Guard Lock Safety-door Switch
D4BL
C39I-E-02
Release Protective Cover Locks Using
Controller Signals or Pushbutton
Switches after the Cutting Tool Stops
Moving Due to Inertia
Note: Contact your sales representative for details
on models with safety standard certification.
• A mechanical lock is applied automatically when the Operation
Key is inserted. A high level of safety is achieved using a
mechanism where the lock is only released when voltage is
applied to the solenoid.
• Conforms to EN (TÜV) standards corresponding to the CE
marking.
• Certified by UL, CSA and CCC standards.
• The Switch contact is opened by a direct opening mechanism
(NC contacts only) when the protective cover is opened. Direct
opening mechanism that is EN-certified is indicated by on the
Switch.
• Auxiliary release key ensures easy maintenance and unlocks the
door in the case of a power failure.
• Tough aluminum die-cast body incorporating a switch box with
degree of protection satisfying IP67, UL, and CSA TYPE6P, 13.
• Equipped with a horizontal and vertical conduit opening.
• Models incorporating easy-to-see indicators for monitoring and
those using an adjustable Operation Key for a swinging door are
available.
• The mounting direction of the head can be changed
Be sure to read the “Safety Precautions” on page 13.
to allow the Operation Key to be inserted from four
directions.
• Conforms to ISO 14119.
Model Number Structure
Model Number Legend
Switch
D4BL -
1
2
3
4
-
5
1. Conduit Size (2-conduit)
1: PG13.5
2: G1/2
4: M20
2. Built-in Switch (with Safety Switch and Lock Monitor Switch
Contacts)
C: 1NC/1NO (slow-action) + 1NC (slow-action)
D: 2NC (slow-action) + 1NC (slow-action)
3. Head Mounting Direction
R: Four mounting directions possible (right-side mounting at
shipping)
4. Door Lock and Release (Auxiliary Release Key is Incorporated
by All Models)
A: Mechanical lock/24 VDC solenoid release
G: 24 VDC Solenoid lock/Mechanical release
5. Indicator
Blank: Without indicator
A: 10 to 115 VAC or VDC driving (with orange and green LED
indicator unit)
Operation Key
D4BL - K
1
1. Operation Key Type
1: Horizontal mounting
2: Vertical mounting
3: Adjustable mounting (Horizontal)
1
D4BL
Switch
Operation Key
D4BL -2GRD-AT
1 2 3 4
D4BL - K
5
1. Conduit Size (2-conduit)
2: G1/2
2. Built-in Switch
G: 2NC (slow-action) + 2NC (slow-action)
3. Head Mounting Direction
R: Four mounting directions possible (right-side mounting at
shipping)
4. Door Lock and Release
D: Mechanical lock/24 VDC solenoid release
5. Indicator lamp
A: Equipped with an orange/green LED display unit
1
1. Operation Key Type
1: Horizontal mounting
2: Vertical mounting
3: Adjustable mounting (Horizontal)
Ordering Information
List of Models
Switches (Operation Keys are sold separately.)
: Models with certified direct opening contacts.
Consult with your OMRON representative when ordering any models that are not listed in this table.
Lock
method
Mechanical
lock
Solenoid
lock
Without indicator
1NC/1NO+ 1NC
(Slow-action)
With LED indicator
1NC/1NO+ 1NC
(Slow-action)
Without indicator
2NC+ 1NC
(Slow-action)
With LED indicator
2NC+ 1NC
(Slow-action)
D4BL-1CRA
D4BL-1CRA-A
D4BL-1DRA
D4BL-1DRA-A
D4BL-2CRA
D4BL-2CRA-A
D4BL-2DRA
D4BL-2DRA-A
M20
D4BL-4CRA
D4BL-4CRA-A
D4BL-4DRA
D4BL-4DRA-A
Pg 13.5
D4BL-1CRG
D4BL-1CRG-A
D4BL-1DRG
D4BL-1DRG-A
D4BL-2CRG
D4BL-2CRG-A
D4BL-2DRG
D4BL-2DRG-A
D4BL-4CRG
D4BL-4CRG-A
D4BL-4DRG
D4BL-4DRG-A
Conduit
size
Voltage
for
solenoid
PG13.5
G1/2
G1/2
M20
24 VDC
24 VDC
Operation Keys
Mounting type
Model
Horizontal mounting
D4BL-K1
Vertical mounting
D4BL-K2
Adjustable mounting
D4BL-K3
2
D4BL
Specifications
Standards and EC Directives
Conforms to the following EC Directives:
Certified Standards
• Machinery Directive
• Low Voltage Directive
• EN ISO 14119
Certification body
TÜV Rheinland
Certified Standard Ratings
Standard
EN60947-5-1
(certified direct
opening)
GS-ET-19
UL
UL508
CSA
CSA C22.2, No.14
CQC (CCC)
GB14048.5
File No.
Consult your OMRON
representative for details.
E76675
LR45746
2003010305073836
TÜV (EN60947-5-1), CCC (GB14048.5)
Standard model
Indicator model
AC-15
AC-15
Rated operating current (Ie)
3A
6A
Rated operating voltage (Ue)
250 V
115 V
Item
Type
Utilization category
Note: Use a 10 A fuse type gI or gG that conforms to IEC60269 as a short-circuit protection device.
UL/CSA (UL508, CSA C22.2 No. 14)
A300
Rated voltage
120 VAC
240 VAC
Carry current
10 A
Current (A)
Volt-amperes (VA)
Make
Break
60
6
30
3
Make
Break
7,200
720
Note: The UL/CSA certified rating for products with indicators (-A) is 6 A/115 VAC.
3
D4BL
Characteristics
Degree of protection *1
Durability *2
IP67 (EN60947-5-1)
Mechanical
1,000,000 operations min.
Electrical
500,000 operations min. (10 A resistive load at 250 VAC)
Operating speed
0.05 to 0.5 m/s
Operating frequency
30 operations/minute max.
Direct opening force *3
19.61 N min. (EN60947-5-1)
Direct opening travel *3
20 mm min. (EN60947-5-1)
Holding force
700 N min. (GS-ET-19)
Contact resistance
50 mΩ max.
Rated insulation voltage (Ui)
300 V (EN60947-5-1)
Rated frequency
50/60 Hz
Protection against electric shock
Class I (with ground terminal)
Pollution degree (operating environment)
3 (EN60947-5-1)
Between terminals
of same polarity
Impulse withstand
voltage
(EN60947-5-1)
Between terminals
of different polarity 4 kV
Between each
terminal and
ground
Between solenoid
and ground
Insulation resistance
100 MΩ min. (at 500 VDC)
Contact gap
Vibration resistance
Shock resistance
2.5 kV
2 × 2 mm min.
Malfunction
10 to 55 Hz, 0.35 mm single amplitude
Destruction
1,000 m/s2 min.
Malfunction
300 m/s2 min.
Conditional short-circuit current
100 A (EN60947-5-1)
Conventional enclosed thermal current (Ithe) 10 A (EN60947-5-1)
Ambient operating temperature
–10 to 55°C (with no icing)
Ambient operating humidity
95% max.
Weight
Approx. 800 g
Note: The above values are initial values.
*1. The degree of protection is tested using the method specified by the standard (EN60947-5-1). Confirm that sealing properties are sufficient for
the operating conditions and environment beforehand. Although the switch box is protected from dust, oil or water penetration, do not use the
D4BL in places where dust, oil, water, or chemicals may enter through the key hole on the head, otherwise Switch damage or malfunctioning
may occur.
*2. The durability is for an ambient temperature of 5 to 35°C and an ambient humidity of 40% to 70%.
*3. These figures are minimum requirements for safe operation.
Solenoid Coil Characteristics
Item
Type
24 VDC mechanical lock models
Rated operating voltage
24 VDC
Current consumption
+10%
−15%
24 VDC solenoid lock models
(100% ED)
Approx. 300 mA
Insulation class
Class B (130°C or less)
Indicator Characteristics
Rated voltage
10 to 115 VAC/VDC
Current leakage
Approx. 1 mA
Color (LED)
Orange, green
4
D4BL
Structure and Nomenclature
Structure
D4BL-@CR@-@
D4BL-@DR@-@
Operation Key
Lock plate
Operation Key
Lock plate
Auxiliary release key
Lock monitor switch
Solenoid
Auxiliary release key
Rotating drum
Operation plunger
Rotating drum
Lock monitor switch
Solenoid
Operation plunger
Seal ring (NBR)
Auxiliary plunger
Seal packing (NBR)
Rotating lever
Seal ring (NBR)
Auxiliary plunger
Seal packing (NBR)
Rotating lever
Safety switch
Safety switch
Seal packing (NBR)
Seal packing (NBR)
Conduit opening
Connection
(Pull out
terminal M3.5
horizontally)
Conduit opening
Conduit opening
(Pull out
(Pull out
horizontally)
vertically)
Ground terminal M3.5
Connection
terminal M3.5
Ground terminal M3.5
Conduit opening
(Pull out
vertically)
The head can be changed
to any of four directions.
Contact Form (Diagrams Show State with Key Inserted and Lock Engaged)
Model
Contact
(door open/
closed detection
and lock monitor)
Contact form
Operating pattern
Door open/
closed detection
Lock monitor
Remarks
Lock position
Door
open/closed detection
Lock monitor
D4BL-@CR@-@
1NC/1NO+1NC
31
32
11
Zb
12
Operation Key
insertion completion
position
24
23
ON
Stroke
The terminals 11-12
and 23-24 can be
used as unlike poles.
Extraction
completion
position
Lock position
Door
open/closed detection
Lock monitor
D4BL-@DR@-@
2NC+1NC
31
32 11
Zb
21
Note: The EN-certified direct opening mechanism is indicated by
12
22
ON
Stroke
Operation Key
insertion completion
position
Extraction
completion
position
Only NC contacts 11-12
have a certified direct
opening mechanism.
Only NC contacts
11-12 and 21-22
have a certified
direct opening
mechanism.
The terminals 11-12
and 21-22 can be
used as unlike poles.
on the Switch.
Contact Form (D4BL-2GRD-AT)
(Safety circuit side)
(Monitor circuit side)
5
D4BL
Dimensions and Operating Characteristics
(Unit: mm)
Switches
D4BL-@@R@-@
Four, M3.5 head
clamping screws
(116.5)
Red
31.5
17
10
74±0.1
6.8
100±0.1
112+1
0
(116.5)
Four, M3.5 head
clamping screws
Model
D4BL-@@R@-@
Key insertion force
Key extraction force
19.61 N max.
19.61 N max.
Movement before
being locked
15 mm max.
Total travel
23 mm min.
31.5
17
10
7
Indicator
(Green:
Solenoid ON).
37.5
Four, 5.3 dia.
Mounting
holes
Four, M4
cover
clamping
screws
Cover
(123.5)
74±0.1
6.8
Conduit opening
Operating
Characteristics
46.3
Conduit opening
D4BL-2GRD-AT
34.2
86+10
16
39.6
5.5
Indicators
Red
37.5
Four, 5.3 dia.
mounting
holes
Four, M4
cover
clamping
screws
Cover
(123.5)
Conduit opening
7
Lock
protection
cap
15
34.2
100±0.1
+1
1120
5.5
+1
0
86
16
39.6
42.6
Indictor
Conduit opening
(Orange: Switch OFF)
Conduit opening
Operating
Characteristics
Model
D4BL-2GRD-AT
Key insertion force
Key extraction force
19.61 N max.
19.61 N max.
Movement before
being locked
15 mm max.
Total travel
23 mm min.
Note: 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
2. There are fluctuations in the contact ON/OFF timing for 2NC contacts. Confirm performance before application.
6
D4BL
Operation Keys
D4BL-K1
D4BL-K3
Red
78.7
40.7
20
12
Red
Long mounting hole
7.3 15
25.8 15.6
5.3
36
5.3
Two, 2.65R
2.6
Red
7.5
20
11.8
5.6
4 dia.
4
D4BL-K2
12
40
20
18°
53.7
Red
26
13
25.8 15.6
5.3 x 7.3 long mounting hole
40
15.6
18°
(80.7)
40
30
52.4
36
11.8
30
36
5.3 11.9 7.5
20
11.8
5.3 dia.
2.6
19.5
5.6
(37.8)
4 dia.
17.5
34.6
M4 Allen-head bolt
5.6
4 dia.
2.6
7
D4BL
With Operation Key Inserted
D4BL + D4BL-K2
D4BL + D4BL-K1
D4BL + D4BL-K3
Red
Red
53.5 min. 57 max.
(41)
(12)
Horizontal direction
Operation Key
insertion radius
R ≥ 1200
54.5 min. 58 max.
(20±0.15)
(41)
Horizontal direction
Operation Key
insertion radius
R ≥ 250
Horizontal direction
Operation Key
insertion radius
R ≥ 1200
(13)
Red
81.5 min. 85 max.
(41)
(40)
(40±0.15)
(30±0.15)
Vertical direction
Operation Key
insertion radius
R ≥ 1000
Vertical direction
Operation Key
insertion radius
R ≥ 1000
Vertical direction
Operation Key
insertion radius
R ≥ 1000
54.5 min. 58 max.
53.5 min. 57 max.
(20±0.15)
(41)
81.5 min. 85 max.
(41)
(41)
(35)
(35)
(35)
Note: 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
2. In the above diagrams, the Operation Key is inserted from the front.
8
D4BL
Indicator Unit
Four terminal plates
Two, 7 dia.
(7)
Two LED
(16)
26.8 53.2 57.2
(16)
0.3
5.6
2
10.6
(12.6)
(35)
26.2
(61.2)
Connections
Internal Circuit Diagram
Indicator
10 to 115 VAC/VDC
Solenoid
24 VDC
R
ZD
R
E1 (+)
LED
E2 (−)
Constant-current diode
9
D4BL
Circuit Connection Example
• Terminals 11 and 32 are connected internally and so connect terminals 12 and 31 for safety-circuit input. (GS-ET-19).
• When using indicators, connect them to the auxiliary circuit side (monitor circuit) or in parallel between E1 and E2 as shown below.
• Do not connect the indicators in parallel with the direct opening contact. If the indicators are broken, a short-circuit current may flow, causing
equipment to malfunction.
• The 24 VDC solenoid terminals have polarity. Confirm the polarity before wiring.
1. Orange: Lights when the solenoid turns ON.
Green: Lights when the door opens.
2. Orange: Lights when the solenoid turns ON.
Green: Lights when power turns ON.
(Power supply side)
(Power supply side)
E1 (+)
12
11
23
24
32
31
Solenoid
LED (orange)
E2 (−)
E1 (+)
12
11
23
24
32
31
LED (orange)
LED (green)
Auxiliary circuit
(monitor circuit)
Solenoid
LED (green)
Auxiliary circuit
(monitor circuit)
Safety circuit
3. Orange: Lights when the solenoid turns ON.
Green: Lights when door closes.
(Power supply side)
Safety circuit
4. Orange: Lights when the solenoid turns ON.
Green: Lights when power turns ON.
(Power supply side)
E1 (+)
E1 (+)
12
11
21
22
32
31
Solenoid
LED (orange)
E2 (−)
12
11
21
22
32
31
Safety circuit
Solenoid
LED (orange)
LED (green)
Auxiliary circuit
(monitor circuit)
E2 (−)
E2 (−)
LED (green)
Auxiliary circuit
(monitor circuit)
Safety circuit
10
D4BL
Connection Example with OMRON’s G9SA Safety Relay Unit
G9SA-321-T@ (24 VAC/VDC) + D4BL-@DRA-@ (Mechanical Lock Type) Circuit Diagram (Manual Reset)
Lock release signal
KM1
KM2
S2
S4
31
S1:
Safety Limit Switch
with direct opening mechanism
(D4B-N, D4N, D4F)
S2:
Guard Lock Safety-door Switch
S3:
Reset switch
S4:
Lock release switch
KM1 and KM2: Magnetic Contactor
M:
3-phase motor
32
11
21
12
22
PLC
Guard
S1
Feedback loop
OPEN
KM1
S3
KM2
Stop signal
A1 A2 T11
TH
T12
T31
T32
13 23 33 43 53 61
1
a
K1
SA
K2
K3
K3
a
K1
b
K2
K4
3
4
Off-Delay
Timer
K4
Control
Circuit
b
2 K1
5
K2
JP
1
2
3
4
5
6
6
PE T21
T23 T22
A
14 24 34 44 54 62
B
KM1 KM2
Guard opens
Timing Chart
Limit switch S1
Guard Lock
Safety-door
Switch S2
Lock release
signal
Operation
instruction
Motor controller
KM1
S4
Guard can be opened
Stop signal
Reset switch
S3
K1 and K2
(NC)
K1 and K2
(NO)
K3 and K4
(NC)
KM2
M
Note: This example circuit is for Category 3.
K3 and K4
(NO)
KM1 and KM2
(NC)
KM1 and KM2
(NO)
Operation
instruction
Motor rotation
OFF-delay time
11
D4BL
G9SA-301 (24 VAC/VDC) + D4BL-@DRG-@ (Solenoid Lock Type) Circuit Diagram (Auto-reset)
Lock signal
S2
31
32
11
21
12
22
S1:
Safety Limit Switch
with direct opening mechanism
(D4B-N, D4N, D4F)
S2:
Guard Lock Safety-door Switch
KM1 and KM2: Magnetic Contactor
M:
3-phase motor
S1
PLC
12
OPEN
Feedback loop
11
KM1
KM2
Operation signal
A1 A2 T11
TH
T31
T12
T32
1
a
K1
K1 K2
SA
13 23 33 41
3
4
K2
K1
b
K2
a
b
Control
Circuit
2
5
JP
1
2
3
4
5
6
6
PE T21
T23 T22
A
B
14 24 34 42
KM1 KM2
Operation
instruction
Timing Chart
Limit switch S1
Guard Lock
Safety-door
Switch S2
Motor controller
Guard opens
KM1
KM2
Operation signal
Lock signal
K1 and K2
(NC)
K1 and K2
(NO)
KM1 and KM2
(NC)
KM1 and KM2
(NO)
M
Note: 1. This example circuit is for Category 4.
2. The lock can be released at any time. Therefore, do
not use a model with a solenoid lock in applications
where the operator may be exposed to danger when
the guard opens. Use a model with a mechanical
lock.
12
D4BL
Safety Precautions
● Be sure to read the precautions for all D4BL models in the website at: http://www.ia.omron.com/.
Precautions for Correct Use
DANGER
Injury may occasionally occur. Always check to make
sure that the safety functions operate correctly before
using the machine. The safety functions may not operate
correctly because of wiring mistakes, setting mistakes,
or Switch malfunction, causing some machines to
continue operating in situations where they should be
stopped.
Injury may occasionally occur. If the machine is used
with the release key in the UNLOCK position, the
electromagnetic lock may not operate, causing some
machines to continue operating in situations where they
should be stopped. Be sure to put the release key in the
LOCK position before using the machine. Also, check
the condition of the lock and safety circuits.
Injury may occasionally occur. When the
electromagnetic lock function or Switch function is
damaged, some machines may continue operating in
situations where they should be stopped. Do not use the
electromagnetic lock function of the Switch in place of a
door lock. Always provide a lock separate from the
Switch, attach a warning seal to prevent people from
using excessive force to open the door when it is locked,
or provide an indicator lamp to show the locked/unlocked
status of the door.
Appropriate Tightening Torque
Loose screws may result in malfunction. Tighten the screws to the
specified torques.
No.
Appropriate
tightening
torque
Type
1
M3.5 terminal screw
(including terminal screw)
2
Cover mounting screw
1.18 to 1.37 N·m
3
Head mounting screw
0.78 to 0.98 N·m
4
M5 body mounting screw *
4.90 to 5.88 N·m
5
Operation Key mounting screw
2.35 to 2.75 N·m
6
Connector
1.77 to 2.16 N·m
7
Cap screw
1.27 to 1.67 N·m
0.59 to 0.78 N·m
* Use M5 screws. Apply a torque of 4.90 to 5.88 N·m for an
Allen-head bolt. For a pan head screw, apply a torque of 2.35 to
2.75 N·m
5. Two, M5 Operation Key mounting screw
3. Four, M3.5 head-mounting screw
Precautions for Safe Use
• Do not use the Switch submersed in oil or water or in locations
continuously subject to splashes of oil or water. Doing so may
result in oil or water entering the Switch. (The IP67 degree of
protection of the Switch specifies the amount of water penetration
after the Switch is submerged in water for a certain period of time.)
• Always attach the cover after completing wiring and before using
the Switch. Also, do not turn ON the Switch with the cover open.
Doing so may result in electric shock.
• Make sure the Switch is mounted securely to prevent it from falling
off. Otherwise injury may result.
Stopper Installation
Do not use a Switch as a stopper. Be sure to install a stopper as
shown in the following illustration when mounting the Switch so that
the Operation Key is within 0.5 to 5 mm of the set zone.
Do not subject the Switch to a shock that exceeds the Switch's shock
resistance of 1,000 m/s2.
Incorrect
Correct
2. Four, M4 cover-mounting
screw
6. Conduit
7. Conduit cap
4. Four, M5
switch-mounting screw
Auxiliary Release Key
• The auxiliary release key is used to unlock the D4BL in case of
emergency or in case the power supply to the D4BL fails.
• Use the enclosed Release Key to change the lock from LOCK to
UNLOCK so that the lock will be released and the door can be
opened. (Applies only to mechanical locks. Release key is not
provided with D4BL-2GRD-AT.)
LOCK
Stopper
UNLOCK
Auxiliary
release key
Switch
Incorrect
Gap
Set zone
Correct
• Whenever the lock has been changed to UNLOCK, always return
it to LOCK before using the Switch.
• Do not use the auxiliary release key to start or stop machines.
• Make sure that the auxiliary release key is kept with the person in
charge.
• To prevent the auxiliary release key from being handled carelessly
by unauthorized people, seal the auxiliary release key with sealing
wax and the provided seal cap to ensure IP67.
• Before attaching the cover to the D4BL, make sure that the
auxiliary release key position is set to LOCK.
Solenoid Lock Models
The solenoid lock locks the door only when power is supplied to the
solenoid. Therefore, the door will be unlocked if the power supply to
the solenoid stops. Therefore, do not use solenoid lock models for
machines that may be operating and dangerous even after the
machine stops operating.
13
D4BL
Switch and Operation Key Mounting
Use four M5 screws and spring washers to mount the Switch and
Operation Key, and tighten the screws to a suitable torque.
To ensure safety, use screws that cannot be easily removed or
another means to prevent the Switch and Operation Key from easily
being removed.
Mounting Dimensions
Switch Mounting Dimensions
Four, M5
Head Direction
• The head can be mounted in four directions by loosening the four
screws holding the head. To remove the head, turn the head at the
surface mating with the Switch body by 45° as shown in figures (A)
and (B) below.
To change the direction of the head, make sure that the protruding
part of the rotating lever engages with the groove of the plunger.
Then turn the head clockwise or counterclockwise to the desired
direction. At that time, make sure that the groove of the plunger is
located under the rotating lever. If the direction of the head is not
set when the plunger is rotated by 45°, the groove of the plunger
presses the rotating lever. The head, plunger, or the built-in switch
may be damaged as a result.
Head Direction Changes
74±0.1
Left
Front
100±0.1
(45°)
Operation Key Mounting Holes
D4BL-K1
Two, M5
(A)
(45°)
Back
Right
20±0.1
D4BL-K2
(B)
Head Bottom View
Switch Top View
Two, M5
40±0.1
D4BL-K3
Two, M5
30±0.1
Operation Key
Rotation lever and
protruding part
Normal Positions of Rotating Lever and Plunger
Switch body
• The D4BL is provided with a shock-absorbing damper to protect
the D4BL from damage that may result from dropping the D4BL
during transportation. Be sure to remove the damper after
mounting the D4BL.
• The mounting tolerance of the Operation Key is ±0.3 mm vertically
or horizontally. Be sure to mount the D4BL correctly without
misalignment, otherwise the D4BL may soon break or wear out.
• Observe the specified insertion radius for the Operation Key and
insert it in a direction perpendicular to the key hole.
Incorrect
Operation plunger and
groove mechanism
Greater
than ±0.3
Rotating lever (with
protruding part)
Plunger (with groove)
Built-in switch
• Be sure to check the mechanical lock and solenoid release
functions when mounting the D4BL.
• If the head direction is changed, recheck the tightening torque of
each of screw. Make sure that no foreign materials will enter
through the key hole on the head.
Incorrect
Greater
than ±0.3
• Do not use the D4BS operation key.
14
D4BL
Processing and Connecting Cable/
Conduit
Cable Connection Example
1. Connect the wires to the terminals in the order shown below for
wiring efficiency.
• The following procedures are recommended for mounting and
wiring the indicator unit securely.
• To ensure IP67, use OMRON’s SC-@M and Nippon Flex’s
ABS-08Pg13.5 and ABS-12 Pg13.5 Connectors.
• Recommended cable: UL2464-type cable that is AWG20 to
AWG18 (0.5 to 1.0 mm2) in size and has seven conductors
• Connect the indicator unit after connecting the seven-conductor
cable.
Tighten each wired terminal clockwise to a torque of 0.59 to
0.78 N·m.
Terminal no.
Lp (mm)
Lv (mm)
E1
30±2
80±2
E2
35±2
75±2
31
45±2
60±2
12
55±2
50±2
23 (21)
65±2
45±2
24 (22)
70±2
35±2
90±2
50±2
a (mm)
Twist the wire two or three times and make sure that no bare wire
exists outside the terminal when tightening the terminal.
2. The insulation sheath of the seven-conductor cable must come into
contact with the wall of the conduit mouth, side A or side B.
8±1
• Properly attach and securely tighten the provided conduit cap to
the unused conduit opening to the suitable tightening torque when
wiring the D4BL.
Insulation sheath edge
Others
Do not touch the solenoid because the solenoid radiates heat while
power is being supplied.
15
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change without notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the importation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security interest in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original transportation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
14.
15.
16.
17.
18.
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for published information.
Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or settle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
Property; Confidentiality. Any intellectual property in the Products is the exclusive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law principles). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability. If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Companies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this Product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
2.
3.
4.
5.
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.55.59.01.43.00 • 01-800-226-6766 • mela@omron.com
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • mela@omron.com
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu
Authorized Distributor:
Automation Control Systems
• Machine Automation Controllers (MAC) • Programmable Controllers (PLC)
• Operator interfaces (HMI) • Distributed I/O • Software
Drives & Motion Controls
• Servo & AC Drives • Motion Controllers & Encoders
Temperature & Process Controllers
• Single and Multi-loop Controllers
Sensors & Vision
• Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors
• Amplified Photomicrosensors • Measurement Sensors
• Ultrasonic Sensors • Vision Sensors
Industrial Components
• RFID/Code Readers • Relays • Pushbuttons & Indicators
• Limit and Basic Switches • Timers • Counters • Metering Devices
• Power Supplies
Safety
• Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety
Controllers • Light Curtains • Safety Relays • Safety Interlock Switches
C39I-E-02
05/15
Note: Specifications are subject to change.
Printed on recycled paper.
© 2015 Omron Electronics LLC
Printed in U.S.A.
