ASM809,ASM8091,ASM810
July 2005
rev 1.8
3-Pin Microcontroller Power Supply Supervisor
General Description
Six voltage thresholds are available to support 3V to 5V
systems:
The ASM809/ASM8091/ASM810 are cost effective 3.0V, 3.3V
RESET THRESHOLD
and 5.0V power supply supervisor circuits optimized for lowpower microprocessor (µP), microcontroller (µC) and digital
systems. They provide a reset output during power-up, powerdown and brown-out conditions. They provide excellent
reliability by eliminating external components and adjustments.
The
ASM809/ASM8091/ASM810
are
improved
drop-in
replacements for the Maxim MAX809/810 and feature 60%
lower supply current.
A reset signal is issued if the power supply voltage drops below
a preset reset threshold and is asserted for at least 140mS after
the supply has risen above the reset threshold. The ASM809/
ASM8091 has an active-low RESET output that is guaranteed
Suffix
Voltage (V)
L
4.63
M
4.38
J
4.00
T
3.08
S
2.93
R
2.63
Features:
to be in the correct logic state for VCC down to 1.1V. The
ASM810 has an active-high RESET output. The reset
•
Monitor 5V, 3.3V and 3V supplies
comparator is designed to ignore fast transients on VCC.
•
140mS minimum reset pulse width
•
Active-low reset valid with 1.1V supply (ASM809/
ASM8091)
Low supply current makes the ASM809/ASM8091/ASM810
ideal for use in portable and battery operated equipment. The
•
Small 3&5-pin SOT-23 Packages
ASM809/ASM8091/ASM810 are available in a compact,
•
No external components
industry standard 3&5-pin SOT-23 Packages.
•
Specified over full temperature range - -40°C to 105°C
Applications
Typical Operating Circuit
•
Embedded controllers
•
Portable/Battery operated systems
•
Intelligent instruments
•
Wireless communication systems
•
PDAs and handheld equipments
•
Computers
VCC
VCC
ASM809
ASM8091
(ASM810)
RESET
(RESET)
GND
VCC
µP
RESET (RESET)
Input
GND
Alliance Semiconductor
2575 Augustine Drive . Santa Clara, CA 95054 . Tel: 408.855.4900 . Fax: 408.855.4999 . www.alsc.com
Notice: The information in this document is subject to change without notice
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Pin Diagram
3-SOT23
GND
1
RESET
ASM809
(ASM810)
(RESET) RESET
Block Diagram
5-SOT23
3 VCC
2
VCC
1
5 NC
+
-
2 ASM8091
GND 3
+
-
VCC
4 NC
RESET Generator
4.63V
4.38V
4.00V
3.08V
2.93V
2.63V
RESET
(RESET)
ASM809/8091
(ASM810)
GND
Pin Description
Pin #
Pin
Name
ASM8091
5-SOT 23
ASM809
3-SOT 23
ASM810
3
1
-
GND
1
2
-
RESET
-
-
2
RESET
2
3
-
VCC
Function
Ground.
RESET is asserted LOW if VCC falls below VTH and remains LOW for
atleast 140mS (TRST) after VCC exceeds the threshold.
RESET is asserted HIGH if VCC falls below VTH and remains HIGH for
atleast 140mS (TRST) after VCC exceeds the threshold.
Power supply input voltage (3.0V, 3.3V, 5.0V).
Detailed Description
A
proper
reset
input
enables
a
microprocessor
/
VCC
microcontroller to start in a known state. ASM809/ASM8091/
5V
VTH
0V
ASM810 assert reset to prevent code execution errors during
power-up, power-down and brown-out conditions.
RESET
5V
0V
RESET
5V
0V
Reset Timing
The reset signal is asserted LOW for the ASM809,ASM8091
TRST
ASM809
ASM8091
ASM810
and HIGH for the ASM810 when the VCC supply voltage falls
below the threshold trip voltage and remains asserted for
140mS minimum after the VCC has risen above the
Figure 1: Reset TIming Diagram
threshold.
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
2 of 12
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Application Information
Bidirectional Reset Pin Interfacing
The ASM809/ASM8091/ASM810 can interface with µP / µC
Negative VCC Transients
The ASM809/ASM8091/ASM810 protect µpS from brownouts
and low VCC. Short duration transients of 100mV amplitude
and 60µpS or less duration typically do not cause a false
bi-directional reset pins by connecting a 4.7kΩ resistor in
series with the ASM809/ASM8091/ASM810 reset output and
the µP/µC bi-directional reset pin.
RESET.
BUF
Valid Reset with VCC under 1.1V
When VCC is under 1.1V, to ensure logic inputs connected to
Buffered
RESET
VCC
the ASM809,ASM8091 RESET pin are in a known state, a
100kΩ pull-down resistor is needed at RESET. The value of
the resistor is not critical. A 100kΩ pull-up resistor to VCC at
RESET is needed with the ASM810.
Power supply
ASM809
ASM8091
RESET
VCC
Power Supply
µC or µP
4.7kΩ
RESET
Input
GND
GND
Bi-directional I/O Pin
ASM809
ASM8091
Figure 4: Bidirectional Reset Pin Interfacing
RESET
100kΩ
GND
Figure 2: RESET valid with VCC under 1.1V
VCC
100kΩ
Power Supply
ASM810
RESET
GND
Figure 3: RESET valid with VCC under 1.1V
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
3 of 12
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Absolute Maximum Ratings Table 1:
Parameter
Min
Max
Units
VCC
-0.3
6.0
V
RESET, RESET
-0.3
VCC + 0.3
V
Input current at VCC
20
mA
Output current: RESET, RESET
20
mA
Rate of Rise at VCC
100
V/µs
2
200
KV
V
Pin Terminal Voltage With Respect To Ground
ESD rating
HBM
MM
Note: These are stress ratings only and the functional operation is not implied. Exposure
to absolute maximum ratings for prolonged time periods may affect device reliability.
Absolute Maximum Ratings Table 2:
Parameter
Min
Power Dissipation (TA = 70°C)
Max
Units
320
mW
Operating temperature range
-40
105
°C
Storage temperature range
-65
160
°C
300
°C
Lead temperature (Soldering, 10 sec)
Note: These are stress ratings only and the functional operation is not implied. Exposure to absolute
maximum ratings for prolonged time periods may affect device reliability.
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
4 of 12
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Electrical Characteristics:
Unless otherwise noted, VCC is over the full voltage range, TA = -40°C to 105°C.
Typical values at TA = 25°C, VCC = 5V for L/M/J devices, VCC = 3.3V for T/S devices and VCC = 3V for R devices.
Symbol
VCC
ICC
Parameter
Input Voltage
Range
Supply Current
Conditions
TA = 0°C to 70°C
TA= -40°C to 85°C
VCC < 5.5V
TA = -40°C to 85°C
VCC < 3.6V
TA = 85°C to 105°C
VCC < 5.5V
TA = 85°C to 105°C
VCC < 3.6V
TA = 25°C
TA = -40°C to 85°C
TA = 85°C to 105°C
TA = 25°C
M devices
TA = -40°C to 85°C
TA = 85°C to 105°C
TA = 25°C
J devices
VTH
TA = -40°C to 85°C
TA = 85°C to 105°C
Reset Threshold
TA = 25°C
T devices
TA = -40°C to 85°C
TA = 85°C to 105°C
TA = 25°C
S devices
TA = -40°C to 85°C
TA = 85°C to 105°C
TA = 25°C
R devices
TA = -40°C to 85°C
TA = 85°C to 105°C
9
6.0
Delay
Max
Unit
5.5
5.5
V
V
15
10
25
20
µA
4.56
4.50
4.40
4.63
4.70
4.75
4.86
4.31
4.25
4.16
4.38
4.45
4.50
4.56
3.93
3.89
3.80
4.00
4.06
4.10
4.20
3.04
3.00
2.92
3.08
3.11
3.15
3.23
2.89
2.85
2.78
2.93
2.96
3.00
3.08
2.59
2.55
2.50
2.63
2.66
2.70
2.76
V
Reset Threshold
Temp Coefficient
VCC to Reset
Typ
1.1
1.2
TA = -40°C to 105°C
L devices
Min
VCC = VTH to VTH-100mV
30
ppm/°C
20
µs
Notes:
1. Production testing done at TA = 25°C. Over-temperature specifications guaranteed by design only, using six sigma design limits.
2. RESET output is active LOW for the ASM809/ASM8091 and RESET output is active HIGH for the ASM810.
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
5 of 12
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Symbol
Parameter
Conditions
Min
Typ
Max
TA = -40°C to 85°C
140
240
560
TA = 85°C to 105°C
100
Unit
TRST
Reset Active
Timeout Period
ASM8091S
VOL
Low RESET
Output Voltage
ASM809/
ASM8091
High RESET
Output Voltage
ASM809/
ASM8091
VCC > VTH max., ISOURCE = 500µA, ASM809R/S/T
Low RESET
Output Voltage
ASM810
VCC= VTH max., ISINK = 1.2mA, ASM810R/S/T
0.3
V
VOL
VCC= VTH max., ISINK = 3.2mA, ASM810L/M/J
0.4
V
VOH
High RESET
Output Voltage
ASM810
VOH
VCC= VTH min., ISINK = 1.2mA, ASM809R/S/T and
840
0.3
0.4
VCC= VTH min., ISINK = 3.2mA, ASM809L/M/J
0.8VCC
and ASM8091S
1.8V < VCC < VTH min., ISOURCE = 150µA
V
0.3
VCC > 1.1V, ISINK = 50µA
VCC > VTH max., ISOURCE = 800µA, ASM809L/M/J
ms
V
VCC - 1.5
0.8VCC
V
Notes:
1. Production testing done at TA = 25°C. Over-temperature specifications guaranteed by design only, using six sigma design limits.
2. RESET output is active LOW for the ASM809/ASM8091 and RESET output is active HIGH for the ASM810.
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
6 of 12
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Typical Operating Characteristics
Unless otherwise noted, VCC is over the full voltage range, TA = -40°C to 105°C. Typical values at TA = 25°C, VCC = 5V for L/M/J devices, VCC = 3.3V
for T/S devices and VCC = 3V for R devices.
Supply Current Vs. Temperature
Supply Current (µA)
ASM809T
ASM809R
Temperature (°C)
Normalized Reset Threshold
Normalized Reset Threshold Vs. Temperature
ASM809T
ASM809R
Temperature (°C)
Power-up Reset Timeout Period (ms)
Power-up Reset Timeout Period Vs. Temperature
ASM809T
ASM809R
Temperature (°C)
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
7 of 12
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Package Dimensions
Plastic SOT-23 (3-Pin)
Inches
Min
Millimeters
Max
Min
Max
Plastic SOT-23 (3-Pin)
A
0.030
0.046
0.75
1.17
A1
0.002
0.006
0.05
0.15
B
0.012
0.020
0.30
0.50
C
0.003
0.008
0.08
0.20
D
0.110
0.120
2.80
3.04
E
0.047
0.055
1.20
1.40
e
0.037 BSC
0.95 BSC
e1
0.075 BSC
1.9 BSC
H
0.083
0.104
2.10
2.64
L
0.016
0.024
0.40
0.60
a
o
o
o
o
8
S
0
8
NA
0
NA
D
B
E
H
e
S
A
a
A1
e1
C
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
L
8 of 12
July 2005
ASM809,ASM8091,ASM810
rev 1.8
5L SOT- 23 Package
1.
2.
3.
4.
5.
6.
NOTE:
DIMENSIONS ARE IN MM.
DRAWING NOT TO SCALE.
DIMENSIONS ARE INCLUSIVE OF PLATING.
DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR.
MOLD FLASH SHALL NOT EXCEED 0.254MM.
JEDEC PACKAGE REFERENCE IS MO-193.
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
9 of 12
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Ordering Information:
Part Number
Reset Threshold (V)
Temperature Range
Pin-Package
Package Marking
(LL Lot Code)
ASM809 ACTIVE LOW RESET, TIN-LEAD PLATED DEVICES
ASM809LEUR
4.63
-40°C to +105°C
3-SOT23
SALL
ASM809MEUR
4.38
-40°C to +105°C
3-SOT23
SBLL
ASM809JEUR
4.00
-40°C to +105°C
3-SOT23
SCLL
ASM809TEUR
3.08
-40°C to +105°C
3-SOT23
SDLL
ASM809SEUR
2.93
-40°C to +105°C
3-SOT23
SELL
ASM809REUR
2.63
-40°C to +105°C
3-SOT23
SFLL
ASM8091SEUK
2.93
-40°C to +105°C
5-SOT23
LO83
ASM809 ACTIVE LOW RESET, LEAD FREE DEVICES
ASM809LEURF
4.63
-40°C to +105°C
3-SOT23
NALL
ASM809MEURF
4.38
-40°C to +105°C
3-SOT23
NBLL
ASM809JEURF
4.00
-40°C to +105°C
3-SOT23
NCLL
ASM809TEURF
3.08
-40°C to +105°C
3-SOT23
NDLL
ASM809SEURF
2.93
-40°C to +105°C
3-SOT23
NELL
ASM809REURF
2.63
-40°C to +105°C
3-SOT23
NFLL
ASM8091SEUKF
2.93
-40°C to +105°C
5-SOT23
LO83
ASM810 ACTIVE HIGH RESET, TIN-LEAD PLATED DEVICES
ASM810LEUR
4.63
-40°C to +105°C
3-SOT23
SGLL
ASM810MEUR
4.38
-40°C to +105°C
3-SOT23
SHLL
ASM810JEUR
4.00
-40°C to +105°C
3-SOT23
SILL
ASM810TEUR
3.08
-40°C to +105°C
3-SOT23
SJLL
ASM810SEUR
2.93
-40°C to +105°C
3-SOT23
SKLL
2.63
-40°C to +105°C
3-SOT23
SLLL
ASM810REUR
ASM810 ACTIVE HIGH RESET, LEAD FREE DEVICES
ASM810LEURF
4.63
-40°C to +105°C
3-SOT23
NGLL
ASM810MEURF
4.38
-40°C to +105°C
3-SOT23
NHLL
ASM810JEURF
4.00
-40°C to +105°C
3-SOT23
NILL
ASM810TEURF
3.08
-40°C to +105°C
3-SOT23
NJLL
ASM810SEURF
2.93
-40°C to +105°C
3-SOT23
NKLL
ASM810REURF
2.63
-40°C to +105°C
3-SOT23
NLLL
Notes:
•
For parts to be packed in Tape and Reel, add “-T” at the end of the part number.
•
Alliance Semiconductor's lead free parts are RoHS compliant. All parts are Lead Free by default. Contact factory for Non Lead
Free devices
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
10 of 12
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Related Products:
Max Supply Current
Package Pins
ASM810
ASM811
ASM812
15µA
15µA
15µA
15µA
15µA
3
3
4
4
5
SOT-143
SOT-143
Manual RESET input
Package Type
SOT-23
Active-HIGH RESET Output
Active-LOW RESET Output
ASM8091
ASM809
SOT-23
SOT-23
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
11 of 12
ASM809,ASM8091,ASM810
July 2005
rev 1.8
Alliance Semiconductor Corporation
2575 Augustine Drive,
Santa Clara, CA 95054
Tel: 408 - 855 - 4900
Fax: 408 - 855 - 4999
www.alsc.com
Copyright © Alliance Semiconductor
All Rights Reserved
Part Number:
ASM809,ASM8091,ASM810
Document Version: V.1.8
© Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or
registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the
right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may
appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the
right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these
specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and
users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility
or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale
and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any
intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of
Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not
convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third
parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may
reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that
the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use.
3-Pin Microcontroller Power Supply Supervisor
Notice: The information in this document is subject to change without notice
12 of 12