Y201-EN2-03.book Seite 40 Donnerstag, 30. März 2006 1:52 13
Compact PLC series
CPM1A
Ultracompact and Economical ... For a Wide Range of Uses
AC or DC power, relay or transistor outputs, sourcing or
sinking, etc.
SYSMAC CPM1A
Setting a standard for micro PLCs, the CPM1A packs all
basic functions into a compact size. Four CPU sizes are
available, each with a choice of AC or DC power, relay or
transistor outputs. Select any combination of power
supply, output, and the number of I/O points to meet your
needs.
AC Power Source CPU Units
■Relay Output CPU Unit
CPM1A-10CDR-A-V1
■Transistor Output CPU Units
CPM1A-10CDT-A-V1 (Sink)
CPM1A-10CDT1-A-V1 (Source)
DC Power Source CPU Units
Depth: 70 mm
■Relay Output CPU Unit
CPM1A-20CDR-A-V1
■Transistor Output CPU Units
CPM1A-20CDT-A-V1 (Sink)
CPM1A-20CDT1-A-V1 (Source)
●Input points: 6, DC input
●Output points: 4
■Relay Output CPU Unit
CPM1A-10CDR-D-V1
■Transistor Output CPU Units
CPM1A-10CDT-D-V1 (Sink)
CPM1A-10CDT1-D-V1 (Source)
●Input points: 12, DC input
●Output points: 8
■Relay Output CPU Unit
CPM1A-30CDR-A-V1
● Transistor Output CPU Units
CPM1A-30CDT-A-V1 (Sink)
CPM1A-30CDT1-A-V1 (Source)
●Input points: 6, DC input
●Output points: 4
■Relay Output CPU Unit
CPM1A-40CDR-A-V1
■Transistor Output CPU Units
CPM1A-40CDT-A-V1 (Sink)
CPM1A-40CDT1-A-V1 (Source)
●Input points: 18, DC input
●Output points: 12
■Relay Output CPU Unit
CPM1A-30CDR-D-V1
■Transistor Output CPU Units
CPM1A-30CDT-D-V1 (Sink)
CPM1A-30CDT1-D-V1 (Source)
●Input points: 24, DC input
●Output points: 16
●Input points: 18, DC input
●Output points: 12
Expansion I/O Units
Depth: 50 mm
■Relay Output CPU Unit
CPM1A-20CDR-D-V1
■Transistor Output CPU Units
CPM1A-20CDT-D-V1 (Sink)
CPM1A-20CDT1-D-V1 (Source)
●Input points: 12, DC input
●Output points: 8
■Relay Output CPU Unit
CPM1A-40CDR-D-V1
■Transistor Output CPU Units
CPM1A-40CDT-D-V1 (Sink)
CPM1A-40CDT1-D-V1 (Source)
●Input points: 24, DC input
●Output points: 16
Temperature Sensor Units
CPM1A-20EDR1
CPM1A-8ED
●Input points: 12, DC input
●Output points: 8, RY output
●Input points: 8, DC input
CPM1A-8ER
CPM1A-20EDT
●Output points: 8, RY output
●Input points: 12, DC input
●Output points: 8, TR output (Sink)
CPM1A-8ET
●Output points: 8, TR output (Sink)
CPM1A-20EDT1
CPM1A-8ET1
●Input points: 12, DC input
●Output points: 8, TR output (Source)
●Output points: 8, TR output (Source)
CPM1A-TS001
●Thermocouple inputs: 2
Analog I/O Units
CPM1A-MAD01
(Resolution: 256)
CPM1A-MAD11
(Resolution: 6,000)
2 inputs + 1 output
CPM1A-AD041 (4 inputs)
CPM1A-DA041 (4 outputs)
40
DeviceNet
CPM1A-DRT21
●I/O Link
inputs: 32
●I/O Link
outputs: 32
PROFIBUS-DP
CompoBus/S
PROFIBUS-DP
I/O Link Unit
CPM1A-PRT21
CompoBus/S
I/O Unit
CPM1A-SRT21
●I/O Link
inputs: 16
●I/O Link
outputs: 16
●I/O Link inputs: 8
●I/O Link outputs: 8
CPM1A-TS002
●Thermocouple inputs: 4
CPM1A-TS101
●Pt100 inputs: 2
CPM1A-TS-101-DA
●Pt100 inputs: 2,
Analog outputs: 1
CPM1A-TS102
●Pt100 inputs: 4
Programmable Controllers
Y201-EN2-03.book Seite 41 Donnerstag, 30. März 2006 1:52 13
• Ultracompact Size
Ten-I/O-point AC models measure only 90 mm x 66 mm x 70 mm
(H x W x D), and contain all basic PLC functions.
Programmable
Controllers
Space-saving Integration for Compact machines and Small-scale Control cabinets
Application Example
Changing the speed of a stepping motor.
• A Wide Variety of Models Handling from 10 to 100 I/O Points
By combining CPU Units having from 10 to 40 I/O points with
20-I/O-point Expansion I/O Units, CPM1A PLCs can be configured
for 10 to 100 I/O points.
• Programming by Programmable Terminal
Use of the optional Communications Adapter (RS-232C or RS-422
conversion) enables fast Host Link or NT Link communications with
an OMRON Programmable Terminal. This makes it possible to program the CPM1A on the PT screen, greatly simplifying maintenance tasks.
Output bit 01000 or 01001
• High-speed Processing
Processing is fast, e.g., 0.7-μs AND LD / OR LD and 16.3-μs MOV
instructions, allowing high-speed execution of even lengthy programs. Integrated interrupt and pulse catch inputs also handle
high-speed pulses that occur within one program cycle.
• Versatile Functions in a Compact Body
Stepping
Motor Driver
Stepping
Motor
A large program capacity and instruction list handle even complicated control tasks with ease.
• User memory: 2,048 words
• Data memory: 1,024 words
• Timer/counter: 128 points
• Basic instructions: 14 types
• Application instructions: 79 types
• Analog setting dials: 2 points (built-in)
• Pulse Output
CPM1A CPU models with transistor outputs can output pulses with
a maximum frequency of 2 kHz. Combining these models with a
Stepping Motor Driver or Servo Driver enables easy positioning
operation.
41
Y201-EN2-03.book Seite 42 Donnerstag, 30. März 2006 1:52 13
Functions
Input Interrupts
There are two input interrupts in the CPM1A 10-point I/O CPU and four in the 20-, 30-, and 40-point I/O CPUs.
Input interrupts are available in two modes.
10-point I/O CPU
20-, 30- and 40-point I/O CPU
Application Example:
Cutting Metal Sheets to Specified Lengths
The proximity sensor detects the edge of a metal plate to operate
the cutter. Metal sheets can be cut continuously to the specified lengths
at a high speed.
Metal sheets
Cutter
Conveyor
Cutter
operation
signal
Proximity
sensor
Input
interrupt CPM1A
Input Interrupt Mode
If an input interrupt occurs, the regular program shuts down irrelevant of the cycle time, and the interrupt processing program is
executed immediately.
Regular program
Regular program
Interrupt program
Input interrupt
Counter Mode
When the number of external signals counted at high speed reaches a specified number of counts, the regular program shuts down, and the interrupt processing program is executed at fixed counts. The count can be set between 0 and 65535.
Regular program
Regular program
Interrupt program
Input interrupt
Counter setting
42
Programmable Controllers
Quick-response Inputs
There are two quick-response inputs for the CPM1A 10-point I/O CPU and four for the 20-, 30-, and 40-point I/O CPU (shared with the interrupt
inputs). Since an internal buffer is provided, the quick-response input function can even detect signals modified within one cycle.
CPU
10-point I/O CPU
20-point, 30-point, 40-point I/O CPU
Input no.
Minimum input pulse width
00003 to 00004
00003 to 00006
0.2 ms
Application Example:
Overseeing Program
processes execution
I/O
refreshing
Overseeing Program
processes execution
I/O
refreshing
0.2 ms min
Input signal
(00003)
Calculating the Number of Chips
The metal sensor counts the number of parts that have
passed. Steady counting can be achieved even when
the input-ON time is short.
CPM1A-V1
IR 00003
One cycle
F2LP-WK4
F2LP-W
High-speed Counter
The CPM1A has a high-speed counter function that can be used in the incrementing and up/down mode. Using this function together with the input
interrupts enables zone comparison control or target value control irrelevant of the cycle time.
Item
00000
00001
00002
Input no.
Input method
Count frequency
Count range
Incrementing mode
Count input
--Reset input
Single-phase input
5.0 kHz
0 to 65535
Up/Down mode
A-phase input
B-phase input
Z-phase input
Phase-difference, 4 x inputs
2.5 kHz
-32767 t0 32767
Note: When using in the incrementing mode, the input 00001 can be used as an input contact.
Reset input
00002
00000 or
00001
Count input
Solenoid
Sensor
Rotary encoder
Inverter, etc.
43
Programmable
Controllers
Y201-EN2-03.book Seite 43 Donnerstag, 30. März 2006 1:52 13
Y201-EN2-03.book Seite 44 Donnerstag, 30. März 2006 1:52 13
Interval Timer Interrupts
The CPM1A has one interval timer. The interval timer shuts down the regular program irrelevant of the point in the cycle once the time is up,
and immediately executes an interrupt processing program. Interval timers are used in the following two modes.
Item
Operation
Setting time
One-shot mode
An interrupt is executed only once when the time is up.
0.5 ms to 319,968 ms (0.1-ms units)
Scheduled interrupt mode
Interrupts are executed repeatedly at fixed periods.
Normal program
Application example
Computing the Sheet Speed
The number of pulse inputs is computed in the
interrupt mode at a fixed time to calculate the
speed.
Interval timer
MOV(21)
Interrupt processing program
ADD(30)
SBN(92) 00
CPM1A-V1
Encoder
MOV(21)
RET(93)
END(01)
Analog Setting
The CPM1A contains two analog setting controls that can be used for a broad range of analog timer and counter settings. Turning the setting control
stores values of 0 to 200 (BCD data) in the SR area.
Analog setting
Storage area
Analog setting 0
Analog setting 1
Setting value (BCD)
SR 250
SR 251
0000 to 0200
Application Example:
Analog setting 0
Tact Operation Control of Conveyor Lines
A conveyor can be stopped temporarily as required for assembly
processes. When the timer function and limit switches are used in a
combination, conveyors can be stopped for a fixed time or can be run
at a constant speed for a fixed distance. Fine adjustment of the
stopping time can be easily done by using the analog setting controls.
Analog setting 1
*Phillips screwdriver is required.
Analog setting 0
Analog setting 1
*Phillips screwdriver is required.
Program Example
1. Analog timer for 0.0 to 20.0 seconds
A
2. Analog timer for 0.0 to 60.0 seconds
25313(ON)
TIM
000
250
MUL(32)
250
#0003
DM0500
Value of the analog
setting 0 (0 to 200)
BCD multiplication
Value of the analog setting 0
(0 to 200)
Triples the above value
Multiplication result (0 to 600)
B
TIM
001
44
DM 0500
Programmable Controllers
Y201-EN2-03.book Seite 45 Donnerstag, 30. März 2006 1:52 13
The CPM1A with transistor output has a function that is capable of
outputting a pulse of up to 2 kHz.
When used in combination with a Stepping Driver or Servodriver,
positioning can be easily performed.
Programmable
Controllers
Pulse Output Function
Program Example
1 scan turns ON.
25315
MOV(21)
#5000
DM 0000
Application Example
Sets the number of output pulses as
25,000 (times) in the data memory area.
Changing the speed of the Stepping Motor.
MOV(21)
#0002
DM 0001
DM 0001
0
0
0
DM 0000
2
5
0
0
MOV(21)
#0200
DM 0100
Sets the initial frequency to
2,000 pulses/second.
PULS(65)
Pulse rate setting
0
25315
Output point
01000 or 01001
1 scan turns ON.
000
000
DM 0000
Pulse rate (BCD 8 digits)
00200
@SPED(64)
000
000
DM 0100
Speed change limit switch
00001
MOV(21)
#0020
DM 0100
15000
Stepping Motor Driver
Stepping Motor
25,000 pulses
Output
1 kHZ
frequency
Frequency conversion:
Output port (output point 01000)
Output mode (single)
Frequency data (x 10 Hz)
Changes to 200 Hz when the
limit switch is turned ON.
15000
200 Hz
Pulse rate
00000 turns ON
0001 turns ON (limit switch)
45
Y201-EN2-03.book Seite 46 Donnerstag, 30. März 2006 1:52 13
Communications
Host Link Communications
CPM1A host link communications consist of interactive procedures whereby the CPM1A returns a response to a command sent from
the IBM PC/AT or compatible computer. These communications allow the IBM PC/AT or compatible computer to read and write in the
CPM1A’s I/O Areas and Data Memory Areas as well as in areas containing the status of various settings.
Response
Command
1:1 Host Link Communications
RS-232C
Adapter
CPM1A
CPU
Response
Link Adapter
3G2A9-AL004-E
Command
1:n Host Link Communications
RS-422
Adapter
46
CPM1A
CPU
RS-422
Adapter
CPM1A
CPU
RS-422
Adapter
CPM1A
CPU
Programmable Controllers
Y201-EN2-03.book Seite 47 Donnerstag, 30. März 2006 1:52 13
Programmable
Controllers
1:1 Links
With a 1:1 link, two CPM1As or a CPM1A and CQM1 or C200H# are connected 1:1 with one side as the Master and the other as the Slave to
provide an I/O link of a maximum of 256 points (LR 0000 to LR 1515).
Example of a 1:1 Link between CPM1As
RS-232C Cable
RS-232C Adapter
CPM1A CPU
RS-232C Adapter
CPM1A CPU
Master
Slave
Link bits
Link bits
LR 00
LR 00
WRITE area
WRITE
READ area
LR 07
LR 08
READ area
READ
READ
LR 07
LR 08
WRITE area
LR 15
WRITE
LR 15
Limitations of the CPM1A 1:1 Link
CPM1A I/O links are limited to 16 words (LR 00 to LR 15). Therefore, use these 16 words (LR 00 to LR 15) on the CQM1 or C200H# side when
forming 1:1 links with a CQM1 or C200H#.
NT Links
High-speed communications can be achieved by providing a direct access through the use of the NT Link between the CPM1A and
Programmable Terminal.
Programmable Terminal
RS-232C
Adapter
RS-232C Cable
CPM1A CPU
47
Y201-EN2-03.book Seite 48 Donnerstag, 30. März 2006 1:52 13
System Configuration
CPM1A Line-up
CPU with AC Power Supply
• DC input
• RY output / TR output
AC Power
DC Power
CPU with DC Power Supply
• DC input
• RY output / TR output
Supply Type
Supply Type
L1
L1
L 2 / N COM0
01
03
05
00
02
04
0CH IN : 24V DC 5mA/12mA
NC
L 2 / N COM0
NC
01
00
0CH
03
02
05
04
07
06
08
IN : 24V DC 5mA/12mA
09
10
1CH
11
L1
L2
COM0
NC
01
03
00
0CH
02
05
07
04
06
09
08
11
10
01
03
05
00
02
04
1CH IN : 24V DC 5mA/12mA
11
L1
L2
COM0
0CH
00
IN
1CH
IN
0CH 00
01
02
03
08
09
10
11
10CH 00
01
02
03
04
05
06
07
04
05
06
07
10CH
0CH
IN
OUT
00
01
02
03
10CH 00
01
02
03
04
05
OUT
OUT
ERR
ALM
11CH
ERR
ALM
10CH
00
01
02
COM1 COM2
COM0
10CH
01
02
04
05
00
COM0 COM1 COM2
03
COM3
NC
03
NC
10 I/O points
(Expansion
not possible)
04
05
00
01
02
03
04
05
00
01
02
03
04
05
00
01
02
03
06
07
08
09
10
03
02
05
04
07
06
09
08
11
10
01
00
1CH
03
02
05
04
07
06
09
08
11
10
IN : 24V DC 5mA/12mA
0CH
11
11CH
07
06
1CH
06
10CH
07
OUT
CPM1A-30CDR-A-V1
11CH
NC
Expansion I/O Unit
• DC input
• DC input
• RY output/TR output
• RY output/TR output
02
03
04
05
06
07
08
09
10
11
08
09
10
11
00
01
02
03
04
05
06
07
00
01
02
03
04
05
06
07
00
01
02
03
04
05
06
07
CPM1A-40CDR-A-V1
RUN
ALM
COMM
11CH
07
00
02
NC
NC
06
COM4
01
03
NC
NC
10CH
00
01
02
COM1 COM2
03
COM0
30 I/O points
Expansion I/O Unit
01
PWR
ERR
10CH
00
01
02
04
05
COM0 COM1 COM2
03
COM3
NC
NC
00
IN
ALM
20 I/O points
(Expansion
not possible)
20 I/O points
03
COMM
COMM
COMM
02
RUN
RUN
RUN
01
PWR
PWR
PWR
ERR
01
00
0CH
NC
CPM1A-20CDR-A-V1
CPM1A-10CDR-A-V1
11CH
04
05
07
00
02
04
05
07
NC
NC
NC
COM3
06
COM4
01
03
COM5
06
NC
NC
40 I/O points
DeviceNet I/O
Link Unit
CPM1A-DRT21
PROFIBUS-DP I/O
Link Unit
CPM1A-PRT21
CompoBus/S
I/O Link Unit
CPM1A-SRT21
Analog I/O Unit
CPM1A-MAD01
-MAD11
-AD041
-DA041
Temperature
Sensor Units
CPM1A- TS001
TS002
TS101
TS101-DA
TS102
RS-232C Adapter
CPM1-CIF01
RS-422 Adapter
CPM1-CIF11
8 I/O points
CPM1A System Configuration
Peripheral port
L1
L2
COM0
NC
01
00
0CH
Connecting cable
03
02
05
04
07
06
09
08
11
10
01
03
05
00
02
04
1CH IN : 24V DC 5mA/12mA
11
0CH
06
07
06
07
10CH
00
01
02
04
05
COM1 COM2
03
COM3
06
IN
1CH
10CH
OUT
11CH
00
01
02
03
04
05
00
01
02
03
04
05
00
01
02
03
04
05
00
01
02
03
08
09
10
11
PWR
RUN
ERR
ALM
COMM
COM0
07
11CH
00
COM4
02
01
NC
03
NC
NC
NC
Both AC and DC power supplies.
Expansion I/O Unit
30-point CPU and 40-point CPU only.
May be expanded up to a maximum of 3 Units.
Expansion I/O Unit
Expansion I/O Unit
External Dimensions
CPM1-CIF01
L1
L2/N COM0
NC
01
03
00
02
0CH IN : 24V DC
05
04
30
21
5mA/12mA
CPM1A-10CDR-A-V1
56
50
0CH
IN
OUT
00
01
02
03
10CH 00
01
02
03
04
05
90
PWR
RUN
ERR
ALM
COMM
10CH
00
01
02
COM1 COM2
COM0
W
90
NC
03
NC
81
50
DC power supply
70
AC power supply
Model
CPM1A-10CD@-A-V1
CPM1A-10CD@-D-V1
CPM1A-20CD@-A-V1
CPM1A-20CD@-D-V1
CPM1A-30CD@-A-V1
CPM1A-30CD@-D-V1
CPM1A-40CD@-A-V1
CPM1A-40CD@-D-V1
CPM1A-20ED@
CPM1A-8E@/SRT21
CPM1A-MAD01/TS101-DA
CPM1A-TS@@@/MAD11
CPM1A-DRT21/PRT21
CPM1A-AD041/DA041
48
W (mm)
66
CPM1-CIF11
86
30
21
61
50
130
150
90
81
86 (depth: 50 mm)
66 (depth: 50 mm)
66 (depth: 50 mm)
86 (depth: 50 mm)
66 (depth: 50 mm)
86 (depth: 50 mm)
Programmable Controllers
CPM1A System Configuration Example
A maximum of three Expansion I/O Units can be connected to the CPU Unit. Note that each 4-Channel Analog I/O Unit is counted as two Expansion
Units (Group 2 Units, see Table 2).
L1
L2
COM0
NC
01
00
0CH
03
02
05
04
07
06
09
08
11
10
01
03
05
00
02
04
1CH IN : 24V DC 5mA/12mA
COM
01
03
05
07
09
11
02
04
06
08
10
00
NC
IN
1CH
10CH
OUT
11CH
00
01
02
03
04
05
00
01
02
03
04
05
00
01
02
03
04
05
00
01
02
03
06
07
06
07
08
09
10
11
03
COM
02
01
00
03
02
IN
CH 00 01 02 03
08 09 10 11
CPM1A-30CDR-A-V1
01
00
IN
CH 00 01 02 03 04 05 06 07
0CH
1
COM
CH
IN
0
CH 00 01 02 03
08 09 10 11
08 09 10 11
20EDR1
8ED
8ED
PWR
RUN
ERR
OUT
ALM
CH
COMM
+
10CH
00
01
02
04
05
COM1 COM2
03
COM3
COM0
11CH
00
07
06
COM4
02
01
NC
03
NC
NC
NC
NC
CPU Unit
00 01 02 03 04 05 06 07
CH
00
01
02
04
05
07
NC
COM
COM
COM
03
COM
06
EXP
Expansion I/O Unit
EXP
04
COM
EXP
06
05
04
07
Expansion I/O Unit
COM
06
05
07
Expansion I/O Unit
Connection Groups for Expansion Units
DC Power Supply-type CPM1A Power Consumption
Group 1 (G1)
Expansion I/O Units,
Analog I/O Unit,
CompoBus/S I/O LInk Unit
PROFIBUS-DP I/O Link Unit
DeviceNet I/O Link Unit
CPM1A-TS001/101(-DA)
Use the list below for calculating CPM1A power capacity. The CPM2CPA201 AC Power Supply Unit provides 15 watts of power, so the remainder of the PLC power can be used as service power for sensors or
other components.
Group 2 (G2)
CPM1A-TS002/102
CPM1A-AD041/DA041
CPM1A CPU Unit
In addition to the CPU Unit, Expansion Units from the groups indicated
in the above table can be combined as shown below.
Possible Expansion Unit Combinations
Expansion Unit 1
G1
G2
Expansion Unit 2
G1
G1
Expansion Unit 3
G1
---
Note: 1. Expansion Units 1, 2, and 3 can be mounted in any order.
2. Only one Expansion Unit can be mounted if an NT-AL001 is
connected to the RS-232C port.
CPM1A-10CDR-D-V1
CPM1A-20CDR-D-V1
CPM1A-30CDR-D-V1
CPM1A-40CDR-D-V1
CPM1A-10CDT/T1-D-V1
CPM1A-20CDT/T1-D-V1
CPM1A-30CDT/T1-D-V1
CPM1A-40CDT/T1-D-V1
Power Consumption (W)
3.5
4.5
5.5
6.5
3
3.5
4
4.5
Expandability
Not possible
Not possible
Not possible
Not possible
Add the following power consumption when using Expansion Units.
CPM1A CPU Unit
CPM1A-20EDR1
CPM1A-20EDT/T1
CPM1A-8ED
CPM1A-8ER
CPM1A-8ET/T1
CPM1A-SRT21/DRT21/PRT21
CPM1A-MAD01/MAD11
CPM1A-TS001/TS101(-DA)
CPM1A-TS002/TS102
CPM1A-AD041
CPM1A-DA041
Power Consumption (W)
2.5
1.5
1
2
1
1
3.5
3
3
3
3.3
The power consumption for the CPU Unit includes that of the
Programming Console, RS-232C Adaptor, etc.
49
Programmable
Controllers
Y201-EN2-03.book Seite 49 Donnerstag, 30. März 2006 1:52 13
Y201-EN2-03.book Seite 50 Donnerstag, 30. März 2006 1:52 13
Specifications
General Specifications
Item
Power supply vol tage/frequency
Operating voltage range
Power consumption
Inrush current
External power supply
( AC only)
AC power supply
DC power supply
AC power supply
DC power supply
AC power supply
DC power supply
Power supply voltage
Power supply output capacity
Insulation resistance
Dielectric strength
Noise resistance
Vibration resistance
Shock resistance
Ambient temperature (operating)
Ambient humidity (operating)
Ambient environment (operating)
Ambient temperature (storage)
Terminal screw size
Power supply holding time
Weight
10-point I/O
20-point I/O
100 to 240 V AC, 50/60 Hz
24 V DC
85 to 264 V AC
20.4 to 26.4 V DC
30 V AC max.
(See below.)
30 A max.
24 V DC
200 mA
30-point I/O
40-point I/O
60 V AC max.
60 A max.
300 mA
20 MΩ min. at 500 V DC between the AC terminals and the protective earth terminal.
2,300 V AC at 50/60 Hz for one minute with a leakage current of 10 mA max. between all the external AC
terminals and the protective earth terminal.
Conforms to IEC61000-4-4, 2 kV (power lines)
10 to 57 Hz with an amplitude of 0.075 mm, and 57 to 150 Hz with an acceleration of 9.8 m/s2 in the X, Y,
and Z directions for 80 minutes each (i.e. swept for 8 minutes, 10 times).
147 m/s2 in the X, Y and Z directions 3 times each.
0° to 55° C
10% to 90% (no condensation)
With no corrosive gas
–20° to 75° C
M3
10 ms min. for AC models, and 2 ms min. for DC models
AC model: 400 g max.
AC model: 500 g max.
AC model: 600 g max.
AC model: 700 g max.
DC model: 300 g max.
DC model: 400 g max.
DC model: 500 g max.
DC model: 600 g max.
Note: The specifications of the Expansion I/O Unit are the same as for the CPU except that the power is supplied from the CPU and the weight is
300 g.
50
Programmable Controllers
Performance Specifications
Item
Control method
I/O control method
Programming language
Instruction word
Types of
instructions
Basic instructions
Special instructions
Instruction execution time Basic instructions
Special instructions
Program capacity
Maximum I/O points
CPU only
With Expansion I/O Unit
Input bits
Output bits
Work bits (IR Area)
System bits (SR Area)
Temporary bits (TR Area)
Holding bits (HR Area)
Auxiliary bits (AR Area)
Link bits (LR Area)
Timers/Counters
Data memory
Read/Write
Read only
Interrupt processing: External interrupt
Memory protection
Memory backup
Self-diagnostic function
Program check
Pulse output
High-speed counter
Quick-response inputs
Input time constant
Analog settings
10-point I/O
20-point I/O
30-point I/O
40-point I/O
Stored program method
Combination of the cyclic scan and immediate refresh processing methods.
Ladder diagram
1 step per instruction, 1 to 5 words per instruction
14 types
79 types, 139 instructions
0.72 to 16.2 μs
MOV instruction = 16.3 μs
2,048 words
10 points (6 input/4 output
20 points (12 input/8 out- 30 points (18 input/12
40 points (24 input/16
points)
put points)
output points)
output points)
----90 points (54 input/36
100 points (60 input/40
output points)
output points)
00000 to 00915 (Words 0 to 9)
01000 to 01915 (Words 10 to 19)
512: IR 20000 to IR 23115 (IR 200 to IR 231)
384: SR 23200 to SR 25515 (SR 232 to SR 255)
8: TR 0 to TR 7
320: HR 0000 to HR 1915 (HR 00 to HR 19)
256: AR 0000 to AR 1515 (AR 00 to AR 15)
256: LR 0000 to LR 1515 (LR 00 to LR 15)
128:TIM/CNT 000 to 127
100-ms timer: TIM 000 to TIM 127
10-ms timer: TIM 000 to TIM 127
Decremental counter, reversible counter
1,024 words (DM 0000 to DM 1023)
512 words (DM 6144 to DM 6655)
2 points (Response time of 0.3 4 points (Response time of 0.3 ms max.)
ms max.)
Maintains the contents of the HR, AR, Counter and Data Memory Areas.
Flash memory:User program, data memory (Read only) (Non-battery powered storage)
Super capacitor:Data memory (Read/Write), holding bits, auxiliary memory bits, counter
(20-day storage at an ambient temperature of 25° C)
CPU error (watchdog timer), memory errors, I/O bus errors
No END instruction, programming errors (constantly checked during operation)
1 point: 2 kHz
1 point:Single phase at 5 kHz or two-phase at 2.5 kHz (linear counting method)
Incremental mode: 0 to 65535 (16-bit)
Decremental mode:–32767 to 32767 (16-bit)
1 point:Single phase at 5 kHz or two-phase at 2.5 kHz (linear counting method)
Incremental mode: 0 to 65535 (16-bit)
Decremental mode:–32767 to 32767 (16-bit)
Together with the external interrupt input (minimum pulse width of 0.2 ms)
Can be set at 1 ms, 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, or 128 ms.
2 points: (0 to 200)
Note: Bits that are not used for the I/O bits can be used as work bits.
51
Programmable
Controllers
Y201-EN2-03.book Seite 51 Donnerstag, 30. März 2006 1:52 13
Y201-EN2-03.book Seite 52 Donnerstag, 30. März 2006 1:52 13
I/O Specifications
Input Circuit
CPU
Item
Input voltage
Specifications
24 V DC +10%/–15%
Circuit
Input impedance
IN00000 to IN00002: 2 kΩ
Others: 4.7 kΩ
Input current (typical)
IN00000 to IN00002: 12 mA
Others: 5 mA
ON voltage
14.4 V DC min.
OFF voltage
5.0 V DC max.
ON delay (see note 1)
1 to 128 ms max. (default: 8 ms) (see note 1)
OFF delay (see note 1)
1 to 128 ms max. (default: 8 ms) (see note 1)
Input
LED
IN
4.7 kΩ (2 kΩ)
820 Ω
(510 Ω)
COM
Internal Circuits
Note: The polarity of the input power supply can be either
positive or negative.
Resistance values in parentheses are for inputs
IN00000 to IN00002.
Note: 1. The actual ON/OFF delay includes a digital filter with a time constant of 1, 2, 4, 8, 16, 32, 64, or 128 ms (default: 8 ms).
2. The delays for IN00000 to IN00002 are as follows when used for the high-speed counter.
Input
IN00000 (A-phase)
IN00001 (B-phase)
IN00002 (Z-phase)
Increment mode
5 kHz
Normal input
ON: 100 μs max. OFF: 500 μs max.
Differential phase mode
2.5 kHz
3. The delays for IN00003 to IN00006 are as follows when used for the high-speed counter.
0.3 ms max. (From the time of input ON until the interrupt subroutine is executed.)*1
Delay
*1
For detailed specifications of expansion I/O units, see page 68.
Expansion I/O Unit
Item
Input voltage
Input impedance
Input current (typical)
ON voltage
OFF voltage
ON delay (see note 1)
OFF delay (see note 1)
Specifications
24 V DC +10%/–15%
4.7 kΩ
5 mA
14.4 V DC min.
5.0 V DC max.
1 to 128 ms max. (default: 8 ms) (see note 1)
1 to 128 ms max. (default: 8 ms) (see note 1)
Circuit
Input
LED
IN
4.7 kΩ
820 Ω
Internal Circuits
COM
Note: The polarity of the input power supply can be either
positive or negative.
Note: The actual ON/OFF delay includes an input constant of 1, 2, 4, 8, 16, 32, 64, or 128 ms (default: 8 ms).
Output Circuit
CPU and Expansion I/O Unit
Relay Output
Item
Specifications
Maximum switching capacity 250 V AC/2 A (cosφ =1)
24 V DC/2 A (4 A/common)
Minimum switching capacity 5 V DC, 10 mA
Relay
Elec- Resistive 150,000 times (at 24 V DC)
service trical load
life
Inductive 100,000 times (at 200 V AC, cosφ =0.4)
load
Mechanical
20 million times
ON delay
15 ms max.
OFF delay
15 ms max.
52
Circuit
Output
LED
OUT
L
L
Internal Circuits
OUT
COM
Maximum
250 VAC: 2 A
24 VDC: 2A
Programmable Controllers
Y201-EN2-03.book Seite 53 Donnerstag, 30. März 2006 1:52 13
Item
Maximum switching capacity
Leakage current
Residual voltage
ON delay
OFF delay
Specifications
24 V DC +10%/–15%, 300 mA (see note 1)
0.1 mA max.
1.5 V max.
0.1 ms max.
1 ms max. (see note 2)
Programmable
Controllers
Transistor Output (Sink Type/Source Type) (CPU/Expansion I/O Unit)
Circuit
Sink Type
Output LED
Source Type
Output LED
OUT
COM
L
L
OUT
Internal Circuits
Internal Circuits
L
L
COM
Note: 1. The maximum switching capacity of the CPM1A with transistor outputs (sink type and source type) is limited to the currents shown in the following table for
the common and for the Unit.
Item
10CDT-V1/
20CDT-D-V1/
10CDT1-A-V1/D-V1 20CDT1-A-V1/D-V1
Max. switching capacity 0.9 A/Unit
0.9 A/common
1.8 A/Unit
30CDT-D-V1/
30CDT1-A-V1/D-V1
0.9 A/common
2.7 A/Unit
40CDT-D-V1/
20EDT/20EDT1
40CDT1-A-V1/D-V1
0.9 A/common
0.9 A/common
3.6 A/Unit
1.8 A/Unit
CPM1A-8ET/8ET1
2. When using the pulse output function of the CPM1A with transistor outputs (sink type and source type):
The output current must be between 100 to 200 mA when using the output 01000 or 01001 as a pulse output with the maximum frequency of 2 kHz.
The off-delay of outpus 01000 and 01001 will vary depending on the output current.
Load current
100 to 200 mA
0 to 300 mA except for the above range
OFF delay
0.2 ms max.
0.5 ms max.
Analog I/O Unit
Item
Analog
inputs
Number of inputs
Input signal ranges
CPM1A-MAD01
Voltage I/O
Current I/O
2
0 to 10 V or 1 4 to 20 mA
to 5 V
CPM1A-MAD11
Voltage I/O
Current I/O
2 (allocated 2 words)
0 to 5 V, 1 to 5 0 to 20 mA, 4
V, 0 to 10 V, – to 20 mA
10 to 10 V
Maximum rated input
±15 V
±30 mA
±15 V
±30 mA
External input impedance
1 MΩ min.
250 Ω rated
1 MΩ min.
250 Ω
Resolution
1/256
1/6,000 (full scale)
Overall precision
1.0% of full scale
25° C:±0.3% of 25° C:±0.4% of
full scale
full scale
0 to
0 to
55° C:±0.6% of 55° C:±0.8% of
full scale
full scale
Converted A/D data
8-bit binary data
Binary data (4-digit hexadeciFull scale = 0000 to 00FF Hex mal)
–10 to 10 V: F448 to 0BB8
Hex full scale
Other:0000 to 1770 Hex full
scale
Averaging
--Supported (set for each input
with DIP switch)
Disconnection detection
--Supported
Analog
Number of outputs
1
1 (1 word allocated )
output
Output signal ranges
0 to 10 V or – 4 to 20 mA
1 to 5 V, 0 to 0 to 20 mA, 4
(See note
10 to 10 V
10 V, –10 to to 20 mA
1.)
10 V
External output allowed load 2 kΩ min.
350 Ω max.
1 kΩ min.
600 Ω max.
resistance
External output impedance --0.5 Ω max.
--Resolution
1/256 (1/512 when the output 1/6,000 (full scale)
signal range is –10 to 10 V.)
Overall precision
1.0% of full scale
25°C:±0.4% of full scale
0 to 55°C:±0.8% of full scale
D/A data setting
8-bit plus sign binary data
Binary data (hexadecimal, 4-10 to 10 V output range: Full digit)
scale = 80FF to 00FF Hex
–10 to 10 V output range: Full
4 to 20 mA output range: Full scale = F448 to 0BB8 Hex
scale = 0000 to 00FF Hex
Other output ranges: Full
scale = 0000 to 1770 Hex
Conversion time
10 ms/Unit max. (See note 2.) 2 ms/point
Isolation method
Photocoupler isolation bePhotocoupler isolation between I/O terminals and PC tween analog I/O and internal
(There is no isolation between circuits. (Individual analog I/O
the analog I/O signals.)
signals are not isolated.)
CPM1A-AD041
CPM1A-DA041
Voltage I/O
Current I/O
Voltage I/O
Current I/O
4 (allocated 4 words in +
2 words out)
0 to 5 V, 1 to 5 0 to 20 mA, 4
V, 0 to 10 V, – to 20 mA
10 to 10 V
±15 V
±30 mA
1 MΩ min.
250 Ω
1/6,000 (full scale)
25° C:±0.3% of 25° C:±0.4% of
full scale
full scale
0 to
0 to
55° C:±0.6% of 55° C:±0.8% of
full scale
full scale
Binary data (4-digit hexadecimal)
–10 to 10 V: F448 to 0BB8
Hex full scale
Other:0000 to 1770 Hex full
scale
Supported (set for each input
with DIP switch)
Supported
4 (4 words allocated)
1 to 5 V, 0 to 0 to 20 mA, 4
10 V, –10 to to 20 mA
10 V
1 kΩ min.
600 Ω max.
0.5 Ω max.
--1/6,000 (full scale)
25°C:±0.4% of full scale
0 to 55°C:±0.8% of full scale
Binary data (hexadecimal, 4digit)
–10 to 10 V output range: Full
scale = F448 to 0BB8 Hex
Other output ranges: Full
scale = 0000 to 1770 Hex
2 ms/point
2 ms/point
Photocoupler isolation bePhotocoupler isolation between analog I/O and internal tween analog I/O and internal
circuits. (Individual analog I/O circuits. (Individual analog I/O
signals are not isolated.)
signals are not isolated.)
Note: 1. The voltage output and current output can be used at the same time, but the total output current cannot exceed 21 mA.
2. The conversion time is the total time for 2 analog inputs and 1 analog output.
53
Y201-EN2-03.book Seite 54 Donnerstag, 30. März 2006 1:52 13
Temperature Sensor Units
By mounting a Temperature Sensor Unit (CPM1A-TS001/TS002/TS101/TS102) to the PLC, input can be obtained from a thermocouple or platinum
resistance thermometer, and temperature measurements can be converted to binary data (4-digit hexadecimal) and cyclically updated in the input
area of the CPU Unit.
Specifications
Item
Model
Number of inputs
Input types
Indication accuracy
Conversion time
Converted temperature data
Isolation method
Specifications
CPM1A-TS001/002
2 (TS001), 4 (TS002)
Thermocouple K, J switchable
(Note: Same type for all input points.)
The larger of ±0.5% of the indicated value and ±2°C ±1 digit max.
CPM1A-TS101/102
2 (TS101), 4 (TS102)
Pt100, JPt100 switchable
(Note: Same type for all input points.)
[The larger of ±0.5%of the indicated value and ±1°C]
±1 digit max.
250 ms/2 points (TS001, TS101); 250 ms/4 points (TS002, TS102)
Binary (4-digit hexadecimal)
Photocoupler isolation between the temperature input signals.
Note: The indication accuracy when using a K-type thermocouple for temperatures less than –100°C is ±4°C ±1 digit max.
Input Temperature Ranges for CPM1A-TS001/002
The rotary switch can be used to make of the following range and input type settings for CPM1A-TS001/002 models.
Input type
K
J
Range (°C)
–200 to 1300
0.0 to 500.0
–100 to 850
0.0 to 400.0
Range (°F)
–300 to 2300
0.0 to 900.0
–100 to 1500
0.0 to 750.0
Input Temperature Ranges for CPM1A-TS101/102
The rotary switch can be used to make of the following range and input type settings for CPM1A-TS101/102 models.
Input type
Pt100
JPt100
Range (°C)
–200.0 to 650.0
–200.0 to 650.0
Range (°F)
–300 to 1200.0
–300 to 1200.0
Specifications CPM1A-TS101-DA
Item
Model
Number of inputs
Input types
Temperature range
Converted temperature data
Indication accuracy
Number of outputs
Output type
Load resistance
Output resolution
Output accuracy
Conversion time
Isolation method
Specifications
CPM1A-TS101-DA
2
Pt100
-40 to 250°C
16-bit, 2’s complement, 0.1°C resolution
1.0% of full scale max.
1
0 to 10 V, -10 to 10 V, 4 to 20 mA
2 kΩ min. (voltage output), 500Ω max. (current output)
8 bit + sign (1/256, 1/512 for -10 to 10 V)
1.0% of full scale max.
60 ms (all channels)
Photocoupler isolation between I/O signals and PLC
DeviceNet I/O Link Unit - CPM1A-DRT21
By connecting the DeviceNet I/O Link Unit (CPM1A-DRT21), the CPM1A can function as the slave of a DeviceNet Master Unit.
In this configuration, 32 input- and 32 output bits are exchanged with the Master Unit.
Specifications
Item
Master/slave
Number of I/O points allocated to Master
Number of words allocated from CPM1A’s I/O memory
Node address setting method
Specification
DeviceNet Slave
Input: 32 points / Output: 32 points
Input: 2 words / Output: 2 words
(Allocated in the same way as other Expansion Units).
Set using DIP switch.
PROFIBUS-DP I/O Link Unit - CPM1A-PRT21
By connecting the PROFIBUS-DP I/O Link Unit (CPM1A-PRT21), the CPM1A can function as the slave of any PROFIBUS-DP Master Unit.
In this configuration, 16 input- and 16 output bits are exchanged with the Master unit.
Specifications
Item
Master/slave
Number of I/O points allocated to Master
Number of words allocated from CPM1A’s I/O memory
Node address setting method
54
Specification
PROFIBUS-DP slave (OC_0658.GSD)
Input: 16 points / Output: 16 points (Intel/Motorola format selectable by DIP switch)
Input: 1 word / Output: 1 word
(Allocated in the same way as other Expansion Units).
0-99 using 2 rotary switches
Programmable Controllers
Y201-EN2-03.book Seite 55 Donnerstag, 30. März 2006 1:52 13
Programmable
Controllers
CompoBus/S I/O Link Unit - CPM1A-SRT21
Specifications
Item
Master/Slave
Number of I/O bits
Number of words occupied in CPM2A I/O memory
Specification
CompoBus/S Slave
8 input bits, 8 output bits
1 input word, 1 output word
(Allocated in the same way as other Expansion Units).
Set using the DIP switch. (Set before turning ON power for the CPU Unit.)
Node number setting
Communications Adapter Specifications CPM1-CIF01/CIF11
RS-232C Adapter and RS-422 Adapter
Item
Specifications
CPM1-CIF01
Level conversion between the CMOS level (CPU side) and the
RS-232C level (peripheral device side)
The RS-232C (peripheral device side) is insulated by a DC/DC
converter and photocoupler.
Power is supplied by the CPU.
200 g max.
Functions
Isolation (all in this line)
Power supply
Weight
CPM1-CIF11
Level conversion between the CMOS level (CPU side) and the
RS-422 level (peripheral device side)
The RS-422 (peripheral device side) is insulated by a DC/DC
converter and photocoupler.
Expansion Memory Unit CPM1A-EMU01-V1
The CPM1-EMU01-V1 offers simple onsite transfer of user programs and data memory.
Item
Supported PLCs
Read/write memory areas
Specifications
CPM1, CPM1A, CPM2A, CPM2C, SRM1(-V2), CQM1, CQM1H
User Program: 15.2 kWords max.
Data memory: DM 6144 to DM 6655
Espansion instructions
18 instructions
EEPROM
256-Kbit EEPROM, ATMEL: AT28C256, OMRON: EEROM-JD
Current consumption
130 mA max.
Dimensions (not including cables 57 x 92 x 38 mm (W x H x D)
or connectors)
Weight
200 g max. (not including EEPROM)
Specifications
CPM2C-PA201 AC Power Supply Unit
• The CPM2C-PA201 is a slim and compact AC Power Supply Unit of the same shape as the CPM2C’s CPU Unit. It can be
connected simply using the connecting cable (23 cm) provided. It can also be used for CPM1A and CPM2A CPU Units and as
display power supply (wired by the user).
AC Power Supply Unit
AC Power Supply Unit
Service power supply
for external devices
such as sensors (24 V).
Attached connecting cable
Item
Rated output
Output voltage
Output current
Efficiency
Input conditions
Rated voltage
Allowable voltage range
Frequency
Current
100 V
200 V
Leakage current
100 V
200 V
Inrush current
100 V
200 V
Specification
15 W
24 V
600 mA
75% min. (at rated output)
100 to 240 V AC
85 to 264 V AC
47 to 63 Hz
0.4 A
0.2 A
0.5 mA max. (at rated output)
1 mA max. (at rated output)
15 A max. (at 25° C cold start)
30 A max. (at 25° C cold start)
55
Y201-EN2-03.book Seite 56 Donnerstag, 30. März 2006 1:52 13
Item
Output
characteristics
Output voltage accuracy
Minimum output current
Ripple noise voltage
Input fluctuation
Load fluctuation
Temperature fluctuation
Startup time
Output hold time
Overcurrent protection
Overvoltage protection
Ambient operating temperature
Ambient storage temperature
Ambient operating humidity
Dielectric strength
Insulation resistance
Vibration resistance
Shock resistance
Noise terminal voltage
Weight
Specification
10%/–15% (including input, load, and temperature fluctuations)
30 mA
2% (p-p) max.
0.75% max.
4% max.
0.05%/° C max.
300 ms max. (at input voltage of 100 V AC or 200 V AC and the rated output)
10 ms (at input voltage of 100 V AC or 200 V AC and the rated output)
Self-resetting, operates at 105% to 335% of the rated current, suspended and independent operation
None
0° to 55° C
–20° to 75° C (no condensation or icing)
10% to 90% (no condensation)
2,000 V for 1 min between all inputs and GR
Leakage current: 10 mA
3,000 V for 1 min between all inputs and all outputs
Leakage current: 10 mA
1,000 V for 1 min between all outputs and GR
Leakage current: 10 mA
100 MΩ min. at 500 V DC between all outputs and any input, and between all outputs and GR
10 to 57 Hz, amplitude, 57 to 150 Hz, acceleration: 9.8 m/s2 in X, Y, and Z directions for 80 minutes
according
(Time coefficient: 8 minutes × coefficient factor 10 = total time 80 min.)
147 m/s2 3 times each in X, Y, and Z directions
FCC class A
250 g max.
Peripheral Devices
IBM PC/AT or compatible
CPM1A CPU
CX-One:
Omron's integrated software for programming
and configuration of all control system components, including PLCs, HMI, drives, temperature controllers and advanced sensors.
CX-One
RS-232C
USB
USB-Serial Conversion Cable
CS1W-CIF31
Peripheral Device Connecting Cable
CQM1-CIF02
Programming Console
Connecting Cable
Programming
Console
C200H-PRO27-E
Programming Console
(With Connecting Cable)
CQM1-PRO01-E
C200H-CN222/CN422
(2 m/4 m)
56
Programmable Controllers
CPM1A Ordering Information
International Standards
The products shown in the attached tables are those that conform to the UL, CSA, cULus, cUL, NK, Lloyd’s Register, and EC Directives as of
September 2003.
(U: UL, C: CSA, UC: cULus, CU: cUL, N: NK, L: Lloyd, CE: EC Directives)
Please contact OMRON representative for application conditions.
CPU Units
Name
10-point
I/O
Power supply
AC power supply
DC power supply
20-point
I/O
AC power supply
DC power supply
30-point
I/O
AC power supply
DC power supply
40-point I/O
AC power supply
DC power supply
Output method
Relay output
Transistor output (sink type)
Transistor output (source type)
Relay output
Transistor output (sink type)
Transistor output (source type)
Relay output
Transistor output (sink type)
Transistor output (source type)
Relay output
Transistor output (sink type)
Transistor output (source type)
Relay output
Transistor output (sink type)
Transistor output (source type)
Relay output
Transistor output (sink type)
Transistor output (source type)
Relay output
Transistor output (sink type)
Transistor output (source type)
Relay output
Transistor output (sink type)
Transistor output (source type)
Input points
6 points
12 points
18 points
24 points
Output points
4 points
8 points
12 points
16 points
Model
CPM1A-10CDR-A-V1
CPM1A-10CDT-A-V1
CPM1A-10CDT1-A-V1
CPM1A-10CDR-D-V1
CPM1A-10CDT-D-V1
CPM1A-10CDT1-D-V1
CPM1A-20CDR-A-V1
CPM1A-20CDT-A-V1
CPM1A-20CDT1-A-V1
CPM1A-20CDR-D-V1
CPM1A-20CDT-D-V1
CPM1A-20CDT1-D-V1
CPM1A-30CDR-A-V1
CPM1A-30CDT-A-V1
CPM1A-30CDT1-A-V1
CPM1A-30CDR-D-V1
CPM1A-30CDT-D-V1
CPM1A-30CDT1-D-V1
CPM1A-40CDR-A-V1
CPM1A-40CDT-A-V1
CPM1A-40CDT1-A-V1
CPM1A-40CDR-D-V1
CPM1A-40CDT-D-V1
CPM1A-40CDT1-D-V1
Standards
U, C, N, L, CE
U, C, CE
U, C, N, L, CE
U, C, CE, N
U, C, N, L, CE
U, C, CE
U, C, N, L, CE
U, C, CE, N
U, C, N, L, CE
U, C, CE
U, C, N, L, CE
U, C, CE, N
U, C, N, L, CE
U, C, CE
U, C, N, L, CE
U, C, CE, N
Expansion Units and Expansion I/O Units
Unit
Input/Output type
Expansion I/O Units Relay
Transistor (sinking)
Transistor (sourcing)
Relay
Transistor (sinking)
Transistor (sourcing)
--Relay
Transistor (sinking)
Transistor (sourcing)
Analog I/O Unit
Analog
(resolution: 1/256)
Analog
(resolution: 1/6000)
Analog
(resolution: 1/6000)
Analog
(resolution: 1/6000)
DeviceNet I/O Link --Unit
PROFIBUS-DP
--I/O Link Unit
CompoBus/S I/O
--Link Unit
Temperature Sensor 2 thermocouple inputs
Units
4 thermocouple inputs
Inputs
24
Outputs
16
1
Model
CPM1A-40EDR
CPM1A-40EDT
CPM1A-40EDT1
CPM1A-20EDR1
CPM1A-20EDT
CPM1A-20EDT1
CPM1A-8ED
CPM1A-8ER
CPM1A-8ET
CPM1A-8ET1
CPM1A-MAD01
Standards
CE, N
CE, N
CE, N
U, C, CE, N
U, C, CE, N
U, C, CE, N
U, C, CE, N
U, C, CE, N
U, C, CE, N
U, C, L, CE, N
U, C, CE, N
12
8
8
-----
--8
8
2
2
1
CPM1A-MAD11
U, C, CE, N
4
---
CPM1A-AD041
U, C, CE
---
4
CPM1A-DA041
U, C, CE
I/O Link of 32 input bits and 32 output bits
CPM1A-DRT21
U, C, CE, N
I/O Link of 16 input bits and 16 output bits
CPM1A-PRT21
CE
I/O Link of 8 input bits and 8 output bits
CPM1A-SRT21
U, C, CE, N
CPM1A-TS001
U, C, CE, N
CPM1A-TS002
U, C, CE, N
2 platinum resistance thermometer inputs
CPM1A-TS101
U, C, CE, N
4 platinum resistance thermometer inputs
CPM1A-TS102
U, C, CE, N
2 Platinum resistance thermometer inputs
(-40 to 250 °C) and one output (-10 to 10V, 4 to 20 mA)
CPM1A-TS101-DA
U, C, L, CE
57
Programmable
Controllers
Y201-EN2-03.book Seite 57 Donnerstag, 30. März 2006 1:52 13
Y201-EN2-03.book Seite 58 Donnerstag, 30. März 2006 1:52 13
RS-232C Adapter, RS-422 Adapter, Connecting Cable, Link Adapter
Name
RS-232C Adapter
RS-422 Adapter
Connecting Cable
Function
Converts peripheral port levels.
Model
CPM1-CIF01
CPM1-CIF11
3.3-m cable used to connect IBM PC/AT or compatible personal com- CQM1-CIF02
puters.
Converts RS-232C and RS-422 levels.
3G2A9-AL004-E
Link Adapter
Standards
N, L, CE
U, C, N, L, CE
---
Programming Consoles and Cables
Product
Programming Console (2-m cable attached)
Programming Console (Requires separate cable. See below.)
Connecting Cable for C200H-PRO27-E
2-m cable
4-m cable
Model
CQM1-PRO01-E
C200H-PRO27-E
C200H-CN222
C200H-CN422
Standards
U, C, N, CE
U, C, N, CE
N
---
Support Software
Product
CX-One
*1
Functions
Model
Omron's integrated software for programming and configuration of all control system components, CX-ONE-AL@@C-E*1
including PLCs, HMI, drives, temperature controllers and advanced sensors.
Standards
---
@@ = Number of licenses (01, 03, 10)
Product
Expansion Memory Unit
EEPROM (256 K)
Model
CPM1-EMU01-V1
EEROM-JD
Standards
-----
Model
CPM2C-PA201
Standards
U, C, CE
Power Supply Unit
Unit
Power Supply
58
Input
100 to 240 V AC
Output
24 V DC/600 mA
Programmable Controllers
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change without notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the importation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security interest in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original transportation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
14.
15.
16.
17.
18.
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for published information.
Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or settle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
Property; Confidentiality. Any intellectual property in the Products is the exclusive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law principles). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability. If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Companies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this Product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
2.
3.
4.
5.
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website
at www.omron247.com – under the “About Us” tab, in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ELECTRONICS LLC
1 Commerce Drive
Schaumburg, IL 60173
Tel: 847.843.7900
For U.S. technical support or other
inquiries: 800.556.6766
OMRON CANADA, INC.
885 Milner Avenue
Toronto, Ontario M1B 5V8
Tel: 416.286.6465
MEXICO SALES OFFICES
Mexico, D.F.
555.660.3144
Ciudad Juárez
656.623.7083
Monterrey, N.L.
818.377.4281
Querétaro
442.135.4510
BRAZIL SALES OFFICE
Sao Paulo
55.11.2101.6310
ARGENTINA SALES OFFICE
Cono Sur
54.114.787.1129
CHILE SALES OFFICE
Santiago
562.206.4592
OMRON ON-LINE
Global www.omron.com
USA www.omron247.com
Canada www.omron.ca
Brazil www.omron.com.br
Latin America www.espanol.omron.com
OTHER LATIN AMERICAN SALES
mela@omron.com
Cat. No. P06E-EN-03A............................5/07............Specifications subject to change without notice..............Printed in USA
工商网监
湘ICP备2023018690号
