V4KF-01JF-001

MTA-B-03027 D (1/14) Hardware Specifications of V4KF-*** Series Hybrid Manual Insertion Card Reader Rev. A Rev. A1 Rev. A2 Rev. A3 Rev. B Rev. B1 Rev. B2 Rev. C Rev. D June 25, 2004 July 24, 2004 July 29, 2004 Nov 02, 2004 Feb 10, 2005 Feb 24, 2005 May 20, 2005 July 05, 2006 Dec 14, 2006 RoHS Compliant ©Hitachi-Omron Terminal Solutions, Corp. All Rights Reserved. 2004-2007 MTA-B-03027 D (2/14) Table of Contents Abstract Reference Standards Definition of Terminology Applicable Module Name Specifications 5.1 Mechanical Specification 5.2 Magnetic card function 5.3 ICC function 5.4 SAM 5.5 Shutter function 5.6 Lock function 5.7 Power Requirement 5.8 Electrical interface 5.9 Software interface 5.10 LED Indicator 5.11 Diagnostics function 6. Environmental Condition 7. General performance 8. Life 9. Response to Regulated Chemical Substances 10. Outline drawing 11. Appendix A 1. 2. 3. 4. 5. 4 4 5 6 6 6 6 7 7 7 8 8 8 9 9 9 9 10 10 10 11 14 MTA-B-03027 D (3/14) [Specification History of Modification] Rev Draft Draft2 Date Dec 12, 2003 Feb 27, 2004 A June 10, 2004 A1 July 24, 2004 A2 July 29, 2004 Page ALL Page 4, 6 Page 8 Page 9 Page 9 Page 9 Page 6 Page 7 Page 8 ALL Page 4 Page 4 Page 7 Page 7 Content The draft version is created. Remove the standard ISO/IEC 7811-3 Add the signal HDRST 2 2 Correction the unit from mm/s to m/s Correct the document number of the data transmission specification. Correct the low temperature from 5℃ to 0℃. Correct the supported card type to ISO/IEC 7810/ID-1. Correct the description of the IC function and SAM. Correct the Pin No.10 in Power supply connector from HDREST to NC. Correct from ISO to ISO/IEC Correct ISO/IEC 7810 from 1995-08-15 to 2003-11-01. A3 B B1 B2 Nov 02, 2004 Feb 10, 2005 Feb 25, 2005 May 20, 2005 Page 1, 7 Page 6, 7, 13 Page 11, 12 Page 6 Page 7 Page 8 Page 9 C July 05,2006 Front page Delete ENV1375-1: 1994 Add SLE4418 in Support ICC of Synchronous card. Correct the standard of “Support SAM chip” in 5.4 SAM from ENV1375 to ISO/IEC7810. The company name is changed Add 5SAM Version (V4KF-01JS-002). Correction of drawing Modify Drawing from “Mounting” to “Outline” in 5.1 [3]. Add 7.1412MHz in CLK of 5.3 [2] 4) Add the SAM deactivation in 5.7 [5] 2). Add the SAM in description of 5.9 [5] and 5.11 Indication of ‘RoHS Compliant’ D Dec 14,2006 Page 10 Added Chapter 9 “Chapter No.” is changed after “Chapter 9”. MTA-B-03027 D (4/14) 1. Abstract This document provides the hardware specifications of Hybrid Manual Insertion Card Reader of V4KF-*** Series with RS232 interface. This equipment can read the data of Magnetic Card, and read/write the data of IC card. 2. Reference Standards [1] ISO/IEC 7810: 2003-11-01 Identification cards - Physical characteristics [2] ISO/IEC 7811-1:2002, ISO/IEC 7811-2, 6:2001 Identification cards -- Recording technique [3] ISO/IEC 7816-1:1998 Identification cards -- Integrated circuit(s) cards with contacts Part 1: Physical characteristics [4] ISO/IEC 7816-2:1999 Identification cards -- Integrated circuit(s) cards with contacts Part 2: Dimensions and location of contacts [5] ISO/IEC 7816-3:1997 Identification cards -- Integrated circuit(s) cards with contacts Part 3: Electronic signals and transmission protocols [6] ISO/IEC 7816-4: 1995 Identification cards -- Integrated circuit(s) cards with contacts Part 4: Inter-industry commands for interchange [7] ISO/IEC 7816-4: 1995/Amd 1:1997 Secure messaging on the structures of APDU messages [8] EMV2000 Integrated Circuit Card Specification for Payment Systems Book 1 Application Independent ICC to Terminal Interface Requirements Version 4.0 December, 2000 MTA-B-03027 D (5/14) 3. Definition of Terminology LED Light-Emitting Diode PCB Printed-Circuit Board S1 Positioning Sensor of Insertion slot S2 Positioning Sensor of Rear End S3 Sensor to detect the lock/release of Lock blade ICC Integrated Circuit Card SAM Secure Application Module C/R Card Reader ATR Answer to Reset Etu Elementary Time Unit Vpp Voltage at VPP Vcc Voltage at VCC Host HOST Terminal APDU Application Protocol Data Unit FW Firmware LED Insert PCB ICC contact S3 S1 LOCK Mag. Head S2 MTA-B-03027 D (6/14) 4. Applicable Module Name No 1 2 3 Module Name V4KF-01JS-001 V4KF-01JF-001 V4KF-01JS-002 *1 *2 R Y Magnetic card read Track 1 Track 2 Track 3 R*1 R R R R R R R R ICC controller Y*2 Y Y SAM 1SAM 1SAM 5SAM Bezel Round Type Flat Type Round Type : Magnetic reading function : 8 contacts for C1 to C8 are provided. 5. Specifications 5.1 Mechanical Specification [1] External dimensions (See Outline Drawing) Width V4KF-01JS-001 80.0mm V4KF-01JF-001 101.6mm V4KF-01JS-002 80.0mm *1 Including connector’s lock Height Length 50.0mm 76.2mm 50.0mm 133.0mm (147.0 mm *1) 133.0mm (147.0 mm *1) 134.5mm (147.0 mm *1) [2] Weight Less than 250g [3] Mounting (See Outline Drawing) (1) In case of using the Mounting Hole (V4KF-01JS-001, V4KF-01JF-001, V4KF-01JS-002) 1) Screw M3 2) Quantity 4 pieces 3) Torque Less than 0.79N･m Design the mounting bases to keep the difference within +/-0.2mm in height among four mounting holes (refer to Outline drawing about location of these holes) (2) In case of using the Screw Hole of Bezel (V4KF-01JF-001) 1) Screw M4 2) Quantity 4 pieces 3) Torque Less than 1.30N･m Select the screw in order to keep the meshing length 4.0mm or less. [4] Card position detection Two photo sensors (S1, S2) are provided in order to detect the card. The state of these sensors can be retrieved by the command and response. 5.2 Magnetic card function [1] Magnetic card type [2] Reading function [3] Reading direction [4] Card speed In conformity to ISO/IEC 7810/ID-1, ISO/IEC 7811-1/2/6 Read specified tracks simultaneously. Bi-directional capability (insert/pull out) 100-1000 mm/s capability (at flat card) MTA-B-03027 D (7/14) 5.3 ICC function [1] Number and location of contacts on ICC Number and location of contacts on ICC are specified in ISO/IEC 7816-2 figure 2. [2] Applicable ICC (1) Asynchronous card 1) Support ICC In conformity to ISO/IEC 7816-1/2/3(Default), EMV4.0 Level1 2) Protocol T=0 and T=1 (Automatic protocol type selection via ATR detection is possible.) 3) Data byte reading/writing Inverse convention (MSB first, negative logic) and direct convention (LSB first, positive logic) are available. 4) Clock during/after ATR *1 3.5712 MHz (F=372) (Default) / 7.1428 MHz (F=744) (Conform to ISO / IEC 7816-3) 5) Communication speed 1etu = (F/D) x 1/f sec D=1: (Default) / 2, 4: (Changeable by PPS) 6) Vpp Not connected 7) Vcc 5V / 3V (Type A and Type B) (Automatic selection via T=15 of ATR detection is possible.) 8) EMV Approval EMV4.0 Level 1 Approved (11757 0504 400 20 FIM) (2) Synchronous card 1) Support ICC In conformity to ISO/IEC 7816-1/2/10, SLE4442/4432/4428/4418 2) Vcc 5V 3) Vpp Not connected *1 Answer To Reset HITACHI-OMRON TERMINAL SOLUTIONS asks customers to check the performance of ICC with HITACHI-OMRON TERMINAL SOLUTIONS standard ICC controller and FW in advance, if ICC is special card. Because ISO standard and ICC(s) are subject to frequent modification. HITACHI-OMRON TERMINAL SOLUTIONS supports you for capability of performing customer’s ICC, provided with ICC and its specification. 5.4 SAM [1] The following SAM controller is equipped with shipment. 1 SAM socket is mounted on the Main PCB. And the additional 4 SAM socket are mounted on the additional PCB in V4KF-01JS-002 only. - 1SAM : V4KF-01JS-001, V4KF-01JF-001 - 5SAM : V4KF-01JF-002 [2] SAM specification 1) Support SAM chip 2) Protocol 3) Data byte reading/writing 4) Clock during/after ATR *1 5) Communication speed 6) Vpp 7) Vcc In conformity to ISO/IEC 7810(ID000), ISO/IEC 7816-1/2/3 T=0 and T=1 (Automatic protocol type selection via ATR detection is possible.) Inverse convention (MSB first, negative logic) and direct convention (LSB first, positive logic) are available. 3.5712 MHz(Conform to ISO / IEC 7816-3) 6 1etu = (372/D) x 1/(3.5712 x 10 ) sec D=1: (Default) / 2, 4: (Changeable by PPS) Not connected 5V/3V (Automatic selection via T=15 of ATR detection is possible.) 5.5 Shutter function [1] This shutter is equipped on the insertion slot of the C/R. It opens automatically by inserting the card. It prevents foreign objects like dusts and coins from intruding to inside. [2] This shutter should open by inserting the card that is more than 53.92mm in width. MTA-B-03027 D (8/14) 5.6 Lock function [1] Pin type lock mechanism is equipped to hold the card during operation of ICC in response to command from host. [2] This lock mechanism can be controlled by the command from the host. [3] The condition of this lock mechanism can be checked by the command and response. [4] This lock mechanism is released automatically at the power failure. [5] This Lock mechanism works under the below conditions (1) The card is inserted completely. (2) The card does not exist inside of C/R. 5.7 Power Requirement [1] Power supply voltage 10.8 – 13.2V DC (including ripple) [2] Ripple of power supply 100mV (p-p) or less [3] Power consumption (Input voltage: 12V DC) In operation magnetic card 500mA or less IC card 1.5A or less In Standby 300mA or less [4] Power supply connector HIF3BD-10PA-254DS02 (2.54mm pitch HIROSE Japan) or equivalent (MIL-C-83503) is mounted on C/R’s PCB. Pin assignment of C/R (in/out direction view from the reader) Pin No. 1 2 3 4 5 6 7 8 9 10 Assigned signal TXD RXD DTR CTS SG 12V GND 12V GND NC IN/OUT OUT IN OUT IN - Function Transmit DATA Receive DATA DATA Terminal Ready Clear to Send 0V Power Ground Power Ground Not Connect (Cable with connector for Power supply and RS232 interface is not included) [5] Power failure 1) Detection Voltage Less than 10.8V DC 2) Power failure process In case of power failure, C/R deactivates the ICC and SAM chip(s), and releases the Lock. 5.8 Electrical interface [1] Interface specification (1) Electronic Interface (2) Transmission Speed (3) Synchronous Method (4) Communication Method (5) Pin Assignment RS232 interface 1200, 2400, 4800, 9600, 19200, 38400 bps Start-Stop synchronization Method Half-duplex Method Refer to the table in 5.7 Power Requirement MTA-B-03027 D (9/14) 5.9 Software Interface [1] Transmission protocols [2] Port to host [3] Format [4] Downloadable [5] Module V4KF Series Card Reader Data Transmission Specification (Document No. MTA-H-04015). Handling with a magnetic card, an IC card and SAM via single port A common APDU format is used for handling various ICC and SAM All software are supported to be downloaded. Firmware is independently divided into every functional module (e.g. ICC handling module, SAM handling module, etc) and every module can be independently downloaded (regardless of order of download) respectively. 5.10 LED Indicator [1] One LED is equipped to inform the state of C/R and the reading result of the magnetic data. [2] This LED can be indicated the three colors (green, red and orange). [3] The specification of LED indicator can be controlled by the command from the host. In detail, refer to V4KF Series Card Reader Data Transmission Specification (Document No. MTA-H-04015). 5.11 Diagnostics function [1] C/R provides the following functions as diagnostics of each module in the C/R. This function is performed by pressing the white button located on the top of C/R just near SAM socket. The test card is required to perform diagnostics. This function reports the following. *1 (1) OK/NG for Sensor Level (2) OK/NG for Magnetic card reading (3) OK/NG for LOCK mechanism (4) OK/NG for ICC function The SAM function is not worked. [2] C/R indicates the result of the diagnostics by using LED indicator. *1 *1 In detail, V4KF Series Card Reader Data Transmission Specification (Document No.MTA-H-04015). Make sure not to press this button, when the system is in operation. 6. Environmental Condition [1] Temperature (1) In operation (2) In storage [2] Humidity (1) In operation (2) In storage 0 to 55 ℃ -25 ℃ for 16 hours to 70 ℃ for 72 hours for non operation and transport 5 to 85% RH, no condensation and absolute air humidity of 23 3 g/m or less 5 to 90% RH, no condensation and absolute air humidity of 40 3 g/m or less 7. General performance [1] Insulation Resistance [2] Dielectric Strength [3] Durable Vibration [4] Shock Endurance 20MΩor more at 100V DC (At normal temperature and humidity) 500V AC for 1minute Frequency 10-150 Hz Single vibration width 0.10mm 2 Acceleration 15m/s Direction X,Y,Z 2 Acceleration 150m/s Direction X,Y,Z MTA-B-03027 D (10/14) 8. Life [1] Card Reader life [2] Magnetic head life *1 [3] IC contact unit life *2 800,000 passes or 5 years, whichever comes earlier. 1,000,000 passes (minimum) 300,000 operations (Contact unit should be replaced every 300,000 operations.) *1 One pass denotes forward and backward movement. *2 One operation denotes the movement of fully insertion and extraction. 9. Response to Regulated Chemical Substances [1] Response to RoHS: Conformed with RoHS Directive(2002/95/EC) "The restriction of the use of certain hazardous substances in electrical and electronic equipment". (Notice) In case the equipment mounting this card reader will be shipped to People's Republic of China,please consult our sales representatives. MTA-B-03027 D (11/14) 10. Outline drawing (1) V4KF-01JS-001 Dimensions in millimeters MTA-B-03027 D (12/14) (2) V4KF-01JF-001 Dimensions in millimeters MTA-B-03027 D (13/14) (3) V4KF-01JS-002 Dimensions in millimeters MTA-B-03027 D (14/14) 11. Appendix A Abstract from ISO/IEC 7816-2: 1999 (E) 4. Number and locations of the contacts This part of ISO/IEC 7816 defines eight contacts referred to as C1 to C8. The contacts are located as shown in figure 2. The contacts shall be located on the front of the card. The dimensions are referenced to the left and upper edges of the front surface of the end. Dimensions in millimeters Figure 2. Contacts location