Resin-case Proximity Sensor
E2F
D29I-E-01
Proximity Sensor with Resin Case
with Superb Water Resistance
• Rugged, watertight plastic housing offers good chemical
resistance and withstands washdown; IP68 protection
• Wide operating voltages: 10 to 30 VDC and 20 to 264 VAC
• Operation indicator on all models
• Short-circuit protection available on all DC and some AC
models
• Mutual interference prevention with models with different
frequencies is also available.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Be sure to read Safety Precautions on
page 5.
Ordering Information
Sensors [Refer to Dimensions on page 6.]
Model
Sensing distance
Model
Operation mode
Output configuration
NO
M8
Shielded
M12
M18
M30
1.5 mm
2 mm
5 mm
10 mm
NC
DC 3-wire, NPN
E2F-X1R5E1 2M
E2F-X1R5E2 2M
AC 2-wire
E2F-X1R5Y1 2M
E2F-X1R5Y2 2M
DC 3-wire, NPN
E2F-X2E1 2M *1
E2F-X2E2 2M *1
AC 2-wire
E2F-X2Y1 2M *1
E2F-X2Y2 2M *1
DC 3-wire, NPN
E2F-X5E1 2M *1
E2F-X5E2 2M *1
AC 2-wire
DC 3-wire, NPN
*1
E2F-X5Y1 2M *2
E2F-X10E1 2M *1
E2F-X10E2 2M *1
AC 2-wire
*1
E2F-X10Y1 2M *2
E2F-X10Y2 2M *2
*1
E2F-X5Y2 2M *2
*1
*1. Models with different frequencies are also available. The model numbers are E2F-X@@@5 (e.g., E2F-X5E15).
*2. Models are also available with short-circuit protection. The model numbers are E2F-X@Y@-53 (e.g., E2FX5Y1-53). The power supply voltage, however, is 100 to 120 VAC.
1
E2F
Ordering Information
Accessories (Order Separately)
Protective Covers
Refer to Y92@ for details.
Mounting Brackets
Special resin mounting sleeves: Four different models available.
Simply select the size that fits the outside diameter of the Sensor.
Mounting Bracket Dimensions
A
Item
B
Model
E
G
F
D
C
Y92E-B8
Y92E-B12
Y92E-B18
Y92E-B30
Dimension (mm)
A
B
C
D
E
18±0.2
24±0.2
32±0.2
45±0.2
10 max.
12.5 max.
17 max.
17 max.
18
20
30
50
8 dia.
12 dia.
18 dia.
30 dia.
28 max.
37 max.
47 max.
60 max.
F
6
6
7
10
Applied Applicable
hexagonal
Sensor
G
bolts
diameter
7.4 dia. M4 × 20
M8
8 dia.
M4 × 25
M12
9.8 dia. M5 × 32
M18
9.8 dia. M5 × 50
M30
Note: Consider the influence of surrounding metal when mounting non-shielded Sensors. (Refer to
information on individual Sensors for dimensions.)
Material:
Mounting Bracket: Polyacetal
Hexagonal bolt and spring washer: Nickel-plated iron
Nut Sets
These nut sets are for mounting the Sensors. Order them if you lose the mounting nuts
supplied with the sensor. Order the correct set for the outer diameter of your Sensor.
Model
Item
Applicable Sensor
Y92E-NWM12-E2F
Applicable Sensor diameter
Set contents
M8
Y92E-NWM08-E2F
E2F
M12
Y92E-NWM18-E2F
M18
Y92E-NWM30-E2F
M30
Clamping nuts (polyacetal): 2
2
E2F
Ratings and Specifications
Model
Item
E2F-X1R5E@
E2F-X1R5Y@
E2F-X2E@
E2F-X2Y@
E2F-X5E@
E2F-X5Y@
E2F-X10E@
E2F-X10Y@
Sensing distance
1.5 mm ±10%
2 mm ±10%
5 mm ±10%
10 mm ±10%
Set distance
0 to 1.2 mm
0 to 1.6 mm
0 to 4 mm
0 to 8 mm
Differential travel
10% max. of sensing distance
Detectable object
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 3.)
Standard sensing
object
Iron, 8 × 8 × 1 mm
Iron, 12 × 12 × 1 mm
Iron, 18 × 18 × 1 mm
Iron, 30 × 30 × 1 mm
Response frequency
*1
E Models: 2 kHz,
Y Models: 25 Hz
E Models: 1.5 kHz,
Y Models: 25 Hz
E Models: 600 Hz,
Y Models: 25 Hz
E Models: 400 Hz,
Y Models: 25 Hz
Power supply voltage
(operating voltage
range)
E Models: 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Y Models: 24 to 240 VAC (20 to 264 VAC)
Current consumption
E Models: 17 mA max.
Leakage current
Y Models: 1.7 mA max. at 200 VAC (Refer to Engineering Data on page 3.)
Control
output
Load
current
E Models: 200 mA max.
Y Models: 5 to 100 mA
E Models: 200 mA max.
Y Models: 5 to 300 mA
Residual
voltage
E Models: 2 V max. (Load current: 200 mA, Cable length: 2 m)
Y Models: Refer to Engineering Data on page 4.
Indicators
E1 Models: Detection indicator (red), E2 Models: Operation indicator (red)
Y Models: Operation indicator (red)
Operation mode
(with sensing object
approaching)
E1/Y1 Models: NO Refer to the timing charts under I/O Circuit Diagrams on page 4 for details.
E2/Y2 Models: NC
Protection circuits
E Models: Reverse polarity protection, Load short-circuit protection, Surge suppressor; Y Models: None
Ambient
temperature range
Operating/Storage: −25 to 70°C (with no icing or condensation)
Ambient
humidity range
Operating/Storage: 35% to 95%
Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C
Voltage influence
E Models: ±2.5% max. of sensing distance at rated voltage in rated voltage ±15% range
Y Models: ±1% max. of sensing distance at rated voltage in rated voltage ±10% range
Insulation resistance
50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength
E Models:
1,000 VAC, 50/60 Hz for 1 min between current-carrying parts and case
Y Models: (M8 Models): 2,000 VAC, 50/60 Hz for 1 min between current-carrying parts and case
(Other M8 Models):
4,000 VAC, 50/60 Hz for 1 min between current-carrying parts and case
Vibration resistance
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance
Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection
IEC 60529 IP68, in-house standards: oil-resistant *2
Connection method
Pre-wired Models (Standard cable length: 2 m)
Weight (packed state)
Approx. 40 g
Approx. 50 g
Approx. 130 g
Approx. 170 g
Case
Sensing
Materials surface
Clamping
nuts
Accessories
Polyarylate resin
Polyacetal
Instruction manual
*1. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and
a set distance of half the sensing distance.
*2. When using the Sensor in environments subject to splashing cutting oil, deterioration may result due to the additives in the oil. The E2E is recommended in such
environments.
OMRON Test Method
Usage conditions: 10 m or less under water in natural conditions
1. No water ingress after 1 hour under water at 2 atmospheres of pressure.
2. Sensing distance and insulation resistance specifications must be met after 20 repetitions of 1 hour in 0°C water and 1 hour in 70°C water.
3
E2F
Engineering Data (Reference Value)
Sensing Area
Leakage Current
E2F-X@Y@
10
E2F-X2
E2F-X10
Y
X
E2F-X1R5
E2F-X5
Leakage current (mA)
2
E2F-X5@@/-X10@@
Distance X (mm)
Distance X (mm)
E2F-X1R5@@/-X2@@
2.0
Protective resistance
mA
V
1.5
AC power
50/60 Hz
Proximity
Sensor (OFF)
5
1
1.0
Y
X
0
−6
0
−15
−2
0
2
4
6
E2F-X1R5 Sensing Head
E2F-X2 Sensing Head
Distance Y (mm)
−4
−5
0
5
10
15
E2F-X5 Sensing Head
E2F-X10 Sensing Head
Distance Y (mm)
−10
0
50
100
150
200
250
Power supply voltage (V)
Influence of Sensing Object Size and Material
2.5
d×
d
X
E2F-X2@@
Distance X (mm)
Distance X (mm)
E2F-X1R5@@
t = 1 mm
2.0
Iron
1.5
2.4
2.2
d×
d
X
2
t = 1 mm
1.8
Iron
Stainless steel
(SUS304)
1.6
1.4
Stainless steel
(SUS304)
1.2
1
1.0
Brass
0.5
Brass
0.8
0.6
Aluminum
Aluminum
0.4
0.2
5
10
15
20
25
Side length of sensing object: d (mm)
Distance X (mm)
E2F-X5@@
7
d×
d
X
6
0
5
10
15
20
25
Side length of sensing object: d (mm)
E2F-X10@@
t = 1 mm
Iron
5
4
Stainless steel (SUS304)
3
Distance X (mm)
0
12
11
10
d×
d
X
2
Aluminum
1
Iron
9
8
Stainless steel (SUS304)
7
6
5
Brass
t = 1 mm
Brass
4
3
Aluminum
2
1
0
5
10
15
20 25 30 35 40 45 50
Side length of sensing object: d (mm)
0
10
20
30
40
50
60
Side length of sensing object: d (mm)
4
E2F
Residual Output Voltage
30
25
20
Residual Output
Voltage
15
10
0
Residual
Load
Voltage
1
3
5
10
30
Residual output voltage
100
ON
80
V
60
240
Residual output voltage
200
ON
160
V
120
VL
VL
100 VAC
A
40
VL
200 VAC
A
80
24 VAC
A
5
120
ON
V
E2F-X@Y@ at 200 VAC
Load voltage VL (V)
E2F-X@Y@ at 100 VAC
Load voltage VL (V)
Load voltage VL (V)
E2F-X@Y@ at 24 VAC
20
OFF
50 100
300 500
Load current (mA)
0
40
Residual
load
voltage
1
3
5
10
30
OFF
50 100
300 500
Load current (mA)
0
Residual
load
voltage
1
3
5
10
30
50
OFF
100
300 500
Load current (mA)
I/O Circuit Diagrams
Output configuration
Operation
mode
Model
Timing chart
NO
E2F-X1R5@
Present
Sensing object
E2F-X1R5E1
E2F-X2E1
E2F-X5E1
E2F-X10E1
Output circuit
Not present
Load (between brown
and black leads)
Brown
Operate
Reset
Output voltage (between
black and blue leads)
High
Low
ON
Detection indicator (red)
OFF
+V
330 Ω
Load
Proximity
Sensor
main
circuit
4.7 kΩ
Black
*1
Output
*2
Tr
Blue
0V
*1. Load current: 200 mA max.
*2. When a transistor is connected.
DC 3-wire
Sensing object
NC
E2F-X1R5E2
E2F-X2E2
E2F-X5E2
E2F-X10E2
Present
Except the E2F-X1R5@.
Not present
Load (between brown
and black leads)
Output voltage (between
black and blue leads)
Detection indicator (red)
Brown
Operate
Reset
High
Low
ON
OFF
+V
100 Ω
Load
Proximity
Sensor
main
circuit
4.7 kΩ
Black
2.2 Ω
*1
Output
*2
Tr
Blue
0V
*1. Load current: 200 mA max.
*2. When a transistor is connected.
NO
E2F-X1R5Y1
E2F-X2Y1
E2F-X5Y1
E2F-X10Y1
Present
Sensing object
Not present
Operate
Load
Reset
Operation
indicator (red)
OFF
AC 2-wire
NC
E2F-X1R5Y2
E2F-X2Y2
E2F-X5Y2
E2F-X10Y2
Sensing object
Brown
ON
Present
Load
Proximity
Sensor
main
circuit
Blue
Not present
Load
Operation indicator
(red)
Operate
Reset
ON
OFF
5
E2F
Safety Precautions
Refer to Warranty and Limitations of Liability.
WARNING
● Mounting
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Do not tighten the nut with excessive force.
Model
Precautions for Correct Use
Do not use this product under ambient conditions that exceed the
ratings.
E2F-X1R5@@
E2F-X2@@
E2F-X5@@
E2F-X10@@
Torque
0.78 N·m
2 N·m
● Maintenance and Inspection
● Design
Influence of Surrounding Metal
When mounting the Sensor within a metal panel, ensure that the
clearances given in the following table are maintained. Failure to
maintain these distances may cause deterioration in the performance
of the Sensor.
Do not use AC 2-Wire Models in water or in locations subject to water
if the sensing surface or any other part of the Sensor is damaged,
e.g., from contact with the sensing object. Electric shock may result.
l
n
m
φd
D
m
l
(Unit: mm)
Influence of Surrounding Metal
Model
Item
l
d
D
8
E2F-X1R5@@
E2F-X2@@
12
0
E2F-X5@@
0
18
30
E2F-X10@@
m
n
4.5
12
8
18
20
27
40
45
Mutual Interference
When installing Sensors face-to-face or side-by-side, ensure that the
minimum distances given in the following table are maintained.
B
A
(Unit: mm)
Mutual Interference
Model
E2F-X1R5@@
E2F-X2@@
E2F-X5@@
E2F-X10@@
Item
A
B
20
30 (20)
50 (30)
100 (50)
15
20 (12)
35 (18)
70 (35)
Note: Values in parentheses apply to Sensors operating at different
frequencies. Models numbers for Sensors with different frequencies are
E2F-X@@@5.
6
E2F
(Unit: mm)
Dimensions
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
DC 3-Wire Models
AC 2-Wire Models
E2F-X1R5E@
E2F-X1R5Y@
30
22
15 dia.
20
13
M8 × 1
29
13
*
Detection indicator (red)
Two clamping nuts
Two washers
4
40
32
15 dia.
M8 × 1
* 3.5-dia. vinyl-insulated round cable with 3
conductors (Conductor cross section: 0.14 mm2,
Insulator diameter: 1 mm), Standard length: 2 m
The cable can be extended up to 200 m
(separate metal conduit).
E2F-X2E@
4
Operation indicator (red)
Two clamping nuts
*
Two washers
* 3.5-dia. vinyl-insulated round cable with 2
conductors (Conductor cross section: 0.14 mm2,
Insulator diameter: 1 mm), Standard length: 2 m
The cable can be extended up to 200 m
(separate metal conduit).
E2F-X2Y@
43
38
27
32
24
17
29
17
*
M12 × 1
Detection indicator (red)
Two clamping nuts
4
M12 × 1
* 6-dia. vinyl-insulated round cable with 2 conductors (Conductor
cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard
length: 2 m
The cable can be extended up to 200 m (separate metal conduit).
* 6-dia. vinyl-insulated round cable with 3 conductors (Conductor
cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard
length: 2 m
The cable can be extended up to 200 m (separate metal conduit).
E2F-X5E@
4
*
Operation indicator (red)
Two clamping nuts
E2F-X5Y@
47
40
32
24
47
40
32
24
29
29
*
*
Detection indicator (red)
M18 × 1
4
Operation indicator (red)
M18 × 1
Two clamping nuts
* 6-dia. vinyl-insulated round cable with 3 conductors (Conductor
cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard
length: 2 m
The cable can be extended up to 200 m (separate metal conduit).
E2F-X10E@
Two clamping nuts
4
* 6-dia. vinyl-insulated round cable with 2 conductors (Conductor
cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard
length: 2 m
The cable can be extended up to 200 m (separate metal conduit).
E2F-X10Y@
57
50
57
50
41
41
36
36
38
38
*
M30 × 1.5
*
Detection indicator (red)
M30 × 1.5
Two clamping nuts
5
* 6-dia. vinyl-insulated round cable with 3 conductors (Conductor
cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard
length: 2 m
The cable can be extended up to 200 m (separate metal conduit).
Operation indicator (red)
5
Two clamping nuts
* 6-dia. vinyl-insulated round cable with 2 conductors (Conductor
cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard
length: 2 m
The cable can be extended up to 200 m (separate metal conduit).
Mounting Hole Dimensions
Model
F (mm)
E2F-X1R5@@
8.5 +0.5
dia.
0
E2F-X2@@
12.5 +0.5
dia.
0
E2F-X5@@
18.5 +0.5
dia.
0
E2F-X10@@
+0.5
30.5 0 dia.
F
7
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change without notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the importation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security interest in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original transportation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
14.
15.
16.
17.
18.
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for published information.
Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or settle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
Property; Confidentiality. Any intellectual property in the Products is the exclusive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law principles). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability. If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Companies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this Product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
2.
3.
4.
5.
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.55.59.01.43.00 • 01-800-226-6766 • mela@omron.com
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • mela@omron.com
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu
Authorized Distributor:
Automation Control Systems
• Machine Automation Controllers (MAC) • Programmable Controllers (PLC)
• Operator interfaces (HMI) • Distributed I/O • Software
Drives & Motion Controls
• Servo & AC Drives • Motion Controllers & Encoders
Temperature & Process Controllers
• Single and Multi-loop Controllers
Sensors & Vision
• Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors
• Amplified Photomicrosensors • Measurement Sensors
• Ultrasonic Sensors • Vision Sensors
Industrial Components
• RFID/Code Readers • Relays • Pushbuttons & Indicators
• Limit and Basic Switches • Timers • Counters • Metering Devices
• Power Supplies
Safety
• Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety
Controllers • Light Curtains • Safety Relays • Safety Interlock Switches
D29I-E-01
10/15
Note: Specifications are subject to change.
Printed on recycled paper.
© 2015 Omron Electronics LLC
Printed in U.S.A.