Thin, Compact, Cylindrical Photoelectric Sensor
E3HF/E3HS/E3HT/E3HC
CSM_E3HF_E3HS_E3HT_E3HC_DS_E_4_1
• Cylindrical models (E3HT and E3HC) are ideal for embedded
installation.
• Square 7.5-mm model (E3HS) has a sensing distance of 1 m.
• Resin-filled models (E3HS and E3HC) offer excellent vibration
resistance.
• Ultra-thin 7-mm model (E3HF) requires very little depth for
installation, helping to save space.
• E3HTand E3HC comply with EN standards.
Be sure to read Safety Precautions
on page 6.
Ordering Information
Sensors
Sensing Method
Infrared light
Appearance
Sensing distance
Through-beam *
Diffuse-reflective
700 mm
50 mm
Through-beam *
Diffuse-reflective
1m
50 mm
Through-beam *
Diffuse-reflective
1m
35 mm
Through-beam *
Diffuse-reflective
1m
35 mm
Model
Light- ON
E3HF-1E1
Emitter E3HF-1L
Receiver E3HF-1DE1
Dark-ON
E3HF-1E2
Emitter E3HF-1L
Receiver E3HF-1DE2
E3HF-DS5E1
E3HF-DS5E2
E3HS-1E1
Emitter E3HS-1L
Receiver E3HS-1DE1
E3HS-1E2
Emitter E3HS-1L
Receiver E3HS-1DE2
E3HS-DS5E1
E3HS-DS5E2
E3HT-1E1
Emitter E3HT-1L
Receiver E3HT-1DE1
E3HT-1E2
Emitter E3HT-1L
Receiver E3HT-1DE2
E3HT-DS3E1
E3HT-DS3E2
E3HC-1E1
Emitter E3HC-1L
Receiver E3HC-1DE1
E3HC-1E2
Emitter E3HC-1L
Receiver E3HC-1DE2
E3HC-DS3E1
E3HC-DS3E2
* Through-beam Sensors are normally sold in sets that include both the Emitter and Receiver.
Orders for individual Emitters and Receivers are accepted.
1
E3HF/E3HS/E3HT/E3HC
Accessories
Slits
Slit width
0.5 mm × 4 mm
1 mm × 4 mm
2 mm × 4 mm
Sensing distance Minimum detectable object (typical)
Quantity
Remarks
0.5-mm dia.
120 mm
1 slit each for the
Seal-type long slit
1-mm dia.
Emitter and Receiver Provided with the E3HF200 mm
(6 slits total)
1E@ Through-beam Sensor.
2-mm dia.
400 mm
Mounting Brackets
Appearance
Model
Quantity
Remark
E39-L101
1
Provided with the E3HS
E39-L84
1
Provided with the E3HC
Note: When using through-beam models, order one
bracket for the Receiver and one for the Emitter.
Ratings and Specifications
E3HF/E3HS
Sensing method
Item
Through-beam
Model
E3HF-1E@
Diffuse-reflective
Through-beam
E3HF-DS5E@
E3HS-1E@
50 mm
(White paper 30 × 30 mm)
Diffuse-reflective
E3HS-DS5E@
50 mm
(White paper 30 × 30 mm)
Sensing distance
700 mm
Standard sensing object
Opaque, 3.7-mm dia. min.
---
Opaque, 5.1-mm dia. min.
---
---
20% max. of sensing distance
---
20% max. of sensing distance
Differential travel
1m
Directional angle
Emitter/Receiver: 3 to 20°
each
Light source (wavelength)
Infrared LED (950 nm)
Power supply voltage
12 to 24 VDC ±10%, ripple (p-p): 10% max.
Current consumption
Emitter/Receiver: 20 mA
max.
Control output
Load power supply voltage: 24 VDC max., Load current: 80 mA (residual voltage: E3HF: 1 V max., E3HS: 1.2 V max.)
NPN voltage output type
Light-ON/Dark-ON (depends on model)
Protection
Reverse polarity protection, Reverse polarity protection,
Reverse polarity protection, Reverse polarity protection,
Output short-circuit
Output short-circuit protection, Output short-circuit
Output short-circuit protection,
protection
Mutual interference prevention protection
Mutual interference prevention
Response time
Operate or reset: 5 ms max. Operate or reset: 3 ms max.
each
each
Sensitivity adjustment
---
---
30 mA max.
Emitter/Receiver: 3 to 25°
each
Emitter/Receiver: 20 mA
max.
One-turn adjuster
---
Incandescent lamp: 3,000 lx, Sunlight 10,000 lx
Ambient temperature
Operating: −25 to 55°C, Storage: −30 to 70°C (with no icing or condensation)
Ambient humidity
Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance
20 MΩ min. at 500 VDC
Dielectric strength
500 VAC at 50/60 Hz for 1 minute
Vibration resistance
(destruction)
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance
(destruction)
500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection
IEC IP64
Connection method
Pre-wired models (standard length: 2 m)
Weight (packed state)
Approx. 110 g
MaLens
terial
Mounting Brackets
Accessories
30 mA max.
Operate or reset: 5 ms max. Operate or reset: 3 ms max.
each
each
Ambient illuminance
(Receiver side)
Case
---
One-turn adjuster
IEC IP65
Approx. 70 g
Approx. 120 g
Approx. 80 g
Stainless steel (SUS304)
ABS
Methacrylic resin
Slit (0.5-mm, 1-mm, 2-mm
widths), Instruction sheet
---
Stainless steel (SUS304)
Screwdriver for adjustment,
Instruction sheet
Mounting Bracket (with
screws), Stoppers,
Instruction sheet
Mounting Bracket (with
screws), Screwdriver for
adjustment, Stoppers,
Instruction sheet
2
E3HF/E3HS/E3HT/E3HC
E3HT/E3HC
Sensing method
Item
Through-beam
Model
E3HT-1E@
Diffuse-reflective
Through-beam
E3HT-DS3E@
E3HC-1E@
35 mm
(White paper 30 × 30 mm)
Diffuse-reflective
E3HC-DS3E@
35 mm
(White paper 30 × 30 mm)
Sensing distance
1m
Standard sensing object
Opaque, 6.25-mm dia. min.
---
Differential travel
---
20% max. of sensing distance
Directional angle
Emitter/Receiver: 10 to 25°
each
Light source (wavelength)
Infrared LED (950 nm)
Power supply voltage
12 to 24 VDC ±10%, ripple (p-p): 10% max.
Current consumption
Emitter: 25 mA max.
Receiver: 15 mA max.
Control output
Load power supply voltage: 24 VDC max., Load current: 80 mA (Residual voltage: 1 V max.)
NPN open collector output type
Light-ON/Dark-ON (depends on model)
Protection
Reverse polarity protection,
Output short-circuit
protection
Reverse polarity protection,
Reverse polarity protection,
Output short-circuit protection,
Output short-circuit
Mutual interference
protection
prevention
Reverse polarity protection,
Output short-circuit protection,
Mutual interference
prevention
Response time
Operate or reset: 5 ms max.
each
Operate or reset: 3 ms max.
each
Operate or reset: 3 ms max.
each
Ambient illuminance
(Receiver side)
Incandescent lamp: 3,000 lx, Sunlight 10,000 lx
Ambient temperature
Operating: −25 to 55°C, Storage: −30 to 70°C (with no icing or condensation)
Ambient humidity
Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance
20 MΩ min. at 500 VDC
Dielectric strength
500 VAC at 50/60 Hz for 1 minute
Vibration resistance
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance
Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection
IEC IP66
Connection method
Pre-wired models (standard length: 2 m)
Weight (packed state)
Approx. 130 g
Material
Brass
Lens
Methacrylic resin
Opaque, 6.25-mm dia. min.
---
---
20% max. of sensing distance
Emitter/Receiver: 10 to 25°
each
--Infrared LED (940 nm)
30 mA max.
---
Infrared LED (950 nm)
Infrared LED (940 nm)
Emitter: 25 mA max.
Receiver: 15 mA max.
30 mA max.
Operate or reset: 5 ms max.
each
Approx. 80 g
Case
Approx. 110 g
Approx. 75 g
Stainless steel (SUS304)
Mounting Brackets
Accessories
1m
---
Stainless steel (SUS304)
Instruction sheet
Mounting bracket (with screws), Instruction sheet
Engineering Data (Typical)
150
100
50
Y
100
Through-beam
E3HS-1E@
Distance Y (mm)
Through-beam
E3HF-1E@
Distance Y (mm)
Distance Y (mm)
Parallel Operating Range
Through-beam
E3HF-1E@
Slit C (2 mm)
80
Slit B (1 mm)
60
40
Y
Y
X
20
0
X
0.3
0.6
0.9
1.2
1.5
Distance X (m)
−50
−100
0
-20
Slit A (0.5 mm)
0.3
X
0.6
0.9
1.2
1.5
Distance X (m)
0.5
1
1.5
2
Distance X (m)
-40
-60
-80
−150
-100
3
E3HF/E3HS/E3HT/E3HC
Distance Y (mm)
Through-beam
E3HT-1E@, E3HC-1E@
200
Y
150
X
100
50
0
0.5
1
1.5
2
Distance X (m)
−50
−100
−150
−200
Sensing object: 30 × 30 mm white paper
Y
X
20
40
60
80
12 Sensing object: 30 × 30 mm white paper
Y
8
X
4
0
100
Diffuse-reflective
E3HT-DS3E@, E3HC-DS3E@
Distance Y (mm)
Diffuse-reflective
E3HS-DS5E@
Distance Y (mm)
Distance Y (mm)
Operating Range
Diffuse-reflective
E3HF-DS5E@
20
40
60
80
10
5
3
0.5
20
30
40
50
Distance
X (mm)
−12
Through-beam
E3HS-1E@
Through-beam
E3HT-1E@, E3HC-1E@
500
300
100
70
50
30
500
300
100
50
30
10
5
3
10
7
5
Operating 1
Level
10
Excess gain ratio (times)
50
30
4
Excess gain ratio (times)
Excess gain ratio (times)
100
X
−8
−12
500
300
Y
8
−4
Distance
X (mm)
−8
Excess Gain vs. Set Distance
Through-beam
E3HF-1E@
Sensing object: 30 × 30 mm white paper
0
100
−4
Distance X (mm)
12
Operating 1
Level
0.5
3
0.3
0.3
0.1
0
0.5
1.0
1.5
Distance (m)
Operating 1
Level 0
0.1
0.5
1.0
1.5
2.0
Distance (m)
0
0.5
1.0
1.5
2.0
2.5
Distance (m)
4
E3HF/E3HS/E3HT/E3HC
10
7
5
3
Operating 1
Level
500
Diffuse-reflective
E3HT-DS3E@, E3HC-DS3E@
Excess gain ratio (times)
Diffuse-reflective
E3HS-DS5E@
Excess gain ratio (times)
Excess gain ratio (times)
Diffuse-reflective
E3HF-DS5E@
Sensing object: 30 × 30 mm white paper
300
100
70
50
30
0.7
0.5
0.3
0.1
0
50
100
150
100
70
50
30
10
7
5
3
10
7
5
Operating
Level 1
3
0.3
0.7
0.5
Operating 1
Level 0
0.1
20
40
60
Distance (mm)
80
100
120
0
20
Distance (mm)
40
60
Distance (mm)
I/O Circuit Diagrams
NPN Output
Model
Operation
mode
E3HF-1E1 *
E3HF-DS5E1
E3HS-1E1 *
E3HS-DS5E1
Light-ON
E3HT-1E1 *
E3HT-DS3E1
Timing charts
Output circuit
Incident light
No incident light
ON
Light
indicator (red) OFF
ON
Output
transistor
OFF
Operate
Load
(e.g., relay)
Reset
Through-beam Receivers, Reflective Sensors
Brown
(Between brown and black)
Output voltage
(e.g., logic)
E3HC-1E1 *
E3HC-DS3E1
E3HF-1E2 *
E3HF-DS5E2
H
L
(Between blue and black)
E3HS-1E2 *
E3HS-DS5E2
Dark-ON
E3HT-1E2 *
E3HT-DS3E2
E3HC-1E2 *
E3HC-DS3E2
Light
indicator
(red)
1.5 to 3 mA
Photoelectric
Sensor
main
circuit
Incident light
No incident light
ON
Light
indicator (red) OFF
ON
Output
transistor
OFF
Operate
Load
(e.g., relay)
Reset
+V
Black Output
ZD
Blue
0V
(Between brown and black)
Output voltage
(e.g., logic)
Through-beam Model Emitters
H
L
(Between blue and black)
Brown
Power
indicator
(red)
Photoelectric
Sensor
main
circuit
12 to 24 VDC
Blue
* Models numbers for Through-beam Sensors (E3H@-1E@) are for sets that include both the Emitter and Receiver.
Emitter model numbers are in the form E3H@-1L (e.g., E3HF-1L). Receiver model numbers are in the form E3H@-1DE@ (e.g., E3HF-1DE1). Refer to Ordering
Information to confirm model numbers for Emitter and Receivers.
5
E3HF/E3HS/E3HT/E3HC
Safety Precautions
WARNIGS
E3HT
• Do not tighten to a torque that exceeds the following values.
This product is not designed or rated for
ensuring safety of persons. Do not use it for
such purpose.
Precautions for Correct Use
Do not use the product in atmospheres or environments that
exceed product ratings.
●Mounting
Mounting
E3HF
• Use flat washers and spring washers on the M3 screws, and
tighten the screws to a torque of 0.29 N·m max.
E3HC
Part B Part A
Note: The allowable torque depends on the distance from the tip of the head.
Refer to the following table for the tightening torque for parts A and B.
(Part A is the range between the tip of the head and the value given in the
table. Part B includes the nut on the head, as shown in the figure above.
If the edge of the nut enters the area of part A even slightly, apply the
torque for part A.)
Torque
Model
Tightening torque: 0.2 N·m max.
Part A
Dimension
Torque
(mm)
E3HT-@@@
Set screw
(indentation tip)
12
Part B
Torque
2 N·m
2.9 N·m
●Adjusting
Slit Adjustment
E3HF
• Slits with widths of 0.5, 1.0, and 2.0 mm are provided. Use
these slits for adjustment when the diameter of the sensing
object is 3.7 mm or less, and when it is necessary to correct
for mutual interference.
l
(Unit: mm)
Dimensions
Unless otherwise specified, the tolerance class IT16 is used for dimensions in this data sheet.
Sensors
E3HF-1E@
Emitter
Receiver
R3.5
50
40±0.2
5
3.6
3.6
3.5-dia. vinyl-insulated
Lens (3.7 dia.) round cable with
2 conductors (Conductor
28
cross section:
R0.5
0.15 mm2, Insulator
4.5
diameter: 1.06 mm),
Standard length: 2 m
C2
R3.5
7
3.6
3.5-dia. vinyl-insulated
round cable with
3 conductors (Conductor
cross section:
0.15 mm2, Insulator
diameter: 1.06 mm),
Standard length: 2 m
3.6
Lens (3.7 dia.)
28
R0.5 4.5
C2
28
23
14
8
5
Light indication (red)
Power indicator
(red)
28
50
40±0.2
3.4
3.4
7
Emitter: E3HF-1L
Receiver: E3HF-1DE@
R3.5
R3.5
23
14
4
4
40±0.2
3.4 dia.
3.4 dia.
8
40±0.2
Mounting Holes
Two, M3
40±0.2
Note: Models numbers for Through-beam Sensors (E3HF-1E@) are for sets that include both the Emitter and Receiver.
The Emitter model number is E3HF-1L. Receiver model numbers are in the form E3HF-1DE@ (e.g., E3HF-1DE1). Refer to Ordering Information to confirm model
numbers for Emitter and Receivers.
6
E3HF/E3HS/E3HT/E3HC
E3HF-DS5E@
50
40±0.2
R3.5
5
R3.5
3.4
7
Sensitivity adjuster
3.6
3.6
Light indicator (red)*
3.5-dia. vinyl-insulated round
cable with 3 conductors
(Conductor cross section:
0.15 mm2,
Insulator diameter:
1.06 mm),
Standard length:
2m
14
Lens
(3.7 dia.)
28
C2
Emitter
5
Mounting Holes
Two, M3
7.5
28
40±0.2
Receiver
3.4 dia.
8
4
10.6
40±0.2
* The indicator is not visible from the lens surface.
E3HS-1E@
With Mounting Bracket R2.05
Attached
10
2
23 15.4 9.4
Mounting Holes
Stainless steel (SUS304)
Light indicator (red)*
4.1
7.5
15.4±0.2
Emitter:
R1.75
Lens (5.1 dia.)
8.8
3.5-dia. vinyl-insulated round cable with 2 conductors
(Conductor cross section: 0.15 mm2, Insulator diameter:
1.06 mm), Standard length: 2 m
Receiver: 3.5-dia. vinyl-insulated round cable, with 3 conductors
(Conductor cross section: 0.15 mm2, Insulator diameter:
1.06 mm), Standard length: 2 m
R2
3.5
7.5
3.75
0.7
*Emitter: Power indicator (red)
40
E3HS-DS5E@
With Mounting Bracket R2.05
Attached
23.6
10
2
Stainless steel (SUS304)
23 15.4 9.4
Mounting Holes
Sensitivity adjuster
Light indicator (red)*
4.1
15.4±0.2
7.5
3.5-dia. vinyl-insulated round cable with 3 conductors
2
R2 (Conductor cross section: 0.15 mm , Insulator diameter: 1.06 mm),
Standard length: 2 m
R1.75
Receiver
8.8
Two, M3
3.5
Two, M3
7.5
3.1
Emitter
0.7
40
E3HT-1E@
13
M8 P=1.0
Emitter: 3.5-dia. vinyl-insulated round cable with 2 conductors
(Conductor cross section: 0.15 mm2, Insulator diameter: 1.06 mm),
Standard length: 2 m
Receiver: 3.5-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.15 mm2, Insulator diameter: 1.06 mm),
Standard length: 2 m
2 washers
(stainless steel)
2 tightening nuts
(brass)
Lens (6.25 dia.)
4
Light indicator (red)*
15
30
40
E3HT-DS3E@
(2.8)
1.15
Receiver
Emitter
1.65
M8 P=1.0
2 washers
(stainless steel)
2 tightening nuts
(brass)
4
1.5±0.5
* Emitter has a power indicator (red).
3.5-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.15 mm2, Insulator diameter: 1.06 mm),
Standard length: 2 m
Light indication (red)*
13
15
30
40
1.5±0.5
Note: Models numbers for Through-beam Sensors (E3H@-1E@) are for sets that include both the Emitter and Receiver.
Emitter model numbers are in the form E3H@-1L (e.g., E3HS-1L). Receiver model numbers are in the form E3H@-1DE@ (e.g., E3HS-1DE1). Refer to Ordering
Information to confirm model numbers for Emitter and Receivers.
7
E3HF/E3HS/E3HT/E3HC
*
E3HC-1E@
Emitter:
3.5-dia. vinyl-insulated round cable with 2 conductors
(Conductor cross section: 0.15 mm2, Insulator diameter:
1.06 mm), Standard length: 2 m
Receiver: 3.5-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.15 mm2, Insulator diameter:
1.06 mm), Standard length: 2 m
With Mounting Bracket Attached
10
Stainless steel (SUS304)
0.4
6.1
Lens
(6.25 dia.)
Two, R1.7
3.4
Mounting Holes
Mounting
bracket
23
16 6.9 dia.
0.6
R1.7
Light indicator (red)*
Four, R2
3.4
7.3
16
*Emitter: Power indicator (red)
40
1.5±0.5
Two, M3
E3HC-DS3E@
With Mounting Bracket Attached
(2.8)
1.15
1.65
10
0.4
Stainless steel (SUS304)
Receiver
6.1
Mounting Holes
3.4
Emitter
Mounting
bracket
3.5-dia. vinyl-insulated round cable with 3 conductors
2
Two, R1.7 (Conductor cross section: 0.15 mm ,
Insulator diameter: 1.06 mm), Standard length: 2 m
23
16 6.9 dia.
0.6
R1.7
16
Light indicator (red)
Four, R2
3.4
7.3
40
1.5±0.5
Two, M3
Note: Models numbers for Through-beam Sensors (E3HC-1E@) are for sets that include both the Emitter and Receiver.
The Emitter model number is E3HC-1L. Receiver model numbers are in the form E3HC-1DE@ (e.g., E3HC-1DE1). Refer to Ordering Information to confirm model
numbers for Emitter and Receivers.
Accessories (Order Separately)
Seal-type Long Slit
(For E3HF-1E@)
+0
5.4 × 5.4 −0.2
A
Oblong hole
L
4
Name
Slit (A)
Slit (B)
Slit (C)
L (mm)
A (mm)
0.5
1
2
0.25
0.5
1
Note: Slits are adhesive and pressure-sensitive.
Peel off the seal, and attach the slit to the lens
surface.
Material: Polyester film
*Provided with the Through-beam E3HF-1E@
Mounting Brackets
In the interest of product improvement, specifications are subject to change without notice.
8
Read and Understand This Catalog
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or
comments.
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)
from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS
IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT
LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the
products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,
machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible
uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or government regulations.
• Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON
Warranty and Limitations of Liability.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
2010.9
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2010 All Right Reserved.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Omron:
E3HC-1DE2 E3HS-1E1 E3HS-DS5E2