D2SW-P2L1T

Sealed Subminiature Basic Switch D2SW-P Sealed Basic Switch with Simplified Construction, Mounting Compatible with SS and D2SW Series. • Sealed to IEC IP67. • Switch rating of 2A at 250 VAC possible with a single-leaf movable spring. Models for micro loads are also available. • Solder, quick-connect terminals (#110), PCB terminals and molded lead wires are available. Even-pitched PCB terminals are also standardized. Ordering Information Rating Actuator 2A 0.1A Terminal Solder terminals Quick-connect terminals (#110) PCB terminals Uneven pitch Even pitch Molded lead wires Pin plunger D2SW-P2H D2SW-P2T D2SW-P2D D2SW-P2B D2SW-P2M Hinge lever D2SW-P2L1H D2SW-P2L1T D2SW-P2L1D D2SW-P2L1B D2SW-P2L1M Hinge roller lever D2SW-P2L2H D2SW-P2L2T D2SW-P2L2D D2SW-P2L2B D2SW-P2L2M Simulated roller lever D2SW-P2L3H D2SW-P2L3T D2SW-P2L3D D2SW-P2L3B D2SW-P2L3M Pin plunger D2SW-P01H D2SW-P01T D2SW-P01D D2SW-P01B D2SW-P01M Hinge lever D2SW-P01L1H D2SW-P01L1T D2SW-P01L1D D2SW-P01L1B D2SW-P01L1M Hinge roller lever D2SW-P01L2H D2SW-P01L2T D2SW-P01L2D D2SW-P01L2B D2SW-P01L2M Simulated roller lever D2SW-P01L3H D2SW-P01L3T D2SW-P01L3D D2SW-P01L3B D2SW-P01L3M Note: Consult your OMRON sales representative for details on SPST-NO and SPST-NC models. Model Number Legend D2SW-P 1 2 3 4 1. Ratings 2: 2 A at 250 VAC 01: 0.1 A at 30 VDC 2. Actuator None: Pin plunger L1: Hinge lever L2: Hinge roller lever L3: Simulated roller lever 3. Contact Form None: SPDT -2: SPST-NC* -3: SPST-NO* *Lead wire versions only 4. Terminals H: T: D: B: M: Sealed Subminiature Basic Switch Solder terminals Quick-connect terminals (#110) PCB terminals (Uneven pitch) PCB terminals (even pitch) Molded lead wires D2SW-P 201 Specifications ■ Characteristics Item Model D2SW-P2 D2SW-P01 Operating speed 0.1 mm to 500 mm/s (pin plunger models) Operating frequency Mechanical: 120 operations/min max. Electrical: 20 operations/min max. Insulation resistance 100 MΩ min. (at 500 VDC) Contact resistance Terminal models: 50 mΩ max. Molded lead wire models: 100 mΩ max. Terminal models: 100 mΩ max. Molded lead wire models: 150 mΩ max. Dielectric strength (see note 2) 1,000 VAC, 50/60 Hz for 1 min. between terminals of the same polarities 600 VAC, 50/60 Hz for 1 min. between terminals of the same polarities 1,500 VAC, 50/60 Hz for 1 min. between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts Vibration resistance (see note 3) Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Shock resistance (see note 3) Destruction: 1,000 m/s2 (approx. 100 G) max. Malfunction: 300 m/s2 (approx. 30 G) max. Degree of protection IEC IP67 (excluding the terminals on terminal models) Degree of protection against electric shock Class I Proof tracking index (PTI) 175 Ambient operating temperature -20°C to 70°C (at 60% RH max.) with no icing Ambient operating humidity 85% max. (for 5°C to 35°C) Life expectancy Mechanical: 1,000,000 operations min. (60 operations/min.) Electrical: 50,000 operations min. (20 operations/min.) Weight Approx. 2 g (pin plunger models with terminals) Mechanical: 1,000,000 operations min. (60 operations/min.) Electrical: 200,000 operations min. (20 operations/min.) Note: 1. The data given above are initial values. 2. The dielectric strength shown is measured using a separator between the switch and metal mounting plate. 3. For the pin plunger models, the above values apply for both the free position and total travel position. For the lever models, the values apply at the total travel position. Contact opening or closing time is within 1ms. ■ Ratings ■ Contact Specifications Model Rated voltage Resistive load Item D2SW-P2 D2SW-P01 D2SW-P2 30 VDC 2A Specification Rivet Crossbar Material Silver alloy Gold alloy Gap (standard value) 0.5 mm 250 VAC D2SW-P01 30 VDC 0.1 A 125 VAC Minimum applicable load 160 mA at 5 VDC 1 mA at 5 VDC (see note) Note: The ratings values apply under the following test conditions. Ambient temperature: 20±2°C Ambient humidity: 65±5% Operating frequency: 20 operations/min. ■ Approved Standards Note: Minimum applicable loads are indicated by N standard reference values. This value represents the failure rate at a 60% (λ60) reliability level (JIS C5003). The equation λ60=0.5 x 10-6 / operations indicates that a failure rate of 1/2,000,000 operations can be expected at a reliability level of 60% Consult your OMRON sales representative for specific models with standard approvals. ■ Contact Form UL Recognized CSA Certified SPDT Rated voltage D2SW-P2 D2SW-P01 125 VAC 250 VAC — 2A 0.1 A — 30 VDC 2A 0.1 A COM NO NC (Black) (Blue) (Red) SPST-NC SPST-NO (wire models, only) (wire models, only) COM (Black) NC (Red) COM NO (Black) (Blue) Note: Lead wire colors are indicated in parentheses. 202 Sealed Subminiature Basic Switch D2SW-P Dimensions ■ Terminals Note: 1. All units are in millimeters unless otherwise indicated. 2. Terminal plate thickness is 0.5 mm for all models. Solder Terminals C Quick-connect Terminals (#110) NC NC 3.3±0.1 7.3 3.3±0.1 11 Three, 1.6-dia. Holes 3.2 2.15 0.5 8.55 7.1 0.5 3-2.8 6.4±0.2 15.5 7.6±0.2 6.4±0.2 7.6±0.2 5.15 9.5±0.1 19.8±0.2 5.15 9.5±0.1 19.8±0.2 PCB Terminals (Even pitch) PCB Terminals (Uneven pitch) 1.8 3.3±0.1 1.8 3.3±0.1 3.9 3.9 1.85 3-1.2 3-0.8 8.8±0.2 0.5 16.1±0.2 6.4±0.2 5.15 9.5±0.1 19.8±0.2 PCB Mounting Dimensions (Reference) 16.1±0.1 8.8±0.1 3-1.2 3-0.8 1.3 1.3 5.15 9.5±0.1 7.62±0.2 7.62±0.2 19.8±0.2 0.5 6.4±0.2 PCB Mounting Dimensions (Reference) 7.62±0.1 7.62±0.1 Three, 1.35 to 1.5 dia. Three,-1.35 to 1.5 dia. Molded Lead Wires 9.2 6.4±0.2 300±10 Normally closed terminal (red) Common terminal (black) Insulator Stranded annealed copper wites 0.7 (5) 5.15 9.5±0.1 Normally open terminal (blue) 21.2 ■ Mounting Holes All switches may be panel mounted using M2.3 mounting screws with plane washers or spring washers to securely mount the switch. Tighten the screws to a torque of 0.23 to 0.26 N·m Exceeding the specified torque may result in deterioration of the sealing or damage. Two, M2.3 screw hole 9.5±0.1 Sealed Subminiature Basic Switch D2SW-P 203 ■ Dimensions and Operating Characteristics Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following illustrations and drawings are for solder terminal models. Refer to Terminals section for details on models with quick-connect terminals (#110) or PCB terminals or molded lead wires. 3. The operating characteristics are for operation in the A direction ( ). . Pin Plunger Models D2SW-P2@@ D2SW-P01@@ 7.55±0.2 A PT 1.8 dia. 2.5±0.07 dia. 2.35 +0.075 −0.05 dia. OP 6.9 7.7 2.35+0.075 −0.05 3.3±0.1 7.3 3.2 2.15 Three, 1.6 dia. holes 8.55 15.5 0.5 OF max. RF min. 183 gf 20 gf PT max. OT min. MD max. 0.6 mm 0.4 mm 0.15 mm OP 8.4±0.3 mm 6.4±0.2 5.15 9.5±0.1 19.8±0.2 Hinge Lever Models D2SW-P2L1@@ D2SW-P01L1@@ A t=0.3 Stainless-steel lever 14.5±0.6 2.35 +0.075 −0.05 dia. 2.5±0.07 dia. OP FP 6.9 7.7 2.35 +0.075 −0.05 3.3±0.1 7.3 3.2 2.15 Three, 1.6 dia. holes 8.55 15.5 5.15 9.5±0.1 19.8±0.2 OF max. RF min. 61 gf 5 gf OT min. MD max. 0.8 mm 0.8 mm FP max. OP 13.6 mm 8.8±0.8 mm OF max. RF min. 61 gf 5 gf OT min. MD max. 0.8 mm 0.8 mm FP max. OP 19.3 mm 14.5±0.8 mm OF max. RF min. 61 gf 5 gf OT min. MD max. 0.8 mm 0.8 mm FP max. OP 15.5 mm 10.7±0.8 mm 0.5 6.4±0.2 Hinge Roller Lever Models dia. 4.8 x 3.2 Polyacetal resin roller A D2SW-P2L2@@ D2SW-P01L2@@ t=0.3 Stainless-steel lever 14.5±0.6 2.5±0.07 dia. 2.35 +0.075 -0.05 dia. FP OP 6.9 7.7 2.35 +0.075 -0.05 3.3±0.1 7.3 3.2 2.15 Three, 1.6 dia. holes 8.55 15.5 5.15 9.5±0.1 19.8±0.2 0.5 6.4±0.2 Simulated Roller Lever Models D2SW-P2L3@@ D2SW-P01L3@@ A t=0.3 Stainless-steel lever 15.8±0.6 R1.3 2.35 +0.075 −0.05 dia. 2.5±0.07 dia. 6.9 7.7 2.35 +0.075 −0.05 3.3±0.1 7.3 3.2 2.15 204 OP FP 8.55 15.5 5.15 9.5±0.1 19.8±0.2 Sealed Subminiature Basic Switch Three, 1.6 dia. holes 0.5 6.4±0.2 D2SW-P Precautions Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide, “Snap Action Switches, Technical Information” for correct use. ■ Correct Use Mounting Operating Stroke Setting Turn OFF the power supply before mounting or removing the Switch, wiring, or performing maintenance or inspection. Failure to do so may result in electric shock or burning. Set the operating stroke so that the actuator is completely disengaged when the switch is in the free position (FP), and is pushed to a point between 60% and 90% of the OT distance after the switch is operated. Mount the Switch onto a flat surface. Mounting on an uneven surface may cause deformation of the Switch, resulting in faulty operation or damage. Insufficient or excessive pushing of the actuator may result in decreased switch durability or damage to the switch. Using Micro Loads Use an operating body with low frictional resistance and of a shape that will not interfere with the sealing rubber, otherwise the plunger may be damaged or the sealing may deteriorate. Using a model for ordinary loads to switch microloads may result in faulty operation. Instead, use the models that are designed for microloads and that operate in the following range; With the pin plunger models, set the Switch so that the plunger can be pushed in from directly above. Since the plunger is covered with a rubber cap, applying a force from lateral directions may cause damage to the plunger or reduction in the sealing capability Voltage (V) Operating Body 30 0.16mA 26mA 100mA 24 . Correct Incorrect Incorrect Operating range for micro load models D2SW-P01 Operating range for general-load models D2SW-P2 12 5 Inoperable range 1mA Handling Do not handle the Switch in a way that may cause damage to the sealing rubber. When handling the Switch, ensure that uneven pressure or, as shown in the following diagram, pressure in a direction other than the operating direction is not applied to the Actuator, otherwise the Actuator or Switch may be damaged, or durability may be decreased. 100mA 160mA 0 0.1 1 10 100 1,000 Current (mA) However, even when using microload models within the operating range shown above, if inrush current or inductive voltage spikes occur when the contact is opened or closed, then contact wear may increase and so decrease the service life. Therefore, insert a contact protection circuit where necessary. Wiring Molded Lead Wire Models When wiring molded lead wire models, ensure that there is no weight on the wire or that there are no sharp bends near the parts where the wire is drawn out. Otherwise, damage to the Switch or deterioration in the sealing may result. Sealed Subminiature Basic Switch D2SW-P 205 ■ Cautions Degree of Protection Connecting to Terminals Do not use this product in water. Although these models satisfy the test conditions for the standard given below, this test is to check the ingress of water into the switch enclosure after submerging the Switch in water for a given time. Satisfying this test condition does not mean that the Switch can be used in water. IEC 60529: 2001 Degrees of protection provided by enclosures (IP Code) Code: IP67 (The test to meet the standard checks for water intrusion after immersion for 30 minutes.) Do not operate the Switch when it is exposed to water spray, or when water drops adhere to the Switch surface, or during sudden temperature changes, otherwise water may intrude into the interior of the Switch due to a suction effect. Prevent the Switch from coming into contact with oil and chemicals. Otherwise, damage to or deterioration of Switch materials may result. Connecting to Solder Terminals When soldering the lead wire to the terminal, first insert the lead wire conductor through the terminal hole and the conduct soldering. Make sure that the temperature at the tip of the soldering iron is 350 to 400°C. Do not take more than 3 seconds to solder the switch terminal, and do not impose external force on the terminal for 1 min. after soldering. Improper soldering involving an excessively high temperature or excessive soldering time may deteriorate the characteristics of the Switch. Connecting to Quick-connect Terminals Wire the quick-connect terminals (#110) with receptacles. Insert the terminals straight into the receptacles. Do not impose excessive force on the terminal in the horizontal direction, otherwise the terminal may be deformed or the housing may be damaged. Connecting to PCB Terminal Boards Do not use the Switch in areas where it is exposed to silicon adhesives, oil, or grease, otherwise faulty contact may result due to the generation of silicon oxide. When using automatic soldering baths, we recommend soldering at 260±5°C within 5 seconds. Make sure that the liquid surface of the solder does not flow over the edge of the board. The environment-resistant performance of the switch differs depending on operating loads, ambient atmospheres, and installation conditions, etc. Please perform an operating test of the switch in advance under actual usage conditions. When soldering by hand, as a guideline, solder with a soldering iron with a tip temperature of 350 to 400°C within 3 seconds, and do not apply any external force for at least 1 minute after soldering. When applying solder, keep the solder away from the case of the Switch and do not allow solder or flux to enter the case. Side-actuated (Cam/Dog) Operation When using a cam or dog to operate the Switch, factors such as the operating speed, operating frequency, push-button indentation, and material and shape of the cam or dog will affect the durability of the Switch. Confirm performance specifications under actual operation conditions before using the Switch in applications. 206 Sealed Subminiature Basic Switch D2SW-P MEMO Sealed Subminiature Basic Switch D2SW-P All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ON-LINE OMRON ELECTRONIC COMPONENTS LLC Global - http://www.omron.com USA - http://www.components.omron.com 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 847-882-2288 Cat. No. X303-E-1 11/10 Specifications subject to change without notice Sealed Subminiature Basic Switch D2SW-P Printed in USA