A6S-6102-P

OMRON ELECTRONICS See full Datasheet below... BUY NOW BUY NOW masterelectronics.com & onlinecomponents.com are authorized e-commerce distributors of electronic components. DIP Switch (Slide Type) A6T/A6S Low-cost DIP Switch with Slide Pins ■ Designed to DIP (Dual Inline Package) standards and allows automatic mounting with IC insertion machines. ■ Washable models with seal tape available. ■ SMT (surface-mounted terminal) models available with embossed taping specifications (units of 900). ■ Gold-plated twin contacts and a slide-type, self- cleaning mechanism ensure high reliability. Ordering Information Type (striker color) No. of poles Standard Flat actuator (Yellow) With seal tape Raised actuator (Yellow) DIP terminal DIP terminal DIP terminal Quantity per stick Standard Flat actuator (Yellow) With seal tape Raised actuator (Yellow) (See note 2.) SMT terminal SMT terminal SMT terminal Type (striker color) No. of poles Quantity per stick Per stick Per embossed tape (units of 900) (See note 1.) 1 130 A6T-1101 A6T-1102 A6T-1104 1 --- --- --- --- --- 2 76 A6T-2101 A6T-2102 A6T-2104 2 76 A6S-2101 A6S2102 --- A6S-2104 3 55 A6T-3101 A6T-3102 A6T-3104 3 55 A6S-3101 A6S3102 --- A6S-3104 4 42 A6T-4101 A6T-4102 A6T-4104 4 42 A6S-4101 A6S4102 A6S-4102-P A6S-4104 5 35 A6T-5101 A6T-5102 A6T-5104 5 35 A6S-5101 A6S5102 --- 6 28 A6T-6101 A6T-6102 A6T-6104 6 28 A6S-6101 A6S6102 A6S-6102-P A6S-6104 7 25 A6T-7101 A6T-7102 A6T-7104 7 25 A6S-7101 A6S7102 --- 8 22 A6T-8101 A6T-8102 A6T-8104 8 22 A6S-8101 A6S8102 A6S-8102-P A6S-8104 9 20 A6T-9101 A6T-9102 A6T-9104 9 20 A6S-9101 A6S9102 --- 10 18 A6T-0101 A6T-0102 A6T-0104 10 18 A6S-0101 A6S0102 A6S-0102-P A6S-0104 Note: A6S-5105 A6S-7104 A6S-9104 1. Switches are packaged in units of 900. Orders must be made in multiples of 900. Switches are not sold individually. 2. Raised actuators on embossed tape must be requested separately because orders can vary by such factors as units per order. 9 A6T/A6S A6T/A6S Specifications ■ Ratings/Characteristics Switching capacity 25 mA at 24 VDC 10 m A (minimum current) at 3.5 VDC Ambient temperature Operating: –20°C to 70°C (with no icing) Ambient humidity Operating: 35% to 90% Insulation resistance 100 MW min. (at 250 VDC) Contact resistance 200 mW max. (initial value) Dielectric strength 500 VAC for 1 min between terminals of the same polarity, and between terminals of different polarity Vibration resistance Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Shock resistance Malfunction: 300 m/s2 min. Life expectancy Mechanical: 1,000 operations min. Electrical: 1,000 operations min. Operating force Flat/raised type 0.29 N min. {30 gf} Weight A6T: 0.26 g (2 poles), 0.44 g (4 poles), 0.62 g (6 poles), 0.79 g (8 poles), 0.96 g (10 poles) A6S: 0.25 g (2 poles), 0.41 g (4 poles), 0.58 g (6 poles), 0.73 g (8 poles), 0.87 g (10 poles) Dimensions Note: 1. All units are in millimeters unless otherwise indicated. 2. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Flat Actuator with DIP Terminal Standard/With Seal Tape A6T-@101 A6T-@102 Note: Terminal length decreased from 4.3 mm to 3.5 mm as of May 2003. Flat Actuator Standard With Seal Tape Raised Actuator Seal tape (t = 0.06) (See note.) Raised Actuator with DIP Terminal A6T-@104 PCB Dimensions (Top View) No. of poles 1.0±0.05 dia. P: pole numbers 10 Model Dimension A 1 A6T-1101 A6T-1102 A6T-1104 3.48 2 A6T-2101 A6T-2102 A6T-2104 6.02 3 A6T-3101 A6T-3102 A6T-3104 8.56 4 A6T-4101 A6T-4102 A6T-4104 11.10 5 A6T-5101 A6T-5102 A6T-5104 13.64 6 A6T-6101 A6T-6102 A6T-6104 16.18 7 A6T-7101 A6T-7102 A6T-7104 18.72 8 A6T-8101 A6T-8102 A6T-8104 21.26 9 A6T-9101 A6T-9102 A6T-9104 23.80 10 A6T-0101 A6T-0102 A6T-0104 26.34 A6T/A6S A6T/A6S Flat Actuator with SMT Terminal Standard/With Seal Tape A6S-@101 A6S-@102 Flat Actuator Standard With Seal Tape Raised Actuator Seal tape (t = 0.06) 0.7 min. Raised Actuator with SMT Terminal No. of poles PCB Dimensions (Top View) A6S-@104 P: pole numbers Model Dimension A 2 A6S-2101 A6S-2102 A6S-2104 6.02 3 A6S-3101 A6S-3102 A6S-3104 8.56 4 A6S-4101 A6S-4102 A6S-4104 11.10 5 A6S-5101 A6S-5102 A6S-5104 13.64 6 A6S-6101 A6S-6102 A6S-6104 16.18 7 A6S-7101 A6S-7102 A6S-7104 18.72 8 A6S-8101 A6S-8102 A6S-8104 21.26 9 A6S-9101 A6S-9102 A6S-9104 23.80 10 A6S-0101 A6S-0102 A6S-0104 26.34 Installation ■ Internal Connections (Top View) ON 1 2 9 10 Precautions Be sure to refer to General Precautions on pages 4 to 6 for details on proper use. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. A102-E1-02 11 Precautions Precautions Safety Precautions ■ Cautions Use the DIP Switch within the rated voltage and current ranges, otherwise the DIP Switch may have a shortened life expectancy, radiate heat, or burn out. This particularly applies to the instantaneous voltages and currents when switching. ■ Correct Use Circuit Design 2. Automatic Soldering Bath (Except A6S-H/A6H) Soldering temperature: 260°C max. Soldering time: 5 s max. for a 1.6-mm thick, single-side PCB Do not use an automatic soldering bath or manual soldering for A6S-H or A6H models. Confirm in advance that flux will not bubble up onto the side of the PCB to which the Switch is mounted. Depending on the type of Switch, the flux may have an adverse effect if it enters the Switch. Although the minimum current is 10 µA (3.5 VDC), contact reliability may need to be improved in some cases. This is particularly true when switching causes an increase in instantaneous current, such as in C-MOS IC applications. Do not let the peak current exceed the rated value here or any other time. Only BCD/hexadecimal 1-2-4-8 code is available for A6C/A6CV/ A6R/A6RV models. If BCD/hexadecimal 1-2-4-8 complement code is required, make the appropriate provisions in the circuit. Mounting Normally the default striker setting is OFF for slide-type DIP Switches and the default rotor setting is 0 for Rotary DIP Switches. Do not change these settings when mounting, soldering, washing or drying Switches. In rare cases, the striker may be deformed by heat generated during soldering. PCB surface Flux surface The A6S-H and A6H are designed specifically for reflow soldering. Do not use an automatic soldering bath or manual soldering for these models. 3. Reflow Soldering Observe the following conditions for reflow soldering the A6S-H and A6H models. (Measurement location: Top of Switch) A6S-H Soldering Conditions Temperature (°C) 1. Automatic Insertion Machine Use a body stopper system for the chute stopper of automatic insertion machines. When mounting Switches using an insertion machine incorporating a half-lead stopper, make sure the machine will not deform the terminals of the Switch, or improper insertion may result. Check actual mounting conditions prior to using a half-lead stopper system. A printed circuit board that is 1.2 to 1.6 mm thick is recommended. Holes on the PCB should be at least 0.9 mm in diameter for automatic insertion. 2. Manual or IC Socket Insertion 260 max. 230 180 150 60 to 120 150 Observe the following conditions when soldering the DIP Switch. 1. General Precautions for Soldering Make sure that the striker of slide-type DIP Switches is set fully to either ON or OFF. (For A6E and A6ER models, however, set the Switch to OFF before soldering.) Make sure that Rotary DIP Switches are correctly set to 0. Misalignment may result in reduced sensitivity due to the soldering heat. Before soldering the Switch on a PCB, make sure there is no unnecessary space between the Switch and the PCB. 40 max. Time (s) 250 max. Terminal pitch, dimensions and other features are identical to that of standard ICs for IC socket compatibility (except for the A6S-H and A6H). Soldering Time (s) Temperature (°C) 230 180 Do not try to remove a Switch by inserting a screwdriver between it and the PCB, and then twisting the screwdriver to peel the Switch off. Use a commercially available inserter/remover to remove the Switch. 60 max. A6H Soldering Conditions Commercially available insertion tools are recommended for mounting ICs on PCBs. Align the terminals so they slide in simultaneously when the Switch is inserted into socket holes or into mounting holes predrilled at the specified dimensions. Apply downward force on the Switch until the terminals are properly seated on the PCB. Preheating Preheating 60 to 120 Do not use reflow soldering for any models other than the A6S-H and A6H. Otherwise the plastic case may melt or deform. The soldering conditions and the temperature around the Switch may vary with the type of reflow bath. Check the temperature profile and confirm soldering conditions as well as the amount of heat applied to the Switch prior to soldering. 4. Manual Soldering (Except A6S-H/A6H) Soldering temperature: 350°C at the tip of the soldering iron. Soldering time: 3 s max. for a 1.6-mm thick, single-side PCB Do not solder the Switch more than twice including any rectification soldering. An interval of five minutes is required between the first and second soldering. 5. Using Flux Making mistakes in the type of flux or in the amount or method in which it is applied can cause flux to enter the interior of the Switch, with adverse effects on Switch performance. Assess the proper flux, conditions, and methods prior to using it. Before soldering the Switch on a multilayer PCB, conduct a test to make sure the Switch will not be deformed by soldering heat on the pattern or land of the multilayer PCB. 4 Precautions Precautions Washing 1. Washable and Non-washable Models The models for which washing are possible are shown in the following table. Washable A6A, A6C, A6CV, A6D, A6DR, A6T (with seal tape), A6S-H (with seal tape), A6H (with seal tape) Non-washable A6R, A6RV, A6T (standard/raised actuator), A6SH (standard/raised actuator), A6E, A6ER 2. Washing Procedure Ultrasonic cleaning is not available for slide-type DIP Switches with seal tape. These models may be wiped or dipped into washing agents for one minute maximum. Slide-type DIP Switches with seal tape can be washed as long as the seal tape is not removed or pasted before washing. Non-compliance here will cause the quality of the seal to decline. 3. Washing Agents Apply alcohol-based solvents to clean washable models. Do not apply water or any other agents to clean any washable models, as such agents may degrade the materials or performance of the Switch. 4. Washing Precautions Do not impose any external force on washable models while washing. Do not clean washable models immediately after soldering. The cleaning agent may be absorbed into the incomplete seal through respiration as the Switch cools. Wait for at least three minutes after soldering before cleaning. Do not use washable Switches submerged in water or in locations exposed to water. Washing equipment incorporating more than one washing bath can be used to clean washable models, provided that the washable models are cleaned for one minute maximum per bath and the total cleaning time does not exceed three minutes. Handling 1. Slide-type DIP Switch operation Do not apply excessive operating force to the Switch. Otherwise the Switch may be damaged or deformed, and the switch mechanism may malfunction as a result. Apply an operating force not exceeding 9.8 N. (Operate each pole separately.) Apply the operating load from the side of the striker. Do not apply a load from an angle or from above the striker. Doing so may deform the Switch contact. Incorrect Correct Set slide-type DIP Switches with a tiny, rounded object, such as the tip of a ball-point pen or a small screwdriver. Do not set the DIP Switch using tweezers or any other sharp object that may damage it. Do not set the DIP Switch using the point of a mechanical pencil, or lead powder or fragments may fall into the Switch and internal circuit board, causing the DIP Switch to malfunction and reducing the dielectric strength of the circuit board. Although raised-type and piano-type strikers can be operated by fingertip, do not push too hard or too fast because this will deform or damage the striker. When setting or operating the A6H, use narrow-headed tweezers or similar implement (without a sharp end), to enable smooth, horizontal operation. Pushing the striker at an angle, or applying excessive load from above may damage or deform the striker and thereby prevent operation. 2. Rotary DIP Switch Operation Set rotary-type DIP Switches with a flat-blade screwdriver that fits into the screwdriver groove. Using a screwdriver of inappropriate dimensions, or using a tool other than a flat-blade screwdriver may cause damage to the groove that may make the Switch impossible to operate. Insert the flat-blade screwdriver vertically to operate the Switch. The Switch may be damaged if the screwdriver is inserted at an angle. Do not use excessive force to operate the Switch, or it may damage or deform the Switch. 3. Setting Set the Switch to the correct position before use. An incorrectly aligned position may result in incorrect signals. Rotary DIP Switch Operation Item A6R/A6RV Top/Side operation, flat type Screwdriver groove A6A Standard type, flat type 4 0.65 1.0 A6C/A6CV Shaft type, wheel type 4 dia. Top/Side operation type 0.7 2.5 2.9 0.8 Depth: 1.0 Depth: 0.9 Depth: 0.9 Depth: 1.0 Applicable screwdriver: A 1.8 to 2.1 3.5 to 3.8 2.0 to 2.4 Applicable screwdriver: B 0.7 to 0.8 0.4 to 0.5 0.5 to 0.6 Part names A B Flat-blade screwdriver Groove A6A, A6C/A6CV, A6R/A6RV Rotary DIP Switch 5 Precautions Note: Precautions All units are in millimeters unless otherwise indicated. Packing specifications ■ • A6S-H models with embossed taping specifications are shown below. • A6H models with embossed taping specifications are shown below. 2±0.15 1.5±0.1 dia. Perforations 1.5 +0.4 −0.2 dia. Perforations 16±0.15 8±0.15 4±0.15 P=4±0.15 1.75±0.1 2±0.15 B Tape drawing direction A C B±0.15 A +0.4 −0.2 (See note.) Tape drawing direction (ON side) 1.5 dia. holes 2.24 Tape drawing direction D Note: The perforations along both sides are for Switches with 7 poles or more. The perforations on the bottom of the diagram are not provided on Switches with 6 poles or less. Tape drawing direction 13 dia. Applicable models A6H-@10@PM Standard Conforms to JEITA. Standard Conforms to JEITA. Package quantity 4,000 per reel Package quantity 500 per reel 2 4 6 8 12 12 24 24 24 B±0.13 5.5 5.5 11.5 11.5 11.5 A +0.3 −0.1 13 dia. Label 21±0.8 dia. 330±2 dia. 13±0.5 dia. Applicable A6S-@102-PH models Applicable models A6S-@10@PMH Standard Conforms to JEITA. Standard Conforms to JEITA. Package quantity 900 per reel Package quantity 400 per reel Note: 330±2 dia. Applicable A6H-@102-P models No. of poles Three, 2±0.15 Label 10 C (4.2) (6.6) (9.2) (11.7) (14.4) D (18) (18) (30) (30) (30) The dimensions and quantity of A6S-@104-PH/PMH and 1-pole models are different. Enquire for details separately. No. of poles 2 3 4 5 6 7 8 9 A +0.4 −0.2 16 24 24 24 24 32 32 44 10 44 B±0.15 7.5 11.5 11.5 11.5 11.5 14.2 14.2 20.2 20.2 C 6.6 9.1 D (22) (30) (30) (30) (30) (38) (38) (50) (50) E --- --- 11.6 14.2 16.7 19.2 21.7 24.3 26.8 --- --- --- 28.4 28.4 40.4 40.4 6