E2FQX10D1

Chemical Resistant Inductive Proximity Sensor E2FQ Fluoro plastic housing for highest chemical and detergent resistance Ordering Information DC 3-wire models Shape Sensing distance M12 2mm PNP (NO) NPN (NO) DC 2-wire models Response NO frequency Response frequency E2FQ-X2F1 E2FQ-X2E1 1.5 kHZ E2FQ-X2D1 800 Hz E2FQ-X5F1 E2FQ-X5E1 600 Hz E2FQ-X5D1 500 Hz E2FQ-X10F1 E2FQ-X10E1 400 Hz E2FQ-X10D1 300 Hz Shielded M18 M30 5mm 10mm Characteristic data (typical) 2.2 2 #d X 1.8 t=1mm Mild steel Stainless steel (SUS304) 1.6 1.4 1.2 1 Brass E2FQ-X10# 7 #d X 6 t=1mm Mild steel 5 Stainless steel (SUS304) 4 3 2 E2FQ #d X 10 t=1mm Mild steel 9 8 7 Stainless steel (SUS304) 6 Brass 4 Aluminum Aluminum 2 1 1 0.2 0 11 3 Aluminum 0.4 12 5 Brass 0.8 0.6 Sensing distance X (mm) 2.4 . E2FQ-X5# Sensing distance X (mm) Sensing distance X (mm) Sensing Distance vs. Sensing Object E2FQ-X2# 5 10 15 20 25 Side length of sensing object d (mm) 0 5 10 15 20 25 30 35 40 50 Side length of sensing object d (mm) 0 10 20 30 40 50 60 Side length of sensing object d (mm) 1 Rating/Performance Item Model E2FQ-X2@ E2FQ-X5@ E2FQ-X10@ Sensing distance 2 mm ±10% 5 mm ±10% 10 mm ±10% Setting distance 0 to 1.6 mm 0 to 4 mm 0 to 8 mm Differential distance E1, F1 models: 10% max. of sensing distance Sensing object Ferrous metal (Sensitivity lowers with non-ferrous metals) Standard sensing object 12 x 12 x 1 mm 18 x 18 x 1 mm (mild steel) E1, F1 models: 1.5 kHz E1, F1 models: 600 Hz, Response frequency*1 D1 models: 800 Hz D1 models: 500 Hz Power supply E1, F1 models: 12 to 24 VDC, ripple (p-p) : 10% max., (10 to 30 VDC) (Operating voltage D1 models: 12 to 24 VDC, ripple (p-p) : 20% max., (10 to 36 VDC) range) Current consumption E1, F1 models: 17 mA max. Leakage current D1 models: 0.8 mA max. Control output Switching capacity Residual voltage Indicator lamp Operating status (with sensing object approaching) 30 x 30 x 1 mm E1, F1 models: 400 Hz, D1 models: 300 Hz E1, F1 models: 200 mA max., D1 models: 5 to 100 mA DC E1, F1 models: 2 V max. (load current: 200 mA with cable length: 2 m) D1 models: 3.0 V max. (under load current of 100 mA with cable length of 2 m) E models: operation indicator (red) D models: operation indicator (green for stable detection, red for detection close to threshold) Normally open (NO) Protective circuits E1, F1 models: Protection for reverse polarity, load short circuit, surge voltage Ambient temperature Operating/Storage: -25°C to 70°C (with no icing or condensation) Ambient humidity Operating/Storage: 35% to 95%RH (with no condensation) Temperature influence 10% max. of sensing distance at 23°C within temperature range of -25°C to 70°C Voltage influence E1, F1 models: ±2.5% max. of sensing distance within rated voltage range ±15% Insulation resistance 50 MW min. (at 500 VDC) between energized parts and case Dielectric strength E1, F1, D1 models: 1,000 VAC 50/60 Hz for 1 min between energized parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 for 10 times each in X, Y, and Z directions Protective structure IEC60529 IP67 Destruction: 1,000 m/s2 for 10 times each in X, Y, and Z directions Connection method Pre-wired models (standard length: 2 m) Weight (Packed state) Approx. 70 g Approx. 130 g Approx. 170 g Case Material Accessories Sensing surface Fluoro plastic Instruction manual *1. The response frequencies are average values measured on condition that the distance between each sensing object is twice as large as the size of the sensing object and the sensing distance set is half of the maximum sensing distance. 2 Inductive Sensors Output Circuit Diagram Operating status Output specifications Model Timing chart E2FQ-X@F1 Brown Yes Sensing object PNP Output circuit +V No Operates Load (between black and blue leads) Releases Output voltage H (between black and blue leads) L Black Main circuit 2.2W Operation indicator Output Load 4.7kW ON 100W OFF Blue 0V Brown 100W Yes Sensing object NPN NO E2FQ-X@E1 Load 4.7kW No Operates Main circuit Load (between black and blue leads) Releases Output voltage H (between black and blue leads) L Black 2.2W Output Blue OFF E2FQ-X@D1 Load 0V Note: 1. 200 mA max.(load current) 2. When a transistor is connected Brown DC 2-wire Tr (see note 2) ON Operation indicator Sensing object +V (see note 1) Yes +V Main circuit No Operates Releases Operation indicator Load Blue ON 0V OFF Note: The load can be connected to either the +V or the 0-V line. Precautions Correct Use Mutual Interference Design Effects of Surrounding Metal Provide a minimum distance between the Sensor and the surrounding metal as shown in the table below. D m Item (Unit: mm) l E2FQ-X2# d D 12 0 18 30 0 m n 8 18 20 27 40 45 Mutual Interference If more than one Proximity Sensor is installed face to face or in parallel, ensure that the distances between two Units adjacent to each other are the same as or larger than the corresponding values shown in the following table. E2FQ B 20 E2FQ-X5# 50 35 E2FQ-X10# 100 70 A B l Effects of Surrounding Metal E2FQ-X10# A 30 n m d dia. E2FQ-X5# E2FQ-X2# Installation Do not tighten the nut with excessive force. A washer must be used with the nut. l Model Model (Unit: mm) Item Note: The table below shows the value of tightening torques when using toothed washers. Torque Model Tensile strength (torque) E2FQ-X2# E2FQ-X5# E2FQ-X10# 0.98 Nm 2 Nm Others Chemical resistance 3 Dimensions (Unit: mm) E2FQ-X2E1 E2FQ-X2F1 E2FQ-X2D1 38 38 21 dia. 17 21 dia. 17 27 24 M12 x 1 (see note) Indicator Two, clamping nut 6 27 24 M12 x 1 (see note) Indicator Two, clamping nut 6 Two, Toothed washers Two, Toothed washers Note: Oil-resistant, vibration-resistant, and fire-retardant vinyl-insulated round cord, 6 dia. x 2 cores, standard length: 2 m The cord can be extended in an independent conduit for 200 m maximum. Note: Oil-resistant, vibration-resistant, and fire-retardant vinyl-insulated round cord, 6 dia. x 3 cores, standard length: 2 m The cord can be extended in an independent conduit for 200 m maximum. E2FQ-X5D1 E2FQ-X5E1 E2FQ-X5F1 47 47 40 32 29 29 dia. 24 40 32 29 29 dia. 24 (see note) (see note) Indicator M18 x 1 8 Indicator Two, clamping nut M18 x 1 Two, Toothed washers E2FQ-X10E1 E2FQ-X10F1 8 Two, clamping nut Two, Toothed washers Note: Oil-resistant, vibration-resistant, and fire-retardant vinyl-insulated round cord, 6 dia. x 3 cores, standard length: 2 m The cord can be extended in an independent conduit for 200 m maximum. Note: Oil-resistant, vibration-resistant, and fire-retardant vinyl-insulated round cord, 6 dia. x 2 cores, standard length: 2 m The cord can be extended in an independent conduit for 200 m maximum. E2FQ-X10D1 57 57 50 42 dia. 50 41 36 42 dia. 38 41 36 38 (see note) (see note) Indicator M30 x 1.5 8 Indicator Two, clamping nut M30 x 1.5 Two, Toothed washers Note: Oil-resistant, vibration-resistant, and fire-retardant vinyl-insulated round cord, 6 dia. x 3 cores, standard length: 2 m The cord can be extended in an independent conduit for 200 m maximum. 8 Two, clamping nut Two, Toothed washers Note: Oil-resistant, vibration-resistant, and fire-retardant vinyl-insulated round cord, 6 dia. x 2 cores, standard length: 2 m The cord can be extended in an independent conduit for 200 m maximum. Mounting Holes Model F 4 F (mm) E2FQ-X2# 12.5 mm dia. E2FQ-X5# 18.5 mm dia. E2FQ-X10# 30.5 mm dia. +0.5 0 +0.5 0 +0.5 0 Inductive Sensors E2FQ 5 WARRANTY OMRON’s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON’S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. SUITABILITY FOR USE THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED. THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please refer to separate catalogs for OMRON's safety rated products. OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer’s application or use of the product. At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Cat. No. D029-E2-05A-X • Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. • Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. • Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PERFORMANCE DATA Performance data given in this document is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user’s programming of a programmable product, or any consequence thereof. In the interest of product improvement, specifications are subject to change without notice. OMRON EUROPE B.V. Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands Phone: +31 23 568 13 00 Fax: +31 23 568 13 88 www.industrial.omron.eu 6 Inductive Sensors