74ACT14SC

DATA SHEET www.onsemi.com Hex Inverter with Schmitt Trigger Input 1 74AC14, 74ACT14 SOIC14 CASE 751EF 14 General Description The 74AC14 and 74ACT14 contain six inverter gates each with a Schmitt trigger input. They are capable of transforming slowly changing input signals into sharply defined, jitter−free output signals. In addition, they have a greater noise margin than conventional inverters. The 74AC14 and 74ACT14 have hysteresis between the positive−going and negative−going input thresholds (typically 1.0 V) which is determined internally by transistor ratios and is essentially insensitive to temperature and supply voltage variations. 1 TSSOP−14 WB CASE 948G 14 1 TSSOP−14 WB CASE 948G−01 14 1 Features • • • • SOIC−14 NB CASE 751A−03 14 ICC Reduced by 50% Outputs Source/Sink 24 mA 74ACT14 has TTL−Compatible Inputs These are Pb−Free Devices MARKING DIAGRAM 14 AC(T)14 AWLYWW ABSOLUTE MAXIMUM RATINGS Parameter Supply Voltage Symbol Value Unit VCC −0.5 to +7.0 V DC Input Diode Current VI = −0.5 V VI = VCC + 1.5 V IIK DC Input Voltage VI DC Output Diode Current VO = −0.5 V VO = VCC + 0.5 V IOK DC Output Voltage VO −0.5 to VCC + 0.5 V DC Output Source or Sink Current IO ±50 mA ICC or IGND ±50 mA Storage Temperature TSTG −65 to +150 °C Junction Temperature TJ 140 °C DC VCC or Ground Current per Output Pin mA −20 +20 −0.5 to VCC + 1.5 V mA −20 +20 1 AC14, ACT14 A WL Y WW = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week MARKING DIAGRAM 14 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. AC(T) 14 ALYWG G 1 AC14, ACT14 A L Y W G = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information on page 2 of this data sheet. © Semiconductor Components Industries, LLC, 1988 December, 2021 − Rev. 3 1 Publication Order Number: 74AC14/D 74AC14, 74ACT14 ORDERING INFORMATION Order Number Package Number 74AC14SC M14A 74AC14MTC MTC14 74ACT14SC M14A 74ACT14MTC MTC14 NOTE: Package Description 14−Lead Small Outline Integrated Circuit (SOIC), JEDEC MS−012, 0.150” Narrow 14−Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO−153, 4.4 mm Wide 14−Lead Small Outline Integrated Circuit (SOIC), JEDEC MS−012, 0.150” Narrow 14−Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO−153, 4.4 mm Wide Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering number. IEEE/IEC Figure 2. Logic Symbol Figure 1. Connection Diagram PIN DESCRIPTION Pin Description An Inputs On Outputs FUNCTION TABLE Input Output A O L H H L RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage AC ACT Min Max 2.0 4.5 6.0 5.5 Unit V VI Input Voltage 0 VCC V VO Output Voltage 0 VCC V TA Operating Temperature −40 +85 °C Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. www.onsemi.com 2 74AC14, 74ACT14 DC ELECTRICAL CHARACTERISTICS FOR AC TA = +255C Symbol VOH VOL IIN (Note 3) Vt+ Vt− VH(MAX) VH(MIN) Parameter Minimum HIGH Level Output Voltage Maximum LOW Level Output Voltage VCC(V) 3.0 Conditions IOUT = −50 mA Typ TA = −405C to +855C Guaranteed Limits 2.99 2.9 2.9 4.5 4.49 4.4 4.4 5.5 5.49 5.4 5.4 3.0 IOH = 12 mA − 2.56 2.46 4.5 IOH = 24 mA − 3.86 3.76 5.5 IOH = 24 mA (Note 1) − 4.86 4.76 3.0 IOUT = 50 mA 0.002 0.1 0.1 4.5 0.001 0.1 0.1 5.5 0.001 0.1 0.1 Unit V V 3.0 IOL = 12 mA − 0.36 0.44 4.5 IOL = 24 mA − 0.36 0.44 5.5 IOL = 24 mA (Note 1) − 0.36 0.44 Maximum Input Leakage Current 5.5 VI = VCC, GND − ±0.1 ±1.0 mA Maximum Positive Threshold 3.0 TA = Worst Case − 2.2 2.2 V 4.5 − 3.2 3.2 5.5 − 3.9 3.9 − 0.5 0.5 4.5 − 0.9 0.9 5.5 − 1.1 1.1 Minimum Negative Threshold Maximum Hysteresis Minimum Hysteresis 3.0 3.0 TA = Worst Case TA = Worst Case − 1.2 1.2 4.5 − 1.4 1.4 5.5 − 1.6 1.6 − 0.3 0.3 4.5 − 0.4 0.4 5.5 − 0.5 0.5 3.0 TA = Worst Case V V V IOLD Minimum Dynamic 5.5 VOLD = 1.65 V Max. − − 75 mA IOHD Output Current (Note 2) 5.5 VOHD = 3.85 V Min. − − −75 mA Maximum Quiescent Supply Current 5.5 VIN = VCC or GND − 2.0 20.0 mA ICC (Note 3) 1. All outputs loaded; thresholds on input associated with output under test. 2. Maximum test duration 2.0 ms, one output loaded at a time. 3. IIN and ICC at 3.0 V are guaranteed to be less than or equal to the respective limit at 5.5 V VCC. www.onsemi.com 3 74AC14, 74ACT14 DC ELECTRICAL CHARACTERISTICS FOR ACT TA = +255C Symbol VIH VIL VOH VOL IIN VH(MAX) Parameter VCC(V) Minimum HIGH Level Input Voltage 4.5 Maximum LOW Level Input Voltage 4.5 Minimum HIGH Level Output Voltage 4.5 Maximum LOW Level Output Voltage 5.5 5.5 Conditions 1.5 2.0 2.0 1.5 2.0 2.0 VOUT = 0.1 V or VCC − 0.1 V 1.5 0.8 0.8 1.5 0.8 0.8 IOUT = −50 mA 4.49 4.34 4.4 5.49 5.4 5.4 5.5 4.5 VIN = VIL or VIH, IOH = −24 mA − 3.86 3.76 5.5 VIN = VIL or VIH, IOH = −24 mA (Note 4) − 4.86 4.76 4.5 IOUT = 50 mA 0.001 0.1 0.1 5.5 Unit V V V V 0.001 0.1 0.1 4.5 VIN = VIL or VIH, IOL = 24 mA − 0.36 0.44 5.5 VIN = VIL or VIH, IOL = 24 mA (Note 4) − 0.36 0.44 Maximum Input Leakage Current 5.5 VI = VCC, GND − ±0.1 ±1.0 mA Maximum Hysteresis 4.5 TA = Worst Case − 1.4 1.4 V − 1.6 1.6 − 0.4 0.4 − 0.5 0.5 − 2.0 2.0 − 2.0 2.0 − 0.8 0.8 − 0.8 0.8 0.6 − 1.5 mA Minimum Hysteresis 4.5 TA = Worst Case 5.5 Vt+ TA = −405C to +855C Guaranteed Limits VOUT = 0.1 V or VCC − 0.1 V 5.5 VH(MIN) Typ Maximum Positive Threshold 4.5 Minimum Negative Threshold 4.5 ICCT Maximum ICC/Input 5.5 VI = VCC − 2.1 V IOLD Minimum Dynamic Output Current (Note 5) 5.5 VOLD = 1.65 V Max. − − 75 mA 5.5 VOHD = 3.85 V Min. − − −75 mA Maximum Quiescent Supply Current 5.5 VIN = VCC or GND − 2.0 20.0 mA Vt− IOHD ICC TA = Worst Case V 5.5 TA = Worst Case 5.5 4. All outputs loaded; thresholds on input associated with output under test. 5. Maximum test duration 2.0 ms, one output loaded at a time. www.onsemi.com 4 V V 74AC14, 74ACT14 AC ELECTRICAL CHARACTERISTICS FOR AC TA = +25°C, CL = 50 pF Symbol tPLH tPHL Parameter TA = −40°C to +85°C, CL = 50 pF VCC(V) (Note 6) Min Typ Max Min Max Unit 3.3 1.5 9.5 13.5 1.5 15.0 ns 5.0 1.5 7.0 10.0 1.5 11.0 3.3 1.5 7.5 11.5 1.5 13.0 5.0 1.5 6.0 8.5 1.5 9.5 Propagation Delay Propagation Delay ns 6. Voltage range 3.3 is 3.3 V + 0.3 V. Voltage range 5.0 is 5.0 V + 0.5 V. AC ELECTRICAL CHARACTERISTICS FOR ACT TA = +25°C, CL = 50 pF Symbol Parameter TA = −40°C to +85°C, CL = 50 pF VCC(V) (Note 7) Min Typ Max Min Max Unit tPLH Propagation Delay 5.0 3.0 8.0 10.0 3.0 11.0 ns tPLH Propagation Delay 5.0 3.0 8.0 10.0 3.0 11.0 ns 7. Voltage range 5.0 is 5.0 V + 0.5 V. CAPACITANCE Symbol Parameter Conditions CIN Input Capacitance VCC = OPEN CPD Power Dissipation Capacitance AC ACT VCC = 5.0 V www.onsemi.com 5 Typ Unit 4.5 pF 25.0 80 pF MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SOIC−14 NB CASE 751A−03 ISSUE L 14 1 SCALE 1:1 D DATE 03 FEB 2016 A B 14 8 A3 E H L 1 0.25 B M DETAIL A 7 13X M b 0.25 M C A S B S 0.10 X 45 _ M A1 e DETAIL A h A C SEATING PLANE DIM A A1 A3 b D E e H h L M MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.19 0.25 0.35 0.49 8.55 8.75 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ INCHES MIN MAX 0.054 0.068 0.004 0.010 0.008 0.010 0.014 0.019 0.337 0.344 0.150 0.157 0.050 BSC 0.228 0.244 0.010 0.019 0.016 0.049 0_ 7_ GENERIC MARKING DIAGRAM* SOLDERING FOOTPRINT* 6.50 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF AT MAXIMUM MATERIAL CONDITION. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSIONS. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 14 14X 1.18 XXXXXXXXXG AWLYWW 1 1 1.27 PITCH XXXXX A WL Y WW G = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “G”, may or may not be present. Some products may not follow the Generic Marking. 14X 0.58 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. STYLES ON PAGE 2 DOCUMENT NUMBER: DESCRIPTION: 98ASB42565B SOIC−14 NB Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 2 onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com SOIC−14 CASE 751A−03 ISSUE L DATE 03 FEB 2016 STYLE 1: PIN 1. COMMON CATHODE 2. ANODE/CATHODE 3. ANODE/CATHODE 4. NO CONNECTION 5. ANODE/CATHODE 6. NO CONNECTION 7. ANODE/CATHODE 8. ANODE/CATHODE 9. ANODE/CATHODE 10. NO CONNECTION 11. ANODE/CATHODE 12. ANODE/CATHODE 13. NO CONNECTION 14. COMMON ANODE STYLE 2: CANCELLED STYLE 3: PIN 1. NO CONNECTION 2. ANODE 3. ANODE 4. NO CONNECTION 5. ANODE 6. NO CONNECTION 7. ANODE 8. ANODE 9. ANODE 10. NO CONNECTION 11. ANODE 12. ANODE 13. NO CONNECTION 14. COMMON CATHODE STYLE 4: PIN 1. NO CONNECTION 2. CATHODE 3. CATHODE 4. NO CONNECTION 5. CATHODE 6. NO CONNECTION 7. CATHODE 8. CATHODE 9. CATHODE 10. NO CONNECTION 11. CATHODE 12. CATHODE 13. NO CONNECTION 14. COMMON ANODE STYLE 5: PIN 1. COMMON CATHODE 2. ANODE/CATHODE 3. ANODE/CATHODE 4. ANODE/CATHODE 5. ANODE/CATHODE 6. NO CONNECTION 7. COMMON ANODE 8. COMMON CATHODE 9. ANODE/CATHODE 10. ANODE/CATHODE 11. ANODE/CATHODE 12. ANODE/CATHODE 13. NO CONNECTION 14. COMMON ANODE STYLE 6: PIN 1. CATHODE 2. CATHODE 3. CATHODE 4. CATHODE 5. CATHODE 6. CATHODE 7. CATHODE 8. ANODE 9. ANODE 10. ANODE 11. ANODE 12. ANODE 13. ANODE 14. ANODE STYLE 7: PIN 1. ANODE/CATHODE 2. COMMON ANODE 3. COMMON CATHODE 4. ANODE/CATHODE 5. ANODE/CATHODE 6. ANODE/CATHODE 7. ANODE/CATHODE 8. ANODE/CATHODE 9. ANODE/CATHODE 10. ANODE/CATHODE 11. COMMON CATHODE 12. COMMON ANODE 13. ANODE/CATHODE 14. ANODE/CATHODE STYLE 8: PIN 1. COMMON CATHODE 2. ANODE/CATHODE 3. ANODE/CATHODE 4. NO CONNECTION 5. ANODE/CATHODE 6. ANODE/CATHODE 7. COMMON ANODE 8. COMMON ANODE 9. ANODE/CATHODE 10. ANODE/CATHODE 11. NO CONNECTION 12. ANODE/CATHODE 13. ANODE/CATHODE 14. COMMON CATHODE DOCUMENT NUMBER: DESCRIPTION: 98ASB42565B SOIC−14 NB Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 2 OF 2 onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SOIC14 CASE 751EF ISSUE O DOCUMENT NUMBER: DESCRIPTION: 98AON13739G SOIC14 DATE 30 SEP 2016 Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS TSSOP−14 WB CASE 948G ISSUE C 14 DATE 17 FEB 2016 1 SCALE 2:1 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S N 2X 14 L/2 0.25 (0.010) 8 M B −U− L PIN 1 IDENT. N F 7 1 0.15 (0.006) T U NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. S DETAIL E K A −V− K1 J J1 ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ SECTION N−N −W− C 0.10 (0.004) −T− SEATING PLANE H G D DETAIL E DIM A B C D F G H J J1 K K1 L M MILLIMETERS INCHES MIN MAX MIN MAX 4.90 5.10 0.193 0.200 4.30 4.50 0.169 0.177 −−− 1.20 −−− 0.047 0.05 0.15 0.002 0.006 0.50 0.75 0.020 0.030 0.65 BSC 0.026 BSC 0.50 0.60 0.020 0.024 0.09 0.20 0.004 0.008 0.09 0.16 0.004 0.006 0.19 0.30 0.007 0.012 0.19 0.25 0.007 0.010 6.40 BSC 0.252 BSC 0_ 8_ 0_ 8_ GENERIC MARKING DIAGRAM* 14 SOLDERING FOOTPRINT XXXX XXXX ALYWG G 7.06 1 1 0.65 PITCH 14X 0.36 14X 1.26 DIMENSIONS: MILLIMETERS DOCUMENT NUMBER: 98ASH70246A DESCRIPTION: TSSOP−14 WB A L Y W G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “G”, may or may not be present. Some products may not follow the Generic Marking. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS TSSOP−14 WB CASE 948G ISSUE C 14 DATE 17 FEB 2016 1 SCALE 2:1 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S N 2X 14 L/2 0.25 (0.010) 8 M B −U− L PIN 1 IDENT. N F 7 1 0.15 (0.006) T U NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. S DETAIL E K A −V− K1 J J1 ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ SECTION N−N −W− C 0.10 (0.004) −T− SEATING PLANE H G D DETAIL E DIM A B C D F G H J J1 K K1 L M MILLIMETERS INCHES MIN MAX MIN MAX 4.90 5.10 0.193 0.200 4.30 4.50 0.169 0.177 −−− 1.20 −−− 0.047 0.05 0.15 0.002 0.006 0.50 0.75 0.020 0.030 0.65 BSC 0.026 BSC 0.50 0.60 0.020 0.024 0.09 0.20 0.004 0.008 0.09 0.16 0.004 0.006 0.19 0.30 0.007 0.012 0.19 0.25 0.007 0.010 6.40 BSC 0.252 BSC 0_ 8_ 0_ 8_ GENERIC MARKING DIAGRAM* 14 SOLDERING FOOTPRINT XXXX XXXX ALYWG G 7.06 1 1 0.65 PITCH 14X 0.36 14X 1.26 DIMENSIONS: MILLIMETERS DOCUMENT NUMBER: 98ASH70246A DESCRIPTION: TSSOP−14 WB A L Y W G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “G”, may or may not be present. Some products may not follow the Generic Marking. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative