G6ZK-1P

High-frequency Relay G6Z Miniature 2.6-GHz-Band, SPDT, High-frequency Relay • Superior high-frequency characteristics include an isolation of 30 dB min., insertion loss of 0.5 dB max., and V.S.W.R. of 1.5 max. at 2.6 GHz. • Triplate micro stripline technology assures superior high-frequency characteristics. • Miniature dimensions of 20 x 8.6 x 8.9 mm (L x W x H). • E-shape or Y-shape terminal options with reverse contact arrangements available, allows greater freedom with PCB design. • Choose between 75-Ω or 50-Ω impedance models • RoHS Compliant. Ordering Information Classification Non-latching Structure Contact Terminal form arrangement Fully sealed SPDT E-shape Y-shape Single coil latching E-shape Y-shape Dual coil latching E-shape Y-shape Characteristic impedance 75 Ω 50 Ω 75 Ω 50 Ω 75 Ω 50 Ω 75 Ω 50 Ω 75 Ω 50 Ω 75 Ω 50 Ω Rated coil voltage 3, 4.5, 5, 9, 12, and 24 VDC G6Z-1PE G6Z-1PE-A G6Z-1P G6Z-1P-A G6ZU-1PE G6ZU-1PE-A G6ZU-1P G6ZU-1P-A G6ZK-1PE G6ZK-1PE-A G6ZK-1P G6ZK-1P-A Model Through-hole Surface Mount G6Z-1FE G6Z-1FE-A G6Z-1F G6Z-1F-A G6ZU-1FE G6ZU-1FE-A G6ZU-1F G6ZU-1F-A G6ZK-1FE G6ZK-1FE-A G6ZK-1F G6ZK-1F-A Notes: 1. When ordering, add the rated coil voltage to the model number. Example: G6Z-1PE-A-DC12 Rated coil voltage 2. When ordering tape packing (surface mount models), add "-TR" to the model number. Example: G6ZU-1FE-TR-DC12 Tape packing "-TR" is not part of the relay model number. Therefore, it is not marked on the relay case. Model Number Legend: G6Z 1 234 56 - DC 7 4. Terminal Structure None: Y-shape terminal E: E-shape terminal 6. Contact arrangement None: Standard contact arrangement R: Reverse contact arrangement 1. Relay Function None: Non-latching U: Single coil latching K: Dual coil latching 2. Contact Form 1: SPDT 3. Terminal Shape F: Surface mount terminals P: PCB through-hole terminals 5. Characteristic Impedance None: 75 Ω A: 50 Ω 7. Rated Coil Voltage 3, 4.5, 5, 9, 12, 24 High-frequency Relay G6Z 341 Application Examples These Relays can be used for switching signals in media equipment. • Wire communications: Cable TV (STB and broadcasting infrastructure), cable modems, and VRS (video response systems) • Wireless communications: Transceivers, ham radios, ETC, ITS, high-level TV, satellite broadcasting, text multiplex broadcasting, mobile phone stations, TV broadcasting facilities, community antenna systems and car navigation systems • Entertainment equipment: TVs, video games, satellite radio units, • Industrial equipment: Measuring equipment, test equipment, and multiplex transmission devices Specifications ■ Contact Ratings Load type Contact Material Rated load Rated carry current Max. switching voltage Max. switching current Resistive load Au clad Cu alloy 10 mA at 30 VAC; 10 mA at 30 VDC; 10 W at 900 MHz (See note) 0.5 A 30 VAC, 30 VDC 0.5 A Note: This value is for an impedance of 50 Ω or 75 Ω with a V.S.W.R. of 1.2 max. ■ High-frequency Characteristics Frequency Terminal type Terminal structure Isolation 75 Ω 50 Ω Insertion loss (not 75 Ω including substrate loss) 50 Ω V.S.W.R. Return loss Maximum carry power Maximum switching power 75 Ω 50 Ω 75 Ω 50 Ω Through hole E-shape 65 dB min. 60 dB min. 0.2 dB max. 0.1 dB max. 1.2 max. 1.1 max. 20.8 dB max. 26.4 dB max. 10 W (See note 2) 10 W (See note 2) 0.5 dB max. 0.3 dB max. 1.5 max. 1.3 max. 14.0 dB max. 17.7 dB max. Y-shape 900 MHz Surface mount E-shape 60 dB min. Y-shape Through hole E-shape Y-shape 2.6 GHz Surface mount E-shape Y-shape 35 dB min. 45 dB min. 30 dB min. 40 dB min. Note: 1. The above values are initial values. 2. These values are for an impedance of 50 Ω or 75 Ω with a V.S.W.R. of 1.2 max. 342 High-frequency Relay G6Z ■ Coil Ratings Non-latching, Standard and Reverse-contact Models G6Z-1P(E), G6Z-1F(E) Rated voltage (VDC) 3 4.5 5 9 12 24 66.7 44.4 40.0 22.2 16.7 8.3 Rated current (mA) 45 101 125 405 720 2,880 Coil resistance (Ω) Must operate voltage (VDC) 75% max. of rated voltage Must dropout voltage (VDC) 10% min. of rated voltage Maximum voltage (VDC) 150% of rated voltage Power consumption (mW) Approx. 200 Single Coil Latching Models G6ZU-1P(E), G6ZU-1F(E) Rated voltage (VDC) 3 4.5 5 9 12 24 66.7 44.4 40.0 22.2 16.7 8.3 Rated current (mA) 45 101 125 405 720 2,880 Coil resistance (Ω) Must set voltage (VDC) 75% max. of rated voltage Must reset voltage (VDC) 75% max. of rated voltage Maximum voltage (VDC) 150% of rated voltage Power consumption (mW) Approx. 200 Dual Coil Latching Models G6ZK-1P(E), G6ZK-1F(E) Rated voltage (VDC) 3 4.5 5 9 12 24 Note: 1. 2. 3. 4. 120 80 72 40 30 15 Rated current (mA) 25 56 69 225 400 1,600 Coil resistance (Ω) Must set voltage (VDC) 75% max. of rated voltage Must reset voltage (VDC) 75% max. of rated voltage Maximum voltage (VDC) 150% of rated voltage Power consumption (mW) Approx. 360 The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%. The operating characteristics are measured at a coil temperature of 23°C. The maximum voltage is the highest voltage that can be imposed on the relay coil instantaneously. The voltage measurements for operate/release and set/reset are the values obtained for instantaneous changes in the voltage (rectangular wave). High-frequency Relay G6Z 343 Characteristics Item Non-latching models G6Z-1P(E), G6Z-1F(E) Contact resistance (See note 2) Operating (set) time (See note 3) Release (reset) time (See note 3) Set/reset time Insulation resistance (See note 4) Dielectric strength Coil and contacts Coil and ground, contacts and ground Contacts of same polarity Vibration resistance Shock resistance Service life Mechanical durability Malfunction durability Mechanical durability Malfunction durability Mechanical Electrical Ambient temperature Ambient humidity Weight Note: 1. 2. 3. 4. 100 mΩ max. 10 ms max. (approx. 3.5 ms) 10 ms max. (approx. 2.5 ms) 10 ms max. (approx 2.5 ms) --100 MΩ min. (at 500 VDC) 1,000 VAC, 50/60 Hz for 1 min. 500 VAC, 50/60 Hz for 1 min. 500 VAC, 50/60 Hz for 1 min. 10 to 55 to 10 Hz, 0.75-mm single amplitude (1.5-mm double amplitude) 10 to 55 to 10 Hz, 0.75-mm single amplitude (1.5-mm double amplitude) 1,000 m/s2 500 m/s2 1,000,000 operations min. (at 36,000 operations/hour) 300,000 operations min. (30 VAC, 10 mA/30 VDC, 10 mA), 100,000 operations min. (900 MHz, 10 W) at a switching frequency of 1,800 operations/hour Operating: -40°C to 70°C (with no icing or condensation) Operating: 5% to 85% RH Approx. 2.8 g The above values are initial values. The contact resistance was measured with 10 mA at 1 VDC with a voltage drop method. Values in parentheses are typical values. The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those used for checking the dielectric strength. 12 ms Single coil latching models G6ZU-1P(E), G6ZU-1F(E) Dual coil latching models G6ZK-1P(E), G6ZK-1F(E) Engineering Data Ambient Temperature vs. Maximum Voltage Maximum voltage (%) 250 Ambient Temperature vs. Must Operate or Must Release Voltage On the basis of rated voltage (%) 100 Sample: G6Z-1P 5 VDC 90 Number of relays: 5 80 70 60 50 40 30 max. avg. min. Must operate voltage Must release voltage Shock Malfunction Y 1,000 800 max. avg. min. X 1,000 600 Not energized 400 200 Z 1,000 Energized Max. estimated value 200 G6Z G6ZU 150 200 1,000 Z' Shock direction X X' Y Z Z' Y' 400 600 800 1,000 m/s2 G6Z-1P-A 50 Ω 5 VDC Number of relays: 5 Unit: Sample: 1,000 X' G6ZK 100 50 20 10 Y' 0 −40 −20 0 20 40 60 80 100 0 −60 −40 −20 0 20 40 60 80 100 Ambient temperature (°C) Ambient temperature (°C) Conditions: Shock is applied in ±X, ±Y, and ±Z directions three times each with and without energizing the Relays to check for contact malfunctions. 344 High-frequency Relay G6Z Electrical Endurance (with Must Operate and Must Release Voltage) On the basis of rated voltage (%) 100 Sample: G6Z-1PE 75 Ω 5 VDC Number of Relays: 5 Test conditions: 10 mA resistive load at 30 VAC 80 Switching frequency: 1,800 operations/h Must operate 60 max. min. Electrical Endurance (with Must Operate and Must Release Voltage) On the basis of rated voltage (%) 100 Sample: G6Z-1PE 75 Ω 5 VDC Number of Relays: 5 Test conditions: 10 mA resistive load at 30 VDC 80 Switching frequency: 1,800 operations/h Must operate 60 max. min. 40 Must release 20 max. min. 40 Must release max. 20 min. 0 0.0001 0.001 0.01 0.1 1 10 100 0 0.0001 0.001 0.01 0.1 1 10 100 Operating frequency (×103 operations) Operating frequency (×103 operations) Electrical Endurance (Contact Resistance) Contact resistance (mΩ) 1,000 Sample: G6Z-1PE 75 Ω 5 VDC 700 Number of Relays: 5 500 Test conditions: 10 mA resistive load at 30 VAC Switching frequency: 1,800 operations/h 300 NO contact NC contact Electrical Endurance (Contact Resistance) Contact resistance (mΩ) 1,000 Sample: G6Z-1PE 75 Ω 5 VDC 700 Number of Relays: 5 500 Test conditions: 10 mA resistive load at 30 VDC Switching frequency: 1,800 operations/h 300 NO contact NC contact 100 Contact resistance 70 50 30 max. max. min. min. 100 70 Contact resistance 50 30 max. max. min. min. 10 0.001 0.01 0.1 1 10 100 1,000 (×103 operations) 10 0.001 0.01 0.1 1 10 100 1,000 Operating frequency Operating frequency (×103 operations) External Magnetic Interference (Average value) Change rate on the basis of initial value (%) Change rate on the basis of initial value (%) +30 S +20 N +30 S +20 N (Average value) Change rate on the basis of initial value (%) +30 S +20 N (Average value) +10 +10 +10 0 0 0 −10 −10 −10 −20 −30 −1,200 Sample: G6Z-1P 5 VDC Number of Relays: 5 −800 −400 0 400 Must operate voltage Must release voltage −20 −30 −1,200 Sample: G6Z-1P 5 VDC Number of Relays: 5 −800 −400 0 400 −20 Sample: G6Z-1P 5 VDC Number of Relays: 5 −30 −1,200 −800 −400 0 Must operate voltage Must release voltage Must operate voltage Must release voltage 800 1,200 800 1,200 400 800 1,200 External magnetic field (A/m) External magnetic field (A/m) External magnetic field (A/m) Note: 1. The tests were conducted at an ambient temperature of 23°C. 2. The contact resistance data are periodically measured reference values and are not values from monitoring each operation. Contact resistance values will vary according to the switching frequency and operating environment, so be sure to check operation under the actual operating conditions before use. High-frequency Relay G6Z 345 High-frequency Characteristics at 75 Ω (Isolation) (Average value (initial value)) Isolation (dB) 0 Sample: G6Z-1PE 75 Ω 5 VDC with terminating resistance High-frequency Characteristics at 75 Ω (Insertion Loss) (Average value (initial value)) Insertion loss (dB) 0 High-frequency Characteristics at 75 Ω (Return Loss, V.S.W.R.) (Average value (initial value)) Return loss (dB) 0 10 Return loss 20 1.5 V.S.W.R. V.S.W.R. Sample: G6Z-1PE 75 Ω 5 VDC with terminating resistance 1.7 1.6 20 0.2 40 0.4 30 1.4 60 0.6 40 V.S.W.R. 50 1.3 1.2 80 N.O. N.C. 0 500 1,000 1,500 2,000 2,500 3,000 0.8 Sample: G6Z-1PE 75 Ω 5 VDC with terminating resistance * Substrate loss removed 0 500 1,000 1,500 2,000 60 N.O .O. N.C .C. 2,500 3,000 70 N.O. N.C. 1.1 1 2,500 3,000 100 1.0 0 500 1,000 1,500 2,000 Frequency (MHz) Frequency (MHz) Frequency (MHz) High-frequency Characteristics at 50 Ω (Isolation) (Average value (initial value)) Isolation (dB) 0 Sample: G6Z-1PE-A 50 Ω 5 VDC with terminating resistance High-frequency Characteristics at 50 Ω (Insertion Loss) (Average value (initial value)) Insertion loss (dB) 0 High-frequency Characteristics at 50 Ω (Return Loss, V.S.W.R.) (Average value (initial value)) Return loss (dB) 0 10 Sample: G6Z-1PE-A 50 Ω 5 VDC with terminating resistance 1.7 1.6 20 0.2 20 Return loss 1.5 40 0.4 30 1.4 60 0.6 40 1.3 50 80 N.O. N.C. 0 500 1,000 1,500 2,000 2,500 3,000 0.8 V.S.W.R. Sample: G6Z-1PE-A 50 Ω 5 VDC with terminating resistance * Substrate loss removed 0 500 1,000 1,500 2,000 60 N.O. N.C. 2,500 3,000 70 N.O. N.C. 1.2 1.1 1 2,500 3,000 100 1.0 0 500 1,000 1,500 2,000 Frequency (MHz) Frequency (MHz) Frequency (MHz) Must Operate and Must Release Time Distribution (See note.) Number of contacts 25 Must operate Must release time Must Operate and Must Release Bounce Time Distribution (See note.) Number of contacts 30 Must operate bounce time Must release bounce time 20 Sample: G6Z-1P 75 Ω 5 VDC Number of Relays: 32 15 25 20 Sample: G6Z-1P 75 Ω 5 VDC Number of Relays: 32 15 10 10 5 5 0 1.0 2.0 3.0 4.0 5.0 0 0.5 1.0 1.5 2.0 Time (ms) Time (ms) Note: 1. The tests were conducted at an ambient temperature of 23°C. 2. High-frequency characteristics depend upon the PCB to which the relay is mounted. Always check these characteristics, including endurance (service life), in the actual machine before use. 346 High-frequency Relay G6Z Dimensions Note: All units are in millimeters unless otherwise indicated. ■ PCB Through-hole Terminal Types G6Z-1PE G6Z-1PE-R G6ZU-1PE Mounting Dimensions (Bottom View) Tolerance: ±0.1 mm Six, 1.8-dia. Terminal Arrangement/Internal Connections (Bottom View) G6Z-1PE Orientation mark 1 − + 7 Six, 1.0-dia. holes 7.62 Three, 1.6-dia. 14 20 8.6 2.54 7.62 15.24 Three, 0.8-dia. holes 13 12 11 10 9 8 8.9 Orientation mark 1 G6Z-1PE-R 7 − + 3 6-0.6 2.54 7.62 15.24 3-0.4 0.2 (Coil terminal) 0.18 7.62 14 13 12 11 10 9 8 G6ZU-1PE Orientation mark 1 S− R+ + − 7 Note: Each value has a tolerance of ±0.3 mm. 14 13 12 11 10 9 8 G6Z-1PE-A G6ZU-1PE-A Mounting Dimensions (Bottom View) Tolerance: ±0.1 mm Nine, 1.8-dia. Terminal Arrangement/Internal Connections (Bottom View) G6Z-1PE-A Orientation mark 1 − + 7 Nine, 1.0-dia. holes 7.62 20 8.6 14 2.54 7.62 15.24 13 12 11 10 9 8 8.9 Orientation mark 1 3 2.54 7.62 15.24 9-0.6 0.2 (Coil terminal) 0.18 7.62 14 G6ZU-1PE-A 7 S− R+ + − 13 12 11 10 9 8 Note: Each value has a tolerance of ±0.3 mm. High-frequency Relay G6Z 347 G6Z-1P G6ZU-1P Mounting Dimensions (Bottom View) Tolerance: ±0.1 mm Eight, 1.8-dia. Terminal Arrangement/Internal Connections (Bottom View) G6Z-1P Orientation mark 1 − 34 + 5 7 Eight, 1.0-dia. holes 7.62 Three, 1.6-dia. 14 20 8.6 2.54 7.62 15.24 Three, 0.8-dia. holes 13 12 10 9 8 8.9 Orientation mark 1 3 8-0.6 2.54 7.62 15.24 3-0.4 0.2 (Coil terminal) 0.18 7.62 14 G6ZU-1P 34 S− R+ + − 5 7 13 12 10 9 8 Note: Each value has a tolerance of ±0.3 mm. G6Z-1P-A G6ZU-1P-A Mounting Dimensions (Bottom View) Tolerance: ±0.1 mm Eleven, 1.8-dia. Terminal Arrangement/Internal Connections (Bottom View) G6Z-1P-A Orientation mark 1 − 34 + 5 7 Eleven, 1.0-dia. holes 7.62 20 8.6 14 2.54 7.62 15.24 13 12 10 9 8 8.9 Orientation mark 1 3 2.54 7.62 15.24 11-0.6 0.2 (Coil terminal) 0.18 7.62 14 G6ZU-1P-A 34 S− R+ + − 5 7 13 12 10 9 8 Note: Each value has a tolerance of ±0.3 mm. G6ZK-1PE Mounting Dimensions (Bottom View) Tolerance: ±0.1 mm Seven, 1.8-dia. Terminal Arrangement/Internal Connections (Bottom View) Orientation mark 1 − + S 6 7 Seven, 1.0-dia. holes 7.62 Three, 1.6-dia. 14 − + R 20 8.6 2.54 7.62 15.24 Three, 0.8-dia. holes 13 12 11 10 9 8 8.9 3 7-0.6 2.54 7.62 15.24 3-0.4 0.2 (Coil terminal) 0.18 7.62 Note: Each value has a tolerance of ±0.3 mm. 348 High-frequency Relay G6Z G6ZK-1PE-A Mounting Dimensions (Bottom View) Tolerance: ±0.1 mm Ten, 1.8-dia. Terminal Arrangement/Internal Connections (Bottom View) Orientation mark 1 − + S − + R 6 7 Ten, 1.0-dia. holes 7.62 20 8.6 14 2.54 7.62 15.24 13 12 11 10 9 8 8.9 3 2.54 7.62 15.24 10-0.6 0.2 (Coil terminal) 0.18 7.62 Note: Each value has a tolerance of ±0.3 mm. G6ZK-1P Mounting Dimensions (Bottom View) Tolerance: ±0.1 mm Nine, 1.8-dia. Terminal Arrangement/Internal Connections (Bottom View) Orientation mark 1 − 3 + S 4 − 5 + R 6 7 Nine, 1.0-dia. holes 7.62 Three, 1.6-dia. 14 20 8.6 2.54 7.62 15.24 Three, 0.8-dia. holes 13 12 10 9 8 8.9 3 9-0.6 2.54 7.62 15.24 3-0.4 0.2 (Coil terminal) 0.18 7.62 Note: Each value has a tolerance of ±0.3 mm. G6ZK-1P-A Mounting Dimensions (Bottom View) Tolerance: ±0.1 mm Twelve, 1.8-dia. Terminal Arrangement/Internal Connections (Bottom View) Orientation mark 1 − 3 + S 4 − 5 + R 6 7 Twelve, 1.0-dia. holes. 7.62 20 8.6 14 2.54 7.62 15.24 13 12 10 9 8 8.9 3 2.54 7.62 15.24 12-0.6 0.2 (Coil terminal) 0.18 7.62 Note: Each value has a tolerance of ±0.3 mm. High-frequency Relay G6Z 349 ■ Surface Mount Terminal Types G6Z-1FE G6ZU-1FE Mounting Dimensions (Top View) Tolerance: ±0.1 mm 15.24 7.62 2.54 0.8 0.8 0.8 2.3 − 1 20 8.6 8.3 + 7 Terminal Arrangement/Internal Connections (Top View) G6Z-1FE Orientation mark 14 13 12 11 10 9 8 9.3 0.2 (Coil terminal) 6-0.6 2.54 7.62 15.24 3-0.4 9.6 G6ZU-1FE Six, 1.1 0.18 Orientation mark 14 13 12 11 10 9 8 S− R+ 1 + − 7 Note 1: Each value has a tolerance of ±0.3 mm. 2: The coplanarity of the terminals is 0.1 mm max. G6Z-1FE-A G6ZU-1FE-A Mounting Dimensions (Top View) Tolerance: ±0.1 mm 15.24 7.62 2.54 2.3 Terminal Arrangement/Internal Connections (Top View) G6Z-1FE-A Orientation mark 14 13 12 11 10 9 8 − 1 + 7 8.3 20 8.6 9.3 0.2 (Coil terminal) 2.54 7.62 15.24 9-0.6 9.6 Nine, 1.1 0.18 G6ZU-1FE-A Orientation mark 14 13 12 11 10 9 8 S− R+ 1 + − 7 Note 1: Each value has a tolerance of ±0.3 mm. 2: The coplanarity of the terminals is 0.1 mm max. G6Z-1F G6ZU-1F Mounting Dimensions (Top View) Tolerance: ±0.1 mm 15.24 2.54 0.8 0.8 2.3 Terminal Arrangement/Internal Connections (Top View) G6Z-1F Orientation mark 14 13 12 10 9 8 − 1 + 34 5 7 8.3 20 8.6 9.3 0.2 (Coil terminal) 8-0.6 2.54 7.62 15.24 3-0.4 9.6 Eight, 1.1 0.18 0.8 7.62 G6ZU-1F Orientation mark 14 13 12 10 9 8 S− R+ 1 + − 34 5 7 Note 1: Each value has a tolerance of ±0.3 mm. 2: The coplanarity of the terminals is 0.1 mm max. 350 High-frequency Relay G6Z G6Z-1F-A G6ZU-1F-A Mounting Dimensions (Top View) Tolerance: ±0.1 mm 15.24 2.54 2.3 Terminal Arrangement/Internal Connections (Top View) G6Z-1F-A Orientation mark 14 13 12 10 9 8 − 8.3 1 20 8.6 Eleven, 1.1 9.3 0.2 (Coil terminal) 2.54 7.62 15.24 1 11-0.6 9.6 7.62 0.18 Orientation mark 14 + 34 5 7 G6ZU-1F-A 13 12 10 9 8 S− R+ + − 34 5 7 Note 1: Each value has a tolerance of ±0.3 mm. 2: The coplanarity of the terminals is 0.1 mm max. G6ZK-1FE Mounting Dimensions (Top View) Tolerance: ±0.1 mm 15.24 7.62 2.54 0.8 20 8.6 8.3 0.8 0.8 2.3 Terminal Arrangement/Internal Connections (Top View) Orientation mark 14 13 12 11 − + S− 10 9 8 1 + R 6 7 9.3 0.2 (Coil terminal) 7-0.6 2.54 7.62 15.24 3-0.4 9.6 0.18 Seven, 1.1 Note 1: Each value has a tolerance of ±0.3 mm. 2: The coplanarity of the terminals is 0.1 mm max. G6ZK-1FE-A Mounting Dimensions (Top View) Tolerance: ±0.1 mm 15.24 7.62 2.54 2.3 Terminal Arrangement/Internal Connections (Top View) Orientation mark 14 13 12 11 − + S− 10 9 8 20 8.6 8.3 1 + R 6 7 9.3 0.2 (Coil terminal) 2.54 7.62 15.24 Ten, 0.6 9.6 0.18 Ten, 1.1 Note 1: Each value has a tolerance of ±0.3 mm. 2: The coplanarity of the terminals is 0.1 mm max. High-frequency Relay G6Z 351 G6ZK-1F Mounting Dimensions (Top View) Tolerance: ±0.1 mm 15.24 7.62 2.54 0.8 0.8 2.3 Terminal Arrangement/Internal Connections (Top View) Orientation mark 14 13 12 − + S 34 10 9 8 − + R 56 7 20 8.6 8.3 1 9.3 0.2 (Coil terminal) Nine, 0.6 0.18 9.6 Nine, 1.1 0.8 2.54 7.62 Three, 0.4 15.24 Note 1: Each value has a tolerance of ±0.3 mm. 2: The coplanarity of the terminals is 0.1 mm max. G6ZK-1F-A Mounting Dimensions (Top View) Tolerance: ±0.1 mm 15.24 7.62 2.54 2.3 Terminal Arrangement/Internal Connections (Top View) Orientation mark 14 13 12 − + S 34 10 9 8 − + R 56 7 20 8.6 8.3 1 9.3 0.2 (Coil terminal) 2.54 7.62 15.24 Twelve, 0.6 0.18 9.6 Twelve, 1.1 Note 1: Each value has a tolerance of ±0.3 mm. 2: The coplanarity of the terminals is 0.1 mm max. 352 High-frequency Relay G6Z Packaging 1. Tube Packaging Relays in tube packaging are arranged so that the orientation mark of each Relay in on the left side. Be sure not to make mistakes in Relay orientation when mounting the Relay to the PCB. Operation of Relays Stopper (gray) Stopper (green) A Reel Dimensions 33.5±1 37.5±1 13±0.2 dia. 2±0.5 21±0.8 dia. 330 80 R1 Enlarged view of A Tube length: 530 mm (stopper not included) No. of Relays per tube: 25 2. Tape and Reel Packaging (Surface mount Terminal Models) When ordering Relays in tape packing, add the prefix “-TR” to the model number, otherwise the Relays in stick packing will be provided. Relays per Reel: 300 Carrier Tape Dimensions 2±0.1 16±0.1 4±0.1 10±0.1 0.1 1.5+0 dia. 1.75±0.1 0.5±0.05 14.2±0.1 28.4±0.1 22.6±0.1 20.6±0.1 32±0.3 Direction of Relay Insertion Pulling direction Orientation mark Top tape (cover tape) Pulling direction 5° max. 10.2±0.1 4±0.1 A 0.2 0.1 1.5+0 5° max. 0.15 1.7+0 R0.75 Enlarged view of A Note: The radius of the unmarked corner is 0.3 mm. Carrier tape Emboss tape Recommended Soldering Method ■ Temperature Conditions for IRS Method When using reflow soldering, ensure that the Relay terminals and the top of the case stay below the following curve. Check that these conditions are actually satisfied before soldering the terminals. Temperature Do not quench the terminals after mounting. Clean the Relay using alcohol or water no hotter than 40°C max. The thickness of cream solder to be applied should be between 150 and 200 μm on OMRON’s recommended PCB pattern. Correct Soldering Relay T4 T3 Incorrect Soldering T2 PCB T1 Terminal Solder Land Insufficient amount of solder Excessive amount of solder Check the soldering in the actual mounting conditions before use. t1 Preheating t2 Soldering Time Measured part Terminals Top of case Preheating (T1 → T2, t1) 150 → 180°C, 120 s max. --- Soldering (T3, t2) 230°C min, 30 s max. --- Maximum peak (T4) 250°C max. 255°C max. High-frequency Relay G6Z 353 Safety Precautions ■ Precautions for Correct Use Please observe the following precautions to prevent failure to operate, malfunction, or undesirable effect on product performance. Substrate for High-frequency Characteristic Compensation (75-Ω Models, E-shape or Y-shape) (Unit: mm) 30.7 20 4-dia. through-hole High-frequency Characteristics Measurement Method and Measurement Substrate High-frequency characteristics for the G6Z are measured in the way shown below. Consult your OMRON representative for details on 50-Ω models. Measurement Method for 75-Ω Models G6Z Network vector analyzer (Agilent Technologies) HP8753D 50Ω/75Ω adapter (Agilent Technologies) 11852B-004 0.6-dia. through-hole 0.95 40 30 1 75-Ω terminating resistance Substrate Types Material: FR-4 glass epoxy (glass cloth impregnated with epoxy resin and copper laminated to its outer surface) Thickness: 1.6 mm Thickness of copper plating:18 μm Through-hole Substrate (75-Ω Models, E-shape or Y-shape) 40 30 4-dia. through-hole Note: (Unit: mm) 0.4 1.4 Note: Note: 3.59 Note: 40 30 6.3 1 0.95 Note: 1. The compensation substrate is used when measuring the Relay’s insertion loss. The insertion loss is obtained by subtracting the measured value for the compensation substrate from the measured value with the Relay mounted to the high-frequency measurement substrate. 2. For convenience, the diagrams of the high-frequency measurement substrates given here apply both to models with an E-shape terminal structure and to models with a Y-shape terminal structure. 3. Be sure to mount a standoff tightly to the through-hole substrate. 4. Use measuring devices, connectors, and substrates that are appropriate for 50 Ω and 75 Ω respectively. 5. Ensure that there is no pattern under the Relay. Otherwise, the impedance may be adversely affected and the Relay may not be able to attain its full characteristics. Handling 0.6-dia. through-hole Do not use the Relay if it has been dropped. Dropping the Relay may adversely affect its functionality. SMD-type Substrate (75-Ω Models, E-shape or Y-shape) 40 30 1.4 (Unit: mm) 0.4 4-dia. through-hole Protect the Relay from direct sunlight and keep the Relay under normal temperature, humidity, and pressure. Flow Soldering Solder: JIS Z3282, H63A Soldering temperature: Approx. 250°C (260°C if the DWS method is used) 0.6-dia. through-hole Soldering time: Approx. 5 s max. (approx. 2 s for the first time and approx. 3 s for the second time if the DWS method is used) Be sure to make a molten solder level adjustment so that the solder will not overflow on the PCB. 40 30 6.3 3.91 0.95 1 354 High-frequency Relay G6Z Claw Securing Force During Automatic Mounting During automatic insertion of Relays, be sure to set the securing force of each claw to the following so that the Relay’s characteristics will be maintained. A B Direction A: 4.90 N max. Direction B: 4.90 N max. Direction C: 4.90 N max. Secure the claws to the shaded area. Do not attach them to the center area or to only part of the Relay. Latching Relay Mounting Make sure that the vibration or shock that is generated from other devices, such as Relays, on the same panel or substrate and imposed on the Latching Relay does not exceed the rated value, otherwise the set/reset status of the Latching Relay may be changed. The Latching Relay is reset before shipping. If excessive vibration or shock is imposed, however, the Latching Relay may be set accidentally. Be sure to apply a reset signal before use. Coating Do not use silicone coating to coat the Relay when it is mounted to the PCB. Do not wash the PCB after the Relay is mounted using detergent containing silicone. Otherwise, the detergent may remain on the surface of the Relay. High-frequency Relay G6Z 355 MEMO 356 High-frequency Relay G6Z Omron Electronic Components, LLC Terms and Conditions of Sales I. GENERAL 1. Definitions: The words used herein are defined as follows. (a) Terms: These terms and conditions (b) Seller: Omron Electronic Components LLC and its subsidiaries (c) Buyer: The buyer of Products, including any end user in section III through VI (d) Products: Products and/or services of Seller (e) Including: Including without limitation 2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments, invoices, purchase orders and other documents, whether electronic or in writing, relating to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's purchase order or other documents which are inconsistent with, or in addition to, these Terms. 3. Distributor: Any distributor shall inform its customer of the contents after and including section III of these Terms. II. SALES 1. Prices; Payment: All prices stated are current, subject to change without notice by Seller. Buyer agrees to pay the price in effect at the time the purchase order is accepted by Seller. Payments for Products received are due net 30 days unless otherwise stated in the invoice. Buyer shall have no right to set off any amounts against the amount owing in respect of this invoice. 2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to Buyer after deducting transportation charges, taxes and duties, and will be allowed only if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past due amounts owing to Seller. 3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum legal rate, whichever is less, on any balance not paid within the stated terms. 4. Orders: Seller will accept no order less than 200 U.S. dollars net billing. 5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer shall make remittance to Seller at the then current exchange rate most favorable to Seller; provided that if remittance is not made when due, Buyer will convert the amount to U.S. dollars at the then current exchange rate most favorable to Seller available during the period between the due date and the date remittance is actually made. 6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining any government approvals regarding the importation or sale of the Products. 7. Taxes: All taxes, duties and other governmental charges (other than general real property and income taxes), including any interest or penalties thereon, imposed directly or indirectly on Seller or required to be collected directly or indirectly by Seller for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by Buyer to Seller. 8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller, Seller reserves the right to stop shipments or require satisfactory security or payment in advance. If Buyer fails to make payment or otherwise comply with these Terms or any related agreement, Seller may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid accounts. 9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer indemnifies Seller fully against all costs or expenses arising in connection therewith. 10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller: (a) All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Seller), at which point title to and all risk of loss of the Products shall pass from Seller to Buyer, provided that Seller shall retain a security interest in the Products until the full purchase price is paid by Buyer; (b) Delivery and shipping dates are estimates only; and (c) Seller will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions. 12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products occurring before delivery to the carrier or any claim related to pricing or other charges must be presented in detail in writing to Seller within 30 days of receipt of shipment. III. PRECAUTIONS 1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E) SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT. Buyer acknowledges that it alone has determined that the Products will meet their requirements of the intended use in all cases. Buyer must know and observe all prohibitions of use applicable to the Product/s. 2. Use with Attention: The followings are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible use of any Product, nor to imply that any use listed may be suitable for any Product: (a) Outdoor use, use involving potential chemical contamination or electrical interference. (b) Use in consumer Products or any use in significant quantities. (c) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (d) Systems, machines, and equipment that could present a risk to life or property. 3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY SELLER. 5. Programmable Products: Seller shall not be responsible for the Buyer's programming of a programmable Product. IV. WARRANTY AND LIMITATION 1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Seller (or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES, NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. 2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an amount equal to the purchase price of the Product; provided that there shall be no liability for Seller or its affiliates unless Seller's analysis confirms that the Products were correctly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Seller before shipment. 3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF THE PRODUCT ON WHICH LIABILITY IS ASSERTED. 4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its employees from and against all liabilities, losses, claims, costs and expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or omissions under these Terms or in any way with respect to the Products. V. INFORMATION; ETC. 1. Intellectual Property: The intellectual property embodied in the Products is the exclusive property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way without the written permission of Seller. Buyer (at its own expense) shall indemnify and hold harmless Seller and defend or settle any action brought against Seller to the extent that it is based on a claim that any Product made to Buyer specifications infringed intellectual property rights of another party. 2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or tooling, all engineering and tooling shall remain the exclusive property of Seller. All information and materials supplied by Seller to Buyer relating to the Products are confidential and proprietary, and Buyer shall limit distribution thereof to its trusted employees and strictly prevent disclosure to any third party. 3. Performance Data: Performance data is provided as a guide in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must correlate it to actual application requirements. 4. Change In Specifications: Product specifications and descriptions may be changed at any time based on improvements or other reasons. It is Seller’s practice to change part numbers when published ratings or features are changed, or when significant engineering changes are made. However, some specifications of the Product may be changed without any notice. 5. Errors And Omissions: The information on Seller’s website or in other documentation has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses regarding (a) export of the Products or information provided by Seller; (b) sale of Products to forbidden or other proscribed persons or organizations; (c) disclosure to noncitizens of regulated technology or information. VI. MISCELLANEOUS 1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing between Buyer and Seller shall operate as a waiver of rights by Seller. 2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent. 3. Law: These Terms are governed by Illinois law (without regard to conflict of laws). Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any dispute hereunder. 4. Amendment: These Terms constitute the entire agreement between Buyer and Seller relating to the Products, and no provision may be changed or waived unless in writing signed by the parties. 5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. High-frequency Relay G6Z Certain Precautions on Specifications and Use 1. Suitability for Use. Seller shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in Buyer's application or use of the Product. At Buyer's request, Seller will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer shall take application responsibility in all cases but the following is a nonexhaustive list of applications for which particular attention must be given: (i) Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. (ii) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (iii) Use in consumer products or any use in significant quantities. (iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this product. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 2. Programmable Products. Seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof. 3. Performance Data. Performance data given in this publication is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to Seller's Warranty and Limitations of Liability. 4. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Seller representative at any time to confirm actual specifications of purchased Product. 5. Errors and Omissions. The information in this publication has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors, or omissions. 6. RoHS Compliance. Where indicated, our products currently comply, to the best of our knowledge as of the date of this publication, with the requirements of the European Union's Directive on the Restriction of certain Hazardous Substances ("RoHS"), although the requirements of RoHS do not take effect until July 2006. These requirements may be subject to change. Please consult our website for current information. Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ELECTRONIC COMPONENTS LLC 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 OMRON ON-LINE Global - http://www.omron.com USA - http://www.components.omron.com 847-882-2288 Cat. No. X302-E-1 08/09 Specifications subject to change without notice Printed in USA High-frequency Relay G6Z