WT30-FT011

FA Wireless SS Terminals WT30 Construct a Wireless System for ON/OFF Data Collection That Is Ideal for Monitoring Production Site Equipment • Wireless Slave Station equipped with I/O. • Height of 90 mm and DIN Rail mounting enables installation in control panels. • Easily check wireless communications status from indicator display. • I/O Slave Stations can also be used as Slave Stations in WD30 systems. • Conforms to radio wave standards for Japan, China (pending), USA, and Europe. Ordering Information ■ List of Models Wireless Unit model Type Specifications/No. of I/O points WT30-M01-FLK Serial master RS-232C WT30-SID16 I/O slaves 16 DC inputs (NPN/PNP) WT30-SMD16 8 DC inputs (NPN/PNP) + 8 transistor outputs (NPN) WT30-SMD16-1 8 DC inputs (NPN/PNP) + 8 transistor outputs (PNP) Note: An Antenna and Mounting Brackets are not included with the Wireless SS Terminal. ■ Accessories Antennas Applicable Standards Model Type WT30-AT001 Magnet-base Antenna (2 antennas per set) WT30-AT002 Flat Diversity Antenna (1 antenna) WT30-AT003 Pencil Antenna (2 antennas per set) Communications Cables Model Length XW2Z-0100U-3 1m XW2Z-0200U-3 2m XW2Z-0500U-3 5m XW2Z-0200U-5 2m XW2Z-0500U-5 5m Conformity to Safety Standards Application For personal computer Always use a Class 2 power supply to conform to UL standards. Main Class 2 Power Supplies OMRON Switching Power Supplies Cross cable for PLC • S8VS (15 W, 30 W, 60 W type) • S82K (15 W, 30 W, 50 W, 90 W type) Conformity to EN Standards Other Model • FCC part 15.247 (USA) • EN 300 440-2 (Europe) • ARIB STD-T66 (Japan) • (China) (approval pending) Type WT30-FT001 DIN Rail Mounting Bracket (for TH35-7.5) WT30-FT002 DIN Rail Mounting Bracket (for TH35-15) WT30-FT003 Surface Mounting Bracket (screw-mounting) (2 brackets per set) WT30-FT011 Flat Diversity Antenna Mounting Brackets (with magnets) WT30-CA2M Antenna Extension Cable (1 cable, 2 m) Use a DC power line less than 3 m to conform to EN standards. If a power line of 3 m or longer is required, extend the length at the Switching Power Supply’s primary side (i.e., the AC power line). Applicable Countries Wireless standards have been met for the following countries. The product cannot be used in any other countries. Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungry, Iceland, Ireland, Italy, Japan, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, UK, USA FA Wireless SS Terminals WT30 1 Specifications ■ Ratings Item WT30-M01-FLK Serial Master WT30-SID16/SMD16/SMD16-1 I/O Slaves Power supply (wireless communications power supply) Rated voltage 24 V DC Allowable voltage range 20.4 to 26.4 V DC Power consumption 3 W max. (See note 1.) Error output/output power supply (for output circuits) Rated voltage --- 24 V DC Allowable voltage range --- 20.4 to 26.4 V DC Insulation resistance 20 MΩ min. (at 100 V DC) between the power 20 MΩ min. (at 100 V DC) between the power supply and chassis supply and all I/O and I/O power supply and between the power supply and chassis Dielectric strength 1,500 V AC for 1 min between power supply and chassis Noise immunity IEC61000-4-4. 1 kV (power supply line) Vibration resistance (See note 2.) JIS C0040 Frequency: 10 to 55 Hz; Amplitude of 0.35 mm or acceleration of 50 m/s2, whichever is smaller (DIN Rail mounting: single amplitude of 0.1 mm or acceleration of 15 m/s2) 10 sweeps of 8 min each (i.e., 80 min in total) in X, Y, Z directions Shock resistance Conforms to JIS C0041: 300 m/s2 3 times each in X, Y, and Z directions Ambient operating temperature −10 to 55°C (with no condensation or icing) Number of simultaneously ON I/O points (with the Terminal mounted with the dust-proof 10 max.: −10 to 55°C (with no condensation or label facing up) icing) 16 max.: −10 to 50°C (with no condensation or icing) (with the Terminal mounted with the dust-proof label facing up) Ambient operating humidity 25% to 85% (with no condensation or icing) Ambient environment No corrosive gases Storage temperature −25 to 65°C (with no condensation or icing) Protective structure 1,500 V AC for 1 min between the power supply and all I/O and I/O power supply and between the power supply and chassis IP20 Terminal construction Power supply and I/O Screwless terminal block (Phoenix Contact FFKDS/V1-5.08 or equivalent) --D-sub, 9-pin (female) Inch screws (OMRON XM2F-0910-132 or equivalent), Master station only Serial Safety standards UL: UL508 (Listing) Weight 330 g max. Note: 1. Provide a power supply of at least 15 W, considering the inrush current generated at startup. 2. Use the WT30-FT003 Surface Mounting Bracket when installing the WT30 in environments subject to vibration. ■ Wireless Interface Specifications Item Specifications Wave type Spread Spectrum (direct sequence; DS-SS) Communication method Simplex Frequency band 2,401 to 2,480.2 MHz Number of channels 67 channels (based on switching) Transmitter output power 10 mW/MHz Baud rate between wireless stations 100 kbps Communications distance (See note.) Indoors: 60 m min. (approx. 50 m min. with Magnet-base Antennas and Flat Diversity Antennas) Outdoors: Approx. 300 m min. (anticipated distances) (without using relay stations) Error detection method CRC-CCITT (16 bits) Relay functions One stage using I/O slave for the serial master configuration. Number of stations per area (See note.) 10 sets max. (recommended) Number of I/O Slaves connected 64 max. Note: Varies according to the installation environment. ■ Package Contents • WT30 FA Wireless SS Terminal • Terminal labels (I/O Slaves only) • Instruction Sheet • Adhesive non-slip feet (Serial Master only) 2 FA Wireless SS Terminals WT30 Nomenclature ■ Serial Master Station ■ Unit No. Switch Set the unit number of the Serial Master Station Unit No. switch Set the unit number of the Serial Master Station. Node setting switch (WNODE) Set the number of connected I/O Slave Stations. Channel setting switch (WCH) Set the communications frequency channel. Antenna terminal (ANT1) Antenna terminal (ANT2) Default: 00 ■ Node Setting Switch (WNODE) Set the number of connected I/O Slave Stations. Set the node number of the Slave Stations being used as I/O Slave Stations. The Slave Station functions as a relay station when the node number is set to 99. Default: 01 Status indicators Received signal strength indicator Special function switch ■ Channel Setting Switch (WCH) Set the communications frequency. Default: 02 ■ Function Setting Switch Serial Master Station No. Mode selection switch Switch between RUN, TEST, and SET mode. Function setting switch Make the detailed settings for RUN/TEST/SET mode. Power supply terminal Supply power to the WT30. 1 RS-232C Terminal Connect the PLC, personal computer, etc. Serial communications setting switch Set the baud rate. I/O terminal status indicators (0 to 7 or 8 to 15) The contact status is displayed. Channel setting switch (WCH) Set the communications frequency. Antenna terminal (ANT1) Antenna terminal (ANT2) OFF functions Clears I/O status data when a communications error occurs. Enable scan list Disable scan list 3 Relays used Relays not used TEST mode Signal strength monitor Signal strength monitor disabled enabled All channels Specified channels automatically switched 6 7 SET mode --- --- Scan list recognition Nothing done 8 Registers specified I/O Registers all I/O slaves slave automatically 9 Recognizes serial numbers Ignores serial numbers --- --- 10 Not used I/O Slave Station Status indicators Received signal strength indicator No. 1 I/O terminals Connect the contact signals. Power supply terminal Supply power to the WT30 and output circuits. Applicable mode RUN mode Holds I/O status data when a communications error occurs. OFF functions Clears I/O status data when a communications error occurs. Input hold Normal mode 3 Input filter: 100 ms Input filter: 10 ms TEST mode Signal strength monitor Signal strength monitor disabled enabled 5 All channels Specified channels automatically switched 6 Installation test function Nothing done --- --- Special function switch Function setting switch Make the detailed settings for RUN/TEST mode. ON functions 2 4 Mode selection switch Switch between RUN, TEST, and SET mode. RUN mode Holds I/O status data when a communications error occurs. 5 Node setting switch (WNODE) Set the unit number of the I/O Slave Station. ON functions 2 4 ■ I/O Slave Station Applicable mode 7 to 10 Not used FA Wireless SS Terminals WT30 3 ■ Serial Communications Setting Switch No. 1 2 3 4 Function ON Communications setting Detailed selection settings (settings for No. 2 to 8 used) 1 Baud rate (bps) (See note.) 2 Total value = 0: 1,200 4 = 1: 2,400 = 2: 4,800 = 3: 9,600 = 4: 19,200 = 5: 38,400 = 6: 57,600 = 7: 115,200 OFF Default settings (baud rate: 9,600 bps; data length: 7 bits; parity: even; stop bits: 2) Settings for No. 2 to 8 are ignored. 0 Data length 8 bits 7 bits 6 Parity None Yes Odd Even 1 bit 2 bits 8 Stop bits Indicator Color Status PWR Green Lit ERR (Slave Station) Red Meaning (primary error) Power is being supplied. Not lit Power is not being supplied. Lit Error output is ON: Wireless device error or wireless communications error. (See note) Not lit No wireless device error or wireless communications error. 0 0 5 7 ■ Display COMM Yellow Lit (Master Station) Not lit Serial communications in progress. No serial communications. 0 to 15 (Slave Station) Yellow Lit/Not lit ON/OFF status for input or output signals RSSI Lit/ Receiving Signal Strength Red/ Yellow/ All not lit Indicator monitor: Number of indicators lit (receiving signal Green strength 1 to 9) Receiving signal strength less than 0 to 1. MS Green Lit Communications are normal. (Module Status) Flashing TEST mode or SET mode has been activated. Red Lit Note: For example, if pins number 2, 3, and 4 are all ON, the total is 7, which corresponds to a baud rate of 115,200 bps. A fatal error has occurred that cannot be recovered from. Replace the Unit Flashing A non-fatal error has occurred that can be recovered from by resetting the system. --WS (Wireless Status) Not lit Green Lit Power is not being supplied or the system is resetting. The station has joined the wireless network. Flashing Permission to join wireless network received from Serial Master Station (Slave Station) Red Lit A fatal error has occurred that cannot be recovered from. Flashing Error from which recovery is possible --- Not lit Wireless communications are not in progress. Note: When using the WD30 as the Serial Master Station, the ERR indicator will light if normal I/O communications are not possible due to an error in the host network. 4 FA Wireless SS Terminals WT30 Wiring ■ Serial Master Station (WT30-M01-FLK) D-sub, 9-pin, Female End at WT30 RS-232C Connector 54321 Power supply terminal Supply power to the Unit WT30 9876 Pin No. Signal I/O direction 1 --- --- 2 RD Output 3 SD Input 4 --- --- 5 SG --- 6 --- --- 7 --- --- 8 --- --- 9 --- --- I/O Characteristics ■ I/O Slave Station WT30-SID16 Error output (PNP) Inputs IN V G 24 V DC 0 V 0 8 Power supply 1 9 2 10 3 11 COM COM 4 12 IN Inputs 5 13 6 14 7 15 COM ERRP COM ERRN Error output (NPN) Inputs WT30-SMD16 WT30-SMD-16-1 Error output/output power supply Inputs Error output (PNP) Inputs IN V G 24 V DC 0 V 0 0 Power supply 1 1 2 2 Outputs 3 3 COM 4 COM 4 OUT 5 5 6 6 Outputs Input Characteristics Inputs 7 7 COM ERRP Output/Error Output Characteristics Error output power supply Item Specifications Input voltage 24 V DC Allowable voltage range 20.4 to 26.4 V DC Input impedance 4.7 kΩ (typical) Input current 5 mA (typical) ON voltage/ 17.4 V DC, 3.0 mA min. current characteristics OFF voltage/ 5.0 V DC, 1.0 mA max. current characteristics Input filter 10 ms/100 ms (Selected using switch.) Input voltage 24 V DC Allowable voltage 20.4 to 26.4 V DC Max. switching current 100 mA max. per output (at 20.4 to 26.4 V DC) Simultaneous usage of error output NPN/PNP is not possible. Leakage current 0.1 mA max. Residual voltage 1.0 V max. Fuse One for every two outputs except for error output circuits, which have one for every NPN/ PNP output. (No fuses can be replaced by the user.) COM ERRN Error output (NPN) FA Wireless SS Terminals WT30 5 Input Circuit Diagram Output Circuit Diagram (NPN) V OUT 0 Secondary internal circuit Secondary internal circuit IN 0 IN 1 IN 2 OUT 1 Fuse OUT 2 Fuse IN 15 OUT 7 COM (IN) Fuse Error Output Circuit Diagram Output Circuit Diagram (PNP) Fuse Fuse V OUT 0 Secondary internal circuit Secondary internal circuit V Fuse G ERRP ERRN OUT 1 Fuse OUT 2 OUT 3 G OUT 7 G Dimensions Note: All units are in millimeters unless otherwise indicated. Serial Master Station I/O Slave Station WT30-M01-FLK WT30-SID16 WT30-SMD16 WT30-SMD16-1 13.3 105 105 13.3 120 ia. (15) ur, 5d Fo 90 60 40 (15) Surface mounting bracket WT30-FT003 6 FA Wireless SS Terminals WT30 DIN rail mounting bracket WT30-FT001 or WT30-FT002 7.3 With Magnet-base Antenna With Flat Diversity Antenna WT30-AT001 WT30-AT002 With Pencil Antenna WT30-AT003 40 150 (46) (23) (34) (46) R50 R38 20 R40 (32) 4.6 (38) Serial Master Station Surface Mounting Bracket WT30-FT003 I/O Slave Station I/O Slave Station DIN Rail mounting bracket WT30-FT001 or WT30-FT002 DIN Rail mounting bracket WT30-FT001 or WT30-FT002 Magnet-base Antenna Flat Diversity Antenna Pencil Antenna WT30-AT001 WT30-AT002 WT30-AT003 57.5 26 Three, 3 dia. 57.5 52 75 115 10.5 dia. 10.5 dia. 2010 2010 35.8 dia. 39 DIN Rail Mounting Bracket Surface Mounting Bracket Flat Diversity Antenna Mounting Brackets (with magnets) WT30-FT001 WT30-FT002 WT30-FT003 WT30-FT011 FA Wireless SS Terminals WT30 7 ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. N139-E1-01 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company Industrial Devices and Components Division H.Q. Wireless Components Department Shiokoji Horikawa, Shimogyo-ku, Kyoto, 600-8530 Japan Tel: (81)75-344-7116/Fax: (81)75-344-7189 Printed in Japan 0105