TJF1051T/3,118

TJF1051 High-speed CAN transceiver Rev. 5 — 13 July 2016 Product data sheet 1. General description The TJF1051 is a high-speed CAN transceiver that provides an interface between a Controller Area Network (CAN) protocol controller and the physical two-wire CAN bus. The transceiver is designed for high-speed CAN industrial applications, providing differential transmit and receive capability to (a microcontroller with) a CAN protocol controller. The TJF1051 belongs to the third generation of high-speed CAN transceivers from NXP Semiconductors, offering significant improvements over first- and second-generation devices such as the TJA1050. It offers improved ElectroMagnetic Compatibility (EMC) and ElectroStatic Discharge (ESD) performance, and also features ideal passive behavior to the CAN bus when the supply voltage is off. The TJF1051T/3 can be interfaced directly to microcontrollers with supply voltages from 3 V to 5 V. The TJF1051 implements the CAN physical layer as defined in the current ISO11898 standard (ISO11898-2:2003, ISO11898-5:2007) and the pending updated version of ISO 11898-2:2016. Pending the release of the updated version of ISO11898-2:2016 including CAN FD and SAE J2284-4/5, additional timing parameters defining loop delay symmetry are specified. This implementation enables reliable communication in the CAN FD fast phase at data rates up to 5 Mbit/s. These features make the TJF1051 an excellent choice for all types of HS-CAN networks, in nodes that do not require a standby mode with wake-up capability via the bus. 2. Features and benefits 2.1 General     Fully ISO 11898-2:2003 compliant Timing guaranteed for data rates up to 5 Mbit/s in the CAN FD fast phase Low ElectroMagnetic Emission (EME) and high ElectroMagnetic Immunity (EMI) VIO input on the TJF1051T/3 allows for direct interfacing with 3 V to 5 V microcontrollers  Dark green product (halogen free and Restriction of Hazardous Substances (RoHS) compliant) 2.2 Low-power management  Functional behavior predictable under all supply conditions  Transceiver disengages from the bus when not powered up (zero load) TJF1051 NXP Semiconductors High-speed CAN transceiver 2.3 Protection     High ESD handling capability on the bus pins Transmit Data (TXD) dominant time-out function Undervoltage detection on pins VCC and VIO Thermally protected 3. Quick reference data Table 1. Quick reference data Symbol Parameter Conditions Min Typ Max Unit VCC supply voltage 4.5 - 5.5 V VIO supply voltage on pin VIO 2.8 - 5.5 V Vuvd(VCC) undervoltage detection voltage on pin VCC 3.5 - 4.5 V Vuvd(VIO) undervoltage detection voltage on pin VIO 1.3 2.0 2.7 V ICC supply current Silent mode 0.1 1 2.5 mA Normal mode; bus recessive 2.5 5 10 mA Normal mode; bus dominant 20 50 70 mA recessive; VTXD = VIO 10 80 250 A dominant; VTXD = 0 V 50 350 500 A supply current on pin VIO IIO Normal and Silent modes VESD electrostatic discharge voltage 8 - +8 kV VCANH voltage on pin CANH 58 - +58 V VCANL voltage on pin CANL 58 - +58 V HBM on pins CANH and CANL 4. Ordering information Table 2. Ordering information Type number Package Name Description Version TJF1051T SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 TJF1051T/3[1] SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 [1] TJF1051T/3 with VIO pin. TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 2 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 5. Block diagram VIO(1) VCC 5 3 VCC TJF1051 TEMPERATURE PROTECTION VIO TXD S RXD (1) 7 1 TIME-OUT 8 MODE CONTROL 4 SLOPE CONTROL AND DRIVER 6 CANH CANL DRIVER 2 GND 015aaa099 (1) In the TJF1051T, the VIO input is connected internally to VCC. Fig 1. TJF1051 Product data sheet Block diagram All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 3 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 6. Pinning information 6.1 Pinning 8 S 7 CANH 3 6 CANL 4 5 VIO 8 S TXD 1 7 CANH GND 2 3 6 CANL VCC 4 5 n.c. RXD TXD 1 GND 2 VCC RXD TJF1051T TJF1051T/3 015aaa395 a. TJF1051T Fig 2. 015aaa100 b. TJF1051T/3 Pin configuration diagrams 6.2 Pin description TJF1051 Product data sheet Table 3. Pin description Symbol Pin Description TXD 1 transmit data input GND 2 ground VCC 3 supply voltage RXD 4 receive data output; reads out data from the bus lines n.c. 5 not connected; in TJF1051T VIO 5 supply voltage for I/O level adapter; TJF1051T/3 only CANL 6 LOW-level CAN bus line CANH 7 HIGH-level CAN bus line S 8 Silent mode control input All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 4 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 7. Functional description The TJF1051 is a stand-alone high-speed CAN transceiver with Silent mode. It combines the functionality of the TJA1050 transceiver with improved EMC and ESD handling capability. Improved slope control and high DC handling capability on the bus pins provides additional application flexibility. The TJF1051T/3 allows for direct interfacing to microcontrollers with supply voltages down to 3 V. 7.1 Operating modes The TJF1051 supports two operating modes, Normal and Silent. The operating mode is selected via pin S. See Table 4 for a description of the operating modes under normal supply conditions. Table 4. Operating modes Mode Inputs Normal Silent Outputs Pin S Pin TXD CAN driver Pin RXD LOW LOW dominant active[1] LOW HIGH recessive active[1] HIGH X[2] recessive active[1] [1] LOW if the CAN bus is dominant, HIGH if the CAN bus is recessive. [2] X = don't care. 7.1.1 Normal mode A LOW level on pin S selects Normal mode. In this mode, the transceiver is able to transmit and receive data via bus lines CANH and CANL (see Figure 1 for the block diagram). The differential receiver converts the analog data on the bus lines into digital data which is output to pin RXD. The slopes of the output signals on the bus lines are controlled internally and are optimized in a way that guarantees the lowest possible EME levels. 7.1.2 Silent mode A HIGH level on pin S selects Silent mode. In Silent mode the transmitter is disabled, releasing the bus pins to recessive state. All other IC functions, including the receiver, continue to operate as in Normal mode. Silent mode can be used to prevent a faulty CAN controller from disrupting all network communications. 7.2 Fail-safe features 7.2.1 TXD dominant time-out function A ‘TXD dominant time-out’ timer is started when pin TXD is set LOW. If the LOW state on pin TXD persists for longer than tto(dom)TXD, the transmitter is disabled, releasing the bus lines to recessive state. This function prevents a hardware and/or software application failure from driving the bus lines to a permanent dominant state (blocking all network communications). The TXD dominant time-out timer is reset when pin TXD is set HIGH. The TXD dominant time-out time also defines the minimum possible bit rate of 20 kbit/s. TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 5 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 7.2.2 Internal biasing of TXD and S input pins Pin TXD has an internal pull-up to VIO and pin S has an internal pull-down to GND. This ensures a safe, defined state in case one (or both) of these pins is left floating. 7.2.3 Undervoltage detection on pins VCC and VIO Should VCC or VIO drop below their respective undervoltage detection levels (Vuvd(VCC) and Vuvd (VIO); see Table 7), the transceiver will switch off and disengage from the bus (zero load) until VCC and VIO have recovered. 7.2.4 Overtemperature protection The output drivers are protected against overtemperature conditions. If the virtual junction temperature exceeds the shutdown junction temperature, Tj(sd), the output drivers will be disabled until the virtual junction temperature falls below Tj(sd) and TXD becomes recessive again. Including the TXD condition ensures that output driver oscillations due to temperature drift are avoided. 7.3 VIO supply pin (TJF1051T/3) Pin VIO on the TJF1051T/3 should be connected to the microcontroller supply voltage (see Figure 5). This adjusts the signal levels on pins TXD, RXD and S to the I/O levels of the microcontroller. In the TJF1051T, the VIO input is internally connected to VCC. This sets the signal levels of pins TXD, RXD and S to levels compatible with 5 V microcontrollers. 8. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are referenced to GND. Symbol Parameter x[1] Conditions Min Max Unit on pins CANH, CANL 58 +58 V on any other pin 0.3 +7 V 27 +27 V pins CANH and CANL 8 +8 kV any other pin 4 +4 kV 300 +300 V 40 +125 C 55 +150 C Vx voltage on pin V(CANH-CANL) voltage between pin CANH and pin CANL VESD electrostatic discharge voltage Human Body Model (HBM); 100 pF, 1.5 k Machine Model (MM); 200 pF, 0.75 H, 10  [2] [3] any pin Tvj virtual junction temperature Tstg storage temperature [4] [1] The device can sustain voltages up to the specified values over the product lifetime, provided applied voltages (including transients) never exceed these values. [2] According to AEC-Q100-002. [3] According to AEC-Q100-003. [4] In accordance with IEC 60747-1. An alternative definition of virtual junction temperature is: Tvj = Tamb + P  Rth(vj-a), where Rth(vj-a) is a fixed value to be used for the calculation of Tvj. The rating for Tvj limits the allowable combinations of power dissipation (P) and ambient temperature (Tamb). TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 6 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 9. Thermal characteristics Table 6. Thermal characteristics According to IEC 60747-1. Symbol Parameter Conditions Value Unit Rth(vj-a) thermal resistance from virtual junction to ambient in free air 120 K/W 10. Static characteristics Table 7. Static characteristics Tamb = 40 C to +105 C; VCC = 4.5 V to 5.5 V; VIO = 2.8 V to 5.5 V[2]; RL = 60 ; unless otherwise specified; all voltages are defined with respect to ground; positive currents flow into the device[1]. Symbol Parameter Conditions Min Typ Max Unit 4.5 - 5.5 V 0.1 1 2.5 mA recessive 2.5 5 10 mA dominant; VTXD = 0 V 20 50 70 mA 3.5 - 4.5 V 2.8 - 5.5 V recessive; VTXD = VIO[3] 10 80 250 A dominant; VTXD = 0 V 50 350 500 A 1.3 2.0 2.7 V Supply; pin VCC VCC supply voltage ICC supply current Silent mode Normal mode Vuvd(VCC) undervoltage detection voltage on pin VCC I/O level adapter supply; pin VIO[2] VIO supply voltage on pin VIO IIO supply current on pin VIO Vuvd(VIO) Normal and Silent modes undervoltage detection voltage on pin VIO Mode control input; pin S VIH HIGH-level input voltage VIL LOW-level input voltage IIH HIGH-level input current IIL LOW-level input current [4] VS = 0 V 0.7VIO[3] - VIO + 0.3[3] V 0.3 - +0.3VIO[3] V 1 4 10 A 1 0 +1 A CAN transmit data input; pin TXD VIH HIGH-level input voltage VIL LOW-level input voltage IIH HIGH-level input current IIL LOW-level input current Ci input capacitance 0.7VIO[3] - VIO + 0.3[3] V 0.3 - +0.3VIO[3] V VTXD = VIO[3] 5 0 +5 A Normal mode; VTXD = 0 V 260 150 30 A - 5 10 pF [4] CAN receive data output; pin RXD IOH HIGH-level output current VRXD = VIO  0.4 V[3] 8 3 1 mA IOL LOW-level output current VRXD = 0.4 V; bus dominant 2 5 12 mA TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 7 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver Table 7. Static characteristics …continued Tamb = 40 C to +105 C; VCC = 4.5 V to 5.5 V; VIO = 2.8 V to 5.5 V[2]; RL = 60 ; unless otherwise specified; all voltages are defined with respect to ground; positive currents flow into the device[1]. Symbol Parameter Conditions Min Typ Max Unit pin CANH; RL = 50  to 65  2.75 3.5 4.5 V pin CANL; RL = 50  to 65  0.5 1.5 2.25 V 400 0 +400 mV 0.9VCC - 1.1VCC V VTXD = 0 V; t < tto(dom)TXD; VCC = 4.75 V to 5.25 V; RL = 50 to 65  1.5 - 3 V VTXD = 0 V; t < tto(dom)TXD; VCC = 4.75 V to 5.25 V; RL = 45 to 70  1.4 - 3.3 V VTXD = 0 V; t < tto(dom)TXD; VCC = 4.75 V to 5.25 V; RL = 2240  1.5 - 5 V 50 - +50 mV Bus lines; pins CANH and CANL VO(dom) dominant output voltage VTXD = 0 V; t < tto(dom)TXD Vdom(TX)sym = VCC  VCANH  VCANL Vdom(TX)sym transmitter dominant voltage symmetry VTXsym VO(dif) transmitter voltage symmetry VTXsym = VCANH + VCANL; fTXD = 250 kHz; CSPLIT = 4.7 nF differential output voltage [5] [6] dominant; Normal mode recessive Normal mode: VTXD = VIO[3]; no load VO(rec) recessive output voltage Normal and Silent modes; VTXD = VIO[3]; no load 2 0.5VCC 3 V Vth(RX)dif differential receiver threshold voltage Normal and Silent modes 12 V  VCANL  +12 V; 12 V  VCANH  +12 V 0.5 0.7 0.9 V Vrec(RX) receiver recessive voltage Normal/Silent mode; 12 V  VCANL  +12 V; 12 V  VCANH  +12 V 3 - +0.5 V Vdom(RX) receiver dominant voltage Normal/Silent mode; 12 V  VCANL  +12 V; 12 V v VCANH  +12 V 0.9 - 8.0 V Vhys(RX)dif differential receiver hysteresis voltage Normal and Silent modes 12 V  VCANL  +12 V; 12 V  VCANH  +12 V 50 120 400 mV IO(sc)dom dominant short-circuit output current VTXD = 0 V; t < tto(dom)TXD; VCC = 5 V 120 70 40 mA 40 70 120 mA IO(sc)rec recessive short-circuit output current Normal and Silent modes; VTXD = VCC; VCANH = VCANL = 27 V to +32 V 5 - +5 mA IL leakage current VCC = VIO = 0 V or VCC = VIO = shorted to ground via 47 k; VCANH = VCANL = 5 V 5 0 +5 A Ri input resistance 9 15 28 k pin CANH; VCANH = 3 V to +40 V pin CANL; VCANL = 3 V to +40 V TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 8 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver Table 7. Static characteristics …continued Tamb = 40 C to +105 C; VCC = 4.5 V to 5.5 V; VIO = 2.8 V to 5.5 V[2]; RL = 60 ; unless otherwise specified; all voltages are defined with respect to ground; positive currents flow into the device[1]. Symbol Parameter Conditions Min Typ Max Unit Ri input resistance deviation between VCANH and VCANL 3 0 +3 % Ri(dif) differential input resistance 19 30 52 k Ci(cm) common-mode input capacitance - - 20 pF Ci(dif) differential input capacitance - - 10 pF - 190 - C Temperature protection Tj(sd) shutdown junction temperature [1] All parameters are guaranteed over the virtual junction temperature range by design. Factory testing uses correlated test conditions to cover the specified temperature and power supply voltage range. [2] Only the TJF1051T/3 has a VIO pin; in the TJF1051T, the VIO input is internally connected to VCC. [3] VIO = VCC for the non-VIO product variants TJF1051T [4] Maximum value assumes VCC < VIO; if VCC > VIO, the maximum value will be VCC + 0.3 V. [5] Not tested in production; guaranteed by design. [6] The test circuit used to measure the bus output voltage symmetry (which includes CSPLIT) is shown in Figure 7. TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 9 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 11. Dynamic characteristics Table 8. Dynamic characteristics Tvj = 40 C to +150 C; VCC = 4.5 V to 5.5 V; VIO = 2.8 V to 5.5 V[1]; RL = 60  unless specified otherwise. All voltages are defined with respect to ground. Positive currents flow into the IC.[2] Symbol Parameter Conditions Min Typ Max Unit Transceiver timing; pins CANH, CANL, TXD and RXD; see Figure 6 and Figure 3 td(TXD-busdom) delay time from TXD to bus dominant Normal mode - 65 - ns td(TXD-busrec) delay time from TXD to bus recessive Normal mode - 90 - ns td(busdom-RXD) delay time from bus dominant to RXD Normal and Silent modes - 60 - ns td(busrec-RXD) delay time from bus recessive to RXD Normal and Silent modes - 65 - ns td(TXDL-RXDL) delay time from TXD LOW to RXD LOW Normal mode: versions with VIO pin 40 - 250 ns Normal mode: other versions 40 - 220 ns Normal mode: versions with VIO pin 40 - 250 ns Normal mode: other versions 40 - 220 ns td(TXDH-RXDH) tbit(bus) tbit(RXD) trec tto(dom)TXD delay time from TXD HIGH to RXD HIGH transmitted recessive bit width bit time on pin RXD receiver timing symmetry TXD dominant time-out time tbit(TXD) = 500 ns [3] 435 - 530 ns tbit(TXD) = 200 ns [3] 155 - 210 ns tbit(TXD) = 500 ns [3] 400 - 550 ns tbit(TXD) = 200 ns [3] 120 - 220 ns tbit(TXD) = 500 ns 65 - +40 ns tbit(TXD) = 200 ns 45 - +15 ns VTXD = 0 V; Normal mode 0.3 1 5 ms [1] Only TJF1051T/3 and TJF1051TK/3 have a VIO pin. In transceivers without a VIO pin, the VIO input is internally connected to VCC. [2] All parameters are guaranteed over the virtual junction temperature range by design. Factory testing uses correlated test conditions to cover the specified temperature and power supply voltage range. [3] See Figure 4. TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 10 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver +,*+ 7;' 97;' 97;' /2: &$1+ &$1/ GRPLQDQW 9 92GLIEXV 9 UHFHVVLYH +,*+ 9,2 5;' 9,2 /2: WG7;'EXVGRP WG7;'EXVUHF WGEXVUHF5;' WGEXVGRP5;' WG7;'/5;'/ WG7;'+5;'+ DDD (1) VIO = VCC in non-VIO product variant TJF1051T. Fig 3. CAN transceiver timing diagram  7;'   [WELW7;' WELW7;' 9 92GLI 9 WELWEXV  5;'  WELW5;' DDD Fig 4. TJF1051 Product data sheet Loop delay symmetry timing diagram All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 11 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 12. Application information 12.1 Application diagram %$7 9 9 9,2 9&& &$1+ &$1+ 9'' 6 7-)7 7;' 5;' 3\\ 7; 0,&52 &21752//(5 5; &$1/ &$1/ *1' *1' DDD Fig 5. Typical application of the TJF1051T/3 12.2 Application hints Further information on the application of the TJF1051 can be found in NXP application hints AH1014 Application Hints - Standalone high speed CAN transceiver TJA1042/TJA1043/TJA1048/TJA1051. TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 12 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 13. Test information +5 V 47 µF 100 nF VIO(1) VCC TXD CANH TJF1051 RXD RL 100 pF CANL GND S 15 pF 015aaa103 (1) In the TJF1051T/3, pin VIO connected to VCC. Fig 6. Timing test circuit for CAN transceiver 9,2 9&& 7;'     &$1+ ȍ I N+] 7-) 5;'  &63/,7 Q)  ȍ &$1/  *1' DDD Fig 7. TJF1051 Product data sheet Test circuit for measuring transceiver driver symmetry All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 13 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 14. Package outline 62SODVWLFVPDOORXWOLQHSDFNDJHOHDGVERG\ZLGWKPP 627 ' ( $ ; F \ +( Y 0 $ =   4 $ $ $  $ SLQLQGH[ ș /S  /  H GHWDLO; Z 0 ES   PP VFDOH ',0(16,216LQFKGLPHQVLRQVDUHGHULYHGIURPWKHRULJLQDOPPGLPHQVLRQV 81,7 $ PD[ $ $ $ ES F ' ( H +( / /S 4 Y Z \ = PP                                             LQFKHV           ș R R 1RWHV 3ODVWLFRUPHWDOSURWUXVLRQVRIPPLQFKPD[LPXPSHUVLGHDUHQRWLQFOXGHG 3ODVWLFRUPHWDOSURWUXVLRQVRIPPLQFKPD[LPXPSHUVLGHDUHQRWLQFOXGHG Fig 8. 5()(5(1&(6 287/,1( 9(56,21 ,(& -('(& 627 ( 06 -(,7$ (8523($1 352-(&7,21 ,668('$7(   Package outline SOT96-1 (SO8) TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 14 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 15. Handling information All input and output pins are protected against ElectroStatic Discharge (ESD) under normal handling. When handling ensure that the appropriate precautions are taken as described in JESD625-A or equivalent standards. 16. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 16.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 16.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 16.3 Wave soldering Key characteristics in wave soldering are: TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 15 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities 16.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 9) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 9 and 10 Table 9. SnPb eutectic process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350  350 < 2.5 235 220  2.5 220 220 Table 10. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 9. TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 16 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 9. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 17 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 17. Appendix: ISO 11898-2:2016 parameter cross-reference list Table 11. ISO 11898-2:2016 to NXP data sheet parameter conversion ISO 11898-2:2016 NXP data sheet Parameter Notation Symbol Parameter Single ended voltage on CAN_H VCAN_H VO(dom) dominant output voltage Single ended voltage on CAN_L VCAN_L Differential voltage on normal bus load VDiff VO(dif) differential output voltage VSYM VTXsym transmitter voltage symmetry Absolute current on CAN_H ICAN_H IO(sc)dom Absolute current on CAN_L ICAN_L dominant short-circuit output current HS-PMA dominant output characteristics Differential voltage on effective resistance during arbitration Optional: Differential voltage on extended bus load range HS-PMA driver symmetry Driver symmetry Maximum HS-PMA driver output current HS-PMA recessive output characteristics, bus biasing active/inactive VO(rec) recessive output voltage VDiff VO(dif) differential output voltage tdom tto(dom)TXD TXD dominant time-out time Single ended output voltage on CAN_H VCAN_H Single ended output voltage on CAN_L VCAN_L Differential output voltage Optional HS-PMA transmit dominant timeout Transmit dominant timeout, long Transmit dominant timeout, short HS-PMA static receiver input characteristics, bus biasing active/inactive Recessive state differential input voltage range VDiff Vth(RX)dif differential receiver threshold voltage Vrec(RX) receiver recessive voltage Vdom(RX) receiver dominant voltage Dominant state differential input voltage range HS-PMA receiver input resistance (matching) Differential internal resistance RDiff Ri(dif) differential input resistance Single ended internal resistance RCAN_H RCAN_L Ri input resistance Matching of internal resistance MR Ri input resistance deviation tLoop td(TXDH-RXDH) delay time from TXD HIGH to RXD HIGH td(TXDL-RXDL) delay time from TXD LOW to RXD LOW HS-PMA implementation loop delay requirement Loop delay Optional HS-PMA implementation data signal timing requirements for use with bit rates above 1 Mbit/s up to 2 Mbit/s and above 2 Mbit/s up to 5 Mbit/s tBit(Bus) tbit(bus) transmitted recessive bit width Received recessive bit width @ 2 Mbit/s / @ 5 Mbit/s tBit(RXD) tbit(RXD) bit time on pin RXD Receiver timing symmetry @ 2 Mbit/s / @ 5 Mbit/s tRec trec receiver timing symmetry Transmitted recessive bit width @ 2 Mbit/s / @ 5 Mbit/s, intended TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 18 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver Table 11. ISO 11898-2:2016 to NXP data sheet parameter conversion …continued ISO 11898-2:2016 NXP data sheet Parameter Notation Symbol Parameter VDiff V(CANH-CANL) voltage between pin CANH and pin CANL Vx voltage on pin x HS-PMA maximum ratings of VCAN_H, VCAN_L and VDiff Maximum rating VDiff General maximum rating VCAN_H and VCAN_L VCAN_H Optional: Extended maximum rating VCAN_H and VCAN_L VCAN_L HS-PMA maximum leakage currents on CAN_H and CAN_L, unpowered Leakage current on CAN_H, CAN_L ICAN_H ICAN_L IL leakage current tFilter twake(busdom)[1] bus dominant wake-up time HS-PMA bus biasing control timings CAN activity filter time, long twake(busrec)[1] bus recessive wake-up time tWake tto(wake)bus bus wake-up time-out time Timeout for bus inactivity tSilence tto(silence) bus silence time-out time Bus Bias reaction time tBias td(busact-bias) delay time from bus active to bias CAN activity filter time, short Wake-up timeout, short Wake-up timeout, long [1] tfltr(wake)bus - bus wake-up filter time, in devices with basic wake-up functionality TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 19 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 18. Revision history Table 12. Revision history Document ID Release date Data sheet status Change notice Supersedes TJF1051 v.5.1 20160713 Product data sheet - TJF1051 v.4 Modifications: • Table 5 – Table note 1: added for parameter Vx – new parameter added: (V(CANH-CANL)) – text in Conditions column of parameter Vx corrected – parameter Vtrt reformatted • • • Section 7.2.1: Last sentence: bit rate changed from 40 kbit/s to 20 kbit/s Section 12.1: Figure 5 modified ISO 11898-2:2016 compliance – Section 1: text revised (3rd paragraph) – Section 2.1: second list item revised – Table 7: New table note added for the non-VIO product variant TJF1051T (Table note 3) – Table 7: Parameter for VO(dom) modified – Table 7: Parameter VTXsym added – Table 7: Parameter VO(dif)bus changed to VO(dif); Conditions revised – Table 7: Parameter Vth(RX)dif: Conditions revised; previous Table note 3 deleted – Table 7: Parameter Vrec(RX) added – Table 7: Parameter Vdom(RX) added – Table 7: Parameter Vhys(RX)dif: Conditions revised – Table 7: Parameter IO(sc)dom: Conditions revised – Table 7: Parameter IL: Conditions revised – Table 7: previous note 3 deleted – Section 11: Figure 3 and Figure 4 replaced – Table 8: parameters tbit(bus) and trec added – Table 8: parameter tPD(RXD-RXD) replaced by td(TXDL-RXDL) and td(TXDH-RXDH) – Table 8: additional condition and specification values added to parameter tbit(RXD) – Section 13: Figure 7 added – Section 17 “Appendix: ISO 11898-2:2016 parameter cross-reference list” added TJF1051 v.4 20150115 Product data sheet - TJF1051 v.3 TJF1051 v.3 20130208 Product data sheet - TJF1051 v.2 TJF1051 v.2 20110512 Product data sheet - TJF1051 v.1 TJF1051 v.1 20100810 Product data sheet - - TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 20 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 19. Legal information 20. Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 20.1 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 20.2 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. TJF1051 Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 21 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. 20.3 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 21. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com TJF1051 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 — 13 July 2016 © NXP N.V. 2016. All rights reserved. 22 of 23 TJF1051 NXP Semiconductors High-speed CAN transceiver 22. Contents 1 2 2.1 2.2 2.3 3 4 5 6 6.1 6.2 7 7.1 7.1.1 7.1.2 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.3 8 9 10 11 12 12.1 12.2 13 14 15 16 16.1 16.2 16.3 16.4 17 18 19 20 20.1 20.2 20.3 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Low-power management . . . . . . . . . . . . . . . . . 1 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Operating modes . . . . . . . . . . . . . . . . . . . . . . . 5 Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Silent mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Fail-safe features . . . . . . . . . . . . . . . . . . . . . . . 5 TXD dominant time-out function . . . . . . . . . . . . 5 Internal biasing of TXD and S input pins . . . . . 6 Undervoltage detection on pins VCC and VIO . . 6 Overtemperature protection . . . . . . . . . . . . . . . 6 VIO supply pin (TJF1051T/3) . . . . . . . . . . . . . . 6 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Thermal characteristics . . . . . . . . . . . . . . . . . . 7 Static characteristics. . . . . . . . . . . . . . . . . . . . . 7 Dynamic characteristics . . . . . . . . . . . . . . . . . 10 Application information. . . . . . . . . . . . . . . . . . 12 Application diagram . . . . . . . . . . . . . . . . . . . . 12 Application hints . . . . . . . . . . . . . . . . . . . . . . . 12 Test information . . . . . . . . . . . . . . . . . . . . . . . . 13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 14 Handling information. . . . . . . . . . . . . . . . . . . . 15 Soldering of SMD packages . . . . . . . . . . . . . . 15 Introduction to soldering . . . . . . . . . . . . . . . . . 15 Wave and reflow soldering . . . . . . . . . . . . . . . 15 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 15 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 16 Appendix: ISO 11898-2:2016 parameter cross-reference list . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 20 Legal information. . . . . . . . . . . . . . . . . . . . . . . 21 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 21 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 22 21 22 Contact information . . . . . . . . . . . . . . . . . . . . 22 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP N.V. 2016. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 13 July 2016 Document identifier: TJF1051