Pushbutton Switches/Indicators
A22R/M22R series
Robust and Graceful design
Pushbutton Switches
Push Button
This document provides information mainly for selecting suitable models. Please read the document Instruction Sheet carefully for information that the user must understand and
accept before purchase, including information on warranty, limitations of liability, and precautions.
OMRON Corporation
Industrial Automation Company
Sensing Devices Division H.Q.
Industrial Sensors Division
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 Japan
Tel: (81)75-344-7022/Fax: (81)75-344-7107
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69-2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,
IL 60173-5302 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
Authorized Distributor:
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark, Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
OMRON Industrial Automation Global: www.ia.omron.com
© OMRON Corporation 2009 All Rights Reserved.
In the interest of product improvement,
specifications are subject to change without notice.
Printed in Japan
Cat. No. A190-E1-01
1009
Secure and Human-centered
2
A22R/M22R Series Push Button
Responds with
high grade
illumination to
1
A22R/M22R Series Push Button
various needs
2
Round design
Soft to the touch
Gentle design for human.
Shining Metal Ring
4 Switch units
Provides shining and robust metal ring.
2 Switch units
4
3
Additional unit type
Switch unit can be added.
Compact size
The body length under a panel decreased by 15%
compare with our former products.
15% decrease
compare with the
current product
46.8 mm
3
2
A22R/M22R Series Push Button
Responds with
high grade
illumination to
1
A22R/M22R Series Push Button
various needs
2
Round design
Soft to the touch
Gentle design for human.
Shining Metal Ring
4 Switch units
Provides shining and robust metal ring.
2 Switch units
4
3
Additional unit type
Switch unit can be added.
Compact size
The body length under a panel decreased by 15%
compare with our former products.
15% decrease
compare with the
current product
46.8 mm
3
Lighted Type
4
A22R/M22R Series Push Button
A22R/M22R Series Push Button
Assembled Models
Non-l i gh t ed
Non-ligh
e d Type
Type
Operation Units
Lighted
L
ig h te d T
Type
yp e
N
Non-lighted
on-light ed Type
Flat type
A22R-F @ - @
Flat type
Projection type
Projection type
A22R-F @ - @ @
A22R-T @ - @ @
A22RL-T @ - @ - @ @
Light
Lighted
ed Type
Projection type
A22R-T @ - @
Select
or N
on-light ed Type
Selector
Non-lighted
Selec
torr N o n - l i g h t e d Type
Selecto
T y pe
Select
or Light
ed Ty
pe
Selector
Lighted
Type
Selector
Se
le cto r Lighted
L ig h te d Type
T yp e
2 notches
A22RS-2 @
2 notches
3 notches
2 notches
3 notches
A22RS-2 @ - @
A22RS-3 @ - @
A22RW-2 @ @ - @ - @
A22RW-3 @ @ - @ - @
Key Sel e ct
c t o r Type
Type
Projection type
A22RL-T @ - @
In
d ica to r
Indicator
3 notches
A22RS-3 @
Key Select
or
Selector
2 notches
A22RW-2 @ @
Sw
it ch U
nit
Switch
Unit
3 notches
A22RW-3 @ @
Soc
k et
Socket
Emergency Stop Switch
2 notches
A22RK-2 @
2 notches
3 notches
Indicator
*Emergency
A22RK-2 @ - @
A22RK-3 @ - @
M22R-E @ - @
A22E- @ - @ - @ - @
3 notches
A22RK-3 @
Switch with Lamp socket
A22RL- @ M - @
Switch Block
Lamp Socket
Mounting Plate
Switch block
A22R- @
Lamp socket
A22R- @
Mounting plate
A22R-3200
Socket
A22R- @ M
LED
* Refer to the Safety Components Series Catalog (Cat. No. Y106) for detail.
LED
A22R - @ @
5
Lighted Type
4
A22R/M22R Series Push Button
A22R/M22R Series Push Button
Assembled Models
Non-l i gh t ed
Non-ligh
e d Type
Type
Operation Units
Lighted
L
ig h te d T
Type
yp e
N
Non-lighted
on-light ed Type
Flat type
A22R-F @ - @
Flat type
Projection type
Projection type
A22R-F @ - @ @
A22R-T @ - @ @
A22RL-T @ - @ - @ @
Light
Lighted
ed Type
Projection type
A22R-T @ - @
Select
or N
on-light ed Type
Selector
Non-lighted
Selec
torr N o n - l i g h t e d Type
Selecto
T y pe
Select
or Light
ed Ty
pe
Selector
Lighted
Type
Selector
Se
le cto r Lighted
L ig h te d Type
T yp e
2 notches
A22RS-2 @
2 notches
3 notches
2 notches
3 notches
A22RS-2 @ - @
A22RS-3 @ - @
A22RW-2 @ @ - @ - @
A22RW-3 @ @ - @ - @
Key Sel e ct
c t o r Type
Type
Projection type
A22RL-T @ - @
In
d ica to r
Indicator
3 notches
A22RS-3 @
Key Select
or
Selector
2 notches
A22RW-2 @ @
Sw
it ch U
nit
Switch
Unit
3 notches
A22RW-3 @ @
Soc
k et
Socket
Emergency Stop Switch
2 notches
A22RK-2 @
2 notches
3 notches
Indicator
*Emergency
A22RK-2 @ - @
A22RK-3 @ - @
M22R-E @ - @
A22E- @ - @ - @ - @
3 notches
A22RK-3 @
Switch with Lamp socket
A22RL- @ M - @
Switch Block
Lamp Socket
Mounting Plate
Switch block
A22R- @
Lamp socket
A22R- @
Mounting plate
A22R-3200
Socket
A22R- @ M
LED
* Refer to the Safety Components Series Catalog (Cat. No. Y106) for detail.
LED
A22R - @ @
5
A22R/M22R Series Push Button
Assembled Models
Assembled Models
Pushbutt
Pus
hbutt o
on
n Switc
che
hes
Selector
Select
or Switches
Sw it ches
● Non-lighted/Lighted
1b
A22R-FB-01@
1b
A22R-FR-01@
1a
A22R-TW-10@
1a
A22R-TB-10@
A22R-TY-10@
1a
A22R-TA-10@
1b
A22R-TB-01@
1b
A22R-TR-01@
A22RW-2@@-@-@
2 notches
AC, DC 24V
Projection
46.8
A22RW-3@@-@-@
3 notches
AC, DC 24V
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22RL-TG-24A-10@
1a
A22RL-TR-24A-10@
1a
A22RL-TY-24A-10@
1a
A22RL-TA-24A-10@
1a
A22RL-TW-T2-10@
1a
A22RL-TG-T2-10@
1a
A22RL-TR-T2-10@
1a
A22RL-TY-T2-10@
1a
A22RL-TA-T2-10@
29.8
23.7
Projection
AC 220V
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
46.8
0.5
1a
16.7
A22RL-TW-24A-10@
6
Projection
AC, DC 24V
1a
10
A22RL-T@-@-@@
A22RS-3M-20
2a
A22RS-3A-20
29.8
1a
A22RW-2MG-24A-10
1a1b
A22RW-2MR-24A-11
1a
A22RW-2AY-24A-10
1a1b
A22RW-2AA-24A-11
2a
A22RW-3MG-24A-20
2a
A22RW-3MR-24A-20
2a
A22RW-3AY-24A-20
2a
A22RW-3AA-24A-20
29.8
6
1a
2a
3 notches
0.5
A22R-TR-01@
A22RS-2A-11
* These Non-lighted types provide black knobs.
29.8
16.7
10
1a
1a1b
6
A22R-TG-10@
A22RS-2A-10
29.8
29.8
23.7
1a
1a
24.2
A22R-FA-10@
A22RS-3@-@
A22RS-2M-11
10
1a
29.8
1a1b
28°
R2
7
0.5
A22R-FY-10@
A22RS-2M-10
6
1a
Dimensions
46.8
A22R-FR-10@
Part No.
24.2
1a
Contact
form
0.5
A22R-FG-10@
36
2 notches
1a
Knob
Knob
position color
1a
A22RS-2@-@
R2
7
A22R-FB-10@
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22R-T@-@@
Number
of notch
10
Round/Flat
Appearance
28°
A22R-FW-10@
10
1a
Dimensions
0.5
1a
A22R-F@-@@
Part No.
10.8
Contact
form
6
Pushbutton
color
46.8
Pushbutton
shape
36
● Non-lighted/Lighted
Appearance
7
A22R/M22R Series Push Button
46.8
6
A22R/M22R Series Push Button
Assembled Models
Assembled Models
Pushbutt
Pus
hbutt o
on
n Switc
che
hes
Selector
Select
or Switches
Sw it ches
● Non-lighted/Lighted
1b
A22R-FB-01@
1b
A22R-FR-01@
1a
A22R-TW-10@
1a
A22R-TB-10@
A22R-TY-10@
1a
A22R-TA-10@
1b
A22R-TB-01@
1b
A22R-TR-01@
A22RW-2@@-@-@
2 notches
AC, DC 24V
Projection
46.8
A22RW-3@@-@-@
3 notches
AC, DC 24V
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22RL-TG-24A-10@
1a
A22RL-TR-24A-10@
1a
A22RL-TY-24A-10@
1a
A22RL-TA-24A-10@
1a
A22RL-TW-T2-10@
1a
A22RL-TG-T2-10@
1a
A22RL-TR-T2-10@
1a
A22RL-TY-T2-10@
1a
A22RL-TA-T2-10@
29.8
23.7
Projection
AC 220V
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
46.8
0.5
1a
16.7
A22RL-TW-24A-10@
6
Projection
AC, DC 24V
1a
10
A22RL-T@-@-@@
A22RS-3M-20
2a
A22RS-3A-20
29.8
1a
A22RW-2MG-24A-10
1a1b
A22RW-2MR-24A-11
1a
A22RW-2AY-24A-10
1a1b
A22RW-2AA-24A-11
2a
A22RW-3MG-24A-20
2a
A22RW-3MR-24A-20
2a
A22RW-3AY-24A-20
2a
A22RW-3AA-24A-20
29.8
6
1a
2a
3 notches
0.5
A22R-TR-01@
A22RS-2A-11
* These Non-lighted types provide black knobs.
29.8
16.7
10
1a
1a1b
6
A22R-TG-10@
A22RS-2A-10
29.8
29.8
23.7
1a
1a
24.2
A22R-FA-10@
A22RS-3@-@
A22RS-2M-11
10
1a
29.8
1a1b
28°
R2
7
0.5
A22R-FY-10@
A22RS-2M-10
6
1a
Dimensions
46.8
A22R-FR-10@
Part No.
24.2
1a
Contact
form
0.5
A22R-FG-10@
36
2 notches
1a
Knob
Knob
position color
1a
A22RS-2@-@
R2
7
A22R-FB-10@
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22R-T@-@@
Number
of notch
10
Round/Flat
Appearance
28°
A22R-FW-10@
10
1a
Dimensions
0.5
1a
A22R-F@-@@
Part No.
10.8
Contact
form
6
Pushbutton
color
46.8
Pushbutton
shape
36
● Non-lighted/Lighted
Appearance
7
A22R/M22R Series Push Button
46.8
6
8
A22R/M22R Series Key/Signal Indicator/Construction
A22R/M22R Series Key/Signal Indicator/Construction
Assembled Models
Structure
Selector
tor S w i t ch
ches
Selec
A22R ser ies
● Key Selector
Number
of notch
Key
position
Contact
form
1a
A22RK-2@-@
2 notches
Part No.
Dimensions
A22RK-2ML-10
1a1b
A22RK-2ML-11
1a
A22RK-2M-10
1a1b
A22RK-2M-11
1a
A22RK-2AL-10
1a1b
A22RK-2AL-11
Pushbutton unit
28°
R2
7
36
Appearance
29.8
27
: key release position
2a
A22RK-3M-20
2a
A22RK-3MC-20
2a
A22RK-3AC-20
LED
Lighting source
• LED
0.5
A22RK-3ML-20
19
2a
10
A22RK-3@-@
6
3 notches
46.8
Body unit
: key release position
Contact form
• 1a,1b
Lighting method
• Non-lighted
• Without voltage-reduction unit
• With voltage reduction unit
I ndi c ator
Indicator
● All-in-one type
LED rating
Indicator
color
Part No.
Dimensions
M22R-EG-24A
AC, DC 24V
Indicator
M22R-ER-24A
Lighting source
• LED
0.5
M22R-EA-24A
14.4
M22R-EY-24A
M22R-EW-T2
M22R-ER-T2
M22R-EY-T2
M22R-EA-T2
6
M22R-EG-T2
AC 220V
M22R ser ies
29.8
M22R-EW-24A
M22R-E@-@
40.5
Appearance
9
8
A22R/M22R Series Key/Signal Indicator/Construction
A22R/M22R Series Key/Signal Indicator/Construction
Assembled Models
Structure
Selector
tor S w i t ch
ches
Selec
A22R ser ies
● Key Selector
Number
of notch
Key
position
Contact
form
1a
A22RK-2@-@
2 notches
Part No.
Dimensions
A22RK-2ML-10
1a1b
A22RK-2ML-11
1a
A22RK-2M-10
1a1b
A22RK-2M-11
1a
A22RK-2AL-10
1a1b
A22RK-2AL-11
Pushbutton unit
28°
R2
7
36
Appearance
29.8
27
: key release position
2a
A22RK-3M-20
2a
A22RK-3MC-20
2a
A22RK-3AC-20
LED
Lighting source
• LED
0.5
A22RK-3ML-20
19
2a
10
A22RK-3@-@
6
3 notches
46.8
Body unit
: key release position
Contact form
• 1a,1b
Lighting method
• Non-lighted
• Without voltage-reduction unit
• With voltage reduction unit
I ndi c ator
Indicator
● All-in-one type
LED rating
Indicator
color
Part No.
Dimensions
M22R-EG-24A
AC, DC 24V
Indicator
M22R-ER-24A
Lighting source
• LED
0.5
M22R-EA-24A
14.4
M22R-EY-24A
M22R-EW-T2
M22R-ER-T2
M22R-EY-T2
M22R-EA-T2
6
M22R-EG-T2
AC 220V
M22R ser ies
29.8
M22R-EW-24A
M22R-E@-@
40.5
Appearance
9
10
A22R/M22R Series Push Button
A22R/M22R Series Push Button
Individual Unit
Individual Unit
Selector
Select
or unit
Pushbutt
P
us hbutt o n u n i t
● Non-lighted/Lighted
Appearance
● Non-lighted/Lighted
Pushbutton
shape
Pushbutton
color
Part No.
Dimensions
A22R-FW-@
A22R-F@-@
29.8
Appearance
Number
of notch
A22RS-2@
Knob
Knob
position color
Part No.
Dimensions
29.8
A22RS-2M
A22R-FB-@
A22RS-2A
A22R-FG-@
2 notches
A22R-FR-@
Round/Flat
0.5
* These Non-lighted types provide black knobs.
22
6
3 notches
24.2
A22RS-3A
10
0.5
10.8
6
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22RS-3M
A22RS-3@
22
A22R-FA-@
10
A22R-FY-@
A22R-TW-@
A22R-T@-@
0.5
A22RW-2MY
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22RW-2MA
A22RW-2AG
10
A22RW-2AR
A22RL-TW-@
A22RL-T@-@
A22RW-2AY
0.5
A22RW-3MG
A22RW-3@
6
A22RL-TY-@
A22RL-TA-@
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22RW-3MR
3 notches
Lighted
Type
A22RW-3MY
A22RW-3AA
A22RW-3AG
A22RW-3AR
22
A22RW-2AA
22
Projection
Lighted type
16.7
10
A22RL-TR-@
6
A22RL-TG-@
0.5
2 notches
Lighted
Type
A22R-TA-@
24.2
A22R-TY-@
A22RW-2MR
6
A22R-TR-@
A22RW-2MG
A22RW-2@
22
A22R-TG-@
16.7
10
A22R-TB-@
Projection
11
10
A22R/M22R Series Push Button
A22R/M22R Series Push Button
Individual Unit
Individual Unit
Selector
Select
or unit
Pushbutt
P
us hbutt o n u n i t
● Non-lighted/Lighted
Appearance
● Non-lighted/Lighted
Pushbutton
shape
Pushbutton
color
Part No.
Dimensions
A22R-FW-@
A22R-F@-@
29.8
Appearance
Number
of notch
A22RS-2@
Knob
Knob
position color
Part No.
Dimensions
29.8
A22RS-2M
A22R-FB-@
A22RS-2A
A22R-FG-@
2 notches
A22R-FR-@
Round/Flat
0.5
* These Non-lighted types provide black knobs.
22
6
3 notches
24.2
A22RS-3A
10
0.5
10.8
6
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22RS-3M
A22RS-3@
22
A22R-FA-@
10
A22R-FY-@
A22R-TW-@
A22R-T@-@
0.5
A22RW-2MY
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22RW-2MA
A22RW-2AG
10
A22RW-2AR
A22RL-TW-@
A22RL-T@-@
A22RW-2AY
0.5
A22RW-3MG
A22RW-3@
6
A22RL-TY-@
A22RL-TA-@
Insert one of the following letters into the box @.
M: Momentary
A: Alternate
A22RW-3MR
3 notches
Lighted
Type
A22RW-3MY
A22RW-3AA
A22RW-3AG
A22RW-3AR
22
A22RW-2AA
22
Projection
Lighted type
16.7
10
A22RL-TR-@
6
A22RL-TG-@
0.5
2 notches
Lighted
Type
A22R-TA-@
24.2
A22R-TY-@
A22RW-2MR
6
A22R-TR-@
A22RW-2MG
A22RW-2@
22
A22R-TG-@
16.7
10
A22R-TB-@
Projection
11
A22R/M22R Series Key/Switch Section/Mounting Console
Individual Unit
Individual Unit
Switch
Sw
it ch / Lamp units
unit s
Selector
Selec
tor u n i t
● Switch unit
Number
of notch
Key position
Part No.
Appearance
Dimensions
Unit
A22R-@
A22RK-2@
29.8
A22RK-2ML
Contact
block
A22RK-2M
Contact form
Part No.
1a
A22R-10
1b
A22R-01
Dimensions
9.8
5.6
4
* Additional one block can be mountet to make 2a, 2b, or
1a1b.
26.5
● Key Selector
Appearance
13
A22R/M22R Series Key/Switch Section/Mounting Console
23.5
12
2 notches
A22RK-2AL
36
: key release position
● Lamp socket
27
A22RK-3@
A22RK-3ML
Appearance
Unit
Rating
Part No.
Dimensions
A22RK-3M
22
6
With voltage
reduction unit
AC220V
A22R-T2
Lamp socket
: key release position
26.5
A22RK-3AC
A22R-TN
23.5
A22RK-3MC
10.3
Without voltage
reduction unit
AC/DC6V, AC/DC12V,
AC/DC24V
16.3
A22R-@
19
10
0.5
3 notches
9.8
36
Switch
Switc
h un
unii t
● For Lighted type
Standard
AC 220V
Part No.
1a
A22RL-10M
1b
A22RL-01M
2a
A22RL-20M
2b
1a1b
A22RL-02M
A22RL-11M
1a
A22RL-10M-T2
1b
A22RL-01M-T2
2a
A22RL-20M-T2
2b
1a1b
A22RL-02M-T2
A22RL-11M-T2
Mounting
Mount
ing plate
plat e
Dimensions
29.8
Appearance
10.3
Socket
28°
Mounting
plate
A22R-3200
29.8
Contact form
Part No.
Dimensions
1a
A22R-10M
29.8
1b
A22R-01M
2a
A22R-20M
1a1b
A22R-11M
2b
A22R-02M
10.5
A22R-@M
Dimensions
R2
7
33.5
Type
Part No.
A22R-3200
● For Non-lighted type
Appearance
Unit
36
A22RL-@M-@
Contact form
6.3
Type
39.8
Appearance
A22R/M22R Series Key/Switch Section/Mounting Console
Individual Unit
Individual Unit
Switch
Sw
it ch / Lamp units
unit s
Selector
Selec
tor u n i t
● Switch unit
Number
of notch
Key position
Part No.
Appearance
Dimensions
Unit
A22R-@
A22RK-2@
29.8
A22RK-2ML
Contact
block
A22RK-2M
Contact form
Part No.
1a
A22R-10
1b
A22R-01
Dimensions
9.8
5.6
4
* Additional one block can be mountet to make 2a, 2b, or
1a1b.
26.5
● Key Selector
Appearance
13
A22R/M22R Series Key/Switch Section/Mounting Console
23.5
12
2 notches
A22RK-2AL
36
: key release position
● Lamp socket
27
A22RK-3@
A22RK-3ML
Appearance
Unit
Rating
Part No.
Dimensions
A22RK-3M
22
6
With voltage
reduction unit
AC220V
A22R-T2
Lamp socket
: key release position
26.5
A22RK-3AC
A22R-TN
23.5
A22RK-3MC
10.3
Without voltage
reduction unit
AC/DC6V, AC/DC12V,
AC/DC24V
16.3
A22R-@
19
10
0.5
3 notches
9.8
36
Switch
Switc
h un
unii t
● For Lighted type
Standard
AC 220V
Part No.
1a
A22RL-10M
1b
A22RL-01M
2a
A22RL-20M
2b
1a1b
A22RL-02M
A22RL-11M
1a
A22RL-10M-T2
1b
A22RL-01M-T2
2a
A22RL-20M-T2
2b
1a1b
A22RL-02M-T2
A22RL-11M-T2
Mounting
Mount
ing plate
plat e
Dimensions
29.8
Appearance
10.3
Socket
28°
Mounting
plate
A22R-3200
29.8
Contact form
Part No.
Dimensions
1a
A22R-10M
29.8
1b
A22R-01M
2a
A22R-20M
1a1b
A22R-11M
2b
A22R-02M
10.5
A22R-@M
Dimensions
R2
7
33.5
Type
Part No.
A22R-3200
● For Non-lighted type
Appearance
Unit
36
A22RL-@M-@
Contact form
6.3
Type
39.8
Appearance
14
A22R/M22R Series LED/Button/Knob/Key/Signal Indicator
A22R/M22R Series LED/Button/Knob/Key/Signal Indicator
Individual Unit
Nomenclature
Lamp unit
uni t
Nomenclature
N
omenclat ure
● LED
● Completely Assembled A22R@-@@-@-@@ Pushbutton switches
LED operating
voltage
Lighting color
Part No.
Dimensions
➀ Lighting
A22R-6AW
A22R-@@
LED
AC/DC6V
A22R@—@@—@—@@
➀
➁ ➂
➃
➄ ➅
➁ Pushbutton Shape ➂ Lighting Color ➃ Light Source
A22R-6AG
Code Lighting
Code
Shape
Code Color
F
A22R-6AR
NonBlank
lighted
Flat *
R
Red
G
Y
W
Yellow
White
L
A22R-6AY
Lighted
T Projection
* For Non-lighted
type only
A22R-6AA
A
A22R-12AW
9.6
A22R-12AG
LED
AC/DC12V
A22R-12AR
B
Green
Blank No light source
AC/DC6V
6A
12A
AC/DC12V
24A
Blue
Black *
Code
Operating
Voltage
T2
AC220V
9.3
A22R-24AG
A22R-24AR
A22R-24AY
A22R-24AA
Code
Contact
Form
10
1a
01
11
20
1b
1a1b
2a
02
2b
Code Switch Operation
M
Momentary action
A
Alternate action
Use AC/DC24V LED
A22R-12AA
LED
AC/DC24V
AC/DC24V
➃ Light Source
A22R-12AY
A22R-24AW
➄ Contact Form ➅ Switch Operation
Operating
Voltage
Code
* For Non-lighted
type only
BA9S/13
20
Appearance
15
● Completely Assembled A22R@-@@-@-@ Selector switches
A22R@—@@—@—@
➀
➁➂
➃
➄
➀ Lighting
Code Lighting
S
Nonlighted
W
Lighted
➁ Number of Notches/Reset Method ➂ Lighting Color
Code
2M
2A
3M
3A
3MA
3AM
Specification
Code Color
Blank Black*
2 notches/Manual
2 notches/Automatic
3 notches/Manual
3 notches/Automatic
3 notches/Manual –
left side, Automatic –
right side
3 notches/Automatic –
left side, Manual –
right side
R
Red
G
Green
Y
A
Yellow
2ML
2M
2AL
3ML
3M
Number of notches, Reset
method, Key release position
2 notches, Manual, Left
2 notches, Manual, Left and Right
2 notches, Automatic, Left
3 notches, Manual, Left
3 notches, Manual, Left and Right
3MC 3 notches, Manual, Center
3AC 3 notches, Automatic, Center
3 notches, Manual – left,
3MAL
Automatic - right, Left
3 notches, Automatic –
3AMR
left, Manual – right, Right
Operating Voltage
Blank
No-lighted type
10
1a**
6A
12A
24A
AC/DC6V
AC/DC12V
AC/DC24V
01
11
20
1a1b
2a
02
2b
Code Contact Form
➃ Light Source
Code
Operating Voltage
1b**
** For models with 2
notches
AC220V
T2
Use AC/DC24V LED
● Completely Assembled M22R-@@-@
Indicator
M22R—@@—@
➀ ➁
➂
A22RK—@—@
➀
➁
Code
➄ Contact Form
Code
Blue
* Non-lighted type
only
● Completely Assembled A22RK-@-@
Key selector switches
➀ Number of Notches/Reset method
➃ Light Source
➁ Contact Form
Code
Contact
Form
10
01
11
20
02
1a**
1b**
1a1b
2a
2b
** For models
with 2 notches
➀ Structure
Code Type
All-inE
one type
➁ Lighting Color
Lighting
Code
Color
➂ Light Source
R
Red
Operating
Voltage
12A AC/DC12V
G
Y
W
Green
24A AC/DC24V
Yellow
White
A
Blue
Code
➂ Voltage Reduction
Unit
Operating
Code
Voltage
T2
AC220V
14
A22R/M22R Series LED/Button/Knob/Key/Signal Indicator
A22R/M22R Series LED/Button/Knob/Key/Signal Indicator
Individual Unit
Nomenclature
Lamp unit
uni t
Nomenclature
N
omenclat ure
● LED
● Completely Assembled A22R@-@@-@-@@ Pushbutton switches
LED operating
voltage
Lighting color
Part No.
Dimensions
➀ Lighting
A22R-6AW
A22R-@@
LED
AC/DC6V
A22R@—@@—@—@@
➀
➁ ➂
➃
➄ ➅
➁ Pushbutton Shape ➂ Lighting Color ➃ Light Source
A22R-6AG
Code Lighting
Code
Shape
Code Color
F
A22R-6AR
NonBlank
lighted
Flat *
R
Red
G
Y
W
Yellow
White
L
A22R-6AY
Lighted
T Projection
* For Non-lighted
type only
A22R-6AA
A
A22R-12AW
9.6
A22R-12AG
LED
AC/DC12V
A22R-12AR
B
Green
Blank No light source
AC/DC6V
6A
12A
AC/DC12V
24A
Blue
Black *
Code
Operating
Voltage
T2
AC220V
9.3
A22R-24AG
A22R-24AR
A22R-24AY
A22R-24AA
Code
Contact
Form
10
1a
01
11
20
1b
1a1b
2a
02
2b
Code Switch Operation
M
Momentary action
A
Alternate action
Use AC/DC24V LED
A22R-12AA
LED
AC/DC24V
AC/DC24V
➃ Light Source
A22R-12AY
A22R-24AW
➄ Contact Form ➅ Switch Operation
Operating
Voltage
Code
* For Non-lighted
type only
BA9S/13
20
Appearance
15
● Completely Assembled A22R@-@@-@-@ Selector switches
A22R@—@@—@—@
➀
➁➂
➃
➄
➀ Lighting
Code Lighting
S
Nonlighted
W
Lighted
➁ Number of Notches/Reset Method ➂ Lighting Color
Code
2M
2A
3M
3A
3MA
3AM
Specification
Code Color
Blank Black*
2 notches/Manual
2 notches/Automatic
3 notches/Manual
3 notches/Automatic
3 notches/Manual –
left side, Automatic –
right side
3 notches/Automatic –
left side, Manual –
right side
R
Red
G
Green
Y
A
Yellow
2ML
2M
2AL
3ML
3M
Number of notches, Reset
method, Key release position
2 notches, Manual, Left
2 notches, Manual, Left and Right
2 notches, Automatic, Left
3 notches, Manual, Left
3 notches, Manual, Left and Right
3MC 3 notches, Manual, Center
3AC 3 notches, Automatic, Center
3 notches, Manual – left,
3MAL
Automatic - right, Left
3 notches, Automatic –
3AMR
left, Manual – right, Right
Operating Voltage
Blank
No-lighted type
10
1a**
6A
12A
24A
AC/DC6V
AC/DC12V
AC/DC24V
01
11
20
1a1b
2a
02
2b
Code Contact Form
➃ Light Source
Code
Operating Voltage
1b**
** For models with 2
notches
AC220V
T2
Use AC/DC24V LED
● Completely Assembled M22R-@@-@
Indicator
M22R—@@—@
➀ ➁
➂
A22RK—@—@
➀
➁
Code
➄ Contact Form
Code
Blue
* Non-lighted type
only
● Completely Assembled A22RK-@-@
Key selector switches
➀ Number of Notches/Reset method
➃ Light Source
➁ Contact Form
Code
Contact
Form
10
01
11
20
02
1a**
1b**
1a1b
2a
2b
** For models
with 2 notches
➀ Structure
Code Type
All-inE
one type
➁ Lighting Color
Lighting
Code
Color
➂ Light Source
R
Red
Operating
Voltage
12A AC/DC12V
G
Y
W
Green
24A AC/DC24V
Yellow
White
A
Blue
Code
➂ Voltage Reduction
Unit
Operating
Code
Voltage
T2
AC220V
16
A22R/M22R Series Switch Section/ Indicator Section/LED
A22R/M22R Series Switch Section/ Indicator Section/LED
Individual Unit
Nomenclature
Nomenc
Nomencll a
att u r e
N omenclat ure
Nomenclature
● Individual unit (Switch unit) A22R@-@M-@
● Individual unit (Pushbutton unit) A22R@-@@-@ Pushbutton switches
A22R@—@M—@
➀
➁➂
➃
A22R@—@@—@
➀
➁➂
➃
➀ Lighting
Code
Lighting
Blank Non-lighted
L
Lighted
➁ Pushbutton Shape
➂ Pushbutton Color
Code Pushbutton Shape
F
Flat*
T
Projection
*For Non-lighted type only
➃ Switch Operation
Code Pushbutton Color
Code Switch Operation
➀ Lighting
Code
Lighting
Blank Non-lighted
➁ Contact Form
➂ Switch Operation
Code Contact Form
Code Switch Operation
10
1a
Yellow
White
01
11
20
1a1b
2a
Blue
02
2b
R
Red
M
Momentary action
G
Y
W
Green
A
Alternate action
A
L
Lighted
M
➃ Voltage Reduction Unit
Momentary action
Code Operation Voltage
Blank Non-lighted type
AC220V*
T2
1b
*Use with an A22R-24@LED
B
Black*
*For Non-lighted type only
● Individual unit (Switch block) A22R-@
● Individual unit (Selector unit) A22R@-@@ Selector switches
A22R@—@@
➀
➁ ➂
➀ Lighting
Code
Lighting
S
Non-lighted
W
Lighted
➁ Number of notches, Reset Method
Number of notches, Reset Method
2M 2 notches, Manual
2A 2 notches, Automatic
3M 3 notches, Manual
3A 3 notches, Automatic
3MA 3 notches, Manual – left, Automatic – right
3AM 3 notches, Automatic – left, Manual - right
● Individual unit (Key selector unit) A22RK-@ Key selector switches
A22RK—@
➀
➀ Number of notches, Reset Method, Key Release Position
Code Number of notches, Reset Method, Key Release Position
2ML 2 notches, Manual, Left
2M 2 notches, Manual, Left and Right
2AL 2 notches, Automatic, Left
3ML 3 notches, Manual, Left
3M 3 notches, Manual, Left and Right
3MC 3 notches, Manual, Center
3AC 3 notches, Automatic, Center
3MAL 3 notches, Manual – left, Automatic – right, Left
3AMR 3 notches, Automatic – left, Manual – right, Right
➂ Knob Color
Code Color
Blank Black*
Red
R
G
Y
Green
Yellow
A
Blue
● Individual unit (Voltage-reduction unit) A22R-@
A22R—@
➀
A22R—@
➀
Code
17
➀ Contact Form
➀ Body unit
Code Contact Form
10
1a
01
1b
Code Operating Voltage
TN
AC/DC6V,
AC/DC12V,
AC/DC24V
T2
AC220V*
*Use with an A22R-24@LED
*Non-lighted type
● Individual unit (LED) A22R-@ @ LED
A22R—@@
➀ ➁
➀ Operating Voltage
Code Operating Voltage
6A AC/DC6V
12A AC/DC12V
24A AC/DC24V
➁ Lighting color
Code Lighting color
R
Red
G
Y
W
Green
Yellow
White
A
Blue
16
A22R/M22R Series Switch Section/ Indicator Section/LED
A22R/M22R Series Switch Section/ Indicator Section/LED
Individual Unit
Nomenclature
Nomenc
Nomencll a
att u r e
N omenclat ure
Nomenclature
● Individual unit (Switch unit) A22R@-@M-@
● Individual unit (Pushbutton unit) A22R@-@@-@ Pushbutton switches
A22R@—@M—@
➀
➁➂
➃
A22R@—@@—@
➀
➁➂
➃
➀ Lighting
Code
Lighting
Blank Non-lighted
L
Lighted
➁ Pushbutton Shape
➂ Pushbutton Color
Code Pushbutton Shape
F
Flat*
T
Projection
*For Non-lighted type only
➃ Switch Operation
Code Pushbutton Color
Code Switch Operation
➀ Lighting
Code
Lighting
Blank Non-lighted
➁ Contact Form
➂ Switch Operation
Code Contact Form
Code Switch Operation
10
1a
Yellow
White
01
11
20
1a1b
2a
Blue
02
2b
R
Red
M
Momentary action
G
Y
W
Green
A
Alternate action
A
L
Lighted
M
➃ Voltage Reduction Unit
Momentary action
Code Operation Voltage
Blank Non-lighted type
AC220V*
T2
1b
*Use with an A22R-24@LED
B
Black*
*For Non-lighted type only
● Individual unit (Switch block) A22R-@
● Individual unit (Selector unit) A22R@-@@ Selector switches
A22R@—@@
➀
➁ ➂
➀ Lighting
Code
Lighting
S
Non-lighted
W
Lighted
➁ Number of notches, Reset Method
Number of notches, Reset Method
2M 2 notches, Manual
2A 2 notches, Automatic
3M 3 notches, Manual
3A 3 notches, Automatic
3MA 3 notches, Manual – left, Automatic – right
3AM 3 notches, Automatic – left, Manual - right
● Individual unit (Key selector unit) A22RK-@ Key selector switches
A22RK—@
➀
➀ Number of notches, Reset Method, Key Release Position
Code Number of notches, Reset Method, Key Release Position
2ML 2 notches, Manual, Left
2M 2 notches, Manual, Left and Right
2AL 2 notches, Automatic, Left
3ML 3 notches, Manual, Left
3M 3 notches, Manual, Left and Right
3MC 3 notches, Manual, Center
3AC 3 notches, Automatic, Center
3MAL 3 notches, Manual – left, Automatic – right, Left
3AMR 3 notches, Automatic – left, Manual – right, Right
➂ Knob Color
Code Color
Blank Black*
Red
R
G
Y
Green
Yellow
A
Blue
● Individual unit (Voltage-reduction unit) A22R-@
A22R—@
➀
A22R—@
➀
Code
17
➀ Contact Form
➀ Body unit
Code Contact Form
10
1a
01
1b
Code Operating Voltage
TN
AC/DC6V,
AC/DC12V,
AC/DC24V
T2
AC220V*
*Use with an A22R-24@LED
*Non-lighted type
● Individual unit (LED) A22R-@ @ LED
A22R—@@
➀ ➁
➀ Operating Voltage
Code Operating Voltage
6A AC/DC6V
12A AC/DC12V
24A AC/DC24V
➁ Lighting color
Code Lighting color
R
Red
G
Y
W
Green
Yellow
White
A
Blue
18
A22R/M22R Series
A22R/M22R Series
Accessories / Tools
Accessories / Tools
Items
IItems
t ems
● Accessories
● Accessories
Item
Standard
size
Appearance
Classification
Part No.
White
A22Z-3321
Red
A22Z-3322
With Snap-in Legend
Plate (without text)
Without Snap-in Legend Plate
Large
size
Red
A22Z-3332
Round
A22Z-3360
A22Z-3600F
Sealing Caps
For projection models
Connectors
A22Z-3600T
A22Z-3530
One hole
A22Z-B101
Two holes
A22Z-B102
Three holes
Applicable
diameter
(mm)
Part No.
A22Z-3443B
Red
A22Z-3443R
White
A22Z-3443W
Transparent
A22Z-3443C
White text
on red
background
A22Z-3443R-2
STOP
A22Z-3443R-4
│
A22Z-3443B-1
START
A22Z-3443B-3
ON
A22Z-3443B-5
OFF
A22Z-3443B-6
UP
A22Z-3443B-7
DOWN
A22Z-3443B-8
POWER ON
A22Z-3443B-9
OFF-ON
A22Z-3443B-10
Standard
size
The Lock Ring is used when more
secure lock feature is required.
Legend
Plates
A22Z-3500-1
ø9~11
A22Z-3500-2
Attached to the Standard
Plate Frame.
Material: Acrylic.
With text
White text
on black
background
Used to prevent dust or water
from entering the Operation Unit
(Pushbutton, etc.).
Color: opaque
Material: silicon
Can be plugged into pre-cut panel
holes for future expansion.
The color is black.
Large
size
Black
A22Z-3453B
Red
A22Z-3453R
White
A22Z-3453W
Transparent
A22Z-3453C
Without
text
Attached to the Large-size
Legend Plate Frame.
Material: Acrylic.
Material: Polycarbonate resin.
No print (Round)
A22Z-B103
ø7~9
Remarks
Black
Without
text
A22Z-3333
A22Z-3330
For flat models
Control Boxes
Classification
Snap-in Legend plate is acrylic.
Without Snap-in Legend Plate
Round
Appearance
A22Z-3320
A22Z-3331
Black
Hole plug
Item
A22Z-3323
White
With Snap-in Legend
Plate (without text)
Lock Ring
Remarks
Snap-in Legend Plate is acrylic.
Black
Legend
Plate
Frames
19
Plastic connector used to extend
a cable from the Switch Box.
(See page 30)
Character Films
Character
Print
(Round)
A22Z-3460
│
A22Z-3460-1
A22Z-3460-2
START
A22Z-3460-3
STOP
A22Z-3460-4
After printing on a film,
affix to the indicator Plate of
the Lighted Pushbotton Switch.
(The back is coated with
adhesive.)
● Tools
Item
Appearance
Part No.
Remarks
Lamp Extractor
A22Z-3901
Rubber tool used to easily replace Lamps.
Tightening wrench
A22Z-3905
Tool used to tighten nuts from the back of the panel.
18
A22R/M22R Series
A22R/M22R Series
Accessories / Tools
Accessories / Tools
Items
IItems
t ems
● Accessories
● Accessories
Item
Standard
size
Appearance
Classification
Part No.
White
A22Z-3321
Red
A22Z-3322
With Snap-in Legend
Plate (without text)
Without Snap-in Legend Plate
Large
size
Red
A22Z-3332
Round
A22Z-3360
A22Z-3600F
Sealing Caps
For projection models
Connectors
A22Z-3600T
A22Z-3530
One hole
A22Z-B101
Two holes
A22Z-B102
Three holes
Applicable
diameter
(mm)
Part No.
A22Z-3443B
Red
A22Z-3443R
White
A22Z-3443W
Transparent
A22Z-3443C
White text
on red
background
A22Z-3443R-2
STOP
A22Z-3443R-4
│
A22Z-3443B-1
START
A22Z-3443B-3
ON
A22Z-3443B-5
OFF
A22Z-3443B-6
UP
A22Z-3443B-7
DOWN
A22Z-3443B-8
POWER ON
A22Z-3443B-9
OFF-ON
A22Z-3443B-10
Standard
size
The Lock Ring is used when more
secure lock feature is required.
Legend
Plates
A22Z-3500-1
ø9~11
A22Z-3500-2
Attached to the Standard
Plate Frame.
Material: Acrylic.
With text
White text
on black
background
Used to prevent dust or water
from entering the Operation Unit
(Pushbutton, etc.).
Color: opaque
Material: silicon
Can be plugged into pre-cut panel
holes for future expansion.
The color is black.
Large
size
Black
A22Z-3453B
Red
A22Z-3453R
White
A22Z-3453W
Transparent
A22Z-3453C
Without
text
Attached to the Large-size
Legend Plate Frame.
Material: Acrylic.
Material: Polycarbonate resin.
No print (Round)
A22Z-B103
ø7~9
Remarks
Black
Without
text
A22Z-3333
A22Z-3330
For flat models
Control Boxes
Classification
Snap-in Legend plate is acrylic.
Without Snap-in Legend Plate
Round
Appearance
A22Z-3320
A22Z-3331
Black
Hole plug
Item
A22Z-3323
White
With Snap-in Legend
Plate (without text)
Lock Ring
Remarks
Snap-in Legend Plate is acrylic.
Black
Legend
Plate
Frames
19
Plastic connector used to extend
a cable from the Switch Box.
(See page 30)
Character Films
Character
Print
(Round)
A22Z-3460
│
A22Z-3460-1
A22Z-3460-2
START
A22Z-3460-3
STOP
A22Z-3460-4
After printing on a film,
affix to the indicator Plate of
the Lighted Pushbotton Switch.
(The back is coated with
adhesive.)
● Tools
Item
Appearance
Part No.
Remarks
Lamp Extractor
A22Z-3901
Rubber tool used to easily replace Lamps.
Tightening wrench
A22Z-3905
Tool used to tighten nuts from the back of the panel.
20
A22R/M22R Series
A22R/M22R Series
Characteristics
Specifications
C haract erist ics
Characteristics
Approve
Approv
e d sstt a n d a r d s
● Environment
● Switch unit
UL 508/CSA C22.2 No.14
File No. E76675
6A 240VAC/10A 120VAC
EN60947-5-1 (low voltage directive) 3A 240VAC (AC-15)
UL, cUL
EN
GB/14048.5-2001
3A 240VAC/1.5A 24VDC
CCC
● Lamp unit
UL 508/CSA C22.2 No.14
File No. E76675
24VAC/DC MAX
UL, cUL
● Voltage-reduction unit
UL 508/CSA C22.2 No.14
File No. E76675
220VAC
GB/14048.5-2001
220VAC
UL, cUL
CCC
Ambient temperature*1
Non-lighted type: -20 to +60ºC
Lighted type: -20 to +50ºC
Ambient humidity
-35 to 85%RH
Storage temperature*1
-40 to +70ºC
Protective code*2
IP65
Vibration resistance
10 to 55Hz, Double amplitude 1.5mm
Shock resistance
Non-lighted type: 1,000m/s2
Lighted type: 600m/s2
*1: With no icing or condensation
*2: Protection against dust or water from the front of a mounting panel side
● Operation
Operation
● Indicator
UL, cUL
UL 508/CSA C22.2 No.14
File No. E76675
12A: 12VAC/DC
24A: 24VAC/DC
T2 : 220VAC
CCC
GB/14048.5-2001
T2 : 220VAC
Operating
frequency
Slow action
Mechanical
Momentary operation: 60 operations/minute max.
Electrical
Knob-type and Key-type selector: 30 operations/minute max.
Mechanical durability
Ratings
Momentary switch :3,000,000 operations
Alternate, Key/Knob Selector switches: 300,000 operations
● Electrical Characteristics (Switch block)
● Contacts
Insulation resistance
100MΩ Minimum (At 500VDC)
Dielectric strength
Between terminals of same polarity: AC2,500V 50/60Hz for 1 minute
Between terminals of different polarity: AC2,500V 50/60Hz for 1 minute
Rated current values are determined according to the testing conditions. The above ratings were obtained by conducting tests under the following
conditions:
Ambient temperature: 20+/- 2ºC
Ambient humidity: 65+/-5%RH
Operating frequency: 30 operations/minute
Rating
AC-15, A600, Ue=240V, Ie=3A
Rated insulation voltage
Ui=600V, Pollution degree: 3
● LED (For pushbutton unit)
Conditional short-circuit current
10A, IEC60209-1
Electrical durability
500,000 operations Minimum (at AC 240V, 3A, cosø=0.4)
Rated current
(A)
10
21
Rated voltage
(V)
240
Inductive load
Power facfor
0.4
Rated current (A)
3
Operating voltage
Current consumption
AC/DC 6V±5%
AC/DC 12V±5%
AC/DC 24V±5%
20mA
20mA
20mA
Operating voltage
Current consumption
AC/DC 12V±5%
20mA
AC/DC 24V±5%
20mA
● LED (For indicator unit)
● Voltage reduction unit (For pushbutton and indicator units)
Operating voltage
Current consumption
AC 200V(190 to 230V)
20mA
20
A22R/M22R Series
A22R/M22R Series
Characteristics
Specifications
C haract erist ics
Characteristics
Approve
Approv
e d sstt a n d a r d s
● Environment
● Switch unit
UL 508/CSA C22.2 No.14
File No. E76675
6A 240VAC/10A 120VAC
EN60947-5-1 (low voltage directive) 3A 240VAC (AC-15)
UL, cUL
EN
GB/14048.5-2001
3A 240VAC/1.5A 24VDC
CCC
● Lamp unit
UL 508/CSA C22.2 No.14
File No. E76675
24VAC/DC MAX
UL, cUL
● Voltage-reduction unit
UL 508/CSA C22.2 No.14
File No. E76675
220VAC
GB/14048.5-2001
220VAC
UL, cUL
CCC
Ambient temperature*1
Non-lighted type: -20 to +60ºC
Lighted type: -20 to +50ºC
Ambient humidity
-35 to 85%RH
Storage temperature*1
-40 to +70ºC
Protective code*2
IP65
Vibration resistance
10 to 55Hz, Double amplitude 1.5mm
Shock resistance
Non-lighted type: 1,000m/s2
Lighted type: 600m/s2
*1: With no icing or condensation
*2: Protection against dust or water from the front of a mounting panel side
● Operation
Operation
● Indicator
UL, cUL
UL 508/CSA C22.2 No.14
File No. E76675
12A: 12VAC/DC
24A: 24VAC/DC
T2 : 220VAC
CCC
GB/14048.5-2001
T2 : 220VAC
Operating
frequency
Slow action
Mechanical
Momentary operation: 60 operations/minute max.
Electrical
Knob-type and Key-type selector: 30 operations/minute max.
Mechanical durability
Ratings
Momentary switch :3,000,000 operations
Alternate, Key/Knob Selector switches: 300,000 operations
● Electrical Characteristics (Switch block)
● Contacts
Insulation resistance
100MΩ Minimum (At 500VDC)
Dielectric strength
Between terminals of same polarity: AC2,500V 50/60Hz for 1 minute
Between terminals of different polarity: AC2,500V 50/60Hz for 1 minute
Rated current values are determined according to the testing conditions. The above ratings were obtained by conducting tests under the following
conditions:
Ambient temperature: 20+/- 2ºC
Ambient humidity: 65+/-5%RH
Operating frequency: 30 operations/minute
Rating
AC-15, A600, Ue=240V, Ie=3A
Rated insulation voltage
Ui=600V, Pollution degree: 3
● LED (For pushbutton unit)
Conditional short-circuit current
10A, IEC60209-1
Electrical durability
500,000 operations Minimum (at AC 240V, 3A, cosø=0.4)
Rated current
(A)
10
21
Rated voltage
(V)
240
Inductive load
Power facfor
0.4
Rated current (A)
3
Operating voltage
Current consumption
AC/DC 6V±5%
AC/DC 12V±5%
AC/DC 24V±5%
20mA
20mA
20mA
Operating voltage
Current consumption
AC/DC 12V±5%
20mA
AC/DC 24V±5%
20mA
● LED (For indicator unit)
● Voltage reduction unit (For pushbutton and indicator units)
Operating voltage
Current consumption
AC 200V(190 to 230V)
20mA
22
A22R/M22R Series
A22R/M22R Series
Characteristics
Operating
Operati
n g cha
c h a r a ct
c t e r i st
s t i cs
cs
Terminal
Terminal Arrangement
● Bottom view (unit: mm)
● Pushbutton switch (1a1b)
Total Travel Force (TTF)
29.4N Maximum
Total Travel (TT)
5.5mm Maximum
No-lighted (1a1b)
19.8
Lighted
Indicator
9.9
10.1
Switch Block
Total Travel (TT)
2-notch: approx. 90 degree (3-notch: approx.45 degree)
M3.5±Screw
Releasing Force (RF)
Switch Blocks
26.2
Manual reset: 0.34N·m Maximum *
Auto-reset
2-notch: 0.25N·m *
3-notch: 0.34N·m *
20.2
● Knob-type selector switch (1a1b)
Total Travel Force (TTF)
Lamp Socket
Manual reset: 0.34N·m Maximum *
* Rotation torque for knob type/key type selector switches.
● Key-type selector switch (1a1b)
Total Travel Force (TTF)
Manual reset: 0.34N·m Maximum *
Auto-reset
2-notch: 0.25N·m *
3-notch: 0.34N·m *
Total Travel (TT)
2-notch: approx. 90 degree (3-notch: approx.45 degree)
Releasing Force (RF)
Manual reset: 0.34N·m Maximum *
23
Terminal connection
connect ion
Type
Terminal connection
BOTTOM VIEW
Non-lighted (1a1b)
1
3
2
4
* Rotation torque for knob type/key type selector switches.
BOTTOM VIEW
1
3
X1
Lighted without voltage
reduction unit (1a1b)
x
2
4
X2
* LED: For AC/DC
BOTTOM VIEW
1
3
X1
Lighted with voltage
reduction unit (1a1b)
x
2
X2
4
22
A22R/M22R Series
A22R/M22R Series
Characteristics
Operating
Operati
n g cha
c h a r a ct
c t e r i st
s t i cs
cs
Terminal
Terminal Arrangement
● Bottom view (unit: mm)
● Pushbutton switch (1a1b)
Total Travel Force (TTF)
29.4N Maximum
Total Travel (TT)
5.5mm Maximum
No-lighted (1a1b)
19.8
Lighted
Indicator
9.9
10.1
Switch Block
Total Travel (TT)
2-notch: approx. 90 degree (3-notch: approx.45 degree)
M3.5±Screw
Releasing Force (RF)
Switch Blocks
26.2
Manual reset: 0.34N·m Maximum *
Auto-reset
2-notch: 0.25N·m *
3-notch: 0.34N·m *
20.2
● Knob-type selector switch (1a1b)
Total Travel Force (TTF)
Lamp Socket
Manual reset: 0.34N·m Maximum *
* Rotation torque for knob type/key type selector switches.
● Key-type selector switch (1a1b)
Total Travel Force (TTF)
Manual reset: 0.34N·m Maximum *
Auto-reset
2-notch: 0.25N·m *
3-notch: 0.34N·m *
Total Travel (TT)
2-notch: approx. 90 degree (3-notch: approx.45 degree)
Releasing Force (RF)
Manual reset: 0.34N·m Maximum *
23
Terminal connection
connect ion
Type
Terminal connection
BOTTOM VIEW
Non-lighted (1a1b)
1
3
2
4
* Rotation torque for knob type/key type selector switches.
BOTTOM VIEW
1
3
X1
Lighted without voltage
reduction unit (1a1b)
x
2
4
X2
* LED: For AC/DC
BOTTOM VIEW
1
3
X1
Lighted with voltage
reduction unit (1a1b)
x
2
X2
4
24
A22R/M22R Series
A22R/M22R Series
Precautions
25
Precautions
Precauti
Prec
aution
ons
Precaut ions
Precautions
Warning
Do not wire and/or touch the switch
terminal while power is supplied to
the switch to avoid electric shock.
Correct Use
● Mounting
• Always make sure that the power is turned OFF before
mounting, removing, or wiring the Switch, or performing
maintenance.
• Do not tighten the mounting ring more than necessary using
tools such as pointed-nose pliers. Doing so will damage the
mounting ring. The tightening torque is 0.98 to 1.96N·m.
• Recommended panel thickness: 1 to 5 mm.
● Wiring
• Terminal screws must be Phillips with a square washer.
• The tightening torque is 1.08 to 1.27N·m.
• Single wires, stranded wires and crimp terminals except round
type can be connected to the Switch.
• Applicable Wire Size
Strand wire: 2mm2 Maximum
Solid wire: 1.6mm diameter Maximum
Bare Crimp Terminals
● Operational Environment
• The IP65 model is designed with a degree of protection so that it will not
sustain damage if it is subject to water from any direction to front of the panel.
• This Switch is indoor use only. Outdoor use of the Switch will cause
operation failure of the Switch.
• Do not use the Switch in the water, oil, or in locations where water, oils,
detergent, chemicals, or solvent is applied to the Switch always.
Otherwise, switching failure will be happened.
• Do not use the Switch under the environmental condition where corrosive
gas (ammonia, chlorine, dioxide sulfur…etc.) is generated. Otherwise,
the Switch will corrode.
• Do not use the Switch in locations where dust, metal or plastic dust exists.
Dust will accumulate o the Switch, and then the Switch wouldn’t operate
normally.
• Do not use the Switch under the environmental condition where excessive
vibration or shock exists. Otherwise, incorrect switching would occur.
● Electrical Conditions
• The switching load capacity of the Switch greatly varies between AC and
DC. Always be sure to apply the rated load. The control capacity will
drastically drop if it is a DC load. This is because a DC load has no current
zero-cross point, unlike an AC load. Therefore, if an arc is generated, it
may continue for a comparatively long time. Furthermore, the current
direction is always the same, which results in a contact relocation
phenomena whereby the contacts easily stick to each other and do not
separate when the surfaces of the contacts are uneven.
• Some types of load have a great difference between normal current and
inrush current. Make sure that the inrush current is within the permissible
value. The greater the inrush current in the closed circuit is, the greater
the contact abrasion or shift will be. Consequently, contact weld, contact
separation failures, or insulation failures may result. Furthermore, the
Switch may be broken or damaged.
• If the load is inductive, counter-electromotive voltage will be generated.
The higher the voltage is, the higher the generated energy will be, which
increase the abrasion of the contacts and contact relocation phenomena.
Be sure to use the Switch within the rated conditions.
I
(A)
8mm max.
Solenoid
(Approximately
10 to 20 times higher)
Incandescent lamp
(Approximately
10 to 15 times higher)
16.0mm max.
i
Crimp Terminal with Insulating Sheath
8mm max.
Relay
(Approximately
4 to 5 times
higher)
20.2mm max.
o
(Steady current)
(Time)
t
• Before using the Switch, be sure to test the Switch under actual conditions.
• This product is a standard load type Switch. Using the Switch for opening
and closing a microload circuit may cause contact failure. Use the Switch
within the operating range as shown in below chart.
Voltage (V)
• Secure appropriate insulation distance after wiring of the Switch.
• Perform wiring so that the lead wires will not be caught on
other objects as this will cause stress on the Switch terminals.
Wire the Switch so that there is slack in the lead wires and fix
lead wires at intermediate points. If the panel to which the
Switch is mounted needs to be opened and closed for
maintenance purpose, perform wiring so that the opening and
closing of the panel will not interfere with the wiring.
0.16mA
1.6mA
100mA
30
24
Microload
area
Standard
load area
12
Invalid
area
5
0
0.1
1mA
10mA
1
10
● Mechanical Conditions
• Do not use the Switch for loads that exceed the rated
switching capacity or other contact ratings. Doing so may
result in contact weld, separation failure, or insulation failures.
Furthermore, the Switch may be broken or damaged.
• Do not touch the charged switch terminals while power is
supplied, otherwise an electric shock may be received.
• The life of the Switch varies greatly with switching conditions.
Before using the Switch, be sure to test the Switch under
actual conditions. Make sure that the number of switching
operations is within the permissible range.
If a deteriorated Switch is used continuously, insulation
failures, contact weld, contact failures, switch damage, or
switch burnout may result.
• Do not apply excessive or incorrect voltages to the Switch or
incorrectly wire the terminals. Otherwise, the Switch may not
function properly and have an adverse effect on external
circuitry.
Furthermore, the Switch itself may become damaged or burnt.
• Do not use the Switch in locations where flammable or
explosive gasses are present. Otherwise switching arcs or
heat radiation may cause a fire or explosion.
• Do not drop or disassemble the Switch, otherwise it may not
be capable of full performance. Furthermore, it may be broken
or burnt.
• Operating the Switch using a hard object (e.g., metal), or with
a large or sudden force, may deform or damage the Switch,
resulting in faulty or rough operation, or shortening of the
Switch life.
100
1,000
Current (mA)
• When use the Switch for opening and closing a microload or large-load,
use the Switch with an appropriate relay.
Hammer
Do not apply excessive
or sudden force.
• The pushbutton surface is composed of resin. Therefore, do
not attempt to operate the pushbutton using a sharp object,
such as a screwdriver or a pair of tweezers. Also, do not
drop, throw, or knock the Switch. Doing so may damage or
deform the pushbutton surface and result in faulty operation.
Do not use sharp objects.
● LED
• The LED current-limiting resistor is built-in, so internal
resistance is not required.
• If commercially available LEDs are used, select the ones that
meet the following conditions:
Base: BA9S/13@
Overall length: 26mm Maximum
Power consumption: 2.6 W Maximum
● Storage
Motor
(Approximately
5 to 10 times
higher)
(Current)
● Switching
• When the Switch is left unused or stored for long periods, the
ambient conditions can have a great effect on the condition of
the Switch. In certain environments, leaving the Switch
exposed may result I deterioration (i.e., oxidation, or the
creation of an oxide film) of the contacts and terminals,
causing the contact resistance to increase, and making it
difficult to solder the lead wires. Therefore, store in a
well-ventilated room, inside, for example, a non-hygroscopic
case, in a location where no corrosive gasses are present.
• If the Switch is stored in a location where it will be exposed to
direct light, colored resin in the colored plate may fade.
Therefore, do not store the Switch I locations where it will be
exposed to direct light.
Screwdriver
Tweezers
• Periodic maintenance is required to use the Switch stably.
24
A22R/M22R Series
A22R/M22R Series
Precautions
25
Precautions
Precauti
Prec
aution
ons
Precaut ions
Precautions
Warning
Do not wire and/or touch the switch
terminal while power is supplied to
the switch to avoid electric shock.
Correct Use
● Mounting
• Always make sure that the power is turned OFF before
mounting, removing, or wiring the Switch, or performing
maintenance.
• Do not tighten the mounting ring more than necessary using
tools such as pointed-nose pliers. Doing so will damage the
mounting ring. The tightening torque is 0.98 to 1.96N·m.
• Recommended panel thickness: 1 to 5 mm.
● Wiring
• Terminal screws must be Phillips with a square washer.
• The tightening torque is 1.08 to 1.27N·m.
• Single wires, stranded wires and crimp terminals except round
type can be connected to the Switch.
• Applicable Wire Size
Strand wire: 2mm2 Maximum
Solid wire: 1.6mm diameter Maximum
Bare Crimp Terminals
● Operational Environment
• The IP65 model is designed with a degree of protection so that it will not
sustain damage if it is subject to water from any direction to front of the panel.
• This Switch is indoor use only. Outdoor use of the Switch will cause
operation failure of the Switch.
• Do not use the Switch in the water, oil, or in locations where water, oils,
detergent, chemicals, or solvent is applied to the Switch always.
Otherwise, switching failure will be happened.
• Do not use the Switch under the environmental condition where corrosive
gas (ammonia, chlorine, dioxide sulfur…etc.) is generated. Otherwise,
the Switch will corrode.
• Do not use the Switch in locations where dust, metal or plastic dust exists.
Dust will accumulate o the Switch, and then the Switch wouldn’t operate
normally.
• Do not use the Switch under the environmental condition where excessive
vibration or shock exists. Otherwise, incorrect switching would occur.
● Electrical Conditions
• The switching load capacity of the Switch greatly varies between AC and
DC. Always be sure to apply the rated load. The control capacity will
drastically drop if it is a DC load. This is because a DC load has no current
zero-cross point, unlike an AC load. Therefore, if an arc is generated, it
may continue for a comparatively long time. Furthermore, the current
direction is always the same, which results in a contact relocation
phenomena whereby the contacts easily stick to each other and do not
separate when the surfaces of the contacts are uneven.
• Some types of load have a great difference between normal current and
inrush current. Make sure that the inrush current is within the permissible
value. The greater the inrush current in the closed circuit is, the greater
the contact abrasion or shift will be. Consequently, contact weld, contact
separation failures, or insulation failures may result. Furthermore, the
Switch may be broken or damaged.
• If the load is inductive, counter-electromotive voltage will be generated.
The higher the voltage is, the higher the generated energy will be, which
increase the abrasion of the contacts and contact relocation phenomena.
Be sure to use the Switch within the rated conditions.
I
(A)
8mm max.
Solenoid
(Approximately
10 to 20 times higher)
Incandescent lamp
(Approximately
10 to 15 times higher)
16.0mm max.
i
Crimp Terminal with Insulating Sheath
8mm max.
Relay
(Approximately
4 to 5 times
higher)
20.2mm max.
o
(Steady current)
(Time)
t
• Before using the Switch, be sure to test the Switch under actual conditions.
• This product is a standard load type Switch. Using the Switch for opening
and closing a microload circuit may cause contact failure. Use the Switch
within the operating range as shown in below chart.
Voltage (V)
• Secure appropriate insulation distance after wiring of the Switch.
• Perform wiring so that the lead wires will not be caught on
other objects as this will cause stress on the Switch terminals.
Wire the Switch so that there is slack in the lead wires and fix
lead wires at intermediate points. If the panel to which the
Switch is mounted needs to be opened and closed for
maintenance purpose, perform wiring so that the opening and
closing of the panel will not interfere with the wiring.
0.16mA
1.6mA
100mA
30
24
Microload
area
Standard
load area
12
Invalid
area
5
0
0.1
1mA
10mA
1
10
● Mechanical Conditions
• Do not use the Switch for loads that exceed the rated
switching capacity or other contact ratings. Doing so may
result in contact weld, separation failure, or insulation failures.
Furthermore, the Switch may be broken or damaged.
• Do not touch the charged switch terminals while power is
supplied, otherwise an electric shock may be received.
• The life of the Switch varies greatly with switching conditions.
Before using the Switch, be sure to test the Switch under
actual conditions. Make sure that the number of switching
operations is within the permissible range.
If a deteriorated Switch is used continuously, insulation
failures, contact weld, contact failures, switch damage, or
switch burnout may result.
• Do not apply excessive or incorrect voltages to the Switch or
incorrectly wire the terminals. Otherwise, the Switch may not
function properly and have an adverse effect on external
circuitry.
Furthermore, the Switch itself may become damaged or burnt.
• Do not use the Switch in locations where flammable or
explosive gasses are present. Otherwise switching arcs or
heat radiation may cause a fire or explosion.
• Do not drop or disassemble the Switch, otherwise it may not
be capable of full performance. Furthermore, it may be broken
or burnt.
• Operating the Switch using a hard object (e.g., metal), or with
a large or sudden force, may deform or damage the Switch,
resulting in faulty or rough operation, or shortening of the
Switch life.
100
1,000
Current (mA)
• When use the Switch for opening and closing a microload or large-load,
use the Switch with an appropriate relay.
Hammer
Do not apply excessive
or sudden force.
• The pushbutton surface is composed of resin. Therefore, do
not attempt to operate the pushbutton using a sharp object,
such as a screwdriver or a pair of tweezers. Also, do not
drop, throw, or knock the Switch. Doing so may damage or
deform the pushbutton surface and result in faulty operation.
Do not use sharp objects.
● LED
• The LED current-limiting resistor is built-in, so internal
resistance is not required.
• If commercially available LEDs are used, select the ones that
meet the following conditions:
Base: BA9S/13@
Overall length: 26mm Maximum
Power consumption: 2.6 W Maximum
● Storage
Motor
(Approximately
5 to 10 times
higher)
(Current)
● Switching
• When the Switch is left unused or stored for long periods, the
ambient conditions can have a great effect on the condition of
the Switch. In certain environments, leaving the Switch
exposed may result I deterioration (i.e., oxidation, or the
creation of an oxide film) of the contacts and terminals,
causing the contact resistance to increase, and making it
difficult to solder the lead wires. Therefore, store in a
well-ventilated room, inside, for example, a non-hygroscopic
case, in a location where no corrosive gasses are present.
• If the Switch is stored in a location where it will be exposed to
direct light, colored resin in the colored plate may fade.
Therefore, do not store the Switch I locations where it will be
exposed to direct light.
Screwdriver
Tweezers
• Periodic maintenance is required to use the Switch stably.
A22R/M22R Series
A22R/M22R Series
Installation
Installation
Mounting
Mounti
ng t o t h e P an
anel
➀ Panel Hole Dimensions
• The cutout dimensions are as shown in below:
When Lock Ring
is not used.
When Lock Ring
is used.
• Recommended panel thickness is 1 to 5mm.
• In outer surface treatment such as coating is performed for
the panel, the panel dimensions after outer surface treatment
must meet the specified panel dimensions.
➁ Matrix Installation
(1) The following panel hole (2)
dimensions apply when
Switch Unit and the
Standard-size Legend
Plate Frame and Lock
Ring are mounted, and
lead wires are connected
directly to the Switch Block.
The following panel hole
dimensions apply when the
Large-size Legend Plate
Frame is mounted, and
when crimp terminals are
connected to the Switch
Block terminals.
How
H
ow to
t o confirm
conf irm the
t he Lever Position,
Posit ion, OPEN or LOC K
➂ Mounting the Operation Unit on the Panel
• Insert the Operation Unit (Pushbutton, etc.) from the front
surface of the panel, insert the Lock Ring and the mounting
nut from the terminal side, then tighten the nut. Before
tightening, check that the rubber washer is present between
the Pushbutton Unit and the panel.
• When using a Legend Plate Frame, put one rubber washer
each between the Legend Plate Frame and the panel and
between the Operation Unit and the Legend Plate Frame.
(One rubber washer will be provided when one Legend Plate
Frame is ordered.)
• Align the Lock Ring with the groove in the casing, then insert
the Lock Ring so that its edge is located on the panel side.
• Tighten the mounting nut at a torque of 0.98 to 1.96N·m.
• When using a Lock Ring, replace with the supplied Lock Ring,
insert the projecting part into the lock slot, and then tighten the
mounting nut.
Hold here
Rubber washer
Mounting nut
● The Lever Position, OPEN (Operation unit is not fixed)/LOCK (Operation unit is fixed), can be confirmed from the Switch
terminal side.
Left side
Right side
In case that no switch block
is mounted on the mounting
plate No.1.
Two
holes
One
hole
Panel
(OPEN condition)
Panel Projection
part
(LOCK condition)
Lock Ring
Panel
➃ Mounting the Switch on the Pushbutton Unit
• Insert the Pushbutton Unit into the Switch Unit, aligning the
arrow mark inscribed on the Case with the lever on the Switch
Blocks, then move the lever in the direction indicated by the
arrow in the following figure.
In case that a switch block
is mounted on the mounting
plate No.1.
Left side
Right side
Two
holes
Hole is
not shown
Operation Unit
45 min.
Arrow mark
(OPEN condition)
Lever
Type of crimp terminal
Dimension A
Bare crimp terminals
51 mm Minimum
Crimp terminals with insulating sheath 60 mm Minimum
Note: The above dimensions are the minimum dimensions for
when the wires described under “Applicable Wire Size”.
If a different wires are used, the wiring dimensions may
be different so determine an appropriate pitch before
setup.
➄ Removing the Switch
• Move the lever in the direction indicated by the arrow in the
following figure, then pull the Pushbutton Unit or the Switch
Blocks.
• Since the lever has a hole with an inside diameter of 6.5mm,
the lever can be moved in the specified direction by inserting
a screwdriver into the hole and then moving the screwdriver.
Screwdriver
In case that a switch block
is mounted on the mounting
plate No.1 and an indicator
unit is mounted on the
mounting plate No.2.
Left side
(LOCK condition)
Right side
One
hole
Hole is
not shown
(OPEN condition)
(LOCK condition)
A22R/M22R Series
A22R/M22R Series
Installation
Installation
Mounting
Mounti
ng t o t h e P an
anel
➀ Panel Hole Dimensions
• The cutout dimensions are as shown in below:
When Lock Ring
is not used.
When Lock Ring
is used.
• Recommended panel thickness is 1 to 5mm.
• In outer surface treatment such as coating is performed for
the panel, the panel dimensions after outer surface treatment
must meet the specified panel dimensions.
➁ Matrix Installation
(1) The following panel hole (2)
dimensions apply when
Switch Unit and the
Standard-size Legend
Plate Frame and Lock
Ring are mounted, and
lead wires are connected
directly to the Switch Block.
The following panel hole
dimensions apply when the
Large-size Legend Plate
Frame is mounted, and
when crimp terminals are
connected to the Switch
Block terminals.
How
H
ow to
t o confirm
conf irm the
t he Lever Position,
Posit ion, OPEN or LOC K
➂ Mounting the Operation Unit on the Panel
• Insert the Operation Unit (Pushbutton, etc.) from the front
surface of the panel, insert the Lock Ring and the mounting
nut from the terminal side, then tighten the nut. Before
tightening, check that the rubber washer is present between
the Pushbutton Unit and the panel.
• When using a Legend Plate Frame, put one rubber washer
each between the Legend Plate Frame and the panel and
between the Operation Unit and the Legend Plate Frame.
(One rubber washer will be provided when one Legend Plate
Frame is ordered.)
• Align the Lock Ring with the groove in the casing, then insert
the Lock Ring so that its edge is located on the panel side.
• Tighten the mounting nut at a torque of 0.98 to 1.96N·m.
• When using a Lock Ring, replace with the supplied Lock Ring,
insert the projecting part into the lock slot, and then tighten the
mounting nut.
Hold here
Rubber washer
Mounting nut
● The Lever Position, OPEN (Operation unit is not fixed)/LOCK (Operation unit is fixed), can be confirmed from the Switch
terminal side.
Left side
Right side
In case that no switch block
is mounted on the mounting
plate No.1.
Two
holes
One
hole
Panel
(OPEN condition)
Panel Projection
part
(LOCK condition)
Lock Ring
Panel
➃ Mounting the Switch on the Pushbutton Unit
• Insert the Pushbutton Unit into the Switch Unit, aligning the
arrow mark inscribed on the Case with the lever on the Switch
Blocks, then move the lever in the direction indicated by the
arrow in the following figure.
In case that a switch block
is mounted on the mounting
plate No.1.
Left side
Right side
Two
holes
Hole is
not shown
Operation Unit
45 min.
Arrow mark
(OPEN condition)
Lever
Type of crimp terminal
Dimension A
Bare crimp terminals
51 mm Minimum
Crimp terminals with insulating sheath 60 mm Minimum
Note: The above dimensions are the minimum dimensions for
when the wires described under “Applicable Wire Size”.
If a different wires are used, the wiring dimensions may
be different so determine an appropriate pitch before
setup.
➄ Removing the Switch
• Move the lever in the direction indicated by the arrow in the
following figure, then pull the Pushbutton Unit or the Switch
Blocks.
• Since the lever has a hole with an inside diameter of 6.5mm,
the lever can be moved in the specified direction by inserting
a screwdriver into the hole and then moving the screwdriver.
Screwdriver
In case that a switch block
is mounted on the mounting
plate No.1 and an indicator
unit is mounted on the
mounting plate No.2.
Left side
(LOCK condition)
Right side
One
hole
Hole is
not shown
(OPEN condition)
(LOCK condition)
28
29
A22R/M22R Series
A22R/M22R Series
Installation
Installation
Mounting
e p l aci
a c i ng
n g t h e Co
Color
Cap
Mounti
ng / R ep
lo r Ca
p
Mounting/Replacing
Mount
ing/ R eplacing the
t he Switch
Sw it ch Unit
U nit and Indicator
I ndicat or Unit
➀ Installing the Switch Blocks
Projection type
➁ Removing the Switch Base
• Mount the Unit according to the indicate numbers on the
Mounting Plate.
• Grip and rotate the Color Cap with your fingers.
No. on the
Mounting Plate
• Insert a screwdriver between the Mounting Latch and the
Switch Block, then push down the screwdriver in the direction
indicated by the arrow in the following figure.
Flat-head
screwdriver
Switch Unit
(A22R-10/A22R-01)
Assembl
As
s embl i n g t h e C a
ap
p
➀ Projection type Lighted Pushbutton Switch
• Mount the Color Cap so that the protrusions inside the cap fit
into the grooves in the Pushbutton Unit.
Indicator Unit
(A22R-TN/A22R-T2)
➁ Indicator
• Mount the Color Cap so that the protrusions inside the
Pushbutton Unit fit into the grooves in the cap.
Protrusion part
Protrusion parts
on the Cap
• Hook the small protrusion on
the Switch Block into the groove
on the Mounting Latch on the
other side of the lever, then
push up the Switch Block in the
direction indicated by the arrow
in the figure below:
• One more Switch Block can
be mounted.
Grooves
Reflector
Mounting
Latch
Lever
Color Cap
Color Cap
Switch Block
Installin
e p l aci
a c i ng
ng the L
LED
Ins
tallin g / R ep
ED
➀ Installing/Replacing from the Panel Surface
• Insert the Lamp Extractor(A22Z-3901) into the lamp, then rotate
the Extractor while pressing it.
Protrusion
Protrusion
➁ Installing/Replacing on the Switch
• Grip the lamp with your fingers, then rotate the lamp while
pressing it against the Switch.
Switch Block
Note: In case that two Switch Block
are mounted, a Control Box
cannot be used.
3mm Maximum
Use the following screwdrivers.
28
29
A22R/M22R Series
A22R/M22R Series
Installation
Installation
Mounting
e p l aci
a c i ng
n g t h e Co
Color
Cap
Mounti
ng / R ep
lo r Ca
p
Mounting/Replacing
Mount
ing/ R eplacing the
t he Switch
Sw it ch Unit
U nit and Indicator
I ndicat or Unit
➀ Installing the Switch Blocks
Projection type
➁ Removing the Switch Base
• Mount the Unit according to the indicate numbers on the
Mounting Plate.
• Grip and rotate the Color Cap with your fingers.
No. on the
Mounting Plate
• Insert a screwdriver between the Mounting Latch and the
Switch Block, then push down the screwdriver in the direction
indicated by the arrow in the following figure.
Flat-head
screwdriver
Switch Unit
(A22R-10/A22R-01)
Assembl
As
s embl i n g t h e C a
ap
p
➀ Projection type Lighted Pushbutton Switch
• Mount the Color Cap so that the protrusions inside the cap fit
into the grooves in the Pushbutton Unit.
Indicator Unit
(A22R-TN/A22R-T2)
➁ Indicator
• Mount the Color Cap so that the protrusions inside the
Pushbutton Unit fit into the grooves in the cap.
Protrusion part
Protrusion parts
on the Cap
• Hook the small protrusion on
the Switch Block into the groove
on the Mounting Latch on the
other side of the lever, then
push up the Switch Block in the
direction indicated by the arrow
in the figure below:
• One more Switch Block can
be mounted.
Grooves
Reflector
Mounting
Latch
Lever
Color Cap
Color Cap
Switch Block
Installin
e p l aci
a c i ng
ng the L
LED
Ins
tallin g / R ep
ED
➀ Installing/Replacing from the Panel Surface
• Insert the Lamp Extractor(A22Z-3901) into the lamp, then rotate
the Extractor while pressing it.
Protrusion
Protrusion
➁ Installing/Replacing on the Switch
• Grip the lamp with your fingers, then rotate the lamp while
pressing it against the Switch.
Switch Block
Note: In case that two Switch Block
are mounted, a Control Box
cannot be used.
3mm Maximum
Use the following screwdrivers.
30
31
A22R/M22R Series
A22R/M22R Series
Installation
Installation
Control B ox
ox
Engraving
➀ Mounting the Switch
➁ Creating a Cable Port Hole
The Standard-size Legend Plate Frame can be mounted.
Mount the Switch in the same way as for an ordinary panel.
Snap-in Legend Plate
Place the tip of a screwdriver on the surface where the cable
port hole is to be created with the cover attached and strike the
screwdriver to punch a hole. Attempts to punch a hole on the
other side of the case will damage the Box.
Mounting and Dismounting Snap-in Legend
• Engrave the characters on the surface on the Cap. Make sure that
the characters are aligned parallel to the imaginary lie connecting
the two protruding portions to the left and right of the Cap.
• The characters must not be engraved deeper than 0.5mm. Apply an
alcohol-based paint coating, such as melamine, alkyd, or acrylic
resin paint coating, to the engraved characters.
• Press and secure the Snap-in Legend Plate onto the Legend Plate
Frame.
• The direction of the characters will vary with the mounting direction
of the control panel if the Switch is a knob or key selector model.
Legend Plate Frame
Protruding portions of the Cap
Screwdriver
Side
Snap-in Legend Plate
Cover
Switch box
Concave surface
Cable port hole
Strike the
screwdriver to
punch a hole
by place 4 parts
diagonally.
Groove
Material: Acrylic
➂ Securing the Connector Cable
➀ Insert the connector into the cable port in the Box and secure with the fixing nut inside the box.
➁ Open a hole in the thin rubber section of the rubber ring.
➂ Pass the tightening cap through the cable, insert the cable into the connector, and tighten the hexagonal nut to secure the cable.
Fixing nut
Rubber washer
Connector
Cable diameter (mm)
Connector
7 to 9 mm dia.
A22Z-3500-1
Tightening cap
Cable
9 to 11 mm dia.
A22Z-3500-2
• Engrave the characters directly on the matted side of the Snap-in
Legend Plate.
• The characters must be engraved no deeper than 0.5mm.
• Apply alcohol-based paint coating to the engraved characters.
• If the Snap-in Legend Plate is transparent, engrave the mirror-written
characters on the back of the Snap-in Legend Plate and apply paint
coating of a different color to the remaining part of the Snap-in
Legend Plate.
• To easily remove the Snap-in Legend Plate from the Legend Plate
Frame mounted to the panel. Insert a Tool with a thin tip into the
space between the Snap-in Legend Plate and the Legend Plate
Frame.
Affixing Character Film
• Hold the Cap, remove the cardboard o the Film, and attach the Film
to the Cap. Make sure that the protruding portions of the Cap engage
the cutout portions of the Film and that the characters are aligned
parallel to the imaginary line connecting the two protruding portions
to the left and right of the Cap.
• The Snap-in Legend Plate is easily removed by pressing the
Snap-I Legend Plate from the back of the Legend Plate Frame.
• The Legend Plate Frame is made of acrylic resin, which is easily
damaged by shock. Be sure to handle the Legend Plate Frame
with care.
Remove the cardboard.
Inside
Outside
Box
Protruding portions on Cap
Precautions
ions w
when
Precaut
hen use tthe
he IIndicators
ndicat ors
• Lock Ring (A22Z-3360) cannot be used.
• When use the Legend Plate Frames
(A22Z-332@, A22Z-333@) cut the projection
portions shown in the below fig.
• When use the Control Box (A22Z-B10@), cut the
projection portions shown in the below fig.
Cut the projection portions
Cut the projection portions
30
31
A22R/M22R Series
A22R/M22R Series
Installation
Installation
Control B ox
ox
Engraving
➀ Mounting the Switch
➁ Creating a Cable Port Hole
The Standard-size Legend Plate Frame can be mounted.
Mount the Switch in the same way as for an ordinary panel.
Snap-in Legend Plate
Place the tip of a screwdriver on the surface where the cable
port hole is to be created with the cover attached and strike the
screwdriver to punch a hole. Attempts to punch a hole on the
other side of the case will damage the Box.
Mounting and Dismounting Snap-in Legend
• Engrave the characters on the surface on the Cap. Make sure that
the characters are aligned parallel to the imaginary lie connecting
the two protruding portions to the left and right of the Cap.
• The characters must not be engraved deeper than 0.5mm. Apply an
alcohol-based paint coating, such as melamine, alkyd, or acrylic
resin paint coating, to the engraved characters.
• Press and secure the Snap-in Legend Plate onto the Legend Plate
Frame.
• The direction of the characters will vary with the mounting direction
of the control panel if the Switch is a knob or key selector model.
Legend Plate Frame
Protruding portions of the Cap
Screwdriver
Side
Snap-in Legend Plate
Cover
Switch box
Concave surface
Cable port hole
Strike the
screwdriver to
punch a hole
by place 4 parts
diagonally.
Groove
Material: Acrylic
➂ Securing the Connector Cable
➀ Insert the connector into the cable port in the Box and secure with the fixing nut inside the box.
➁ Open a hole in the thin rubber section of the rubber ring.
➂ Pass the tightening cap through the cable, insert the cable into the connector, and tighten the hexagonal nut to secure the cable.
Fixing nut
Rubber washer
Connector
Cable diameter (mm)
Connector
7 to 9 mm dia.
A22Z-3500-1
Tightening cap
Cable
9 to 11 mm dia.
A22Z-3500-2
• Engrave the characters directly on the matted side of the Snap-in
Legend Plate.
• The characters must be engraved no deeper than 0.5mm.
• Apply alcohol-based paint coating to the engraved characters.
• If the Snap-in Legend Plate is transparent, engrave the mirror-written
characters on the back of the Snap-in Legend Plate and apply paint
coating of a different color to the remaining part of the Snap-in
Legend Plate.
• To easily remove the Snap-in Legend Plate from the Legend Plate
Frame mounted to the panel. Insert a Tool with a thin tip into the
space between the Snap-in Legend Plate and the Legend Plate
Frame.
Affixing Character Film
• Hold the Cap, remove the cardboard o the Film, and attach the Film
to the Cap. Make sure that the protruding portions of the Cap engage
the cutout portions of the Film and that the characters are aligned
parallel to the imaginary line connecting the two protruding portions
to the left and right of the Cap.
• The Snap-in Legend Plate is easily removed by pressing the
Snap-I Legend Plate from the back of the Legend Plate Frame.
• The Legend Plate Frame is made of acrylic resin, which is easily
damaged by shock. Be sure to handle the Legend Plate Frame
with care.
Remove the cardboard.
Inside
Outside
Box
Protruding portions on Cap
Precautions
ions w
when
Precaut
hen use tthe
he IIndicators
ndicat ors
• Lock Ring (A22Z-3360) cannot be used.
• When use the Legend Plate Frames
(A22Z-332@, A22Z-333@) cut the projection
portions shown in the below fig.
• When use the Control Box (A22Z-B10@), cut the
projection portions shown in the below fig.
Cut the projection portions
Cut the projection portions
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change without notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the importation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security interest in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original transportation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
14.
15.
16.
17.
18.
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for published information.
Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or settle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
Property; Confidentiality. Any intellectual property in the Products is the exclusive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law principles). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability. If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Companies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this Product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
2.
3.
4.
5.
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
OMRON INDUSTRIAL AUTOMATION • THE AMERICAS HEADQUARTERS • Schaumburg, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.55.59.01.43.00 • 001.800.556.6766 • mela@omron.com
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 001.800.556.6766 • mela@omron.com
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON EUROpE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • Tel: +31 (0) 23 568 13 00 • Fax: +31 (0) 23 568 13 88 • www.industrial.omron.eu
Automation Systems
• Programmable logic controllers (PLC) • Human machine interfaces (HMI) • Remote I/O
• Industrial PC’s • Software
Authorized Distributor:
Motion & Drives
• Motion controllers • Servo systems • AC drives
Control Components
• Temperature controllers • Power supplies • Timers • Counters • Programmable relays
• Digital panel indicators • Electromechanical relays • Monitoring products • Solid-state relays
• Limit switches • Pushbutton switches • Low voltage switch gear
Sensing & Safety
• Photoelectric sensors • Inductive sensors • Capacitive & pressure sensors
• Cable connectors • Displacement & width-measuring sensors • Vision systems
• Safety networks • Safety sensors • Safety units/relay units • Safety door/guard lock switches
Cat. No. A190-E1-01
10/09
Note: Specifications are subject to change.
Printed on recycled paper.
© 2011 Omron Electronics LLC
Printed in U.S.A.
工商网监
湘ICP备2023018690号
