G6K-2P-Y

Low Signal Relay G6K • Compact fourth generation design, offers excellent board space savings. • Available in 2.54 and 3.2 mm coil-contact terminal spacing. • “-Y” models meet 2.5 kV Bellcore surge requirements. • Conforms to FCC Part 68. • Terminal design based on Omron’s successful G6S relay. • Available in PCB through-hole, SMT gullwing and SMT “inside-L” terminals. • UL recognized / CSA certified. • Available in single coil latching. • RoHS Compliant. RC Ordering Information To Order: Select the part number and add the desired coil voltage rating (e.g., G6K-2F-DC5). Terminal Contact form Non-latching 2.54 mm spacing Gullwing Inside “L” PCB through-hole DPDT G6K-2F G6K-2G G6K-2P Model Non-latching 3.2 mm coil-contact terminal spacing G6K-2F-Y G6K-2G-Y G6K-2P-Y Single coil latching 3.2 mm coil-contact terminal spacing G6KU-2F-Y G6KU-2G-Y G6KU-2P-Y When ordering tape packing (surface mount versions), add “-TR” to the model number (e.g., G6K-2G-TR-DC5) Specifications ■ Contact Data Load Rated load Contact material Max. carry current Max. operating voltage Max. operating current Max. switching capacity Min. permissible load (See note) Resistive load (cosφ=1) 0.3 A at 125 VAC 1 A at 30 VDC Ag (Au clad) 1A 125 VAC, 60 VDC 1A 37.5 VA, 30W 10 μA at 10 mVDC Note: This value was measured at a switching frequency of 120 operations/min and the criterion of contact resistance is 50 Ω. This value may vary depending on the switching frequency and operating environment. Always double-check relay suitability under actual operating conditions. Low Signal Relay G6K 67 ■ Coil Data G6K- 2.5 mm coil-contact terminal spacing, standard, non-latching (G6K-2F, G6K-2G, G6K-2P) G6K- 3.2 mm coil-contact terminal spacing, non-latching (G6K-2F-Y, G6K-2G-Y, G6K-2P-Y) Rated voltage (VDC) 3 4.5 5 6 9 12 24 Rated current (mA) 33.0 23.2 21.1 17.6 11.3 9.1 4.6 Coil resistance (Ω) 91 194 237 341 795 1,315 5,220 Pick-up voltage 80% max. Dropout voltage % of rated value 10% min. 150% max. @ 23°C to 70°C Maximum voltage Power consumption (mW) Approx. 100 G6KU- 3.2 mm spacing, single coil latching (G6KU-2F-Y, G6KU-2G-Y, G6KU-2P-Y) Rated voltage (VDC) 3 4.5 5 6 9 12 24 Note: 1. 2. 3. 4. Rated current (mA) 33.0 23.2 21.1 17.6 11.3 9.1 4.6 Coil resistance (Ω) 91 194 237 341 795 1,315 5,220 Set-up voltage 75% max. Reset voltage % of rated value 75% min. 150% max. @ 23°C to 70°C Maximum voltage Power consumption (mW) Approx. 100 The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ± 10%. The operating characteristics are measured at a coil temperature of 23°C unless otherwise specified. Pick-up voltage will vary with temperature The maximum voltage is the highest voltage that can be imposed on the relay coil instantaneously. ■ Characteristics Contact resistance (See note 1) Operate (set) time (See note 2) Release (set) time (See note 2) Insulation resistance (See note 3) Dielectric strength 100 mΩ max. 3 ms max. (Approx. 1.4 ms - standard. Approx. 1.2 ms - latching) 3 ms max. (Approx. 1.3 ms - standard. Approx. 1.2 ms - latching) 1,000 MΩ min. (at 500 VDC) 1,500 VAC for 1 minute between coil contacts 1,000 VAC for 1 minute between contacts of different poles 750 VAC for 1 minute between contacts of the same pole 2,500 V, (2 x 10 μs) between coil and contacts. (Conforms to Bellcore specifications) 1,500 V, (10 x 160 μs) between coil and contacts / contacts of different and same polarity. (Conforms to FCC Part 68) Surge withstand voltage “-Y’ versions Standard versions Vibration Shock Ambient temperature Humidity Service life Weight Note: 1. 2. 3. 4. Mechanical Electrical Mechanical durability 10 to 55 Hz; 5.0 mm double amplitude Malfunction durability 10 to 55 Hz; 3.3 mm double amplitude Mechanical durability 1,000 m/s2 (approx. 100G) Malfunction durability 750 m/s2 (approx. 75G) -40°C to 70°C with no icing or condensation 5 to 85% RH 50,000,000 operations min. (at 36,000 operations per hour) 100,000 operations min. at rated load (at 1,800 operations per hour) Approx. 0.7 g The contact resistance was measured with 10 mA at 1 VDC with a voltage-drop method. Values in parentheses are typical values unless otherwise stated. The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those for checking the dielectric strength. Data shown are of initial value. 68 Low Signal Relay G6K ■ Characteristic data Maximum Switching Capacity Ambient Temperature vs. Maximum Coil Voltage Maximum coil voltage (%) Ambient Temperature vs. Switching Current Rated operating current (A) Rated operating current (A) AC resistive load DC resistive load Rated operating voltage (V) Ambient temperature (°C) Note: The maximum coil voltage refers to the maximum value in a varying range of operating power voltage, not a continuous voltage. Ambient temperature (°C) Electrical Service Life Ambient Temperature vs. Must Ambient Temperature vs. Must Operate or Must Release Voltage Set or Must Reset Voltage G6K-2G (F/P), G6K-2G (F/P)-Y On the basis of rated voltage (%) Max. estimated value G6KU-2G (F/P)-Y On the basis of rated voltage (%) Service Life (x104 operations) Max. estimated value 30 VDC resistive load Ambient temperature: 23°C Switching frequency: 1,800 operations/hour 125 VAC resistive load Ambient temperature: 23°C Switching frequency: 1,800 operations/hour Operate voltage Release voltage Rated operating current (A) Ambient temperature (°C) Ambient temperature (°C) Shock Malfunction Energized Not energized Electrical Service Life (with Must Operate and Must Release Voltage) (See note.) G6K-2G (F/P), G6K-2G (F/P)-Y On the basis of rated voltage (%) Sample: G6K-2G Number of Relays: 10 Test conditions: 1 A resistive load at 30 VDC with an operation rate of 50% Switching frequency: 1,800 operations/h Electrical Service Life (Contact Resistance) (See note.) G6K-2G (F/P), G6K-2G (F/P)-Y Contact resistance (mΩ) Sample: G6K-2G Number of Relays: 10 Test conditions: 1 A resistive load at 30 VDC with an operation rate of 50% Switching frequency: 1,800 operations/h NO contact NC contact Must operate Contact resistance Shock direction Unit: m/s 2 Sample: G6K-2G Number of Relays: 10 Must release Conditions: Shock is applied in ±X, ±Y, and ±Z di rections three times each with and with out energizing the Relays to check the number of contact malfunctions. Operating frequency (x10 3 operations) Note: The tests were conducted at an ambient temperature of 23°C. Operating frequency (x103 operations) Note: The tests were conducted at an ambient temperature of 23°C. Low Signal Relay G6K 69 Contact Reliability Test (See note.) G6K-2G (F/P), G6K-2G (F/P)-Y Mutual Magnetic Interference Mutual Magnetic Interference G6K-2G (F/P), G6K-2G (F/P)-Y Must operate voltage Must release voltage G6K-2G (F/P), G6K-2G (F/P)-Y Must operate voltage Must release voltage Change rate on the basis of initial value (%) Contact resistance (m Ω) Change rate on the basis of initial value (%) Sample: G6K-2G Number of Relays: 10 Test conditions: 10 mA resistive load at 10 mVDC with an operation rate of 50 % Switching frequency: 7,200 operations/h NO contact NC contact Initial stage Test Initial stage Test Sample Not energized Sample Average value Initial stage Test Not energized Average value Initial stage Test Change rate on the basis of initial value (%) Sample Energized Sample Average value Energized Change rate on the basis of initial value (%) Average value Operating frequency (x10 operations) Note 1: The test was conducted at an ambient temperature of 23°C. 2: The contact resistance data are periodically measured reference values and are not values from each monitoring operation. Contact resistance values will vary according to the switching frequency and operating environment, so be sure to check operation under the actual operating conditions before use. 3 External Magnetic Interference Change rate on the basis of initial value (%) Change rate on the basis of initial value (%) Change rate on the basis of initial value (%) G6K-2G (F/P), G6K-2G (F/P)-Y (Average value) (Average value) (Average value) Sample: G6K-2G Number of Relays: 10 Must operate voltage Must release voltage Sample: G6K-2G Number of Relays: 10 Must operate voltage Must release voltage Sample: G6K-2G Number of Relays: 10 Must operate voltage Must release voltage External magnetic field (A/m) External magnetic field (A/m) External magnetic field (A/m) High-frequency Characteristics (Isolation) G6K-2G (F/P), G6K-2G (F/P)-Y Insertion loss (dB) (Average value) High-frequency Characteristics (Insertion Loss) G6K-2G (F/P), G6K-2G (F/P)-Y Return loss (dB) 0 High-frequency Characteristics (Return Loss) G6K-2G (F/P),G6K-2G (F/P)-Y 0 10 20 30 Return loss 40 1.2 1.15 1.1 1.05 V.SWR 80 1 1 10 100 Sample: G6K-2G Number of Relays: 10 1.4 Isolation (dB) 0 10 20 30 40 50 60 70 80 90 Sample: G6K-2G Number of Relays: 10 1.35 1.3 1.25 0.1 0.2 0.3 50 60 0.4 Sample: G6K-2G Number of Relays: 10 10 100 0.5 1 10 100 70 100 1 Frequency (MHz) Frequency (MHz) Frequency (MHz) Note: 1. The tests were conducted at an ambient temperature of 23°C. 2. High-frequency characteristics depend on the PCB to which the Relay is mounted. Always check these characteristics including endurance in the actual machine before use. 70 Low Signal Relay G6K V.SWR (Average value) (Average value) Must Operate and Must Release Time Distribution (See note.) G6K-2G (F/P), G6K-2G (F/P)-Y Number of contacts Sample: G6K-2G Number of Relays: 50 Must operate Must release time Must Operate and Must Release Bounce Time Distribution (See note.) G6K-2G (F/P) , G6K-2G (F/P)-Y Number of contacts Must operate bounce time Must release bounce time Vibration Resistance G6K-2G (F/P), G6K-2G (F/P)-Y Change rate on the basis of rated value (%) Must operate voltage Must release voltage Sample: G6K-2G Number of Relays: 50 ■ Approvals DPDT Time (ms) Note: The tests were conducted at an ambient temperature of 23°C. Time (ms) After test UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C Contact form Coil rating 3 to 24 VDC Contact ratings 1 A at 30 VDC (Resistive) 0.5 A at 60 VDC (Resistive) 0.3 A at 125 VAC (General Use) Number of test operations 6,000 Dimensions Note: All units are in millimeters unless otherwise indicated. G6K-2F Mounting Dimensions (Top View) Tolerance: ±0.1 mm Terminal Arrangement/ Internal Connections (Top View) Note: Each value has a tolerance of ±0.3 mm. Orientation mark G6K-2G Mounting Dimensions (Top View) Tolerance: ±0.1 mm Terminal Arrangement/ Internal Connections (Top View) Note: Each value has a tolerance of ±0.3 mm. Orientation mark G6K-2P Mounting Dimensions (Bottom View) Terminal Arrangement/ Tolerance: ±0.1 mm Internal Connections (Bottom View) Eight, 0.8-dia. holes Orientation mark Note: Each value has a tolerance of ±0.3 mm. Low Signal Relay G6K 71 G6K-2F-Y Mounting Dimensions (Top View) Tolerance: ±0.1 mm Terminal Arrangement/ Internal Connections (Top View) Note: Each value has a tolerance of ±0.3 mm. Orientation mark G6K-2G-Y Mounting Dimensions (Top View) Tolerance: ±0.1 mm Terminal Arrangement/ Internal Connections (Top View) Note: Each value has a tolerance of ±0.3 mm. Orientation mark G6K-2P-Y Mounting Dimensions (Bottom View) Tolerance: ±0.1 mm Eight, 0.8-dia. holes Terminal Arrangement/ Internal Connections (Bottom View) Orientation mark Note: Each value has a tolerance of ±0.3 mm. G6KU-2F-Y Mounting Dimensions (Top View) Tolerance: ±0.1 mm Terminal Arrangement/ Internal Connections (Top View) Note: Each value has a tolerance of ±0.3 mm. Orientation mark G6KU-2G-Y Mounting Dimensions (Top View) Tolerance: ±0.1 mm Terminal Arrangement/ Internal Connections (Top View) Note: Each value has a tolerance of ±0.3 mm. Orientation mark G6KU-2P-Y Mounting Dimensions (Bottom View) Terminal Arrangement/ Internal Connections Tolerance: ±0.1 mm Eight, 0.8-dia. holes (Bottom View) Orientation mark Note: Each value has a tolerance of ±0.3 mm. 72 Low Signal Relay G6K ■ Packaging Information Tube packing Standard nomenclature 50 pcs per anti-static tube 900 pcs per reel 2 reels per box Order in box multiples (see details below) Tape packing When ordering, add “TR” before the rated coil voltage (e.g., G6K-2G-TR-DC5). (SMT versions, only) Note: TR is not part of the relay model number and will not be marked on the relay. Relays in tube packing are arranged so that the orientation mark of each Relay is on the left side. Be sure to reference Relay orientation when mounting the Relay to the PCB. Stopper (gray) Orientation of Relays Stopper (green) Tube length: 520 mm (stopper not included) No. of Relays per Tube: 50 ■ Tape and Reel Dimensions (Surface Mount Models) • Tape type: ETX7200 (EIAJ - Electronic Industrial Association of Japan) • Reel type: RPM-16D (EIAJ, 330 mm diameter) • Relays per reel: 900 1. Direction of Relay Insertion Top tape (cover tape) Orientation mark 3. Carrier Tape Dimensions G6K-2F, G6K-2F-Y, G6KU-2F-Y Pulling direction Carrier tape Emboss tape 2. Reel Dimensions G6K-2G, G6K-2G-Y, G6KU-2G-Y Low Signal Relay G6K 73 ■ Recommended Soldering Method Temperature indicates the surface temperature of the PCBs. IRS Method (for surface mounting terminal models) (1) IRS Method (Mounting Solder: Lead) Temperature (°C) (2) IRS Method (Mounting Solder: Lead-free) Temperature (°C) Upper surface of case (peak): 255˚C max. Soldering 220 to 245 180 to 200 Soldering 250 max. 230 180 150 Preheating Relay terminal section 120 max. 30 max. 150 Preheating Time (s) Note: The temperature profile indicates the Time (s) temperature of the relay terminal section. • The thickness of cream solder to be applied should be within a range between 150 and 200 μm on OMRON’s recommended PCB pattern. • In order to perform correct soldering, it is recommended that the correct soldering conditions be maintained as shown below on the left side. 90 to 120 20 to 30 Correct Soldering Relay Terminal Solder Land Incorrect Soldering Insufficient amount of solder Excessive amount of solder PCB Visually check that the Relay is properly soldered. Precautions ■ Correct Use Handling Do not unpack the relay until mounting it. Environmental Conditions During Operation, Storage, and Transportation It is best to keep the relay in its packaging in a controlled environment until it is ready for mounting. If the Relay is stored for a long time in an adverse environment with high temperature, high humidity, organic gases, or sulfide gases, sulfide or oxide films will form on the contact surfaces. These films may result in unstable contact, contact problems, or functional problems. Therefore, operate, store, or transport the product under specified environmental conditions. Soldering Solder: JIS Z3282, H63A or equivalent Soldering temperature: Approx. 250°C (260°C if the DWS method is used) Soldering time: Approx. 5 s max. (approx. 2 s for the first time and approx. 3 s for the second time if the DWS method is used) Be sure to make a molten solder level adjustment so that the solder will not overflow on the PCB. Latching Relay Mounting Make sure that the vibration or shock that is generated from other devices, such as relays in operation, on the same panel and imposed on the Latching Relay does not exceed the rated value, otherwise the Latching Relay that has been set may be reset or vice versa. The Latching Relay is reset before shipping. If excessive vibration or shock is imposed, however, the Latching Relay may be set accidentally. Be sure to apply a reset signal before use. Claw Securing Force During Automatic Mounting During automatic insertion of Relays, make sure to set the securing force of each claw to the following so that the Relays characteristics will be maintained. Maximum Allowable Voltage The maximum allowable voltage of the coil can be obtained from the coil temperature increase and the heat-resisting temperature of coil insulating sheath material. (Exceeding the heat-resisting temperature may result in burning or short-circuiting.) The maximum allowable voltage also involves important restrictions which include the following: Direction A: 1.96 N Direction B: 4.90 N Direction C: 1.96 N 74 Low Signal Relay G6K • Must not cause thermal changes in or deterioration of the insulating material. • Must not cause damage to other control devices. • Must not cause any harmful effect on people. • Must not cause fire. Therefore, be sure to use the maximum allowable voltage as specified in the catalog. As a rule, the rated voltage must be applied to the coil. A voltage exceeding the rated value, however, can be applied to the coil provided that the voltage is less than or equal to the maximum allowable voltage. It must be noted that continuous voltage application to the coil will cause a coil temperature increase which may affect characteristics such as electrical life and coil insulation. Coating The Relay mounting on the PCB may be coated or washed but do not apply silicone coating or detergent containing silicone, otherwise the silicone coating or detergent may remain on the surface of the Relay. PCB Mounting If two or more Relays are closely mounted with the long sides of the Relays facing each other and soldering is performed with infrared radiation, the solder may not be properly exposed to the infrared rays. Be sure to keep the proper distance between adjacent Relays as shown below to insure formation of good solder joints. G6K-2G 2 mm min. G6K-2F 2.7 mm min. Two or more Relays may be mounted as closely as desired with the short sides of the Relays facing each other. Low Signal Relay G6K 75 MEMO 76 Low Signal Relay G6K Omron Electronic Components, LLC Terms and Conditions of Sales I. GENERAL 1. Definitions: The words used herein are defined as follows. (a) Terms: These terms and conditions (b) Seller: Omron Electronic Components LLC and its subsidiaries (c) Buyer: The buyer of Products, including any end user in section III through VI (d) Products: Products and/or services of Seller (e) Including: Including without limitation 2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments, invoices, purchase orders and other documents, whether electronic or in writing, relating to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's purchase order or other documents which are inconsistent with, or in addition to, these Terms. 3. Distributor: Any distributor shall inform its customer of the contents after and including section III of these Terms. II. SALES 1. Prices; Payment: All prices stated are current, subject to change without notice by Seller. Buyer agrees to pay the price in effect at the time the purchase order is accepted by Seller. Payments for Products received are due net 30 days unless otherwise stated in the invoice. Buyer shall have no right to set off any amounts against the amount owing in respect of this invoice. 2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to Buyer after deducting transportation charges, taxes and duties, and will be allowed only if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past due amounts owing to Seller. 3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum legal rate, whichever is less, on any balance not paid within the stated terms. 4. Orders: Seller will accept no order less than 200 U.S. dollars net billing. 5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer shall make remittance to Seller at the then current exchange rate most favorable to Seller; provided that if remittance is not made when due, Buyer will convert the amount to U.S. dollars at the then current exchange rate most favorable to Seller available during the period between the due date and the date remittance is actually made. 6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining any government approvals regarding the importation or sale of the Products. 7. Taxes: All taxes, duties and other governmental charges (other than general real property and income taxes), including any interest or penalties thereon, imposed directly or indirectly on Seller or required to be collected directly or indirectly by Seller for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by Buyer to Seller. 8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller, Seller reserves the right to stop shipments or require satisfactory security or payment in advance. If Buyer fails to make payment or otherwise comply with these Terms or any related agreement, Seller may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid accounts. 9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer indemnifies Seller fully against all costs or expenses arising in connection therewith. 10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller: (a) All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Seller), at which point title to and all risk of loss of the Products shall pass from Seller to Buyer, provided that Seller shall retain a security interest in the Products until the full purchase price is paid by Buyer; (b) Delivery and shipping dates are estimates only; and (c) Seller will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions. 12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products occurring before delivery to the carrier or any claim related to pricing or other charges must be presented in detail in writing to Seller within 30 days of receipt of shipment. III. PRECAUTIONS 1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E) SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT. Buyer acknowledges that it alone has determined that the Products will meet their requirements of the intended use in all cases. Buyer must know and observe all prohibitions of use applicable to the Product/s. 2. Use with Attention: The followings are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible use of any Product, nor to imply that any use listed may be suitable for any Product: (a) Outdoor use, use involving potential chemical contamination or electrical interference. (b) Use in consumer Products or any use in significant quantities. (c) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (d) Systems, machines, and equipment that could present a risk to life or property. 3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY SELLER. 5. Programmable Products: Seller shall not be responsible for the Buyer's programming of a programmable Product. IV. WARRANTY AND LIMITATION 1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Seller (or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES, NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. 2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an amount equal to the purchase price of the Product; provided that there shall be no liability for Seller or its affiliates unless Seller's analysis confirms that the Products were correctly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Seller before shipment. 3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF THE PRODUCT ON WHICH LIABILITY IS ASSERTED. 4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its employees from and against all liabilities, losses, claims, costs and expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or omissions under these Terms or in any way with respect to the Products. V. INFORMATION; ETC. 1. Intellectual Property: The intellectual property embodied in the Products is the exclusive property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way without the written permission of Seller. Buyer (at its own expense) shall indemnify and hold harmless Seller and defend or settle any action brought against Seller to the extent that it is based on a claim that any Product made to Buyer specifications infringed intellectual property rights of another party. 2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or tooling, all engineering and tooling shall remain the exclusive property of Seller. All information and materials supplied by Seller to Buyer relating to the Products are confidential and proprietary, and Buyer shall limit distribution thereof to its trusted employees and strictly prevent disclosure to any third party. 3. Performance Data: Performance data is provided as a guide in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must correlate it to actual application requirements. 4. Change In Specifications: Product specifications and descriptions may be changed at any time based on improvements or other reasons. It is Seller’s practice to change part numbers when published ratings or features are changed, or when significant engineering changes are made. However, some specifications of the Product may be changed without any notice. 5. Errors And Omissions: The information on Seller’s website or in other documentation has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses regarding (a) export of the Products or information provided by Seller; (b) sale of Products to forbidden or other proscribed persons or organizations; (c) disclosure to noncitizens of regulated technology or information. VI. MISCELLANEOUS 1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing between Buyer and Seller shall operate as a waiver of rights by Seller. 2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent. 3. Law: These Terms are governed by Illinois law (without regard to conflict of laws). Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any dispute hereunder. 4. Amendment: These Terms constitute the entire agreement between Buyer and Seller relating to the Products, and no provision may be changed or waived unless in writing signed by the parties. 5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. Low Signal Relay G6K Certain Precautions on Specifications and Use 1. Suitability for Use. Seller shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in Buyer's application or use of the Product. At Buyer's request, Seller will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer shall take application responsibility in all cases but the following is a nonexhaustive list of applications for which particular attention must be given: (i) Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. (ii) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (iii) Use in consumer products or any use in significant quantities. (iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this product. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 2. Programmable Products. Seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof. 3. Performance Data. Performance data given in this publication is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to Seller's Warranty and Limitations of Liability. 4. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Seller representative at any time to confirm actual specifications of purchased Product. 5. Errors and Omissions. The information in this publication has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors, or omissions. 6. RoHS Compliance. Where indicated, our products currently comply, to the best of our knowledge as of the date of this publication, with the requirements of the European Union's Directive on the Restriction of certain Hazardous Substances ("RoHS"), although the requirements of RoHS do not take effect until July 2006. These requirements may be subject to change. Please consult our website for current information. Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ELECTRONIC COMPONENTS LLC 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 OMRON ON-LINE Global - http://www.omron.com USA - http://www.components.omron.com 847-882-2288 Cat. No. X301-E-1 06/09 Specifications subject to change without notice Printed in USA Low Signal Relay G6K