AG-030

AG Series Single Phase EMI Filters These series range of General Purpose filters are designed to suppress undesirable electrical disturbances in Power Lines. They limit the amplitude of interfering voltages on AC power lines and prevent them from propagating into or out of the filtered equipment. F e at u r e s • Rated Current up to 100A • Medical Version available • High Conducted attenuation performance • Chassis mounting a p p l i c at i o n s • Power Systems • Electronic Equipment • Frequency convertors • Stepper motor drives • UPS/Inverters S e r i e s S p e c i f i c at i o n s Part No. AG-001 AG-002 AG-003 AG-006 AG-010 AG-015 AG-016 AG-020 AG-025 AG-030 AG-035 AG-040 AG-050 AG-060 AG-075 AG-080 AG-100 Rated Leakage current current (mA) Termination @40°C @250VAC/50Hz Tab Screw 1A 0.34 6.3 x 0.8 2A 0.34 6.3 x 0.8 3A 0.34 6.3 x 0.8 6A 0.34 6.3 x 0.8 10A 0.34 6.3 x 0.8 15A 0.34 6.3 x 0.8 16A 0.34 6.3 x 0.8 20A 0.34 6.3 x 0.8 25A 0.73 M5 30A 0.73 M5 35A 0.73 M5 40A 0.73 M5 50A 0.73 M6 60A* 0.73 M6 75A* 0.73 M8 80A* 0.73 M8 100A* 0.73 M10 Weight (kg) 0.06 0.06 0.06 0.06 0.06 0.125 0.125 0.260 0.6 0.6 0.6 0.6 1 1 2 2 2 *Not covered under CSA characteristics Max. Cont. Oper. Voltage 250VAC Operating Frequency 50/60Hz Current ratings 1A to 100A @40°C High Potential test voltage L to G 2120Vdc for 1 Minute; L to L 1414Vdc for 1 Minute Design Corresponding to UL 60939-3, CSA 22.2 No.8-13 and IEC 60939 Overload Capability 135% of Rated current for 15 minutes Flammability corresponding to UL 94 V-0 Temperature range -25°C to +85ºC Climatic Category 25/85/21 Recommended Torque (Nm) M5: 1.0-2.0; M6: 1.25 – 2.5; M8: 2.5-5; M10: 3.5-7 (continued) 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com 1 AG Series Single Phase EMI Filters c i r c u i t d i ag r a m L L L I E N E L' Cy Cx R E Cy L O A D N' N i n s e r t i o n l o ss -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 1A 2A 3A 6A -70 -80 10A 15/16A 20A 25A -70 -80 -90 -90 Start 30.00kHz Stop 30.00MHz Start 30.00kHz -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 30A 35A 40A 50A -70 -80 Stop 30.00MHz 60A 75A 80A 100A -70 -80 -90 -90 Start 30.00kHz Stop 30.00MHz Start 30.00kHz Stop 30.00MHz (continued) 2 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com AG Series Single Phase EMI Filters dimensions All dimensions in mm; Tolerances according to ISO2768-m 1A-10A 25A to 40A Ø5 55 ±.2 44.5 ±.3 9.35 78.5 65 ±.5 86 ±.5 21 ±.3 32 ±.3 107 96.5 ±.3 6.3x0.8 40 ±1 46.5 7 15A & 16A Ø5x6.2 100 ±.5 60.5 ±.2 51 ±.3 27.5 ±.3 45 ±.3 73.5 ±.5 50A to 60A 6.3x0.8 80 100 ±.5 115 ±.25 20A 130 4 75 ±.2 8 Ø5 50 ±.5 51 ±1 39 ±1 62 6.3x0.8 120 ±.5 75A to 100A 120 85 ±.5 ORDERIN G IN F ORM A TION AG-002 Series Current rating 135 ±.25 120 150 Standard part numbers AG-001 AG-002 AG-003 AG-006 AG-010 AG-015 AG-016 AG-020 AG-025 AG-030 AG-035 AG-040 AG-050 AG-060 AG-075 AG-080 AG-100 4 8 180 ±.5 rev 05/20-1 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com 3 70 ±.5