Safety Edges & Bumpers
Safety Edges
Safety Edges
(SGE & SCS Series Profiles)
• Profile materials NBR (SCS series only), EPDM or TPE
• Available in six sizes for SGE Series and two sizes for SCS Series
Description
Safety edges are used on edges of guards and gates at
possible crushing or shearing points. They are used on gates,
machines, and handling equipment to protect people and equipment. Our SGE Series safety edges use the innovative design of
co-extruded safety contact as an integral part of the safety edge.
A complete unit consists of an aluminum mounting channel, the
safety contact, and the safety edge. The special shapes of the
EPDM, TPE, or NBR rubber profiles protect the safety contact from
damage and allows actuation angles to exceed 90 degrees.
The last safety edge in a serial connection is terminated with a
resistor, which is continuously monitored by the controller. This allows the entire circuit to be monitored for shorts and wire breaks.
Aluminum
Mounting
Channel
Molded Wiring Plug
SGE Extruded Profile
with Integrated
Co-Extruded
Safety Contact
The SGE Design
SGE series profiles are patented and offer improved technical
characteristics with fewer components. Inside the safety edge
is the co-extruded switching unit, which consists of two conductive rubber extrusions inside the chamber and a high-isolating
material EPDM or TPE outer. Inside of each conductive rubber
extrusion is a copper wire with low-resistance evaluation. The
molded wiring plug at each end ensures the constant contact of
the two conductive rubber extrusions of the switching unit. The
end caps seal and protect the safety contact from dirt and water
ingression. This innovative design significantly reduces assembly
time, saving both time and money.
Important features of the SGE profile:
• Fast, accurate response even during lateral application of force
• Fewer components required for complete assembly
• Fast and easy assembly
• Integrated water drain (some models)
• Reduced weight
The SGE profile is currently available in six sizes from 8 mm
to 65 mm in height. Profiles are available with sealing lips for
applications such as doors.
Molded End Cap
with Cable Entry
and Water Drain
The SCS Design
In SCS series safety edges, the safety contact is inserted
into the switching chamber of the safety edge. The two ends
are then sealed with
Conducting
a permanently elastic
Contact Surfaces
adhesive and end
caps to keep the unit
0.24
watertight.
6
All SCS series safety
Insulating
edges are available in
Outer Sleeve
NBR only.
www.omron247.com
0.71
18
Reinforced
Copper Wire
1
Safety Edges
Safety Edges & Bumpers
Specifications
SGE-88
SGE-1510
SGE-125
SGE-225
SGE-245/
SGE-245L
SGE-365
(Black)
SGEY-365
(Yellow)
EPDM
TPE
TPE
EPDM
EPDM
EPDM
TPE
NBR
NBR
DBL Side
Tape
Integrated
Angle on
Profile or
SCA-15-9
SCA-15-9
SCA-25/25L
SCA-25/25L
SCA-35/35L
SCA-35/35L
SCA-25/25L
SCA-25/25L
68 Shore A
65 Shore A
65 Shore A
68 Shore A
68 Shore A
68 Shore A
68 Shore A
68 Shore A
68 Shore A
1.10
kg/m
1.10
kg/m
0.37
kg/m
0.48
kg/m
Material:
Mounting:
Material Hardness:
Max. Length of a
Single Safety Edge:
Weight:
0.05
kg/m
0.11
kg/m
0.18/0.20
kg/m
0.51/0.5
kg/m
0.77/0.82
kg/m
IP65
Mechanical Stability*1:
Actuation Distance:
Maximum Deformation
at 400 N:
500 N
2.1 mm
4.23 mm
7.6 mm
4.5 mm
9.4 mm
5.16 mm
5.16 mm
5.4 mm
4.1 mm
70 N with
10 mm/s
88 N with
50 mm/s
76 N
87 N
118 N
72.1 N
72.1 N
134 N
70 N
4.4 mm
4.7 mm
8.6 mm
6.7 mm
17.7 mm
33.78 mm
33.78 mm
11.8 mm
24 mm
2 x 10°
2 x 20°
2 x 30°
2 x 30°
2 x 45°
2 x 45°
2 x 45°
2 x 45°
2 x 30°
+5 to 55°C
0 to 55°C
Switching Cycles:
Switching Angle:
104
Electrical Capacity:
24 V 100 mA
Operating Temperature:
-10 to 55°C
Storage Temperature:
-25 to 75°C
Max. Series Connection
on the Safety Edges:
Inactive End Region:
SCS-2540
6.1 m
Enclosure:
Actuation Force:
SCS-2525
5 Connections
20 mm
25 mm
20 mm
40 mm
Connecting Cable:
20 mm
2 Conductors, 34 mm2
*Actuation forces and distances are tested according to EN 1760-2, Speed 200 mm/s.
*1 Maximum operating force without damaging the edge.
Specifications are subject to change without notice.
Chemical Resistance
TPE*
EPDM**
NBR***
TPE*
EPDM**
NBR***
Tear Strength (Resistance)
3
3
2
Water Resistance
1
1-2
1
Ultimate Tensile Strength
3
3
2
Diluted Acids
1
2
3
Rebound Elasticity at 20°C
2
2
Diluted Bases
1
2
2
Non-Oxidizing Acids
2
2
3
Oxidizing Acids
2
4
5
2
6
1
1-2
5
1
2
5
Features
Resistance Against Permanent
Deformation
Features
3-4
2
3
3
2
ASTM Oil #3
4-5
3
3
Vegetable Oils
Cold Flexibility
2
2
3
Organic Solvents
Heat Stability
4
2
2
Ester Solvents
2-3
2
Oxidation Stability
1
1
3
Ketone Solvents (Containing Oxygen)
2-3
3
UV Stability
1
1
3
Aliphatic Hydrocarbons (Gasoline)
5
1
Weather/Ozone Resistance
1
1
3
Aromatic Hydrocarbons
6
2-3
Flame Resistance
6
6
6
Hydrogen Hydrocarbons
6
5
Gas Permeability
3
4
2
Hydrocarbons
Abrasion
Elongation at Tear
KEY:
1 = very good
6 = insufficient
Alcohol
*TPE: Thermoplastic Elastomer
Models include: SGE-125, SGEY-365
**EPDM: Ethylene Propylene Rubber: Good resistance to ozone and
weathering. Particularly suitable for aggressive chemicals
Models include: SGE-88, SGE-1510, SGE-225, SGE-245, SGE-365
KEY:
1 = No Effects, Permanent Contact
2 = Few Effects, Some Contact
3 = Medium Effects, Some Contact
4 = Noticeable Effects, Reduced Contact
5 = Severe Effects, Very Brief Contact
6 = Extreme Effects, Avoid Contact
***NBR: Nitrile Butadiene Rubber: Good resistance to petroleum oils,
aromatic hydrocarbons, mineral oils, and vegetable oils.
Models include: SCS-2525, SCS-2540
2
www.omron247.com
2-3
5-6
1
1
5
5
Safety Edges
Safety Edges & Bumpers
Force Distance
SGE-125:
SGE-125:
Characteristic Values for Test Speed v=10 mm/s
Characteristic Values for Test Speed v=100 mm/s
Test Temperature
+20°C
Test Temperature
+20°C
Actuating Force Fa (N)
27.3
Actuating Force Fa (N)
33
Actuating Distance Sb (mm)
1.8
Actuating Distance Sb (mm)
1.9
Overtravel Distance Sv @ 250N in MM
8.3
Overtravel Distance Sv @ 250N in MM
10.1
Overtravel Distance Sv @ 400N in MM
10.6
Overtravel Distance Sv @ 400N in MM
11.1
Overtravel Distance Sv @ 600N in MM
11.5
Overtravel Distance Sv @ 600N in MM
12.2
Tested according to EN 1760-2, test unit round 80 mm, actuating point C3.
Tested according to EN 1760-2, test unit round 80 mm, actuating point C3.
SGE-225:
SGE-225:
Characteristic Values for Test Speed v=10 mm/s
Characteristic Values for Test Speed v=100 mm/s
Test Temperature
+20°C
Test Temperature
+20°C
Actuating Force Fa (N)
56.7
Actuating Force Fa (N)
62.7
Actuating Distance Sb (mm)
3.9
Actuating Distance Sb (mm)
4.4
Overtravel Distance Sv @ 250N in MM
2.3
Overtravel Distance Sv @ 250N in MM
2.7
Overtravel Distance Sv @ 400N in MM
6.7
Overtravel Distance Sv @ 400N in MM
7.2
Overtravel Distance Sv @ 600N in MM
12.0
Overtravel Distance Sv @ 600N in MM
12.0
Tested according to EN 1760-2, test unit round 80 mm, actuating point C3.
Tested according to EN 1760-2, test unit round 80 mm, actuating point C3.
SGE-245:
SGE-245:
Characteristic Values for Test Speed v=10 mm/s
Characteristic Values for Test Speed v=100 mm/s
Test Temperature
+20°C
Test Temperature
+20°C
Actuating Force Fa (N)
67.7
Actuating Force Fa (N)
Actuating Distance Sb (mm)
7.4
Actuating Distance Sb (mm)
82.7
7.8
Overtravel Distance Sv @ 250N in MM
15.8
Overtravel Distance Sv @ 250N in MM
15.2
Overtravel Distance Sv @ 400N in MM
18.3
Overtravel Distance Sv @ 400N in MM
17.7
Overtravel Distance Sv @ 600N in MM
21.7
Overtravel Distance Sv @ 600N in MM
21.9
Tested according to EN 1760-2, test unit round 80 mm, actuating point C3.
Tested according to EN 1760-2, test unit round 80 mm, actuating point C3.
SGE-365:
SGE-365:
Characteristic Values for Test Speed v=10 mm/s
Characteristic Values for Test Speed v=100 mm/s
Test Temperature
Test Temperature
+20°C
Actuating Force Fa (N)
+20°C
78.2
Actuating Force Fa (N)
107.7
Actuating Distance Sb (mm)
5.16
Actuating Distance Sb (mm)
6.23
Overtravel Distance Sv @ 250N in MM
29.82
Overtravel Distance Sv @ 250N in MM
28.37
Overtravel Distance Sv @ 400N in MM
33.78
Overtravel Distance Sv @ 400N in MM
32.76
Overtravel Distance Sv @ 600N in MM
36.51
Overtravel Distance Sv @ 600N in MM
35.34
Tested according to EN 1760-2, test unit round 80 mm, actuating point C3.
Tested according to EN 1760-2, test unit round 80 mm, actuating point C3.
www.omron247.com
3
Safety Edges
Safety Edges & Bumpers
Force Distance (continued)
SCS-2525 and SCS-2540
F (N)
525
500
SCS2
450
400
SCS
254
0
350
300
250
200
150
100
50
S (mm)
0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
SB
SV
SG
SB = Switching Distance (actuating distance)
SV = Deformation Distance (over travel distance)
SG = Total Deformation
Bending Angles and Radii
The flat aluminum mounting channel must be prepared at the
factory if it has to be bent. To order bending safety edges, please
consult OMRON Automation and Safety.
Bending Radius (mm)
Bending angles for
different assembly arrangements:
Type
Bending Angle
Type
A
B
C
SGE-88
45°
30°
30°
SGE-125
45°
20°
20°
SGE-1510
45°
20°
15°
SGE-225
45°
20°
30°
SGE-245
45°
10°
20°
SGE-245L
45°
10°
20°
SGE-365
45°
10°
15°
A
Bending Angle
Bending radii for
different assembly arrangements:
Fig. 2
Fig. 3
SGE-88
200
200
50
SGE-125
200
200
200
SGE-1510
200
200
200
SGE-225
300
400
200
SGE-245
400
500
200
SGE-365
800
800
500
Bending Angle
Bend radius based on the lower edge
of the flat aluminum mounting rail
Figure 2
Top View
B
Side View
Bending Angle
Flat Aluminum
Mounting Channel
Side View
Side View
Flat Aluminum
Mounting Channel
C
Bend radius based on the
lower edge of the profile
Figure 3
Side View
Flat Aluminum
Mounting Channel
Bending Angle
Top View
Figure 1
Notes:
By bending the safety edges, the profiles with sealing lip becomes
compressed and corrugated.
Bending angle and radii are not part of the tests complying with EN1760-2
and EN12978.
4
www.omron247.com
Bend radius based on the
middle edge of the profile
Figure 4
Fig. 4
Safety Edges
Safety Edges & Bumpers
Dimensions
(mm/in.)
Safety Edges
SGE-125
SGE-225
25
0.98
25
0.98
5.5
0.22
2.8
0.11
1.3
0.051
7
0.28
15
0.59
2.5
0.098
2.5
0.098
9
0.35
17
0.67
20
0.79
25
0.98
46
1.81
5.5
0.22
2.5
0.098
17
0.67
20
0.79
25
0.98
SGE-1510 with
“A” Aluminum Mounting
SGE-1510 with
“L” Mounting
15.5
0.61
15.5
0.61
9.1
0.36
9.1
0.36
SGE-88
8.0
0.31
16.0
0.63
(for SGE-1510 and SGE-125)
3.14SCA-15-9
0.12
8
(for SGE-1510 and SGE-125)
10)
8.00
0.31
8.00
0.31
3.14
0.12
9.0
0.35
15.0
0.59
15.0
0.59
66
2.6
9
0.35
17.6
0.693
35.2
1.386
SCS2525
13.00
SCA-25
15.00
SCA-35
(for SCS/SGE-2xxx)
(for SGE-3xxx)
13.00
0.51
15.00
0.59
9.0
0.35
25.00
0.98
14.00
0.55
25.00
0.98
35.00
1.38
SCA-25L
SCA-35L
(for SGE-3xxx)
13.00
SCA-25L
0.51
(for SCS/SGE-2xxx)
15.00
SCA-35L
0.59
(for SGE-3xxx)
25.00
0.98
25.00
0.98
14.00
0.55
14.00
0.55
15.00
0.59
3(–)
3(–)
1(+)
3-pos.
3-pos.
35.40
1.39
M8x1
12.00
0.47
M8 Male
14.00
0.55
17.91
0.70
17.91
0.70
17.91
0.70
35.00
1.38
1(+)
Overall Dimension:
14.00
0.55
35.00
1.38
M8 Female
4
M8 Male
4
14.00
0.55
14.00
0.55
17.91
0.70
www.omron247.com
43
1.692
Pin Assignment
35.00
1.38
(for SCS/SGE-2xxx)
13.00
0.51
20
0.787
Cable Connectors
0.59
14.00
0.55
SCS2540
25
0.984
(for SGE-3xxx)
0.51
15.5
0.61
25
0.984
SCA-35
(for SCS/SGE-2xxx)
10.5
0.413
2.5
0.098
7.4
0.29
SCA-15-9Fastening ProfilesSCA-25
Aluminum
8
10)
SGE/SGEY-365
SGE-245
33.90
1.33
12.00
0.47
M8 Female
5
Safety Edges
Typical Installation
APPLICATION OF 3 EDGES TO FORM 1 SYSTEM
"5" CONFIGURATION
2 Wire Lead
2 Wire Lead with Female QD
SGE365-5-0500 02000C-05000F
Safety Edge 365 Profile, 500 mm long
with two cables, one 2000 mm cable and one with 5000 mm and Female QD cable
"3" CONFIGURATION
2 Wire Lead with Male QD
2 Wire Lead with Female QD
SGE365-3-0500 05000M-02000F
Safety Edge 365 Profile, 500 mm long
with two cables, one with 5000 mm and Male QD and one 2000 mm Female QD
"4" CONFIGURATION
2 Wire Lead with Male QD
Internal Resistor
SGE365-4-1000 05000M
Safety Edge 365 Profile, 1000 mm long
with one cable, with 5000 mm and Male QD and Internal Resistor
APPLICATION OF 2 EDGES TO FORM 1 SYSTEM WITH EXTERNAL RESISTOR
"0" CONFIGURATION
2 Wire Lead
2 Wire Lead
SCS2540-0-0300 02000C-02000C
Safety Edge 2540 Profile, 300 mm long
with two cables each 2000 mm
"1" CONFIGURATION
2 Wire Lead
2 Wire Lead with Resistor
SCS2540-1-0300 02000C
Safety Edge 2540 Profile, 300 mm long
with one cable 2000 mm
and one cable 200 mm u/resistor
Wiring
Available Configurations
2 Wire Lead
2 Wire Lead
"0" CONFIGURATION
2 Wire Lead
Internal Resistor
"2" CONFIGURATION
2 Wire Lead with Male QD
2 Wire Lead with Female QD
"3" CONFIGURATION
2 Wire Lead with Male QD
Internal Resistor
"4" CONFIGURATION
2 Wire Lead
2 Wire Lead with Female QD
"5" CONFIGURATION
6
www.omron247.com
Safety Edges & Bumpers
Safety Edges
Safety Edges & Bumpers
Ordering
SGE Series
SCS Series
SGE –
–
–
–
–
Safety Edge Configuration*
88
225
25 mm x 25 mm
245
25 mm x 45 mm
Y365 35 mm x 65 mm, yellow
Wiring Configuration
0
Two 2-wire connections
1
One 2-wire connection and
one external resistor connection
2
One 2- wire connection and
one internal resistor connection
3
One quick-disconnect male and
one quick-disconnect female connector
0
Two 2-wire connections
2
One 2- wire connection and
one internal resistor connection
4
One quick-disconnect male and
one internal resistor connection
3
One quick-disconnect male and
one quick-disconnect female connector
5
One quick-disconnect female
and 2-wire connection
4
One quick-disconnect male and
one internal resistor connection
5
One quick-disconnect female
and 2-wire connection
Length
Specify length in increments of
_____ 10 mm up to 6100 mm, use 4-digits
Mounting**
Length
(blank) Standard Mounting
_____ Specify length in increments of
10 mm, from 150 mm up to 6100 mm, use 4-digits
Mounting**
(blank) Standard Mounting (all except 1510)
Angle aluminum mounting channel
(all except 1510 and 125)
L
Rubber lip mounting for ONLY SGE-1510
A
Aluminum mounting for ONLY SGE 1510
N
No mounting channel supplied
–
Wiring Configuration
35 mm x 65 mm, black
L
–
2540 25 mm x 40 mm
(Available in NBR only)
245L 25 mm x 45 mm, with Sealing Lip
365
–
2525 25 mm x 25 mm
(Available in NBR only)
1510 15 mm x 10 mm
15 mm x 25 mm
–
Safety Edge Configuration*
8 mm x 8 mm
125
SCS –
L
Angle aluminum mounting channel
N
No mounting channel supplied
First Cable Length
_____ Specify length in mm from 100 to 10,000 using 5 digits***
Second Cable Length
_____ Specify length in mm from 100 to 10,000 using 5 digits***
First Cable Length
_____ Specify length in mm from 100 to 10,000 using 5 digits***
End with “C” for wiring configurations 0, 2 or 5.
End with “M” for wiring configurations 3 or 4.
Cables exit bottom of profile, except 125 that exits on
right side looking at end.
Second Cable Length
_____ Specify length in mm from 100 to 10,000 using 5 digits***
End with “C” for wiring configuration 0.
End with “F” for wiring configurations 3 or 5.
Cables exit bottom of profile, except 125 that exits on
left side looking at end.
* Standard material for most configurations is EPDM (Exception: Standard material for the
SGE-125 and SGEY-365 are TPE; SCS-2525; and SCS-2540 are available in NBR only).
** Angle mounting channel is available for all profiles except the SGE-125 and SGE-1510
*** Examples: SGE-125-2-0150 05000C
SGE-125-3-0150 05000M-05000F
150 mm cable with Male QD = 00150M
**** For non-standard cable exit contact factory
www.omron247.com
7
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change without notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the importation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security interest in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original transportation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
14.
15.
16.
17.
18.
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for published information.
Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or settle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
Property; Confidentiality. Any intellectual property in the Products is the exclusive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law principles). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability. If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Companies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this Product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
2.
3.
4.
5.
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.55.59.01.43.00 • 01-800-226-6766 • mela@omron.com
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • mela@omron.com
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu
Authorized Distributor:
Automation Control Systems
• Machine Automation Controllers (MAC) • Programmable Controllers (PLC)
• Operator interfaces (HMI) • Distributed I/O • Software
Drives & Motion Controls
• Servo & AC Drives • Motion Controllers & Encoders
Temperature & Process Controllers
• Single and Multi-loop Controllers
Sensors & Vision
• Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors
• Amplified Photomicrosensors • Measurement Sensors
• Ultrasonic Sensors • Vision Sensors
Industrial Components
• RFID/Code Readers • Relays • Pushbuttons & Indicators
• Limit and Basic Switches • Timers • Counters • Metering Devices
• Power Supplies
Safety
• Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety
Controllers • Light Curtains • Safety Relays • Safety Interlock Switches
F52I-E-02
09/18
Note: Specifications are subject to change.
Printed on recycled paper.
© 2018 Omron Electronics LLC
Printed in U.S.A.