GRT1-END

P15E-EN-03B+SmartSlice+Datasheet.fm Seite 1 Dienstag, 30. August 2011 12:34 12 SmartSlice The smartest modular I/O system OMRON's SmartSlice I/O system is compact, intelligent and easy. When used with OMRON's CS1/CJ1 DeviceNet or CompoNet master units, no configuration tool is required. By using built-in functions such as pre-scaling, totalising, differentiation and alarming in analog I/O units, PLC programming can be minimised. Preventive maintenance data collected by all I/O units can be accessed using CX-Integrator or NS-series Smart Active Parts. • Most compact in the market (84 mm high) • Easy set-up, backup and restore functions • Diagnostics and preventive maintenance data at I/O level • Detachable terminal blocks allow hot-swapping without re-wiring • 3-wire I/O connection with 'push-in' technology, no screwdriver required System Configuration NJ series Controller, CS/CJ PLC series or Trajexia Motion Controller CX-One for setup, monitoring and operation of all OMRON Devices PLC Slave Communication Unit GRT1-TBR Right Turnback Unit GCN2-100 Turnback Cable (1 m) Max. 2 per station. I/O Units GRT1-END End Unit GRT1-TBL Left Turnback Unit Up to 64 I/O Units can be connected to a Communication Unit. SmartSlice 1 P15E-EN-03B+SmartSlice+Datasheet.fm Seite 2 Dienstag, 30. August 2011 12:34 12 Specifications General Specifications Common SmartSlice Specifications Unit power supply voltage 24 VDC (20.4 to 26.4 VDC) I/O power supply voltage 24 VDC (20.4 to 26.4 VDC) I/O connection Screwless push-in technology Noise immunity Conforms to IEC61000-4-4, 2.0 kV (power supply line) Vibration resistance 10 to 60 Hz: 0.7 mm double amplitude 60 to 150 Hz: 50 m/s2 Shock resistance 150 m/s2, 3 times in each direction Dielectric strength 500 VAC (between isolated circuits) Insulation resistance 20 M min. (between isolated circuits) Ambient operating temperature -10 to 55°C (with no icing or condensation) Ambient operating humidity 25% to 85% Operating environment No corrosive gases Ambient storage temperature -25 to 65°C (with no icing or condensation) Mounting 35 mm DIN rail Communication Units Model name Network Specification GRT1-PNT PROFINET-IO GRT1-PRT PROFIBUS-DPV1 Network connector 2 x RJ45, built-in switch with support for MRP redundancy. 9-pin D-Sub Network interface power supply Number of I/O points Number of connectable Units I/O power supply Status flags Parameter backup and restore 2 GRT1-DRT DeviceNet GRT1-CRT CompoNet Open-style 4-pin CompoNet DeviceNet connector, dual screwless push-in dual connections. Internal External, Internal 11 to 25 VDC, 22 mA 1,024 inputs and outputs max. (128 bytes each) 32 bytes input + 32 bytes output max. 64 SmartSlice I/O Units max. 24 VDC, 4 A max. 1 word for Communications Unit status flags up to 2 KB of data per I/O Unit. GRT1-ML2 GRT1-ECT MECHATROLINK-II EtherCAT for for Trajexia Trajexia and Sysmac (NJ) 2 x ML-II 2 x RJ45 1,024 inputs and outputs max. (128 bytes total) External 24 VDC (+10% - 15%) 1,024 inputs and outputs max. (128 bytes total) Control System P15E-EN-03B+SmartSlice+Datasheet.fm Seite 3 Dienstag, 30. August 2011 12:34 12 Digital Input Units Model name Signal type GRT1-ID4 GRT1-ID4-1 DC input (for sinking out- DC input (for sourcing puts, NPN type) outputs, PNP type) 4 inputs 4 x V (24 V) + 4 x G (0 V) 15 VDC min. 6 mA max./point (at 24 VDC) 5 VDC max. 1 mA max. 1.5 ms max. Number of input points Power terminals ON voltage ON current OFF voltage OFF current ON delay / OFF delay Model name Signal type Number of input points Power terminals Input voltage GRT1-IA4-1 AC input, 110 V 4 inputs None 100 to 120 VAC -15% to +10%, 50/60 Hz 70 VAC min. 4 mA min. 20 VAC max. 2 mA max. 10 ms max./55 ms max. ON voltage ON current OFF voltage OFF current ON delay / OFF delay V 2-wire sensor (such as a limit switch) 4 x V (24 V) 4 mA max./point (at 24 VDC) 200 to 240 VAC -15% to +10%, 50/60 Hz 120 VAC min. 10 ms max./40 ms max. GRT1-ID4 -1 (PNP) 0 – GRT1-ID8-1 DC input (for sourcing outputs, PNP type) GRT1-IA4-2 AC input, 230 V GRT1-ID4 (NPN) + GRT1-ID8 DC input (for sinking outputs, NPN type) 8 inputs 4 x G (0 V) 1 V Signal – 24 V + 0V 2-wire sensor (such as a limit switch) 3-wire sensor with NPN output (photoelectric or proximity sensor) 0 1 V V G G 2 3 Signal 24 V 0V G G 2 3 V V V V G G G G 3-wire sensor with NPN output (photoelectric or proximity sensor) GRT1-IA4-1/GRT1-IA4-2 0A 1A 0A 1A 0A 1A 0B 1B 0B 1B 0B 1B 0B 1B 0B 1B 0B 1B 2A 3A 2A 3A 2A 3A 2B 3B 2B 3B 2B 3B 2B 3B 2B 3B 2B 3B Note: Common signal for four inputs. V 0 1 G Signal 24 V GRT1-PC8-1 3-wire sensor 0V GRT1-ID8 Signal Signal V 3-wire sensor 24 V GRT1-ID8-1 (PNP) 3-wire sensor 24 V Signal 24 V GRT1-PD8 0V 3-wire sensor 0V GRT1-ID8 (NPN) 0V Note: No common signal for inputs. GRT1-ID8-1 G 0 1 V V 2 3 V V V V G G G G G G 2 3 V V 4 5 G G 4 5 V V 6 7 V V V V G G G G G G 6 7 3-wire sensor Signal 24 V – + 2-wire switch 0V 24 V 2-wire switch 0V – SmartSlice + External 24-V I/O power supply Signal − + 3-wire sensor 3 P15E-EN-03B+SmartSlice+Datasheet.fm Seite 4 Dienstag, 30. August 2011 12:34 12 Digital Output Units Model name Signal type Number of output points Power terminals Rated voltage GRT1-OD4 GRT1-OD4-1 Transistor output Transistor output (NPN type, sinking) (PNP type, sourcing) 4 outputs 4 x V (24 V) 4 x G (0 V) 24 VDC (20.4 to 26.4 VDC) Rated output current 500 mA max./point Residual voltage Leakage cuurent ON delay / Off delay 1.2 VDC max. (at 500 mA) 0.1 mA max. 0.5 / 1.5 ms max. Model name Signal type GRT1-OD8 Transistor output (NPN type, sinking) Number of output points 8 outputs Power terminals Rated voltage Rated output current Residual voltage Leakage cuurent ON delay / Off delay Mechanical life expectancy Electrical life expectancy 4 x V (24 V) 4 x G (0 V) 24 VDC (20.4 to 26.4 VDC) 500 mA max./point 1.2 VDC max. (at 500 mA) 0.1 mA max. 0.5 / 1.5 ms max. - GRT1-OD4 0 1 V GRT1-OD8-1 Transistor output (PNP type, sourcing) GRT1-OD4G-1 GRT1-OD4G-3 Transistor output (PNP type, sourcing), with short-circuit protection 4 x V (24 V) + 4 x G (0 V) 24 V I/O power supply via the front terminal of the unit. from 4 x 2.0 A at 30 °C to 4 x 1.0 A at 55 °C 1.2 VDC max. (at 2 A) GRT1-OD8G-1 GRT1-ROS2 Transistor output Relay output (PNP type, sourcing), (normally open) with short-circuit protection 2 outputs (with 2 terminals per connection) n.a. 250 VAC / 24 VDC 2 A (min. 1 mA @ 5 VDC) 15 ms max. 20,000,000 times min. 100,000 times min. GRT1-OD4-1 0 1 V NC NC NC NC G 2 3 V NC GRT1-OD4G-1 (PNP) 0 1 V V G G G 2 3 2 3 V NC NC V V NC G G G G Solenoid, valve, etc. 3-wire actuator GRT1-PC8-1 3-wire actuator Solenoid, valve, etc. GRT1-OD8 (NPN) Solenoid, valve, etc. 3-wire actuator GRT1-OD4G-3 (PNP) GRT1-OD8 G G 0 1 V V V V G G 0 1 G G V V Solenoid, valve, etc. 24 VDC G G 2 3 G G 4 5 V V V V 2 3 G G 6 7 G G Solenoid, valve, etc. 4 + 3-wire actucator 3-wire actuator Control System P15E-EN-03B+SmartSlice+Datasheet.fm Seite 5 Dienstag, 30. August 2011 12:34 12 GRT1-PC8 3-wire actuator GRT1-OD8(G)-1 (PNP) 3-wire actuator GRT1-ROS2 GRT1-OD8-1 V V 0 1 0 0 V V 2 3 C0 C0 G G G G NC NC V V 4 5 1 1 V V 6 7 C1 C1 G G G G NC NC Solenoid, valve, etc. AC power supply (or DC power supply) Load AC power supply (or DC power supply) Load 3-wire actuator Pulse I/O Units Model name Counter input GRT1-CT1 A/B incremental encoder, or pulse/direction, or pulse up/down 24 VDC, NPN type Counter signal type Max. frequency Counter range Comparison values Control Input Control Input functions GRT1-CT1-1 A/B incremental encoder, or pulse/direction, or pulse up/down 24 VDC, PNP type GRT1-CP1-L A/B/Z incremental encoder, or pulse/direction/reset 24 VDC, PNP type, or RS422 Line driver levels 100 kHz 60 kHz 32 bit double signed integer 1 range (2 comparison values) 2 independent ranges IN0, DC input (NPN type) IN0, DC input (PNP type) Capture, Preset, Reset Capture, Preset, Reset, Z enable OUT0, Transistor Output OUT0, Transistor Output OUT0, OUT1, Transistor (NPN, sinking) (PNP, sourcing) Output (PNP, sourcing) Range comparison, manual override On-the-fly reconfiguration, Frequency measurement Control Outputs Control Output functions Additional functions Note: Pulse I/O Units are not supported by GRT1-ML2 and GRT1-ECT. GRT1-CT1(-1) GRT1-CP1-L GRT1-CT1 (NPN) 24-V rotary encoder (all DIP switch pins ON) GRT1-CT1-1 (PNP) Line driver rotary encoder (all DIP switch pins OFF) A OUT A OUT A N.C. A+ A– B V B N.C. B N.C. B+ B– Z/IN N.C. Z/IN G Z N.C. Z+ Z– N.C. N.C. N.C. N.C. IN OUT0 IN OUT0 V V V V V OUT1 V OUT1 G G G G G G G G SmartSlice 5 P15E-EN-03B+SmartSlice+Datasheet.fm Seite 6 Dienstag, 30. August 2011 12:34 12 Analog I/O Units Model name Signal type GRT1-AD2 Analog Input: 0-20mA, 4-20mA, ±10V, 0-10V, 0-5V, 1-5V 2 inputs 1/6000 full scale 2ms / 2points GRT1-DA2V GRT1-DA2C Analog Output: Analog Output: ±10V, 0-10V, 0-5V, 1-5V 0-20mA, 4-20mA, Model name Signal type GRT1-TS2P Temperature input, Pt100, (2-wire, 3-wire) GRT1-TS2PK GRT1-TS2T Temperature input, Thermocouple, Pt1000, (2-wire, 3-wire) R, S, K, J, T, E, B, N, L, U, W, or PL2 Number of points Indication range 2 inputs -200 to +200 °C / -200 to +850 °C ±0.3% of PV or ±0.8 °C* (whichever is larger) ±1 digit max. * (or ±0.5 °C for -200 °C to +200 °C input range) Number of points Resolution Conversion time Accuracy Resolution GRT1-AD2 GRT1-DA2V NC NC 0+ 1+ GRT1-DA2C NC NC NC NC NC NC NC NC NC NC NC NC I0 + I1 + IN1 IN0 0- 1- AG AG Sh0 Sh0 V0 + V1 + OUT 0 Sh1 Sh1 GRT1-TS2P/PK (2-wire) 6 Depends on thremocouple type ±2°C ±1 digit max. Mounting restrictions apply. See Operation Manual W455 0.1 °C, 16-bit signed integer, or 0.01 °C, 32-bit signed double integer 250 ms / 2 points Conversion time Short for IN0 current input 2 outputs Short for IN1 current input 0- 1- NC NC GRT1-TS2P/PK (3-wire) 0A 1A 0A 1A 0B 1B 0B 1B 0B 1B 0B 1B SHT SHT 0A 1A SHT SHT 0A 1A SHT SHT 0B 1B SHT SHT 0B 1B NC NC NC NC OUT 0 OUT 1 OUT 1 0- 1- NC NC GRT1-TS2T Thermocouple input NC NC 0− 1− 0+ 1+ NC NC NC NC Cold Junction Sensor (do not remove) Control System P15E-EN-03B+SmartSlice+Datasheet.fm Seite 7 Dienstag, 30. August 2011 12:34 12 Power Feed and Distribution Units GRT1-PD2 24 VDC GRT1-PD2G NC NC NC NC V(R) NC NC RESET NC 24 VDC V V NC V V NC NC G G V V V V V V G G V V G G G G NC NC NC NC GRT1-PD8-1 24 VDC GRT1-PD8 GRT1-PC8 24 VDC GRT1-PC8-1 G G V V G G V V V V V V G G G G G G G G V V G G V V V V V V G G G G G G SmartSlice 7 P15E-EN-03B+SmartSlice+Datasheet.fm Seite 8 Dienstag, 30. August 2011 12:34 12 Dimensions I/O-units Communication Units GRT1-CRT GRT1-DRT GRT1-ECT GRT1-ML2 GRT1-PNT GRT1-PRT GRT1-TBL End units GRT1-END GRT1-END-M GRT1-TBR 8 Control System P15E-EN-03B+SmartSlice+Datasheet.fm Seite 9 Dienstag, 30. August 2011 12:34 12 Ordering Information Communication Units Function DeviceNet interface unit CompoNet interface unit PROFIBUS-DP interface unit PROFINET-IO interface unit MECHATROLINK-II interface unit EtherCAT interface unit End plate End plate with memory function Specification For up to 64 I/O units For up to 64 I/O units (limited to 32 byte in + 32 byte out) For up to 64 I/O units For up to 64 I/O units For up to 64 I/O units (slave to Trajexia motion controller) For up to 64 I/O units (slave to Trajexia and Sysmac controllers) One unit required per bus interface Supports toolless replacement of PROFINET-IO interface unit 84x58x70 84x58x70 84x58x70 84x58x70 84x58x70 84x58x70 84x20x58 84x20x58 Model code GRT1-DRT GRT1-CRT GRT1-PRT GRT1-PNT GRT1-ML2 GRT1-ECT GRT1-END GRT1-END-M 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 Model code GRT1-ID4 GRT1-ID4-1 GRT1-ID8 GRT1-ID8-1 GRT1-IA4-1 GRT1-IA4-2 GRT1-OD4 GRT1-OD4-1 GRT1-OD4G-1 GRT1-OD4G-3 GRT1-OD8 GRT1-OD8-1 GRT1-OD8G-1 GRT1-ROS2 GRT1-CT1 GRT1-CT1-1 GRT1-CP1-L 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 GRT1-AD2 GRT1-DA2V GRT1-DA2C GRT1-TS2P GRT1-TS2PK GRT1-TS2T 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x15x74 84x20x58 84x58x70 1m Model code GRT1-PD2 GRT1-PD2G GRT1-PD8 GRT1-PD8-1 GRT1-PC8 GRT1-PC8-1 GRT1-TBR GRT1-TBL GCN2-100 I/O units Function 4 NPN inputs 4 PNP inputs 8 NPN inputs 8 PNP inputs 4 AC inputs 4 AC inputs 4 NPN outputs 4 PNP outputs 4 PNP outputs with short-circuit protection 4 PNP outputs with short-circuit protection 8 NPN outputs 8 PNP outputs 8 PNP outputs with short-circuit protection 2 relay outputs 60 kHz Counter unit, NPN 60 kHz Counter unit, PNP 100 kHz Counter / Positioner unit 2 analog inputs, current/voltage 2 analog outputs, voltage 2 analog outputs, current 2 Pt100 inputs 2 Pt1000 inputs 2 Thermocouple inputs Specification 24 VDC, 6 mA, 3-wire connection 24 VDC, 6 mA, 3-wire connection 24 VDC, 4 mA, 1-wire connection + 4xG 24 VDC, 4 mA, 1-wire connection + 4xV 110 VAC, 2-wire connection 230 VAC, 2-wire connection 24 VDC, 500 mA, 2-wire connection 24 VDC, 500 mA, 2-wire connection 24 VDC, 500 mA, 3-wire connection 24 VDC, 2 A, 2-wire connection 24 VDC, 500 mA, 1-wire connection + 4xV 24 VDC, 500 mA, 1-wire connection + 4xG 24 VDC, 500 mA, 1-wire connection + 4xG 240 VAC, 2A, normally-open contacts A+B encoder inputs + 1 Z/control input + 1 output (NPN-type) A+B encoder inputs + 1 Z/control input + 1 output (PNP-type) A+B+Z encoder inputs (line driver or 24 V selectable) + 1 control input + 2 outputs (PNP-type) ±10 V, 0-10 V, 0-5 V, 1-5 V, 0-20 mA, 4-20 mA ±10 V, 0-10 V, 0-5 V, 1-5 V 0-20 mA, 4-20 mA Pt100, 2-wire or 3-wire connection Pt1000, 2-wire or 3-wire connection Types B, E, J, K, N, R, S, T, U, W, PL2, with cold junction compensation Other units Function I/O power feed unit, separates power supply between groups of I/O units I/O power feed unit with electronic overload protection, separates power supply between groups of I/O units I/O power feed and distribution unit, separates power supply between groups of I/O units, 8xV + 4xG I/O power feed and distribution unit, separates power supply between groups of I/O units, 4xV + 8xG I/O power connection unit, 8xV + 4xG I/O power connection unit, 4xV + 8xG Turnback Unit, right-hand side Turnback Unit, left-hand side Turnback cable, one meter Accessories Function Replacement front connectors, pack of 5 pcs. PROFIBUS-DP connector, 9-pin D-sub PROFIBUS-DP connector, 9-pin D-sub, with bus termination CompoNet screw terminal connector (order per 10 pcs) CompoNet branch line connector (order per 10 pcs) CompoNet Y-connector (order per 10 pcs) SmartSlice Model code GRT1-BT1-5 PROFIBUS Connector 839550 PROFIBUS Term. Conn. 846086 DCN4-TB4 DCN4-BR4 DCN4-MD4 9 P15E-EN-03B+SmartSlice+Datasheet.fm Seite 10 Dienstag, 30. August 2011 12:34 12 Master Units Function PROFINET-IO Controller for CJ1-series PLCs PROFIBUS-DP Master Unit for CS1-series PLCs PROFIBUS-DP Master Unit for CJ1-series PLCs DeviceNet Master Unit for CS1-series PLCs DeviceNet Master Unit for CJ1-series PLCs CompoNet Master Unit for CS1-series PLCs CompoNet Master Unit for CJ1-series PLCs MECHATROLINK-II Master Unit for Trajexia (4 stations max.) MECHATROLINK-II Master Unit for Trajexia (16 stations max.) EtherCAT Master Unit for Trajexia HMI with PLC and DeviceNet Master HMI with PLC and PROFIBUS-DP Master Model code CJ1W-PNT21 CS1W-PRM21 CJ1W-PRM21 CS1W-DRM21-V1 CJ1W-DRM21 CS1W-CRM21 CJ1W-CRM21 TJ1-ML04 TJ1-ML16 TJ2-ECT@@ NSJxx-T@@@@-G5D NSJxx-T@@@@-G5P Software Function CX-One, Omron's integrated software for programming and configuration of all control system components, including PLCs, remote I/O, HMI, servo drives, inverters, temperature controllers and advanced sensors. Cat. No. P15E-EN-03B Model code CX-ONE-AL@@ C-E @@ = number of licenses (01, 03, 10) In the interest of product improvement, specifications are subject to change without notice. OMRON EUROPE B.V. Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands Phone: +31 23 568 13 00 Fax: +31 23 568 13 88 www.industrial.omron.eu 10 Control System