74ABT2244
Octal Buffer/Line Driver with 25Ω Series Resistors
in the Outputs
tm
Features
General Description
■ Guaranteed latchup protection
The ABT2244 is an octal buffer and line driver designed
to drive the capacitive inputs of MOS memory drivers,
address drivers, clock drivers, and bus-oriented transmitters/receivers.
■ High-impedance, glitch-free bus loading during entire
power up and power down cycle
■ Nondestructive, hot-insertion capability
The 25Ω series resistors in the outputs reduce ringing
and eliminate the need for external resistors.
Ordering Information
Package
Number
Package Description
74ABT2244CSC
M20B
20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300" Wide
74ABT2244CSJ
M20D
20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
Order Number
74ABT2244CMSA
MSA20
20-Lead Shrink Small Outline Package (SSOP), JEDEC MO-150, 5.3mm Wide
74ABT2244CMTC
MTC20
20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153,
4.4mm Wide
Devices are also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering number.
Pb-Free package per JEDEC J-STD-020B.
Connection Diagram
Schematic of Each Output
Pin Descriptions
Pin Names
OE1, OE2
I0–I7
O0–O7
Description
Output Enable Input (Active LOW)
Truth Table
OE1
I0–3
O0–3
OE2
I4–7
O4–7
Inputs
H
X
Z
H
X
Z
Outputs
L
H
H
L
H
H
L
L
L
L
L
L
H = HIGH Voltage Level X = Immaterial
L = LOW Voltage Level
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
Z = High Impedance
www.fairchildsemi.com
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
March 2007
Symbol
TSTG
Parameter
Rating
Storage Temperature
–65°C to +150°C
TA
Ambient Temperature Under Bias
–55°C to +125°C
TJ
Junction Temperature Under Bias
–55°C to +150°C
VCC
VCC Pin Potential to Ground Pin
–0.5V to +7.0V
VIN
Input Voltage(1)
–0.5V to +7.0V
IIN
Input Current(1)
–30mA to +5.0mA
VO
Voltage Applied to Any Output
Disabled or Power-off State
–0.5V to 5.5V
HIGH State
–0.5V to VCC
Current Applied to Output in LOW State (Max.)
twice the rated IOL (mA)
DC Latchup Source Current (Across Comm Operating Range)
–300mA
Over Voltage Latchup (I/O)
10V
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to absolute maximum ratings.
Symbol
TA
VCC
∆V / ∆t
Parameter
Rating
Free Air Ambient Temperature
–40°C to +85°C
Supply Voltage
+4.5V to +5.5V
Minimum Input Edge Rate
Data Input
50mV/ns
Enable Input
20mV/ns
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
www.fairchildsemi.com
2
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
Absolute Maximum Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Symbol
Parameter
VCC
Conditions
Min.
VIH
Input HIGH Voltage
Recognized HIGH Signal
VIL
Input LOW Voltage
Recognized LOW Signal
VCD
Input Clamp Diode Voltage
Min.
IIN = –18mA
VOH
Output HIGH
Min.
IOH = –3mA
2.5
IOH = –32mA
2.0
Typ.
Max. Units
2.0
V
0.8
V
–1.2
V
V
VOL
Output LOW Voltage
Min.
IOL = 15mA
0.8
V
IIH
Input HIGH Current
Max.
VIN = 2.7V(3)
1
µA
VIN = VCC
1
IBVI
Input HIGH Current Breakdown
Test
Max.
VIN = 7.0V
7
µA
Input LOW Current
Max.
VIN = 0.5V(3)
–1
µA
VIN = 0.0V
–1
IIL
VID
Input Leakage Test
IOZH
Output Leakage Current
0.0
IID = 1.9µA, All Other Pins
Grounded
475
0–5.5V VOUT = 2.7V; OEn = 2.0V
10
VOUT = 0.5V; OEn = 2.0V
IOZL
IOS
Output Short-Circuit Current
Max.
VOUT = 0.0V
ICEX
Output HIGH Leakage Current
Max.
V
µA
–10
–275
mA
VOUT = VCC
50
µA
VOUT = 5.5V, All Others GND
100
µA
All Outputs HIGH
50
µA
ICCL
All Outputs LOW
30
mA
ICCZ
Power Supply Current
Max.
OEn = VCC, All Others at VCC
or GND
50
µA
ICCT
Additional
ICC/Input
Max.
IZZ
ICCH
ICCD
Bus Drainage Test
Power Supply Current
0.0
Max.
–100
VI = VCC – 2.1V
2.5
mA
Outputs 3-STATE
Enable Input VI = VCC – 2.1V
2.5
mA
Outputs 3-STATE
Data Input VI = VCC – 2.1V,
All Others at VCC or GND
50
µA
Outputs OPEN, OEn = GND(2),
One-Bit Toggling,
50% Duty Cycle
0.1
mA/
MHz
Outputs Enabled
Dynamic ICC No Load(3)
Max.
Notes:
1. Either voltage limit or current limit is sufficient to protect inputs.
2. For 8-bit toggling, ICCD < 0.8mA/MHz.
3. Guaranteed, but not tested.
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
www.fairchildsemi.com
3
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
DC Electrical Characteristics
SOIC and SSOP packages.
TA = +25°C,
VCC = +5V,
CL = 50pF
Min.
Typ.
Max.
Min.
Max.
Units
Propagation Delay,
Data to Outputs
1.0
2.2
3.9
1.0
3.9
ns
1.0
2.9
4.4
1.0
4.4
Output Enable Time
1.5
3.7
6.0
1.5
6.0
2.1
4.3
7.0
2.1
7.0
1.7
3.5
5.8
1.7
5.8
1.7
3.7
5.8
1.7
5.8
Symbol
tPLH
tPHL
tPZH
Parameter
tPZL
tPHZ
TA = –40°C to +85°C,
VCC = 4.5V–5.5V,
CL = 50pF
Output Disable Time
tPLZ
ns
ns
Capacitance
Symbol
Parameter
Conditions
(TA = 25°C)
Typ.
Units
CIN
Input Capacitance
VCC = 0V
5.0
pF
COUT(4)
Output Capacitance
VCC = 5.0V
9.0
pF
Note:
4. COUT is measured at frequency f = 1MHz, per MIL-STD-883, Method 3012.
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
www.fairchildsemi.com
4
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
AC Electrical Characteristics
*Includes jig and probe capacitance
Figure 2. Test Input Signal Levels
Figure 1. Standard AC Test Load
Amplitude
Rep. Rate
tw
tr
tf
3.0V
1MHz
500ns
2.5ns
2.5ns
Figure 3. Test Input Signal Requirements
AC Waveforms
Figure 4. Propagation Delay Waveforms for
Inverting and Non-Inverting Functions
Figure 5. 3-STATE Output HIGH and LOW Enable
and Disable Times
Figure 6. Propagation Delay, Pulse Width Waveforms
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
Figure 7. Setup Time, Hold Time
and Recovery Time Waveforms
www.fairchildsemi.com
5
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
AC Loading
Dimensions are in inches (millimeters) unless otherwise noted.
Figure 8. 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300" Wide
Package Number M20B
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
www.fairchildsemi.com
6
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
Physical Dimensions
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
Physical Dimensions (Continued)
Dimensions are in millimeters unless otherwise noted.
Figure 9. 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
Package Number M20D
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
www.fairchildsemi.com
7
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
Physical Dimensions (Continued)
Dimensions are in millimeters unless otherwise noted.
Figure 10. 20-Lead Shrink Small Outline Package (SSOP), JEDEC MO-150, 5.3mm Wide
Package Number MSA20
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
www.fairchildsemi.com
8
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
Physical Dimensions (Continued)
Dimensions are in millimeters unless otherwise noted.
Figure 11. 20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Package Number MTC20
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
www.fairchildsemi.com
9
®
ACEx
Across the board. Around the world.¥
ActiveArray¥
Bottomless¥
Build it Now¥
CoolFET¥
CROSSVOLT¥
CTL™
Current Transfer Logic™
DOME¥
2
E CMOS¥
®
EcoSPARK
EnSigna¥
FACT Quiet Series™
®
FACT
®
FAST
FASTr¥
FPS¥
®
FRFET
GlobalOptoisolator¥
GTO¥
HiSeC¥
i-Lo¥
ImpliedDisconnect¥
IntelliMAX¥
ISOPLANAR¥
MICROCOUPLER¥
MicroPak¥
MICROWIRE¥
MSX¥
MSXPro¥
OCX¥
OCXPro¥
®
OPTOLOGIC
®
OPTOPLANAR
PACMAN¥
POP¥
®
Power220
®
Power247
PowerEdge¥
PowerSaver¥
®
PowerTrench
Programmable Active Droop¥
®
QFET
QS¥
QT Optoelectronics¥
Quiet Series¥
RapidConfigure¥
RapidConnect¥
ScalarPump¥
SMART START¥
®
SPM
STEALTH™
SuperFET¥
SuperSOT¥-3
SuperSOT¥-6
SuperSOT¥-8
SyncFET™
TCM¥
®
The Power Franchise
®
TinyLogic
TINYOPTO¥
TinyPower¥
TinyWire¥
TruTranslation¥
PSerDes¥
®
UHC
UniFET¥
VCX¥
Wire¥
™
TinyBoost¥
TinyBuck¥
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS
HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE
APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER
ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S
WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body or
(b) support or sustain life, and (c) whose failure to perform
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to
result in a significant injury of the user.
2. A critical component in any component of a life support,
device, or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Advance Information
Formative or In Design
This datasheet contains the design specifications for product
development. Specifications may change in any manner without notice.
Definition
Preliminary
First Production
This datasheet contains preliminary data; supplementary data will be
published at a later date. Fairchild Semiconductor reserves the right to
make changes at any time without notice to improve design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild Semiconductor
reserves the right to make changes at any time without notice to improve
design.
Obsolete
Not In Production
This datasheet contains specifications on a product that has been
discontinued by Fairchild Semiconductor. The datasheet is printed for
reference information only.
Rev. I24
©1992 Fairchild Semiconductor Corporation
74ABT2244 Rev. 1.4
www.fairchildsemi.com
10
74ABT2244 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an
exhaustive list of all such trademarks.