AH-L12

AHL Series Low-frequency Single-phase Dual-stage EMI Filters These series range of double stage filters give superior performance when used in applications with low Impedance loads controlling pulsed, continuous and intermittent interference noise and where high levels of mains borne interference are present. Filter with additional differential mode rejection in low frequency. For use with switched mode power supplies to reduce noise from power supply back into the mains. Filter also provides good attenuation of incoming interference i n s e r t i o n l o ss F e at u r e s a p p l i c at i o n s • Double stage filter • Medical Version available • Superior Performance • Chassis mounting • Power Systems • Electronic Equipment • Frequency convertors • Stepper motor drives • UPS/Inverters -10 s e r i e s s p e c i f i c at i o n s -20 -30 -40 -50 -60 1A 2A 3A 6A -70 -80 -90 Start 30.00kHz Stop 30.00MHz -10 -20 -30 -40 -50 -60 10A 15A 20A 25A -70 -80 -90 Part No. AH-L01 AH-L02 AH-L03 AH-L06 AH-L10 AH-L15 AH-L20 AH-L25 AH-L30 AH-L35 AH-L40 AH-L50 Rated Leakage current current (mA) Termination @40°C @250VAC/50Hz Tab Screw 1A 0.34 6.3 x 0.8 2A 0.34 6.3 x 0.8 3A 0.34 6.3 x 0.8 6A 0.34 6.3 x 0.8 10A 0.34 6.3 x 0.8 15A 0.34 6.3 x 0.8 20A 0.73 M5 25A 0.73 M5 30A 0.73 M5 35A 0.73 M5 40A 0.73 M5 50A 0.73 M6 Weight (kg) 0.125 0.125 0.17 0.17 0.17 0.26 0.65 0.65 0.65 1 1 2 c ha r a c t e r i s t i c s Max. Cont. Oper. Voltage 250VAC Operating Frequency 50/60Hz Start 30.00kHz Stop 30.00MHz Current ratings 1A to 50A @40°C High Potential test voltage L to G 2120Vdc for 1 Minute; L to L 1414Vdc for 1 Minute -10 Design corresponding to UL 60939-3, CSA 22.2 No.8-13 and IEC 60939 -20 -30 Overload Capability 135% of Rated current for 15 minutes -40 Flammability corresponding to UL 94 V-0 -50 Temperature range -25°C to +85ºC -60 Climatic Category 25/85/21 30A 40A 50A -70 -80 Recommended Torque (Nm) M5: 1.0-2.0; M6: 1.25 – 2.5; M8: 2.5-5; M10: 3.5-7 -90 Start 30.00kHz (continued) Stop 30.00MHz 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com 1 AHL Series Low-frequency Single-phase Dual-stage EMI Filters Circuit Diagram LD LC L L I E N E Cx L' Cy Cx L O A D R Cy N' N dimensions All dimensions in mm; Tolerances according to ISO2768-m 80 35A & 40A Ø5x6.2 1A & 2A 60.5 ±.2 51 ±.3 73.5 ±.5 100 ±.5 115 ±.25 27.5 ±.3 45 ±.3 130 6.3x0.8 4 8 3A to 10A 50 ±.5 75 ±.2 Ø5 51 ±1 120 ±.5 64 33.5 ±.5 6.3x0.8 50A 120 85 ±.5 15A 135 ±.25 75 ±.2 120 150 Ø5 51 ±1 4 62 39 ±1 8 70 ±.5 6.3x0.8 85 ±.5 20A to 30A 9.35 180 ±.5 78.5 ORDERING IN F ORM A TION 86 ±.5 96.5 ±.3 107 AH-L02 Series 40 ±1 rev 08/20-1 2 46.5 Low Current frequency rating 7 100 ±.5 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com Standard part numbers AH-L01 AH-L02 AH-L03 AH-L06 AH-L10 AH-L15 AH-L20 AH-L25 AH-L30 AH-L35 AH-L40 AH-L50