RW0S6BA1K00FET

2010 SMD 0.6 Watt Wirewound Surface Mount Power Standard pedestal mount FEATURES • 1% Tolerance standard • Smallest wirewound on the market • Available in low ohmic values SPECIFICATIONS 25°C ambient Power: 0.6 watts Voltage (max.): 50V Tolerance: 1% Resistance range: 0.010Ω–100Ω Temperature Coefficient: 0.1Ω–1Ω: ±90 1Ω–10Ω: ±50 10Ω+: ±20 Dielectric Withstanding Voltage: 1000V Tape Size: 12mm, 13” reel, 2500 pcs. per reel. TCR Recessed-base mount500 400 300 2010 Package 200 100 Typical TCR for less than 0.1Ω SMD resistors (PPM/°C) Flexible J-bend DERATING 100 Percent Rated Power 80 60 40 20 0 0 25 50 75 100 125 Ambient Temperature, °C 150 Dimensions (in. / mm) Series Wattage Ohms Length Height Width Voltage RW0S6BB 0.6 0.01-100 0.202 / 5.14 0.135 / 3.42 0.1 / 2.54 50 0.02 0.04 0.06 0.08 0.10 Ohms P E R F O R M A N C E D ATA Temp. cycle Load Life Immersion Leaching Thermal Shock Flammability 200 180 160 Temperature rise, °C 140 120 100 80 60 40 20 FR4 (-55°C to 125°C, 1000 cycles) (1000 hours at 25°C) (260°C for 10 sec.) (260°C Solder immersion, 60 sec.) (Units at -55°C, then rated power applied) UL Material rating ±0.5%+.05Ω ±3.0%+.05Ω ±0.1%+.05Ω No visible leaching No mechanical damage UL94V0 DIMENSIONS 0.202" ±.010 5.140mm ±.508 0.10" ±.010 2.54mm ±.127 0.135" ±.005 3.420mm ±.127 Package limit hot spot temperature rise 100% Percent Rated power The temperature rise graph data was obtained by a selection of test substrate Alumina size and trace width for each resistor size to limit operating temperatures to safe values. The operating temperature safe rises are either 100°C substrate temperature rise or 180°C package hot spot temperature rise at 25°C ambient. FR4: 0.062 in. thick; 0.062 Solder joint in. traces Alumina: 0.040 in. thick; 0.010 in. traces 200% 300% E Note 2 0.079" ±.010 0.050" Nom. 2.00mm ±.254 1.280mm Nom. 0.005 ± .001 0.065" ±.012 1.640mm ±.305 0.095" Ref. 2.41mm Ref. LAND PATTERN 0.328" / 8.33mm 0.125" 3.20mm 0.078" / 1.98mm 0.026" / 0.66mm Note 2: Test point is .020 above PCB. Note 3: Tape and reel dimensions per EIA 481 A except “EA” size which is 12 mm component pitch versus 16mm pitch. Land pattern dimensions are for reference only O R D E R I N G I N F O R M AT I O N Type of Base S = standard P ackage B = 12mm P ackage Modifier A, B sequential Tolerance F = 1% Component type R = resistor �������������� Component Modifier W = wirewound Wattage 0S6 = 0.6W T = Tape and Reel (optional) 0.126" 3.18mm E = RoHS compliant Resistance Value R = Decimal Examples: K = 1,000 R249 = 0.249 ohms M = 1,000,000 24R9 = 24.9 ohms 2K49 = 2,490 ohms Recommended for glue dot application TAPE AND REEL 0.795* 20.2 min. S TA N D A R D PA RT N U M B E R S F O R 2 0 1 0 S M D Ohms 0.010 0.015 0.020 0.030 0.050 0.075 0.100 0.240 0.470 0.750 Part Number RW0S6BBR010FE RW0S6BBR015FE RW0S6BBR020FE RW0S6BBR030FE RW0S6BBR050FE RW0S6BBR075FE RW0S6BBR100FE RW0S6BBR240FE RW0S6BBR470FE RW0S6BBR750FE Ohms 1.00 2.00 5.00 7.50 10.00 15.00 24.00 36.00 47.00 100.00 Part Number RW0S6BB1R00FE RW0S6BB2R00FE RW0S6BB5R00FE RW0S6BB7R50FE RW0S6BB10R0FE RW0S6BB15R0FE RW0S6BB24R0FE RW0S6BB36R0FE RW0S6BB47R0FE RW0S6BB100RFE 0.724" 18.4mm 0.512 ±.008 13.0 ±.200 1.973 50 min. 0.059* 1.5 min. 13" nom. Full Radius Tape Start Slot 0.488" +0.078/–0.00 12.4mm +2.0/–0.0 measured at hub Check product availability at www.ohmite.com 0.098 / 2.5 min. width 0.394 / 10 min. depth Reels are compatible with major pickand-place machines and made in accordance with EIA 481 A. 12 Ohmite Mfg. Co. 1600 Golf Rd., Rolling Meadows, IL 60008 • 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com 0.006 Ref.