MSM80C86A-10JS

E2O0010-27-X2 ¡ Semiconductor MSM80C86A-10RS/GS/JS ¡ Semiconductor 16-Bit CMOS MICROPROCESSOR This version: Jan. 1998 MSM80C86A-10RS/GS/JS Previous version: Aug. 1996 GENERAL DESCRIPTION The MSM80C86A-10 is complete 16-bit CPUs implemented in Silicon Gate CMOS technology. They are designed with same processing speed as the NMOS 8086-1 but have considerably less power consumption. It is directly compatible with MSM80C88A-10 software and MSM80C85AH hardware and peripherals. FEATURES • 1 Mbyte Direct Addressable Memory Space • Internal 14-word by 16-bit Register Set • 24-Operand Addressing Modes • Bit, Byte, Word and String Operations • 8 and 16-bit Signed and Unsigned Arithmetic Operation • From DC to 10 MHz Clock Rate (Note) • Low Power Dissipation 10 mA/MHz • Bus Hold Circuitry Eliminated Pull-up Resistors • 40-pin Plastic DIP (DIP40-P-600-2.54): (Product name: MSM80C86A-10RS) • 44-pin Plastic QFJ (QFJ44-P-S650-1.27): (Product name: MSM80C86A-10JS) • 56-pin Plastic QFP (QFP56-P-1519-1.00-K): (Product name: MSM80C86A-10GS-K) (Note) 10 MHz Spec is not compatible with Intel 8086-1 Spec. 1/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS CIRCUIT CONFIGURATION Exeuction Unit Register File Data Pointer and Index Registers (8 Words) Bus Interface Unit Relocation Register File Segment Registers and Instruction Pointer (5 Words) 16-Bit ALU 4 Flags Bus Interface Unit BHE/S7 A19/S6 . . . A16/S3 AD15 - AD0 INTA, RD, WR, M/IO DT/R, DEN, ALE 16 4 3 6Byte Instruction Queue TEST INTR NMI RQ/GT0, 1 HOLD HLDA 3 2 LOCK 2 Control & Timing QS0, QS1 S 2 , S 1 , S0 3 CLK RESET READY MN/MX GND VCC 2/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS PIN CONFIGURATION (TOP VIEW) 40 pin Plastic DIP GND AD14 AD13 AD12 AD11 AD10 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 NMI INTR CLK GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 VCC AD15 A16/S3 A17/S4 A18/S5 A19/S6 BHE/S7 MN/MX RD RQ/GT0(HOLD) RQ/GT1(HLDA) LOCK(WR) S2(M/IO) S1(DT/R) S0(DEN) QS0(ALE) QS1(INTA) TEST READY RESET 56 pin Plastic QFP NC AD10 AD9 AD8 AD7 AD6 NC NC AD5 AD4 AD3 AD2 AD1 AD0 56 55 54 53 52 51 50 49 48 47 46 45 44 43 AD11 AD12 AD13 AD14 NC GND NC VCC VCC NC AD15 A16/S3 A17/S4 A18/S5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 42 41 40 39 38 37 36 35 34 33 32 31 30 29 NC A19/S6 BHE/S7 MN/MX RD RQ/GT0(HOLD) NC NC NC RQ/GT1(HLDA) LOCK(WR) S2(M/IO) S1(DT/R) S0(DEN) 15 16 17 18 19 20 21 22 23 24 25 26 27 28 44 pin Plastic QFJ 42 A16/S3 41 A17/S4 44 VCC 40 A18/S5 39 NC 38 A19/S6 37 BHE/S7 36 MN/MX 35 RD 34 RQ/GT0(HOLD) 33 RQ/GT1(HLDA) 32 LOCK(WR) 31 S2(M/IO) 30 S1(DT/R) 29 S0(DEN) 6 AD11 5 AD12 4 AD13 3 AD14 NMI INTR CLK NC NC GND VCC NC NC RESET READY TEST QS1(INTA) QS0(ALE) AD10 7 AD9 8 AD8 9 AD7 10 AD6 11 AD5 12 AD4 13 AD3 14 AD2 15 AD1 16 AD0 17 NC 18 NM1 19 INTR 20 CLK 21 GND 22 NC 23 RESET 24 READY 25 43 AD15 2 GND 1 NC TEST 26 INTA(QS1) 27 ALE(QS0) 28 3/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS ABSOLUTE MAXIMUM RATINGS Rating MSM80C86A-10RS MSM80C86A-10GS MSM80C86A-10JS Parameter Power Supply Voltage Input Voltage Output Voltage Storage Temperature Power Dissipation Symbol Conditions VCC VIN VOUT TSTG PD With respect to GND — Ta = 25°C Unit V V V °C W –0.5 to + 7 –0.5 to VCC +0.5 –0.5 to VCC +0.5 –65 to +150 1.0 0.7 OPERATING RANGE Parameter Power Supply Voltage Operating Temperature Symbol VCC Top Range 4.75 to 5.25 0 to +70 Unit V °C RECOMMENDED OPERATING CONDITIONS Parameter Power Supply Voltage Operating Temperature "L" Input Voltage "H" Input Voltage Symbol VCC TOP VIL VIH *1 *2 Min. 4.75 0 –0.5 VCC –0.8 2.0 Typ. 5.0 +25 — — — Max. 5.25 +70 +0.8 VCC +0.5 VCC +0.5 Unit V °C V V V *1 Only CLK *2 Except CLK 4/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS DC CHARACTERISTICS (VCC = 4.5 to 5.5 V, Ta = –40°C to +85°C) Parameter "L" Output Voltage "H" Output Voltage Input Leak Current Output Leak Current Input Leakage Current (Bus Hold Low) Input Leakage Current (Bus Hold High) Bus Hold Low Overdrive Bus Hold High Overdrive Operating Power Supply Current Standby Power Supply Current Input Capacitance Output Capacitance I/O Capacitance Symbol V OL VOH ILI ILO IBHL IBHH IBHLO IBHHO ICC ICCS CIN COUT CI/O Min. — 3.0 VCC –0.4 –1.0 –10 50 –50 — — — Typ. — — — — — — — — — Max. 0.4 — +1.0 +10 400 –400 600 –600 10 500 10 15 20 Unit V V mA mA mA mA mA mA mA/MHz mA pF pF pF Conditions IOL = 2.5 mA IOH = –2.5 mA IOH = –100 mA 0 £ VIN £ VCC VO = VCC or GND VIN = 0.8 V *3 VIN = 3.0 V *4 *5 *6 VIL = GND VIH = VCC VCC = 5.5 V Outputs Unloaded VIN = VCC or GND *7 *7 *7 — — — — — — — — *3 Test condition is to lower VIN to GND and then raise VIN to 0.8 V on pins 2-16, and 35-39. *4 Test condition is to raise VIN to VCC and then lower VIN to 3.0 V on pins 2-16, 26-32, and 3439. *5 An external driver must source at least IBHLO to switch this node from LOW to HIGH. *6 An external driver must sink at least IBHHO to switch this node from HIGH to LOW. *7 Test Conditions: a) Freq = 1 MHz. b) Unmeasured Pins at GND. c) VIN at 5.0 V or GND. 5/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS AC CHARACTERISTICS Minimum Mode System Timing Requirements 5 MHz Spec. 8 MHz Spec. 10 MHz Spec. VCC = 4.5 V to 5.5 V VCC = 4.75 V to 5.25 V VCC = 4.75 V to 5.25 V Unit Symbol Ta = –40 to +85°C Ta = 0 to +70°C Ta = 0 to +70°C Parameter CLK Cycle Period CLK Low Time CLK High Time CLK Rise Time (From 1.0 V to 3.5 V) CLK Fall Time (From 3.5 V to 1.0 V) Data in Setup Time Data in Hold Time RDY Setup Time into MSM 82C84A-2 (See Notes 1, 2) RDY Hold Time into MSM 82C84A-2 (See Notes 1, 2) READY Setup Time into MSM80C86A-2 READY inactive to CLK (See Note 3) HOLD Setup Time INTR, NMI, TEST Setup Time (See Note 2) Input Rise Time (Except CLK) (From 0.8 V to 2.0 V) Input Fall Time (Except CLK) (From 2.0 V to 0.8 V) tCLCL tCLCH tCHCL tCH1CH2 tCL2CL1 tDVCL tCLDX tR1VCL tCLR1X tRYHCH Min. 200 118 69 — — 30 10 35 0 118 30 –8 35 30 — — Max. DC — — 10 10 — — — — — — — — — 15 15 Min. 125 68 44 — — 20 10 35 0 68 20 –8 20 15 — — Max. DC — — 10 10 — — — — — — — — — 15 15 Min. 100 46 44 — — 20 10 35 0 46 20 –8 20 15 — — Max. DC — — 10 10 — — — — — — — — — 15 15 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns READY Hold Time into MSM80C86A-10 tCHRYX tRYLCL tHVCH tINVCH tILIH tIHIL 6/37 ¡ Semiconductor Timing Responses MSM80C86A-10RS/GS/JS Parameter 5 MHz Spec. 8 MHz Spec. 10 MHz Spec. VCC = 4.5 V to 5.5 V VCC = 4.75 V to 5.25 V VCC = 4.75 V to 5.25 V Unit Symbol Ta = -40 to +85°C Ta = 0 to +70°C Ta = 0 to +70°C Address Valid Delay Address Hold Time Address Float Delay ALE Width ALE Active Delay ALE Inactive Delay Address Hold Time to ALE Inactive Data Valid Delay Data Hold Time Data Hold Time after WR Control Active Delay 1 Control Active Delay 2 Control Inactive Delay Address Float to RD Active RD Active Delay RD Inactive Delay RD Inactive to Next Address Active HLDA Valid Delay RD Width WR Width Address Valid to ALE Low Ouput Rise Time (From 0.8 V to 2.0 V) Output Fall Time (From 2.0 V to 0.8 V) tCLAV tCLAX tCLAZ tLHLL tCLLH tCHLL tLLAX tCLDV tCHDX tWHDX tCVCTV tCHCTV tCVCTX tAZRL tCLRL tCLRH tRHAV tCLHAV tRLRH tWLWH tAVAL tOLOH tOHOL Min. 10 10 tCLAX tCLCH-20 — — tCLCH-10 10 10 tCLCH-30 10 10 10 0 10 10 tCLC-45 10 2tCLCL-75 2tCLCL-60 tCLCH-60 — — Max. 110 — 80 — 80 85 — 110 — — 110 110 110 — 165 150 — 160 — — — 15 15 Min. 10 10 tCLAX tCLCH-10 — — tCLCH-10 10 10 tCLCH-30 10 10 10 0 10 10 tCLCH-40 10 2tCLCL-50 2tCLCL-40 tCLCH-40 — — Max. 60 — 50 — 50 55 — 60 — — 70 60 70 — 100 80 — 100 — — — 15 15 Min. 10 10 tCLAX tCLCH-10 — — tCLCH-10 10 10 tCLCH-25 10 10 10 0 10 10 tCLCL-35 10 2tCLCL-40 2tCLCL-35 tCLCH-35 — — Max. 60 — 50 — 40 45 — 60 — — 55 50 55 — 70 60 — 60 — — — 15 15 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Notes: 1. Signal at MSM82C84A-2 or MSM82C88-2 are shown for reference only. 2. Setup requirement for asynchronous signal only to guarantee recognition at next CLK. 3. Applies only to T2 state. (8 ns into T3) 7/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS Maximum Mode System (Using MSM82C88-2 Bus Controller) Timing Requirements 5 MHz Spec. 8 MHz Spec. 10 MHz Spec. VCC = 4.5 V to 5.5 V VCC = 4.75 V to 5.25 V VCC = 4.75 V to 5.25 V Unit Symbol Ta = –40 to +85°C Ta = 0 to +70°C Ta = 0 to +70°C Parameter CLK Cycle Period CLK Low Time CLK High Time CLK Rise Time (From 1.0 V to 3.5 V) CLK Fall Time (From 3.5 V to 1.0 V) Data in Setup Time Data in Hold Time RDY Setup Time into MSM 82C84A-2 (See Notes 1, 2) RDY Hold Time into MSM 82C84A-2 (See Notes 1, 2) READY Setup Time into MSM80C86A-10 READY inactive to CLK (See Note 3) Setup Time for Recognition (NMI, INTR, TEST) (See Note 2) RQ/GT Setup Time RQ Hold Time into MSM80C86A-10 Input Rise Time (Except CLK) (From 0.8 V to 2.0 V) Input Fall Time (Except CLK) (From 2.0 V to 0.8 V) tCLCL tCLCH tCHCL tCH1CH2 tCL2CL1 tDVCL tCLDX tR1VCL tCLR1X tRYHCH Min. 200 118 69 — — 30 10 35 0 118 30 –8 30 30 40 — — Max. DC — — 10 10 — — — — — — — — — — 15 15 Min. 125 68 44 — — 20 10 35 0 68 20 –8 15 15 30 — — Max. DC — — 10 10 — — — — — — — — — — 15 15 Min. 100 46 44 — — 20 10 35 0 46 20 –8 15 15 20 — — Max. DC — — 10 10 — — — — — — — — — — 15 15 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns READY Hold Time into MSM80C86A-10 tCHRYX tRYLCL tINVCH tGVCH tCHGX tILIH tIHIL 8/37 ¡ Semiconductor Timing Responses MSM80C86A-10RS/GS/JS Timing Response Parameter Command Active Delay (See Note 1) Command Inactive Delay (See Note 1) READY Active to Status Passive (See Note 4) Status Active Delay Status Inactive Delay Address Valid Delay Address Hold Time Address Float Delay Status Valid to ALE High (See Note 1) Status Valid to MCE High (See Note 1) CLK Low to ALE Valid (See Note 1) CLK Low to MCE High (See Note 1) ALE Inactive Delay (See Note 1) Data Valid Delay Data Hold Time Control Active Delay (See Note 1) Control Inactive Delay (See Note 1) Address Float to RD Active RD Active Delay RD Inactive Delay RD Inactive to Next Address Active Direction Control Active Delay (See Note 1) Direction Control Inactive Delay (See Note 1) GT Active Delay (See Note 5) GT Inactive Delay RD Width Output Rise Time (From 0.8 V to 2.0 V) Output Fall Time (From 2.0 V to 0.8 V) 5 MHz Spec. 8 MHz Spec. 10 MHz Spec. VCC = 4.5 V to 5.5 V VCC = 4.75 V to 5.25 V VCC = 4.75 V to 5.25 V Unit Symbol Ta = –40 to +85°C Ta = 0 to +70°C Ta = 0 to +70°C tCLML tCLMH tRYHSH tCHSV tCLSH tCLAV tCLAX tCLAZ tSVLH tSVMCH tCLLH tCLMCH tCHLL tCLDV tCHDX tCVNV tCVNX tAZRL tCLRL tCLRH tRHAV tCHDTL tCHDTH tCLGL tCLGH tRLRH tOLOH tOHOL Min. 5 5 — 10 10 10 10 tCLAX — — — — 4 10 10 5 5 0 10 10 tCLCL-45 — — 0 0 2tCLCL-75 — — Max. 45 45 110 110 130 110 — 80 35 35 35 35 35 110 — 45 45 — 165 150 — 50 35 85 85 — 15 15 Min. 5 5 — 10 10 10 10 tCLAX — — — — 4 10 10 5 5 0 10 10 tCLCL-40 — — 0 0 2tCLCL-50 — — Max. 35 45 65 60 70 60 — 50 25 30 25 25 25 60 — 45 45 — 100 80 — 50 30 50 50 — 15 15 Min. 5 5 — 10 10 10 10 tCLAX — — — — 4 10 10 5 5 0 10 10 tCLCL-35 — — 0 0 2tCLCL-40 — — Max. 35 45 45 45 60 60 — 50 25 30 25 25 25 60 — 45 45 — 70 60 — 50 30 45 45 — 15 15 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Notes: 1. Signals at MSM82C84A-2 or MSM82C88-2 are shown for reference only. 2. Setup requirement for asynchronous signal only to guarantee recognition at next CLK 3. Applies only to T2 state (8 ns into T3) 4. Applies only to T3 and wait states. 5. CL = 40 pF (RQ/GT0, RQ/GT1) 9/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS TIMING DIAGRAM Input/Output 2.4 1.5 0.45 AC, Testing: Inputs are driven at 2.4 V for a logic "1" and 0.45 V for a logic "0". Timing measurements are 1.5 V for both a logic "1" and "0". A.C. Testing Load Circuit Test Points Device Under Test 1.5 CL = 100 pF CL includes jig capacitance. Minimum Mode T1 tCLCL VIH CLK (MSM82C84A-2 Output) VIL M/IO tCLAV BHE/S7, A19/S6 - A16/S3 tCLLH ALE RDY (MSM82C84A-2 Input) See NOTE 5 tCHCTV tCLAX T2 tCH1CH2 T3 Tw tCLCH tCLDV tCHDX T4 tCL2CL1 tCHCL tAVAL tCHLL READY (MSM80C86A-10 Input) Read Cycle AD15 - AD0 RD (NOTE 1) (WR, INTA = VOH) DT/R DEN tCLAV tCHCTV    BHE, A19 - A16 tLHLL S7 - S3 tLLAX VIH VIL tR1VCL tRYLCL tCLR1X tCHRYX tAVAL tLLAX tRYHCH tCLAZ tCLAX tDVCL tCLDX AD15 - AD0 tAZRL Float Data In tCLRH Float tRHAV tCLRL tRLRH tCHCTV tCVCTV tCVCTX 10/37 ¡ Semiconductor Minimum Mode (continued) T1 tCLCL VIH CLK (MSM82C84A-2 Output) V IL M/IO tCLAV BHE/S7, A19/S6 - A16/S3 tCLLH ALE tCHLL Write Cycle AD15 - AD0 (NOTE 1) (RD, INTA DT/R = VOH) DEN WR tCLAZ INTA Cycle AD15 - AD0 tCHCTV (NOTES 1&3) (RD, WR = VOH BHE = VOL) DT/R tCVCTV INTA tCVCTV DEN Software Halt RD, WR, INTA = VOH DT/R = Indeterminate Float tCLAV tCVCTV AD15 - AD0 tAVAL tLLAX BHE, A19 - A16 tLHLL tAVAL tCLDV tCLAX tCLDV tCLAX MSM80C86A-10RS/GS/JS T2 tCH1CH2 T3 tCL2CL1 TW T4 tCHCTV tCHCL tCHDX S7 - S 3 tLLAX tCLCH tCHDX Data Out tWIDX tCVCTX tCVCTV tWLWH tCVCTX tDVCL Pointer tCLDX Float tCHCTV tCVCTX AD15 - AD0 tCLAV Invalid Address Software Halt 11/37 ¡ Semiconductor Maximum Mode T1 tCH1CH2 tCLCL VIH CLK (MSM82C84A-2 Output) VIL QS0, QS1 S2, S1, S0 (Except Halt) BHE/S7, A19/S6 - A16/S3 See NOTE 5 ALE (MSM82C88-2 Output) RDY (MSM82C84A-2 Input) tSVLH tCLLH T2 MSM80C86A-10RS/GS/JS tCLAV tCHSV READY (MSM80C86A-10 Input) Read Cycle AD15 - AD0 RD DT/R MSM82C88-2 Outputs (See NOTES 5, 6) MRDC or IORC DEN tCLAV tCHDTL  
,,
    tCHCL tCLCH T3 tCL2CL1 Tw T4 tCLSH (See NOTE 8) tCLAV tCLDV tCLAX tCHDX BHE A19 - A16 tCHLL VIH VIL S7 - S3 tR1VCL tRYLCL tCLR1X tRYHSH tCHRYX tCLAX tCLAZ tRYHCH AD15 - AD0 tAZRL Float tDVCL Data In tCLRH tCLDX Float tRHAV tCLRL tRLRH tCHDTH tCLML tCLMH tCVNV tCVNX 12/37 ¡ Semiconductor Maximum Mode (continued) T1 CLK (MSM82C84A-2 Output) VIH VIL tCLAV AD15 - AD0 tCVNV DEN MSM82C88-2 Outputs See NOTES 5, 6 AMWC or AIOWC MWTC or IOWC INTA Cycle Float MSM80C86A-10RS/GS/JS T2 S2, S1, S0 (Except Halt) Write Cycle tCHSV tCLAX tCLDV tCLML AD15 - AD0 See NOTE 3, 4 tSVMCH MCE/ PDEN t CLMCH MSM82C88-2 Outputs See NOTES 5, 6 DT/R Float tCLAZ tCVNX Float tCHDTL tCLML   T3 Tw T4 tCLSH (See NOTE 8) tCHDX tCVNX Data tCLMH tCLML tCLMH tDVCL tCLDX Float Pointer tCHDTH INTA tCVNV DEN Software Halt (DEN = VOL; RD, MRDC, IORC, MWTC, AMWC, IOWC, AIOWC, INTA = VOH) AD15 - AD0 tCLAV S2, S1, S0 Invalid Address tCVNX tCLMH Notes: 1. All signals switch between VOH and VOL unless otherwise specified. 2. RDY is sampled near the end of T2, T3, TW to determine if TW machines states are to be inserted. 3. Cascade address is valid between first and second INTA cycle. 4. Two INTA cycles run back-to-back. The MSM80C86A-10 LOCAL ADDR/ DATA BUS is floating during both INTA cycles. Control for pointer address is shown for second INTA cycle. 5. Signals at MSM82C84A-2 or MSM82C88-2 are shown for reference only. 6. The issuance of the MSM 82C88-2 command and control signals (MRDC, MWTC, AMWC, IORC, IOWC, AIOWC, INTA and DEN) lags the active high MSM82C88-2 CEN. 7. All timing measurements are made at 1.5 V unless otherwise noted. 8. Status inactive in state just prior to T4 13/37 ¡ Semiconductor Asynchronous Signal Recognition CLK NMI INTR Signal TEST tINVCH (See NOTE 1) MSM80C86A-10RS/GS/JS NOTE: 1 Setup requirements for asynchronous signals only to guarantee recognition at next CLK Bus Lock Signal Timing (Maximum Mode Only) Any CLK Cycle Any CLK Cycle Reset Timing ≥ 50msec VCC CLK Reset ≥ 4 CLK Cycles CLK tCLAV tCLAV tCLDX tDVCL LOCK Request/Grant Sequence Timing (Maximum Mode Only) Any CLK Cycle > 0 CLK Cycle CLK tCLGH RQ/GT AD15 - AD0 A19/S6 - A16/S3 S2, S1, S0, RD, CLOCK BHE/S7 ≥ tCLCL tGVCH tCHGX Pulse 1 Coprocessor RQ MSM80C86A-10 ≥ tCLCL tCLGL Pulse 2 80C86AGT tCLGH Pulse 3 Coprocessor Release tCLAZ Coprocessor (See NOTE 1) MSM80C86A-10 NOTE: 1 The coprocessor may not drive the buses outside the region shown without risking contention. Hold/Hold Acknowledge Timing (Minimum Mode Only) ≥ 1 CLK Cycle 1 or 2 Cycles CLK tHVCH HOLD tCLHAV HLDA AD15 - AD0, A19/S6 - A16/S3, RD, BHE/S7, M/IO DT/R, WR, DEN tCLAZ MSM80C86A-10 Coprocessor MSM80C86A-10 tHVCH tCLHAV 14/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS PIN DESCRIPTION AD0 - AD15 ADDRESS DATA BUS: Input/Output These lines are the multiplexed address and data bus. These are the address bus at the T1 cycle and the data bus at the T2, T3, TW and T4 cycles. At the T1 cycle, AD0 low indicates Data Bus Low (D0-D7) Enable. These lines are high impedance during interrupt acknowledge and hold acknowledge. A16/S3. A17/S4, A18/S5, A19/S6 ADDRESS/STATUS: Output These are the four most significant addresses, at the T1 cycle. Accessing I/O port address, these are low at T1 cycles. These lines are Status lines at T2, T3, TW and T4 cycles. S3 and S4 are encoded as shown. S3 0 1 0 1 S4 0 0 1 1 Characteristics Alternate Data Stack Code or None Data These lines are high impedance during hold acknowledge. BHE/S7 BUS HIGH ENABLE/STATUS: Output This line indicates Data Bus High Enable (BHE) at the T1 cycle. This line is status line at T2, T3, TW and T4 cycles. RD READ: Output This line indicates that CPU is in the memory or I/O read cycle. This line is the read strobe signal when CPU read data from memory or I/O device. This line is active low. This line is high impedance during hold acknowledge. READY READY:Input This line indicates to the CPU that the addressed memory or I/O device is ready to read or write. This line is active high. If the setup and hold time is out of specification, illegal operation will occur. INTR INTERRUPT REQUEST: Input This line is the level triggered interrupt request signal which is sampled during the last clock cycle of instruction and string manipulation. It can be internally masked by software. This signal is active high and internally synchronized. 15/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS INTA INTERRUPT ACKNOWLEDGE: Output This line is a read strobe signal for the interrupt acknowledge cycle. This line is active low. TEST TEST: Input This line is examined by the WAIT instruction. When TEST is high, the CPU enters idle cycle. When TEST is low, the CPU exits the idle cycle. NMI NON MASKABLE INTERRUPT: Input This line causes a type 2 interrupt. NMI is not maskable. This signal is internally synchronized and needs 2-clock cycles of pulse width. RESET RESET:Input This signal causes the CPU to initialize immediately. This signal is active high and must be at least four clock cycles. CLK CLOCK: Input This signal provides the basic timing for the internal circuit. MN/MX MINIMUM/MAXIMUM: Input This signal selects the CPU’s operating mode. When VCC is connected, the CPU operates in Minimum mode. When GND is connected, the CPU operates in Maximum mode. VCC VCC: +5V supplied. GND GROUND The following pin function descriptions are maximum mode only. Other pin functions are already described. SO, S1, S2 STATUS: Output These lines indicate bus status and they are used by the MSM82C88-2 Bus Controller to generate all memory and I/O access control signals. These lines are high impedance during hold acknowledge. These status lines are encoded as shown. 16/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS S2 0 (LOW) 0 0 0 1 (HIGH) 1 1 1 S1 0 0 1 1 0 0 1 1 S0 0 1 0 1 0 1 0 1 Characteristics Interrupt acknowledge Read I/O Port Write I/O Port Halt Code Access Read Memory Write Memory Passive RQ/GT0 RQ/GT1 REQUEST/GRANT:Input/Output These lines are used for Bus Request from other devices and Bus GRANT to other devices. These lines are bidirectional and active low. LOCK LOCK:Output This line is active low. When this line is low, other devices cannot gain control of the bus. This line is high impedance during hold acknowledge. QS0/QS1 QUEUE STATUS: Output These lines are Queue Status, and indicate internal instruction queue status. QS1 0 (LOW) 0 1 (HIGH) 1 QS0 0 1 0 1 Characteristics No operation First Byte of Op Code from Queue Empty the Queue Subsequent Byte from Queue The following pin function descriptions are minimum mode only. Other pin functions are already described. M/IO STATUS: Output This line selects memory address space or I/O address space. When this line is high, the CPU selects memory address space and when it is low, the CPU selects I/O address space. This line is high impedance during hold acknowledge. WR WRITE: Output This line indicates that the CPU is in the memory or I/O write cycle. This line is a write strobe signal when the CPU writes data to memory of I/O device. This line is active low. This line is high impedance during hold acknowledge. 17/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS INTA INTERRUPT ACKNOWLEDGE: Output This line is a read strobe signal for the interrupt acknowledge cycle. This line is active low. ALE ADDRESS LATCH ENABLE: Output This line is used for latching the address into the MSM82C12 address latch. It is a positive pulse and its trailing edge is used to strobe the address. This line is never floated. DT/R DATA TRANSMIT/RECEIVE: Output This line is used to control the output enable of the bus transceiver. When this line is high, the CPU transmits data, and when it is low. the CPU receives data. This line is high impedance during hold acknowledge. DEN DATA ENABLE: Output This line is used to control the output enable of the bus transceiver. This line is active low. This line is high impedance during hold acknowledge. HOLD HOLD REQUEST: Input This line is used for Bus Request from other devices. This line is active high. HLDA HOLD ACKNOWLEDGE: Output This line is used for Bus Grant other devices. This line is active high. 18/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS FUNCTIONAL DESCRIPTION STATIC OPERATION The MSM80C86A-10 circuitry is of static design. Internal registers, counters and latches are static and require no refresh as with dynamic circuit design. This eliminates the minimum operating frequency restriction placed on other microprocessors. The MSM80C86A-10 can operate from DC to the appropriate upper frequency limit. The processor clock may be stopped in either state (high/low) and held there indefinitely. This type of operation is especially useful for system debug or power critical applications. The MSM80C86A-10 can be single stepped using only the CPU clock. This state can be maintained as long as is necessary. Single step clock operation allows simple interface circuitry to provide critical information for bringing up your system. Static design also allows very low frequency operation (down to DC). In a power critical situation, this can provide extremely low power operation since MSM80C86A-10 power dissipation is directly related to operating frequency. As the system frequency is reduced, so is the operating power until, ultimately, at a DC input frequency, MSM80C86A-10 power requirement is the standby current (500mA maximum). General Operation The internal function of the MSM80C86A-10 consists of a Bus Interface Unit (BIU) and an Execution Unit (EU). These units operate mutually but perform as separate processors. BIU performs instruction fetch and queueing, operand fetch, DATA read and write address relocation and basic bus control. Instruction pre-fetch is performed while waiting for decording and execution of instructions. Thus, the CPU’s performance is increased. Up to 6-bytes of instructions stream can be queued. The EU receives pre-fetched instructions from the BIU queue, decodes and executes the instructions, and provides the un-relocated operand address to BIU. Memory Organization The MSM80C86A-10 has a 20-bit address to memory. Each address has an 8-bit data width. Memory is organized 00000H to FFFFFH and is logically divided into four segments: code, data, extra data and stack segment. Each segment contains up to 64 Kbytes and locates on a 16-byte boundary. (Fig. 3a) All memory references are made relative to the segment register which functions in accordance with a select rule. Word operands can be located on even or odd address boundary. The BIU automatically performs the proper number of memory accesses. Memory consists of an even address and an odd address. Byte data of even address is transferred on the AD0-AD7 and byte data of odd address is transfered on the AD8-AD15. The CPU provides two enable signals BHE and A0 to access either an odd address, even address or both: Memory location FFFF0H is the start address after reset, and 00000H through 003FFH are reserved as an interrupt pointer, where there are 256 types of interrupt pointers. Each interrupt type has a 4-byte pointer element consisting of a 16-bit segment address and a 16-bit offset address. 19/37 ¡ Semiconductor Memory Organization FFFFFH 64KB Code Segment XXXXOH Stack Segment MSM80C86A-10RS/GS/JS Reserved Memory Locations FFFFFH Reset Bootstrap Program Jump FFFFOH Interrupt Pointer for Type 255 3FFH 3FCH +Offset Segment Register File CS SS DS ES Data Segment Interrupt Pointer for Type 1 Interrupt Pointer for Type 0 7H 4H 3H 0H Extra Data Segment OOOOH Memory Reference Need Instructions Stack Local Data External (Global Data) Segment Register Used CODE (CS) STACK (CS) DATA (DS) EXTRA (ES) Segment Selection Rule Automatic with all instruction prefetch. All stack pushes and pops. Memory references relative to BP base register except data references. Data references when relative to stack, destination of string operation, or explicitly overridden. Destination of string operations: Explicitly selected using a segment overriden. 20/37 ¡ Semiconductor Minimum and Maximum Modes MSM80C86A-10RS/GS/JS The MSM80C86A-10 has two system modes: minimum and maximum. When using maximum mode, it is easy to organize a multi-CPU system with a MSM82C88-2 Bus Controller which generates the bus control signal. When using minimum mode, it is easy to organize a simple system by generating bus control signal by itself. MN/MX is the mode select pin. Definition of 24-31 pin changes depend on the MN/MX pin. Bus Operation The MSM80C86A-10 has a time multiplexed address and data bus. If a non-multiplexed bus is desired for a system, it is only to add the address latch. A CPU bus cycle consists of at least four clock cycles: T1, T2, T3 and T4. (Fig. 4) The address output occurs during T1 and data transfer occurs during T3 and T4. T2 is used for changing the direction of the bus at the read operation. When the device which is accessed by the CPU is not ready for The data transfer and the CPU “NOT READY”, TW cycles are inserted between T3 and T4. When a bus cycle is not needed, T1 cycles are inserted between the bus cycles for internal execution. During the T1 cycle, the ALE signal is output from the CPU or the MSM82C88-2 depending on MN/MX. At the trailing edge of ALE, a valid address may be latched. Status bits S0, S1 and S2 are used in the maximum mode by the bus controller to recognize the type of bus operation according to the following table. Status bits S3 through S7 are multiplexed with A16 - A19, and BHE: therefore, they are valid during T2 through T4. S3 and S4 indicate which segment register was selected on the bus cycle, according to the following table. S2 0 (LOW) 0 0 0 1 (HIGH) 1 1 1 S1 0 0 1 1 0 0 1 1 S0 0 1 0 1 0 1 0 1 Characteristics Interrupt acknowledge Read I/O Write I/O Halt Instruciton Fetch Read Data from Memory Write Data to Memory Passive (no bus cycle) 0 1 (HIGH) 1 S4 0 (LOW) S3 0 1 0 1 Stack Code or None Data Characteristics Alternate Data (Extra segment) S5 indicates interrupt enable Flag. I/O Addressing The MSM80C86A-10 has 64 Kbytes of I/O or as 32 Kwords I/O. When the CPU accesses an I/ O device, addresses AD0 - AD15 are in the same format as a memory address, and A16 - A19 are low. The I/O ports addresses are same as memory, so it is necessary to be careful when using 8-bit peripherals. 21/37 ¡ Semiconductor Basic System Timing (4 + N*WAIT) = TCY T1 CLK T2 T3 TTWAIT T4 T1 MSM80C86A-10RS/GS/JS (4 + N*WAIT) = TCY T2 T3 TTWAIT T4 GOES INACTIVE IN THE STATE JUST PRIOR TO T4 ALE S2, S1, S0 BHE, A19 - A16 ADDR/ STATUS A15 - A0 ADDR/DATA S7 - S 3 BUS RESERVED FOR DATA IN A15 - A0 D15 - D0 VALID Data Out (D15 - D0) BHE, A19 - A16 S7 - S 3 RD, INTA READY READY WAIT DT/R WAIT READY DEN MEMORY ACCESS TIME WR 22/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS EXTERNAL INTERFACE Reset CPU Initialization is executed by the RESET pin. The MSM80C86A-10’s RESET High signal is required for greater than 4 clock cycles. The Rising edge of RESET terminates present operation immediately. The Falling edge of RESET triggers an internal reset sequence for approximately 10 clock cycles. After the internal reset sequence is finished normal operation occurs from absolute location FFFF0H. Interrupt Operations Interrupt operation is classified as software or hardware, and hardware interrupt is classified as non-maskable or maskable. An interrupt causes a new program location defined on the interrupt pointer table, according to the interrupt type. Absolute locations 00000H through 003FFH are reserved for the interrupt pointer table. The interrupt pointer table consists of 256-elements. Each element is 4 bytes in size and corresponds to an 8-bit type number which is sent from an interrupt request device during the interrupt acknowledge cycle. Non-maskable Interrupt (NMI) The MSM80C86A-10 has a Non-maskable interrupt (NMI) which is of higher priority than the markable interrupt request (INTR). The NMI request pulse width needs a minimum of 2 clock cycles. The NMI will be serviced at the end of the current instruction or between string manipulations. Maskable Interrupt (INTR) The MSM80C86A-10 provides another interrupt request (INTR) which can be masked by software. INTR is level triggered, so it must be held until the interrupt request is acknowledged. INTR will be serviced at the end of the current instruction or between string manipulations. Interrupt Acknowledge Sequence T1 T2 T3 T4 TI T1 T2 T3 T4 ALE LOCK INTA AD0 - AD15 Float Type Vector 23/37 ¡ Semiconductor Interrupt Acknowledge MSM80C86A-10RS/GS/JS During the interrupt acknowledge sequence, further interrupts are disabled. The interrupt enable bit is reset by any interrupt, after which the Flag register is automatically pushed onto the stack. During the acknowledge sequence, the CPU emits the lock signal from T2 of the first bus cycle to T2 of the second bus cycle. At second bus cycles, byte is fetched from the external device as a vector which identified the type of interrupt. This vector is multiplied by four and used as a interrupt pointer address. (INTR only) The interrupt Return (IRET) instruction includes a Flag pop operation which returns the original interrupt enable bit when it restores the Flag. HALT When a Halt instruction is executed, the CPU enters the Halt state. An interrupt request or RESET will force the MSM80C86A-10 out of the Halt state. System Timing – Minimum Mode A bus cycle begins T1 with an ALE signal. The trailing edge of ALE is used to latch the address. From T1 to T4 the M/IO signal indicates a memory or I/O operation. From T2 to T4, the address data bus changes the address but to data bus. The read (RD), write (WR) and interrupt acknowledge (INTA) signals causes the addressed device to enable data bus. These signal becomes active at the beginning of T2 and inactive at the beginning of T4. System Timing – Maximum Mode At maximum mode, the MSM82C88-2 Bus Controller is added to system. The CPU sends status information to the Bus Controller. Bus timing signals are generated by Bus Controller. Bus timing is almost the same as in the minimum mode. 24/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS BUS HOLD CIRCUITRY To avoid high current conditions caused by floating inputs to CMOS devices and to eliminate the need for pull-up/down resistors, “bus-hold” circuitry has been used on MSM80C86A-10 pins 2-16, 26-32, and 34-39 (Figures 6a, 6b). These circuits will maintain the last valid logic state if no driving source is present (i.e. an unconnected pin or a driving source which goes to a high impedance state). To overdrive the “bus hold” circuits, an external driver must be capable of supplying approximately 600 mA minimum sink or source current at valid input voltage levels. Since this “bus hold” circuitry is active and not a “resistive” type element, the associated power supply current is negligible and power dissipation is significantly reduced when compared to the use of passive pull-up resistors. "PULL-UP/PULL-DOWN" OUTPUT DRIVER BOND PAD EXTERNAL PIN INPUT BUFFER INPUT PROTECTION CIRCUITRY Input Buffer exists only on I/O pins Figure 6a. Bus Hold Circuitry Pin 2-16, 35-39 "PULL-UP" OUTPUT DRIVER BOND PAD EXTERNAL PIN VCC P INPUT BUFFER INPUT PROTECTION CIRCUITRY Input Buffer exists only on I/O pins Figure 6b. Bus Hold Circuitry Pin 26-32, 34 25/37 DATA TRANSFER 2 0 1 0 0 1 1 mod mod mod 1 1 0 r/m r/m r/m 1 11 reg 110 1 11 reg 111 1 1w reg 0 0 port w w port mod reg r/m mod 0 0 0 r/m w w 0 0 data data if w = 1 addr-high addr-high data if w = 1 7 1 1 1 1 1 1 1 1 0 0 1 0 0 1 1 1 1 1 1 1 1 0 0 0 1 1 1 0 0 0 0 0 1 0 0 0 1 0 001 011 0 reg 1 1 0 111 010 0 reg 6 0 1 0 0 0 0 0 5 0 0 1 1 1 0 0 4 0 0 1 0 0 0 0 3 1 0 w 0 0 1 1 1 d 1 reg 0 1 1 0 0 w w 76 mod mod 5 43 reg 000 data addr-low addr-low 0 reg 0 reg 2 10 r/m r/m 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 ¡ Semiconductor MOV = Move: Register/memory to/from register Immediate to register/memory Immediatye to register Memory to accumulator Accumulator to memory Register/memory to segment register Segment register to register/memory PUSH = Push: Register/memory Register Segment register POP = Pop: Register/memory Register Segment register XCHG = Exchange: Register/memory with register Register with accumulator IN = Input from: Fixed port Variable port OUT = Output to: Fixed port Variable port XLAT = Translate byte to AL LEA = Load EA to register LDS = Load pointer to DS LES = Load pointer to ES LAHF = Load AH with flags SAHF = Store AH into flags PUSHF = Push flags POPF = Pop flags 1 1 1 1 1 1 1 1 1 1 mod mod mod reg reg reg 1 1 1 0 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 1 1 1 0 1 0 1 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 1 1 0 0 w w 1 1 1 0 1 0 0 1 r/m r/m r/m MSM80C86A-10RS/GS/JS 26/37 ARITHMETIC mod mod 0 data data if w = 1 data if s:w = 01 0 1 0 reg 00 data r/m r/m mod mod 0 data data if w = 1 r/m r/m 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 d s 0 w w w ADD = Add: Reg./memory with register to either Immediate to register/memory Immediate to accumulator ¡ Semiconductor ADC = Add with carry: Reg./memory with register to either Immediate to register/memory Immediate to accumulator 0 1 0 1 0 0 0 mod mod 1 r/m r/m 1 1 0 0 1 0 1 1 1 0 1 0 1 0 0 0 1 1w reg 111 111 mod 0 0 0 r/m 0 0 0 0 0 0 1 0 1 0 0 0 0 0 1 d s 0 w w w reg 10 data data if s:w = 01 INC = Increment: Register/memory Register AAA = ASCII adjust for add DAA = Decimal adjust for add SUB = Subtract: Reg./memory with register to either Immediate from register/memory Immediate from accumulator 0 1 0 mod mod 0 r/m r/m 0 0 0 1 0 1 0 0 0 1 0 1 0 0 1 d s 0 w w w reg 01 data data data if w = 1 data if s:w = 01 SBB = Subtract with borrow: Reg./memory with register to either Immediate from register/memory Immediate from accumulator 0 1 0 1 0 1 mod mod mod 1 0 1 1 r/m r/m 1 1 1 1 0 1 1 0 1 1 1 0 1 1w reg 11w mod 0 0 1 r/m r/m 0 0 0 0 0 0 1 0 1 1 0 1 0 0 1 d s 0 w w w reg 11 data data data if w = 1 data if s:w = 01 DEC = Decrement: Register/memory Register NEG = Change sign CMP = Compare: Register/memory and register Immediate with register/memory Immediate with accumulator AAS = ASCII adjust for subtract 0 1 0 0 0 0 0 0 1 0 1 1 1 0 1 1 1 0 1 1 0 0 1 1 d s 0 1 w w w 1 reg 11 data data data if w = 1 data if s:w = 01 MSM80C86A-10RS/GS/JS 27/37 ¡ Semiconductor DAS = Decimal adjust for subtract MUL = Multiply (unsigned) IMUL = Integer multiply (signed) AAM = ASCII adjust for multiply DIV = Divide (unsigned) IDIV = Integer divide (signed) AAD = ASCII adjust for divide CBW = Convert byte to word CWD = Convert word to double word mod mod 00 mod mod 00 1 1 0 1 1 0 0 0 0 1 1 0 0 1 1 0 1 1 r/m r/m 010 r/m r/m 010 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 0 0 1 1 1 0 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 1 1 1 0 1 1 0 0 0 1 w w 0 w w 1 0 1 MSM80C86A-10RS/GS/JS 28/37 LOGIC 1 1 1 1 1 1 1 1 mod mod 1 data data if w = 1 r/m r/m 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 v v v v v v v w w w w w w w w mod mod mod mod mod mod mod mod 0 1 1 1 0 0 0 0 1 0 0 1 0 0 1 1 0 0 1 1 0 1 0 1 r/m r/m r/m r/m r/m r/m r/m r/m ¡ Semiconductor NOT = Invert SHL/SAL = Shift logical/arithmetic left SHR = Shift logical right SAR = Shift arithmetic right ROL = Rotate left ROR = Rotate right RCL = Rotate left through carry RCR = Rotate right through carry AND = And: Reg./memory and register to either Immediate to register/memory Immediate to accumulator 0 1 0 mod mod 0 data data if w = 1 r/m r/m 0 0 0 1 0 1 0 0 0 0 0 0 0 0 1 d 0 0 w w w reg 00 data data if w = 1 TEST = And function to flags, no result: Register/memory and register Immediate data and register/memory Immediate data and accumulator 1 1 1 mod mod 0 r/m r/m 0 1 0 0 1 1 0 1 0 0 0 1 1 1 0 0 1 0 w w w reg 00 data data if w = 1 OR = Or: Reg./memory and register to either Immediate to register/memory Immediate to accumulator 0 1 0 mod mod 1 r/m r/m 0 0 0 0 0 0 0 0 0 1 0 1 0 0 1 d 0 0 w w w reg 01 data data data if w = 1 data if w = 1 XOR = Exclusive or: Reg./memory and register to either Immediate to register/memory Immediate to accumulator 0 1 0 0 0 0 1 0 1 1 0 1 0 0 0 0 0 1 d 0 0 w w w reg 10 data data data if w = 1 data if w = 1 MSM80C86A-10RS/GS/JS 29/37 STRING MANIPULATION 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 1 1 1 0 0 1 type 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 0 0 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 1 0 1 disp disp disp disp disp disp disp disp disp disp disp disp disp disp disp disp disp disp disp disp 1 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 0 1 1 1 1 0 1 0 1 1 0 1 z w w w w w ¡ Semiconductor REP = Repeat MOVS = Move byte/word CMPS = Compare byte/word SCAS = Scan byte/word LODS = Load byte/word to AL/AX STOS = Store byte/word from AL/AX CJMP = Conditional JMP JE/JZ = Jump on equal/zero JZ/JNGE = Jump on less/not greater or equal JLE/JNG = Jump on less or equal/not greater JB/JNAE = Jump on below/not above or equal JBE/JNA = Jump on below or equal/not above JP/JPE = Jump on parity/parity even JO = Jump on over flow JS = Jump on sign JNE/JNZ = Jump on not equal/not zero JNL/JGE = Jump on not less/greater or equal JNLE/JG = Jump on not less or equal/greater JNB/JAE = Jump on not below/above or equal JNBE/JA = Jump on not below or equal/above JNP/JPO = Jump on not parity/parity odd JNO = Jump on not overflow JNS = Jump on not sign LOOP = Loop CX times LOOPZ/LOOPE = Loop while zero/equal LOOPNZ/LOOPNE = Loop while not zero equal JCXZ = Jump on CX zero INT = Interrupt Type specified Type 3 INTO = Interrupt on overflow IRET = Interrupt return MSM80C86A-10RS/GS/JS 30/37 ¡ Semiconductor PROCESSOR CONTROL CLC = Clear carry CMC = Complementary carry STC = Set carry CLD = Clear direction STD = Set direction CLI = Clear interrupt STI = Set interrupt HLT = Halt WAIT = Wait ESC = Escape ( to external device) LOCK = Bus lock prefix 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 0 1 1 0 0 1 0 1 1 0 0 1 0 x 0 0 0 0 0 0 1 1 0 1 x 0 0 1 1 0 1 0 1 0 1 x 0 mod x x x r/m CONTROL TRANSFER CALL = Call: Direct within segment Indirect within segment Direct intersegment Indirect intersegment JMP = Unconditional Jump: Direct within segment Direct within segment-short Indirect within segment Direct intersegment Indirect intersegment RET = Return from CALL: Within segment Within seg. adding immediate to SP Intersegment Intersegment adding immediate to SP 7 1 1 1 1 1 1 1 1 1 1 1 1 1 6 1 1 0 1 1 1 1 1 1 1 1 1 1 5 1 1 0 1 1 1 1 1 1 0 0 0 0 4 0 1 1 1 0 0 1 0 1 0 0 0 0 3 1 1 1 1 1 1 1 1 1 0 0 1 1 2 0 1 0 1 0 0 1 0 1 0 0 0 0 1 0 1 1 1 0 1 1 1 1 1 1 1 1 0 0 1 0 1 1 1 1 0 1 1 0 1 0 7 mod 6 543210 disp-low 010 r/m offset-low seg-low 011 r/m disp-low disp 100 offset-low seg-low 101 7 6 543 disp-high offset-high seg-high 2 1 0 7 6 5 43 2 1 0 mod disp-high r/m offset-high seg-high r/m mod MSM80C86A-10RS/GS/JS mod data-low data-low data-high dat-high 31/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS Foot Notes: AL = 8-bit accumulator AX = 18-bit accumulator CX = Count register DS = Data segment ES = Extra segment Above/below refers to unsigned value Greater=more positive Less=less positive (more negative) signed value If d=1 then “to” reg: If d=0 then “from” reg. If w=1 then word instruction: If w=0 then byte instruction If mod=11 then r/m is treated as a REG field If mod=00 then DISP=0*, disp-low and disp-high are absent If mod=01 then DISP=disp-low sign-extended to 16 bits, disp-high is absent If mod=10 then DISP=disp-high: disp-low If r/m=000 then EA=(BX)+(SI)+DISP If r/m=001 then EA=(BX)+(DI)+DISP If r/m=010 then EA=(BP)+(SI)+DISP If r/m=011 then EA=(BP)+(DI)+DISP If r/m=100 then EA=(SI)+DISP If r/m=101 then EA=(DI)+DISP If r/m=110 then EA=(BP)+DISP* If r/m=111 then EA=(BX)+DISP DISP follows 2nd byte of instruction (before data if required) * except if mod=00 and r/m=110 then EA-disp-high: disp-low If s:w=01 then 16 bits of immediate data form the operand If s:w=11 then an immediate data byte is sign extended to form the 16-bit operand If v=0 then “count”=1:if v=1 then “count” in (CL) x=don’ t care z is used for string primitives for comparison with ZF FLAG SEGMENT OVERRIDE PREFIX 001 reg 110 REG is assigned according to the following table: 16-Bit (w=1) 8-Bit (w=0) 000 AX 000 AL 001 CX 001 CL 010 DX 010 DL 011 BX 011 BL 100 SP 100 AH 101 BP 101 CH 110 SI 110 DH 111 DI 111 BH Segment 00 01 10 11 ES CS SS DS Instructions which reference the flag register file as a 16-bit object use the symbol FLAGS to represent the file: FLAGS=x:x:x:x:(OF):(DF):(IF):(TF):(SF):(ZF):X:(AF):X:(PF):X:(CF) 32/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS NOTICE ON REPLACING LOW-SPEED DEVICES WITH HIGH-SPEED DEVICES The conventional low speed devices are replaced by high-speed devices as shown below. When you want to replace your low speed devices with high-speed devices, read the replacement notice given on the next pages. High-speed device (New) M80C85AH M80C86A-10 M80C88A-10 M82C84A-2 M81C55-5 M82C37B-5 M82C51A-2 M82C53-2 M82C55A-2 Low-speed device (Old) M80C85A/M80C85A-2 M80C86A/M80C86A-2 M80C88A/M80C88A-2 M82C84A/M82C84A-5 M81C55 M82C37A/M82C37A-5 M82C51A M82C53-5 M82C55A-5 Remarks 8bit MPU 16bit MPU 8bit MPU Clock generator RAM.I/O, timer DMA controller USART Timer PPI 33/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS Differences between MSM80C86A-10 and MSM80C86A-2, MSM80C86A 1) Manufacturing Process All devices use a 1.5 m Si-CMOS process technology. 2) Design Although circuit timings of these devices are a little different, these devices have the same chip size and logics. 3) Electrical Characteristics Oki's '96 Data Book for MICROCONTROLLER describes that the MSM80C86A-10 satisfies the electrical characteristics of the MSM80C86A-2 and MSM80C86A. 4) Other notices 1) The noise characteristics of the high-speed MSM80C86A-10 (for 10 MHz) are a little different from those of the MSM80C86A-2 and MSM80C86A. Therefore when devices are replaced for upgrading, it is recommended to perform noise evaluation. 2) The characteristics of the MSM80C86A-10 basically satisfy those of the MSM80C86A-2 and MSM80C86A but their timings are a little different. When critical timing is required in designing it is recommended to evaluate operating margins at various temperatures and voltages. 34/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS PACKAGE DIMENSIONS (Unit : mm) DIP40-P-600-2.54 Package material Lead frame material Pin treatment Solder plate thickness Package weight (g) Epoxy resin 42 alloy Solder plating 5 mm or more 6.10 TYP. Notes for Mounting the Surface Mount Type Package The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact Oki’s responsible sales person for the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times). 35/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS (Unit : mm) QFJ44-P-S650-1.27 Mirror finish Package material Lead frame material Pin treatment Solder plate thickness Package weight (g) Epoxy resin Cu alloy Solder plating 5 mm or more 2.00 TYP. Notes for Mounting the Surface Mount Type Package The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact Oki’s responsible sales person for the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times). 36/37 ¡ Semiconductor MSM80C86A-10RS/GS/JS (Unit : mm) QFP56-P-1519-1.00-K Mirror finish Package material Lead frame material Pin treatment Solder plate thickness Package weight (g) Epoxy resin 42 alloy Solder plating 5 mm or more 1.46 TYP. Notes for Mounting the Surface Mount Type Package The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact Oki’s responsible sales person for the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times). 37/37