CS1WCN713

Programmable Controller CQM1H The CQM1H’s rack-less modular design lets you customize your control system by adding “inner boards” for advanced functions, as well as specialized I/O and communications modules. CQM1H offers the most flexibility of all PLC systems in its class. D D D D D D D D D D 4 different base CPUs to choose from; 16 DC inputs built in; expands up to 512 points No separate backplane required Inner Boards allow “customized” configuration of the CPU Serial communications inner board supports protocol macro feature for communication with third-party serial devices Supports all existing and new CQM1 I/O and specialized I/O modules Optional memory cassettes allow backup of sensitive data, provides a real-time clock ControllerLink network transmits 8 kword data packets at up to 2 Mbps; 32 nodes Advanced instruction set includes PID, floating point math, protocol macro instructions and more CompoBus/S, SYSMAC BUS and AS-interface masters support remote I/O Up to 15.2 kwords of program memory Basic Configuration Select the CPU and I/O modules (discrete, analog and dedicated special function types) then determine the power supply based on the current consumption. The I/O Control and Interface adapters give you the option of dividing the CPU and I/O system into two narrower units than the examples shown below. The CQM1H-CPU51/CPU61 models offer space-saving position and motion control solutions as well as additional analog and serial communications capabilities right at the CPU. CQM1H modules are assembled with connectors on their sides. 256 or 512 I/O points max. CPU Unit Power Supply A--152 Controller Link Module Inner 16 built-in I/O Modules Boards inputs and Dedicated I/O Modules Programmable Controller CQM1H End Cover 11 modules max. (16 modules max. using I/O Expansion and Control Interface adapters). The total number of words cannot exceed 16. Ordering Information J CPU Stock Note: Shaded models are normally stocked. Specifications Memory capacity Max. I/O capacity Built-in inputs Built-in RS-232C port Support of Inner Boards Support of Controller Link Unit Program: g 3.2 kwords DM area: 3 kwords k d 256 p points 16 DC i inputs t No No No Program: 7.2 kwords DM area: 6 kwords 512 points Yes Yes International standards t d d Part number U,, C,, N,, CE CQM1H-CPU11 Yes CQM1H-CPU21 CQM1H-CPU51 Program: 15.2 kwords DM area: 6 kwords EM area: 6 kwords CQM1H-CPU61 J POWER SUPPLY MODULES Stock Note: Shaded models are normally stocked. Item Specifications Rated voltage AC power supply modules DC power supply modules 100 to VAC 240 VAC, 50/60 Hz Allowed voltage range 85 to 265 VAC International t d d standards Part number None U, C, N, L, CE CQM1-PA203 30 W 24 VDC, 0.5 A U, C, L, N CQM1-PA206 Output capacity Service power supply 18 W 110/230 VAC, 50/60 Hz 80 to 138 VAC 160 to 276 VAC 30 W 24 VDC, 0.5 A CE CQM1-PA216 24 VDC 20 to 28 VDC 30 W — U, C, N, L, CE CQM1-PD026 J MEMORY CASSETTES Stock Note: Shaded models are normally stocked. Memory Memory capacity/Clock function International standards Part number Flash memoryy 16 kwords U,, C,, N,, CE CQM1H-ME16K with clock EEPROM CQM1H-ME16R U,, C,, N,, L,, CE 8 kwords with clock CQM1-ME08R 4 kwords CQM1-ME04K with clock EPROM memory cassette ((Memory e o y chip c p not o included) c uded) CQM1-ME04R Cassette with IC socket only (EPROM chip sold separately) CQM1-MP08K with clock EPROM chip CQM1-ME08K CQM1-MP08R 128 KB (8 kwords), 150 ns, 27128 IC or equivalent, 12.5 V L ROM-ID-B 256 KB (16 kwords), 150 ns, 27256 IC or equivalent, 12.5 V CE ROM-JD-B 512 KB (32 kwords), 150 ns, 27512 IC or equivalent, 12.5 V Programmable Controller ROM-KD-B CQM1H A--153 J I/O EXPANSION AND CONTROL INTERFACE ADAPTERS Stock Note: Shaded models are normally stocked. Use I/O Expansion and Control Interface adapters for applications that require 11 to 16 I/O modules. Memory Memory capacity/Clock function International standards Part number I/O control adapter Connects to right-hand side of CPU block U,, C,, CE CQM1H-IC101 I/O interface adapter Connects to left-hand side of Expansion I/O block I/O / extension cable Connects the I/O / control module l tto th the I/O interface i t f module d l Cable length: 0.3 m CQM1H-II101 L,, CE Cable length: 0.7 m CS1W-CN313 CS1W-CN713 Note: U: UL, C: CSA, N: NK, L: LLOYD, CE: EC Directives J I/O MODULES Stock Note: Shaded models are normally stocked. Input Modules Input type Number of inputs Input voltage Input current Common type Connector type International standards Part number DC inputs p 8 12 to 24 VDC 10 mA Independent CQM1-ID211 12 VDC 6 mA Shared Terminal bl k block U, C, N, L, CE 16 U, C CQM1-ID111 U, C, N, L, CE CQM1-ID212 U, C CQM1-ID112 U, C, N, L, CE CQM1-ID213 U,, C,, L,, CE CQM1-IA121 24 VDC 32 4 mA Shared Connector 100 to 120 VAC 5 mA Shared 200 to 240 VAC 6 mA Terminal bl k block 12 VDC 24 VDC AC inputs p 8 CQM1-IA221 Output Modules Output type Number of outputs Max. switching voltage Max. switching current Common type Connector type Contact outputs t t 8 250 VAC,, 24 VDC 2A Independent 16 Shared 8 Transistor Transistor Triac 8 Independent 24 VDC 2 A (NPN) 16 0.3 A (NPN) 32 0.1 A (NPN) 8 24 VDC 1 A (PNP) 16 0.3 A (PNP) 32 0.5 A (PNP) 8 240 VAC 0.4 A 6 A--154 Terminal bl k block Programmable Controller Shared (f (fused) d) Terminal bl k block International standards Part number U,, C,, N,, L CQM1-OC221 CQM1-OC222 CE, U CQM1-OC224 U,, C,, N,, L,, CE CQM1-OD211 CQM1-OD212 Connector Shared (f (fused) d) Shared (short circuit propro tected CQM1H CQM1-OD213 Terminal bl k block U,, C,, L,, CE Connector CE CQM1-OD216 Terminal block U, C, L CQM1-OA221 CE CQM1-OA222 CQM1-OD215 CQM1-OD214 J INNER BOARDS Stock Note: Shaded models are normally stocked. Item Specifications International standards Part number High-speed counter board 4 pulse inputs (high-speed counter) at 500 kHz max. 4 external outputs U, C, N, CE CQM1H-CTB41 Pulse I/O board 2 pulse inputs: Single-phase: 50 kHz, Differential phase: 25 kHz U, C CQM1H-PLB21 2 pulse outputs: 50 kHz max., both fixed and variable duty factors are supported. Absolute encoder interface board 2 absolute encoder (gray code binary) inputs (4 kHz) U, C, N CQM1H-ABB21 Analog setting board 4 analog settings U, C, N, CE CQM1H-AVB41 Analog I/O board 4 analog inputs of 0 to 5 V, 0 to 20 mA, --10 to +10 V 2 analog outputs of 0 to 20 mA, --10 to +10 V CE CQM1H-MAB42 Serial communications board One RS-232C port and one RS-422A/RS-485 port U, C, N, CE CQM1H-SCB41 Note: U: UL, C: CSA, N: NK, L: LLOYD, CE: EC Directives J COMMUNICATION MODULES Stock Note: Shaded models are normally stocked. Controller Network Module Item Specifications International standards Part number Controller Link module (wired) Data link (Maximum number of words per node: 8,000) Communications instructions: SEND/RECV/CMND U, C, CE CQM1H-CLK21 Item Specifications Part number CompoBus/S master module Number of I/O points per Master: 128 (64 inputs and 64 outputs; ) Communications cycle time: 0.5 ms min. Max. transmission distance: 500 m in long-distance mode 100 m in high-speed mode Max. slaves per master: 32 International standards U, C, CE Field Network Modules SYSMAC BUS modules Remote master (*Use G730 transistor and relay output modules.) Connects CQM1H to G730 SYSMAC BUS remote I/O modules; max. 64 I/O (32 or 16 inputs or outputs, DIP switch selectable) Number of I/O points per Master: 128 Communications cycle time: 187.5 kbps Max. transmission distance: 200 m One master and two expansions allowed per system Input Expands G730 input capacity of G730 remote master; expansion adds 32 or 16 inputs, DIP switch selected Output Expands G730 output capacity of G730 remote master; expansion adds 32 or 16 outputs, DIP switch selected DeviceNet I/O link module Number of I/O points: 16 inputs and 16 outputs Maps the 16 inputs and 16 outputs as a single node. Profibus-DP I/O link unit Number of I/O points: 128 inputs and 128 outputs AS-interface master module Number of I/O points: 248 (124 inputs and 124 outputs; 4 inputs/4 outputs per slave) Communications cycle time: 5.148 ms min. Max. transmission distance: 100 m; 300 m with 2 repeaters Max. slaves per master: 31 slaves per master module CQM1-SRM21-V1 CQM1-G7M21 CQM1-G7N11 CQM1-G7N01 CQM1-DRT21 U, C, CE U, C, CE CQM1-PRT21 CQM1-ARM21 Note: *G730 transistor and relay output modules are shown in the Complementary Products section in this catalog. Programmable Controller CQM1H A--155 J DEDICATED I/O MODULES Stock Note: Shaded models are normally stocked. Item Specifications International standards Part number Analog g I/O / modules Analog inputs: 4 points, built-in power supply U, C, N, CE CQM1-AD042 Analog inputs: 4 points, order separate power supply U, C, N, CE CQM1-AD041 Analog outputs: 2 points, built-in power supply Analog outputs: 2 points, order separate power supply U,, C,, N,, CE CQM1-DA022 Power Supply Module required for AD041 and DA021 modules B7A Master link modules* CQM1-DA021 For one Analog module CQM1-IPS01 For two Analog modules CQM1-IPS02 16 outputs — CQM1-B7A02 16 inputs U,, C CQM1-B7A12 32 outputs CQM1-B7A03 32 inputs Temperature controller p d l modules Temperature controller p d l ((continued) ti d) modules CQM1-B7A13 16 inputs and 16 outputs — CQM1-B7A21 Thermocouple input, transistor (NPN) output, 2 loops U, C, CE CQM1-TC001 Thermocouple input, transistor (PNP) output, 2 loops CQM1-TC002 Platinum resistance thermometer input, transistor (NPN) output, 2 loops CQM1-TC101 Platinum resistance thermometer input, transistor (PNP) output, 2 loops CQM1-TC102 Thermocouple input, transistor (NPN) output, 4 loops U,, C,, CE CQM1-TC201 Thermocouple input, transistor (PNP) output, 4 loops CQM1-TC202 Thermocouple input, transistor (NPN) output, 2 loops (with heater burnout alarm) CQM1-TC203 Thermocouple input, transistor (PNP) output, 2 loops (with heater burnout alarm) CQM1-TC204 Platinum resistance thermometer input, transistor (NPN) output, 4 loops CQM1-TC301 Platinum resistance thermometer input, transistor (PNP) output, 4 loops CQM1-TC302 Platinum resistance thermometer input, transistor (NPN) output, 2 loops (with heater burnout alarm) CQM1-TC303 Platinum resistance thermometer input, transistor (PNP) output, 2 loops (with heater burnout alarm) CQM1-TC304 Linear sensor interface d l modules Standard — Safety relay module Emergency stop unit: 2 inputs/2 outputs, 4 generalpurpose inputs With monitor output CQM1-LSE01 CQM1-LSE02 U, C CQM1-SF200 Note: U: UL, C: CSA, N: NK, L: LLOYD, CE: EC Directives *B7A Slave Link Modules are listed in the Dedicated I/O Modules section describing B7A Master Link Modules. A--156 Programmable Controller CQM1H J PROGRAMMING DEVICES AND ACCESSORIES Stock Note: Shaded models are normally stocked. Programming Consoles Item Specifications International standards Part number Programming consoles 2-m Connecting Cable included (No other Connecting Cables required.) U, C, CE CQM1H-PRO01-E Requires a separate Connecting Cable, see below. U, C, N, CE C200H-PRO27-E Cable length: 2 m N C200H-CN222 Cable length: 2 m (for CPUs complying with EC directives) CE C200HS-CN222 Cable length: 2 m CE CS1W-CN224 Cable length: 6 m CE CS1W-CN624 Connects the peripheral port on the CQM1H to a personal computer or Programming Console through a CQM1-CIF02 cable. CE CS1W-CN114 Connecting g cables Peripheral port conversion cable Communications Adapters and Cables Description Function Cable length Part number Cables and adapters p DB 9-pin p on computer p to CQM1H Q mini-peripheral p p port p 2m CS1W-CN226 6m CS1W-CN626 Serial port p on computer p to Omron DB 9-pin p serial port p 2m C200HS-CN220-EU 25-9 pin interface to Omron PLC p cable,, operator p 50 cm NT31C-CN510-EU 3m NT31C-CN320-EU CBL-202* CBL-803* 25-9 pin cable, operator interface to Omron PLC 5m NT31C-CN520-EU Operator interface to Omron peripheral port p p p p cable 2m XW2Z-200T-2 5m XW2Z-500T-2 50 cm C200H-CN510-EU 3m C200H-CN320-EU 9-9 pin p cable,, operator p interface to Omron PLC CBL-804* 5m C200H-CN520-EU Serial port p on computer p to Omron DB 9-pin p serial port p 2m C200H-CN229-EU Converts the CQM1H CPU mini-peripheral port to an RS-232C port 0.1 m CS1W-CN118 Converts CQM1-CIF02 peripheral connector to CQM1H’s mini-peripheral port 0.05 m CS1W-CN114 Cable mounted communication adapter converts peripheral port to DB 9-pin serial port 3.3 m CQM1-CIF02 Mini-peripheral port to RS-422 adapter, DIN mount — CQM1H-CIF12 Item Specifications Cable length International standards Part number CX-Programmer Write and debug programs; monitor operation CD-ROM — — WS02-CXPC1-E-Vj.j Item International standards Part number Expansion memory unit uploads and downloads program and setup memory areas to and from the controller. — CPM1-EMU01-V1 EEPROM (256 kbits) — EEPROM-CPM1-EMU01 CBL-202* * Available in Canada only. Software Program Transfer Tools Programmable Controller CQM1H A--157 J MAINTENANCE PRODUCTS Stock Note: Shaded models are normally stocked. Item Function International standards Part number Battery Backs up memory in the CPU. — CPM2A-BAT01 End cover Connects to the I/O module located on the extreme right U, C, CE CQM1H-TER01 International standards Part number L PFP-50N J DIN TRACK Stock Note: Shaded models are normally stocked. Item Specifications Mounting g track Track length: 50 cm Height: g 7.3 mm Track length: 1 m Track length: 1 m End plate PFP-100N Height: 16 mm Fasten mounting brackets on both sides of the PLC to prevent it from sliding left or right. PFP-100N2 PFP-M Note: U: UL, C: CSA, N: NK, L: LLOYD, CE: EC Directives J MANUALS Product Description Part number Operation manual CQM1H CPUs and Inner Boards operation manual W363 Programming manual CQM1H CPUs and Inner Boards programming manual W364 Dedicated I/O Modules manual Covers analog input/output, B7A Link master, temperature controller, linear sensor interface, and safety relay modules. W238 A--158 Programmable Controller CQM1H CPUs The four models of CPUs can be broadly divided into two groups: Models that support Inner Boards and the Controller Link Unit, and models that do not. The CPUs also vary in their program capacities, I/O capacities, memory capacities, and the presence of an RS-232C port, as shown in the Basic Specifications table, below. J NOMENCLATURE The following illustration shows the main components of a CQM1H-CPU61 CPU. Sliders Used to secure adjacent Units. Battery Compartment Cover Open this cover to access the battery, DIP switch, and Memory Cassette. Connector Add on Units horizontally by joining connectors. LED indicators Mini-Peripheral Port Used to connect to Programming Devices such as a Programming Console or a computer running CX-Programmer. Also supports Host Link and no-protocol communications. Built-in Inputs There are 16 inputs built into CPU Unit. Inner Board Covers Remove these covers when installing or removing Inner Boards. RS-232C Port (except CQM1H-CPU11) Used for Host Link, no-protocol, 1:1 Data Link, or NT link (1:1 mode) communications with external devices or other PLCs. Inner Board Slot 2 (right slot) Use this slot to mount a High-speed Counter Board, Pulse I/O Board, Absolute Encoder Interface Board, Analog Setting Board, or Analog I/O Board. Inner Board Slot 1 (left slot) Use this slot to mount a High-speed Counter Board, Analog Setting Board, or Serial Communications Board. J OVERVIEW Model CQM1H-CPU61 I/O capacity (See Note.) Note ) Program capacity (words) DM capacity (words) EM capacity (words) CPU Unit built-in inputs Built-in serial ports Peripheral port RS-232C port 512 15.2 K 6K 6K DC: 16 Yes Yes 7.2 K 6K None 3.2 K 3K CQM1H-CPU51 CQM1H-CPU21 256 Inner Boards Controller Link Module Supported pp Not supported pp CQM1H-CPU11 No J MAXIMUM NUMBER OF MODULES CPU Controller Link Module Inner Boards I/O Modules and Dedicated I/O Modules CQM1H-CPU61 1 max. 2 max. Not supported. pp Not supported. pp 11 max. 16 max. using i I/O Expansion E i and d Control Interface modules CQM1H-CPU51 CQM1H-CPU21 CQM1H-CPU11 Note: I/O capacity = Number of input points (≤ 256) + Number of output points (≤ 256). Programmable Controller CQM1H A--159 J CPU UNIT SPECIFICATIONS Characteristics Item Specifications Control method Stored program method I/O control method Cyclic scan and direct output/immediate interrupt processing Programming language Ladder-diagram programming I/O capacity CQM1H-CPU11/21: 256 CQM1H-CPU51/61: 512 Program capacity CQM1H-CPU11/21 : 3.2 kwords CQM1H-CPU51 : 7.2 kwords CQM1H-CPU61 : 15.2 kwords User data memory capacity CQM1H-CPU11/21 : 3 kwords CQM1H-CPU51 : 6 kwords CQM1H-CPU61 : 12 kwords (DM: 6 kwords; EM: 6 kwords) Instruction length 1 step per instruction, 1 to 4 words per instruction Number of instructions 162 (14 basic, 148 special instructions) Instruction execution times Basic instructions: 0.375 to 1.125 µs Special instructions: 17.7 µs (MOV instruction) Overseeing time 0.70 ms Mounting structure No backplane (Modules are joined horizontally using connectors) Mounting DIN Track mounting (screw mounting not possible) CPU built-in DC input points 16 Maximum number of modules Maximum of 11 modules total for I/O modules and Dedicated I/O modules Inner Boards CQM1H-CPU11/21: None CQM1H-CPU51/61: 2 Boards Communications modules (Controller Link Module) CQM1H-CPU11/21: None CQM1H-CPU51/61: 1 module Types of interrupts Input Interrupt Mode: Interrupts are executed in response to inputs from external sources to the CPU’s built-in input points. Input interrupts (4 inputs max.) Counter Mode: Interrupts are executed in response to reception of a set number of pulses (counted down) via the CPU’s internal built-in input points (4 points). Interval timer interrupts (3 timers max.) Scheduled Interrupt Mode: Program is interrupted at regular intervals measured by one of the CPU’s internal timers. High-speed counter interrupts Target Value Comparison: Interrupt is executed when the high-speed counter PV is equal to a specified value. One-shot Interrupt Mode: An interrupt is executed after a set time, measured by one of the CPU’s internal timers. Range Comparison: Interrupt is executed when the high-speed counter PV lies within a specified range. Counting is possible for high-speed counter inputs from the CPU’s internal input points, Pulse I/O Boards, or Absolute Encoder Interface Boards. (The High-speed Counter Board has no interrupt function, but can output bit patterns internally and externally.) I/O allocations A--160 I/O is automatically allocated in order from the Unit nearest to the CPU. (Because there are no I/O tables, it is not necessary to create I/O tables from a Programming Device.) Programmable Controller CQM1H Memory Area Structure Data area Size Words Bits Function IR area Input area 256 bits IR 000 to IR 015 IR 00000 to IR 01515 Input bits are allocated to Input Units or Dedicated I/O Units. The 16 bits in IR 000 are always allocated to the CPU’s built-in inputs. Bits in IR 001 to IR 015 are allocated to I/O or Dedicated I/O Units connected to the CPU. IR area Output area Work areas a eas 256 bits IR 100 to IR 115 IR 10000 to IR 11515 2,528 bits min. IR 016 to IR 089 IR 01600 to IR 08915 Output bits are allocated to Output Units or Dedicated I/O Units connected to the CPU. Work bits do not have any specific function and they can be freelyy used within the t t e program. p og a IR 116 to IR 189 IR 11600 to IR 18915 IR 216 to IR 219 IR 21600 to IR 21915 IR 224 to IR 229 IR 22400 to IR 22915 IR 090 to IR 095 IR 09000 to IR 09515 Status Area 1: Stores the Controller Link data link status information. IR 190 to IR 195 IR 19000 to IR 19515 Status Area 2: Stores the Controller Link error and network participation information. Used when the MACRO instruction, MCRO(99), is used. Controller Link status areas a eas MACRO operand ope a d area 96 bits Input area 64 bits IR 096 to IR 099 IR 09600 to IR 09915 Output area 64 bits IR 196 to IR 199 IR 19600 to IR 19915 256 bits IR 200 to IR 215 IR 20000 to IR 21515 Inner Board slot 1 area (A minimum 2,528 bits are available as work bits. Most bits in the IR and LR areas can be used as work bits when they are not used for their allocated functions, so the total number of available work bits depends on the configuration of the PLC.) These bits are allocated to the Inner Board mounted in slot 1 of a CQM1H-CPU51/61. High-speed Counter Board: IR 200 to IR 213 Serial Communications Board: IR 200 to IR 207 Analog settings area 64 bits IR 220 to IR 223 IR 22000 to IR 22315 Used to store the analog settings when a CQM1H-AVB41 Analog Setting Board is mounted. High-speed Counter, 0 PV 32 bits IR 230 to IR 231 IR 23000 to IR 23115 Used to store the present values of high-speed counter 0. Inner Board slot 2 area 192 bits IR 232 to IR 243 IR 23200 to IR 24315 These bits are allocated to the Inner Board mounted in slot 2. SR area 184 bits SR 244 to SR 255 SR 24400 to SR 25507 These bits serve specific functions such as flags and control bits. HR area 1,600 bits HR 00 to HR 99 HR 0000 to HR 9915 These bits store data and retain their ON/OFF status when power is turned OFF or when the operating mode is changed. AR area 448 bits AR 00 to AR 27 AR 0000 to AR 2715 These bits serve specific functions such as flags and control bits. TR area 8 bits — TR 0 to TR 7 These bits are used to temporarily store ON/OFF status at program branches. LR area 1,024 bits LR 00 to LR 63 LR 0000 to LR 6315 Used for 1:1 data link through the RS-232 port or through a Controller Link module. Timer/Counter area 512 bits TIM/CNT 000 to TIM/CNT 511 (timer/counter numbers) High-speed Counter Board: Absolute Encoder Interface Board: Pulse I/O Board: Analog I/O Board: IR 232 to IR 243 IR 232 to IR 239 IR 232 to IR 239 IR 232 to IR 239 The same numbers are used for both timers and counters. Timer numbers 000 to 015 can be used with TIMH(15) for interrupt-refreshed PVs to ensure proper timing without inaccuracy being caused by the cycle time. (This table continues on the next page.) Programmable Controller CQM1H A--161 Memory Area Structure -- continued from previous page Data area DM area Read/ write e Readonly Size Words Bits Function 3,072 words DM 0000 to DM 3071 — DM area data can be accessed in word units only. Word values are retained when the power is turned OFF. 3,072 words DM 3072 to DM 6143 — Available in CQM1H-CPU51/61 CPUs only. 425 words DM 6144 to DM 6568 — Cannot be written from the program (only from a Programming Device). DM 6400 to DM 6409: DM 6450 to DM 6499: DM 6550 to DM 6559: Controller Link parameters Routing tables Serial Communications Board Setup Error history area 31 words DM 6569 to DM 6599 — Cannot be written from the program (only from a Programming Device). Stores the time of occurrence and error code of errors that occur. PLC setup 56 words DM 6600 to DM 6655 — Cannot be written from the program (only from a Programming Device). Stores various parameters that control PLC operation. 6,144 words EM 0000 to EM 6143 — EM area data can be accessed in word units only. Word values are retained when the power is turned OFF or the operating mode is changed. (CQM1H-CPU61 CPU Unit only.) EM area Other Functions Item Specification Macro instructions Subroutines called by instructions containing arguments. Min. cycle time 1 to 9,999 ms (Unit: 1 ms) Cycle time monitoring When the cycle time exceeds 100 ms, the Cycle Time Over Flag turns ON, and operation continues. (A setting can be made in the PLC Setup so that this error is not generated.) When the cycle time exceeds the cycle monitor time, operation is stopped. Cycle monitor time settings: 0 to 990 ms in 10-ms units, 0 to 9,900 ms in 100-ms units, 0 to 99 s in 1-s units. The maximum and current values of the cycle time are stored in the AR area. I/O refreshing Cyclic refreshing, refreshing by IORF(97), direct output refreshing (set in the PLC Setup), interrupt input refreshing. (The inputs that are refreshed can be set separately for input interrupts, high-speed counter interrupts, and interval timer interrupts in the PLC Setup.) I/O memory status when changing operating mode Depends on the ON/OFF status of the I/O Hold Bit (SR 25212). Load OFF All outputs on Output Units can be turned OFF when the CPU is operating in RUN, MONITOR, or PROGRAM mode. (Used for stopping output in emergencies, for debugging, etc.) A pin setting on the DIP switch on the front of the CPU is stored in AR 0712. This setting can be used as an ON/OFF condition (e.g., to switch between trial operation and actual operation). Possible User-customized DIP switch setting Mode setting at power-up Debugging Online editing Program protection Error check Forced set/reset, differential monitoring, data tracing (scheduled, cyclic, or when instruction is executed). User programs can be overwritten in program-block units when the CPU is in MONITOR mode. With the CXProgrammer, more than one program block can be edited at the same time. Write-protection of user program and data memory (DM 6144 to DM 6655: read-only DM): Set using pin 1 of the DIP switch. User-defined errors (i.e., user can define fatal errors and non-fatal errors using the FAL(06) and FALS(07) instructions.) (It is possible to stop operation using FALS(07) for fatal errors. User-defined error logs can be created in specific bits (logging) when using FAL(06). Error log Serial communications Up to 10 errors (including user-defined errors) are stored in the error log. Information includes the error code, error details, and the time the error occurred. Built-in mini-peripheral port: Programming Device (including Programming Console) connections, Host Links, no-protocol communications Built-in RS-232C port: Programming Device (excluding Programming Console) connections, Host Links, no-protocol communications, NT Links (1:1 mode), 1:1 Data LInks RS-232C port and RS-422A/485 port on Serial Communications Board (sold separately): Programming Device (excluding Programming Console) connections, Host Links, no-protocol communications, NT Links (1:1 mode, 1:N mode), 1:1 Data LInks, protocol macros (This table continues on the next page.) A--162 Programmable Controller CQM1H Other Functions -- continued from previous page Specification Item Serial communications modes Built-in mini-peripheral port Built-in RS-232C port Serial communications board Programming console bus Connects to Programming Console. YES (pin 7 OFF) No No Peripheral bus Connects to a computer running CX-Programmer or other Support Software. (Automatically used if the network type is set to peripheral bus on the Support Software.) YES (pin 7 ON) No No Host Link (SYSMAC WAY) Enables reading/writing CPU I/O memory or program using Host Link commands. Computers running Support Software or OMRON Programmable Terminals can also be connected. PLC-initiated communications are possible. YES (pin 7 ON) YES YES No-protocol Enables sending or receiving up to 256 bytes of data without a protocol or data conversion. A start code, end code, and transmission delay can be set. YES (pin 7 ON) YES YES 1:1 data link Enables 1:1 data link with a CQM1H, CQM1, CPM-series, C200HX/HG/HE, C200HS, or SRM1 PLC. No YES YES NT links (1:1 and 1:N) Enables 1:1 or 1:N communications with OMRON Programmable Terminals without additional programming. No YES (1:1 only) YES (1:1 and 1:N) Protocol macros Enables user-created protocols to communicate with essential any device equipped with a serial communications port (e.g., RS-232C). Standard protocols are also provided. No No YES Clock Some Memory Cassette are equipped with a clock. (The time of the error will recorded if a clock is used.) Input time constants Used to set the ON (or OFF) response times for DC Input modules. Settings: 1, 2, 4, 8, 16, 32, 64, and 128 ms. AC power supply: 10 to 25 ms (not fixed), DC power supply: 5 to 25 ms (not fixed) Power OFF detection time Memory protection Held Areas: Holding bits, contents of Data Memory and Extended Data Memory, and status of the counter Completion Flags and present values. If the I/O Hold Bit (SR 25212) is turned ON, and the PLC Setup is set to maintain the I/O Hold Bit status when power is turned ON, the contents of the IR area and the LR area will be saved. Commands to a host computer Remote programming and monitoring Host Link command responses can be sent to a computer connected via the Host Link System using the TXD(—) (communications port output) instruction. Host Link or peripheral bus communications via a CPU’s serial communications port can be used for remote programming and remote monitoring of the PLC through a Controller Link System. (This function is, however, not supported for the serial communications ports on the Serial Communications Board.) Program check Program is checked at the beginning of operation for items such as no END(01) instruction and instruction errors. CX-Programmer can also check programs. (The level of program checking can be set.) Battery life 5 years at 25_C (Depends on the ambient temperature and power supply conditions. Min.: 1 yr) Battery replacement must be performed within 5 minutes. Errors from selfdiagnostics Other functions CPU (watchdog timer), I/O verification, I/O bus, memory, FALS system (FALS execution or cycle monitor time over), FAL system (FAL execution or PLC Setup error etc.), battery, cycle time over and communications port. Storage of number of times power has been interrupted. (Stored in AR area.) Programmable Controller CQM1H A--163 Power Supply Units Both AC and DC Power Supply Units are available. The AC Power Supply Units require a power supply input from 100 to 240 VAC and two of the AC Power Supply Units are equipped with an auxiliary 24 VDC power supply output. The CQM1H’s left End Cover is part of the Power Supply Unit. CQM1-PA206 CQM1-PA216 CQM1-PA203 CQM1-PD026 J SPECIFICATIONS Item CQM1-PA203 Supply voltage CQM1-PA206 CQM1-PA216 CQM1-PD026 100 to 240 VAC, 50/60 Hz 100 or 230 VAC (selectable), 50/60 Hz 24 VDC Operating voltage range 85 to 264 VAC 85 to 132 VAC or 170 to 264 VAC 20 to 28 VDC Operating frequency range 47 to 63 Hz Power consumption 60 VA max. Inrush current 30 A max. Output capacity 5 VDC: 3.6 A (18 W) Insulation resistance 20 MΩ min. at 500 VDC between AC external terminals and GR terminals Dielectric strength 2,300 VAC 50/60 Hz for 1 min between AC external and GR terminals, leakage current: 10 mA max. — 120 VA max. 50 W max. 5 VDC: 6 A 24 VDC: 0.5 A (30 W total) 5 VDC: 6 A (30 W) 1,000 VAC 50/60 Hz for 1 min between DC external and GR terminals, leakage current: 20 mA max. Noise immunity Conforms to IEC61000-4-4, 2 kV (power lines) Vibration resistance 10 to 57 Hz with an amplitude of 0.075 mm, and 57 to 150 Hz with an acceleration of 9.8 m/s2 in the X, Y, and Z directions for 80 minutes each (i.e., swept for 8 minutes, 10 times). Shock resistance 147 m/s2 (118 m/s2 for Contact Output Units) 3 times each in X, Y, and Z directions Ambient temperature Operating: 0° to 55°C (32° to 131°F) Storage: --20° to 75°C (--4° to 167°F), except battery Ambient operating humidity 10% to 90% RH (no condensation) Operating environment No corrosive gas Ground Less than 100 Ω Construction Panel mounted Weight 5 kg max. Internal current consumption CQM1H-CPU11: CQM1H-CPU21/51/61: Dimensions (without cables) CQM1H-CPU11/21: 187 to 571 ¢ 110 ¢ 107 mm (W¢H¢D) CQM1H-CPU51/61: 187 to 603 ¢ 110 ¢ 107 mm (W¢H¢D) Accessories RS-232C connector (one XM2A-0901 Plug and one XM2S-0911-E Hood) (except CQM1H-CPU11) CPM2A-BAT01 Battery Set (installed in CPU Unit when shipped) 820 mA at 5 VDC 840 mA at 5 VDC Note: The total power consumed at 5 VDC and 24 VDC must be less than 30 W. (5 × Current consumed at 5 VDC) + (24 × Current consumed at 24 VDC) ≤ 30 W A--164 Programmable Controller CQM1H I/O Expansion Adapters Use Expansion I/O adapters to split the configuration into more than one group, allowing greater flexibility with mounting space as well as the use of at least 16 I/O Modules or Dedicated I/O Modules. Expansion Adapters can be used with any CQM1H CPU. CQM1H-IC101 CQM1H-II101 J SPECIFICATIONS Maximum Number of Units Mountable CPU model CQM1H-CPU61 CPU Block only CPU Block + I/O Expansion Adapter CPU grouping CPU grouping I/O Modules + Dedicated I/O Modules Controller Link Modules Inner Boards I/O Modules + Dedicated I/O Modules I/O Modules + Dedicated I/O Modules 11 Modules max. 1 Module 2 Boards max. 5 Modules max. 11 Modules max. Not supported pp Not supported pp Extension grouping CQM1H-CPU51 CQM1H-CPU21 CQM1H-CPU11 J CONFIGURATION 5 Modules max. CPU Grouping Total current consumption: 3.0 A max. (including CPU) I/O Control Adapter (CQM1H-IC101) End Cover (included with CPU Unit) I/O Extension Cable CS1W-CN313 (0.3 m) or CS1W-CN713 (0.7 m) End Cover (included with I/O Interface Module) I/O Interface Adapter (CQM1H-II101) Extension Grouping Total current consumption: 2.0 A max. (I/O Modules and Dedicated I/O Modules) 11 Modules max. Note: If the CQM1-PA203 Power Supply Unit is used, the maximum current consumption total is 3.6 A. Programmable Controller CQM1H A--165 Memory Cassettes An optional Memory Cassette can be used to store the user program, PLC setup, and other data in ROM so that vital data will not be lost in the event of battery expiration or careless programming/monitoring operations. If the PLC’s settings need to be changed to execute another process, the entire software setup and user program can be changed just by exchanging the Memory Cassette and rebooting the PLC. EEPROM: Flash Memory: EPROM: CQM1-ME04K CQM1-ME04R CQM1-ME08K CQM1-ME08R CQM1H-ME16K CQM1H-ME16R CQM1-MP08K CQM1-MP08R J SPECIFICATIONS Memory Model Specifications EEPROM CQM1-ME04K 4 kwords without clock CQM1-ME04R 4 kwords with clock CQM1-ME08K 8 kwords without clock CQM1-ME08R 8 kwords with clock CQM1-MP08K Without clock (see below) CQM1-MP08R With clock (see below) CQM1H-ME16K 16 kwords without clock CQM1H-ME16R 16 kwords with clock EPROM Flash Memory Cassette (EEPROM or flash memory) Mounted from the front of the CPU and used to store and read the user’s program, DM (read-only DM and PLC Setup), and expansion instruction information as one block. It is possible to set the CPU so that data stored in the Memory Cassette (user’s program, DM, expansion instruction information) is automatically sent to the CPU (auto-boot) at startup. Transfer and comparison of data between the CPU and Memory Cassette are possible using AR area control bits. EPROM Chips The following EPROM chips (sold separately) are required for EPROM Memory Cassettes. The chip is mounted in the I/O socket on the Memory Cassette. Model ROM version Capacity Access speed ROM-ID-B 27128 or equivalent 8 kwords 150 ns ROM-JD-B 27256 or equivalent 16 kwords 150 ns ROM-KD-B 27512 or equivalent 32 kwords 150 ns A--166 Programmable Controller CQM1H Inputs and Outputs for CPUs and Modules J I/O MEMORY ALLOCATION I/O words are allocated to I/O Modules according to a fixed location. When the I/O Modules and Dedicated I/O Modules are connected, the I/O words will be allocated as follows. Input Word Allocation Input Words Built-in CPU inputs (16 DC inputs) IR 000 (Fixed) 32-point Input Module IR 001 IR 002 16-point Input Module IR 003 IR 000 to IR 015 are allocated as input bits. The first input word (IR 000), however, is allocated to the CPU’s 16 built-in input points. Note: Built-in CPU’s inputs are used for interrupt processing and built-in high-speed counter inputs. Output Word Allocation IR 100 to IR 115 are allocated as output bits. When Output Modules or Dedicated I/O Modules are connected, words will be allocated in order starting from IR 100. Output Words 8-point Output Module IR 103 16-point Output Module IR 102 16-point Output Module IR 101 16-point Output Module IR 100 Programmable Controller CQM1H A--167 I/O Word Allocation Module type I/O word allocation Input words Output words Description Input module 1 or 2 — Each 8-point or 16-point input module is allocated one input word and each 32-point input module is allocated two input words. Words will be allocated in order starting from IR 001. Output modules — 1 or 2 Each 8-point or 16-point output module is allocated one output word and each 32-point output module is allocated two output words. Words will be allocated in order starting from IR 100. B7A02 — 1 B7A12 1 — Depending p g on the module,, each B7A Master link module is allocated input p words d and d output t t words. d B7A03 — 1 B7A13 2 — B7A21 1 1 DeviceNet I/O link module 1 1 Each DeviceNet I/O link module is allocated one input word and one output word. Profibus-DP I/O /O link d l module IN: 32 points OUT: 32 points 2 2 The Profibus-DP master configuration data must match this setting. IN: 64 points OUT: 64 points 4 4 IN: 96 points OUT: 96 points 6 6 IN: 128 points OUT: 128 points 8 8 IN: 44 points OUT: 44 points 3 3 IN: 60 points OUT: 60 points 4 4 IN: 92 points OUT: 92 points 6 6 IN: 76 points OUT: 76 points 5 5 IN: 92 points OUT: 92 points 6 6 IN: 124 points OUT: 124 points 8 8 IN:16 points OUT: 16 points 1 1 IN: 32 points OUT: 32 points 2 2 IN: 64 points OUT: 64 points 4 4 Analog input module 2 or 4 — Each analog input module can be set to input either 2 or 4 points. If the module is set to input 2 points, two input words are allocated. If the module is set to input 4 points, four input words are allocated. Analog output module — 2 Each analog output module is allocated two output words. Analog power supply modules for CQM1-AD041 and -DA021 — — Power supply modules are not involved directly in I/O operations and are thus not allocated I/O words. Temperature control modules 00j/10j 2 or 1 2 or 1 Each temperature control module is allocated two input words and two output words when two loops are used. Only one input word and one output word are allocated when one loop is used. 20j/30j 1 1 One input word and one output word are allocated in the order the module is connected. 1 — One input word is allocated per module in the order the module is connected. B7A Master li k modules link d l AS-Interface master as e module odu e CompoBus/S master as e modules d l Safety relay module A--168 Programmable Controller This setting will influence the maximum number of AS-Interface slaves that can be addressed ca add essed by the e PLC. C Depending on the module, each CompoBus/S master module is allocated input and output pu words o ds a d ou pu words. o ds CQM1H J INPUT SPECIFICATIONS All of the Input Modules listed in the following tables have photocoupler isolation and LED input indicators. CPUs Number of be o i inputs Input voltage o age 16 pts 24 VDC +10%/ 15% Input impedped ance Operating voltage Response times (See Note) ON voltage OFF voltage ON delay OFF delay 10 mA for IN04/05 2.2 kΩ for IN04/05 17.4 VDC min. 5.0 VDC max. 8 ms max. 8 ms max. 6 mA for the rest (24 VDC) 3.9 kΩ for the rest Input current e External connecco ec tion i Inputs/ common co o Current consumpco su p tion i (5 VDC) Weight Terminal block 16 — — Note: Selectable from 1 to 128 ms in the PLC Setup. DC Input Modules Input p i impedance d Operating voltage Response times (See Note) ON voltage OFF voltage ON delay OFF delay 10 mA (24 VDC) 2.4 kΩ 10.2 VDC min. 3.0 VDC max. 8 ms max. 8 ms max. 12 VDC +10%/15% 6 mA (12 VDC) 1.8 kΩ 8.0 VDC min. 3.0 VDC max. 8 ms max. 8 ms max. 16 pts 24 VDC +10%/15% 6 mA (24 VDC) 3.9 kΩ 14.4 VDC min. 5.0 VDC max. 8 ms max. 8 ms max. CQM1-ID112 32 pts 12 VDC +10%/15% 4 mA (12 VDC) 2.2 kΩ 8.0 VDC min. 3.0 VDC max. 8 ms max. 8 ms max. CQM1-ID213 32 pts 24 VDC +10%/15% 4 mA (24 VDC) 5.6 kΩ 14.4 VDC min. 5.0 VDC max. 8 ms max. 8 ms max. Model Number off iinputs t Input p voltage g CQM1-ID211 8 pts 12 to 24 VDC +10%/15% CQM1-ID111 16 pts CQM1-ID212 Input p current Note: Selectable from 1 to 128 ms in the PLC Setup. Model CQM1-ID211 Number of inputs 8 pts External connection Inputs/common 8 independent commons Current consumption (5 VDC) 50 mA max. Terminal block CQM1-ID111 16 pts 16 85 mA max. 180 g max. CQM1-ID212 16 pts 16 85 mA max. 180 g max. CQM1-ID112 32 pts 32 170 mA max. 160 g max. CQM1-ID213 32 pts 32 170 mA max. 160 g max. CQM1-ID214 32 pts 32 170 mA max. 160 g max. Connector Weight 180 g max. AC Input Modules Model Input p i impedance d Operating voltage Response times ON voltage OFF voltage ON delay OFF delay 5 mA (100 VAC) 20 kΩ (50 Hz) 17 kΩ (60 Hz) 60 VAC min. 20 VAC max. 35 ms max. 55 ms max. 6 mA (200 VAC) 38 kΩ (50 Hz) 32 kΩ (60 Hz) 150 VAC min. 40 VAC max. 35 ms max. 55 ms max. Number off iinputs t Input p voltage g Input p current CQM1-IA121 8 pts 100 to 120 VAC +10%/15% CQM1-IA221 8 pts 200 to 240 VAC +10%/15% Model External connection Inputs/common Current consumption (5 VDC) Weight CQM1-IA121 Number of inputs 8 pts Terminal block 8 50 mA max. 210 g max. CQM1-IA221 8 pts 8 50 mA max. 210 g max. Programmable Controller CQM1H A--169 J INPUT CIRCUIT CONFIGURATION CPU Inputs CQM1-ID211 Input LED 3.9 kΩ (2.2 kΩ) Input LED 2.2 kΩ Internal Circuits 560 Ω CQM1-ID111/212 Internal Circuits 560 Ω CQM1-ID112/213/214 Input LED Internal Circuits ID111: ID212: Input LED R1: 1.8 kΩ R2: 620 Ω R1: 3.9 kΩ R2: 560 Ω Input LED ID112: ID213: ID214: CQM1-IA121 CQM1-IA221 Input LED Input LED 820 Ω 220 kΩ 470 Ω 68 kΩ Internal Circuits Internal Circuits 0.15 µF 2.7 kΩ A--170 R1: 750 Ω R2: 2.2 kΩ R1: 620 Ω R2: 5.6 kΩ R1: 620 Ω R2: 3.9 kΩ Programmable Controller 0.082 µF 8.2 kΩ CQM1H J OUTPUT MODULE SPECIFICATIONS All of the Output Modules have LED output indicators. Contact Output Modules Min. switching g capacity it Response times ON delay OFF delay 2 A, 250 VAC (cosφ= 1) 2 A, 250 VAC (cosφ= 0.4) 2 A, 24 VDC (16 A/Unit) 10 mA, 5 VDC 10 ms max. 5 ms max. 16 pts 2 A, 250 VAC (cosφ= 1) 2 A, 250 VAC (cosφ= 0.4) 2 A, 24 VDC (8 A/Unit) 10 mA, 5 VDC 10 ms max. 5 ms max. CQM1-OC224 8 pts 2 A, 250 VAC (cosφ= 1) 2 A, 250 VAC (cosφ= 0.4) 2 A, 24 VDC (16 A/Unit) 10 mA, 5 VDC 15 ms max. 5 ms max. Model Number of outputs Outputs/common Fuses External power supply capacity Internal current consumption (5 VDC) Weight CQM1-OC221 8 pts Independent commons None — 430 mA max. 200 g max. CQM1-OC222 16 pts 16 pts to one common — 850 mA max. 230 g max. CQM1-OC224 8 pts Independent commons — 440 mA max. 270 g max. Model Number of outputs t t Max. switching g capacity p y CQM1-OC221 8 pts CQM1-OC222 External connector t Leakage g currentt Terminal block — Transistor Output Modules Number of outputs t t Max. switching g capacity it Min. switchi capacity ing it Response times ON delay OFF delay External connector t Leakage g currentt CQM1-OD211 (NPN, sinking) 8 pts 2 A at 24 VDC +10%/ --15% 5 A/Unit — 0.1 ms max. 0.3 ms max. Terminal block 0.1 mA max. CQM1-OD212 (NPN, sinking) 16 pts 50 mA at 4.5 VDC to 300 mA at 26.4 V — 0.1 ms max. 0.4 ms max. CQM1-OD213 (NPN, sinking) 32 pts 16 mA at 4.5 VDC to 100 mA at 26.4 V — 0.1 ms max. 0.4 ms max. Connector 0.1 mA max. CQM1-OD214 (PNP, sourcing) 16 pts 50 mA at 4.5 VDC to 300 mA at 26.4 V — 0.1 ms max. 0.4 ms max. Terminal block 0.1 mA max. CQM1-OD215 (PNP, sourcing) 8 pts 1.0 A at 24 VDC +10%/ --15% 4 A/Unit — 0.2 ms max. 0.8 ms max. CQM1-OD216 (PNP, sourcing) 32 pts 0.5 A at 24 VDC +10%/ --15% 5 A/Unit — 0.1 ms max. 0.3 ms max. Model Number of outputs 8 pts Outputs/ common 8 Fuses (See Note) 7A (one fuse/common) External power supply capacity 24 VDC +10%/--15% 15 mA min. Internal current consumption (5 VDC) 90 mA max. Weight CQM1-OD212 (NPN, sinking) 16 pts 16 5A (one fuse/common) 5 to 24 VDC ±10% 40 mA min. 170 mA max. 180 g max. CQM1-OD213 (NPN, sinking) 32 pts 32 3.5 A (one fuse/common) 5 to 24 VDC ±10% 110 mA min. 240 mA max. 180 g max. CQM1-OD214 (PNP, sourcing) 16 pts 16 3.5 A (two fuses/common) 5 to 24 VDC ±10% 60 mA min. 170 mA max. 210 g max. CQM1-OD215 (PNP, sourcing) 8 pts 8 Short-circuit protection function 24 VDC +10%/--15% 24 mA min. 110 mA max. 240 g max. CQM1-OD216 (PNP, sourcing) 32 pts 32 7A (one fuse/common) 24 VDC +10%/--15% 160 mA min. 240 mA max. 210 g max. Model CQM1-OD211 (NPN, sinking) 0.1 mA max. 0.1 mA max. Connector 0.1 mA max. 200 g max. Note: Fuses are not user-serviceable. Programmable Controller CQM1H A--171 AC Output Modules Number of outputs t t Max. switching g capacity it Min. switching g capacity it Response times ON delay OFF delay External connector t Leakage g currentt CQM1-OA221 8 pts 0.4 A at 100 to 240 VAC — 6 ms max. 1/2 cycle + 5 ms max. Terminal block b oc CQM1-OA222 6 pts 0.4 A at 100 to 240 VAC 100 mA at 10 VAC 50 mA at 24 VAC 10 mA at 100 VAC 10 mA at 240 VAC 1 ms max. Load frequency of 1/2 cycle + 1 ms max. 1 mA max. at 100 00 VAC, C, A max. at 2 mA 200 VAC Model Outputs/common CQM1-OA221 Number of outputs 8 pts CQM1-OA222 6 pts Model External power supply capacity — Internal current consumption (5 VDC) 110 mA max. Weight 4 each (2 circuits) Fuses (See note) 2A (one fuse/common) 4 and 2 (2 circuits) 5A (one fuse/common) — 250 mA max. 240 g max. 240 g max. Note: Fuses are not user-serviceable. J OUTPUT CIRCUIT CONFIGURATION CQM1-OC221 CQM1-OC222 Output LED Output LED Internal Circuits Internal Circuits CQM1-OD211 CQM1-OC224 Output LED Output LED Internal Circuits Internal Circuits Maximum 250 VAC: 2 A 24 VDC: 2 A Fuse 7 A CQM1-OD212 CQM1-OD214 Output LED Output LED Internal Circuits Internal Circuits Fuse 5A (Output Circuit Configuration continues on the next page.) A--172 Programmable Controller CQM1H Fuse 3.5 A Fuse 3.5 A CQM1-OD213 CQM1-OA221 Output LED Output LED Internal Circuits Fuse 2 A Internal Circuits Fuse 2 A Output LED Fuse 3.5 A CQM1-OD215 CQM1-OA222 Output LED Internal Circuits Overcurrent detection circuit Output LED Alarm output LED Internal Circuits Fuse 5A Alarm output 3.3 kΩ Reset input 560 Ω Fuse 5A CQM1-OD216 Fuse 7 A Internal Circuits Short-circuit protection circuit Output LED (Alarm output) Short-circuit protection circuit Output LED Programmable Controller CQM1H A--173