E2Q2-N15Y4-51

Rectangular Proximity Sensor E2Q2 CSM_E2Q2_DS_E_3_1 Change the Sensing Direction Freely • Change the sensing direction from front to back. Adjustable up, down, left and right, in 90° units. • Mounts like a Limit Switch. Be sure to read Safety Precautions on page 5. Ordering Information Sensors DC Models Appearance Model Output configuration Output configuration NPN NO + NC (both outputs) PNP NO + NC (both outputs) Sensing distance Shielded 20 mm Unshielded 30 mm E2Q2-N20E3-H E2Q2-N20F3-H E2Q2-N30ME3-H E2Q2-N30MF3-H AC Models Appearance Sensing distance Model Operation mode NO/NC (selectable) 15 mm E2Q2-N15Y4-H Shielded Unshielded E2Q2-N30MY4-H 30 mm Accessories (Order Separately) The recommended cable clamp is the ST Model manufactured by K.MECS Co., Ltd. Product number ST-M20 × 1.5 Screw size M20 × 1.5 SW 25 C 37 D 9 Applicable cable outer diameter 7 to 13 Applicable seal packing GPM20 SW C D PG For purchasing details, contact the sales company. Contact information is provided below. K.MECS Co.,Ltd. Yusen Iwamotocho Bldg. 3F 2-3-3 Iwamotocho, Chiyodaku, Tokyo, Japan 101-0032. Telephone:+81-3-5825-5333 Facsimile: +81-3-5825-8550 1 E2Q2 Ratings and Specifications Shielding Item Model Sensing distance Set distance Differential travel Sensing object Standard sensing object Response frequency Power supply voltage (operating voltage range) Current consumption/ Leakage current Switching capacity Control output Residual voltage Indicators Operation mode (with sensing object approaching) Protection circuits Ambient temperature Ambient humidity Shielded Temperamodel ture Unshielded influence model Voltage influence Insulation resistance Dielectric strength Vibration resistance (destruction) Shock resistance (destruction) Degree of protection Connection method Weight Case Terminal Materials block Sensing surface Shielded Unshielded Shielded Unshielded E2Q2-N20@3-H E2Q2-N30M@3-H E2Q2-N15Y4-H E2Q2-N30MY4-H 20 mm±10% 30 mm±10% 15 mm±10% 30 mm±10% 0 to 16 mm 0 to 24 mm 0 to 12 mm 0 to 24 mm 15% max. of sensing distance Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 3.) Iron, 60 × 60 × 1 mm Iron, 90 × 90 × 1 mm Iron, 60 × 60 × 1 mm 150 Hz 100 Hz 20 Hz Iron, 90 × 90 × 1 mm 12 to 48 VDC (10 to 60 VDC), ripple (p-p): 10% max. 24 to 240 VAC (20 to 253 VAC), 50/60 Hz 20 mA max. 1.7 mA max Refer to Engineering Data on page 3. 200 mA max. 8 to 500 mA 3 V max. with a 200 mA load current Refer to Engineering Data on page 3. Power indicator (green) Power indicator (green) Detection indicator (yellow) Operation indicator (yellow) E3 Models: NPN NO+NC AC: NO or NC (selectable) F3 Models: PNP NO+NC Refer to the timing charts under I/O Circuit Diagrams Refer to the timing charts under I/O Circuit Diagrams on page 4 for details. on page 4 for details. Reverse polarity protection, load short-circuit --protection Operating: −25 to 70°C (with no icing or condensation) Storage: −40 to 70°C (with no icing or condensation) Operating: 35% to 85% (with no condensation) Storage: 35% to 95% (with no condensation) ±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C ±15% max. of sensing distance at 23°C in the temperature range of −25 to 70°C ±2% max. of sensing distance at within a range of ±10% of rated power supply voltage 50 MΩ min. (at 500 VDC) between current-carrying parts and case E@ Model and F@ Model: 1,000 VAC, 50/60 Hz for 1 min. between current-carrying parts and case Y Model: 4,000 VAC, 50/60 Hz for 1 min. between current-carrying parts and case 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions 500 m/s2 10 times each in X, Y, and Z directions IEC IP67 * Terminal block Approx. 240 g Polybutylene terephthalate (PBT) Polybutylene terephthalate (PBT) Polybutylene terephthalate (PBT) * When the recommended cable clamp is used. 2 E2Q2 Engineering Data (Reference Value) 35 Y X 30 25 35 30 Y 25 20 X 20 Leakage current (mA) Leakage Current E2Q2-N@Y4-H Unshielded Models E2Q2-N30M@@-H Distance X (mm) Distance X (mm) Sensing Area Shielded Models E2Q2-N20@3-H E2Q2-N15Y4-H E2Q2-N20 2.0 1.5 1.0 15 15 E2Q2-N15 10 10 5 5 0 −40 0 −40 Protective resistance mA 0.5 AC power 50/60 Hz V −30 −20 −10 0 10 20 30 40 Distance Y (mm) Sensing Head Proximity Sensor (output OFF) −30 −20 −10 0 10 20 Sensing Head 30 X t = 1 mm Iron 20 15 20 t = 1 mm Iron 15 Stainless steel (SUS304) 10 200 35 Aluminum X 30 300 t = 1 mm Iron 25 Stainless steel (SUS304) Aluminum Brass Brass Copper 10 5 Copper 250 @d 15 Brass 5 150 20 Stainless steel (SUS304) Aluminum 10 100 E2Q2-N30M@@-H @d X 50 Power supply voltage (V) Distance X (mm) @d Distance X (mm) Distance X (mm) Influence of Sensing Object Size and Material E2Q2-N20@3-H E2Q2-N15Y4-H 25 0 40 Distance Y (mm) Copper 5 10 20 30 40 50 60 70 0 10 Side length of sensing object d (mm) 25 20 Residual output voltage ON 30 40 E2Q2-N@Y4-H Load voltage (V) Load voltage (V) Residual Output Voltage E2Q2-N@Y4-H at 24 VAC 20 50 at 100 VAC 100 ON Residual output voltage 80 24 VAC A 5 OFF 30 50 100 300 500 1,000 Load current (mA) 0 100 VAC A 40 20 10 40 60 80 100 Side length of sensing object d (mm) E2Q2-N@Y4-H at 200 VAC 250 200 Residual output voltage ON V 60 10 0 20 150 V V 0 70 120 15 Residual load voltage 3 5 60 Side length of sensing object d (mm) Load voltage (V) 0 100 200 VAC A 50 Residual load voltage 3 5 Residual load voltage OFF 10 30 50 100 300 500 1,000 Load current (mA) 0 3 5 10 30 50 100 OFF 300 500 1,000 Load current (mA) 3 E2Q2 I/O Circuit Diagrams NPN Operation mode Models Timing charts Output circuits NO Present Not present Detection indicator ON (yellow) OFF Sensing object NO+NC E2Q2-N20E3-H E2Q2-N30ME3-H Control output 1 Load Load 4 ON OFF NC Sensing object Present Proximity Sensor main circuit NO output 2 NC output Not present Detection indicator ON (yellow) OFF Control output +V 3 ON OFF 0V PNP Operation mode Models Timing charts Output circuits NO Present Not present Detection indicator ON (yellow) OFF Sensing object NO+NC E2Q2-N20F3-H E2Q2-N30MF3-H Control output 1 ON OFF NC Present Not present Detection indicator ON (yellow) OFF Sensing object Control output Proximity Sensor main circuit +V NO output 4 NC output 2 Load Load ON OFF 3 0V AC Operation mode Models Timing charts Output circuits NO Present Not present Detection indicator ON (yellow) OFF ON Control output OFF Sensing object NO/NC E2Q2-N15Y4-H E2Q2-N30MY4-H 3 NO output NC Sensing object Present Not present Detection indicator ON (yellow) OFF Control output ON OFF 4 Load 1 Load Proximity Sensor main circuit NC output 2 Note: Connect either NO or NC. 4 E2Q2 Safety Precautions ● Mounting Changing the sensing surface direction. WARNING This product is not designed or rated for ensuring safety of persons. Do not use it for such purposes. 1. Remove the 2 screws on the back of the Sensor. Precautions for Safe Use 2. Removing part A allows the sensing surface position to be changed to the front or sides of the Sensor. Precautions for Compliance with UL Standards The product is compliant with UL standards. To meet the requirements for the standards, however, metal connectors or conduits must not be used. When using for UL applications, be sure to use a UL-listed cable clamp. Part A Precautions for Correct Use Do not use this product under ambient conditions that exceed the ratings. ● Design Power Reset Time The Sensor is ready to operate 300 ms after the Sensor is turned ON. If the load and Sensor are connected to independent power supplies respectively, be sure to turn ON the Sensor before supplying power to the load. Influence of Surrounding Metal When mounting the Sensor within a metal panel, ensure that the clearances given in the following table are maintained. A B 3. When positioning the sensing surface to the side, rotate it to the required position, then fit it into the case. The possible positions are 0, 90, 180, and 270°. Do not forcefully rotate the sensing surface. 4. Secure part A with the screws. Part A C B D (Unit: mm) Model Item E2Q2-N@@@-H E2Q2-N@M@@-H A 0 15 B 10 25 C 0 25 D 40 40 Mutual Interference When installing Sensors face-to-face or side-by-side, ensure that the minimum distances given in the following table are maintained. Face-to-face ● Operating Environment Ambient Atmosphere Do not install the product in the following locations. Doing so may result in product failure or malfunction. 1. Locations subject to corrosive gas. 2. Locations subject to shock or vibration. 3. Locations subject to exposure to water, oil, or chemicals. Parallel A B (Unit: mm) Model Item E2Q2-N@@@-H E2Q2-N@M@@-H A 170 280 B 100 200 5 E2Q2 (Unit: mm) Dimensions Unless otherwise specified, the tolerance class IT16 is used for dimensions in this data sheet. Sensors Sensing surface (front) 58.4 Two, 5.3-dia. mounting holes Detection indicator (yellow)* Mounting Hole Dimensions Two, 5.3-dia. , length 1.5 mounting holes 30±0.2 30 40 40 46.5 60±0.2 60 118 Sensing surface (side) Power indicator (green) *AC models have a yellow operation indicator. Conduit screw size, M20 × 1.5 11 16.3 26.5 In the interest of product improvement, specifications are subject to change without notice. 6 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2013.12 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2013 All Right Reserved.