D2VW-5-1

D2VW Sealed Miniature Basic Switch Sealed Miniature Basic Switch Conforms to IP67 (Molded Lead Wire Type Only) Use of epoxy resin assures stable sealing, making this switch ideal for places subject to water spray or excessive dust. V-series internal mechanism assures high precision and long life. Ideal for automobiles, agricultural machines, large-scale home appliances, and industrial equipment, which require high environmental resistance. Models available with conformance to safety standards, including UL, CSA and VDE. WRC Ordering Information Model Number Legend D2VW-jj-jj 1 2 3 4 1. Ratings 5: 5 A at 250 VAC 01: 0.1 A at 30 VDC 2. Actuator None: Pin plunger L1A: Short hinge lever L1: Hinge lever L1B: Long hinge lever L3: Simulated roller lever L2A: Short hinge roller lever L2: Hinge roller lever 3. Contact Form 1: SPDT 2: SPST-NC 3: SPST-NO 4. Terminals None, HS: Solder terminals (HS for UL and CSA approval.) M, MS: Molded lead wires (MS for UL and CSA approval) List of Models Actuator Pin plunger p g Short hinge g lever Hinge g Lever Long g hinge g lever Simulated roller lever Short hinge g roller lever Hinge roller lever Note: Model 5A 0.1 A Solder terminals D2VW-5-1 D2VW-01-1 Molded lead wires D2VW-5-1M D2VW-01-1M Solder terminals D2VW-5L1A-1 D2VW-01L1A-1 Molded lead wires D2VW-5L1A-1M D2VW-01L1A-1M Solder terminals D2VW-5L1-1 D2VW-01L1-1 Molded lead wires D2VW-5L1-1M D2VW-01L1-1M Solder terminals D2VW-5L1B-1 D2VW-01L1B-1 Molded lead wires D2VW-5L1B-1M D2VW-01L1B-1M Solder terminals D2VW-5L3-1 D2VW-01L3-1 Molded lead wires D2VW-5L3-1M D2VW-01L3-1M Solder terminals D2VW-5L2A-1 D2VW-01L2A-1 Molded lead wires D2VW-5L2A-1M D2VW-01L2A-1M Solder terminals D2VW-5L2-1 D2VW-01L2-1 Molded lead wires D2VW-5L2-1M D2VW-01L2-1M 1. The standard lengths of the molded lead wires (AV0.75f) of models incorporating them are 30 cm. 2. Consult your OMRON sales representative for details on SPST-NO and SPST-NC models. 3. Add “HS” or “MS” to the end of the model number for the UL/CSA-approved version (e.g., D2VW-01-1 → D2VW-01-1HS). Consult your OMRON sales representative for details. 214 D2VW D2VW Specifications Ratings Item Model D2VW-5 D2VW-01 Note: Resisteve load Rated voltage 250 VAC 5A 125 VAC 5A 30 VDC 5A 125 VAC 0.1 A 30 VDC 0.1 A The ratings values apply under the following test conditions: Ambient temperature: 20±2°C Ambient humidity: 65±5% Operating frequency: 30 operations/min Switching Capacity per Load (Reference Values) Non-inductive load Resistive load Model D2VW-5 Note: Voltage NC Inductive load Lamp load NO NC Inductive load NO NC 125 VAC 5A 0.5 A 4A 250 VAC 5A 0.5 A 4A 30 VDC 5A 3A 4A 125 VDC 0.4 A 0.1 A 0.4 A NO 1. The above current ratings are the values of the steady-state current. 2. Inductive load has a power factor of 0.7 min. (AC) and a time constant of 7 ms max. (DC). 3. Lamp load has an inrush current of 10 times the steady-state current. Characteristics Operating speed 0.1 mm to 1 m/s (pin plunger models) Operating frequency Mechanical: 300 operations/min max. Electrical: 30 operations/min max. Insulation resistance 100 MΩ min. (at 500 VDC) Contact resistance (initial value) 50 mΩ max. (100 mΩ max. for molded lead wire models) Dielectric strength (see note 2) 1,000 VAC, 50/60 Hz for 1 min between terminals of same polarity 1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground 1,500 VAC, 50/60 Hz for 1 min between each terminal and non-current-carrying metal parts Vibration resistance (see note 3) Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Shock resistance (see note 3) Destruction: 1,000 m/s2 {approx. 100G} max. Malfunction: 300 m/s2 {approx. 30G} max. Durability (see note 4) Mechanical: 10,000,000 operations min. (60 operations/min) Electrical: D2VW-5 models: 100,000 operations min. (30 operations/min) D2VW-01 models: 1,000,000 operations min. (30 operations/min) Degree of protection IEC IP67 (excluding the terminals on terminal models) Degree of protection against electric shock Class I Proof tracking index (PTI) 175 Ambient operating temperature (see note 5) –40°C to 85°C (at ambient humidity of 60% max.) (with no icing) Ambient operating humidity 95% max. (for 5°C to 35_C) Weight Approx. 7 g (pin plunger models with terminals) Note: 1. The data given above are initial values. 2. The dielectric strength shown in the table indicates the value for models with a Separator. 3. For the pin plunger models, the above values apply for use at both the free position and total travel position. For the lever models, they apply at the total travel position. 4. For testing conditions, consult your OMRON sales representative. 5. The operating temperature of the lead wire (AV0.75f) for the molded lead wire model is between –40°C to 85°C. 215 D2VW D2VW Approved Standards Contact Specifications Consult your OMRON sales representative for specific models with standard approvals. Item Contact UL1054 (File No. E41515)/ CSA C22.2 No.55 (File No. LR21642) Rated voltage D2VW-5 3A 3A 0.1 A --- 30 VDC --- 0.1 A Rated voltage D2VW-5 125 VAC 250 VAC Crossbar Material Silver alloy Gold alloy Gap (standard value) 0.5 mm NC 15 A max. --- NO 15 A max. --- Minimum applicable load (see note) 160 mA at 5 VDC 1 mA at 5 VDC Inrush currentt EN61058-1 (File No. 104068, VDE approval) D2VW-01 --3A D2VW-01 Rivet D2VW-01 125 VAC 250 VAC D2VW-5 Specification Note: For more information on the minimum applicable load, refer to Using Micro Loads on page 219. 0.1 A --- Testing conditions: 25E3 (25,000 operations), T85 (0°C to 85°C) for D2VW-5, 1E5 (100,000 operations), T85 (0°C to 85°C) for D2VW-01 Contact Form SPDT SPST-NC NC (red) NO (blue) COM (black) Note: SPST-NO NC (red) NO (blue) COM (black) COM (black) Colors in parentheses indicate lead wire colors. Dimensions Note: All units are in millimeters unless otherwise indicated. Terminals The pin plunger model is shown here as a typical example. Operating characteristics and dimensions of the actuator section are the same as for the molded lead wire models. Molded Lead Wires Solder/Quick Connect Terminals 2.4 dia. hole 1.3 dia. hole AV 0.75f Lead wire (red)* 10.3 AV 0.75f Lead wire (blue)* AV 0.75f Lead wire (black)* 4.8 1.2 5.2 8.4 0.5 2.5 5.2 5.2 t=0.5 Three, solder terminals 33 41.4 Mounting Holes Two, 3.1-dia. mounting holes or M3 screw holes 10.3 ± 0.1 22.2 ± 0.1 216 33 10.3 300±10 * UL/CSA approved models have UL approved wiring. 22.2±0.1 2.8 (5) 22.2±0.1 2.8 D2VW D2VW Dimensions and Operating Characteristics Note: 1. All units are in millimeters unless otherwise indicated. 2. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. 3. The operating characteristics are for operation in the A direction ( ). Pin Plunger Models 2.4 dia. hole 1.3 dia. hole OF max. 1.96 N {{200 g gf}} RF min. 0.29 N {30 gf} PT max. 1.2 mm OT min. 1.0 mm MD max. 0.4 mm OP 14.7±0.4 mm OF max. 1.96 N {{200 g gf}} RF min. 0.20 N {20 gf} PT max. 1.6 mm OT min. 0.8 mm MD max. 0.5 mm OP 15.2±0.5 mm Hinge Lever Models OF max. 1.18 N {{120 g gf}} D2VW-01L1-1M D2VW-5L1-1M RF min. 0.15 N {15 gf} PT max. 4.0 mm OT min. 1.6 mm MD max. 0.8 mm OP 15.2±1.2 mm Long Hinge Lever Models OF max. 0.59 N {{60 g gf}} D2VW-01L1B-1M D2VW-5L1B-1M RF min. 0.05 N {5 gf} PT max. 9.0 mm OT min. 3.2 mm MD max. 2.0 mm OP 15.2±2.6 mm D2VW-01-1 D2VW-5-1 10.3 4.8 1.2 5.2 20.2±0.25 A 2.5 dia. 2.8 PT OP 8.4 +0.13 3.1 –0.03 dia. holes 0.5 15.9 10.3±0.1 2.5 5.2 5.2 3.2±0.1 dia. +0.13 3.1 –0.03 22.2±0.1 2.8 t=0.5 Three, solder terminals 33 41.4 Short Hinge Lever Models D2VW-01L1A-1M D2VW-5L1A-1M A 4.3 24.3±0.8 t=0.5* 5 PT OP 15.9 *Stainless-steel lever A 35.6±0.8 t=0.5* 10.3 4.3 5 PT OP 15.9 *Stainless-steel lever A 59.4±0.8 t=0.5* 10.3 5 4.3 PT OP 15.9 *Stainless-steel lever 10.3 217 D2VW D2VW Simulated Roller Lever Models D2VW-01L3-1M D2VW-5L3-1M A PT 32.6±0.8 3.5R t=0.5* 4.3 5 OP 15.9 D2VW-01L2A-1M D2VW-5L2A-1M 4.8 dia. 4.8 ** PT 24.3±0.8 A 20.1±0.8 5 t=0.5* 7.2 OP 15.9 *Stainless-steel lever **Oil-less polyacetal resin roller A 34±0.8 4.8 dia. 4.8 ** PT 5 7.2 t=0.5* OP 15.9 *Stainless-steel lever **Oil-less polyacetal resin roller 218 RF min. 0.15 N {15 gf} PT max. 4.0 mm OT min. 1.6 mm MD max. 0.8 mm OP 18.7±1.2 mm OF max. 2.25 N {{230 g gf}} RF min. 0.20 N {20 gf} PT max. 1.6 mm OT min. 0.8 mm MD max. 0.5 mm OP 20.7±0.6 mm OF max. 1.18 N {{120 g gf}} RF min. 0.15 N {15 gf} PT max. 4.0 mm OT min. 1.6 mm MD max. 0.8 mm OP 20.7±1.2 mm 10.3 Hinge Roller Lever Models D2VW-01L2-1M D2VW-5L2-1M 1.18 N {{120 g gf}} 10.3 *Stainless-steel lever Short Hinge Roller Lever Models OF max. 10.3 D2VW D2VW Precautions Refer to pages 26 to 31 for common precautions. Cautions Correct Use Mounting Degree of Protection Do not use the Switch underwater. The Switch was tested and found to meet the conditions necessary to meet the following standard. The test checks for water intrusion after immersion for a specified time period. The test does not check for switching operation underwater. IEC Publication 529, degree of protection IP67. Protection Against Chemicals Use M3 mounting screws with plane washers or spring washers to securely mount the Switch. Tighten the screws to a torque of 0.39 to 0.59 N S m {4 to 6 kgf S cm}. Operating Body With the pin plunger models, set the Switch so that the plunger can be pushed in from directly above. Since the plunger is covered with a rubber cap, applying a force from lateral directions may cause damage to the plunger or reduction in the sealing capability. Prevent the Switch from coming into contact with oil and chemicals. Otherwise, damage to or deterioration of Switch materials may result. Correct Incorrect Incorrect Handling Handle the Switch carefully so as not to break the sealing rubber of the plunger. Using Micro Loads Voltage (V) Using a model for ordinary loads to open or close the contact of a micro load circuit may result in faulty contact. Use models that operate in the following range. However, even when using micro load models within the operating range shown below, if inrush current occurs when the contact is opened or closed, it may increase contact wear and so decrease durability. Therefore, insert a contact protection circuit where necessary. The minimum applicable load is the N-level reference value. This value indicates the malfunction reference level for the reliability level of 60% (λ 60). The equation, λ 60 = 0.5 10–6/operations indicates that the estimated malfunction rate is less than 1/2,000,000 operations with a reliability level of 60%. Operating range for micro load models D2VW-01 Operating range for general-load models D2VW-05 Inoperable range Current (mA) ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. C095-E1-03C 219