D2MC-5F1

SUBMINIATURE Basic Switch D2MC Low Torque Basic Switch Highly reliable rotary-action switch for low torque operation ■ 0.5 A rated type (D2MC-01■ ■ ) employs crossbar alloy contacts which exhibit unsurpassed contact reliability in very small load ranges ■ High-capacity 5 A type (D2MC-5■ ■ ) employs silver contacts ■ Long life (10,000,000 mechanical operations min.) through use of a movable coil spring nt s. co m ■ ne Ordering Information Counterclockwise D2MC-5EL D2MC-5FL 10.2 g-cm 5.1 g-cm 7.6 g-cm 10.2 g-cm D2MC-5H D2MC-01E D2MC-01F D2MC-01H D2MC-5HL D2MC-01EL D2MC-01FL D2MC-01HL po Operating Torque 5.1 g-cm 7.6 g-cm Part Number Direction of actuator Clockwise D2MC-5E D2MC-5F Rated Current 5A lin e co 0.5 A m Terminal Quick connect #205 Note: 1. All the types listed are supplied without actuator lever. If an actuator lever is required, please order separately by indicating the type name of the actuator lever. See “Accessories.” on 2. The above switches accept the one-touch snap-in actuator. If retainer mounting is desired, contact OMRON for the appropriate information. ■ CONTACT FORM Specifications Model D2MC-5■ ■ D2MC-01■ ■ Electrical ratings 5 A, 125/250 VAC (resistive load) 0.5 A, 125 VAC/30 VDC (resistive load) inrush current NC: 15 A, NO: 7A 0.5 A D2MC D2MC Characteristics D2MC-5■ ■ Vibration Shock Malfunction durability Mechanical durability Malfunction durability Ambient temperature Humidity Service life (at rated OT value) Operating D2MC-01■ ■ 240 operations per minute 240 operations per minute 20 operations per minute 60 operations per minute 20 mΩ max. (initial) 100 mΩ max. (initial) 100 mΩ max. (at 500 VDC) 600 VAC, 50/60 Hz for 1 minute between nonconnected terminals 1,500 VAC, 50/60 Hz for 1 minute between current-carrying part and ground and between noncurrent-carrying part and terminal 10 to 55 Hz, 1.5 mm double amplitude 1,000 m/s2 (approx. 100 g) D2MC-■ ■ E: 100 m/s2 (approx. 10 g) D2MC-■ ■ F: 100 m/s2 (approx. 10 g) D2MC-■ ■ H: 200 m/s2 (approx. 20 g) -25° to 80°C 85% RH max. 10,000,000 operations min. 100,000 operations min. 100,000 operations min. (1,000,000 operations at 0.1A, 125 VAC/30VDC) Approx. 10.5 g m 1 to 360°/second Mechanical Electrical co Operating Speed Operating frequency Contact resistance Insulation resistance Dielectric strength nt s. Mechanical Electrical Weight ne Note: Data shown are of initial value. Electrical service life (p.f. = 1) on lin e co Service life (x 103 operations) m Mechanical service life Service life (x 103 operations) po ■ CHARACTERISTIC DATA OT (°) Rated operating current (A) ■ APPROVALS UL (File No. E41515) / CSA (File No. LR21642) Type D2MC-5■ ■ Series D2MC-01■ ■ Series Rating 5 A, 125 VAC/250 VAC 0.5 A, 125 VAC/30 VDC Note: The rated values approved by each of the safety standards (e.g. UL, CSA) may be different from the performance characteristics individually defined in this catalog. 2 D2MC D2MC Dimensions Unit: mm (inch) Counterclockwise type D2MC-■ ■F 7.6 g-cm 0.9 g-cm 21° 17° 3° 5° 38° 15 ± 3° m D2MC-■ ■E 5.1 g-cm 0.6 g-cm 21° 17° 3° 5° 38° 15 ± 3° nt #205 series quick connect terminals (0.8 t) co Operating characteristics OT max. RT min. PT max. OT min. MD min. RT min. TT min. FP Mounting holes s. Snap-on mounting Clockwise type D2MC-■ ■H 10.2 g-cm 1.3 g-cm 21° 17° 3° 5° 38° 15 ± 3° ne Note: Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.. po Accessories m (Order separately) co ■ ACTUATOR LEVER lin e Model CAA1M for snap-on mounting on In addition to the standard wire lever type shown here, various other levers are available upon request. ■ DESIGNING YOUR OWN ACTUATOR LEVER If you decide to make your own actuator lever, the materials used should be stainless steel, piano wire, hard aluminum wire, etc. There are no restrictions on the tip shape or length of the actuator lever. However, if the lever is too long, improper switch resetting or contact chattering may occur. Therefore, the shape of the lever as shown below is suitable. ■ MOUNTING ACTUATOR LEVER 1. Insert the end of the actuator lever into the hole in the rotary disc. x The appropriate value of dimension (x) from the fulcrum is 50 mm. ■ MICROVOLTAGE/-CURRENT LOAD TYPE 2. Push the lever down in the direction of the groove in the rotary disc. For details, refer to “General Information.” 3 D2MC D2MC Precautions ■ MOUNTING/SOLDERING When mounting the switch with screws, use M3 screws with plane washers or spring washers. Tighten the screws at a torque of 3 kg-cm. To solder the lead to the terminal, apply a soldering iron rated at 60 W max. quickly (within 5 seconds) with the actuator at the free position. Note that applying a soldering iron for too long a time or using one that is rated at more than 60 W may degrade the switch characteristics. on lin e co m po ne nt s. co m Do not change the operating position by modifying the actuator. OMRON ELECTRONICS, INC. OMRON CANADA, INC. One East Commerce Drive Schaumburg, IL 60173 885 Milner Avenue Scarborough, Ontario M1B 5V8 1-800-55-OMRON 416-286-6465 Cat. No. GC SW5 4 4/98 Specifications subject to change without notice. Printed in the U.S.A.