K8DT-PM1TN

  Three-Phase Voltage and Phase-Sequence Phase-Loss Relay                                                                             Models with transistor outputs for superior contact reliability. added         •                                                                                                                                          Accessory (Order Separately)                                                                                                    ±0.5% rated power full scale (at 25˚C snf 65% humidity,   supply DC or 50/60 Hz sine wave input)  voltage                                                                                                         atset value  100% operation                                      OVER/UNDR: Red                                                                                                                                                                                                                       Stranded wires  or ferrules                                                                                                                                                                                                                Overvoltage  set value                                                                              voltages below 60% of the rated input.  go                                                                                                                                                         Lit when is an (lit for normal operation)  there   output         Lit    for overvoltage error.                           for undervoltage error.  Lit                                                                                                                               with or without                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             Accessories Separately)  (Order          DIN Track Mounting                   K8DT-PM                                                                                                          the as shown in Connection Diagram 2.  auxiliary relay operates,      Close cycle  counter  to measure  the switch and use the    the  operating time.              input value will equal the operating the input      value when    exceeds the set value and the alarm indicator starts flashing.                                                                                                                                  Slide Resistor                            Connection Diagram 1 Overvoltage    L1 L1  3-phase,   200 VAC L1 L2  0 to 150 V  L3               L2 L2 L3 L3 Undervoltage  3-phase variable autotransformer                                                   ?/8H$DA EbR`aV\[` N[Q 5[`dR_` > > @\NQ$`VQR DUN`R @\`` =[ ]_V[PV]YR% ]UN`R Y\`` PN[[\a OR QRaRPaRQ \[ aUR Y\NQ `VQR ORPNb`R aUR >17G&C@ ZRN`b_R` aU_RR&]UN`R c\YaNTR a\ QRaR_ZV[R ]UN`R Y\``' A\a\_ @\NQ DUN`R @\`` Qb_V[T C]R_NaV\[ @\a\_ Y\NQ ]UN`R Y\`` PN[[\a OR QRaRPaRQ Qb_V[T \]R_NaV\[' =a PN[ OR b`RQ a\ QRaRPa ]UN`R Y\`` Na `aN_ab]' A\_ZNYYf% aU_RR&]UN`R Z\a\_` dVYY P\[aV[bR a\ _\aNaR RcR[ VS \[R ]UN`R V` \]R[' GUR aU_RR&]UN`R c\YaNTR dVYY OR V[QbPRQ Na aUR Z\a\_ aR_ZV[NY`' GUR QVNT_NZ `U\d` c\YaNTR V[QbPaV\[ Na aUR Z\a\_ aR_ZV[NY` dUR[ ]UN`R E UN` ORR[ Y\`a dVaU N Y\NQ N]]YVRQ a\ N aU_RR&]UN`R Z\a\_' GUR U\_Vg\[aNY NeV` `U\d` aUR Z\a\_ Y\NQ N` N ]R_PR[aNTR \S aUR _NaRQ Y\NQ% N[Q aUR cR_aVPNY NeV` `U\d` c\YaNTR N` N ]R_PR[aNTR \S aUR _NaRQ c\YaNTR' GUR YV[R` V[ aUR T_N]U `U\d aUR c\YaNTR V[QbPRQ Na aUR Z\a\_ aR_ZV[NY` S\_ RNPU Y\NQ ]UN`R Y\`` \PPb_` Qb_V[T \]R_NaV\[' 4` aUR T_N]U `U\d`% ]UN`R Y\`` PN[[\a OR QRaRPaRQ ORPNb`R aUR Z\a\_ aR_ZV[NY c\YaNTR Q\R` [\a Q_\] cR_f ZbPU RcR[ VS N ]UN`R V` Y\`a dUR[ aUR Y\NQ \[ aUR Z\a\_ V` YVTUa' G\ QRaRPa Z\a\_ Y\NQ ]UN`R Y\`` Qb_V[T \]R_NaV\[% b`R aUR b[QR_c\YaNTR QRaRPaV\[ Sb[PaV\[ a\ QRaRPa aUR Z\a\_ aR_ZV[NY c\YaNTR` Na ]UN`R Y\``' FRa aUR \]R_NaV[T aVZR PN_RSbYYf ORPNb`R Va dVYY NSSRPa aUR aVZR S_\Z dUR[ aUR ]UN`R Y\`` \PPb_` b[aVY a_V]]V[T dUR[ aUV` Sb[PaV\[ V` b`RQ' 7UN_NPaR_V`aVP 7b_cR 8VNT_NZ ;RVI+!JYZd!TYRcRTeVcZdeZT!TfcgV!dY`hd!eYV!Raac`iZ^ReV! gR]fVd!`_]j( L`]eRXV!$Rd!R!aVcTV_eRXV!`W!cReVU!g`]eRXV% > +** 3/ LIJ 3* 2/ 2* LJH 1/ 1* 0/ 0* // /* LHI ./ * +* ,* -* .* /* 0* 1* 2* 3* +** ++* C`e`c!]`RU!$Rd!R!aVcTV_eRXV!`W!cReVU!]`RU% B\aR1 9\_ ]UN`R Y\`` \S ]UN`R E' IFG% IGE% N[Q IEF V[QVPNaR aUR Z\a\_ aR_ZV[NY c\YaNTR Na ]UN`R Y\``' >` N[ \cR_c\YaNTR QRaRPaRQ VS \[Yf \[R \S aUR aU_RR$]UN`R ]UN`R$a\$]UN`R c\YaNTR` RePRRQ` aUR \cR_c\YaNTR `Ra cNYbR4 GUR >17G Z\[Va\_` NYY aU_RR ]UN`R c\YaNTR`' GUR_RS\_R% N[ \cR_c\YaNTR V` QRaRPaRQ VS \[Yf \[R \S aUR ]UN`R&a\&]UN`R c\YaNTR` RePRRQ` aUR `Ra cNYbR' GUR `NZR V` a_bR S\_ b[QR_c\YaNTR`' ?/8H$DA GNSRaf D_RPNbaV\[` 6R `b_R a\ _RNQ aUR ]_RPNbaV\[` S\_ NYY Z\QRY` V[ aUR dRO`VaR Na aUR S\YY\dV[T IF@1 Uaa]1&&ddd%VN%\Z_\[%P\Z&% KN_[V[T >[QVPNaV\[` >[QVPNaR` N ]\aR[aVNYYf UNgN_Q\b` `VabNaV\[ dUVPU# VS [\a Nc\VQRQ# dVYY _R`bYa V[ ZV[\_ \_ Z\QR_NaR V[Wb_f# \_ ZNf _R`bYa V[ `R_V\b` V[Wb_f \_ QRNaU% 5QQVaV\[NYYf# aUR_R ZNf OR `VT[VSVPN[a ]_\]R_af QNZNTR% 75IH>CB >[QVPNaR` N ]\aR[aVNYYf UNgN_Q\b` `VabNaV\[ dUVPU# VS [\a Nc\VQRQ# ZNf _R`bYa V[ ZV[\_ \_ Z\QR_NaR V[Wb_f \_ V[ ]_\]R_af QNZNTR% D_RPNbaV\[` S\_ GNSR I`R Gb]]YRZR[aN_f P\ZZR[a` \[ dUNa a\ Q\ \_ Nc\VQ Q\V[T# a\ b`R aUR ]_\QbPa `NSRYf% D_RPNbaV\[` S\_ 7\__RPa I`R Gb]]YRZR[aN_f P\ZZR[a` \[ dUNa a\ Q\ \_ Nc\VQ Q\V[T# a\ ]_RcR[a SNVYb_R a\ \]R_NaR# ZNYSb[PaV\[# \_ b[QR`V_NOYR RSSRPa` \[ ]_\QbPa ]R_S\_ZN[PR% 9YRPa_VPNY `U\PX ZNf \PPN`V\[NYYf PNb`R `R_V\b` V[Wb_f% 7\[SV_Z aUNa aUR V[]ba c\YaNTR V` C;; ORS\_R `aN_aV[T N[f dV_V[T d\_X N[Q dV_R NYY P\[[RPaV\[` P\__RPaYf% 8\V[T `\ ZNf \PPN`V\[NYYf _R`bYa V[ ZV[\_ V[Wb_f QbR a\ RYRPa_VP `U\PX% 8\ [\a a\bPU aUR FRYNf dUVYR aUR ]\dR_ `b]]Yf V` CB# RePR]a S\_ aUR NQWb`aZR[a X[\O% HUR_R V` N _V`X \S ZV[\_ RYRPa_VPNY `U\PX# SV_R# \_ QRcVPR SNVYb_R% 8\ [\a NYY\d N[f ]VRPR` \S ZRaNY# P\[QbPa\_`# \_ PbaaV[T PUV]` aUNa \PPb_ Qb_V[T aUR V[`aNYYNaV\[ ]_\PR`` a\ R[aR_ aUR ]_\QbPa% ARN[V[T \S D_\QbPa GNSRaf GfZO\Y` I`RQ a\ dN_[ \S aUR _V`X \S RYRPa_VP `U\PX b[QR_ `]RPVSVP P\[QVaV\[`% I`RQ S\_ TR[R_NY ]_\UVOVaV\[` S\_ dUVPU aUR_R V` [\ `]RPVSVP `fZO\Y% I`RQ a\ V[QVPNaR ]_\UVOVaV\[ dUR[ aUR_R V` N _V`X \S ZV[\_ V[Wb_f S_\Z RYRPa_VPNY `U\PX \_ \aUR_ `\b_PR VS aUR ]_\QbPa V` QV`N``RZOYRQ% I`RQ S\_ TR[R_NY ZN[QNa\_f NPaV\[ ]_RPNbaV\[` S\_ dUVPU aUR_R V` [\ `]RPVSVRQ `fZO\Y% 9e]Y\`V\[` ZNf PNb`R ZV[\_ V[Wb_VR`% 8\ [\a b`R aUR ]_\QbPa V[ Y\PNaV\[` dVaU V[SYNZZNOYR \_ Re]Y\`VcR TN`R`% HUR_R V` N _V`X \S ZV[\_ RYRPa_VPNY `U\PX# SV_R# \_ QRcVPR SNVYb_R% 8\ [\a QV`N``RZOYR# Z\QVSf# _R]NV_# \_ a\bPU aUR V[`VQR \S aUR ]_\QbPa% I`R \S aUR ]_\QbPa ORf\[Q Va` YVSR ZNf _R`bYa V[ P\[aNPa dRYQV[T \_ Ob_[V[T% ANXR `b_R a\ P\[`VQR_ aUR NPabNY \]R_NaV[T P\[QVaV\[` N[Q b`R aUR ]_\QbPa dVaUV[ Va` _NaRQ Y\NQ N[Q RYRPa_VPNY YVSR P\b[a% HUR YVSR \S aUR \ba]ba _RYNf cN_VR` `VT[VSVPN[aYf dVaU aUR `dVaPUV[T PN]NPVaf N[Q `dVaPUV[T P\[QVaV\[`% >S aUR FRYNf V` b`RQ dVaU V[P\__RPa dV_V[T# SV_R ZNf \PPN`V\[NYYf \PPb_# ]\``VOYf _R`bYaV[T V[ ]Uf`VPNY QNZNTR% 7URPX aUR dV_V[T S\_ ZV`aNXR` ORS\_R f\b ab_[ CB aUR ]\dR_ `b]]Yf% >S aUR FRYNf SNVY`# Z\[Va\_V[T N[Q NYN_Z \ba]ba` ZNf SNVY a\ \]R_NaR% HUV` ZNf _R`bYa V[ ]Uf`VPNY QNZNTR a\ aUR SNPVYVaVR`# R^bV]ZR[a# \_ \aUR_ QRcVPR` aUNa N_R P\[[RPaRQ a\ Va% H\ _RQbPR aUV` _V`X# V[`]RPa aUR FRYNf _RTbYN_Yf% H\ ZNV[aNV[ `NSRaf V[ aUR RcR[a \S ZNYSb[PaV\[ \S aUR FRYNf# aNXR N]]_\]_VNaR `NSRaf ZRN`b_R`# `bPU N` V[`aNYYV[T N Z\[Va\_V[T QRcVPR \[ N `R]N_NaR YV[R% >S aUR dV_R V[`R_aV\[ YR[TaU V` V[`bSSVPVR[a# SV_R ZNf \PPN`V\[NYYf \PPb_# ]\``VOYf _R`bYaV[T V[ ]Uf`VPNY QNZNTR% >[`R_a aUR dV_R` NYY aUR dNf a\ aUR ONPX% HUR aR_ZV[NY OY\PX ZNf OR QNZNTRQ VS f\b V[`R_a N SYNa$OYNQR `P_RdQ_VcR_ V[ aUR _RYRN`R U\YR dVaU RePR``VcR S\_PR% >[`R_a aUR SYNa$OYNQR `P_RdQ_VcR_ V[a\ aUR _RYRN`R U\YR` dVaU N S\_PR \S (, B \_ YR``% K8DT-PM Precautions for Safe Use 1. Do not use or store the product in the following locations. • Locations subject to water or oil • Outdoor locations or under direct sunlight • Locations subject to dust or corrosive gases (sulfurizing gases, ammonia gases, etc.) • Locations subject to rapid temperature changes • Locations prone to icing and dew condensation • Locations subject to static electricity or noise • Locations subject to insects or small animals • Locations subject to direct radiant heat from heating equipment 2. Use and store the product in a location where the ambient temperature and humidity are within the specified ranges. If applicable, provide forced cooling. 3. Check terminal polarity when wiring and wire all connections correctly. The power supply terminals do not have polarity. 4. Do not wire the input and output terminals incorrectly. 5. Make sure the power supply voltage and loads are within the specifications and ratings for the product. 6. Make sure the ferrule terminals for wiring are of the specified size. 7. Make sure the stripping length is 8 mm. Insert the wires all the way to the back. 8. Do not connect anything to terminals that are not being used. 9. Use a power supply that will reach the rated voltage within 1 second after the power is turned ON. 10.Keep wiring separate from high voltages and power lines that draw large currents. Do not place product wiring in parallel with or in the same path as high-voltage or high-current lines. 11.Do not install the product near equipment that generates high frequencies or surges. 12.The product may cause incoming radio wave interference. Do not use the product near radio wave receivers. 13.Install an external switch or circuit breaker and label it clearly so that the operator can quickly turn OFF the power supply. 14.Make sure the indicators operate correctly. Depending on the application environment, the indicators may deteriorate prematurely and become difficult to see. 15.Do not use the product if it is accidentally dropped. The internal components may be damaged. 16.Be sure you understand the contents of this catalog and handle the product according to the instructions provided. 17.Do not install the product in any way that would place a load on it. 18.When discarding the product, properly dispose of it as industrial waste. 19. The product must be handled only by trained electricians. 20. Prior to operation, check the wiring before you supply power to the product. 21.Do not install the product immediately next to heat sources. 22.Perform periodic maintenance. 23. Do not wire anything to the release holes. 24. When you insert a flat-blade screwdriver into a release hole, do not tilt or twist the screwdriver. The terminal block may be damaged. 25. Insert a flat-blade screwdriver into the release holes at an angle. The terminal block may be damaged if the screwdriver is inserted straight in. 26. Do not allow the flat-blade screwdriver to fall when you are holding it in a release hole. 27. Do not bend a wire past its natural bending radius or pull in it with excessive force. Doing so may break the wires. 28. Do not insert more than one wire into each terminal insertion hole. 29.To prevent wire materials from smoking or igniting, use the wiring materials given in the following table. 10 Without Ferrules With Ferrules 0.25 to 1.5mm2/Equivalent to AWG24 to 16 10 mm 8 mm Note: Please use Ferrules with UL certification (R/C). 30.Use only the specified wires for wiring. 31.When wiring the terminals, allow some leeway in the wire length. 32.Make sure that the power supply is turned OFF before you change any DIP switch setting. Precautions for Correct Use • Locations subject to vibration and large shocks • Locations subject to wind and rain Stripping length Recommended wire Observe the following operating methods to prevent failure and malfunction. 1. Use the power supply voltage, input power, and other power supplies and converters with suitable capacities and rated outputs. 2. The distortion in the input waveform must be 30% max. If the input waveform is distorted beyond this level, it may cause unnecessary operation. 3. Error will be large if the product is used for thyristor or inverter control. 4. When cleaning the product, do not use thinners or solvents. Use commercial alcohol. 5. If you use stranded wires, make sure that there are no loose wire strands. 6. If you wire crossovers and connect terminal blocks in parallel, a large current will flow. Make sure that the current does not exceed 10 A. 7. The terminal block may be damaged if the recommended tool is not used. Use the recommended flat-blade screwdriver to operate the release holes. Correct Mounting Direction, Mounting, and Removing Mounting to DIN Track To mount the Relay to a DIN Track, hook the Relay onto the DIN Track and press the Relay in the direction of the arrow until you hear it lock into place. (1) (2) Removing from the DIN Track To remove the Relay, insert a screwdriver into the hook on the top or bottom and pull out the hook to release the Relay. Applicable DIN Tracks PFP-100N (100 cm) PFP-50N (50 cm) 30 mm min. • Leave at least 30 mm of space between the product and other devices to allow easy installation and removal.                                                                                                                                                                                                                          To  prevent  short  circuits,  insert  the  stripped  part  of  a  stranded  wire  or the conductor part of a ferrule it is hidden      until     inside                                                                The method  is  used  to remove stranded wires  and ferrules.  same                                                                                                                           K8DT-PM Recommended Ferrules and Tools EN/IEC Standard Compliance Recommended Ferrules Wire (mm2) (AWG) Recommended ferrules Ferrule length (mm) Manufactured Manufactured Manufactured by Phoenix by by Wago Contact Weidmuller 0.25 24 8 AI0.25-8 H0.25/12 FE-0.25-8N-YE 0.34 22 8 AI0.34-8 H0.34/12 FE-0.34-8N-TQ 0.5 20 8 AI0.5-8 H0.5/14 FE-0.5-8N-WH 0.75 18 8 AI0.75-8 H0.75/14 FE-0.75-8N-GY 1 18 8 AI1-8 H1.0/14 FE-1.0-8N-RD 1.5 16 8 AI1.5-8 H1.5/14 FE-1.5-8N-BK PZ6 roto Variocrimp4 CRIMPFOX6 CRIMPFOX6T-F CRIMPFOX10S Recommended crimp tool Note: 1. Make sure that the outer diameter of the wire coating is smaller than the inner diameter of the insulation sleeve of the recommended ferrule. 2. Make sure that the ferrule processing dimensions conform to the following figures. 8 mm 2.1 mm max. • Refer to the contents of this datasheet for cable selection and other conditions for compliance with EMC standards. Precaution on EN Standard Compliance The K8DT complies with EN 60947-5-1 when it is built into a panel, but observe the following handling methods to ensure compliance with the requirements of this standard. Wiring Overvoltage category III Pollution degree 2 • Open-frame Device • If basic, double, or reinforced insulation is required, use the basic, double, or reinforced insulation defined in IEC 60664 that is suitable for the maximum applied voltage for the clearance, solid insulation, and other factors. • There is basic insulation between the power supply terminals and input terminals. • There is basic insulation between the power supply terminals and output terminals. • There is basic insulation between the input terminals and output terminals. • Operating section must have reinforced or double insulation. • The sides of the case are not isolated. • Connect the output contacts (contacts with different polarity) so that they reach the same potential. 2.7 mm max. Recommended Flat-blade Screwdriver Use a flat-blade screwdriver to connect and remove wires. The following table shows manufacturers and models as of 2015/Dec. Side Front 2.5 mm dia. 0.4 mm 2.5 mm Model XW4Z-00B 12 Reinforced insulation (Double insulation) Manufacturer Omron ESD0.40 2.5 Wera SZF 0.4 2.5 Phoenix Contact 0.4 2.5 75 302 Wiha AEF.2.5 75 Facom 210-719 Wago SDI 0.4 2.5 75 Weidmuller Not isolated Terms and Conditions of Sale 1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed part of all quotes, agreements, purchase orders, acknowledgments, price lists, catalogs, manuals, brochures and other documents, whether electronic or in writing, relating to the sale of products or services (collectively, the "Products") by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron objects to any terms or conditions proposed in Buyer’s purchase order or other documents which are inconsistent with, or in addition to, these Terms. 2. Prices; Payment Terms. All prices stated are current, subject to change without notice by Omron. Omron reserves the right to increase or decrease prices on any unshipped portions of outstanding orders. Payments for Products are due net 30 days unless otherwise stated in the invoice. 3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices sent to Buyer after deducting transportation charges, taxes and duties, and will be allowed only if (i) the invoice is paid according to Omron’s payment terms and (ii) Buyer has no past due amounts. 4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or the maximum legal rate, whichever is less, on any balance not paid within the stated terms. 5. Orders. Omron will accept no order less than $200 net billing. 6. Governmental Approvals. Buyer shall be responsible for, and shall bear all costs involved in, obtaining any government approvals required for the importation or sale of the Products. 7. Taxes. All taxes, duties and other governmental charges (other than general real property and income taxes), including any interest or penalties thereon, imposed directly or indirectly on Omron or required to be collected directly or indirectly by Omron for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by Buyer to Omron. 8. Financial. If the financial position of Buyer at any time becomes unsatisfactory to Omron, Omron reserves the right to stop shipments or require satisfactory security or payment in advance. If Buyer fails to make payment or otherwise comply with these Terms or any related agreement, Omron may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid accounts. 9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation unless Buyer indemnifies Omron against all related costs or expenses. 10. Force Majeure. Omron shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron: a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship except in “break down” situations. b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall constitute delivery to Buyer; c. All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Omron), at which point title and risk of loss shall pass from Omron to Buyer; provided that Omron shall retain a security interest in the Products until the full purchase price is paid; d. Delivery and shipping dates are estimates only; and e. Omron will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions. 12. Claims. Any claim by Buyer against Omron for shortage or damage to the Products occurring before delivery to the carrier must be presented in writing to Omron within 30 days of receipt of shipment and include the original transportation bill signed by the carrier noting that the carrier received the Products from Omron in the condition claimed. 13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL- 14. 15. 16. 17. 18. ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron247.com or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and their employees from and against all liabilities, losses, claims, costs and expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Omron is a party) which arises or is alleged to arise from Buyer's acts or omissions under these Terms or in any way with respect to the Products. Without limiting the foregoing, Buyer (at its own expense) shall indemnify and hold harmless Omron and defend or settle any action brought against such Companies to the extent based on a claim that any Product made to Buyer specifications infringed intellectual property rights of another party. Property; Confidentiality. Any intellectual property in the Products is the exclusive property of Omron Companies and Buyer shall not attempt to duplicate it in any way without the written permission of Omron. Notwithstanding any charges to Buyer for engineering or tooling, all engineering and tooling shall remain the exclusive property of Omron. All information and materials supplied by Omron to Buyer relating to the Products are confidential and proprietary, and Buyer shall limit distribution thereof to its trusted employees and strictly prevent disclosure to any third party. Export Controls. Buyer shall comply with all applicable laws, regulations and licenses regarding (i) export of products or information; (iii) sale of products to “forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of regulated technology or information. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right and no course of dealing between Buyer and Omron shall operate as a waiver of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder without Omron's written consent. (c) Law. These Terms are governed by the law of the jurisdiction of the home office of the Omron company from which Buyer is purchasing the Products (without regard to conflict of law principles). (d) Amendment. These Terms constitute the entire agreement between Buyer and Omron relating to the Products, and no provision may be changed or waived unless in writing signed by the parties. (e) Severability. If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. (f) Setoff. Buyer shall have no right to set off any amounts against the amount owing in respect of this invoice. (g) Definitions. As used herein, “including” means “including without limitation”; and “Omron Companies” (or similar words) mean Omron Corporation and any direct or indirect subsidiary or affiliate thereof. Certain Precautions on Specifications and Use 1. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases but the following is a non-exhaustive list of applications for which particular attention must be given: (i) Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. (ii) Use in consumer products or any use in significant quantities. (iii) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this Product. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO 2. 3. 4. 5. ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com OMRON CANADA, INC. • HEAD OFFICE Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com OMRON ARGENTINA • SALES OFFICE Cono Sur • 54.11.4783.5300 OMRON ELECTRONICS DE MEXICO • HEAD OFFICE México DF • 52.55.59.01.43.00 • 01-800-226-6766 • mela@omron.com OMRON CHILE • SALES OFFICE Santiago • 56.9.9917.3920 OMRON ELECTRONICS DE MEXICO • SALES OFFICE Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • mela@omron.com OTHER OMRON LATIN AMERICA SALES 54.11.4783.5300 OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu Authorized Distributor: Automation Control Systems • Machine Automation Controllers (MAC) • Programmable Controllers (PLC) • Operator interfaces (HMI) • Distributed I/O • Software Drives & Motion Controls • Servo & AC Drives • Motion Controllers & Encoders Temperature & Process Controllers • Single and Multi-loop Controllers Sensors & Vision • Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors • Amplified Photomicrosensors • Measurement Sensors • Ultrasonic Sensors • Vision Sensors Industrial Components • RFID/Code Readers • Relays • Pushbuttons & Indicators • Limit and Basic Switches • Timers • Counters • Metering Devices • Power Supplies Safety • Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety Controllers • Light Curtains • Safety Relays • Safety Interlock Switches N49I-E-01 05/16 Note: Specifications are subject to change. Printed on recycled paper. © 2016 Omron Electronics LLC Printed in U.S.A.