Safety Limit Switch
D4B-@N
C72I-E-02
Robust safety limit switch with metal housing
Slow-action and snap-action contact with
certified direct opening operation
certification
• Direct opening mechanism (NC contacts only) added to
enable opening contacts when faults occur, such as fused
contacts.
• Safety of lever settings ensured using a mechanism that
engages a gear between the operating position indicator plate
and the lever.
• Equipped with a mechanism that indicates the applicable
operating zone, as well as push-button switching to control left
and right motion.
• Head seal structure strengthened to improve seal properties
(TÜV: IEC IP67, UL: NEMA 3, 4, 4X, 6P, and 13).
• Wide standard operating temperature range:
–40 to 80°C (standard type).
• Certified standards: UL, CSA, EN (TÜV), and CCC.
• Conforms to ISO 14119.
Note: Contact your sales representative for details on
models with safety standard certification.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Be sure to read the “Safety Precautions” on page 9.
Model Number Structure
Model Number Legend
D4B-@@@@N
1 2
3
1. Conduit size
2: G1/2 (PF1/2) (1-conduit)
4: M20 (1 conduit)
2. Built-in Switch
1: 1NC/1NO (snap-action)
5: 1NC/1NO (slow-action)
A: 2NC (slow-action)
3. Actuator
11: Roller lever (resin roller)
15: Roller lever (stainless steel roller)
16: Adjustable roller lever
17: Adjustable rod lever
70: Top plunger
71: Top roller plunger
1
D4B-@N
Ordering Information
Set Model Numbers
Consult with your OMRON representative when ordering any models that are not listed in this table.
Safety Limit Switches (with Direct Opening Mechanism)
1NC/1NO (Snap-action)
Actuator
Conduit openings
Model
Direct
opening
1NC/1NO (Slow-action)
Model
Direct
opening
2NC (Slow-action)
Model
Roller lever
(resin roller)
G1/2 (PF1/2)
D4B-2111N
D4B-2511N
D4B-2A11N
M20
D4B-4111N
D4B-4511N
D4B-4A11N
Roller lever
(stainless steel
roller)
G1/2 (PF1/2)
D4B-2115N
D4B-2515N
D4B-2A15N
M20
D4B-4115N
D4B-4515N
D4B-4A15N
G1/2 (PF1/2)
D4B-2170N
D4B-2570N
D4B-2A70N
M20
D4B-4170N
D4B-4570N
D4B-4A70N
G1/2 (PF1/2)
D4B-2171N
D4B-2571N
D4B-2A71N
M20
D4B-4171N
D4B-4571N
D4B-4A71N
Direct
opening
Top plunger
Top roller plunger
General-purpose Limit Switches
1NC/1NO (Snap-action)
Actuator
Adjustable roller
lever
Adjustable rod
lever
Conduit openings
G1/2 (PF1/2)
Model
Direct
opening
D4B-2116N
1NC/1NO (Slow-action)
Model
D4B-2516N
--M20
D4B-4116N
G1/2 (PF1/2)
D4B-2117N
D4B-4117N
2NC (Slow-action)
Model
D4B-4516N
--D4B-4A16N
D4B-2517N
D4B-2A17N
---
D4B-4517N
Direct
opening
D4B-2A16N
---
--M20
Direct
opening
--D4B-4A17N
Note: Consult your OMRON representative for products.
2
D4B-@N
Specifications
Standards and EC Directives
Conforms to the following EC Directives:
•
•
•
•
•
Machinery Directive
Low Voltage Directive
EN50041
EN60204-1
EN ISO 14119
Certified Standards
Snap-action Models
Certification body
TÜV Rheinland
Slow-action Models
Standard
EN60947-5-1
(certified direct
opening mechanism)
GS-ET-15
File No.
Certification body
Consult your
OMRON
representative for
details.
TÜV Rheinland
EN60947-5-1
(uncertified direct
J50005477 *
opening mechanism)
Standard
EN60947-5-1
(certified direct
opening mechanism)
GS-ET-15
File No.
Consult your
OMRON
representative for
details.
EN60947-5-1
(uncertified direct
J50005477 *
opening mechanism)
UL
UL508
E76675
UL
UL508
E76675
CSA
C22.2 No. 14
LR45746
CSA
C22.2 No. 14
LR45746
CQC (CCC)
GB14048.5
2003010305077612
CQC (CCC)
GB14048.5
2003010305077612
* Adjustable roller lever, adjustable rod lever only.
* Adjustable roller lever, adjustable rod lever only.
Certified Standard Ratings
TÜV (EN60947-5-1), CCC (GB14048.5)
Item
Utilization category AC-15
Rated operating current (Ie)
2A
Rated operating voltage (Ue)
400 V
Note: As protection against short-circuiting, use either a gI-type or gG-type 10 A fuse that conforms to IEC60269.
UL/CSA: (UL508, CSA C22.2 No. 14)
A600
Rated voltage
120 VAC
240 VAC
480 VAC
600 VAC
Current (A)
Carry current
10 A
Make
60
30
15
12
Volt-amperes (VA)
Break
6
3
1.5
1.2
Make
7,200
Break
720
3
D4B-@N
Ratings
Non-inductive load (A)
Rated voltage (V)
Resistive load
NC
Inductive load (A)
Lamp load
NO
NC
Inductive load
NO
NC
Motor load
NO
NC
125 VAC
250
400
10
10
10
3
2
1.5
1.5
1
0.8
10
10
3
5
3
1.5
8 VDC
14
30
125
250
10
10
6
0.8
0.4
6
6
4
0.2
0.1
3
3
3
0.2
0.1
10
10
6
0.8
0.4
6
6
4
0.2
0.1
Note: 1.
2.
3.
4.
NO
2.5
1.5
0.8
The above values are continuous currents.
Inductive loads have a power factor of 0.4 or higher (AC) or a time constant of 7 ms or lower (DC).
Lamp loads have a inrush current of 10 times the normal current.
Motor loads have a inrush current of 6 times the normal current.
Inrush current
30 A max.
Characteristics
Degree of protection *1
Durability *2
IP67 (EN60947-5-1)
Mechanical
Electrical
Operating speed
Operating frequency
30,000,000 operations min. (snap-action)
10,000,000 operations min. (slow-action)
500,000 operations min. (10 A resistive load at 250 VAC)
1 mm/s to 0.5 m/s
Mechanical
Electrical
120 operations/minute
30 operations/minute
Contact resistance
25 mΩ max.
Minimum applicable load *3
180 mA resistive load at 5 VAC
(N-level reference value)
Rated insulation voltage (Ui)
600 V (EN60947-5-1)
Rated frequency
50/60 Hz
Protection against electric shock
Class I (with ground terminal)
Pollution degree (operating environment)
3 (EN60947-5-1)
Between terminals
of same polarity
Impulse withstand voltage Between terminals
(EN60947-5-1)
of different polarity
2.5 kV (snap-action)/4 kV (slow-action)
4 kV (slow-action)
Between each
4 kV
terminal and ground
Insulation resistance
100 MΩ min. (at 500 VDC) between terminals of the same polarity and between each
terminal and non-current-carrying part
Contact gap
2 × 2 mm min. (slow-action)
2 × 0.5 mm min. (snap-action)
Vibration resistance
Shock resistance
Malfunction
10 to 55 Hz, 0.75 mm single amplitude
Destruction
1,000 m/s2 min.
Malfunction
300 m/s2 min.
Conditional short-circuit current
100 A (EN60947-5-1)
Conventional enclosed thermal current (Ithe)
20 A (EN60947-5-1)
Ambient operating temperature
–40 to 80°C (with no icing)
Ambient operating humidity
95% max.
Weight
Approx. 250 g
Note: 1. The above values are initial values.
2. The above values may vary depending on the model. Consult your OMRON sales representative for details.
*1. The degree of protection is tested using the method specified by the standard (EN60947-5-1). Confirm that sealing properties are sufficient for
the operating conditions and environment beforehand.
*2. The durability is for an ambient temperature of 5 to 35°C and ambient humidity of 40% to 70%. For further conditions, consult your OMRON
sales representative.
*3. The above values may vary depending on switching frequency, environmental condition, and relativity level, consult your OMRON sales
representative.
4
D4B-@N
Engineering Data
Electrical Durability (Snap-action)
(Ambient temperature: 5 to 30°C, ambient humidity: 40 to 70%)
(cosφ = 0.4)
1,000
500
125 VAC
Operating frequencies:
30 times/min., cosφ = 1
300
250 VAC
480 VAC
100
Operations (x 104)
Operations (x 104)
(cosφ = 1)
1,000
500
300
250 VAC
100
50
50
30
30
10
10
Switching current (A)
Operating frequencies:
30 times/min., cosφ = 0.4
500 VAC
Switching current (A)
Structure and Nomenclature
Structure
Head
Can be connected in any of four directions (except for
Roller Plunger Models, which can be connected at either
of 2 directions that differ by 90°)
The roller lever switch employs a
system which allows
selection of operation on only one
side (left or right)
or both sides without the use of
any tools.
Seal Ring
Sealing properties improved by using a X ring and
bearing-free structure.
Roller
Nylon rollers used for superior resistance to wear.
Lever (Form Lock Structure)
The lever has an operating position indication plate
and grooves that mate every 90° to prevent slipping
between the rotary axis and lever.
The operating position indicator plate
Built-in Switch
Direct opening mechanism used for NC contact to
separate contact for faults, such as contact welding.
The heights of the NC and NO terminals are different
to enable easier wiring.
Conduit Opening
G1/2 or M20
Cover
Ground Screw
Ground screws are provided on all
models for increased safety.
5
D4B-@N
Direct Opening Mechanism
1NO/1NC Contact (Snap-action)
Conforms to EN60947-5-1 Direct Opening
(Only NC contact has a direct opening mechanism.)
1. When contact welding occurs.
2. When contacts are being pulled apart.
Movable contact
Safety cam directly
pushes up the
movable contact
blade.
Movable contact
blade
B
Plunger
A
3. When contacts are completely
pulled apart.
Safety cam
Fixed contact (NC)
1NC/1NO Contact (Slow-action)
2NC Contact (Slow-action)
Conforms to EN60947-5-1 Direct Opening
(Only NC contact has a direct opening mechanism.)
When contact welding occurs, the contacts are separated
from each other by the plunger being pushed in.
Conforms to EN60947-5-1 Direct Opening
(Both NC contacts have a direct opening mechanism.)
When contact welding occurs, the contacts are separated
from each other by the plunger being pushed in.
Fixed contact (NC)
Contact spring
Fixed contact (NC)
Plunger
Return spring
Movable contact
Plunger
Contact spring
Movable contact
Return spring
Fixed contact (NO)
Contact Form
Model
Contact
Contact form
Za
D4B-@1@N
1NC/1NO
(Snap-action)
13
14
Diagrams
11-12
ON
13-14
11
Explanation
Terminal numbers 11-12 and
13-14 cannot be used as unlike
poles.
Stroke
12
Zb
D4B-@5@N
1NC/1NO
(Slow-action)
11
12
11-12
ON
23-24
23
Zb
D4B-@A@N
2NC
(Slow-action)
11-12
11
21
12
22
ON
21-22
Stroke
Only NC contact 11-12 has a
certified direct opening
mechanism.
Terminal numbers 11-12 or
23-24 can be used as unlike
poles.
Stroke
24
Only NC contact 11-12 has a
certified direct opening
mechanism.
Both NC contacts 11-12 and
21-22 have a certified direct
opening mechanism.
Terminal numbers 11-12 and
21-22 can be used as unlike
poles.
Note: Terminal numbers are according to EN50013; contact symbols are according to IEC60947-5-1.
6
D4B-@N
Dimensions and Operating Characteristics
(Unit: mm)
Note: Omitted dimensions are the same as those for the Roller Lever Type Models
D4B-2@@@N have a G1/2 conduit opening.
D4B-4@@@N have a M20 conduit opening.
Switches
Roller Lever
D4B-@@11N
Roller Lever (Stainless Steel Roller)
D4B-@@15N 17.5 × 7 stainless steel roller
62±1
17.5 dia. × 6.6 resin roller
PT
21° ±3°
M5 × 12
56
28.3
Allen-head bolt
Four, M3.5 × 19.5
head
mounting screws
31.5R
Set position
indicator plate
*1
23
131.3±1.2
60±0.2
11.5
131.3±1.2
77
15
30±0.2
60±0.2
+1
0
Adjustable Roller Lever *2
D4B-@@16N
19 dia. × 7
resin roller
25 to 89R
28.3
Four, M3.5 × 24.5
head
mounting screws
3 dia. × 160
stainless steel
rod
74
15
30±0.2
+1
0
74
30±0.2
40
43
77
7.3
5.3
Conduit opening
31.5
40
99.5
Two, M4 × 12 cover
mounting screws Cover
8
5.3
22.5
Two, 5.3-dia.
mounting holes
60±0.2
7.3
8
Four, M3.5 × 24.5
head
mounting screws
M5 × 12
Allen-head bolts
99.5
Two, M4 × 12 cover
mounting screws
Cover
16
Setting position
indicator *1
23
77
56.8
28.3
145 max.
22.5
Two, 5.3-dia.
mounting holes
3
60±0.2
66±1
5.4
16
Conduit opening
43
Adjustable Rod Lever *2
D4B-@@17N
M5 × 16
Allen-head bolts
2
23
+1
0
Set position
indicator plate *1
1
15
31.5
40
64.4
77
7.3
30±0.2
71±1
53
46.8
99.5
74
5.3
Conduit opening
31.5
43
40
22.5
Two, 5.3 dia.
mounting holes
Two, M4 × 12
cover mounting
screws
Cover
8
5.3
Four, M3.5 × 19.5
head
mounting screws
11.5
99.5
7.3
8
16
Set position
indicator plate *1
23
74
56
28.3
31.5R
22.5
Two, 5.3-dia.
mounting holes
Two, M4 × 12
cover mounting
Cover
screws
62±1
PT
21°±3° M5 × 12
Allen-head bolt
16
+1
0
15
Conduit opening
31.5
43
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
*1. The lever can be set to any desired position by turning the operating position indicator.
*2. In terms of construction, the Switch is a General-purpose Limit Switch rather than a Safety Limit Switch.
Operating characteristics
Operating force
Release force
Pretravel
Overtravel
Movement differential
Direct opening travel
Direct opening force
Total travel
Model D4B-@@11N D4B-@@15N D4B-@@16N D4B-@@17N
*1
*2
OF max.
RF min.
PT
PT (2nd) *3 *5
OT min.
MD max. *4
DOT min. *3 *6
*4 *6
DOF min. *6
TT *5
9.41N
1.47N
21°±3°
(45°)
50°
12°
35°
55°
19.61N
(75°)
9.41N
1.47N
21°±3°
(45°)
50°
12°
35°
55°
19.61N
(75°)
9.41N
1.47N
21°±3°
(45°)
50°
12°
35°
55°
19.61N
(75°)
2.12N
0.29N
21°±3°
(45°)
50°
12°
35°
55°
19.61N
(75°)
Note: Variation occurs in the simultaneity of contact opening/closing operations of 2NC contacts. Check contact operation.
*1. The operating characteristics of these Switches were measured with the roller level set at 31.5 mm.
*2. The operating characteristics of these Switches were measured with the rod level set at 140 mm.
*3. Only for slow-action models.
*4. Only for snap-action models.
*5. Reference values.
*6. Must be provided to ensure safe operation.
7
D4B-@N
Top Plunger
D4B-@@70N
Top Roller Plunger
D4B-@@71N
16
PT
9.2 dia.
Stainless steel
plunger
Two, 5.3-dia.
mounting holes
74
77
8
5.3
15
30±0.2
40
Conduit opening
97
74
5.3
30±0.2
31.5
+1
0
20
Two, M4 × 12 cover
mounting screws
Cover
7.3
60±0.2
7.3
8
Four, M3.5 × 19.5
head
mounting screws
Two, 5.3-dia.
mounting holes
97
Two, M4 × 12 cover
mounting screws
Cover
16
9.2 dia.
OP
20
OP
60±0.2
12.7 dia. × 4.8
stainless steel roller
PT
Four, M3.5 × 19.5
head
mounting screws
+1
0
43
40
15
77
Conduit opening
31.5
43
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
Operating characteristics
Operating force
Release force
Pretravel
Model
D4B-@@70N
D4B-@@71N
Overtravel
Movement differential
Direct opening travel
Direct opening force
Total travel
OF max.
RF min.
PT max.
PT (2nd) *1 *3
OT min.
MD max. *2
DOT min. *4
DOF min. *4
TT *3
18.63 N
1.96 N
2 mm
(3 mm)
5 mm
1 mm
3.2 mm
49.03 N
(7 mm)
18.63 N
1.96 N
2 mm
(3 mm)
5 mm
1 mm
3.2 mm
49.03N
(7 mm)
Free position
Operating position
FP max.
OP
38 mm
35±1 mm
51 mm
48±1 mm
Note: Variation occurs in the simultaneity of
contact opening/closing operations of
2NC contacts. Check contact
operation.
*1. Only for slow-action models.
*2. Only for snap-action models.
*3. Reference values.
*4. Must be provided to ensure safe
operation.
8
D4B-@N
Application Precaution
Changing the Operating Direction
Operating section
(on back of Head)
Switches with Roller Levers
The operating direction of the lever can be easily
changed without using any tools. It can be set to
clockwise operation (CW) or counterclockwise
(CCW) operation.
Use the procedure given at the right to change
the operating direction.
Operating procedure
1. Remove the four Head set screws and remove the Head
from the Switch Box.
Head Cover
Operating
position
mark
(arrow)
2. Turn the bottom of the Head toward you, press in the Head
Cover shown in the diagram at the left, and turn the Cover
clockwise or counterclockwise.
Note: The factory setting is for “CW.CCW.”
3. The “CW” setting is for clockwise operation and the “CCW”
setting is for counterclockwise operation. Set the Cover to
the desired position.
Safety Precautions
Be sure to read the precautions for All Safety Limit Switches in the website at:http://www.ia.omron.com/.
Indication and Meaning for Safe Use
Mounting
Precautions
for Safe Use
Supplementary comments on what to do
or avoid doing, to use the product safely.
Precautions
for Correct
Use
Supplementary comments on what to do
or avoid doing, to prevent failure to
operate, or undesirable effect on product
performance.
Use four M5 screws with washers to mount the standard model. Be
sure to apply the proper torque to tighten each screw.
Mounting Dimensions (M5)
Standard Model
Precautions for Safe Use
• Do not use the Switch submerged in oil or water, or in locations
continuously subject to splashes of oil or water. Doing so may
result in oil or water entering the Switch interior. (The IP67 degree
of protection specification for the Switch refers to water penetration
while the Switch is submersed in water for a specified period of
time.)
• Always attach the cover after completing wiring and before using
the Switch. Also, do not turn ON the Switch with the cover open.
Doing so may result in electric shock.
Precautions for Correct Use
Appropriate Tightening Torque
(3)
(6)
Be sure to tighten each
screw of the D4B-@N
properly, otherwise the
D4B-@N may malfunction.
(4)
(1)
60
30
Changes in Actuator Mounting Position
• To change the angle of the lever, loosen the Allen-head bolts on
the side of the lever.
• The operating position indicator plate * has protruding parts which
engage with the lever, thus allowing changes to the lever position
by 90°.
• The back of the operating position indicator plate * has no
protruding parts. If this plate is turned over and attached, any angle
within a 360° range can be set. Do not turn over the plate, however,
when using the D4B-@N as a switch with a certified direct opening
mechanism. For an SUVA- or BIA-certified application, make sure
that the lever engages with the operating position indicator plate
securely so that the lever will not slip.
* The operating position indicator plate: Refer to page 5.
Changes in Head Mounting Position
By removing the screws on the four corners of the head, the head can
be reset in any of four directions. Make sure that no foreign materials
will penetrate through the head.
(5)
Type
1 M3.5 terminal screw
(2)
Appropriate tightening
torque
0.59 to 0.78 N·m
2 Cover mounting screw *
1.18 to 1.37 N·m
3 Head mounting screw
0.78 to 0.88 N·m
4 M5 body mounting screw
4.90 to 5.88 N·m
5 Connector
1.77 to 2.16 N·m
Lever Mounting Screws (Roller
6
4.90 to 5.88 N·m
Levers)
9
D4B-@N
Wiring
Conduit Opening
Do not connect the bare lead wires directly to the terminals but be
sure to connect each of them by using an insulation tube and M3.5
round crimp terminals and tighten each terminal screw within the
specified torque range.
The proper lead wire is 20 to 14 AWG (0.5 to 2.5 mm2) in size.
dz dia.:
D dia.:
B:
L:
F:
l:
• Make sure that each connector is tightened within the specified
torque range.
The casing may be damaged if the connector is tightened
excessively.
• Use an OMRON SC-series Connector (sold separately) that is
suited to the cable in diameter.
Others
3.7 mm
4.5 mm
7.0 mm
20.2 mm D dia.
7.7 mm
9.0 mm
• The load for the actuator (roller) of the Switch must be imposed on
the actuator in the horizontal direction, otherwise the actuator or
the rotating axis may be deformed or damaged.
Correct
Incorrect
dz dia.
Make sure that all crimp terminals come into contact with the casing
or cover as shown below, otherwise the cover may not be mounted
properly or the D4B-@N may malfunction.
Correct
Crimp terminal
Terminal screw
Cover
Cover
Casing
θ
θ
Incorrect
Terminal screw
Crimp
terminal
Dog
• When using a long lever model, the D4B-@@16N or D4B-@@17N, the
Switch may telegraph. To avoid telegraphing, take the following
precautions.
1. Set the lever to operate in one direction.
2. Modify the rear end of the dog to an angle of 15° to 30° as
shown below or to a secondary-degree curve.
Incorrect
Terminal screw
Correct
Dog
θ ≥ 30°
15° ≤ θ ≤ 30°
3. Modify the circuit so as not to detect the wrong operating
signals.
Crimp terminal
Casing
Correct
Crimp terminal
Incorrect
Crimp terminal
10
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change without notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the importation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security interest in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original transportation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
14.
15.
16.
17.
18.
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for published information.
Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or settle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
Property; Confidentiality. Any intellectual property in the Products is the exclusive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law principles). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability. If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Companies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this Product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
2.
3.
4.
5.
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.55.59.01.43.00 • 01-800-226-6766 • mela@omron.com
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • mela@omron.com
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu
Authorized Distributor:
Automation Control Systems
• Machine Automation Controllers (MAC) • Programmable Controllers (PLC)
• Operator interfaces (HMI) • Distributed I/O • Software
Drives & Motion Controls
• Servo & AC Drives • Motion Controllers & Encoders
Temperature & Process Controllers
• Single and Multi-loop Controllers
Sensors & Vision
• Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors
• Amplified Photomicrosensors • Measurement Sensors
• Ultrasonic Sensors • Vision Sensors
Industrial Components
• RFID/Code Readers • Relays • Pushbuttons & Indicators
• Limit and Basic Switches • Timers • Counters • Metering Devices
• Power Supplies
Safety
• Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety
Controllers • Light Curtains • Safety Relays • Safety Interlock Switches
C72I-E-02
04/15
Note: Specifications are subject to change.
Printed on recycled paper.
© 2015 Omron Electronics LLC
Printed in U.S.A.
