825F15K

89 Series The 89 Series are high-performance axial-lead type resistors. These molded-construction metal-housed resistors are available in higher power ratings than standard axial-lead resistors and are better suited to withstanding vibration, shock and harsh environmental conditions. The 89 Series Metal-Mite® resistors are aluminum housed to maintain high stability during operation and to permit secure mounting to chassis surfaces. The metal housing also provides heat-sinking capabilities, allowing the units to exceed the power ratings set by MIL specifications. Use the 89 Series resistors with the confidence that they meet or exceed MIL-R-18546 specifications. Metal-Mite® MIL-R-18546 Approved Aluminum Housed Axial Lead Wirewound Resistors 1% Tolerance R C N lead hole dia. G F B J E M S H A Series Wattage Ohms 805 (RE60G) 5 0.10-25K 810 (RE65G) 10 0.10-50K 825 (RE70G) 25 0.005-75K 850 (RE75G) 50 0.005-100K Dimensions (in. / mm) Length Height Width 1.125 / 28.58 0.320 / 8.13 0.646 / 16.41 1.375 / 34.93 0.390 / 9.91 0.800 / 20.32 1.938 / 49.23 0.546 / 13.87 1.080 / 27.43 2.781 / 70.64 0.610 / 15.49 1.140 / 28.96 Voltage 210 320 520 1170 Non-Inductive versions available. Insert “N” before tolerance code. Example: 850NF560 Dim. (in. ±.010/mm ±.254) Dim. A Dim. B Dim. C Dim. E Dim. F Dim. G Dim. H Dim. J Dim. M Dim. N Dim. R S min AWG Diam. S (mm) 5 watt 0.444/11.28 11.28 0.490/12.45 12.45 0.600/15.24 15.24 0.334/ 8.48 0.646/16.41 0.320/ 8.13 0.060/ 1.52 0.156/ 3.90 0.085/ 2.16 0.050/ 1.27 1.125/28.58 28.58 16 1.29 10 watt 0.562/14.27 14.27 0.625/15.88 0.750/19.05 0.420/10.67 10.67 0.800/20.32 0.390/ 9.91 0.075/ 1.90 0.183/ 4.65 0.140/ 3.56 0.086/ 2.18 1.375/34.93 12 2.05 25 watt 0.719/18.26 0.781/19.84 1.062/26.97 26.97 0.550/13.97 13.97 1.080/27.43 0.546/13.87 13.87 0.088/ 2.24 0.231/ 2.54 0.140/ 3.56 0.086/ 2.18 1.938/49.23 12 2.05 50 watt 1.563/39.70 0.844/21.44 1.968/49.99 0.630/16.00 1.140/28.96 0.610/15.49 0.088/ 2.24 0.260/ 2.54 0.140/ 3.56 0.086/ 2.18 2.781/70.64 12 2.05 FEATURES • High Stability: ±0.5% ∆R. • High power to size ratio. • Metal housing allows chassis mounting and provides heat sink capability. SPECIFICATIONS Material Housing: Metal, anodized aluminum. Internal Coating: Silicone. Core: Ceramic. Terminals: Solder-coated axial lead. Derating: Linearly from 100% @ +25°C to 0% @ +275°C. Electrical Tolerance: ±1% and ±5% (other tolerances available). Power rating: Rating is based on chassis mounting area and temperature stability. Proper heat sink as follows: 5W and 10W units, 4” x 6” x 2” x .040” Aluminum chassis; 25W units, 5” x 7” x 2” x .040” Aluminum chassis; 50W units, 12” x 12” x .059” Aluminum panel. Maximum ohmic values: See chart. Overload: 5 times rated wattage for 5 seconds. Temperature coefficient: Under 1Ω: ±90 ppm/°C 1 to 9.99Ω: ±50 ppm/°C 10Ω and over: ±20 ppm/°C. Dielectric withstanding voltage: 5W and 10W rating,1000 VAC; 25 and 50W ratings, 2250 VAC. S T O C K PA RT N U M B E R S F O R S TA N D A R D R E S I S TA N C E VA L U E S                                                        1,500 2,000 2,500 3,000 3,500 4,000 4,500 5,000 6,000 10,000 15,000 20,000 25,000 50,000 75,000 100,000                            850F––– 50 825F––– 25 Part No. Prefix  Suffix –––1K5 –––2K0 –––2K5 –––3K0 –––3K5 –––4K0 –––4K5 –––5K0 –––6K0 –––10K –––15K –––20K –––25K –––50K –––75K –––100K 805F––– 5 810F––– 10 Ohmic value 850F––– 50 20 25 30 40 50 75 100 150 200 250 300 400 500 750 1,000 825F––– 25         805F––– 5 810F––– 10 Ohmic value 825F––– 25 850F––– 50 805F––– 5 810F––– 10                              Part No. Prefix  Suffix –––20R –––25R –––30R –––40R –––50R –––75R –––100 –––150 –––200 –––250 –––300 –––400 –––500 –––750 –––1K0 Wattage  24  Part No. Prefix  Suffix 0.005–––R005 0.010–––R010 0.025–––R025 0.1 –––R10 0.3 –––R30 0.5 –––R50 0.7 –––R70 1.0 –––1R0 1.5 –––1R5 2.0 –––2R0 3.0 –––3R0 4.0 –––4R0 5.0 –––5R0 10.0 –––10R 15.0 –––15R Wattage  Ohmic value Wattage          = Most popular stock values  = Stock values  = Non-stock values subject to minimum handling charge per item Shaded values involve very fine resistance wire and should not be used in critical applications without burn-in and/or thermal cycling.         Ohmite Mfg. Co. 1600 Golf Rd., Suite 850, Rolling Meadows, IL 60008 • Tel. 1-866-9-OHMITE • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com