 Driver (FBDRIVER pin)
The driver circuit for the external power MOSFET gate includes a current sourcing
capability of 500 mA at 2 V on the FBDRIVER pin. It also includes a current sink capability
of 1.2 A at 10 V on the FBDRIVER pin. These capabilities ensure fast switch-on and
switch-off of the power MOSFET for efficient operation.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
18 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
8. Limiting values
Table 3.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
Min
Max
Unit
0.4
+38
V
0.4
+10
V
Voltages
VCC
supply voltage
VLATCH
voltage on pin LATCH
VFBCTRL
voltage on pin FBCTRL
0.4
+9
V
VPFCCOMP
voltage on pin PFCCOMP
0.4
+5
V
VVINSENSE
voltage on pin VINSENSE
current limited
0.4
+10
V
VVOSENSE
voltage on pin VOSENSE
current limited
0.4
+10
V
VPFCAUX
voltage on pin PFCAUX
25
+25
V
VFBSENSE
voltage on pin FBSENSE
current limited
0.4
+5
V
VPFCSENSE voltage on pin PFCSENSE
current limited
0.4
+5
V
VPFCTIMER voltage on pin PFCTIMER
current limited
0.4
+10
V
voltage on pin HV
0.4
+650
V
IFBCTRL
current on pin FBCTRL
3
0
mA
IFBAUX
current on pin FBAUX
1
+1
mA
IPFCSENSE
current on pin PFCSENSE
1
+10
mA
IFBSENSE
current on pin FBSENSE
1
+10
mA
IFBDRIVER
current on pin FBDRIVER
< 10 %
0.8
+2
A
< 10 %
0.8
+2
A
1
+0.1
mA
during start-up
and restart
-
8
mA
= 3 % due to
dV/dt on HV pin
15
+30
mA
Tamb < 75 C
VHV
current limited
Currents
IPFCDRIVER current on pin PFCDRIVER
IPFCTIMER
current on pin PFCTIMER
IHV
current on pin HV
General
Ptot
total power dissipation
-
0.6
W
Tstg
storage temperature
55
+150
C
Tj
junction temperature
40
+155
C
ESD
VESD
electrostatic discharge
voltage
human body
model
pins 1 to 14
[1]
2
2
kV
pin 16 (HV)
[1]
1.5
1.5
kV
500
500
V
charged device
model
[1]
SSL8516T
Product data sheet
Equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
19 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
9. Thermal characteristics
Table 4.
Thermal characteristics
Symbol
Parameter
Conditions
Typ
Unit
Rth(j-a)
thermal resistance from junction to ambient
in free air; JEDEC test board
127
K/W
Rth(j-c)
thermal resistance from junction to case
in free air; JEDEC test board
36
K/W
10. Characteristics
Table 5.
Characteristics
Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into
the IC; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VCC < Vtrip
0.9
Vth(UVLO) < VCC 75 V
Vtrip < VCC < Vth(UVLO)
4
5
6
mA
with auxiliary supply
-
-
1.5
A
in Power-down mode; VCC = 0 V
5
12
25
A
650
-
-
V
breakdown voltage
Supply voltage management (VCC pin)
Vtrip
trip voltage
0.5
0.6
0.7
V
Vstartup
start-up voltage
21.3
22.3
23.3
V
Vth(UVLO)
undervoltage lockout
threshold voltage
12.4
13.4
14.4
V
Vhys
hysteresis voltage
Vstartup Vth(UVLO)
8.3
8.9
9.5
V
Ich(low)
low charging current
VHV > 75 V
Ich(high)
ICC(oper)
high charging current
operating supply
current
VCC < Vtrip
1.15 1
0.85 mA
Vth(UVLO) < VCC < Vstartup
1.05 0.9
0.75 mA
VHV > 75 V; Vtrip < VCC < Vth(UVLO)
5.8
4.9
4
mA
Vth(UVLO) < VCC < Vstartup;
initial start-up
5.8
4.9
4
mA
no-load on pins FBDRIVER and
PFCDRIVER; VFBCTRL = 5 V;
fFB = fPFC = 100 kHz; = 30 %
2.45
2.7
2.95
mA
no-load on pins FBDRIVER and
PFCDRIVER; flyback switching;
VFBCTRL = 0.77 V; VPFCSENSE = 0 V
2.6
2.9
3.2
mA
ICC(prot)
protection supply
current
time-out protection triggered;
VHV = 0 V
0.3
0.45
0.6
mA
ICC(pd)
power-down mode
supply current
IC in power-down mode; VHV = 0 V
0.3
0.45
0.6
mA
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
20 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Table 5.
Characteristics …continued
Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into
the IC; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Input voltage sensing PFC (VINSENSE pin)
Vstop(VINSENSE)
stop voltage on pin
VINSENSE
0.86
0.89
0.92
V
Vstart(VINSENSE)
start voltage on pin
VINSENSE
1.12
1.16
1.20
V
Vflr
fast latch reset voltage active after Vth(UVLO) is detected
0.6
0.75
0.9
V
Vflr(hys)
hysteresis of fast latch
reset voltage
60
110
160
mV
II(VINSENSE)
input current on pin
VINSENSE
5
20
50
nA
Vth(sel)clmp
clamp select threshold on pin VINSENSE
voltage
1.9
2
2.1
V
Vth(sel)clmp(hys)
clamp select threshold
voltage hysteresis
60
100
140
mV
Vth(pd)
power-down threshold
voltage
285
385
485
mV
Vth(pd)exit
exit power-down
threshold voltage
335
460
585
mV
Vhys(pd)
power-down
hysteresis voltage
45
75
105
mV
VVINSENSE > Vstop(VINSENSE) after
Vstart(VINSENSE) is detected
VCC = 0 V
Loop compensation PFC (PFCCOMP pin)
gm
transconductance
VVOSENSE to IO(PFCCOMP)
57
77
97
A/V
IO(PFCCOMP)
output current on pin
PFCCOMP
VVOSENSE = 2 V; VPFCCOMP = 2.75 V
30
37
44
A
VVOSENSE = 3.3 V;
VPFCCOMP = 2.75 V
108
88
68
A
-
55
-
A
Ien(PFCCOMP)
enable current on pin
PFCCOMP
Vclamp(PFCCOMP)
clamp voltage on pin
PFCCOMP
Vton(PFCCOMP)zero
SSL8516T
Product data sheet
low-power mode; PFC off; initial
start-up; lower clamp voltage.
[1]
VINSENSE Vth(sel)clmp +
Vth(sel)clmp(hys) on pin VINSENSE;
VVOSENSE = 2 V
[2]
3.2
3.32
3.44
V
VINSENSE < Vth(sel)clmp on pin
VINSENSE; VVOSENSE = 2 V
[2]
1.06
1.18
1.30
V
upper clamp voltage
3.6
3.75
3.9
V
high-power mode; PFC on;
uni-directional source clamp;
IPFCCOMP = 30 A;
VVOSENSE = 2.5 V
1.09
1.19
1.29
V
3.4
3.5
3.6
V
zero on-time voltage
on pin PFCCOMP
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
21 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Table 5.
Characteristics …continued
Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into
the IC; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VVINSENSE = 3.3 V; VVOSENSE = 2 V;
VPFCCOMP = Vclamp(PFCCOMP)
(lower clamp)
3.6
4.7
5.8
s
VVINSENSE = 1 V; VVOSENSE = 2 V;
VPFCCOMP = Vclamp(PFCCOMP)
(lower clamp)
33
46
59
s
Pulse-width modulator PFC
ton(PFC)
PFC on-time
Output voltage sensing PFC (VOSENSE pin)
Vth(start)VOSENSE
start threshold voltage open-loop
on pin VOSENSE
0.45
0.5
0.55
V
Vth(stop)VOSENSE
threshold stop voltage
on pin VOSENSE
0.35
0.4
0.45
V
Vhys(VOSENSE)
hysteresis voltage on
pin VOSENSE
Vth(start)VOSENSE Vth(stop)VOSENSE
75
100
125
mV
Vreg(VOSENSE)
regulation voltage on
pin VOSENSE
for IO(PFCCOMP) = 0 A
2.475 2.5
2.525 V
ton = 0 s
2.59
2.62
2.65
V
50
25
5
nA
VOVP(VOSENSE)
Iprot(VOSENSE)
protection current on
pin VOSENSE
Overcurrent protection PFC (PFCSENSE pin)
Vsense(PFC)max
maximum PFC sense
voltage
V/t = 0 V/s
465
495
525
mV
td(PFCDRIVER)
delay time on pin
PFCDRIVER
VPFCSENSE pulse-stepping 400 mV
around Vsense(PFC)max
-
50
-
ns
tleb(PFC)
PFC leading edge
blanking time
VPFCSENSE = 0.75 V
230
290
350
ns
Iprot(PFCSENSE)
protection current on
pin PFCSENSE
50
-
5
nA
Soft-start PFC (PFCSENSE pin)
Istart(soft)PFC
PFC soft start current
73
60
47
A
Vstart(soft)PFC
PFC soft start voltage
enabling voltage
0.45
0.5
0.55
V
Vstop(soft)PFC
PFC soft stop voltage
disabling voltage
0.4
0.45
0.5
V
Oscillator PFC
fsw(PFC)max
maximum PFC
switching frequency
320
400
480
kHz
toff(PFC)min
minimum PFC off-time secondary stroke
0.8
1.1
1.4
s
Valley switching PFC (PFCAUX pin)
(V/t)vrec(PFC)
PFC valley recognition
voltage change with
time
-
-
1.7
V/s
tto(vrec)PFC
PFC valley recognition
time-out time
3
4.2
5.4
s
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
22 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Table 5.
Characteristics …continued
Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into
the IC; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Demagnetization management PFC (PFCAUX pin)
Vth(comp)PFCAUX
comparator threshold
voltage on pin
PFCAUX
125
90
55
mV
tto(demag)PFC
PFC demagnetization
time-out time
39
48
57
s
Iprot(PFCAUX)
protection current on
pin PFCAUX
VPFCAUX = 50 mV
75
-
5
nA
PFC off delay (PFCTIMER pin)
Isource(PFCTIMER)
source current on pin
PFCTIMER
VPFCTIMER = 2.5 V
5.4
4.7
4
A
Rsink(PFCTIMER)
sink resistance on pin
PFCTIMER
VPFCTIMER = 2.5 V
4
5.5
7
k
Vstart(PFCTIMER)
start voltage on pin
PFCTIMER
0.93
1.03
1.13
V
Vstop(PFCTIMER)
stop voltage on pin
PFCTIMER
2.85
3
3.15
V
Vth(off)PFCTIMER
switch-off threshold
voltage on pin
PFCTIMER
PFC override voltage
4.2
4.4
4.6
V
Driver (PFCDRIVER pin)
Isrc(PFCDRIVER)
source current on pin
PFCDRIVER
VPFCDRIVER = 2 V
-
0.5
-
A
Isink(PFCDRIVER)
sink current on pin
PFCDRIVER
VPFCDRIVER = 2.5 V
-
0.7
-
A
VO(PFCDRIVER)max
maximum output
voltage on pin
PFCDRIVER
10
11
12
V
279
300
321
A
60
90
120
mV
-
5
nA
OverVoltage Protection flyback (FBAUX pin)
Iovp(FBAUX)
overvoltage protection
current on pin FBAUX
Demagnetization management flyback (FBAUX pin)
Vth(comp)FBAUX
comparator threshold
voltage on pin FBAUX
Iprot(FBAUX)
protection current on
pin FBAUX
VFBAUX = 50 mV
65
Vclamp(FBAUX)
clamp voltage on pin
FBAUX
IFBAUX = 100 A
0.75 0.7
0.65 V
IFBAUX = 300 A
0.87
0.92
0.97
V
tsup(xfmr_ring)
transformer ringing
suppression time
1.7
2.2
2.7
s
32.5
38.5
44.5
s
Pulse width modulator flyback
ton(fb)max
SSL8516T
Product data sheet
maximum flyback
on-time
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
23 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Table 5.
Characteristics …continued
Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into
the IC; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
110
130
150
kHz
3.8
4
4.2
V
Oscillator flyback
fsw(fb)max
maximum flyback
switching frequency
Vstart(red)f
frequency reduction
start voltage
fsw(fb)swon(PFC)
PFC switch-on flyback
switching frequency
70
73
76
kHz
fsw(fb)swoff(PFC)
PFC switch-off flyback
switching frequency
50
53
56
kHz
Ven(PFC)FBCTRL
PFC enable voltage
on pin FBCTRL
3.4
3.75
4.1
V
fsw(fb)VCO
VCO flyback switching VFBCTRL = 2.8 V
frequency
VFBCTRL = 0.77 V
45
53
61
kHz
16
20
24
kHz
flyback switch-off
voltage on pin
FBCTRL
0.4
0.54
0.68
V
4.6
4.9
5.2
V
Vswoff(fb)FBCTRL
transfer from DCM/QR to FR mode
override voltage
Peak current control flyback (FBCTRL pin)
VFBCTRL
voltage on pin
FBCTRL
for maximum flyback peak current
Vto(FBCTRL)
time-out voltage on
pin FBCTRL
enable voltage
5.3
5.5
5.7
V
trip voltage
7.3
7.75
8.2
V
output current on pin
FBCTRL
VFBCTRL = 0 V
0.75 0.6
0.45 mA
VFBCTRL = 4.5 V
0.3
0.24
0.18 mA
IO(FBCTRL)
Ito(FBCTRL)
time-out current on pin VFBCTRL = 6 V
FBCTRL
35
29
23
A
Rint(FBCTRL)
internal resistance on
pin FBCTRL
9.8
13.2
16.5
k
Valley switching flyback (HV pin)
(V/t)vrec(fb)
flyback valley
recognition voltage
change with time
[3]
75
-
+75
V/s
td(vrec-swon)
valley recognition to
switch-on delay time
[3]
-
75
-
ns
75
60
45
A
0.5
0.55
0.6
V
Soft-start flyback (FBSENSE pin)
Istart(soft)fb
flyback soft start
current
Vstart(soft)fb
flyback soft start
voltage
enable voltage
OverCurrent Protection (OCP) flyback (FBSENSE pin)
Vsense(fb)max
maximum flyback
sense voltage
V/t = 0 V/s
525
545
565
mV
Vsense(fb)min
minimum flyback
sense voltage
V/t = 0 V/s
221
232
243
mV
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
24 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Table 5.
Characteristics …continued
Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into
the IC; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
td(FBDRIVER)
delay time on pin
FBDRIVER
VFBSENSE pulse-stepping 400 mV
around Vsense(fb)max
-
80
-
ns
ton(fb)min
minimum flyback
on-time
VFBCRTL = 3 V; VFBSENSE = 0.75 V
280
340
400
ns
Iadj(FBSENSE)
adjust current on pin
FBSENSE
2.29 2.1
1.91 A
IFBAUX = 80 A
525
545
565
mV
IFBAUX = 120 A
495
540
565
mV
IFBAUX = 240 A
400
445
490
mV
IFBAUX = 360 A
345
400
455
mV
OverPower Protection (OPP) flyback (FBSENSE pin)
Vsense(fb)max
V/t = 0 V/s
maximum flyback
sense voltage
Driver (FBDRIVER pin)
Isrc(FBDRIVER)
source current on pin
FBDRIVER
VFBDRIVER = 2 V
-
0.5
-
A
Isink(FBDRIVER)
sink current on pin
FBDRIVER
VFBDRIVER = 2.5 V
-
0.7
-
A
VO(FBDRIVER)(max)
maximum output
voltage on pin
FBDRIVER
10
11
12
V
469
494
519
mV
LATCH input (LATCH pin)
Vprot(LATCH)
protection voltage on
pin LATCH
IO(LATCH)
output current on pin
LATCH
Vprot(LATCH) < VLATCH < Voc(LATCH)
32.5 30.5
28.5 A
Ven(LATCH)
enable voltage on pin
LATCH
at start-up
552
582
612
mV
Vhys(LATCH)
hysteresis voltage on
pin LATCH
Ven(LATCH) Vprot(LATCH)
68
88
108
mV
Voc(LATCH)
open-circuit voltage on
pin LATCH
-
1.75
-
V
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
25 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Table 5.
Characteristics …continued
Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into
the IC; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
135
145
155
C
-
10
-
C
Temperature protection
Tpl(IC)
IC protection level
temperature
Tpl(IC)hys
hysteresis of IC
protection level
temperature
[3]
[1]
A typical application with a compensation network on the PFCCOMP pin, such as the example in Figure 3.
[2]
The clamp voltage on the PFCCOMP pin is dependent on the VINSENSE voltage. When the VVINSENSE rises above
Vth(sel)clmp + Vth(sel)clmp(hys), the high clamp level is active. When the voltage on the VINSENSE pin drops below the Vth(sel)clmp level
again, the low clamp level is active.
[3]
Guaranteed by design.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
26 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
11. Application information
An LED driver with the SSL8516T consists of a PFC circuit and a flyback converter (see
Figure 16).
Capacitor CVCC buffers the IC supply voltage. The IC supply is charged from the high
voltage rectified mains during start-up and the auxiliary winding of the flyback converter
during operation. Sense resistors RSENSE1 and RSENSE2 convert the current through the
MOSFETs S1 and S2 into a voltage on the PFCSENSE and FBSENSE pins. The RSENSE1
and RSENSE2 values define the maximum primary peak current in MOSFETs S1 and S2.
In the example, the LATCH pin is connected to a Negative Temperature Coefficient (NTC)
resistor. The protection is activated when the resistance drops below the value as
calculated in Equation 8:
V prot LATCH
------------------------------- = 16.2 k
I O LATCH
(8)
Capacitor CTIMEOUT is connected to the FBCTRL pin. RLOOP ensures that the time-out
capacitor does not interfere with the flyback regulation control loop.
RS1 and RS2 prevent that the soft-start capacitors CSS1 and CSS2 are charged during
normal operation due to negative voltage spikes across the sense resistors.
Resistor RAUX1 protects the IC from damage during lightning events.
RS3 and RCOMP can be used to lower the PFC on/off power level. The minimum and
maximum peak current ratio increase. So, the PFC switch-on and switch-off power level
decreases.
RDRV1 and RDRV2 prevent that the internal MOSET drivers are damaged due to, for
example, power MOSFET avalanche.
Depending on the drain voltage maximum rating of MOSFET S2, the HV pin of the IC can
either be connected to the center tap of the flyback transformer or to the drain of MOSFET
S2.
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
27 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
'
'
7U
/2$'
7U
&
5
5'59
9PDLQV
&EXON
&287
6
5
&66
'
566
56(16(
5
5&203
4
5
5
5
56
5$8;
5
&
3)&$8;
5
&
5
3)&&203
9,16(16(
5
&
)%&75/
)%'5,9(5
+9
&7+'
926(16(
5
3)&6(16(
3)&'5,9(5
5'59
6
,&
&66
5
&
)%6(16( 56
)%$8;
566
5)%$8;
56
56(16(
5
5
,&
5/223
*1'
'
9&&
/$7&+
&9&&
3)&7,0(5
8
&7,0(287
&3)&7,0(5
&
517&
5
&
DDD
(1) In the application, the HV pin of the IC can either be connected to the center tap of the flyback transformer or to the drain of
MOSFET S2.
Fig 16. SSL8516T typical application diagram
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
28 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
12. Package outline
62 SODVWLFVPDOORXWOLQHSDFNDJH OHDGV ERG\ZLGWK PP
627
'
(
$
;
F
\
+(
Y 0 $
=
4
$
$
$
$
SLQLQGH[
ș
/S
/
H
Z 0
ES
GHWDLO;
PP
VFDOH
',0(16,216 LQFKGLPHQVLRQVDUHGHULYHGIURPWKHRULJLQDOPPGLPHQVLRQV
81,7
$
PD[
$
$
$
ES
F
'
(
H
+(
/
/S
4
Y
Z
\
=
PP
LQFKHV
ș
R
R
1RWH
3ODVWLFRUPHWDOSURWUXVLRQVRIPP LQFK PD[LPXPSHUVLGHDUHQRWLQFOXGHG
5()(5(1&(6
287/,1(
9(56,21
,(&
-('(&
627
(
06
-(,7$
(8523($1
352-(&7,21
,668('$7(
Fig 17. Package outline SOT109-1 (SO16)
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
29 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
13. Revision history
Table 6.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
SSL8516T v.1
20140505
Product data sheet
-
-
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
30 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
14. Legal information
14.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
14.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
14.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
SSL8516T
Product data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
31 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
14.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
GreenChip — is a trademark of NXP Semiconductors N.V.
15. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
SSL8516T
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 5 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
32 of 33
SSL8516T
NXP Semiconductors
Greenchip PFC and flyback controller
16. Contents
1
2
2.1
2.2
2.3
2.4
2.5
3
4
5
6
6.1
6.2
7
7.1
7.1.1
7.1.2
7.1.3
7.1.4
7.1.5
7.1.6
7.2
7.2.1
7.2.2
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 2
Distinctive features . . . . . . . . . . . . . . . . . . . . . . 2
Green features . . . . . . . . . . . . . . . . . . . . . . . . . 2
PFC green features . . . . . . . . . . . . . . . . . . . . . 2
Flyback green features . . . . . . . . . . . . . . . . . . . 2
Protection features . . . . . . . . . . . . . . . . . . . . . . 2
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pinning information . . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
Functional description . . . . . . . . . . . . . . . . . . . 5
General control . . . . . . . . . . . . . . . . . . . . . . . . . 5
Start-up and UnderVoltage LockOut (UVLO) . . 5
Power-down mode . . . . . . . . . . . . . . . . . . . . . . 7
Supply management. . . . . . . . . . . . . . . . . . . . . 8
Latch input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Fast latch reset . . . . . . . . . . . . . . . . . . . . . . . . . 8
Overtemperature protection . . . . . . . . . . . . . . . 8
Power factor correction circuit . . . . . . . . . . . . . 8
ton control (PFCCOMP pin). . . . . . . . . . . . . . . . 8
Valley switching and demagnetization
(PFCAUX pin) . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7.2.3
Frequency limitation . . . . . . . . . . . . . . . . . . . . . 9
7.2.4
Mains voltage compensation (VINSENSE pin). 9
7.2.5
Soft-start (PFCSENSE pin). . . . . . . . . . . . . . . . 9
7.2.6
PFC switch-on/switch-off control . . . . . . . . . . 10
7.2.7
PFC switch off delay (PFCTIMER pin) . . . . . . 10
7.2.8
Overcurrent protection (PFCSENSE pin) . . . . 11
7.2.9
Mains undervoltage lockout/brownout
protection (VINSENSE pin) . . . . . . . . . . . . . . 11
7.2.10
Overvoltage protection (VOSENSE pin) . . . . . 11
7.2.11
PFC open-loop protection (VOSENSE pin) . . 12
7.2.12
Driver (PFCDRIVER pin) . . . . . . . . . . . . . . . . 12
7.3
Flyback controller . . . . . . . . . . . . . . . . . . . . . . 12
7.3.1
Multimode operation . . . . . . . . . . . . . . . . . . . . 12
7.3.2
Valley switching (HV pin) . . . . . . . . . . . . . . . . 13
7.3.3
Current mode control (FBSENSE pin) . . . . . . 14
7.3.4
Demagnetization (FBAUX pin) . . . . . . . . . . . . 15
7.3.5
Flyback control/time-out (FBCTRL pin) . . . . . 15
7.3.6
Soft-start (FBSENSE pin) . . . . . . . . . . . . . . . . 16
7.3.7
Maximum on-time . . . . . . . . . . . . . . . . . . . . . . 17
7.3.8
Overvoltage protection (FBAUX pin) . . . . . . . 17
7.3.9
Overcurrent protection (FBSENSE pin) . . . . . 17
7.3.10
Overpower protection . . . . . . . . . . . . . . . . . . . 18
7.3.11
8
9
10
11
12
13
14
14.1
14.2
14.3
14.4
15
16
Driver (FBDRIVER pin) . . . . . . . . . . . . . . . . .
Limiting values . . . . . . . . . . . . . . . . . . . . . . . .
Thermal characteristics . . . . . . . . . . . . . . . . .
Characteristics . . . . . . . . . . . . . . . . . . . . . . . .
Application information . . . . . . . . . . . . . . . . .
Package outline. . . . . . . . . . . . . . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . .
Legal information . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information . . . . . . . . . . . . . . . . . . . .
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
19
20
20
27
29
30
31
31
31
31
32
32
33
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP Semiconductors N.V. 2014.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 5 May 2014
Document identifier: SSL8516T
工商网监
湘ICP备2023018690号
