F150-M05L

*Lights up in green when power is turned ON. A.Lights up in orange while video signal is being input.. B.Volume for adjusting brightness of backlight Backlight becomes brighter by rotating the volume When using LCD monitor F150-M05L with clockwise and darker by rotating counterclockwise. connecting to F150, F180, or F400 series vision C.Volume for adjusting contrast of screen Contrast becomes larger by rotating the volume sensor, pay attention to the following points. clockwise. 1. Window setting should be made within the D.Connect the power supply of DC24V to this terminal. picture displaying field of this LCD monitor. E.Screen change-over switch 2. If the window is set outside the picture displaying By setting this switch to REV, the screen reverses field, the window cursor or a part of the window vertically and horizontally. F.Change-over switch of video input end resistance (75 (field of 8 lines at the upper portion of the /HIGH) screen) is not displayed. Measurement is still When no cable is connected to the video output possible without any trouble. terminal, keep this switch set to 75 . G.Video input terminal (pin jack) Field of 8 lines at the upper portion of screen of F150 H.Video output terminal (pin jack) Buffering is not made to the composite video output. or F400 video output is not displayed on the screen When using the composite video output of this product of this LCD monitor. by connecting to other instrument, set the switch F to HIGH or separate the end resistance of the instrument If F150-M05L is used by connecting to the vision connected. recognition device (F200, F300, F350 or F381 . Power Supply Connecting Terminal series), the menu characters will come out from the screen. It is not recommended to use them. Power supply connecting terminal is located at the back of To F200, F300, F350, and F381 series, connect the main unit.Connect the power supply unit of DC24V. the monitor F300-M09. 5 NOTICE F150-M05L Model LCD Monitor INSTRUCTION SHEET Thank you for selecting OMRON product. This sheet primarily describes precautions required in installing and operating the product. Before operating the product, read this sheet thoroughly to acquire sufficient knowledge of the product. For your convenience, keep this sheet for your disposal. Dimensions Unit mm Thickness of plate possible to fit 1.6 - 4.8 46max. Metal fitting POWER SYNC 143 145 155 50min 100 185 Monitor cable(RCA/BNC VIDEO CABLE) 42.2 Tolerance: +/-1mm Dimension in ( ) is for reference. 174 Panel cut diagram 3 POWER SYNC DC24V { @ | Protective transparent seal is stuck to front of the screen of F150-M05L. Remove this seal to obtain clear sight. ©OMRON Corporation 1999 All Rights Reserved. Power supply unit DC24V 1. Meaning of Warning indication Warning ++ B Precautions for safety This indicates the case that may contain possibility of death or heavy injury if wrongly handled. Warning 4. Check of package Check if the following articles are complete in the package. Do not open case. Hazardous voltage inside may cause electrical shock. 2.Instruction manual this booklet Power consumption Current consumption 3.Fitting metals or sales office in your city. Component Names Front Back B.Volume BRIGHT *LED indicator POWER NOTE Operating humidity 35 - 85%RH(There should be no dew condensation.) Operating atmosphere There should be no corrosive gas. Storage temperature |25 ` {65 Approx. 1 kg PRECAUTIONS IN USING THE PRODUCT When the product is used under the circumstances below, ensure adherence to the limitations of the ratings and functions. Also, take countermeasures for safety precautions such as fail-safe installations. 1.Use under the circumstances or environment which are not described in the instruction sheet. 2.Use for the equipment which require higher level of safety, such as nuclear devices, railroad, aircrafts, vehicles, combustion devices, amusement machinery, medical equipment, safety devices. 3.Use for applications where death , serious injury or property damage is possible and extensive safety precautions are required. LCD panel BRIGHT For securing safety, be sure to observe the following particulars. (1) Do not use the product in the range exceeding the rated voltage. (2) LCD panel is a glass product. Do not hit or drop it. Otherwise, it will be broken and dangerous. (3) LCD panel contains some irritant substances in it. If LCD panel was broken and liquid substance in it stuck to the skin or entered in the eye, wash out with flowing water and consult the doctor. (4) Do not use the LCD monitor in the place where any substance or water (waterdrop) may enter. (5) Disposal of this product may be regulated by some of local governments. Follow respective local government. Specifications DC24V( 10% A 15%) 15W or less 700 mA or less 10 - 150 Hz one amplitude 0.1 mm Vibration 3 directions 8 min. each, 10 times resistance 2 6 directions each 3 times Shock resistance 150 m/s Operating temperature 0 `50 Weight +0.5mm 175.5 0 Recommended product (OMRON product) Emodel S82K |01524 Emodel S82K |05024 General specifications 1.LCD monitor main unit 2. M3 Crimp-style terminal of within O.D. 5.5 mm should be used. Specifications Item Supply voltage If shortage of article is found, contact our branch Warning +0.5mm 133.5 0 POWER CONTRAST SYNC Display unit C.Volume CONTRAST D.Power supply connecting terminal A.LED indicator SYNC Bottom E.Switch NOR ^REV F.Switch 75 ^HIGH ¶ G.Video input Item Panel size Panel type Resolution Display color Picture pitch Picture size Contrast Angle of visibility Brightness Back wright Response speed Input signal Specifications 5.5 type TFT 320 ~240 dots full color 0.348(H) ~0.348(V)mm 111.36(H) ~83.52(V)mm 85:1(TYP) Vertical 25 degree Horizontal 50 degree (Contrast ratio>10) 250cd/m2 (TYP) Cold cathode fluorescent tube 60 ms or less NTSC composite video (1.0V/75 end) H.Video output OMRON Corporation