AH-20

AH Series Single-phase Dual-stage EMI Filters These series range of double stage filters give superior performance when used in applications with low Impedance loads controlling pulsed, continuous and intermittent interference noise and where high levels of mains borne interference are present. F e at u r e s s e r i e s s p e c i f i c at i o n s Standard Part No. AH-01 AH-02 AH-03 AH-06 AH-10 AH-15 AH-20 AH-25 AH-30 AH-35 AH-40 AH-50 • Double stage filter • Medical Version available • Superior Performance • Chassis mounting a p p l i c at i o n s • Power Systems • Electronic Equipment • Frequency convertors • Stepper motor drives • UPS/Inverters Rated Leakage current current (mA) Termination @40°C @250VAC/50Hz Tab Screw 1A 0.34 6.3 x 0.8 2A 0.34 6.3 x 0.8 3A 0.34 6.3 x 0.8 6A 0.34 6.3 x 0.8 10A 0.34 6.3 x 0.8 15A 0.34 6.3 x 0.8 20A 0.73 M5 25A 0.73 M5 30A 0.73 M5 35A 0.73 M5 40A 0.73 M5 50A 0.73 M6 Weight (kg) 0.125 0.125 0.17 0.17 0.17 0.26 0.65 0.65 0.65 1 1 2 c ha r a c t e r i s t i c s i n s e r t i o n l o ss Max. Cont. Oper. Voltage 250VAC Operating Frequency 50/60Hz -10 Current ratings 1A to 50A @40°C -20 High Potential test voltage L to G 2120Vdc for 1 Minute; L to L 1414Vdc for 1 Minute -30 -40 Design corresponding to UL 60939-3, CSA 22.2 No.8-13 and IEC 60939 -50 -60 -70 -80 -90 1A 2A 3A 6A 10A 15A Overload Capability 135% of Rated current for 15 minutes Flammability corresponding to UL 94 V-0 Temperature range -25°C to +85ºC Start 30.00kHz Stop 30.00MHz Climatic Category 25/85/21 Recommended Torque (Nm) M5: 1.0-2.0; M6: 1.25 – 2.5; M8: 2.5-5; M10: 3.5-7 -10 -20 LC1 L -30 L I E N E -40 -50 -60 20A 25A 30A 35A 40A 50A -70 -80 -90 Start 30.00kHz LC2 Cx Cx L' Cy R Cy N' N Stop 30.00MHz 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com L O A D (continued) 1 AH Series Single-phase Dual-stage EMI Filters dimensions All dimensions in mm; Tolerances according to ISO2768-m 80 35A & 40A Ø5x6.2 1A & 2A 60.5 ±.2 51 ±.3 73.5 ±.5 100 ±.5 115 ±.25 27.5 ±.3 45 ±.3 130 6.3x0.8 4 8 3A to 10A 50 ±.5 75 ±.2 Ø5 51 ±1 120 ±.5 64 33.5 ±.5 6.3x0.8 120 50A 85 ±.5 15A 135 ±.25 75 ±.2 120 150 Ø5 51 ±1 4 62 39 ±1 8 6.3x0.8 85 ±.5 20A to 30A 9.35 180 ±.5 78.5 86 ±.5 107 96.5 ±.3 40 ±1 46.5 7 100 ±.5 ORDERIN G IN F ORM A TION AH-02 Series Current rating Standard part numbers AH-01 AH-02 AH-03 AH-06 AH-10 AH-15 AH-20 AH-25 AH-30 AH-35 AH-40 AH-50 rev 05/20-1 2 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com 70 ±.5