S82Y-VK10F

New Product Switch Mode Power Supply S8VK-C (60/120/240/480-W Models) Cost-effective Single Phase Power Supply Universal input and Safety standards for worldwide applications Space-saving Compact Design • Universal input for worldwide applications: 100 to 240 VAC (85 to 264 VAC) • DC input can be available: 90 to 350 VDC • Operation temperature range: –25 to 60 °C • Compact Dimension for small space • Flexible installation by special mounting brackets • Safety standards: UL508/60950-1, CSA C22.2 No.107.1/60950-1 EN50178 (=VDE0160), EN60950-1 (=VDE0805) • EMS: Conform to EN61204-3 EMI: EN55011 Class A ! Refer to Safety Precautions for All Power Supplies and Safety Precautions on page 11. Model Number Structure Model Number Legend Note: Not all combinations are possible. Refer to List of Models in Ordering Information, below. S8VK-C @@@ 24 1 2 1. Power Ratings 060: 60 W 120: 120 W 240: 240 W 480: 480 W 2. Output voltage 24: 24 V Ordering Information Note: For details on normal stock models, contact your nearest OMRON representative. Power ratings Input voltage 60 W 120 W 240 W 480 W Output Voltage 24 V Single phase 100 to 240 VAC 90 to 350 VDC Output current 2.5 A Model number S8VK-C06024 24 V 5A S8VK-C12024 24 V 10 A S8VK-C24024 24 V 20 A S8VK-C48024 1 S8VK-C Specifications Ratings, Characteristics, and Functions Item Efficiency (Typical) Power ratings 60 W 120 W 240 W Output voltage 24 V 24 V 24 V 230 VAC input Voltage *1 Input Power factor (Typical) 89% 24 V 92% 50/60 Hz (47 to 450 Hz) 115 VAC input 1.0 A 2.0 A 2.5 A 4.8 A 230 VAC input 0.7 A 1.4 A 1.3 A 2.4 A 230 VAC input 0.44 0.45 0.92 0.97 Harmonic current emissions Output 89% 100 to 240 VAC, 90 to 350 VDC (allowable range: 85 to 264 VAC) *6 Frequency *1 Current (Typical) 88% 480 W --- Conforms to EN61000-3-2 Leakage current (Typical) 115 VAC input 0.19 mA 0.19 mA 0.24 mA 0.26 mA 230 VAC input 0.34 mA 0.36 mA 0.54 mA 0.65 mA Inrush current (Typical) *2 115 VAC input 16 A 230 VAC input 32 A 70 mV 130 mV Voltage adjustment range *3 –10% to 15% (with V.ADJ) (guaranteed) Ripple at 20 MHz (Typical) *4 70 mV 230 VAC input 120 mV Input variation influence 0.5% max. (at 85 to 264 VAC input, 100% load) Load variation Influence (Rated Input voltage) 1.5% max., at 0% to 100% load Temperature variation influence 0.05%/°C max. Start up time (Typical) *2 115 VAC input 530 ms 720 ms 790 ms 770 ms 230 VAC input 410 ms 510 ms 750 ms 670 ms Hold time (Typical) *2 115 VAC input 24 ms 27 ms 34 ms 21 ms 230 VAC input 117 ms 128 ms 36 ms 22 ms Overload protection *2 Additional Overvoltage protection *2 functions Parallel operation 105% to 160% of rated load current Yes *5 No Series operation Possible for up to two Power Supplies (with external diode) Ambient operating temperature –25 to 60°C (Refer to Engineering Data) Storage temperature –25 to 65°C Ambient operating humidity 20% to 90% (Storage humidity: 10% to 95%) Dielectric strength (detection current: 20 mA) 3.0 kVAC for 1 min. (between all inputs and outputs) 2.0 kVAC for 1 min. (between all inputs and PE terminal) 1.0 kVAC for 1 min. (between all outputs and PE terminal) Insulation resistance 100 MΩ min. (between all outputs and all inputs/ PE terminals) at 500 VDC 10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions Vibration resistance 10 to 150 Hz, 0.35-mm single amplitude (5 G max for 60W, 120W, 240 W, 3 G max for 480 W) for 80 min. each in X, Y, and Z directions Shock resistance 150 m/s2, 3 times each in ±X, ±Y, and ±Z directions Output indicatior Others EMI Yes (color: green), lighting from 80% to 90% or more of rated voltage Conducted Emission Conforms to EN61204-3 EN55011 Class A and based on FCC Class A Radiated Emission Conforms to EN61204-3 EN55011 Class A EMS Conforms to EN61204-3 high severity levels Approved Standards UL Listed: UL508 (Listing) UL UR: UL60950-1 (Recognition) cUL: CSA C22.2 No.107.1 cUR: CSA C22.2 No.60950-1 EN/VDE: EN50178 (=VDE0160), EN60950-1 (=VDE0805) Fulfilled Standards SELV (EN60950-1/EN50178/UL60950-1) EN50274 for Terminal parts Degree of protection IP20 by EN / IEC60529 SEMI F47-0706 (200 to 240 VAC) Weight 260 g 580 g 940 g 1,550 g *1. Do not use an inverter output for the Power Supply. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal temperature of the Power Supply may result in ignition or burning. *2. For a cold start at 25°C. Refer to Engineering Data on page 5 for details. *3. If the output voltage adjuster (V. ADJ) is turned, the voltage will increase by more than +15% of the voltage adjustment range. When adjusting the output voltage, confirm the actual output voltage from the Power Supply and be sure that the load is not damaged. *4. A characteristic when the ambient operating temperature is between –25 to 60°C. *5. To reset the protection, turn OFF the input power for three minutes or longer and then turn it back ON. *6. 90 to 350 VDC’s UL standards are scheduled to obtain certification in June, 2013. 2 S8VK-C Connections Block Diagrams S8VK-C06024 (60W) AC (L) INPUT +V Fuse: 250 VAC 6.3 A HBC +V −V DC OUTPUT Noise filter AC (N) Rectifier Inrush Smoothing current protection circuit Rectifier/ smoothing circuit −V −V Drive control circuit Voltage detection circuit Overcurrent detection circuit Overvoltage detection circuit Photocoupler S8VK-C12024 (120W) +V Fuse: 250 VAC 8.0 A HBC AC (L) INPUT +V −V DC OUTPUT Noise filter AC (N) Rectifier Rectifier/ smoothing circuit Inrush current Smoothing protection circuit circuit −V −V Drive control circuit Voltage detection circuit Overcurrent detection circuit Overvoltage detection circuit Photocoupler S8VK-C24024 (240W) +V Fuse: 250 VAC 8.0 A HBC AC (L) INPUT +V −V DC OUTPUT Noise filter AC (N) Inrush current Rectifier protection Harmonic current suppression circuit (Power factor improvement) Smoothing circuit Rectifier/ smoothing circuit −V −V Drive circuit Overcurrent detection circuit Drive control circuit Voltage detection circuit Overvoltage detection circuit Photocoupler S8VK-C48024 (480W) +V Fuse: 250 VAC 12.0 A HBC AC (L) INPUT +V −V DC OUTPUT Noise filter AC (N) Inrush current protection Rectifier Harmonic current Smoothing suppression circuit circuit (Power factor improvement) Rectifier/ smoothing circuit −V −V Drive circuit Drive control circuit Overcurrent detection circuit Voltage detection circuit Overvoltage detection circuit Photocoupler 3 S8VK-C Construction and Nomenclature Nomenclature 60-W Models 120-W Models 240-W Models 480-W Models S8VK-C06024 S8VK-C12024 S8VK-C24024 S8VK-C48024 3 3 3 4 4 4 4 5 5 5 5 1 2 1 No. 1 2 3 4 5 Name Input terminals (L), (N) Protective Earth terminal (PE) DC Output terminals (−V), (+V) Output indicator (DC ON: Green) Output voltage adjuster (V.ADJ) 2 1 2 1 2 Function Connect the input lines to these terminals. *1 Connect the ground line to this terminal. *2 Connect the load lines to these terminals. Lights while a direct current (DC) output is ON. Use to adjust the voltage. *1. The fuse is located on the (L) side. It is not user-replaceable. For a DC input, connect the positive voltage to the L terminal. *2. This is the protective earth terminal specified in the safety standards. Always ground this terminal. Engineering Data Derating Curve Load ratio (%) 60, 120, 240, 480 W 120 100 A 80 B 60 40 20 0 −40 −25 −10 0 10 20 30 40 50 60 70 80 Ambient temperature (°C) Note: 1. At less than 90 VAC, the derating is 2.5%/V 2. For a DC power input, reduce the load given in the above derating curve by multiplying the following coefficients. S8VK-C06024/S8VK-C12024: 0.8 S8VK-C24024/S8VK-C48024: 0.7 A. Standard mounting 40°C and over: the derating is 2.0%/°C B. Face-up mounting 30°C and over: the derating is 1.67%/°C 4 3 S8VK-C Overvoltage Protection (A) Standard (Vertical) mounting (B) Face-up mounting Overload Protection The load and the power supply are automatically protected from overcurrent damage by this function. Overload protection is activated if the output current rises above 105% of the rated current. When the output current returns within the rated range overload protection is automatically cleared. Consider the possibility of an overvoltage and design the system so that the load will not be subjected to an excessive voltage even if the feedback circuit in the Power Supply fails. If an excessive voltage that is approximately 130% of the rated voltage or more is output, the output voltage is shut OFF. Reset the input power by turning it OFF for at least three minutes and then turning it back ON again. Output voltage (V) Mounting +30% (approx.) Overvoltage protection operating +15% Rated output voltage Variable range −10% Output voltage (V) 0V The values shown in the above diagram is for reference only. Note: Do not turn ON the power again until the cause of the overvoltage has been removed. Inrush Current, Startup Time, Output Hold Time Intermittent operation Input ON 0 50 100 Output current (%) Input OFF AC input voltage The values shown in the above diagrams are for reference only. Note: 1. Internal parts may occasionally deteriorate or be damaged if a short-circuited or overcurrent state continues during operation. 2. Internal parts may possibly deteriorate or be damaged if the Power Supply is used for applications with frequent inrush current or overloading at the load end. Do not use the Power Supply for such applications. Inrush current on input application AC input current 96.5% 90% Output voltage Startup time (1,000 ms max.) Hold time (20 ms min.) Note: Twice the input current or above will flow during the parallel operation or redundant system. Therefore, check the fusing characteristics of fuses and operating characteristics of breakers making sure that the external fuses will not burn out and the circuit breakers will not be activated by the inrush current. 5 S8VK-C Two phases application for Single phase models For All Single phase Models, S8VK-C Basically OMRON single phase power supply can be used on twophases of a 3–phase-system when some of conditions satisfy like below. 1. The supplying voltage is below the maximum rated input. OMRON Power supply allows the input voltage equivalent or less than 240 VAC+10%. Please confirm the input voltage between two lines if the input voltage satisfies this condition before connecting. 2. The external protector is needed on N input line to secure a safety. N line has no protection of a fuse internally. An appropriate fuse or circuit breaker should be connected on N input line like the following. L1 L2 L3 PE Power Supply Internal Fuse A external fuse or a circuit breaker L N max. 240 VAC+10% Reference Value Value Reliability (MTBF) 6 Single phase model 60 W: 630,000 hrs 120 W: 490,000 hrs 240 W: 270,000 hrs 480 W: 190,000 hrs Definition MTBF stands for Mean Time Between Failures, which is calculated according to the probability of accidental device failures, and indicates reliability of devices. Therefore, it does not necessarily represent a life of the product. Life expectancy 10 yrs. Min. Definition The life expectancy indicates average operating hours under the ambient temperature of 40°C and a load rate of 50%. Normally this is determined by the life expectancy of the built-in aluminum electrolytic capacitor. S8VK-C Dimensions (Unit: mm) S8VK-C06024 (60 W) 5 (1) 110 3.6 dia. (Bit #1) 106 34.9 90 75.4 3.6 dia. (Bit #1) Rail Stopper 3.5 4.7 (Sliding: 10 max.) 7.62 32 S8VK-C12024 (120 W) 122.2 117.8 112.2 (1) 5.0 dia. (Bit #2) 6.35 104.6 (4) 34.7 125 5.0 dia. (Bit #2) Rail Stopper 4.7 (Sliding: 7.5 max.) 6.35 40 (10) S8VK-C24024 (240 W) 150 145.6 6.35 5.0 dia. (Bit #2) (1) (4) 140 125 104.6 34.7 5.0 dia. (Bit #2) Rail Stopper (10) 6.35 4.7 (Sliding: 7.5 max.) 60 S8VK-C48024 (480 W) (1) 150 145.6 140 (4) 125 34.7 52.3 5.0 dia. (Bit #2) 6.35 6.35 95 Rail Stopper 5.0 dia. (Bit #2) 4.7 (Sliding: 7.5 max.) (10) 7 S8VK-C DIN Rail (Order Separately) Note: All units are in millimeters unless otherwise indicated. Mounting Rail (Material: Aluminum) PFP-100N PFP-50N 7.3±0.15 4.5 35±0.3 15 25 10 25 25 10 1,000 (500) * 25 27±0.15 15(5) * 1 * Values in parentheses are for the PFP-50N. Mounting Rail (Material: Aluminum) PFP-100N2 16 4.5 35±0.3 27 15 25 10 25 25 10 1,000 25 15 24 29.2 1 1.5 End Plate PFP-M 10 6.2 M4×8 panhead screw 1.8 1 50 1.8 35.5 35.5 11.5 10 M4 spring washer 1.3 4.8 Note: If there is a possibility that the Unit will be subject to vibration or shock, use a steel DIN Rail. Otherwise, metallic filings may result from aluminum abrasion. 8 S8VK-C Mounting Brackets Name Front-mounting bracket (for 60 W models) Model S82Y-VS10F Front-mounting bracket (for 120, 240 and 480 W models) S82Y-VK10F Side-mounting bracket (for 60 W models) S82Y-VS10S Side-mounting bracket (for 120 W models) S82Y-VK10S Side-mounting bracket (for 240 W models) S82Y-VK20S Type Model Dimensions Appearance 41 4.5 dia.±0.1 35 25 Front-mounting bracket S82Y-VS10F (For 60 W models) 35±0.1 7.3 10 40 50 t = 1.0 (For 120 W types) Front-mounting bracket (for 120, 240 and 480 W models) (For 240 W types) 140±0.1 150 S82Y-VK10F 25±0.1 4.5 dia.±0.1 5.4 38 t = 2.0 9 S8VK-C Type Model Dimensions Appearance 4.5 dia.±0.1 55±0.1 35 Right-side mounting Left-side mounting Right-side mounting Left-side mounting Right-side mounting 60±0.1 80 Side-mounting bracket S82Y-VS10S (For 60 W models) Left-side mounting 13 64 t = 2.0 73 40 49 50±0.1 15.5±0.1 4.5 dia.±0.1 Side-mounting bracket (For 120 W models) S82Y-VK10S 140±0.1 125 150 t = 2.0 73 40 59 50±0.1 15.5±0.1 4.5 dia.±0.1 Side-mounting bracket (For 240 W models) 140±0.1 S82Y-VK20S 125 t = 2.0 10 150 S8VK-C Safety Precautions Warning Indications CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or in property damage. Precautions for Safe Use Supplementary comments on what to do or avoid doing, to use the product safely. Precautions for Correct Use Supplementary comments on what to do or avoid doing, to prevent failure to operate, malfunction or undesirable effect on product performance. Meaning of Product Safety Symbols Used to warn of the risk of electric shock under specific conditions. Used to warn of the risk of minor injury caused by high temperatures. Used for general mandatory action precautions for which there is no specified symbol. Use to indicate prohibition when there is a risk of minor injury from electrical shock or other source if the product is disassembled. !CAUTION Minor electric shock, fire, or Product failure may occasionally occur. Do not disassemble, modify, or repair the Product or touch the interior of the Product. Minor burns may occasionally occur. Do not touch the Product while power is being supplied or immediately after power is turned OFF. Fire may occasionally occur. Tighten terminal screws to the specified torque (0.5 to 0.6 N·m). Minor injury due to electric shock may occasionally occur. Do not touch the terminals while power is being supplied. Always close the terminal cover after wiring. Minor electric shock, fire, or Product failure may occasionally occur. Do not allow any pieces of metal or conductors or any clippings or cuttings resulting from installation work to enter the Product. 11 S8VK-C Precautions for Safe Use Wiring • Connect the ground completely. A protective earthing terminal stipulated in safety standards is used. Electric shock or malfunction may occur if the ground is not connected completely. • Minor fire may possibly occur. Ensure that input and output terminals are wired correctly. • Do not apply more than 75-N force to the terminal block when tightening it. • Be sure to remove the sheet covering the Product for machining before power-ON so that it does not interfere with heat dissipation. • Use the following material for the wires to be connected to the S8VK-C to prevent smoking or ignition caused by abnormal loads. Terminals and Wiring INPUT OUTPUT American Wire Gauge Solid Wire /Stranded Wire American Wire Gauge Solid Wire /Stranded Wire S8VK-C06024 AWG22 to 12 0.35 to 4 mm2 /0.35 to 2.5 mm2 AWG20 to 12 0.5 to 4 mm2 /0.5 to 2.5 mm2 S8VK-C12024 AWG22 to 10 0.35 to 6 mm2 /0.35 to 4 mm2 AWG18 to 10 0.75 to 6 mm2 /0.75 to 4 mm2 AWG20 to 10 0.5 to 6 mm2 /0.5 to 4 mm2 AWG14 to 10 2.5 to 6 mm2 /2.5 to 4 mm2 AWG12 to 10 4 to 6 mm2 /4 mm2 Model S8VK-C24024 2 S8VK-C48024 AWG16 to 10 1.5 to 6 mm /1.5 to 4 mm2 PE American Wire Gauge Solid Wire /Stranded Wire AWG14 or thicker 2.5 mm2 or thicker /2.5 mm2 or thicker • Strip I/O wires for 8 mm when using a screwless terminal block. Note: The rated current for output terminals is 10 A per terminal. Be sure to use multiple terminals simultaneously for current that exceeds the terminal rating. When applying a current of 10 A or more, use at least two terminals each for the positive and negative wires. Installation Environment • Do not use the Power Supply in locations subject to shocks or vibrations. In particular, install the Power Supply as far away as possible from contactors or other devices that are a vibration source. • Install the Power Supply well away from any sources of strong, high-frequency noise and surge. Operating Life • The life of a Power Supply is determined by the life of the electrolytic capacitors used inside. Here, Arrhenius Law applies, i.e., the life will be cut in half for each rise of 10°C or the life will be doubled for each drop of 10°C. The life of the Power Supply can thus be increased by reducing its internal temperature. 12 Ambient Operating and Storage Environments • Store the Power Supply at a temperature of −25 to 65°C and a humidity of 10% to 95%. • Do not use the Power Supply in areas outside the derating curve otherwise, internal parts may occasionally deteriorate or be damaged. • Use the Power Supply at a humidity of 20% to 90%. • Do not use the Power Supply in locations subject to direct sunlight. • Do not use locations where liquids, foreign matter, or corrosive gases may enter the interior of Products. S8VK-C Precautions for Correct Use Mounting DIN Rail Mounting • Take adequate measures to ensure proper heat dissipation to increase the long-term reliability of the Product. Be sure to allow convection in the atmosphere around devices when mounting. Do not use in locations where the ambient temperature exceeds the range of the derating curve. • When cutting out holes for mounting, make sure that cuttings do not enter the interior of the Products. To mount the Block on a DIN Rail, hook portion (A) of the Block onto the rail and press the Block in direction (B). (A) (B) *1 To dismount the Block, pull down portion (C) with a flat-blade screwdriver and pull out the Block. 30 mm min. *1. Convection of air *2. 20 mm min. • Improper mounting will interfere with heat dissipation and may occasionally result in deterioration or damage of internal parts. Use the Product within the derating curve for the mounting direction that is used. • Use a mounting bracket when the Product is mounted facing horizontally. • Heat dissipation will be adversely affected. When the Product is mounted facing horizontally, always place the side with the label facing upward. • Operate the Power Supply within a range that is 5°C less than the values in the derating curve in Engineering Data on page 4 if the Power Supply is used with an installation spacing of 10 mm min. (20 mm max.) on the left and right. Overcurrent Protection • Internal parts may possibly deteriorate or be damaged if a short-circuited or overcurrent state continues during operation. • Internal parts may possibly deteriorate or be damaged if the Power Supply is used for applications with frequent inrush current or overloading at the load end. Do not use the Power Supply for such applications. • The DC ON indicator (green) flashes if the overload protection function operates. Charging a Battery If you connect a battery as the load, install overcurrent control and overvoltage protection circuits. Output Voltage Adjuster (V.ADJ) • The output voltage adjuster (V.ADJ) may possibly be damaged if it is turned with unnecessary force. Do not turn the adjuster with excessive force. • After completing output voltage adjustment, be sure that the output capacity or output current does not exceed the rated output capacity or rated output current. (C) Track stopper Series Operation Two power supplies can be connected in series. Correct AC (L) +V AC (N) −V AC (L) +V AC (N) −V Note: 1. The diode is connected as shown in the figure. If the load is short-circuited, a reverse voltage will be generated inside the Power Supply. If this occurs the Power Supply may possibly deteriorate or be damaged. Always connect a diode as shown in the figure. Select a diode having the following ratings. Type Schottky Barrier diode Dielectric strength (VRRM) Twice the rated output voltage or above Twice the rated output current or above Forward current (IF) 2. Although Products having different specifications can be connected in series, the current flowing through the load must not exceed the smaller rated output current. Making Positive/Negative Outputs • The outputs are floating outputs (i.e., the primary circuits and secondary circuits are separated). You can therefore make positive and negative outputs by using two Power Supplies. You can make positive and negative outputs with any of the models. If positive and negative outputs are used, connect Power Supplies of the same model as in the following figure. (Combinations with different output capacities or output voltages can be made. However, use the lower of the two maximum rated output currents as the current to the loads.) +V +V INPUT −V Load *1 0V +V INPUT −V Load *2 −V 13 S8VK-C • Depending on the model, internal circuits may be damaged due to startup failure when the power is turned ON if loads such as a servomotor or operational amplifier may operate in series. Therefore, connect bypass diodes (D1, D2) as shown in the following figure. If the list of models that support series connection of outputs says that an external diode is not required, an external diode is also not required for positive/negative outputs. D1 +V INPUT D2 Load Load −V Load +V INPUT −V • Use the following information as a guide to the diode type, dialectic strength, and current. • Type: Schottky barrier diode • Dielectric strength (VRRM): Twice the rated Power Supply output voltage or higher • Forward current (IF): Twice the rated Power Supply output current or higher Backup Operation Backup operation can be performed with S8VK-R. Refer to the S8VK-R Datasheet for detail. In Case There Is No Output Voltage The possible cause for no output voltage may be that the overcurrent or overvoltage protection has operated. The internal protection may operate if a large amount of surge voltage such as a lightening surge occurs while turning ON the power supply. In case there is no output voltage, please check the following points before contacting us: • Checking overload protected status: Check whether the load is in overload status or is short-circuited. Remove wires to load when checking. • Checking overvoltage or internal protection: Turn the power supply OFF once, and leave it OFF for at least 3 minutes. Then turn it ON again to see if this clears the condition. Audible Noise at Power ON (240-W, and 480-W Models) A harmonic current suppression circuit is built into the Power Supply. This circuit can create noise when the input is turned ON, but it will last only until the internal circuits stabilize and does not indicate any problem in the Product. 14 Read and Understand this Catalog Please read and understand this catalog before purchasing the product. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the product in the customer's application or use of the product. Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will be used. Know and observe all prohibitions of use applicable to this product. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with your OMRON representative at any time to confirm actual specifications of purchased product. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. OMRON Corporation Industrial Automation Company Authorized Distributor: Tokyo, JAPAN Contact: www.ia.omron.com Regional Headquarters OMRON EUROPE B.V. Wegalaan 67-69-2132 JD Hoofddorp The Netherlands Tel: (31)2356-81-300/Fax: (31)2356-81-388 OMRON ELECTRONICS LLC One Commerce Drive Schaumburg, IL 60173-5302 U.S.A. Tel: (1) 847-843-7900/Fax: (1) 847-843-7787 OMRON ASIA PACIFIC PTE. LTD. No. 438A Alexandra Road # 05-05/08 (Lobby 2), Alexandra Technopark, Singapore 119967 Tel: (65) 6835-3011/Fax: (65) 6835-2711 OMRON (CHINA) CO., LTD. Room 2211, Bank of China Tower, 200 Yin Cheng Zhong Road, PuDong New Area, Shanghai, 200120, China Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200 © OMRON Corporation 2013 All Rights Reserved. In the interest of product improvement, specifications are subject to change without notice. CSM_1_2_0513 Cat. No. T058-E1-01 0313 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Omron: S82Y-VK10F