New Product
I/O Relay Terminal
G70V
I/O Relay Terminals with 16 Points and
Push-In Plus terminal blocks to
Downsize Control Panels and Save
Labor
• I/O Relay Terminals with 16 points to mount G2RV Slim I/O
Relays.
• Push-In Plus terminal blocks are used to save wiring work in
comparison with traditional screw terminals. (Wiring time is reduced
by 60%* in comparison with traditional screw terminals.)
• Work is reduced ever further with one-step cable connection
For the most recent information on models that have been
to the PLC.
certified for safety standards, refer to your OMRON website.
• Diode provided for coil surge absorption.
• Operation indicators for immediate recognition of I/O signal
status.
• Accepts G3RV Slim I/O SSRs.
• Greatly reduce wiring work and maximize space efficiency with new models that provide internal connections
between I/O terminals. (input models: 16 point/common, output models: 4 points/common)
• DIN Track or screw mounting.
* According to OMRON actual measurement data from November 2015.
Refer to Safety Precautions on page 17.
Model Number Legend
G70V - @ @ @ 16 P - @- @
(1) (2) (3) (4) (5) (6) (7)
(1) Mountable Relays
S: Relays
Z: Sockets
(2) Input/Output Classification
I: For input
O: For output
(3) I/O Specification
C: Contacts
(Applicable when (2) is O (for output) (relay output).)
D: DC (Applicable when (2) is I (for input) (coil for input).)
M: AC/DC (Applicable when (1) is Z (Sockets).)
(4) Number of I/O Points
16: 16 points
(5) Terminal Type
P: Push-In Plus terminal blocks
(6) Common Line on Connector Side
Blank: NPN
1: PNP
(7) Common Line on Terminal Block Side
Blank: No internal connections
C4:
Every 4 points internally connected at terminal
block bottom row
C4-D: Every 4 points internally connected at terminal
block middle row
C16: 16 points internally connected
(For Input NPN)
PLC
(For Input PNP)
G70V
(+)
PLC
G70V
)+(
−
Common
)−(
(−)
(For Output NPN)
+ Common
(For Output PNP)
PLC
G70V
PLC
(+)
NPN
transistor
X
+
(−)
G70V
(+)
−
X
Common
PNP
transistor
Common
X
X
(−)
1
G70V
Ordering Information
I/O Relay Terminals
Terminals
Classification
Common Line
Terminal Block Side
Points
No internal connections
Input *1
16 points internally connected
Push-In Plus
terminal blocks
16
No internal connections
Output *2
Every 4 points internally connected
at terminal block bottom row
Connector Side
NPN (– common)
PNP (+ common)
NPN (– common)
PNP (+ common)
NPN (+ common)
PNP (– common)
NPN (+ common)
PNP (– common)
Rated
voltage
Model
24 VDC
G70V-SID16P
G70V-SID16P-1
G70V-SID16P-C16
G70V-SID16P-1-C16
G70V-SOC16P
G70V-SOC16P-1
G70V-SOC16P-C4
G70V-SOC16P-1-C4
*1. Mountable Relays: G2RV-1-S-AP-G DC21V.
*2. Mountable Relays: G2RV-1-S-G DC21V.
I/O Terminal Sockets
Applicable I/O Relay Terminal
Common Line
Classification
G70V-SID16P
G70V-SID16P-1
G70V-SID16P-C16
G70V-SID16P-1-C16
G70V-SOC16P
G70V-SOC16P-1
G70V-SOC16P-C4
G70V-SOC16P-1-C4
Terminal Block Side
Connector Side
No internal connections
Input
16 points internally connected
No internal connections
Every 4 points internally connected
at terminal block bottom row
Output
Every 4 points internally connected
at terminal block middle row
--- *
NPN (– common)
PNP (+ common)
NPN (– common)
PNP (+ common)
NPN (+ common)
PNP (– common)
NPN (+ common)
PNP (– common)
NPN (+ common)
PNP (– common)
Model
G70V-ZID16P
G70V-ZID16P-1
G70V-ZID16P-C16
G70V-ZID16P-1-C16
G70V-ZOM16P
G70V-ZOM16P-1
G70V-ZOM16P-C4
G70V-ZOM16P-1-C4
G70V-ZOM16P-C4-D
G70V-ZOM16P-1-C4-D
Note: Relays are not mounted to the G70V-ZID/ZOM16P(-1) I/O Terminal Sockets. Combine the I/O Terminal Sockets with Slim I/O Relays or Slim I/O SSRs.
* The G70V-ZOM16P(-1)-C4-D does not come with SSRs. Use Slim I/O SSRs (for DC: G3RV-D03SL).
Options (Order Separately)
Mountable Relays
Applicable I/O Relay Terminal
Classification
G70V-SID16P(-1)(-C16)
G70V-ZID16P(-1)(-C16)
Type
Slim I/O Relays *1
Input
Slim I/O Relays
G70V-SOC16P(-1)(-C4)
G70V-ZOM16P(-1)(-C4)
Output
G70V-ZOM16P(-1)-C4-D *3
Output
Model
Slim I/O SSRs
Slim I/O SSRs
G2RV-1-S-AP-G DC21
No Latching Lever *2
Latching Lever
Zero cross function
For AC
No zero cross function
For DC
For DC
G2RV-1-S-G DC21
G2RV-1-SI-G DC21
G3RV-202S DC24
G3RV-202SL DC24
G3RV-D03SL DC24
G3RV-D03SL DC24
Note: To use Slim I/O SSRs, either remove the Slim I/O Relays to mount them or order a I/O Terminal Sockets and I/O SSRs separately and
combine them.
*1. G2RV-1-S-AP-G Slim I/O Relays are mounted to G70V-SID16P(-1)(-C16) I/O Relay Terminals as a standard feature.
*2. G2RV-1-S-G Slim I/O Relays are mounted to G70V-SOC16P(-1)(-C4) I/O Relay Terminals as a standard feature.
*3. The G70V-ZOM16P(-1)-C4-D does not come with SSRs. Use Slim I/O SSRs (for DC: G3RV-D03SL).
When ordering, designate the rated voltage.
Cables for I/O Relay Terminals XW2Z-R
• Cable with Loose Wire and Crimp Terminals:
• Cable with Loose Wires:
• Cable with connectors
• Fujitsu connectors
(1:1):
(1:2):
(1:3):
XW2Z-RY@C
XW2Z-RA@C
XW2Z-R@C
XW2Z-RI@C-@
XW2Z-RO@C-@
XW2Z-R@C-@-@
• MIL connectors
(1:2):
Refer to Connecting Cables on page 19 for details.
Labels
Appearance
2
(1:1):
Model
Minimum order (sheet)
(quantity per sheet)
XW5Z-P2.5LB2
5
(1 sheet / 72 pieces)
XW2Z-RI@C
XW2Z-RO@C
XW2Z-RI@-@-D@
XW2Z-RM@-@-D@
XW2Z-RO@-@-D1
G70V
Accessories for DIN Track Mounting
Appearance
Name
Minimum order
(quantity)
Model
1m
PFP-100N
0.5 m
PFP-50N
DIN Tracks
1
PFP-M *
End Plate
10
PFP-S *
Spacer
* These products must be ordered in sets of 10.
Option Mounting Example
Mounting to DIN Track
Label
Enlarged view
DIN Track
PFP-100N (1 m)
PFP-50N (50 cm)
End Plate
PFP-M
Specifications
Coil Ratings (Common to Input/Output per Relay)
Item
Must
Must
Maximum
Power
operate of
release of rated voltage of rated consumption
rated voltage
voltage
voltage
(mW)
13.3
1575
80% max.
10% min.
110%
Approx. 280
The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±15% for coil resistance.
The operating characteristics are measured at a coil temperature of 23°C.
The value for maximum voltage is the maximum value within the allowable voltage fluctuation range for the relay coil’s operating power
supply. Continuous operation at this voltage is not within product specifications.
The rated current includes the current for the indicators on the I/O Relay Terminal.
Rated voltage (V)
24 VDC
Note: 1.
2.
3.
4.
Rated current
(mA)
Coil resistance
(Ω)
Contact Ratings (G2RV-1-S-G I/O Relay)
Classification
Item
For input
Resistive load (cosφ=1)
Resistive load (cosφ=1)
Inductive load
(cosφ=0.4 L/R=7 ms)
2.5 A at 250 VAC
2 A at 30 VDC
6 A at 250 VAC
6 A at 30 VDC
Rated carry current
6 A/point, 10 A/common
Max. switching voltage
250 VAC, 125 VDC
Max. switching current
6 A/point, 10 A/common
1,500 VA
500 VA
Maximum switching capacity --180 W
60 W
Error rate (reference value) * 1 mA at 100 mVDC
10 mA at 5 VDC
NO contacts: 70,000 operations min.
Electrical endurance
5,000,000 operations min.
NC contacts: 50,000 operations min.
Mechanical endurance
5,000,000 operations min.
5,000,000 operations min.
* The above values are for a switching frequency of 120 operations/min.
Rated load
50 mA at 30 VAC
50 mA at 36 VDC
50 mA
30 VAC, 36 VDC
50 mA
For output
3
G70V
Characteristics
Model
Item
G70V-SID16P(-1)(-C16)
(Input, DC coil)
SPST-NO × 16
Ag alloy + Au plating
150 mΩ max.
20 ms max.
40 ms max.
18,000 operations/h
G70V-SOC16P(-1)(-C4)
(output, DC coil)
Contact form
Contact material
Contact resistance *1
Must Operate time *2
Release time *2
Max.
Mechanical limit
switching
At rated load
1,800 operations/h (under rated load)
frequency
Insulation resistance
100 MΩ min.
Dielectric strength
Between coil and contacts: 2,500 VAC for 1 min
Vibration resistance
100 m/s2
Shock resistance
100 m/s2, 3 times each in 6 directions along 3 axes
Noise immunity
Noise level: 1.5 kV; pulse width: 100 ns to 1 μs
Ambient operating
−40 to 55°C (with no icing or condensation)
temperature
Ambient operating humidity
35% to 85%
Power supply
Green
LED color
I/O
Yellow
Weight
Approx. 350 g
Note: The above values are initial values.
*1. Measurement: 1 A at 5 VDC.
*2. Ambient temperature: 23°C.
SPDT × 16
Ag alloy
Approx. 370 g
Approved Standards
The rated values for safety standard certification are not the same as individually defined performance values. Always check the specifications
before use.
UL standard certification (File No. E95399)
Type
I/O Relay Terminal
I/O Terminal Sockets
Model
G70V-SID16P(-1)
G70V-SID16P(-1)-C16
G70V-SOC16P(-1)
G70V-SOC16P(-1)-C4
G70V-ZID16P(-1)
G70V-ZID16P(-1)-C16
G70V-ZOM16P(-1)
G70V-ZOM16P(-1)-C4
G70V-ZOM16P(-1)-C4-D
Ratings
Standard number
Category
Listed/Recognized
Contact ratings
24V DC
Listed
24V DC
USL: UL 61010-1-12
CNL: UL 61010-2-201
250V AC / 30V DC
Resistive 4A at 40°C
NRAQ,
NRAQ7
24V DC
Recognized
250V AC / 30V DC
Resistive 4A at 40°C
Note: 1. USL refers to certification in the US, and CNL refers to certification in Canada.
2. cULus certification has been obtained in Canada. (CAN/CSA-C22.2 No. 61010-2-201)
TÜV Rheinland certification (Certification No. R50327604)
Type
Model
G70V-SID16P(-1)
G70V-SID16P(-1)-C16
Ratings
Standard number
Operating coil
24V DC 0.05A L/R=0ms
G70V-SOC16P(-1)
I/O Relay Terminal
24V DC
EN 61810-1
24V DC
G70V-SOC16P(-1)-C4
G70V-ZID16P(-1)
G70V-ZID16P(-1)-C16
single load: 250V AC 6A cos(phi)=1
16 loads: 250V AC 3A cos(phi)=1
16 loads: 30V DC 3A L/R=0ms
16 loads: 250V AC 5A cos(phi)=1 (Ta=+25°C)
16 loads: 30V DC 5A L/R=0ms (Ta=+25°C)
250V AC / 30V DC
16 loads: 5A (Ta=+25°C)
16 loads: 3A (Ta=+55°C)
1 load: 6A
Resistive load
total max. 10A common line
24V DC 0.05A L/R=0ms
G70V-ZOM16P(-1)
I/O Terminal Sockets
Contact ratings
24V DC
EN 61810-1
G70V-ZOM16P(-1)-C4
G70V-ZOM16P(-1)-C4-D
24V DC
single load: 250V AC 6A cos(phi)=1
16 loads: 250V AC 3A cos(phi)=1
16 loads: 30V DC 3A L/R=0ms
16 loads: 250V AC 5A cos(phi)=1 (Ta=+25°C)
16 loads: 30V DC 5A L/R=0ms (Ta=+25°C)
250V AC / 30V DC
16 loads: 5A (Ta=+25°C)
16 loads: 3A (Ta=+55°C)
1 load: 6A
Resistive load
total max. 10A common line
CE Marking Compliance
Model
G70V
EMC Directive
Not applicable
Low Voltage Directive
❍
Machinery Directive
Not applicable
Note: 1. The Safety Category refers to the maximum applicable category selected when constructing control system safety components. The
category does not apply to individual components.
2. Details and other information on conformity levels are issued as part of the "EU Declaration of Conformity." Please contact your OMRON
representative for more information.
4
G70V
Engineering Data (Reference Value)
Operations (× 103)
Endurance Curve (NO Contacts)
G70V-SOC16P(-1)(-C4)
1000
30 VDC resistive load
250 VAC resistive load
100
30 VDC
inductive load
250 VAC inductive load
10
0
2
4
6
Switched current (A)
Note: These data are actual measured values that were sampled from the production line and prepared in graph format, and are for reference
purposes only. A relay is manufactured by mass production, and as a basic rule must be used with allowance made for a certain amount of
deviation.
Load Current vs. Ambient Temperature
G3RV-202S DC24
G70V-SOC16P(-1)(-C4)
G3RV-D03 DC24
(A)
Single Relay
6
16 points ON
5
(A)
Load Current (A)
Load Current (A)
Load Current (A)
G3RV-202SL DC24
3
4
(A)
3
Single Relay
Single Relay
2
2
3
16 points ON
16 points ON
2
1
1
1
0.5
0.2
0
-40
-20
0
0
-40
20 25
40
55 60
Ambient Temperature
-20
0
20 25
40 55 60
Ambient Temperature
0
-40
-20
0
20
40 55 60
Ambient Temperature
Inrush Current Resistance: Non-repetitive
The following graphs show the maximum inrush currents that can be withstood for non-repetitive operation.
For repetitive operation, the figures should be reduced by half.
G3RV-D03 DC24
Inrush current (A. Peak)
Inrush current (A. Peak)
G3RV-202S DC24
G3RV-202SL DC24
40
35
30
25
40
35
30
25
20
20
15
15
10
10
5
5
0
10
30 50
100
300 500 1,000
3,000 5,000
Energized time (ms)
0
10
30 50
100
300 500 1,000
3,000 5,000
Energized time (ms)
5
G70V
Internal Circuits
G70V-SID16P
(NPN input/– common)
10
Connector Pin Configuration
Top View
20
Relay No.
1
2
3
4
5
6
7
8
+
−
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
+
−
Connector
pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
9
19
X Input relays
G2RV-1-S-AP-G
X
V
V
X
V
G G
G
Push-in power supply terminals
X
X
X
X
X
X
X
X
X
X
X
X
X
X
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Push-in I/O terminals
mark
Connector pin No.
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
Terminal name
Description
V (push-in power supply terminals)
Unit power supply terminals (24 VDC)
G (push-in power supply terminals)
V (push-in I/O terminals)
Relay-drive coil terminals (24 VDC)
G (push-in I/O terminals)
G70V-SID16P-1
(PNP input/+ common)
Connector Pin Configuration
Top View
10
20
Relay No.
1
2
3
4
5
6
7
8
−
+
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
−
+
mark
Connector pin No.
Connector
pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
9
19
X Input relays
G2RV-1-S-AP-G
X
V
V
X
V
G G
G
Push-in power supply terminals
X
X
X
X
X
X
X
X
X
X
X
X
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Terminal name
G (push-in power supply terminals)
V (push-in I/O terminals)
G (push-in I/O terminals)
6
X
G
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
V (push-in power supply terminals)
X
Description
Unit power supply terminals (24 VDC)
Relay-drive coil terminals (24 VDC)
Push-in I/O terminals
G70V
G70V-SID16P-C16
(NPN input/– common)
Connector Pin Configuration
Top View
10
20
Relay No.
1
2
3
4
5
6
7
8
+
−
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
+
−
Connector
pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
9
19
X
V
mark
Connector pin No.
X
V
G G
Push-in power
supply terminals
X
X
X
X
X
X
X
X
X
X
X
X
X
X Input relays
X
G2RV-1-S-AP-G
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Push-in I/O terminals
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
Terminal name
Description
V (push-in power supply terminals)
Unit power supply terminals (24 VDC)
G (push-in power supply terminals)
V (push-in I/O terminals)
Relay-drive coil terminals (24 VDC)
G (push-in I/O terminals)
G70V-SID16P-1-C16
(PNP input/+ common)
Connector Pin Configuration
Top View
10
20
Relay No.
1
2
3
4
5
6
7
8
−
+
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
−
+
Connector
pin No.
mark
Connector pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
9
19
X
V
V
G G
Push-in power
supply terminals
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X Input relays
X
G2RV-1-S-AP-G
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Push-in I/O terminals
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
Terminal name
V (push-in power supply terminals)
G (push-in power supply terminals)
V (push-in I/O terminals)
G (push-in I/O terminals)
Description
Unit power supply terminals (24 VDC)
Relay-drive coil terminals (24 VDC)
7
G70V
G70V-SOC16P
(NPN output/+ common)
Note: A controller with an NPN transistor, common output can be connected to the G70V-SOC16P.
Connector Pin Configuration
Top View
X Output relays
G2RV-1-S-G
Relay No.
1
2
3
4
5
6
7
8
−
+
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
−
+
Connector
pin No.
mark
Connector pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
10
20
9
19
12
22
32
42
52
62
72
82
12
22
32
42
52
62
72
82
V
V
14
24
34
44
54
64
74
84
14
24
34
44
54
64
74
84
G
G
11
21
31
41
51
61
71
81
11
21
31
41
51
61
71
81
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
Terminal name
Description
V (push-in power supply terminals)
Unit power supply terminals (24 VDC)
G (push-in power supply terminals)
11 to 81 (push-in I/O terminal common terminals)
12 to 82 (push-in I/O terminal NC terminals)
Relay contact terminals
14 to 84 (push-in I/O terminal NO terminals)
G70V-SOC16P-1
(PNP output/- common)
Note: A controller with a PNP transistor, + common output can be connected to the G70V-SOC16P-1.
Connector Pin Configuration
Top View
X Output relays
G2RV-1-S-G
Relay No.
1
2
3
4
5
6
7
8
−
+
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
−
+
mark
Connector pin No.
Connector
pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
10
20
9
19
V
V
G
G
12
14
11
22
24
21
32
34
31
42
44
41
52
54
51
62
64
61
72
74
71
82
84
81
12
14
11
22
24
21
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
Terminal name
V (push-in power supply terminals)
G (push-in power supply terminals)
Description
Unit power supply terminals (24 VDC)
11 to 81 (push-in I/O terminal common terminals)
12 to 82 (push-in I/O terminal NC terminals)
14 to 84 (push-in I/O terminal NO terminals)
8
Relay contact terminals
32
34
31
42
44
41
52
54
51
62
64
61
72
74
71
82
84
81
G70V
G70V-SOC16P-C4
(NPN output/+ common)
Note: A controller with an NPN transistor, common output can be connected to the G70V-SOC16P-C4.
Connector Pin Configuration
Top View
X Output relays
G2RV-1-S-G
Relay No.
1
2
3
4
5
6
7
8
−
+
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
−
+
Connector
pin No.
mark
Connector pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
10
20
9
19
12
22
32
42
52
62
72
82
12
22
32
42
52
62
72
82
V
V
14
24
34
44
54
64
74
84
14
24
34
44
54
64
74
84
G
G
11
21
31
41
51
61
71
81
11
21
31
41
51
61
71
81
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
Terminal name
Description
V (push-in power supply terminals)
Unit power supply terminals (24 VDC)
G (push-in power supply terminals)
11 to 81 (push-in I/O terminal common terminals)
12 to 82 (push-in I/O terminal NC terminals)
Relay contact terminals
14 to 84 (push-in I/O terminal NO terminals)
G70V-SOC16P-1-C4
(PNP output/- common)
Note: A controller with a PNP transistor, + common output can be connected to the G70V-SOC16P-1-C4.
Connector Pin Configuration
Top View
X Output relays
G2RV-1-S-G
Relay No.
1
2
3
4
5
6
7
8
−
+
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
−
+
mark
Connector pin No.
Connector
pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
10
20
9
19
12
22
32
42
52
62
72
82
12
22
32
42
52
62
72
82
V
V
14
24
34
44
54
64
74
84
14
24
34
44
54
64
74
84
G
G
11
21
31
41
51
61
71
81
11
21
31
41
51
61
71
81
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
Terminal name
V (push-in power supply terminals)
G (push-in power supply terminals)
Description
Unit power supply terminals (24 VDC)
11 to 81 (push-in I/O terminal common terminals)
12 to 82 (push-in I/O terminal NC terminals)
Relay contact terminals
14 to 84 (push-in I/O terminal NO terminals)
9
G70V
G70V-ZOM16P-C4-D
(NPN output/- common)
Note: A controller with an NPN transistor, common output can be connected to the G70V-ZOM16P-C4-D.
Connector Pin Configuration
Top View
X Output Relays*
G3RV-D03SL (Relays sold separately.)
Relay No.
1
2
3
4
5
6
7
8
−
+
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
−
+
Connector
pin No.
mark
Connector pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
10
20
9
19
V
V
G
G
12
22
32
42
52
62
72
82
12
22
32
42
52
62
72
82
14
24
34
44
54
64
74
84
14
24
34
44
54
64
74
84
11
21
31
41
51
61
71
81
11
21
31
41
51
61
71
81
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
Terminal name
Description
V (push-in power supply terminals)
Unit power supply terminals (24 VDC)
G (push-in power supply terminals)
11 to 81 (push-in I/O terminal SSR output terminal +)
12 to 82 (push-in I/O terminal Open terminal)
SSR contact terminals
14 to 84 (push-in I/O terminal SSR output terminal -)
* The G70V-ZOM16P-C4-D does not come with SSRs. Use Slim I/O SSRs (for DC: G3RV-D03SL).
G70V-ZOM16P-1-C4-D
(PNP output/- common)
Note: A controller with an PNP transistor, common output can be connected to the G70V-ZOM16P-1-C4-D.
Connector Pin Configuration
Top View
X Output Relays*
G3RV-D03SL (Relays sold separately.)
Relay No.
1
2
3
4
5
6
7
8
−
+
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
9
10
11
12
13
14
15
16
−
+
mark
Connector pin No.
Connector
pin No.
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
10
20
9
19
V
V
G
G
12
22
32
42
52
62
72
82
12
22
32
42
52
62
72
82
14
24
34
44
54
64
74
84
14
24
34
44
54
64
74
84
11
21
31
41
51
61
71
81
11
21
31
41
51
61
71
81
Note: Pin numbers are indicated for convenience. The ▲ mark can be used to determine orientation.
Terminal name
V (push-in power supply terminals)
G (push-in power supply terminals)
Description
Unit power supply terminals (24 VDC)
11 to 81 (push-in I/O terminal SSR output terminal +)
12 to 82 (push-in I/O terminal Open terminal)
SSR contact terminals
14 to 84 (push-in I/O terminal SSR output terminal -)
* The G70V-ZOM16P-1-C4-D does not come with SSRs. Use Slim I/O SSRs (for DC: G3RV-D03SL).
10
G70V
Dimensions
(Unit: mm)
Main unit
I/O Relay Terminals and I/O Terminal Sockets
For Inputs
G70V-SID16P
G70V-SID16P-1
G70V-ZID16P
G70V-ZID16P-1
G70V-SID16P-C16
G70V-SID16P-1-C16
G70V-ZID16P-C16
G70V-ZID16P-1-C16
143 max.
4.35
4.2-dia. hole (M4 screw)
4.35
Relay
90 max.
35.2
7.5
4.35
10.26
4.1
5
4.35
4.2-dia. hole
(M4 screw)
18.3
16.7
20.2
29.9
56 max.
Note: 1. Relays are not mounted to the G70V-ZID16P(-1)(-C16) I/O Terminal Sockets.
The dimensions are for when Relays are not mounted.
2. Specified mounting torque: 0.59 to 0.98 N·m.
For Outputs
G70V-SOC16P
G70V-SOC16P-1
G70V-ZOM16P
G70V-ZOM16P-1
G70V-SOC16P-C4
G70V-SOC16P-1-C4
G70V-ZOM16P-C4
G70V-ZOM16P-1-C4
G70V-ZOM16P-C4-D
G70V-ZOM16P-1-C4-D
143 max.
4.35
4.2-dia. hole (M4 screw)
4.35
Relay
90 max.
35.2
7.8
7.8
4.35
10.26
4.1
4.35
4.2-dia. hole
(M4 screw)
5
20.2
16.7
18.24
29.9
56 max.
Note: 1. Relays are not mounted to the G70V-ZOM16P(-1)(-C4)(-D) I/O Terminal Sockets.
The dimensions are for when Relays are not mounted.
2. Specified mounting torque: 0.59 to 0.98 N·m.
11
G70V
Options (Order Separately)
Mountable Relays
Slim I/O Relays
Models without latching lever
G2RV-1-S-G
G2RV-1-S-AP-G
5.2 max.
30.5 max.
Terminal Arrangement/
Internal Connection Diagram
(TOP VIEW)
33 max.
16.2
1.8
0.5
(Input circuit)
14 11 12
A1 A2
2.4
3.5
5.04
5.04
22
3
Slim I/O Relays
Models with latching lever (test switch)
G2RV-1-SI-G
5.2 max.
30.5 max.
Terminal Arrangement/
Internal Connection Diagram
(TOP VIEW)
(Input circuit)
36 max.
14 11 12
16.2
1.8
0.5
2.4
3.5
5.04
5.04
22
12
3
A1 A2
G70V
Slim I/O SSRs
G3RV-D03SL
G3RV-202S
G3RV-202SL
Terminal Arrangement/
Internal Connection Diagram
(TOP VIEW)
G3RV-D03SL (input circuit)
Input
30.5 max.
Load
33 max.
15.8
14
1.8
3.5
13
G3RV-202S(L) (input circuit)
2.4
22
Input
3
5.04
A1 A2
5.2 max.
Load
14
13
A1 A2
Parts for Rail Mounting
DIN Track
PFP-100N
PFP-50N
7.3±0.15
4.5
35±0.3
15
25
10
25
25
1,000 (500)*
End Plate
PFP-M
10
25
15 (5)*
27±0.15
1
*The dimensions given in parentheses () are for the PFP-50N.
10
6.2
50
Eight M4
pan head
screws
1.8
1
35.5 35.3
1.8
11.5
10
M4 spring washers
Spacer
PFP-S
1.3
4.8
16
12
5
34.8
44.3
16.5
13
G70V
Terminal Arrangement/Internal Connection
For Inputs
G70V-SID16P
G70V-SID16P-1
• Supply a power supply that meets the voltage specifications
for both the Relays and I/O Relay Terminal to the V and G
terminals.
Make sure that the polarity is correct.
The V terminals are positive and the G terminals are
negative.
• Supply the rated voltage (24 VDC) of the Controller’s input
circuit to the power supply input terminals (V and G). Use a
power supply with low noise.
Power supply terminal block
Communications
connector
Input Relays
(G2RV-1-S-AP-G)
Operation indicator
(yellow)
V
V
G G
V
DIN Track mounting hooks
I/O Terminal
Blocks
V
V
V
V
V
V
V
V
G G G G G G G G
V
V
V
V
V
V
V
24 VDC
G G G G G G G G
24 VDC
For Outputs
G70V-SOC16P
G70V-SOC16P-1
Power supply terminal block
Operation
indicator (yellow)
Communications
connector
Output Relays
(G2RV-1-S-G)
• Supply a power supply that meets the voltage specifications
for both the Relays and I/O Relay Terminal to the V and G
terminals.
Make sure that the polarity is correct.
The V terminals are positive and the G terminals are
negative.
• The terminals (11 to 81, 12 to 82, and 14 to 84) are contact
outputs. Supply a suitable power supply for the loads.
• The power supply input terminals (V and G) supply power to
both drive the Relays and to operate the Controller’s output
transistors.
Align the voltage specifications of the Controller and the I/O
Relay Terminal.
DIN Track mounting hooks I/O Terminal Blocks
L0 L1 L2 L3 L4 L5 L6 L7
L8 L9 L10 L11 L12 L13 L14 L15
12 22 32 42 52 62 72 82
12 22 32 42 52 62 72 82
V
14 24 34 44 54 64 74 84
14 24 34 44 54 64 74 84
G G
11 21 31 41 51 61 71 81
11 21 31 41 51 61 71 81
AC (DC power supply is also possible.)
V
24 VDC
14
G70V
For Inputs
G70V-SID16P-C16
G70V-SID16P-1-C16
• Supply a power supply that meets the voltage specifications
for both the Relays and I/O Relay Terminal to the V and G
terminals.
Make sure that the polarity is correct.
The V terminals are positive and the G terminals are
negative.
• Supply the rated voltage (24 VDC) of the Controller’s input
circuit to the power supply input terminals (V and G). Use a
power supply with low noise.
Power supply terminal block
Communications
connector
Input Relays
(G2RV-1-S-AP-G)
Operation indicator
(yellow)
DIN Track mounting hooks
I/O Terminal
Blocks
G70V-SID16P-C16
V
V
V
G G
V
V
V
V
V
V
V
G G G G G G G G
V
V
V
V
V
G70V-SID16P-1-C16
V
V
V
24 VDC
G G G G G G G G
V
V
G G
V
V
V
V
V
V
V
V
G G G G G G G G
V
V
V
V
V
V
V
V
24 VDC
G G G G G G G G
24 VDC
24 VDC
For Outputs
G70V-SOC16P-C4
G70V-SOC16P-1-C4
Power supply terminal block
Operation
indicator (yellow)
Communications
connector
Output Relays
(G2RV-1-S-G)
• Supply a power supply that meets the voltage specifications
for both the Relays and I/O Relay Terminal to the V and G
terminals.
Make sure that the polarity is correct.
The V terminals are positive and the G terminals are
negative.
• The terminals (11 to 81, 12 to 82, and 14 to 84) are contact
outputs. Supply a suitable power supply for the loads.
• The power supply input terminals (V and G) supply power to
both drive the Relays and to operate the Controller’s output
transistors.
Align the voltage specifications of the Controller and the I/O
Relay Terminal.
DIN Track mounting hooks I/O Terminal Blocks
L0 L1 L2 L3 L4 L5 L6 L7
L8 L9 L10 L11 L12 L13 L14 L15
12 22 32 42 52 62 72 82
12 22 32 42 52 62 72 82
V
14 24 34 44 54 64 74 84
14 24 34 44 54 64 74 84
G G
11 21 31 41 51 61 71 81
11 21 31 41 51 61 71 81
AC (DC power supply is also possible.)
V
24 VDC
15
G70V
For Outputs
G70V-ZOM16P-C4-D
G70V-ZOM16P-1-C4-D
Power supply terminal block
Operation
indicator (yellow)
Communications
connector
Output Relays*
G3RV-D03SL
(Relays sold separately.)
• Supply a power supply that meets the voltage specifications
for both the Relays and I/O Relay Terminal to the V and G
terminals.
Make sure that the polarity is correct.
The V terminals are positive and the G terminals are
negative.
• The terminals (11 to 81 and 14 to 84) are contact outputs.
Supply a suitable power supply for the loads. Make sure that
polarity of the output terminal is correct.
• The power supply input terminals (V and G) supply power to
both drive the Relays and to operate the Controller’s output
transistors.
Align the voltage specifications of the Controller and the I/O
Relay Terminal.
DIN Track mounting hooks I/O Terminal Blocks
12 22 32 42 52 62 72 82
12 22 32 42 52 62 72 82
V
14 24 34 44 54 64 74 84
14 24 34 44 54 64 74 84
G G
11 21 31 41 51 61 71 81
11 21 31 41 51 61 71 81
L0 L1 L2 L3 L4 L5 L6 L7
L8 L9 L10 L11 L12 L13 L14 L15
V
24 VDC
16
DC
* The G70V-ZOM16P(-1)-C4-D does not come with SSRs.
Use Slim I/O SSRs (for DC: G3RV-D03SL).
G70V
Safety Precautions
Be sure to read The Safety Precautions for All I/O Relay Terminals in the website at the following URL:
http://www.ia.omron.com/product/cautions/46/243/index.html.
Warning Indications
Precautions for
Safe Use
Supplementary comments on what to do
or avoid doing, to use the product safely.
Precautions for
Correct Use
Supplementary comments on what to do
or avoid doing, to prevent failure to
operate, malfunction, or undesirable
effects on product performance.
Precautions for Safe Use
Transportation
• Do not transport the I/O Relay Terminal under the following
locations. Doing so may occasionally result in damage,
malfunction, or deterioration of performance characteristics.
• Locations subject to water or oil
• Locations subject to high temperature or high humidity
• Locations subject to condensation due to rapid changes in
temperature
Operating and Storage Environments
• Do not use or store the I/O Relay Terminal in the following
locations. Doing so may result in damage, malfunction, or
deterioration of performance characteristics.
• Locations subject to rainwater or water splashes
• Locations subject to exposure to water, oil, or chemicals
• Locations subject to high temperature or high humidity
• Locations subject to ambient storage temperatures outside the
range −40 to 65°C
• Locations subject to ambient operating temperatures outside the
range −40 to 55°C
• Locations subject to relative humidity outside the range 35% to
85% or locations in which condensation may occur due to rapid
changes in temperature
• Locations subject to corrosive gases or inflammable gases
• Locations subject to dust, salts, or iron, or locations where there
is salt damage
• Locations subject to direct sunlight
• Locations subject to shock or vibration
Installation and Mounting
• Mount the I/O Relay Terminal in the specified direction. Otherwise
excessive heat generated by the I/O Relay Terminal may
occasionally cause burning.
• Mount the I/O Relay Terminal firmly to a DIN Track. Otherwise, the
I/O Relay Terminal may fall off.
• Do not handle the I/O Relay Terminal with oily or dusty (especially
iron dust) hands.
• Make sure that there is no excessive ambient temperature rise due
to the heat generation of the I/O Relay Terminal. If the I/O Relay
Terminal is mounted inside a panel, install a fan so that the interior
of the panel is fully ventilated.
Push-In Plus Terminal Blocks
• Do not wire anything to the release holes.
• Do not tilt or twist a flat-blade screwdriver while it is inserted into a
release hole on the terminal block. The terminal block may be
damaged.
• Insert a flat-blade screwdriver into the release holes at an angle.
The terminal block may be damaged if you insert the screwdriver
straight in.
• Do not allow the flat-blade screwdriver to fall out while it is inserted
into a release hole.
• Do not bend a wire past its natural bending radius or pull on it with
excessive force. Doing so may cause the wire disconnection.
• Do not insert more than one wire into each terminal insertion hole.
• To prevent wire materials from smoking or igniting, confirm wire
ratings and use the wiring materials given in the following table.
Stripping length
(Ferrules not used)
Recommended wire gauge
0.25 to 1.5mm2/AWG24 to 16
8 mm
• Refer to the following table for wire sizes for external I/O devices
according to the current flow.
AWG24 to AWG20
Maximum current flow: 6 A
AWG18 to AWG16
Maximum current flow: 10 A
Application
• Select a load within the rated values. Not doing so may result in
malfunction, failure, or burning.
• The I/O Relay Terminal may occasionally rupture if short-circuit
current flows. As protection against accidents due to shortcircuiting, be sure to install protective devices, such as fuses and
no-fuse breakers, on the power supply side.
• Use a power supply within the rated frequencies. Otherwise,
malfunction, failure, or burning may occasionally occur.
• Minor electric shock may occasionally occur. Always turn OFF the
power supply before performing wiring.
Precautions for Correct Use
• Do not drop the I/O Relay Terminal or subject it to abnormal
vibration or shock during transportation or mounting. Doing so may
result in deterioration of performance, malfunction, or failure.
• Do not transport an I/O Relay Terminal when it is not packaged.
Damage or failure may occur.
• Use a power supply with low noise.
Push-In Plus Terminal Blocks
1. Connecting Wires to the Push-In Plus Terminal Block
Part Names of the Terminal Block
Release hole
Terminal (Insertion) hole
Installation and Wiring
• Use wires that are suited to the load current and voltage.
Otherwise, excessive heat generated by the wires may cause
burning or may cause the wire covering to melt, possibly leading to
electric shock.
• Do not use wires with a damaged outer covering. Otherwise, it may
result in electric shock or ground leakage.
• Do not wire any wiring in the same duct or conduit as power or
high-tension lines. Otherwise, inductive noise may damage the I/O
Relay Terminal or cause it to malfunction.
• Do not apply a voltage or current that exceeds the rating to any
terminal. Doing so may result in failure or burning.
Connecting Wires with Ferrules and Solid Wires
Insert the solid wire or ferrule straight into the terminal block until the
end strikes the terminal block.
Release hole
Terminal (Insertion) hole
Ferrules
and solid wires
• If a wire is difficult to connect because it is too thin, use a flat-blade
screwdriver in the same way as when connecting stranded wire.
17
G70V
Connecting Stranded Wires
Use the following procedure to connect the wires to the terminal block.
1. Hold a flat-blade screwdriver at an angle and insert it into the
release hole.
The angle should be between 10° and 15°. If the flat-blade
screwdriver is inserted correctly, you will feel the spring in the
release hole.
2. With the flat-blade screwdriver still inserted into the release hole,
insert the wire into the terminal hole until it strikes the terminal
block.
3. Remove the flat-blade screwdriver from the release hole.
Flat-blade screwdriver
3
1
3
3. Recommended Ferrules and Crimp Tools
Recommended ferrules
Applicable
wire
Stripping
Ferrule
length
Conductor
[mm]
length
(Ferrules
(mm2) (AWG)
(mm)
used)
0.25
10 to 15°
0.5
Stranded Wires
Checking Connections
• After the insertion, pull gently on the wire to make sure that it will
not come off and the wire is securely fastened to the terminal block.
• If you use a ferrule with a conductor length of 10 mm, part of the
conductor may be visible after the ferrule is inserted into the
terminal block, but the product insulation distance will still be
satisfied.
2. Removing Wires from the Push-In Plus Terminal Block
Use the following procedure to remove wires from the terminal block.
The same method is used to remove stranded wires, solid wires, and
ferrules.
1. Hold a flat-blade screwdriver at an angle and insert it into the
release hole.
2. With the flat-blade screwdriver still inserted into the release hole,
remove the wire from the terminal insertion hole.
3. Remove the flat-blade screwdriver from the release hole.
1
8
10 AI0,25-8
10
12 AI0,25-10
Weidmuller
product
H0.25/12
Wago
product
216-301
8
10 AI0,34-8
10
12 AI0,34-10
--H0.34/12
--216-302
22
---
---
8
10 AI0,5-8
H0.5/14
216-201
10
12 AI0,5-10
H0.5/16
216-241
8
10 AI0,75-8
H0.75/14
216-202
20
2
2
Phoenix
Contact
product
24
0.34
1
Recommended ferrules
0.75
18
12 AI0,75-10
H0.75/16
216-242
8
10 AI1-8
H1.0/14
216-203
10
12 AI1-10
H1.0/16
216-243
8
10 AI1,5-8
H1.5/14
216-204
10
12 AI1,5-10
H1.5/16
216-244
10
1/1.25
18/17
1.25/1.5 17/16
Recommended crimp tool
CRIMPFOX6
CRIMPFOX6T-F PZ6 roto
CRIMPFOX10S
Variocrimp4
Note: 1. Make sure that the outer diameter of the wire coating is
smaller than the inner diameter of the insulation sleeve of
the recommended ferrule.
2. Make sure that the ferrule processing dimensions conform
to the following figures.
8 to 10 mm
Flat-blade screwdriver
3
3
1
10 to 15°
2
2
Wire
2.6 mm max.
1.9 mm max.
Recommended Flat-blade Screwdriver
Use a flat-blade screwdriver to connect and remove wires.
Use the following flat-blade screwdriver.
The following table shows manufacturers and models as of 2015/Dec.
Side
Front
2.5 mm dia.
0.4 mm
2.5 mm
Model
Manufacturer
ESD 0,40×2,5
Wera
SZS 0,4×2,5
SZF 0-0,4×2,5 *
Phoenix Contact
0.4×2.5×75 302
Wiha
AEF.2,5×75
Facom
210-719
Wago
SDI 0.4×2.5×75
Weidmuller
* OMRON's exclusive purchase model XW4Z-00B is available to
order as SZF 0-0,4 × 2,5 (manufactured by Phoenix Contact).
18
G70V
Connecting Cables
Refer to the datasheet for the XW2Z-R Cables for I/O Relay Terminals (Cat. No. G126).
Type
Name
Cables with Loose Wires
and Crimp Terminals
I/O Classification
Appearance
Cable length L (mm)
B side
A side
Device end
I/O Relay Terminal
16 I/O points
XW2Z-RYC
Various devices
L
300
Cables with Loose Wires
Models
1,000
XW2Z-RY100C
1,500
XW2Z-RY150C
2,000
XW2Z-RY200C
3,000
XW2Z-RY300C
5,000
XW2Z-RY500C
2,000
XW2Z-RA200C
5,000
XW2Z-RA500C
1,000
XW2Z-R100C
1,500
XW2Z-R150C
2,000
XW2Z-R200C
3,000
XW2Z-R300C
16 I/O points
XW2Z-RAC
L
300
Fujitsu connectors (24 pins)
Cables with Connectors
(1:1)
16 I/O points
XW2Z-RC
L
5,000
(A)
32 input points
Cables with Connectors
(1:2)
Fujitsu connectors (40 pins)
(120)
XW2Z-RIC-
XW2Z-ROC-
32 output points
(B)
Straight length (without bends)
(A)
(B)
Fujitsu connectors (56 pins)
Cables with Connectors
(1:3)
48 I/O points
(120)
XW2Z-R500C
(A) 1,000
(B) 750
XW2Z-RI100C-75
(A) 1,500
(B) 1,250
XW2Z-RI150C-125
(A) 2,000
(B) 1,750
XW2Z-RI200C-175
(A) 3,000
(B) 2,750
XW2Z-RI300C-275
(A) 5,000
(B) 4,750
XW2Z-RI500C-475
(A) 1,000
(B) 750
XW2Z-RO100C-75
(A) 1,500
(B) 1,250
XW2Z-RO150C-125
(A) 2,000
(B) 1,750
XW2Z-RO200C-175
(A) 3,000
(B) 2,750
XW2Z-RO300C-275
(A) 5,000
(B) 4,750
XW2Z-RO500C-475
(A)
1,500
(B)
1,250
(C)
1,000
XW2Z-R150C-125-100
(A)
2,000
(B)
1,750
(C)
1,500
XW2Z-R200C-175-150
(A)
3,000
(B)
2,750
(C)
2,500
XW2Z-R300C-275-250
(270)
XW2Z-RC--
(C)
Straight length (without bends)
Cables with Connectors
(1:1)
MIL connectors (20 pins)
16 I/O points
XW2Z-RIC
XW2Z-ROC
250
XW2Z-RI25C
500
XW2Z-RI50C
250
XW2Z-RO25C
500
XW2Z-RO50C
L
19
G70V
Type
Name
I/O Classification
Appearance
B side
A side
Device end
Cables with Connectors
(1:2)
MIL connectors (40 pins)
I/O Relay Terminal
32 I/O points
XW2Z-RO--D1,
XW2Z-RI--D1,
XW2Z-RI--D2,
XW2Z-RM--D1 *1,
XW2Z-RM--D2 *1
Cable length L (mm)
(A)
(120)
(B)
Straight length (without bends)
16 inputs and
16 outputs
(32 I/O points)
(A)
32 input points
Mitsubishi Electric PLCs with
32-point connectors (1:2) *2
Mitsubishi Electric PLC
Connecting Cables
(120)
XW2Z-RIC--MN
XW2Z-ROC--MN
32 output points
(B) 250
XW2Z-RO50-25-D1
(A) 750
(B) 500
XW2Z-RO75-50-D1
(A) 1,000
(B) 750
XW2Z-RO100-75-D1
(A) 1,500
(B) 1,250
XW2Z-RO150-125-D1
(A) 2,000
(B) 1,750
XW2Z-RO200-175-D1
(A) 3,000
(B) 2,750
XW2Z-RO300-275-D1
(A) 5,000
(B) 4,750
XW2Z-RO500-475-D1
(A) 500
(B) 250
XW2Z-RI50-25-D1
(A) 750
(B) 500
XW2Z-RI75-50-D1
(A) 1,000
(B) 750
XW2Z-RI100-75-D1
(A) 1,500
(B) 1,250
XW2Z-RI150-125-D1
(A) 2,000
(B) 1,750
XW2Z-RI200-175-D1
(A) 3,000
(B) 2,750
XW2Z-RI300-275-D1
(A) 5,000
(B) 4,750
XW2Z-RI500-475-D1
(A) 500
(B) 250
XW2Z-RI50-25-D2
(A) 750
(B) 500
XW2Z-RI75-50-D2
(A) 500
(B) 250
XW2Z-RM50-25-D1
(A) 750
(B) 500
XW2Z-RM75-50-D1
(A) 500
(B) 250
XW2Z-RM50-25-D2
(A) 750
(B) 500
XW2Z-RM75-50-D2
(A) 1,000
(B) 750
XW2Z-RI100C-75-MN
(A) 1,500
(B) 1,250
XW2Z-RI150C-125-MN
(A) 2,000
(B) 1,750
XW2Z-RI200C-175-MN
(A) 3,000
(B) 2,750
XW2Z-RI300C-275-MN
(A) 1,000
(B) 750
XW2Z-RO100C-75-MN
(A) 1,500
(B) 1,250
XW2Z-RO150C-125-MN
(A) 2,000
(B) 1,750
XW2Z-RO200C-175-MN
(B)
Straight length (without bends)
(A) 3,000
(A)
32 input points
Schneider Electric PLCs with
32-point connectors (1:2)
Applicable models:
For inputs:
140 DDI 353 00
For outputs:
140 DDO 353 00
(120)
32 output points
(B)
Straight length (without bends)
Schneider Electric PLC
Connecting Cables
XW2Z-R@C-SCH-@
Schneider Electric PLCs with
16-point connectors (1:1)
Applicable models:
For inputs:
BMX DDI 1602
For outputs:
BMX DDO 1602
Models
(A) 500
16 input points
(B) 2,750
XW2Z-RO300C-275-MN
500
XW2Z-R050C-SCH-A
1,000
XW2Z-R100C-SCH-A
2,000
XW2Z-R200C-SCH-A
3,000
XW2Z-R300C-SCH-A
5,000
XW2Z-R500C-SCH-A
500
XW2Z-R050C-SCH-B
1,000
XW2Z-R100C-SCH-B
2,000
XW2Z-R200C-SCH-B
3,000
XW2Z-R300C-SCH-B
5,000
XW2Z-R500C-SCH-B
500
XW2Z-R050C-SCH-C
1,000
XW2Z-R100C-SCH-C
2,000
XW2Z-R200C-SCH-C
3,000
XW2Z-R300C-SCH-C
5,000
XW2Z-R500C-SCH-C
500
XW2Z-R050C-SCH-D
1,000
XW2Z-R100C-SCH-D
2,000
XW2Z-R200C-SCH-D
3,000
XW2Z-R300C-SCH-D
5,000
XW2Z-R500C-SCH-D
L
16 output points
Note: Contact for a cable length other than the above.
Cables that can be connected to the QX81, QX81-S2, and QY81P have not been prepared.
*1. These cables are used to connect to slave products for DeviceNet and other networks.
*2. For details on models that can be used, refer to List of Combinations with the Mitsubishi PLC MELSEC-L Series, MELSEC-Q Series, and
MELSEC iQ-R Series on page 26.
20
G70V
Type
Name
I/O Classification
Appearance
Siemens PLCs with
32-point connectors (1:2)
500
XW2Z-R050C-SIM-A
1,000
XW2Z-R100C-SIM-A
I/O Relay Terminal
2,000
XW2Z-R200C-SIM-A
3,000
XW2Z-R300C-SIM-A
5,000
XW2Z-R500C-SIM-A
500
XW2Z-R050C-SIM-B
1,000
XW2Z-R100C-SIM-B
2,000
XW2Z-R200C-SIM-B
3,000
XW2Z-R300C-SIM-B
(A)
Applicable models:
For inputs:
6ES7 321-1BL00-0AA0
For outputs:
6ES7 322-1BL00-0AA0
Siemens PLCs with
16-point connectors (1:1)
Applicable models:
For inputs:
6ES7 321-1BH02-0AA0
Siemens PLCs with
32-point connectors (1:2)
Applicable models:
For inputs:
6ES7 421-1BL-0AA0
For outputs:
6ES7 422-1BL-0AA0
Device end
(120)
32 output points
Siemens PLC Connecting
Cables
(B)
Straight length (without bends)
16 input points
XW2Z-R@C-SIM-@
L
(A)
32 input points
(120)
32 output points
Models
B side
A side
32 input points
Cable length L (mm)
(B)
Straight length (without bends)
5,000
XW2Z-R500C-SIM-B
500
XW2Z-R050C-SIM-C
1,000
XW2Z-R100C-SIM-C
2,000
XW2Z-R200C-SIM-C
3,000
XW2Z-R300C-SIM-C
5,000
XW2Z-R500C-SIM-C
500
XW2Z-R050C-SIM-D
1,000
XW2Z-R100C-SIM-D
2,000
XW2Z-R200C-SIM-D
3,000
XW2Z-R300C-SIM-D
5,000
XW2Z-R500C-SIM-D
500
XW2Z-R050C-SIM-E
1,000
XW2Z-R100C-SIM-E
2,000
XW2Z-R200C-SIM-E
3,000
XW2Z-R300C-SIM-E
5,000
XW2Z-R500C-SIM-E
Note: 1. Refer to Combinations of Connections starting on the next page.
2. For connector pin diagrams and cable colors, refer to the wiring diagrams starting on page 4 of XW2Z-R Cables for I/O Relay Terminals
(Cat. No. G126).
21
G70V
Combinations of Connections
Refer to the next page for details on the combinations of cables and connection devices [OMRON PLC I/O Units NX Series, CJ Series, CS Series],
[Mitsubishi PLC I/O Units MELSEC-L Series, MELSEC-Q Series, MELSEC iQ-R Series].
For combinations with other products, refer to I/O Relay Terminals and Connected Devices (Cat. No. J217) or to the datasheets for related
products.
Connection Patterns
Pattern
Configuration
Connecting Cable
I/O Relay Terminals
A
I/O Relay Terminals
I/O Relay Terminals
B
Connecting Cable
I/O Relay Terminals
I/O Relay Terminals
D
Connecting Cable
E
I/O Relay Terminals
I/O Relay Terminals
Connecting Cable
Connecting Cable
F
I/O Relay Terminals
22
G70V
List of Combinations with the OMRON PLC NX Series
NX I/O Units
I/O
capacity
Model
External
connectors
Polarity
XW2Z-R Cables
Conne
ction
Model *1
pattern Specifications
G70V I/O Relay Terminals
Quantity
required
Model
Quantity
required
G70V-SID16P(-1)(-C16)
1
G70V-SID16P(-1)(-C16)
2
G70V-SID16P(-1)(-C16)
2
Specifications
Input Units
16 inputs NX-ID5142-5
1 MIL connector
NPN or PNP
NX-ID6142-5
1 MIL connector
NPN or PNP
NX-ID6142-6
1 Fujitsu connector
NPN or PNP
32 inputs
F
1:1
A
1:2
F
1:1
XW2Z-RO@C
1
XW2Z-RO@-@-D1
1
XW2Z-RI@C-@
1
XW2Z-RO@C
1
NPN outputs
G70V-SOC16P(-C4)
1
XW2Z-RO@C
1
PNP outputs
G70V-SOC16P-1(-C4)
1
XW2Z-RO@-@-D1
1
NPN outputs
G70V-SOC16P(-C4)
2
---
---
PNP outputs
---
---
XW2Z-RO@C-@
1
NPN outputs
G70V-SOC16P(-C4)
2
Inputs *2
G70V-SID16P(-1)(-C16)
1
XW2Z-R@C
2
NPN outputs
G70V-SOC16P(-C4)
1
XW2Z-RO@C
1
Inputs *2
G70V-SID16P(-1)(-C16)
1
XW2Z-RO@C
1
NPN outputs
G70V-SOC16P(-C4)
1
XW2Z-RO@C
1
Inputs *2
G70V-SID16P(-1)(-C16)
1
XW2Z-RI@C
1
PNP outputs
G70V-SOC16P-1(-C4)
1
Inputs *2
Output Units
16
outputs
32
outputs
NX-OD5121-5 1 MIL connector
NPN
NX-OD5256-5 1 MIL connector
PNP
NX-OD6121-5 1 MIL connector
NPN
NX-OD6256-5 1 MIL connector
PNP
NX-OD6121-6 1 Fujitsu connector
NPN
A
1:2
Mixed I/O Units
16 inputs
and 16
outputs
2 Fujitsu connectors
NX-MD6121-6 (1 for 16 inputs and
1 for 16 outputs)
Outputs:
NPN
Inputs:
NPN or PNP
2 MIL connectors
NX-MD6121-5 (1 for 16 inputs and
1 for 16 outputs)
Outputs:
NPN
Inputs:
NPN or PNP
2 MIL connectors
NX-MD6256-5 (1 for 16 inputs and
1 for 16 outputs)
Outputs:
PNP
Inputs:
NPN or PNP
E
1:1
*1. The box @ is replaced by the cable length.
*2. Either NPN inputs or PNP inputs can be used.
23
G70V
List of Combinations with the OMRON PLC CJ Series
CJ1W I/O Units
I/O
capacity
Model
External
connectors *1
Polarity
Conne
ction
pattern
XW2Z-R Cables
Specifications
Model *2
G70V I/O Relay Terminals
Quantity
required
Model
Quantity
required
G70V-SID16P(-1)(-C16)
2
G70V-SID16P(-1)(-C16)
4
NPN outputs
G70V-SOC16P(-C4)
2
Specifications
DC Input Units
1 Fujitsu connector
NPN
32 inputs CJ1W-ID232
CJ1W-ID231
1 MIL connector
NPN
XW2Z-RI@C-@
1
XW2Z-RO@-@-D1
CJ1W-ID233
1 MIL connector
NPN
1
XW2Z-RO@-@-D1
1
CJ1W-ID261
2 Fujitsu connectors
(2, 32-point connectors)
NPN
XW2Z-RI@C-@
2
CJ1W-ID262
2 MIL connectors
(2, 32-point connectors)
NPN
XW2Z-RO@-@-D1
2
CJ1W-OD231
1 Fujitsu connector
Sinking
(NPN)
XW2Z-RO@C-@
1
CJ1W-OD233
1 MIL connector
Sinking
(NPN)
XW2Z-RO@-@-D1
1
CJ1W-OD232
1 MIL connector
Sourcing
(PNP)
XW2Z-RO@-@-D1
1
PNP outputs
G70V-SOC16P-1(-C4)
2
CJ1W-OD234
1 MIL connector
Sinking
(NPN)
XW2Z-RO@-@-D1
1
NPN outputs
G70V-SOC16P(-C4)
2
CJ1W-OD261
2 Fujitsu connectors
(2, 32-point connectors)
Sinking
(NPN)
XW2Z-RO@C-@
2
NPN outputs
G70V-SOC16P(-C4)
4
CJ1W-OD262
2 MIL connectors
(2, 32-point connectors)
Sourcing
(PNP)
XW2Z-RO@-@-D1
2
PNP outputs
G70V-SOC16P-1(-C4)
4
CJ1W-OD263
2 MIL connectors
(2, 32-point connectors)
Sinking
(NPN)
XW2Z-RO@-@-D1
2
NPN outputs
G70V-SOC16P(-C4)
4
Inputs *3
G70V-SID16P(-1)(-C16)
1
XW2Z-R@C
2
NPN outputs
G70V-SOC16P(-C4)
1
64 inputs
A
1:2
Inputs *3
B
Transistor Output Units
32
outputs
64
outputs
A
1:2
B
DC Input/Transistor Output Units
16 inputs
and 16
outputs
32 inputs
and 32
outputs
CJ1W-MD231
2 Fujitsu connectors
(1 for 16 inputs and
1 for 16 outputs)
Sinking
(NPN)
CJ1W-MD233
2 MIL connectors
(1 for 16 inputs and
1 for 16 outputs)
Sinking
(NPN)
CJ1W-MD232
2 MIL connectors
(1 for 16 inputs and
1 for 16 outputs)
Sourcing
(PNP)
CJ1W-MD261
2 Fujitsu connectors
(1 for 32 inputs and
1 for 32 outputs)
Sinking
(NPN)
2 MIL connectors
(1 for 32 inputs and
1 for 32 outputs)
Sinking
(NPN)
CJ1W-MD263
E
B
1:1
1:2
*1. For details on the types of connectors, refer to pages 19 and 20.
*2. The box @ is replaced by the cable length.
*3. Either NPN inputs or PNP inputs can be used.
24
XW2Z-RO@C
1
Inputs *3
G70V-SID16P(-1)(-C16)
1
XW2Z-RO@C
1
NPN outputs
G70V-SOC16P(-C4)
1
XW2Z-RO@C
1
Inputs *3
G70V-SID16P(-1)(-C16)
1
XW2Z-RI@C
1
PNP outputs
G70V-SOC16P-1(-C4)
1
XW2Z-RI@C-@
1
Inputs *3
G70V-SID16P(-1)(-C16)
2
XW2Z-RO@C-@
1
NPN outputs
G70V-SOC16P(-C4)
2
XW2Z-RO@-@-D1
1
Inputs *3
G70V-SID16P(-1)(-C16)
2
XW2Z-RO@-@-D1
1
NPN outputs
G70V-SOC16P(-C4)
2
G70V
List of Combinations with the OMRON PLC CS Series
CJ1W I/O Units
I/O
capacity
Model
External
connectors *1
Polarity
Conne
ction
pattern
NPN
A
XW2Z-R Cables
Specifications
G70V I/O Relay Terminals
Model *2
Quantity
required
Model
Quantity
required
XW2Z-RI@C-@
1
G70V-SID16P(-1)(-C16)
2
XW2Z-RI@C-@
2
G70V-SID16P(-1)(-C16)
4
XW2Z-R@C-@-@
2
G70V-SID16P(-1)(-C16)
6
XW2Z-RO@C-@
1
NPN outputs
G70V-SOC16P(-C4)
2
XW2Z-RO@C-@
1
PNP outputs
G70V-SOC16P-1(-C4)
2
XW2Z-RO@C-@
2
NPN outputs
G70V-SOC16P(-C4)
4
XW2Z-RO@C-@
2
PNP outputs
G70V-SOC16P-1(-C4)
4
XW2Z-R@C-@-@
2
NPN outputs
G70V-SOC16P(-C4)
6
XW2Z-RI@C-@
1
Inputs *3
G70V-SID16P(-1)(-C16)
2
XW2Z-RO@C-@
1
NPN outputs
G70V-SOC16P(-C4)
2
XW2Z-RI@C-@
1
Inputs *3
G70V-SID16P(-1)(-C16)
2
XW2Z-RO@C-@
1
PNP outputs
G70V-SOC16P-1(-C4)
2
Inputs *3
G70V-SID16P(-1)(-C16)
3
NPN outputs
G70V-SOC16P(-C4)
3
Inputs *3
G70V-SID16P(-1)(-C16)
3
Specifications
DC Input Units
32 inputs CS1W-ID231
1 Fujitsu connector
64 inputs CS1W-ID261
2 Fujitsu connectors
(2, 32-point connectors)
NPN
B
96 inputs CS1W-ID291
2 Fujitsu connectors
(2, 48-point connectors)
NPN
D
1:2
1:3
Inputs *3
Transistor Output Units
32
outputs
64
outputs
96
outputs
CS1W-OD231 1 Fujitsu connector
CS1W-OD232 1 Fujitsu connector
Sinking
(NPN)
Sourcing
(PNP)
2 Fujitsu connectors
(2, 32-point connectors)
Sinking
(NPN)
CS1W-OD262
2 Fujitsu connectors
(2, 32-point connectors)
Sourcing
(PNP)
CS1W-OD291
2 Fujitsu connectors
(2, 48-point connectors)
Sinking
(NPN)
CS1W-OD261
A
1:2
B
D
1:3
DC Input/Transistor Output Units
32 inputs
and 32
outputs
48 inputs
and 48
outputs
CS1WMD261
2 Fujitsu connectors
(1 for 32 inputs and
1 for 32 outputs)
CS1WMD262
2 Fujitsu connectors
(1 for 32 inputs and
1 for 32 outputs)
CS1WMD291
2 Fujitsu connectors
(1 for 48 inputs and
1 for 48 outputs)
CS1WMD292
2 Fujitsu connectors
(1 for 48 inputs and
1 for 48 outputs)
Sinking
(NPN)
B
1:2
Sourcing
(PNP)
Sinking
(NPN)
D
1:3
Sourcing
(PNP)
XW2Z-R@C-@-@
2
XW2Z-R@C-@-@
1
---
*1. For details on the types of connectors, refer to pages 19 and 20.
*2. The box @ is replaced by the cable length.
*3. Either NPN inputs or PNP inputs can be used.
Refer to the manuals for the connected PLC for the connections to I/O Units for OMRON PLCs.
Series
Model
Man. No.
Manual Name
CS1
CS1G-CPUH, CS1H-CPUH
W339
Programmable Controllers Operation Manual
CJ1
CJ1H-CPUH-R, CJ1G/H-CPUH, CJ1GCPUP, CJ1M-CPU, CJ1G-CPU
W393
CJ Series
Programmable Controllers Operation Manual
CJ2
CJ2H-CPU6-EIP, CJ2H-CPU6, CJ2M-CPU
W472
CJ-series CJ2 CPU Unit Hardware User’s Manual
NJ
NJ501-
W500
NJ-series CPU Unit Hardware User's Manual
NX
NX-ID, NX-IA,
NX-OD, NX-OC, NX-MD
W521
NX-series Digital I/O Units User’s Manual
25
G70V
List of Combinations with the Mitsubishi PLC MELSEC-L Series, MELSEC-Q Series,
and MELSEC iQ-R Series
PLC I/O Unit
I/O
capacity
Model
External
connectors
Conne
ction
pattern
XW2Z-R Cables
G70V I/O Relay Terminals
Quantity
required
Specifications
XW2Z-RI@@@
-@@MN
1
Inputs *2
G70V-SID16P(-1)(-C16)
2
XW2Z-RI@@@
-@@MN
2
Inputs *2
G70V-SID16P(-1)(-C16)
4
XW2Z-RO@@@
-@@MN
1
NPN outputs
G70V-SOC16P(-C4)
2
XW2Z-RO@@@
-@@MN
1
PNP outputs
G70V-SOC16P-1(-C4)
2
XW2Z-RO@@@
-@@MN
2
NPN outputs
G70V-SOC16P(-C4)
4
PNP
XW2Z-RO@@@
-@@MN
2
PNP outputs
G70V-SOC16P-1(-C4)
4
NPN or
PNP
XW2Z-RI@@@
-@@MN
1
Inputs *2
G70V-SID16P(-1)(-C16)
2
NPN
XW2Z-RO@@@
-@@MN
1
NPN outputs
G70V-SOC16P(-C4)
2
NPN or
PNP
XW2Z-RI@@@
-@@MN
1
Inputs *2
G70V-SID16P(-1)(-C16)
2
NPN
XW2Z-RO@@@
-@@MN
1
NPN outputs
G70V-SOC16P(-C4)
2
NPN or
PNP
XW2Z-RI@@@
-@@MN
1
Inputs *2
G70V-SID16P(-1)(-C16)
2
NPN
XW2Z-RO@@@
-@@MN
1
NPN outputs
G70V-SOC16P(-C4)
2
NPN or
PNP
XW2Z-RI@@@
-@@MN
1
Inputs *2
G70V-SID16P(-1)(-C16)
2
NPN
XW2Z-RO@@@
-@@MN
1
NPN outputs
G70V-SOC16P(-C4)
2
NPN or
PNP
XW2Z-RI@@@
-@@MN
1
Inputs *2
G70V-SID16P(-1)(-C16)
2
PNP
XW2Z-RO@@@
-@@MN
1
PNP outputs
G70V-SOC16P-1(-C4)
2
Polarity
Specifications
Model *1
Model
Quantity
required
Input Units
LX41C4
32 inputs
QX41/QX41-S1/
QX41-S2
QX71
1 Fujitsu
connector
RX41C4
NPN or
PNP
LX42C4
QX42/QX42-S1
64 inputs
QX82/QX82-S1
A
2 Fujitsu
connectors
1:2
B
RX42C4
Output Units
LY41NT1P
QY41P
QY71
32
outputs
1 Fujitsu
connector
NPN
RY41NT2P
A
LY41PT1P
RY41PT1P
1 Fujitsu
connector
PNP
RY41PT2H
1:2
LY42NT1P
RY42NT2P
64
outputs
2 Fujitsu
connectors
NPN
QY42P
B
LY42PT1P
RY42PT1P
2 Fujitsu
connectors
QY82P
Mixed I/O Units
RH42C4NT2P
(Input side)
RH42C4NT2P
(Output side)
QH42P
(Input side)
QH42P
(Output side)
32 inputs
and 32
outputs
QX41Y41P
(Input side)
QX41Y41P
(Output side)
LH42C4NT1P
(Input side)
LH42C4NT1P
(Output side)
LH42C4PT1P
(Input side)
LH42C4PT1P
(Output side)
2 Fujitsu
connectors
2 Fujitsu
connectors
2 Fujitsu
connectors
2 Fujitsu
connectors
2 Fujitsu
connectors
B
1:2
Note: Cables that can be connected to the QX81, QX81-S2, and QY81P have not been prepared.
*1. The box @ is replaced by the cable length. For details on the types, refer to page 20.
*2. Either NPN inputs or PNP inputs can be used.
26
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have
any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing
by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE
PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL
SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products
or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election,
to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the
non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price
of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other
claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored,
installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or
unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in
writing, are not to be construed as an amendment or addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is
not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system,
or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with
respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it
to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice
to change part numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be
assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to
confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
OMRON Corporation
Industrial Automation Company
Authorized Distributor:
Kyoto, JAPAN
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69, 2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
© OMRON Corporation 2016-2018 All Rights Reserved.
In the interest of product improvement,
specifications are subject to change without notice.
CSM_2_9_1119
Cat. No. J215-E1-03
0318(0316)
