6N137SVM

8-Pin DIP High-Speed 10 MBit/s Logic Gate Optocouplers Single-Channel: 6N137M, HCPL2601M, HCPL2611M Dual-Channel: HCPL2630M, HCPL2631M Description The 6N137M, HCPL2601M, HCPL2611M single−channel and HCPL2630M, HCPL2631M dual−channel optocouplers consist of a 850 nm AlGaAs LED, optically coupled to a very high speed integrated photo−detector logic gate with a strobable output. This output features an open collector, thereby permitting wired OR outputs. The switching parameters are guaranteed over the temperature range of −40°C to +85°C. A maximum input signal of 5 mA will provide a minimum output sink current of 13 mA (fan out of 8). An internal noise shield provides superior common mode rejection of typically 10 kV/ms. The HCPL2601M and HCPL2631M has a minimum CMR of 5 kV/ms. The HCPL2611M has a minimum CMR of 10 kV/ms. www.onsemi.com PDIP8 6.6x3.81, 2.54P CASE 646BW 8 1 PDIP8 9.655x6.6, 2.54P CASE 646CQ 8 1 PDIP8 GW CASE 709AC 8 1 Features • • • • • • • • Very High Speed – 10 MBit/s Superior CMR – 10 kV/ms Fan−out of 8 Over −40°C to +85°C Logic Gate Output Strobable Output Wired OR−open Collector Safety and Regulatory Approvals ♦ UL1577, 5,000 VACRMS for 1 Minute ♦ DIN EN/IEC60747−5−5 These are Pb−Free Devices 1 MARKING DIAGRAM ON 6N137 VXXYYB 6N137 V Applications • • • • • • • Ground Loop Elimination LSTTL to TTL, LSTTL or 5 V CMOS Line Receiver, Data Transmission Data Multiplexing Switching Power Supplies Pulse Transformer Replacement Computer−peripheral Interface © Semiconductor Components Industries, LLC, 2009 June, 2021 − Rev. 2 PDIP8 GW CASE 709AD 8 XX YY B = Device Number = DIN EN/IEC60747−5−5 Option (only appears on component ordered with this option) = Two−Digit Year Code, e.g., ‘16’ = Two−Digit Work Week, Ranging from ‘01’ to ‘53’ = Assembly Package Code ORDERING INFORMATION See detailed ordering and shipping information on page 14 of this data sheet. 1 Publication Order Number: HCPL2631M/D Single−Channel: 6N137M, HCPL2601M, HCPL2611M Dual−Channel: HCPL2630M, HCPL2631M SCHEMATICS 8 VCC N/C 1 + 1 8 VCC VF1 + 2 7 VE _ 2 6 VO _ 7 V01 VF _ 3 3 6 V02 VF2 N/C 4 + 4 5 GND 6N137M, HCPL2601M, HCPL2611M 5 GND HCPL2630M, HCPL2631M A 0.1 mF bypass capacitor must be connected between pins 8 and 5 (Note 1). Figure 1. Schematics TRUTH TABLE (Positive Logic) Input Enable Output H H L L H H H L H L L H H NC L L NC H www.onsemi.com 2 Single−Channel: 6N137M, HCPL2601M, HCPL2611M Dual−Channel: HCPL2630M, HCPL2631M SAFETY AND INSULATION RATINGS (As per DIN EN/IEC 60747−5−5, this optocoupler is suitable for “safe electrical insulation” only within the safety limit data. Compliance with the safety ratings shall be ensured by means of protective circuits.) Characteristics Parameter Installation Classifications per DIN VDE 0110/1.89 Table 1, For Rated Mains Voltage Climatic Classification