G6WU-1F

High-frequency Relay G6W Surface-mountable 5 GHz Band Miniature SPDT High-frequency Relay • Superior high-frequency characteristics, such as an isolation of 35 dB min., insertion loss of 0.5 dB max., and V.S.W.R. of 1.7 max. at 5 GHz (50 Ω). • High-frequency characteristics obtained by adopting tri-plate micro strip line design. • Small size at 20 x 9.4 x 8.9 mm (L x W x H). • Y-shape terminal structure and reverse contact option simplifies wiring to PCBs. • RoHS Compliant. Ordering Information Classification SPDT Fully sealed Through-hole terminal Surface-mount terminal Y-shape terminal Y-shape terminal Non latching G6W-1P G6W-1F Single-coil latching G6WU-1P G6WU-1F Dual-coil latching G6WK-1P G6WK-1F Note: When ordering, add the rated coil voltage to the model number. Example: G6W-1P DC12 Rated coil voltage Model Number Legend: G6W 1 234 5 3. Terminal shape F: P: Surface-mount terminals PCB through-hole terminals 5. Contact Arrangement None: Standard contact arrangement R: Reverse contact arrangement (Available only for Non-Latching versions) 1. Relay function None: Non-latching U: K: 1: Single-coil latching Dual-coil latching SPDT 4. Terminal Structure None: Y-shape terminal (standard) 2. Contact form ■ Typical Applications • • • • Mobile phone base station (W-CDMA, UMTS, CDMA-2000, PCS) Wireless LAN and TV transmitters Test and Measurement devices Signal Generators High-frequency Relay G6W 327 Specifications ■ Contact Ratings Load type Contact material Rated load Rated carry current Max. switching voltage Max. switching current Resistive load Au clad Cu alloy 10 mA at 30 VAC; 10 mA at 30 VDC 2.5 GHz, 50 Ω, 10 W (See note 2) 0.5 A 30 VDC, 30 VAC 0.5 A ■ High-frequency Characteristics Frequency Isolation Insertion loss V.S.W.R. Max. carry power Max. switching power 2.0 GHz 65 dB min. 0.2 dB max. 1.2 max. 20 W (See note 2) 10 W (See note 2) 2.5 GHz 60 dB min. 35 dB min. 0.5 dB max. 1.7 max. 5.0 GHz Note: 1. The above values are initial values. 2. These values are for a load with V.S.W.R. ≤1.2 at an impedance of 50 Ω. ■ Coil Ratings Non-latching Relays (G6W-1F, G6W-1P) Rated voltage Rated current Coil resistance Must operate voltage Must release voltage Maximum voltage Power consumption 3 VDC 66.7 mA 45 Ω 4.5 VDC 44.4 mA 101 Ω 9 VDC 22.2 mA 405 Ω 12 VDC 16.7 mA 720 Ω 24 VDC 8.3 mA 2,880 Ω 80% of max. of rated voltage 10% min. of rated voltage 150% of rated voltage Approx. 200 mW Single-coil Latching Relays (G6WU-1F, G6WU-1P) Rated voltage Rated current Coil resistance Must set voltage Must reset voltage Maximum voltage Power consumption 9 VDC 22.2 mA 405 Ω 80% max. of rated voltage 80% max of rated voltage 150% of rated voltage Approx. 200 mW 12 VDC 16.7 mA 720 Ω Dual-coil Latching Relays (G6WK-1F, G6WK-1P) Rated voltage Rated current Coil resistance Must set voltage Must reset voltage Maximum voltage Power consumption Note: 1. 2. 3. 4. 3 VDC 120 mA 25 Ω 4.5 VDC 80 mA 56 Ω 9 VDC 40 mA 225 Ω 12 VDC 30 mA 400 Ω 24 VDC 15 mA 1,600 Ω 80% max. of rated voltage 80% max. of rated voltage 150% of rated voltage Approx. 360 mW The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ± 10%. The operating characteristics are measured at a coil temperature of 23°C. The maximum voltage is the highest voltage that can be imposed on the relay coil. The voltage measurements for operate/release and set/reset are the values obtained for instantaneous changes in the voltage. (Rectangular wave). 328 High-frequency Relay G6W ■ Characteristics Item Contact resistance (See note 2) Operate (set) time (See note 3) Release (reset) time (See note 3) Minimum set/reset signal width Insulation resistance (See note 4) Dielectric strength Coil and contacts Coil and ground, contacts and ground Contact of same polarity Vibration resistance Shock resistance Endurance Destruction Malfunction Destruction Malfunction Mechanical Electrical Ambient temperature Ambient humidity Weight Note: 1. 2. 3. 4. Non-latching G6W-1F, G6W-1P 100 mΩ max. 10 ms max. (Approx. 3.5 ms) 10 ms max. (Approx. 2.5 ms) 10 ms max. (Approx. 2.5 ms) ----1,000 MΩ min. (at 500 VDC) 1,000 VAC, 50/60 Hz for 1 min 500 VAC, 50/60 Hz for 1 min 500 VAC, 50/60 Hz for 1 min 10 to 55 Hz, 1.5-mm double amplitude 10 to 55 Hz, 2-mm double amplitude 1,000 m/s2 500 m/s2 1,000,000 operations min. (at 36,000 operations/hour) 300,000 operations min. (with a rated load at 1,800 operations/hour) 100,000 operations min. (2.5GHz, 50 Ω, 10 W) Operating: -40°C to 70°C (with no icing or condensation) Operating: 5% to 85% Approx. 3 g The above values are initial values. The contact resistance was measured with 10 mA at 1 VDC with a fall-of-potential method. Values in parentheses are typical values. The insulation resistance was measured with a 500-VDC Megger Tester applied to the same parts as those used for checking the dielectric strength. 12 ms Single-coil latching G6WU-1F, G6WU-1P Dual-coil latching G6WK-1F, G6WK-1P Engineering Data Ambient Temperature vs. Maximum Voltage Maximum voltage (%) On the basis of rated voltage (%) 250 Ambient Temperature vs. Must Set or Must Reset Voltage 100 90 80 70 60 50 Max. estimated value max. avg. max. avg. min. min. Shock Malfunction Y 1,000 800 X 1,000 600 Not 400 energized 200 Z 1,000 Energized 200 150 100 200 40 30 20 10 Must set voltage Must reset voltage −40 −20 0 20 40 60 80 100 Y' 1,000 Z' Shock direction X X' Y Z Z' 400 600 800 1,000 Unit: m/s2 Sample: G6WK-1P 4.5 VDC Number of Relays: 10 1,000 X' 50 0 −40 Y' −20 0 20 40 60 80 100 0 −60 Ambient temperature (°C) Ambient temperature (°C) Note: “Maximum voltage” is the maximum voltage that can be applied to the relay coil. Conditions: Shock is applied in ±X, ±Y, and ±Z directions three times each with and without energizing the relays to check the number of contact malfunctions. High-frequency Relay G6W 329 Electrical Endurance, DC Load: Must Set and Must Reset Voltage (See notes 1 and 2) On the basis of rated voltage (%) 100 Electrical Endurance, AC Load: Must Set and Must ResetVoltage (See notes 1 and 2) On the basis of rated voltage (%) 100 80 Must set voltage max. max. 80 Must set voltage 60 max. max. min. min. Must reset voltage 40 60 min. Must reset voltage min. 40 Sample: G6WU-1P 9 VDC 20 Number of Relays: 5 Test conditions: 10-mA resistive load at 30-VDC with an operation rate of 50%. Switching frequency: 1,800 operations/h 0 0.001 0.01 0.1 1 10 100 1,000 Sample: G6WU-1P 9 VDC 20 Number of Relays: 5 Test conditions: 10-mA resistive load at 30-VAC with an operation rate of 50%. Switching frequency: 1,800 operations/h 0 0.001 0.01 0.1 1 10 100 1,000 Operating frequency (×103 operations) Operating frequency (×103 operations) Electrical Endurance, DC Load: Contact Resistance (See notes 1 and 2) Contact resistance (m ) 1,000 Sample: G6WU-1P 9 VDC NO contact Number of Relays: 5 NC contact 500 Test conditions: 10-mA resistive load at 30-VDC Switching frequency: 1,800 operations/h 300 Electrical Endurance, AC Load: Contact Resistance (See notes 1 and 2) Contact resistance (m ) 1,000 Sample: G6WU-1P 9 VDC NO contact Number of Relays: 5 NC contact 500 Test conditions: 10-mA resistive load at 30-VAC Switching frequency: 1,800 operations/h 300 100 100 50 Contact resistance 30 max. max. min. min. 50 Contact resistance 30 max. max. min. min. 10 0.001 0.01 0.1 1 10 100 1,000 10 0.001 0.01 0.1 1 10 100 1,000 Operating frequency (×103 operations) Operating frequency (×103 operations) External Magnetic Interference (Average value) Change rate on the basis of initial value (%) Change rate on the basis of initial value (%) Sample: G6WK-1P 4.5 VDC Number of Relays: 5 S N Sample: G6WK-1P 4.5 VDC Number of Relays: 5 Change rate on the basis of initial value (%) +30 (Average value) +30 +30 S N Sample: G6WK-1P 4.5 VDC Number of Relays: 5 S (Average value) N +20 +20 +20 +10 +10 +10 0 0 0 −10 −10 −10 −20 −30 −1,200 Must set voltage Must reset voltage −800 −400 0 400 800 1,200 −20 −30 −1,200 Must set voltage Must reset voltage −800 −400 0 400 800 1,200 −20 −30 −1,200 Must set voltage Must reset voltage −800 −400 0 400 800 1,200 External magnetic field (A/m) External magnetic field (A/m) External magnetic field (A/m) Note: 1. The tests were conducted at an ambient temperature of 23°C 2. The contact resistance data are periodically measured reference values and are not values from monitoring each operation. Contact resistance values will vary according to the switching frequency and operating environment. Therefore, be sure to check the operation under the actual operating conditions before use. 330 High-frequency Relay G6W Isolation (See notes 1 and 2) [Average (Initial value)] Insertion Loss (See notes 1 and 2) [Average (Initial value)] V.S.W.R. / Return Loss (See notes 1 and 2) [Average (Initial value)] Isolation (dB) Return loss (dB) N.O. N.C. 20 10 2.2 0.2 Return loss 20 2.0 40 0.4 30 1.8 60 0.6 80 50 100 N.O. N.C. 0 1,000 2,000 3,000 4,000 5,000 6,000 0.8 60 1.0 N.O. N.C. 0 1,000 2,000 3,000 4,000 5,000 6,000 70 0 1,000 2,000 3,000 4,000 1.0 5,000 6,000 1.2 40 1.6 V.S.W.R. 1.4 120 Frequency (MHz) Frequency (MHz) Frequency (MHz) Must Set and Must Reset Time Distribution (see note 1). Number of contacts 20 Sample: G6WK-1P 4.5 VDC Number of Relays: 20 Must set time Must reset time Must Set and Must Reset Bounce Time Distribution (see note 1). Number of contacts 30 Sample: G6WK-1P 4.5 VDC Number of Relays: 20 Must set bounce time Must reset bounce time 25 15 20 10 15 10 5 5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 0 0.5 1.0 1.5 2.0 2.5 3.0 Time (ms) Time (ms) Note: 1. The tests were conducted at an ambient temperature of 23°C. 2. High-frequency characteristics depend upon the PCB to which the relay is mounted. Always check these characteristics, including endurance (life expectancy) in the actual application before use. Dimensions Note: All units are in millimeters unless otherwise indicated. G6W-1F G6WU-1F Mounting Pads (Top View) Tolerance: ±0.1 mm 2.54 2.54 2.54 2.54 5.08 3.2 18 2.7 1.8 5.08 9.4 20 20 9.4 1.1 3 8.6 20.4 5.9 2.8 1.1 Terminal Arrangement/ Internal Connections (Top View) G6W-1F Orientation mark 17 + 15 14 13 − 11 10 1 2 3 5 67 8 Through-hole 9.2 G6WU-1F Orientation mark 18 17 S+ R− 20 15 14 13 − + 8 11 10 Twelve, 0.6 15.24 22.2 Three, 0.4 0.2 0.2 5.08 11.6 1 Note: 1. Tolerance: ±0.3 mm unless specified. 2. The coplanarity of the terminals is 0.1 mm max. 2 3 5 67 High-frequency Relay G6W 331 V.S.W.R. 0 Insertion loss (dB) 0 0 2.4 G6W-1P G6WU-1P 1.6-dia. 0.8-dia. Mounting Holes (Bottom View) Tolerance: ±0.1 mm 2.54 2.54 2.54 2.54 2.54 2.54 0.8-dia. 1.6-dia. 20 2.7 1.8 5.08 7.62 18 3 0.8-dia. 8.6 19 1.6-dia. 5.9 Terminal Arrangement/ Internal Connections (Bottom View) G6W-1P Orientation mark 1 2 3 5 67 8 + 17 − 15 14 13 11 10 20 9.4 Twelve, 1-dia. Twelve, 1.8-dia. Through-hole G6WU-1P Orientation mark 20 1 2 S+ R− 18 17 3 − + 15 14 13 11 10 5 67 8 8.9 Twelve, 0.6 5.08 10.16 15.24 19 Three, 0.4 5.08 7.6 Note: Tolerance: ±0.3 mm unless specified. G6WK-1F Mounting Pads (Top View) Tolerance: ±0.1 mm 2.54 2.54 2.54 2.54 5.08 3.2 18 20 9.4 2.7 1.8 5.08 9.4 20 Terminal Arrangement/ Internal Connections (Top View) G6WK-1F Orientation mark 17 16 + 15 14 − S 3 5 13 + − R 11 10 9.2 Throughhole 1.1 3 8.6 20.4 5.9 2.8 1.1 1 2 67 8 Thirteen, 0.6 15.24 22.2 Three, 0.4 0.2 0.2 5.08 11.6 Note: 1. Tolerance: ±0.3 mm unless specified. 2. The coplanarity of the terminals is 0.1 mm max. G6WK-1P Mounting Holes (Bottom View) Tolerance: ±0.1 mm 1.6-dia. 0.8-dia. 2.54 2.54 2.54 2.54 2.54 2.54 0.8-dia. 1.6-dia. 20 2.7 1.8 5.08 7.62 18 3 0.8-dia. 8.6 19 5.9 1.6-dia. Terminal Arrangement/ Internal Connections (Bottom View) G6WK-1P Orientation mark 1 2 + 3 − S 15 14 5 67 8 20 9.4 + 13 − R 11 Thirteen, 1-dia. 8.9 Thirteen, 1.8-dia. Through-hole 17 16 10 Thirteen, 0.6 5.08 10.16 15.24 19 Three, 0.4 5.08 7.6 Note: Tolerance: ±0.3 mm unless specified. 332 High-frequency Relay G6W Recommended Soldering Method ■ Temperature Profile According to IRS Method When performing reflow-soldering, check the profile on an actual device after setting the temperature condition so that the temperatures at the relay terminals and the upper surface of the case do not exceed the limits specified in the following table. Temperature (°C) The thickness of cream solder to be applied should be within a range between 150 and 200 μm on OMRON's recommended PCB pattern. Correct Soldering Relay T4 T3 PCB Terminal Solder Land Incorrect Soldering Insufficient amount of solder Excessive amount of solder T2 T1 Visually check that the Relay is properly soldered. Bottom Ground Soldering Conditions To solder the bottom ground, manually solder separately from the terminals according to the following conditions. • Soldering iron: 50 W • Iron temperature: 380°C to 400°C • Soldering time: 10 s max. t1 Preheating t2 Soldering Time (s) Item Measuring position Terminal Preheating (T1 to T2, t1) Soldering (T3, t2) Peak value (T4) 250°C max. 255°C max. Note: The above conditions are for a PCB with OMRON’s recommended patterns and hole perforations. The conditions will depend on the PCB being used. Therefore, it is recommended to double-check the suitability under actual PCB conditions. Soldering Soldering temperature: Approx. 250°C (At 260°C if the DWS method is used.) Soldering time: Approx. 5 s max. (approx. 2 s for the first time and approx. 3 s for the second time if the DWS method is used.) Be sure to adjust the level of the molten solder so that the solder will not overflow onto the PCB. 150°C to 180°C, 230°C min., 120 s max. 30 s max. --- Upper surface --of case Precautions ■ Correct Use Handling Use the Relay as soon as possible after opening the moisture-proof package. If the Relay is left for a long time after opening the moistureproof package, the appearance may suffer and seal failure may occur after the solder mounting process. To store the Relay after opening the moisture-proof package, place it into the original package and sealed the package with adhesive tape. When washing the product after soldering the Relay to a PCB, use a water-based solvent or alcohol-based solvent, and keep the solvent temperature to less than 40°C. Do not put the Relay in a cold cleaning bath immediately after soldering. Dropping the Relay may cause damage to its functional capability. Never use the Relay if it is dropped. Protect the Relays from direct sunlight during operation, storage, and transportation and keep the relays under normal temperature, humidity, and pressure. Claw Securing Force During Automatic Insertion During automatic insertion of Relays, make sure to set the securing force of the claws to the following values so that the Relay characteristics will be maintained. C A B Direction A: 4.90 N max. Direction B: 9.80 N max. Direction C: 9.80 N max. Secure the claws to the area indicated by shading. Do not attach them to the center area or to only part of the Relay. Latching Relay Mounting Make sure that the vibration or shock that is generated from other devices, such as relays in operation, on the same panel and imposed on the Latching Relay does not exceed the rated value, otherwise the Latching Relay that has been set may be reset or vice versa. The Latching Relay is reset before shipping. If excessive vibration or shock is imposed, however, the Latching Relay may be set accidentally. Be sure to apply a reset signal before use. Coating Do not use silicone coating to coat the Relay when it is mounted to the PCB. Do not wash the PCB after the Relay is mounted using detergent containing silicone. Otherwise, the detergent may remain on the surface of the Relay. High-frequency Relay G6W 333 ■ High-frequency Characteristics Measurement Method and Substrate to be Measured High-frequency Characteristics for G6W are measured as shown below. G6W-1 Vector network analyzer (Manufacture: Agilent Technologies) HP8753D 50- termination resistances Through-hole substrate Substrate: t-0.8 BT resin (Dielectric constant at 2 GHz: 3.37) 1.5 0.5 0.5 0.4 1.8-dia. SMD-type substrate Substrate: t-0.8 BT resin (Dielectric constant at 2 GHz: 3.37) 0.5 1.5 1.4 0.4 Through-hole 4.5 Throughhole 1.8 R0.6 20 6 1.8 5.12 1.5 0.5 Twenty seven, 0.6-dia., through-hole 45° 45° R2.1 1.5 1.5 0.5 0.5 3 8.6 30 3 Thirty one, 0.6-dia., through-hole 3 8.6 15.24 3 Undersurface of relay Undersurface of relay Convex position Convex position Note: To obtain high-frequency characteristics close to those specified in this datasheet, solder the convex point on the undersurface of the relay to the ground pattern of the substrate. Base plate for high-frequency characteristic compensation 13.6 2 Twenty four, 0.6-dia., through-hole 0.5 1.5 15 Note: The above compensation plate is used to measure the loss by the relay. The relay loss is determined by subtracting the data measured for a compensation base plate from those for a high-frequency characteristics measuring substrate mounted with a relay. 334 High-frequency Relay G6W Omron Electronic Components, LLC Terms and Conditions of Sales I. GENERAL 1. Definitions: The words used herein are defined as follows. (a) Terms: These terms and conditions (b) Seller: Omron Electronic Components LLC and its subsidiaries (c) Buyer: The buyer of Products, including any end user in section III through VI (d) Products: Products and/or services of Seller (e) Including: Including without limitation 2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments, invoices, purchase orders and other documents, whether electronic or in writing, relating to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's purchase order or other documents which are inconsistent with, or in addition to, these Terms. 3. Distributor: Any distributor shall inform its customer of the contents after and including section III of these Terms. II. SALES 1. Prices; Payment: All prices stated are current, subject to change without notice by Seller. Buyer agrees to pay the price in effect at the time the purchase order is accepted by Seller. Payments for Products received are due net 30 days unless otherwise stated in the invoice. Buyer shall have no right to set off any amounts against the amount owing in respect of this invoice. 2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to Buyer after deducting transportation charges, taxes and duties, and will be allowed only if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past due amounts owing to Seller. 3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum legal rate, whichever is less, on any balance not paid within the stated terms. 4. Orders: Seller will accept no order less than 200 U.S. dollars net billing. 5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer shall make remittance to Seller at the then current exchange rate most favorable to Seller; provided that if remittance is not made when due, Buyer will convert the amount to U.S. dollars at the then current exchange rate most favorable to Seller available during the period between the due date and the date remittance is actually made. 6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining any government approvals regarding the importation or sale of the Products. 7. Taxes: All taxes, duties and other governmental charges (other than general real property and income taxes), including any interest or penalties thereon, imposed directly or indirectly on Seller or required to be collected directly or indirectly by Seller for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by Buyer to Seller. 8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller, Seller reserves the right to stop shipments or require satisfactory security or payment in advance. If Buyer fails to make payment or otherwise comply with these Terms or any related agreement, Seller may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid accounts. 9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer indemnifies Seller fully against all costs or expenses arising in connection therewith. 10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller: (a) All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Seller), at which point title to and all risk of loss of the Products shall pass from Seller to Buyer, provided that Seller shall retain a security interest in the Products until the full purchase price is paid by Buyer; (b) Delivery and shipping dates are estimates only; and (c) Seller will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions. 12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products occurring before delivery to the carrier or any claim related to pricing or other charges must be presented in detail in writing to Seller within 30 days of receipt of shipment. III. PRECAUTIONS 1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E) SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT. Buyer acknowledges that it alone has determined that the Products will meet their requirements of the intended use in all cases. Buyer must know and observe all prohibitions of use applicable to the Product/s. 2. Use with Attention: The followings are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible use of any Product, nor to imply that any use listed may be suitable for any Product: (a) Outdoor use, use involving potential chemical contamination or electrical interference. (b) Use in consumer Products or any use in significant quantities. (c) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (d) Systems, machines, and equipment that could present a risk to life or property. 3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY SELLER. 5. Programmable Products: Seller shall not be responsible for the Buyer's programming of a programmable Product. IV. WARRANTY AND LIMITATION 1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Seller (or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES, NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. 2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an amount equal to the purchase price of the Product; provided that there shall be no liability for Seller or its affiliates unless Seller's analysis confirms that the Products were correctly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Seller before shipment. 3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF THE PRODUCT ON WHICH LIABILITY IS ASSERTED. 4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its employees from and against all liabilities, losses, claims, costs and expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or omissions under these Terms or in any way with respect to the Products. V. INFORMATION; ETC. 1. Intellectual Property: The intellectual property embodied in the Products is the exclusive property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way without the written permission of Seller. Buyer (at its own expense) shall indemnify and hold harmless Seller and defend or settle any action brought against Seller to the extent that it is based on a claim that any Product made to Buyer specifications infringed intellectual property rights of another party. 2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or tooling, all engineering and tooling shall remain the exclusive property of Seller. All information and materials supplied by Seller to Buyer relating to the Products are confidential and proprietary, and Buyer shall limit distribution thereof to its trusted employees and strictly prevent disclosure to any third party. 3. Performance Data: Performance data is provided as a guide in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must correlate it to actual application requirements. 4. Change In Specifications: Product specifications and descriptions may be changed at any time based on improvements or other reasons. It is Seller’s practice to change part numbers when published ratings or features are changed, or when significant engineering changes are made. However, some specifications of the Product may be changed without any notice. 5. Errors And Omissions: The information on Seller’s website or in other documentation has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses regarding (a) export of the Products or information provided by Seller; (b) sale of Products to forbidden or other proscribed persons or organizations; (c) disclosure to noncitizens of regulated technology or information. VI. MISCELLANEOUS 1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing between Buyer and Seller shall operate as a waiver of rights by Seller. 2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent. 3. Law: These Terms are governed by Illinois law (without regard to conflict of laws). Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any dispute hereunder. 4. Amendment: These Terms constitute the entire agreement between Buyer and Seller relating to the Products, and no provision may be changed or waived unless in writing signed by the parties. 5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. High-frequency Relay G6W Certain Precautions on Specifications and Use 1. Suitability for Use. Seller shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in Buyer's application or use of the Product. At Buyer's request, Seller will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer shall take application responsibility in all cases but the following is a nonexhaustive list of applications for which particular attention must be given: (i) Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. (ii) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (iii) Use in consumer products or any use in significant quantities. (iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this product. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 2. Programmable Products. Seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof. 3. Performance Data. Performance data given in this publication is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to Seller's Warranty and Limitations of Liability. 4. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Seller representative at any time to confirm actual specifications of purchased Product. 5. Errors and Omissions. The information in this publication has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors, or omissions. 6. RoHS Compliance. Where indicated, our products currently comply, to the best of our knowledge as of the date of this publication, with the requirements of the European Union's Directive on the Restriction of certain Hazardous Substances ("RoHS"), although the requirements of RoHS do not take effect until July 2006. These requirements may be subject to change. Please consult our website for current information. Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ELECTRONIC COMPONENTS LLC 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 OMRON ON-LINE Global - http://www.omron.com USA - http://www.components.omron.com 847-882-2288 Cat. No. X302-E-1 08/09 Specifications subject to change without notice Printed in USA High-frequency Relay G6W